Use new pin names containing DCE/DTE for UART RX/TX/RTS/CTS pins, this
is to distinguish the DCE/DTE functions.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This updates the WL1831 bluetooth to use the serial serdev driver
interface.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i2c2 bus has a external plug which enables the easy connection of external
"bricks" with sensors of various kinds, while i2c4 on the Extended/Full boards
has a pair of on board motion sensors, accelerometer and magnetometer on one chip
and gyroscope on another so it makes sense to enable these i2c buses for use.
Tested on UDOO Neo Full.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use the SPDX License Identifier for GPL-2.0+ OR X11
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
After issuing a 'reboot' command the imx6sx-udoo-neo board does not
reboot as expected and it just hangs instead.
In mainline kernel only LDO enabled mode is supported. Do not provide
arm-supply/soc-supply nodes in the device tree, so that the board operates
in LDO enabled mode and can then successfully reboot via watchdog.
Fixes: 76e691fc76 ("ARM: dts: imx6sx: Add UDOO Neo support")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Udoo Neo has a TI WL1831 Bluetooth chip connected to the UART3 port.
Add support for it.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Udoo Neo has a TI WL1831 Wifi chip connected to the USDHC3 port.
Add support for it.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for micro USB (OTG1) and USB Host (OTG2) for UDOO Neo board.
Tested on a UDOO Neo Full board by mounting a mass storage device
on both ports.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6sx-udoo-neo has a KSZ8091 Ethernet PHY, which requires the reset
signal to be low for at least 10ms.
Pass the 'phy-reset-duration' property to reflect such requirement.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add initial device trees for UDOO Neo Basic, Extended and Full boards:
* Serial console is enabled, other serial ports are prepared.
* I2C based PMIC is enabled.
* Ethernet is enabled for Basic and Full.
* SDHC is enabled, with the SDIO_PWR GPIO modeled as a regulator.
* Both user LEDs are enabled, with the orange one reserved for the M4
and with the SD card as default trigger for the red LED.
The decision on a board compatible string is deferred to later.
Cc: Ettore Chimenti <ettore.chimenti@udoo.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
