All CortexA7/A15 based Exynos5 SoCs have ARM architected timers, so enable
support for them directly in the base dtsi. None of the known firmware
properly configures CNTFRQ arch timer register, so force clock frequency
to 24MHz, which is the only configuration supported by the remaining
clock drivers so far.
Stock firmware for Peach Pit and Pi Chromebooks also doesn't reset
properly other arch timer registers, so add respective properties
indicating that. Other Exynos5-based boards behaves correctly in this area,
what finally allows to enable support for KVM-based virtualization.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Commit aff138bf8e ("ARM: dts: exynos: Add TMU nodes regulator supply
for Peach boards") assigned LDO10 to Exynos Thermal Measurement Unit,
but it turned out that it supplies also some other critical parts and
board freezes/crashes when it is turned off.
The mentioned commit made Exynos TMU a consumer of that regulator and in
typical case Exynos TMU driver keeps it enabled from early boot. However
there are such configurations (example is multi_v7_defconfig), in which
some of the regulators are compiled as modules and are not available
from early boot. In such case it may happen that LDO10 is turned off by
regulator core, because it has no consumers yet (in this case consumer
drivers cannot get it, because the supply regulators for it are not yet
available). This in turn causes the board to crash. This patch restores
'always-on' property for the LDO10 regulator.
Fixes: aff138bf8e ("ARM: dts: exynos: Add TMU nodes regulator supply for Peach boards")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The proper parent clock for audio subsystem for Exynos5420 and Exynos5800
SoCs is CLK_MAU_EPLL. This fixes following warning:
clk: failed to reparent mout_audss to fout_epll: -22
Fixes: ed7d130707: ARM: dts: exynos: Enable HDMI audio support on Peach Pit
Fixes: bae0f445c1: ARM: dts: exynos: Enable HDMI audio support on Peach Pi
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Regulators, which are marked as 'on-in-suspend' seems to be critical for
board operation, thus they must not be disabled anytime. This can be
only assured by marking them as 'always-on', because otherwise some
actions of their clients might result in turning them off. This patch
restores suspend/resume operation on Peach-Pit Chromebook board. It
partially reverts 'always-on' property removal done by the commit
mentioned in the Fixes tag.
Fixes: 665c441eea ("ARM: dts: exynos: Remove unneded always-on for regulators on Peach boards")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
After moving all nodes under "soc" node in commit 5d99cc59a3 ("ARM:
dts: exynos: Move Exynos5250 and Exynos5420 nodes under soc"), the i2c20
alias in Peach Pit and Peach Pi stopped pointing to proper node:
arch/arm/boot/dts/exynos5420-peach-pit.dtb: Warning (alias_paths):
/aliases:i2c20: aliases property is not a valid node (/spi@12d40000/cros-ec@0/i2c-tunnel)
arch/arm/boot/dts/exynos5800-peach-pi.dtb: Warning (alias_paths):
/aliases:i2c20: aliases property is not a valid node (/spi@12d40000/cros-ec@0/i2c-tunnel)
Fixes: 5d99cc59a3 ("ARM: dts: exynos: Move Exynos5250 and Exynos5420 nodes under soc")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds new cpu, codec subnodes according to the updated
"google,snow-audio-max98090" DT bindings and the I2S clock tree
configuration so sound on the HDMI interface can also be supported.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
HDMI support requires some additional off-SoC logic, so Mixer device (part
of HDMI display path) should be disabled by default in SoC dtsi and enabled
then in each board dts. This patch unifies Mixer handling with other
Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
dwmmc driver deprecated num-slots and plan to get rid
of it finally. Just move a step to cleanup it from DT.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace hard-coded values of interrupt flags with respective macros from
header to increase code readability.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
During my research I found that some of the requirements for the memory
buffers for MFC v6+ devices were blindly copied from the previous (v5)
version and simply turned out to be excessive. The relaxed requirements
are applied by the recent patches to the MFC driver and the driver is
now fully functional even without the reserved memory blocks for all
v6+ variants. This patch removes those reserved memory nodes from all
boards having MFC v6+ hardware block.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
There's a cognitive load to figure out which mmc device node corresponds
to the eMMC flash, uSD card and WiFI SDIO module on the Snow, Peach Pi
and Pit boards.
So it's better to have comments in the DTS to make this more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
[krzk: Squashed three patches into one]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace in DT sources hard-coded values for pinctrl configuration like pull
up/down, drive strength and function. This makes the DTS easier to read,
especially that some drive strengths values are quite non-obvious.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NN8A
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-pinctrl-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Topic branch for Samsung DeviceTree cleanup for 4.9" from Krzysztof Kozłowski:
Replace in DT sources hard-coded values for pinctrl configuration like pull
up/down, drive strength and function. This makes the DTS easier to read,
especially that some drive strengths values are quite non-obvious.
* tag 'samsung-dt-pinctrl-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: s3c64xx: Use macros for pinctrl configuration
ARM: dts: s3c2416: Use macros for pinctrl configuration
ARM: dts: s5pv210: Use macros for pinctrl configuration
ARM: dts: s3c64xx: Use common macros for pinctrl configuration
ARM: dts: exynos: Fix mismatched values of SD drive strengh configuration on exynos4415
ARM: dts: exynos: Fix mismatched value for SD4 pull up/down configuration on exynos4210
ARM: dts: exynos: Use macros for pinctrl configuration on exynos542x/exynos5800
ARM: dts: exynos: Use macros for pinctrl configuration on exynos5410
ARM: dts: exynos: Use macros for pinctrl configuration on exynos5260
ARM: dts: exynos: Use macros for pinctrl configuration on exynos5250
ARM: dts: exynos: Use macros for pinctrl configuration on exynos4415
ARM: dts: exynos: Use macros for pinctrl configuration on exynos4x12
ARM: dts: exynos: Use macros for pinctrl configuration on exynos4210
ARM: dts: exynos: Use macros for pinctrl configuration on exynos3250
ARM: dts: exynos: Use common macros for pinctrl configuration
pinctrl: dt-bindings: samsung: Update documentation with new macros
pinctrl: dt-bindings: samsung: Add header with values used for configuration
Usage of DTS macros instead of hard-coded numbers makes code easier to
read. One does not have to remember which value means pull-up/down or
specific driver strength.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch enables getting a HPD GPIO descriptor quicker.
The exynos-hdmi driver uses "hpd" for HDMI hot plug detection.
static int hdmi_resources_init(struct hdmi_context *hdata)
{
...
hdata->hpd_gpio = devm_gpiod_get(dev, "hpd", GPIOD_IN);
...
}
This calls 'of_find_gpio()' and it generates the GPIO consumer ID by referring
GPIO suffix. So 'hpd-gpios' is preferred on getting a GPIO descriptor.
However, if the device tree uses 'hpd-gpio', then the exynos-hdmi driver
always retries to get a GPIO descriptor because the first GPIO suffix is not
'gpio' but 'gpios'. So you always see the debug message below.
of_get_named_gpiod_flags: can't parse 'hpd-gpios' property of node '/soc/hdmi@14530000[0]'
Use the preferred property, 'hpd-gpios' instead of 'hpd-gpio'.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Device tree contents continue to be the largest branches we submit. This
time around, some of the contents worth pointing out is:
- New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large delta due
to indentation changes
- A new Tegra K1 board: Apalis
- A bunch of small updates to many Allwinner platforms; new hardware support,
some cleanup, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C4NU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Device tree contents continue to be the largest branches we submit.
This time around, some of the contents worth pointing out is:
New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large
delta due to indentation changes
- a new Tegra K1 board: Apalis
- a bunch of small updates to many Allwinner platforms; new hardware
support, some cleanup, etc"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (426 commits)
ARM: dts: sun8i: Add dts file for inet86dz board
ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
ARM: dts: at91: Don't build unnecessary dtbs
ARM: dts: at91: sama5d3x: separate motherboard gmac and emac definitions
ARM: dts: at91: at91sam9g25ek: fix isi endpoint node
ARM: dts: at91: move isi definition to at91sam9g25ek
ARM: dts: at91: fix i2c-gpio node name
ARM: dts: at91: vinco: fix regulator name
ARM: dts: at91: ariag25 : fix onewire node
...
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXnm1XAAoJEIwa5zzehBx35lcP/ApuQarIXeZCQZtjlUBV9McW
o3o7FhKFHePmEPeoYCvVeK5D8NykTkQv3WpnCknoxPJzxGJF7jbPWQJcVnXfKOXD
kTcyIK15WL2HHtSE3lYyLfyUPz8AbJyRt0l0cxgcg6jvo+uzlWooNz1y78rLIYzg
UwRssj7OiHv4dsyYRHZIsjnB8gMWw8rYMk154gP2xy6MnNXXzzOVVnOiVqxSZBm+
EgIIcROMOqkkHuFlClMYKluIgrmgz1Ypjf+FuAg7dqXZd+TGRrmGXeI7SkGThfLu
nyvY3N18NViNu7xOUkI9zg7+ifyYM8Si9ylalSICSJdIAxZfiwFqFaLJvVWKU1rY
rBOBjKckQI0/X9WYusFNFHcijhIFV8/FgGAnVRRMPdvlCss7Zp03C9mR4AEhmKMX
rLG49x81hU1C+LftC59ml3iB8dhZrrRkbxNHjLFHVGWNrKMrmJKa8JhXGRAoNM+u
LRauiuJZatqvLfISNvpfcoW2EashVoU3f+uC8ymT3QCyME3wZm0t7T4tllxhMfBl
sOgJqNkTKDmPLofwm/dASiLML7ZF1WePScrFyOACnj9K4mUD+OaCnowtWoQPu0eI
aNmT84oosJ2S9F/iUDPtFHXdzQ+1QPPfSiQ9FXMoauciVq/2F+pqq68yYgqoxFOG
vmkmG2YM4Wyq43u0BONR
=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
Replace hardcoded reserved memory ranges with auto-allocated ones
and enable MFC for all boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sS8p
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-exynos-mfc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Topic branch for Exynos MFC changes for v4.8, part 2:
Replace hardcoded reserved memory ranges with auto-allocated ones
and enable MFC for all boards.
* tag 'samsung-drivers-exynos-mfc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: enable MFC device for all boards
ARM: dts: exynos: move MFC reserved memory regions from boards to .dtsi
ARM: dts: exynos: replace hardcoded reserved memory ranges with auto-allocated ones
ARM: dts: exynos: Enable MFC device on Exynos4412 Odroid boards
ARM: dts: exynos: Convert MFC device to generic reserved memory bindings
ARM: EXYNOS: Remove code for MFC custom reserved memory handling
media: s5p-mfc: add iommu support
media: s5p-mfc: replace custom reserved memory handling code with generic one
media: s5p-mfc: use generic reserved memory bindings
of: reserved_mem: add support for using more than one region for given device
media: set proper max seg size for devices on Exynos SoCs
media: vb2-dma-contig: add helper for setting dma max seg size
s5p-mfc: Fix race between s5p_mfc_probe() and s5p_mfc_open()
s5p-mfc: Add release callback for memory region devs
s5p-mfc: Set device name for reserved memory region devs
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch moves assigning reserved memory regions from each board dts
to common exynos-mfc-reserved-memory.dtsi file, where those regions are
defined.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Commit bea7eef694 ("ARM: dts: exynos: Fix DTC unit name warnings in
Peach Pit") fixed the DTC warnings about mismatches between unit names
and reg properties in the Exynos5420 Peach Pit DTS.
But unfortunately it also added a regression on the Peach Pit when
changing the port node names since the OF graph logic expects the port
nodes to be always named 'port'.
The Documentation/devicetree/bindings/graph.txt binding document says
that when there is more than one port, '#address-cells', '#size-cells'
and 'reg' properties should be used to number the port nodes.
Fixes: bea7eef694 ("ARM: dts: exynos: Fix DTC unit name warnings in Peach Pit")
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch replaces custom properties for defining reserved memory
regions with generic reserved memory bindings for MFC video codec
device.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
[k.kozlowski: Add Samsung copyrights]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The Exynos5800 Peach Pi and Exynos5420 Peach Pit Chromebooks have the
LDO10 1.8V output connected to the VDD18_TS{01,23,4} Exynos SoC pins.
Add this regulator as the input supply of the Thermal Management Unit
channels and also remove the always-on property since all the devices
using LDO10 as input supply are now defined.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The regulator always-on property should only be used for regulators
that either can't be disabled or the drivers for the client devices
are not enabling the regulator and so being disabled due to unused.
There are some max77802 regulators in the Peach Pit and Pi boards
that are always-on but shouldn't since they are enabled by drivers:
BUCK5 is max77802 inl1 supply
BUCK7 is max77802 inl{2,10} supply
BUCK9 is max77802 inl{3,4,5,7} supply
BUCK10 is mmc1 vqmmc supply
LDO9 is adc vdd supply
This patch removes the always-on property for these regulators.
Some regulators should remain always-on even when they are used as
input supplies, because these regulators are also used by other
components that are not described in the DT, for example:
LDO10 is hdmi vdd_osc supply but it's also used as input supply for
the Exynos5420 temperature sensor.
LDO8 is hdmi vdd and vdd_pll supply but it's also used as supply for
the Exynos5420 Display port.
BUCK2 and BUCK6 are the vdd supplies for the EAGLE and KFC clusters.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Pull drm updates from Dave Airlie:
"Here's the main drm pull request for 4.7, it's been a busy one, and
I've been a bit more distracted in real life this merge window. Lots
more ARM drivers, not sure if it'll ever end. I think I've at least
one more coming the next merge window.
But changes are all over the place, support for AMD Polaris GPUs is in
here, some missing GM108 support for nouveau (found in some Lenovos),
a bunch of MST and skylake fixes.
I've also noticed a few fixes from Arnd in my inbox, that I'll try and
get in asap, but I didn't think they should hold this up.
New drivers:
- Hisilicon kirin display driver
- Mediatek MT8173 display driver
- ARC PGU - bitstreamer on Synopsys ARC SDP boards
- Allwinner A13 initial RGB output driver
- Analogix driver for DisplayPort IP found in exynos and rockchip
DRM Core:
- UAPI headers fixes and C++ safety
- DRM connector reference counting
- DisplayID mode parsing for Dell 5K monitors
- Removal of struct_mutex from drivers
- Connector registration cleanups
- MST robustness fixes
- MAINTAINERS updates
- Lockless GEM object freeing
- Generic fbdev deferred IO support
panel:
- Support for a bunch of new panels
i915:
- VBT refactoring
- PLL computation cleanups
- DSI support for BXT
- Color manager support
- More atomic patches
- GEM improvements
- GuC fw loading fixes
- DP detection fixes
- SKL GPU hang fixes
- Lots of BXT fixes
radeon/amdgpu:
- Initial Polaris support
- GPUVM/Scheduler/Clock/Power improvements
- ASYNC pageflip support
- New mesa feature support
nouveau:
- GM108 support
- Power sensor support improvements
- GR init + ucode fixes.
- Use GPU provided topology information
vmwgfx:
- Add host messaging support
gma500:
- Some cleanups and fixes
atmel:
- Bridge support
- Async atomic commit support
fsl-dcu:
- Timing controller for LCD support
- Pixel clock polarity support
rcar-du:
- Misc fixes
exynos:
- Pipeline clock support
- Exynoss4533 SoC support
- HW trigger mode support
- export HDMI_PHY clock
- DECON5433 fixes
- Use generic prime functions
- use DMA mapping APIs
rockchip:
- Lots of little fixes
vc4:
- Render node support
- Gamma ramp support
- DPI output support
msm:
- Mostly cleanups and fixes
- Conversion to generic struct fence
etnaviv:
- Fix for prime buffer handling
- Allow hangcheck to be coalesced with other wakeups
tegra:
- Gamme table size fix"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1050 commits)
drm/edid: add displayid detailed 1 timings to the modelist. (v1.1)
drm/edid: move displayid validation to it's own function.
drm/displayid: Iterate over all DisplayID blocks
drm/edid: move displayid tiled block parsing into separate function.
drm: Nuke ->vblank_disable_allowed
drm/vmwgfx: Report vmwgfx version to vmware.log
drm/vmwgfx: Add VMWare host messaging capability
drm/vmwgfx: Kill some lockdep warnings
drm/nouveau/gr/gf100-: fix race condition in fecs/gpccs ucode
drm/nouveau/core: recognise GM108 chipsets
drm/nouveau/gr/gm107-: fix touching non-existent ppcs in attrib cb setup
drm/nouveau/gr/gk104-: share implementation of ppc exception init
drm/nouveau/gr/gk104-: move rop_active_fbps init to nonctx
drm/nouveau/bios/pll: check BIT table version before trying to parse it
drm/nouveau/bios/pll: prevent oops when limits table can't be parsed
drm/nouveau/volt/gk104: round up in gk104_volt_set
drm/nouveau/fb/gm200: setup mmu debug buffer registers at init()
drm/nouveau/fb/gk20a,gm20b: setup mmu debug buffer registers at init()
drm/nouveau/fb/gf100-: allocate mmu debug buffers
drm/nouveau/fb: allow chipset-specific actions for oneinit()
...
These are all the updates to device tree files for 32-bit platforms,
which as usual makes up the bulk of the ARM SoC changes: 462 non-merge
changesets, 450 files changed, 23340 insertions, 5216 deletions.
The three platforms that are added with the "soc" branch are here as well,
and we add some related machine files:
- For Aspeed AST2400/AST2500, we get the evaluation platform and
the Tyan Palmetto POWER8 mainboard that uses the AST2400 BMC
- For Oxnas 810SE, the Western Digital "My Book World Edition"
is added as the only platform at the moment.
- For ARM MPS2, the AN385 (Cortex-M3) and AN399 (Cortex-M7)
are supported
On the ARM Realview development platform, we now support all machines
with device tree, previously only the board files were supported, which
in turn will likely be removed soon.
Qualcomm IPQ4019 is the second generation ARM based "Internet Processor",
following the IPQ806x that is used in many high-end WiFi routers. This one
integrates two ath10k wifi radios that were previously on separate chips.
Other boards that got added for existing chips are:
- On Ti OMAP family:
- Amazon Kindle Fire, first generation, tablet and ebook reader
- OnRISC Baltos iR 2110 and 3220 embedded industrial PCs
- TI AM5728 IDK, TI AM3359 ICE-V2, and TI DRA722 Rev C EVM
development systems
- On Samsung EXYNOS platform:
- Samsung ARTIK5 evaluation board, see
https://www.artik.io/modules/overview/artik-5/
- On NXP i.MX platforms:
- Ka-Ro electronics TX6S-8034, TX6S-8035, TX6U-8033, TX6U-81xx,
TX6Q-1036, TX6Q-1110/-1130, TXUL-0010 and TXUL-0011 industrial
SoM modules
- Embest MarS Board i.MX6Dual DIY platform
- Boundary Devices i.MX6 Quad Plus Nitrogen6_MAX and
SoloX Nitrogen6sx embedded boards
- Technexion Pico i.MX6UL compute module
- ZII VF610 Development Board
- On Marvell embedded (mvebu, orion, kirkwood) platforms:
- Linksys Viper (E4200v2 / EA4500) WiFi router
- Buffalo Kurobox Pro NAS
- On Qualcomm Snapdragon:
- Arrow DragonBoard 600c (96boards) with APQ8064 Snapdragon 600
- On Rockchips platform:
- mqmaker MiQi single-board computer
- On Altera SoCFPGA:
- samtec VIN|ING 1000 vehicle communication interface
- On Allwinner Sunxi platforms:
- Dserve DSRV9703C tablet
- Difrnce DIT4350 tablet
- Colorfly E708 Q1 tablet
- Polaroid MID2809PXE04 tablet
- Olimex A20 OLinuXino LIME2 single board computer
- Xunlong Orange Pi 2, Orange Pi One, and Orange Pi PC
single board computers
Across many platforms, bug fixes went in to address warnings that
dtc now emits with 'make dtbs W=1'. Further changes for device enablement
went into Ti OMAP, bcm283x (Raspberry Pi), bcm47xx (wifi router),
Ti Davinci, Samsung EXYNOS, Marvell mvebu/kirkwood/orion, NXP i.MX/Vybrid
NXP LPC18xx, NXP LPC32xx, Renesas shmobile/r-mobile/r-car, Rockchips
rk3xxx, ST Ux500, ST STi, Atmel AT91/SAMA5, Altera SoCFPGA, Allwinner
Sunxi, Sigma Designs Tango, NVIDIA Tegra, Socionext Uniphier and ARM
Versatile Express.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Nx46
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"These are all the updates to device tree files for 32-bit platforms,
which as usual makes up the bulk of the ARM SoC changes: 462 non-merge
changesets, 450 files changed, 23340 insertions, 5216 deletions.
The three platforms that are added with the "soc" branch are here as
well, and we add some related machine files:
- For Aspeed AST2400/AST2500, we get the evaluation platform and the
Tyan Palmetto POWER8 mainboard that uses the AST2400 BMC
- For Oxnas 810SE, the Western Digital "My Book World Edition" is
added as the only platform at the moment.
- For ARM MPS2, the AN385 (Cortex-M3) and AN399 (Cortex-M7) are
supported
On the ARM Realview development platform, we now support all machines
with device tree, previously only the board files were supported,
which in turn will likely be removed soon.
Qualcomm IPQ4019 is the second generation ARM based "Internet
Processor", following the IPQ806x that is used in many high-end WiFi
routers. This one integrates two ath10k wifi radios that were
previously on separate chips.
Other boards that got added for existing chips are:
Ti OMAP family:
- Amazon Kindle Fire, first generation, tablet and ebook reader
- OnRISC Baltos iR 2110 and 3220 embedded industrial PCs
- TI AM5728 IDK, TI AM3359 ICE-V2, and TI DRA722 Rev C EVM
development systems
Samsung EXYNOS platform:
- Samsung ARTIK5 evaluation board, see
https://www.artik.io/modules/overview/artik-5/
NXP i.MX platforms:
- Ka-Ro electronics TX6S-8034, TX6S-8035, TX6U-8033, TX6U-81xx,
TX6Q-1036, TX6Q-1110/-1130, TXUL-0010 and TXUL-0011 industrial
SoM modules
- Embest MarS Board i.MX6Dual DIY platform
- Boundary Devices i.MX6 Quad Plus Nitrogen6_MAX and SoloX
Nitrogen6sx embedded boards
- Technexion Pico i.MX6UL compute module
- ZII VF610 Development Board
Marvell embedded (mvebu, orion, kirkwood) platforms:
- Linksys Viper (E4200v2 / EA4500) WiFi router
- Buffalo Kurobox Pro NAS
Qualcomm Snapdragon:
- Arrow DragonBoard 600c (96boards) with APQ8064 Snapdragon 600
Rockchips platform:
- mqmaker MiQi single-board computer
Altera SoCFPGA:
- samtec VIN|ING 1000 vehicle communication interface
Allwinner Sunxi platforms:
- Dserve DSRV9703C tablet
- Difrnce DIT4350 tablet
- Colorfly E708 Q1 tablet
- Polaroid MID2809PXE04 tablet
- Olimex A20 OLinuXino LIME2 single board computer
- Xunlong Orange Pi 2, Orange Pi One, and Orange Pi PC single board
computers
Across many platforms, bug fixes went in to address warnings that dtc
now emits with 'make dtbs W=1'. Further changes for device enablement
went into Ti OMAP, bcm283x (Raspberry Pi), bcm47xx (wifi router), Ti
Davinci, Samsung EXYNOS, Marvell mvebu/kirkwood/orion, NXP i.MX/Vybrid
NXP LPC18xx, NXP LPC32xx, Renesas shmobile/r-mobile/r-car, Rockchips
rk3xxx, ST Ux500, ST STi, Atmel AT91/SAMA5, Altera SoCFPGA, Allwinner
Sunxi, Sigma Designs Tango, NVIDIA Tegra, Socionext Uniphier and ARM
Versatile Express"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (458 commits)
ARM: dts: tango4: Import watchdog node
ARM: dts: tango4: Update cpus node for cpufreq
ARM: dts: tango4: Update DT to match clk driver
ARM: dts: tango4: Initial thermal support
arm/dst: Add Aspeed ast2500 device tree
arm/dts: Add Aspeed ast2400 device tree
ARM: sun7i: dt: Add pll3 and pll7 clocks
ARM: dts: sunxi: Add a olinuxino-lime2-emmc
ARM: dts: at91: sama5d4: add trng node
ARM: dts: at91: sama5d3: add trng node
ARM: dts: at91: sama5d2: add trng node
ARM: dts: at91: at91sam9g45 family: reduce the trng register map size
ARM: sun4i: dt: Add pll3 and pll7 clocks
ARM: sun5i: chip: Enable the TV Encoder
ARM: sun5i: r8: Add display blocks to the DTSI
ARM: sun5i: a13: Add display and TCON clocks
ARM: dts: ux500: configure the accelerometers open drain
ARM: mx5: dts: Enable USB OTG on M53EVK
ARM: dts: imx6ul-14x14-evk: Add audio support
ARM: dts: imx6qdl: Remove unneeded unit-addresses
...
The MFC nodes with the memory regions reserved for memory allocations
are missing in the Exynos5420 Peach Pit and Exynos5800 Peach Pi DTS.
This causes the s5p-mfc driver probe to fail with the following error:
[ 4.140647] s5p_mfc_alloc_memdevs:1072: Failed to declare coherent memory for MFC device
[ 4.216163] s5p-mfc: probe of 11000000.codec failed with error -12
Add the missing nodes so the driver probes and the {en,de}coder video
nodes are registered correctly:
[ 4.096277] s5p-mfc 11000000.codec: decoder registered as /dev/video4
[ 4.102282] s5p-mfc 11000000.codec: encoder registered as /dev/video5
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fix following DTC warnings in Exynos5420 Peach Pit:
Warning (unit_address_vs_reg): Node /dp-controller@145B0000/ports/port@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c@12CD0000/lvds-bridge@48/ports/port@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c@12CD0000/lvds-bridge@48/ports/port@1 has a unit name, but no reg property
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
This pull request want to land the analogix_dp driver into drm/bridge directory,
which reused the Exynos DP code, and add Rockchip DP support. And those
patches have been:
* 'drm-next-analogix-dp-v2' of github.com:yakir-Yang/linux:
drm: bridge: analogix/dp: Fix the possible dead lock in bridge disable time
drm: bridge: analogix/dp: add panel prepare/unprepare in suspend/resume time
drm: bridge: analogix/dp: add edid modes parse in get_modes method
drm: bridge: analogix/dp: move hpd detect to connector detect function
drm: bridge: analogix/dp: try force hpd after plug in lookup failed
drm: bridge: analogix/dp: add max link rate and lane count limit for RK3288
drm: bridge: analogix/dp: add some rk3288 special registers setting
dt-bindings: add document for rockchip variant of analogix_dp
drm: rockchip: dp: add rockchip platform dp driver
ARM: dts: exynos/dp: remove some properties that deprecated by analogix_dp driver
dt-bindings: add document for analogix display port driver
drm: bridge: analogix/dp: dynamic parse sync_pol & interlace & dynamic_range
drm: bridge: analogix/dp: remove duplicate configuration of link rate and link count
drm: bridge: analogix/dp: fix some obvious code style
drm: bridge: analogix/dp: rename register constants
drm/exynos: dp: rename implementation specific driver part
drm: bridge: analogix/dp: split exynos dp driver to bridge directory
After exynos_dp have been split the common IP code into analogix_dp driver,
the analogix_dp driver have deprecated some Samsung platform properties which
could be dynamically parsed from EDID/MODE/DPCD message, so this is an update
for Exynos DTS file for dp-controller.
Beside the backward compatibility is fully preserved, so there are no
bisectability break that make this change in a separate patch.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux-keypad,wakeup" boolean property to enable the
wakeup source, "wakeup-source" is the new standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Add cluster regulator supply properties as a preparation to
adding generic cpufreq-dt driver support for Exynos542x and
Exynos5800 based boards.
Cc: Doug Anderson <dianders@chromium.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Andreas Faerber <afaerber@suse.de>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Exynos5420 and Exynos5800 boards boot from big core (A15) but
Exynos5422 boards choose otherwise: LITTLE core (A7) (on Exynos5422 this
is property of the board - configurable by pulling up/down gpg2-1).
To make user-visible CPU ordering more consistent the 'cpus' node was
overridden by exynos5422-cpus.dtsi.
However this is a little bit ugly and error-prone. Overriding the CPU
child nodes requires to basically reverse what was done initially in
exynos5420.dtsi.
Instead, split CPU configuration entirely to separate files which should
be included by board DTS.
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanho Park <parkch98@gmail.com>
The eMMC is non-removable so is marked with the non-removable DT
property to avoid having to redetect it after a suspend/resume.
But it also has the broken-cd property which is wrong since only
one of the DT properties for card detection should be used.
Also remove the card-detect-delay property that is not needed with
non-removable.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The Exynos5420 Peach Pit Chromebook has a Marvell WiFi SDIO chip which
can't neither be removed nor be detected. But the node isn't marked
as non-removable and instead has the broken-cd DT property.
This causes the device to be removed when the system enters into a
suspend state and the following warnings is shown after a resume:
[ 181.944636] mmc2: error -2 during resume (card was removed?)
Also remove the card-detect-delay property that is not needed with
non-removable.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
As usual, this is the massive branch we have for each release. Lots of
various updates and additions of hardware descriptions on existing hardware,
as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and 32-bit
DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to tell
from the diffstat, so there's little point in duplicating listing it here.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qY1q
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, this is the massive branch we have for each release. Lots
of various updates and additions of hardware descriptions on existing
hardware, as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and
32-bit DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to
tell from the diffstat, so there's little point in duplicating listing
it here)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (499 commits)
ARM: dts: uniphier: add system-bus-controller nodes
ARM64: juno: disable NOR flash node by default
ARM: dts: uniphier: add outer cache controller nodes
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
ARM: dts: uniphier: add I2C aliases for ProXstream2 boards
dts/Makefile: Add build support for LS2080a QDS & RDB board DTS
dts/ls2080a: Add DTS support for LS2080a QDS & RDB boards
dts/ls2080a: Update Simulator DTS to add support of various peripherals
dts/ls2080a: Remove text about writing to Free Software Foundation
dts/ls2080a: Update DTSI to add support of various peripherals
doc: DTS: Update DWC3 binding to provide reference to generic bindings
doc/bindings: Update GPIO devicetree binding documentation for LS2080A
Documentation/dts: Move FSL board-specific bindings out of /powerpc
Documentation: DT: Add entry for FSL LS2080A QDS and RDB boards
arm64: Rename FSL LS2085A SoC support code to LS2080A
arm64: Use generic Layerscape SoC family naming
ARM: dts: uniphier: add ProXstream2 Vodka board support
ARM: dts: uniphier: add ProXstream2 Gentil board support
...
The board DTS are using numeric values instead of the defined GPIO
constanst to express polarity, use them to make the DTS more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Peach boards use the EC to store the vboot context information,
so add the corresponding properties on the EC node to indicate so.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Emilio Lopez <emilio.lopez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes. Additionally remove duplicated serial and uart labels
for serial.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Marvell mwifiex driver prevents the system to enter into a suspend
state if the card power is not preserved during a suspend/resume cycle.
So Suspend-to-RAM and Suspend-to-idle is failing on Exynos5800 Peach Pi
and Exynos5420 Peach Pit Chromebooks.
Add the keep-power-in-suspend Power Management property to the SDIO/MMC
node so the mwifiex suspend handler doesn't fail and the system is able
to enter into a suspend state.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
HS400 timing values are added for SMDK5420, exynos5420-peach-pit
and exynos5800-peach-pi boards. This also adds RCLK GPIO line,
this gpio should be in pull-down state.
This also enables HS400 on peach-pi and this updates the clock
frequency to 800MHz to be set as input clock to controller.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
[alim.akhtar@samsung.com: addressed review comments]
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The kernel can use as the default console a serial port if is defined
as stdout device in the Device Tree.
This allows a board to be booted without the need of having a console
parameter in the kernel command line.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
On Peach Pit and Pi boards, the Exynos SoC XCLKOUT pin provides
master clock (mclk) to the codec. So make it a clock consumer.
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Peach Pit and Pi boards have a WiFi module that is always powered
but needs toggling an enable pin and ungating a 32kHz reference
clock as part of their power sequencing.
Add a dev node for the SDIO slot and a MMC power sequence provider.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Exynos5420 SoC has 3 sets of 8 pads used as data lines for the 3
MMC/SD/SDIO slots. These needs to be muxed as SD_n_DATA instead of a
GPIO or external interrupt to allow the MMC controller to communicate
with the attached cards or SDIO devices.
Which data lines needs to be muxed as SD_n_DATA depends on the bus
width used for data transfer:
* bus-width = <1> needs SD_n_DATA[0]
* bus-width = <4> needs SD_n_DATA[0-3]
* bus-width = <8> needs SD_n_DATA[0-7]
The Exynos5250-pinctrl.dtsi file that defines the groups of pins has
SD_n_DATA[0] muxed for both sdn_bus1 and sdn_bus4 so just one of them
needs to be included in the device node's pinctrl property.
But Exynos5420-pinctrl has a different definition and only includes
SD_n_DATA[1-3] for sdn_bus4. So for a bus-width = <4>, both sdn_bus1
and sdn_bus4 have to be in the dev pinctrl to mux all the needed pads.
It seems all Exynos5420 boards had just cargo cult the pinctrl lines
assuming that sdn_bus4 also included SD_n_DATA[0] and it only works
because the bootloader muxes the pads correctly. But that is not the
case for the devices not used by the bootloader such as WiFi modules.
Add sdn_bus1 too in the nodes pinctrl to not rely on the bootloader.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Define videoports and use endpoints to describe the connection between
the encoder, bridge and the panel, instead of using phandles.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The regulator core now has support to choose if a regulator
has to be enabled or disabled during system suspend and also
supports changing the regulator operating mode during runtime
and when the system enters into sleep mode.
To lower power during suspend, configure the regulators state
using the same configuration found in the ChromeOS 3.8 kernel
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Exynos5420 Peach Pit and Exynos5800 Peach Pi boards have a built-in
Silicon Motion USB UVC WebCam whose power supply is the tps65090 fet5
regulator. Since the camera uses the generic USB Video Class driver and
this does not grab a regulator, mark the regulator as always on so the
USB device is enumerated and usable.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
