Before commit f1b65df5a2 ("IB/mlx5: Add support for active_width and
active_speed in RoCE"), the mlx5_ib driver set the default active_width
and active_speed to IB_WIDTH_4X and IB_SPEED_QDR.
When the RoCE port is down, the RoCE port does not negotiate the active
width with the remote side, causing the active width to be zero. When
running userspace ibstat to view the port status, ibstat will panic as it
reads an invalid width from sys file.
This patch restores the original behavior.
Fixes: f1b65df5a2 ("IB/mlx5: Add support for active_width and active_speed in RoCE").
Signed-off-by: Honggang Li <honli@redhat.com>
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Reviewed-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Before commit f1b65df5a2 ("IB/mlx5: Add support for active_width and
active_speed in RoCE"), the mlx5_ib driver set default active_width and
active_speed to IB_WIDTH_4X and IB_SPEED_QDR.
Now, the active_width and active_speed are zeros if the RoCE port
is in DOWN state. The speed string should be set to " SDR" instead of
a blank string when active_speed is zero.
Signed-off-by: Honggang Li <honli@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
notify uld drivers if the adapter encounters fatal
error.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a default, for Ethernet packets, the device scatters only the payload
of ingress packets. The scatter FCS feature lets the user to get the FCS
(Ethernet's frame check sequence) in the received WR's buffer as a 4
Bytes trailer following the packet's payload.
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Guy Levi <guyle@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Report to the user area the TSO device capabilities, it includes the
max_tso size and the QP types that support it.
The TSO is applicable only when when of the ports is ETH and the device
supports it.
uresp logic around rss_caps is updated to fix a till-now harmless bug
computing the length of the structure to copy. The code did not handle the
implicit padding before rss_caps correctly. This is necessay to copy
tss_caps successfully.
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
There is no explicit tear-down sequence initiated on
connections if the Control QP OP, Modify QP to close,
fails. Fix this by triggering a driver generated
Asynchronous Event (AE) on Modify QP failures and
tear-down the connection on receipt of the AE.
This fix can be generalized to other Modify QP failures
(i.e. RTS->TERM, IDLE->RTS, etc) as any modify failure
will require a connection tear-down.
Fixes: d374984179 ("i40iw: add files for iwarp interface")
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The flush CQP OP can be used to optionally generate
Asynchronous Events (AEs) in addition to QP flush.
Consolidate all HW AE generation code under a new
function i40iw_gen_ae which use the flush CQP OP
to only generate AEs.
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Open coding a loose value is not acceptable for describing the uABI in
RDMA. Provide the missing struct.
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Open coding a loose value is not acceptable for describing the uABI in
RDMA. Provide the missing struct.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
All of these defines are part of the uABI for the driver, this
header duplicates providers/i40iw/i40iw-abi.h in rdma-core.
Acked-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
MLX4_USER_DEV_CAP_LARGE_CQE (via mlx4_ib_alloc_ucontext_resp.dev_caps)
and MLX4_IB_QUERY_DEV_RESP_MASK_CORE_CLOCK_OFFSET (via
mlx4_uverbs_ex_query_device_resp.comp_mask) are copied directly to
userspace and form part of the uAPI.
Move them to the uapi header where they belong.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Open coding pointer math is not acceptable for describing the uABI in
RDMA. Provide structs for all the cases.
The udata is casted to the struct as close to the verbs entry point
as possible for maximum clarity. Function signatures and so forth
are revised to allow for this.
Tested-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
It isn't used and it couldn't possibly ever be used correctly.
Tested-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
rvt_mregion uses percpu_ref for reference counting and RCU to protect
accesses from lkey_table. When a rvt_mregion needs to be freed, it
first gets unregistered from lkey_table and then rvt_check_refs() is
called to wait for in-flight usages before the rvt_mregion is freed.
rvt_check_refs() seems to have a couple issues.
* It has a fast exit path which tests percpu_ref_is_zero(). However,
a percpu_ref reading zero doesn't mean that the object can be
released. In fact, the ->release() callback might not even have
started executing yet. Proceeding with freeing can lead to
use-after-free.
* lkey_table is RCU protected but there is no RCU grace period in the
free path. percpu_ref uses RCU internally but it's sched-RCU whose
grace periods are different from regular RCU. Also, it generally
isn't a good idea to depend on internal behaviors like this.
To address the above issues, this patch removes the fast exit and adds
an explicit synchronize_rcu().
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: linux-rdma@vger.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Code includes wmb() followed by writel() in multiple places. writel()
already has a barrier on some architectures like arm64.
This ends up CPU observing two barriers back to back before executing the
register write.
Since code already has an explicit barrier call, changing writel() to
writel_relaxed().
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch changes the type of cqn from u32 to u64 to keep
userspace and kernel consistent, initializes resp both for
cq and qp to zeros, and also changes the condition judgment
of outlen considering future caps extension.
Suggested-by: Jason Gunthorpe <jgg@mellanox.com>
Fixes: e088a685ea (hns: Support rq record doorbell for the user space)
Fixes: 9b44703d0a (hns: Support cq record doorbell for the user space)
Signed-off-by: Yixian Liu <liuyixian@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Before commit [1], rdma_addr_find_l2_eth_by_grh() was an exported function
and therefore declaration in include/rdma/ib_addr.h was fine.
But now that its scope is limited to ib_core module, its better to have it
in core_priv.h.
[1] commit 1060f86534 ("IB/{core/cm}: Fix generating a return AH for
RoCEE")
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Introduce and use helper function get_cm_port_from_path() to get
cm_port based on the the path record entry.
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Resolving route for RoCE for a path record is needed only for the
received CM requests.
Therefore,
(a) ib_init_ah_attr_from_path() is refactored first to isolate the
code of resolving route.
(b) Setting dlid, path bits is not needed for RoCE.
Additionally ah attribute initialization is done from the path record
entry, so it is better to refer to path record entry type for
different link layer instead of ah attribute type while initializing
ah attribute itself.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add and use helper function add_cm_id_to_port_list() to attach
cm_id to port list.
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
add_gid() and del_gid() are optional callback routines.
ib_core ignores invoking them while updating GID table entries if
they are not implemented by provider drivers. Therefore remove them.
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
rdma_resolve_ip_route() is used only by ib_core module. Therefore it is
removed as an exported symbol.
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
rdma_protocol_roce() API from the ib_core already provides a way to
detect whether a given device+port is RoCE or not.
Therefore, make use of it and avoid implementing it again in rdmacm
module.
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
ah_attr contains the port number to which cm_id is bound. However, while
searching for GID table for matching GID entry, the port number is
ignored.
This could cause the wrong GID to be used when the ah_attr is converted to
an AH.
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The return status of ib_init_ah_from_mcmember() is ignored by
cma_ib_mc_handler(). Honor it and return error event if ah attribute
initialization failed.
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
ib_find_gid() is only used by IPoIB driver. For IB link layer, GID table
entries are not based on netdevice. Netdevice parameter is unused here.
Therefore, it is removed.
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Exported symbol's comments should be with function definition and not in
the header file. Therefore comments of ib_find_cached_gid() and
ib_find_cached_gid_by_port() functions are moved closer to their
definitions.
The function name in then comment is different than the actual function
name, fix it to be same as ib_cache_gid_find_by_filter().
Also current comment section of ib_find_cached_gid_by_port() contains the
desciption of ib_find_cached_gid(), fix that as well.
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The failure to destroy the MRs is printed on mlx5_core layer
as error and it makes warning prints useless.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
"live" is needed for ODP only and is better to be guarded
by appropriate CONFIG.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
According to the IBTA spec 1.3, the driver failure in
MR reregister shall release old and new MRs.
C11-20: If the CI returns any other error, the CI shall
invalidate both "old" and "new" registrations, and release
any associated resources.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Return -EOPNOTSUPP value to the user for unsupported reg_user_mr.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The mlx5_ib_alloc_implicit_mr() can fail to acquire pages
and the returned mr pointer won't be valid. Ensure that it
is not error prior to access.
Cc: <stable@vger.kernel.org> # 4.10
Fixes: 81713d3788 ("IB/mlx5: Add implicit MR support")
Reported-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
Signed-off-by: Doug Ledford <dledford@redhat.com>
On 32-bit targets, we otherwise get a warning about an impossible constant
integer expression:
In file included from include/linux/kernel.h:11,
from include/linux/interrupt.h:6,
from drivers/infiniband/hw/bnxt_re/ib_verbs.c:39:
drivers/infiniband/hw/bnxt_re/ib_verbs.c: In function 'bnxt_re_query_device':
include/linux/bitops.h:7:24: error: left shift count >= width of type [-Werror=shift-count-overflow]
#define BIT(nr) (1UL << (nr))
^~
drivers/infiniband/hw/bnxt_re/bnxt_re.h:61:34: note: in expansion of macro 'BIT'
#define BNXT_RE_MAX_MR_SIZE_HIGH BIT(39)
^~~
drivers/infiniband/hw/bnxt_re/bnxt_re.h:62:30: note: in expansion of macro 'BNXT_RE_MAX_MR_SIZE_HIGH'
#define BNXT_RE_MAX_MR_SIZE BNXT_RE_MAX_MR_SIZE_HIGH
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/infiniband/hw/bnxt_re/ib_verbs.c:149:25: note: in expansion of macro 'BNXT_RE_MAX_MR_SIZE'
ib_attr->max_mr_size = BNXT_RE_MAX_MR_SIZE;
^~~~~~~~~~~~~~~~~~~
Fixes: 872f357824 ("RDMA/bnxt_re: Add support for MRs with Huge pages")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Building for a 32-bit target results in a couple of warnings from casting
between a 32-bit pointer and a 64-bit integer:
drivers/infiniband/hw/bnxt_re/qplib_fp.c: In function 'bnxt_qplib_service_nq':
drivers/infiniband/hw/bnxt_re/qplib_fp.c:333:23: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
bnxt_qplib_arm_srq((struct bnxt_qplib_srq *)q_handle,
^
drivers/infiniband/hw/bnxt_re/qplib_fp.c:336:12: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
(struct bnxt_qplib_srq *)q_handle,
^
In file included from include/linux/byteorder/little_endian.h:5,
from arch/arm/include/uapi/asm/byteorder.h:22,
from include/asm-generic/bitops/le.h:6,
from arch/arm/include/asm/bitops.h:342,
from include/linux/bitops.h:38,
from include/linux/kernel.h:11,
from include/linux/interrupt.h:6,
from drivers/infiniband/hw/bnxt_re/qplib_fp.c:39:
drivers/infiniband/hw/bnxt_re/qplib_fp.c: In function 'bnxt_qplib_create_srq':
include/uapi/linux/byteorder/little_endian.h:31:43: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
#define __cpu_to_le64(x) ((__force __le64)(__u64)(x))
^
include/linux/byteorder/generic.h:86:21: note: in expansion of macro '__cpu_to_le64'
#define cpu_to_le64 __cpu_to_le64
^~~~~~~~~~~~~
drivers/infiniband/hw/bnxt_re/qplib_fp.c:569:19: note: in expansion of macro 'cpu_to_le64'
req.srq_handle = cpu_to_le64(srq);
Using a uintptr_t as an intermediate works on all architectures.
Fixes: 37cb11acf1 ("RDMA/bnxt_re: Add SRQ support for Broadcom adapters")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
gcc-4.4.4 has issues with initialization of anonymous unions:
drivers/infiniband/ulp/srpt/ib_srpt.c: In function 'srpt_zerolength_write':
drivers/infiniband/ulp/srpt/ib_srpt.c:854: error: unknown field 'wr_cqe' specified in initializer
drivers/infiniband/ulp/srpt/ib_srpt.c:854: warning: initialization makes integer from pointer without a cast
Work aound this.
Fixes: 2a78cb4db4 ("IB/srpt: Fix an out-of-bounds stack access in srpt_zerolength_write()")
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
gcc-4.4.4 has issues with initialization of anonymous unions.
drivers/infiniband/core/verbs.c: In function '__ib_drain_sq':
drivers/infiniband/core/verbs.c:2204: error: unknown field 'wr_cqe' specified in initializer
drivers/infiniband/core/verbs.c:2204: warning: initialization makes integer from pointer without a cast
Work around this.
Fixes: a1ae7d0345 ("RDMA/core: Avoid that ib_drain_qp() triggers an out-of-bounds stack access")
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Steve Wise <swise@opengridcomputing.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
On load we create private CQ/QP/PD in order to be used by UMR, we create
those resources after we register ourself as an IB device, and we destroy
them after we unregister as an IB device. This was changed by commit
16c1975f10 ("IB/mlx5: Create profile infrastructure to add and remove
stages") which moved the destruction before we unregistration. This
allowed to trigger an invalid memory access when unloading mlx5_ib while
there are open resources:
BUG: unable to handle kernel paging request at 00000001002c012c
...
Call Trace:
mlx5_ib_post_send_wait+0x75/0x110 [mlx5_ib]
__slab_free+0x9a/0x2d0
delay_time_func+0x10/0x10 [mlx5_ib]
unreg_umr.isra.15+0x4b/0x50 [mlx5_ib]
mlx5_mr_cache_free+0x46/0x150 [mlx5_ib]
clean_mr+0xc9/0x190 [mlx5_ib]
dereg_mr+0xba/0xf0 [mlx5_ib]
ib_dereg_mr+0x13/0x20 [ib_core]
remove_commit_idr_uobject+0x16/0x70 [ib_uverbs]
uverbs_cleanup_ucontext+0xe8/0x1a0 [ib_uverbs]
ib_uverbs_cleanup_ucontext.isra.9+0x19/0x40 [ib_uverbs]
ib_uverbs_remove_one+0x162/0x2e0 [ib_uverbs]
ib_unregister_device+0xd4/0x190 [ib_core]
__mlx5_ib_remove+0x2e/0x40 [mlx5_ib]
mlx5_remove_device+0xf5/0x120 [mlx5_core]
mlx5_unregister_interface+0x37/0x90 [mlx5_core]
mlx5_ib_cleanup+0xc/0x225 [mlx5_ib]
SyS_delete_module+0x153/0x230
do_syscall_64+0x62/0x110
entry_SYSCALL_64_after_hwframe+0x21/0x86
...
We restore the original behavior by breaking the UMR stage into two parts,
pre and post IB registration stages, this way we can restore the original
functionality and maintain clean separation of logic between stages.
Fixes: 16c1975f10 ("IB/mlx5: Create profile infrastructure to add and remove stages")
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch fixes RDMA/rxe over 802.1q VLAN devices.
Without it, I observed the following behavior:
a) adding a VLAN device to RXE via rxe_net_add() creates a non-functional
RDMA device. This is caused by the logic in enum_all_gids_of_dev_cb() /
is_eth_port_of_netdev(), which only considers networks connected to
"upper devices" of the configured network device, resulting in an empty
set of gids for a VLAN interface that is an "upper device" itself.
Later attempts to connect via this rdma device fail in cma_acuire_dev()
because no gids can be resolved.
b) adding the master device of the VLAN device instead seems to work
initially, target addresses via VLAN devices are resolved successfully.
But the connection times out because no 802.1q VLAN headers are
inserted in the ethernet packets, which are therefore never received.
This happens because the RXE layer sends the packets via the master
device rather than the VLAN device.
The problem could be solved by changing either a) or b). My thinking was
that the logic in a) was created deliberately, thus I decided to work on
b). It turns out that the information about the VLAN interface for the gid
at hand is available in the AV information. My patch converts the RXE code
to use this netdev instead of rxe->ndev. With this change, RXE over vlan
works on my test system.
Signed-off-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We get a build failure on ARM unless the header is included explicitly:
drivers/infiniband/hw/i40iw/i40iw_verbs.c: In function 'i40iw_get_vector_affinity':
drivers/infiniband/hw/i40iw/i40iw_verbs.c:2747:9: error: implicit declaration of function 'irq_get_affinity_mask'; did you mean 'irq_create_affinity_masks'? [-Werror=implicit-function-declaration]
return irq_get_affinity_mask(msix_vec->irq);
^~~~~~~~~~~~~~~~~~~~~
irq_create_affinity_masks
drivers/infiniband/hw/i40iw/i40iw_verbs.c:2747:9: error: returning 'int' from a function with return type 'const struct cpumask *' makes pointer from integer without a cast [-Werror=int-conversion]
return irq_get_affinity_mask(msix_vec->irq);
Fixes: 7e952b19eb ("i40iw: Implement get_vector_affinity API")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The mlx5 driver needs to be able to issue invalidation to ODP MRs
even if it cannot allocate memory. To this end it preallocates
emergency pages to use when the situation arises.
This flow should be extremely rare enough, that we don't need
to worry about contention and therefore a single emergency page
is good enough.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Instead synchronizing RCU in a loop when removing mkeys in a batch do it
once at the end before freeing them. The result is only waiting for one
RCU grace period instead of many serially.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
cma_port_is_unique() allows local port reuse if the quad (source
address and port, destination address and port) for this connection
is unique. However, if the destination info is zero or unspecified, it
can't make a correct decision but still allows port reuse. For example,
sometimes rdma_bind_addr() is called with unspecified destination and
reusing the port can lead to creating a connection with a duplicate quad,
after the destination is resolved. The issue manifests when MPI scale-up
tests hang after the duplicate quad is used.
Set the destination address family and add checks for zero destination
address and port to prevent source port reuse based on invalid destination.
Fixes: 19b752a19d ("IB/cma: Allow port reuse for rdma_id")
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Split IPv6 addresses at the colon that separates the IPv6 address
and the port number instead of at a colon in the middle of the IPv6
address. Check whether the IPv6 address is surrounded with square
brackets.
Fixes: 19f313438c ("IB/srp: Add RDMA/CM support")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
All callers to ib_modify_qp_is_ok() provides enum ib_qp_state
makes the checks of out-of-scope redundant. Let's remove them
together with updating function signature to return boolean result.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
QP states provided by core layer are converted to enum ib_qp_state
and better to use internal variable in that type instead of int.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The QP state is internal enum which is checked at the driver
level by calling to ib_modify_qp_is_ok(). Move this check closer
to user and leave kernel users to be checked by compiler.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
rvt_mregion uses percpu_ref for reference counting and RCU to protect
accesses from lkey_table. When a rvt_mregion needs to be freed, it
first gets unregistered from lkey_table and then rvt_check_refs() is
called to wait for in-flight usages before the rvt_mregion is freed.
rvt_check_refs() seems to have a couple issues.
* It has a fast exit path which tests percpu_ref_is_zero(). However,
a percpu_ref reading zero doesn't mean that the object can be
released. In fact, the ->release() callback might not even have
started executing yet. Proceeding with freeing can lead to
use-after-free.
* lkey_table is RCU protected but there is no RCU grace period in the
free path. percpu_ref uses RCU internally but it's sched-RCU whose
grace periods are different from regular RCU. Also, it generally
isn't a good idea to depend on internal behaviors like this.
To address the above issues, this patch removes the fast exit and adds
an explicit synchronize_rcu().
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: linux-rdma@vger.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
In hfi.h, the header file opa_addr.h is included twice.
In vt.h, the header file mmap.h is included twice.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch updates to support cq record doorbell for
the kernel space.
Signed-off-by: Yixian Liu <liuyixian@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch updates to support rq record doorbell for
the kernel space.
Signed-off-by: Yixian Liu <liuyixian@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch updates to support cq record doorbell for
the user space.
Signed-off-by: Yixian Liu <liuyixian@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds interfaces and definitions to support the rq record
doorbell for the user space.
Signed-off-by: Yixian Liu <liuyixian@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch validates user provided input to prevent integer overflow due
to integer manipulation in the mlx5_ib_create_srq function.
Cc: syzkaller <syzkaller@googlegroups.com>
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add a check for the length of the qpin structure to prevent out-of-bounds reads
BUG: KASAN: slab-out-of-bounds in create_raw_packet_qp+0x114c/0x15e2
Read of size 8192 at addr ffff880066b99290 by task syz-executor3/549
CPU: 3 PID: 549 Comm: syz-executor3 Not tainted 4.15.0-rc2+ #27 Hardware
name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org 04/01/2014
Call Trace:
dump_stack+0x8d/0xd4
print_address_description+0x73/0x290
kasan_report+0x25c/0x370
? create_raw_packet_qp+0x114c/0x15e2
memcpy+0x1f/0x50
create_raw_packet_qp+0x114c/0x15e2
? create_raw_packet_qp_tis.isra.28+0x13d/0x13d
? lock_acquire+0x370/0x370
create_qp_common+0x2245/0x3b50
? destroy_qp_user.isra.47+0x100/0x100
? kasan_kmalloc+0x13d/0x170
? sched_clock_cpu+0x18/0x180
? fs_reclaim_acquire.part.15+0x5/0x30
? __lock_acquire+0xa11/0x1da0
? sched_clock_cpu+0x18/0x180
? kmem_cache_alloc_trace+0x17e/0x310
? mlx5_ib_create_qp+0x30e/0x17b0
mlx5_ib_create_qp+0x33d/0x17b0
? sched_clock_cpu+0x18/0x180
? create_qp_common+0x3b50/0x3b50
? lock_acquire+0x370/0x370
? __radix_tree_lookup+0x180/0x220
? uverbs_try_lock_object+0x68/0xc0
? rdma_lookup_get_uobject+0x114/0x240
create_qp.isra.5+0xce4/0x1e20
? ib_uverbs_ex_create_cq_cb+0xa0/0xa0
? copy_ah_attr_from_uverbs.isra.2+0xa00/0xa00
? ib_uverbs_cq_event_handler+0x160/0x160
? __might_fault+0x17c/0x1c0
ib_uverbs_create_qp+0x21b/0x2a0
? ib_uverbs_destroy_cq+0x2e0/0x2e0
ib_uverbs_write+0x55a/0xad0
? ib_uverbs_destroy_cq+0x2e0/0x2e0
? ib_uverbs_destroy_cq+0x2e0/0x2e0
? ib_uverbs_open+0x760/0x760
? futex_wake+0x147/0x410
? check_prev_add+0x1680/0x1680
? do_futex+0x3d3/0xa60
? sched_clock_cpu+0x18/0x180
__vfs_write+0xf7/0x5c0
? ib_uverbs_open+0x760/0x760
? kernel_read+0x110/0x110
? lock_acquire+0x370/0x370
? __fget+0x264/0x3b0
vfs_write+0x18a/0x460
SyS_write+0xc7/0x1a0
? SyS_read+0x1a0/0x1a0
? trace_hardirqs_on_thunk+0x1a/0x1c
entry_SYSCALL_64_fastpath+0x18/0x85
RIP: 0033:0x4477b9
RSP: 002b:00007f1822cadc18 EFLAGS: 00000292 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000005 RCX: 00000000004477b9
RDX: 0000000000000070 RSI: 000000002000a000 RDI: 0000000000000005
RBP: 0000000000708000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000292 R12: 00000000ffffffff
R13: 0000000000005d70 R14: 00000000006e6e30 R15: 0000000020010ff0
Allocated by task 549:
__kmalloc+0x15e/0x340
kvmalloc_node+0xa1/0xd0
create_user_qp.isra.46+0xd42/0x1610
create_qp_common+0x2e63/0x3b50
mlx5_ib_create_qp+0x33d/0x17b0
create_qp.isra.5+0xce4/0x1e20
ib_uverbs_create_qp+0x21b/0x2a0
ib_uverbs_write+0x55a/0xad0
__vfs_write+0xf7/0x5c0
vfs_write+0x18a/0x460
SyS_write+0xc7/0x1a0
entry_SYSCALL_64_fastpath+0x18/0x85
Freed by task 368:
kfree+0xeb/0x2f0
kernfs_fop_release+0x140/0x180
__fput+0x266/0x700
task_work_run+0x104/0x180
exit_to_usermode_loop+0xf7/0x110
syscall_return_slowpath+0x298/0x370
entry_SYSCALL_64_fastpath+0x83/0x85
The buggy address belongs to the object at ffff880066b99180 which
belongs to the cache kmalloc-512 of size 512 The buggy address is
located 272 bytes inside of 512-byte region [ffff880066b99180,
ffff880066b99380) The buggy address belongs to the page:
page:000000006040eedd count:1 mapcount:0 mapping: (null)
index:0x0 compound_mapcount: 0
flags: 0x4000000000008100(slab|head)
raw: 4000000000008100 0000000000000000 0000000000000000 0000000180190019
raw: ffffea00019a7500 0000000b0000000b ffff88006c403080 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff880066b99180: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff880066b99200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff880066b99280: 00 00 fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff880066b99300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff880066b99380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Cc: syzkaller <syzkaller@googlegroups.com>
Fixes: 0fb2ed66a1 ("IB/mlx5: Add create and destroy functionality for Raw Packet QP")
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that building with W=1 causes the following warning to appear:
drivers/infiniband/hw/hfi1/qp.c:484: warning: Cannot understand * on line 484 - I thought it was a doc line
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The original commit of this patch has a munged log message that is
missing several of the tags the original author intended to be on the
patch. This was due to patchworks misinterpreting a cut-n-paste
separator line as an end of message line and munging the mbox that was
used to import the patch:
https://patchwork.kernel.org/patch/10264089/
The original patch will be reapplied with a fixed commit message so the
proper tags are applied.
This reverts commit aa0de36a40.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Zero out the fields of the struct ib_pd for user mode pds so that
users querying pds via nldev will not get garbage. For simplicity,
use kzalloc() to allocate the mlx4_ib_pd struct.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Setting iova, length, and page_size allows this information to be
seen via NLDEV netlink queries, which can aid in user rdma debugging.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Some of the struct ib_mr fields weren't getting initialized. This was
benign, but will cause problems when dumping the mr resource via
nldev/restrack.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Implement RDMA nldev netlink interface to get detailed CM_ID information.
Because cm_id's are attached to rdma devices in various work queue
contexts, the pid and task information at restrak_add() time is sometimes
not useful. For example, an nvme/f host connection cm_id ends up being
bound to a device in a work queue context and the resulting pid at attach
time no longer exists after connection setup. So instead we mark all
cm_id's created via the rdma_ucm as "user", and all others as "kernel".
This required tweaking the restrack code a little. It also required
wrapping some rdma_cm functions to allow passing the module name string.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Move struct rdma_id_private to a new header cma_priv.h so the resource
tracking services in core/nldev.c can read useful information about cm_ids.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Create a common dumpit function that can be used by all common resource
types. This reduces code replication and simplifies the code as we add
more resource types.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Simplify res_to_dev() to make it easier to read/maintain.
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This struct is involved in the user API for mlx4 and should not be hidden
inside a driver header file.
Fixes: 09d208b258 ("IB/mlx4: Add report for RSS capabilities by vendor channel")
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
mlx5-updates-2018-02-28-1 (IPSec-1)
This series consists of some fixes and refactors for the mlx5 drivers,
especially around the FPGA and flow steering. Most of them are trivial
fixes and are the foundation of allowing IPSec acceleration from user-space.
We use flow steering abstraction in order to accelerate IPSec packets.
When a user creates a steering rule, [s]he states that we'll carry an
encrypt/decrypt flow action (using a specific configuration) for every
packet which conforms to a certain match. Since currently offloading these
packets is done via FPGA, we'll add another set of flow steering ops.
These ops will execute the required FPGA commands and then call the
standard steering ops.
In order to achieve this, we need that the commands will get all the
required information. Therefore, we pass the fte object and embed the
flow_action struct inside the fte. In addition, we add the shim layer
that will later be used for alternating between the standard and the
FPGA steering commands.
Some fixes, like " net/mlx5e: Wait for FPGA command responses with a timeout"
are very relevant for user-space applications, as these applications could
be killed, but we still want to wait for the FPGA and update the kernel's
database.
Regards,
Aviad and Matan
Signed-off-by: Doug Ledford <dledford@redhat.com>
The function rxe_init_device_param always return 0. So the function
type is changed to void.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In the function rxe_send, the variable rxe is not used in it.
So it should be removed.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In send_atomic_ack function, it is not necessary to make a
skb_clone. To gain better performance (high throughput and
low latency), this skb_clone is removed.
The following tests are made.
server client
--------- ---------
|1.1.1.1|<----rxe-channel--->|1.1.1.2|
--------- ---------
On server: rping -s -a 1.1.1.1 -v -C 1000 -S 512
On client: rping -c -a 1.1.1.1 -v -C 1000 -S 512
The kernel config CONFIG_DEBUG_KMEMLEAK is enabled on both server
and client.
This test runs for several hours. There is no memory leak and the whole
system can work well.
Based on the above network, the following tests are made.
Server: ibv_rc_pingpong -d rxe0 -g 1
Client: ibv_rc_pingpong -d rxe0 -g 1 1.1.1.1
The test results on Server(10 tests are made).
Before:
Throughput is 137.07 Mbit/sec
Latency is 517.76 usec/iter
After:
Throughput is 148.85 Mbit/sec
Latency is 476.64 usec/iter
The throughput is enhanced and the latency is reduced.
CC: Srinivas Eeda <srinivas.eeda@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add a parameter for configuring the port on which the ib_srpt driver
listens for incoming RDMA/CM connections, namely
/sys/kernel/config/target/srpt/discovery_auth/rdma_cm_port. The default
value for this parameter is 0 which means "do not listen for incoming
RDMA/CM connections". Add RDMA/CM support to all code that handles
connection state changes. Modify srpt_init_nodeacl() such that ACLs can
be configured for IPv4 and IPv6 addresses.
Note: incoming connection requests are only accepted for ports that
have been enabled. See also the "if (!sport->enabled)" code in the
connection request handler. See also the following configfs attribute:
/sys/kernel/config/target/srpt/$port/$port/enable.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This series consists of some fixes and refactors for the mlx5 drivers,
especially around the FPGA and flow steering. Most of them are trivial
fixes and are the foundation of allowing IPSec acceleration from user-space.
We use flow steering abstraction in order to accelerate IPSec packets.
When a user creates a steering rule, [s]he states that we'll carry an
encrypt/decrypt flow action (using a specific configuration) for every
packet which conforms to a certain match. Since currently offloading these
packets is done via FPGA, we'll add another set of flow steering ops.
These ops will execute the required FPGA commands and then call the
standard steering ops.
In order to achieve this, we need that the commands will get all the
required information. Therefore, we pass the fte object and embed the
flow_action struct inside the fte. In addition, we add the shim layer
that will later be used for alternating between the standard and the
FPGA steering commands.
Some fixes, like " net/mlx5e: Wait for FPGA command responses with a timeout"
are very relevant for user-space applications, as these applications could
be killed, but we still want to wait for the FPGA and update the kernel's
database.
Regards,
Aviad and Matan
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJan4UmAAoJEEg/ir3gV/o+cZwH/1xBpdLsmeqEimwQ41bAc9Rj
UmPZXXMyQVUYfGOiE1aLTH7YNi38XWSnTFMN7HklMeX/9YKxUZNG8YuiO9iQhE1B
rUqRKfYFz9oFrUh95SzeclaunTpKrhYKHjQ9/u9nBMfI3H2Fy+y2NUBjIqJ6nysz
op3EwRcX5kD4+MjRum24XLUnMSYbg05mHCZKTDj5/2T4x+/j0XQqvvmWWinIt8BO
R4d7XGGywGjbhtcG1j+XBcFeLsEZnS/w70hoN38TdcmNWvokl1pGk8DVDii9i7GX
c5jQj2h5WG/bdsS26y8MFfWpoAn3Qzzm4W4OYwp/vmL7n/Llvq0GRCEKCi8AlA0=
=LeYV
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-02-28-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-02-28-1 (IPSec-1)
This series consists of some fixes and refactors for the mlx5 drivers,
especially around the FPGA and flow steering. Most of them are trivial
fixes and are the foundation of allowing IPSec acceleration from user-space.
We use flow steering abstraction in order to accelerate IPSec packets.
When a user creates a steering rule, [s]he states that we'll carry an
encrypt/decrypt flow action (using a specific configuration) for every
packet which conforms to a certain match. Since currently offloading these
packets is done via FPGA, we'll add another set of flow steering ops.
These ops will execute the required FPGA commands and then call the
standard steering ops.
In order to achieve this, we need that the commands will get all the
required information. Therefore, we pass the fte object and embed the
flow_action struct inside the fte. In addition, we add the shim layer
that will later be used for alternating between the standard and the
FPGA steering commands.
Some fixes, like " net/mlx5e: Wait for FPGA command responses with a timeout"
are very relevant for user-space applications, as these applications could
be killed, but we still want to wait for the FPGA and update the kernel's
database.
Regards,
Aviad and Matan
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The QP state is limited and declared in enum ib_qp_state,
but ucma user was able to supply any possible (u32) value.
Reported-by: syzbot+0df1ab766f8924b1edba@syzkaller.appspotmail.com
Fixes: 7521663857 ("RDMA/cma: Export rdma cm interface to userspace")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The user can provide very large cqe_size which will cause to integer
overflow as it can be seen in the following UBSAN warning:
Signed-off-by: Doug Ledford <dledford@redhat.com>
Users of ucma are supposed to provide size of option level,
in most paths it is supposed to be equal to u8 or u16, but
it is not the case for the IB path record, where it can be
multiple of struct ib_path_rec_data.
This patch takes simplest possible approach and prevents providing
values more than possible to allocate.
Reported-by: syzbot+a38b0e9f694c379ca7ce@syzkaller.appspotmail.com
Fixes: 7ce86409ad ("RDMA/ucma: Allow user space to set service type")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
resolved_dev returned might be NULL as ifindex is transient number.
Ignoring NULL check of resolved_dev might crash the kernel.
Therefore perform NULL check before accessing resolved_dev.
Additionally rdma_resolve_ip_route() invokes addr_resolve() which
performs check and address translation for loopback ifindex.
Therefore, checking it again in rdma_resolve_ip_route() is not helpful.
Therefore, the code is simplified to avoid IFF_LOOPBACK check.
Fixes: 200298326b ("IB/core: Validate route when we init ah")
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add helper functions that check if a protocol is
part of a flow steering match criteria.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The has_tag member will indicate whether a tag action was specified
in flow specification.
A flow tag 0 = MLX5_FS_DEFAULT_FLOW_TAG is assumed a valid flow tag
that is currently used by mlx5 RDMA driver, whereas in HW flow_tag = 0
means that the user doesn't care about flow_tag. HW always provide
a flow_tag = 0 if all flow tags requested on a specific flow are 0.
So we need a way (in the driver) to differentiate between a user really
requesting flow_tag = 0 and a user who does not care, in order to be
able to report conflicting flow tags on a specific flow.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Group and pass all function arguments of parse_flow_attr call in one
common struct mlx5_flow_act.
This patch passes all the action arguments of parse_flow_attr in one common
struct mlx5_flow_act. It allows us to scale the number of actions without adding
new arguments to the function.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Hitting the following hardlockup due to a race condition in
error CQE processing.
[26146.879798] bnxt_en 0000:04:00.0: QPLIB: FP: CQ Processed Req
[26146.886346] bnxt_en 0000:04:00.0: QPLIB: wr_id[1251] = 0x0 with status 0xa
[26156.350935] NMI watchdog: Watchdog detected hard LOCKUP on cpu 4
[26156.357470] Modules linked in: nfsd auth_rpcgss nfs_acl lockd grace
[26156.447957] CPU: 4 PID: 3413 Comm: kworker/4:1H Kdump: loaded
[26156.457994] Hardware name: Dell Inc. PowerEdge R430/0CN7X8,
[26156.466390] Workqueue: ib-comp-wq ib_cq_poll_work [ib_core]
[26156.472639] Call Trace:
[26156.475379] <NMI> [<ffffffff98d0d722>] dump_stack+0x19/0x1b
[26156.481833] [<ffffffff9873f775>] watchdog_overflow_callback+0x135/0x140
[26156.489341] [<ffffffff9877f237>] __perf_event_overflow+0x57/0x100
[26156.496256] [<ffffffff98787c24>] perf_event_overflow+0x14/0x20
[26156.502887] [<ffffffff9860a580>] intel_pmu_handle_irq+0x220/0x510
[26156.509813] [<ffffffff98d16031>] perf_event_nmi_handler+0x31/0x50
[26156.516738] [<ffffffff98d1790c>] nmi_handle.isra.0+0x8c/0x150
[26156.523273] [<ffffffff98d17be8>] do_nmi+0x218/0x460
[26156.528834] [<ffffffff98d16d79>] end_repeat_nmi+0x1e/0x7e
[26156.534980] [<ffffffff987089c0>] ? native_queued_spin_lock_slowpath+0x1d0/0x200
[26156.543268] [<ffffffff987089c0>] ? native_queued_spin_lock_slowpath+0x1d0/0x200
[26156.551556] [<ffffffff987089c0>] ? native_queued_spin_lock_slowpath+0x1d0/0x200
[26156.559842] <EOE> [<ffffffff98d083e4>] queued_spin_lock_slowpath+0xb/0xf
[26156.567555] [<ffffffff98d15690>] _raw_spin_lock+0x20/0x30
[26156.573696] [<ffffffffc08381a1>] bnxt_qplib_lock_buddy_cq+0x31/0x40 [bnxt_re]
[26156.581789] [<ffffffffc083bbaa>] bnxt_qplib_poll_cq+0x43a/0xf10 [bnxt_re]
[26156.589493] [<ffffffffc083239b>] bnxt_re_poll_cq+0x9b/0x760 [bnxt_re]
The issue happens if RQ poll_cq or SQ poll_cq or Async error event tries to
put the error QP in flush list. Since SQ and RQ of each error qp are added
to two different flush list, we need to protect it using locks of
corresponding CQs. Difference in order of acquiring the lock in
SQ poll_cq and RQ poll_cq can cause a hard lockup.
Revisits the locking strategy and removes the usage of qplib_cq.hwq.lock.
Instead of this lock, introduces qplib_cq.flush_lock to handle
addition/deletion of QPs in flush list. Also, always invoke the flush_lock
in order (SQ CQ lock first and then RQ CQ lock) to avoid any potential
deadlock.
Other than the poll_cq context, the movement of QP to/from flush list can
be done in modify_qp context or from an async error event from HW.
Synchronize these operations using the bnxt_re verbs layer CQ locks.
To achieve this, adds a call back to the HW abstraction layer(qplib) to
bnxt_re ib_verbs layer in case of async error event. Also, removes the
buddy cq functions as it is no longer required.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Fix warning limit for kernel stack consumption:
drivers/infiniband/core/cq.c: In function 'ib_process_cq_direct':
drivers/infiniband/core/cq.c:78:1: error: the frame size of 1032 bytes
is larger than 1024 bytes [-Werror=frame-larger-than=]
Using smaller ib_wc array on the stack brings us comfortably below that
limit again.
Fixes: 246d8b184c ("IB/cq: Don't force IB_POLL_DIRECT poll context for ib_process_cq_direct")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sergey Gorenko <sergeygo@mellanox.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
"err" is either zero or possibly uninitialized here. It should be
-EINVAL.
Fixes: 427c1e7bcd ("{IB, net}/mlx5: Move the modify QP operation table to mlx5_ib")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The series that introduced dual port RoCE mode assumed that we don't have
a dual port HCA that use the mlx5 driver, this is not the case for
Connect-IB HCAs. This reasoning led to assigning 1 as the native port
index which causes issue when the second port is used.
For example query_pkey() when called on the second port will return values
of the first port. Make sure that we assign the right port index as the
native port index.
Fixes: 32f69e4be2 ("{net, IB}/mlx5: Manage port association for multiport RoCE")
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The commit cited below added a gid_type field (RoCEv1 or RoCEv2)
to GID properties.
When adding GIDs, this gid_type field was copied over to the
hardware gid table. However, when deleting GIDs, the gid_type field
was not copied over to the hardware gid table.
As a result, when running RoCEv2, all RoCEv2 gids in the
hardware gid table were set to type RoCEv1 when any gid was deleted.
This problem would persist until the next gid was added (which would again
restore the gid_type field for all the gids in the hardware gid table).
Fix this by copying over the gid_type field to the hardware gid table
when deleting gids, so that the gid_type of all remaining gids is
preserved when a gid is deleted.
Fixes: b699a859d1 ("IB/mlx4: Add gid_type to GID properties")
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When using IPv4 addresses in RoCEv2, the GID format for the mapped
IPv4 address should be: ::ffff:<4-byte IPv4 address>.
In the cited commit, IPv4 mapped IPV6 addresses had the 3 upper dwords
zeroed out by memset, which resulted in deleting the ffff field.
However, since procedure ipv6_addr_v4mapped() already verifies that the
gid has format ::ffff:<ipv4 address>, no change is needed for the gid,
and the memset can simply be removed.
Fixes: 7e57b85c44 ("IB/mlx4: Add support for setting RoCEv2 gids in hardware")
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
iWARP does not support RDMA WRITE or SEND with immediate data.
Driver should check this before submitting to FW and return an
immediate error
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Race in qedr_poll_cq, lastest_cqe wasn't protected by lock,
leading to a case where two context's accessing poll_cq at
the same time lead to one of them having a pointer to an old
latest_cqe and reading an invalid cqe element
Signed-off-by: Amit Radzi <Amit.Radzi@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Fix iWARP connect and listen to use the mapped port for
ipv4 and ipv6. Without this fixed, running on a server
that has iwpmd enabled will not use the correct port
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The wrong parameter was passed to dst_neigh_lookup
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
If a HCA supports the SG_GAPS_REG feature then fewer memory regions
are required per command. This patch reduces the number of memory
regions that is allocated per SRP session.
Signed-off-by: Sergey Gorenko <sergeygo@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Acked-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch avoids that sparse reports the following:
drivers/infiniband/hw/hfi1/driver.c:251:13: warning: context imbalance in 'rcv_hdrerr' - different lock contexts for basic block
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Continue at the bottom of a loop are removed.
Issue found using drop_continue.cocci Coccinelle script.
Signed-off-by: Arushi Singhal <arushisinghal19971997@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Storage ULPs (like NVMEoF) benefit from exposing affinity mapping
per completion vector to find the optimal multi-queue affinity
assignments. The ULPs call the verbs API ib_get_vector_affinity
introduced in commit c66cd353bb ("RDMA/core: expose affinity mappings per
completion vector") to get the underlying devices affinity mappings.
Add support in driver to expose the affinity masks per MSI-X
completion vector.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Currently all CM nodes involved in a connection are
maintained in a connected_node list per dev. During
connection setup, we need to search this every time
we receive a packet on the iWARP LAN Queue (ILQ) and
this can be pretty inefficient for large number of
connections.
Fix this by organizing the CM nodes in two lists -
accelerated list and non-accelerated list. The search
on ILQ receive would be limited to only non accelerated
nodes. When a node moves to RTS, it is added to the
accelerated list.
Benchmarking ucmatose 16k connections shows a 20%
improvement in test completion time.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Currently the TX pending lists for IEQ and ILQ are
handled separately. The handling of both can be
consolidated in i40iw_poll_completion.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The pointer rdi is being initialized with a value that is never read
and re-assigned immediately after, hence the initialization is redundant
and can be removed.
Cleans up clang warning:
drivers/infiniband/sw/rdmavt/vt.c:94:23: warning: Value stored to 'rdi'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
IPv6 does path selection for multipath routes deep in the lookup
functions. The next patch adds L4 hash option and needs the skb
for the forward path. To get the skb to the relevant FIB lookup
functions it needs to go through the fib rules layer, so add a
lookup_data argument to the fib_lookup_arg struct.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note: This is compile only tested as I have no access to the hw. This
variable was not used anywhere in the code. Removing it saves 24 bytes.
add/remove: 0/1 grow/shrink: 0/0 up/down: 0/-24 (-24)
Function old new delta
rxe_qp_state_name 24 - -24
Total: Before=3348732, After=3348708, chg -0.00%
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Note: This is compile only tested as I have no access to the hw.
This variable was not used in qib_sdma.c but in qib_iba7322.c. Declaring it
there, as static, saves 56 bytes.
add/remove: 0/2 grow/shrink: 0/0 up/down: 0/-144 (-144)
Function old new delta
qib_sdma_state_names 56 - -56
qib_sdma_event_names 88 - -88
Total: Before=2874565, After=2874421, chg -0.01%
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Note: This is compile only tested as I have no access to the hw.
This variable was not used anywhere in the code. Removing it saves 88
bytes.
add/remove: 0/1 grow/shrink: 0/0 up/down: 0/-88 (-88)
Function old new delta
qib_sdma_event_names 88 - -88
Total: Before=2874565, After=2874477, chg -0.00%
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Except for a minor log message change, this patch does not change
any functionality. For the introduction of %pIS, see also commit
1067964305 ("lib: vsprintf: add IPv4/v6 generic %p[Ii]S[pfs]
format specifier").
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The caller of srp_ib_lookup_path() is responsible for holding a reference
on the SCSI host. That means that commit 8a0d18c621 was not necessary.
Hence revert it.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Before commit e494f6a728 ("[SCSI] improved eh timeout handler") it
did not really matter whether or not abort handlers like srp_abort()
called .scsi_done() when returning another value than SUCCESS. Since
that commit however this matters. Hence only call .scsi_done() when
returning SUCCESS.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
On 32-bit targets, we otherwise get a warning about an impossible constant
integer expression:
In file included from include/linux/kernel.h:11,
from include/linux/interrupt.h:6,
from drivers/infiniband/hw/bnxt_re/ib_verbs.c:39:
drivers/infiniband/hw/bnxt_re/ib_verbs.c: In function 'bnxt_re_query_device':
include/linux/bitops.h:7:24: error: left shift count >= width of type [-Werror=shift-count-overflow]
#define BIT(nr) (1UL << (nr))
^~
drivers/infiniband/hw/bnxt_re/bnxt_re.h:61:34: note: in expansion of macro 'BIT'
#define BNXT_RE_MAX_MR_SIZE_HIGH BIT(39)
^~~
drivers/infiniband/hw/bnxt_re/bnxt_re.h:62:30: note: in expansion of macro 'BNXT_RE_MAX_MR_SIZE_HIGH'
#define BNXT_RE_MAX_MR_SIZE BNXT_RE_MAX_MR_SIZE_HIGH
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/infiniband/hw/bnxt_re/ib_verbs.c:149:25: note: in expansion of macro 'BNXT_RE_MAX_MR_SIZE'
ib_attr->max_mr_size = BNXT_RE_MAX_MR_SIZE;
^~~~~~~~~~~~~~~~~~~
Fixes: 872f357824 ("RDMA/bnxt_re: Add support for MRs with Huge pages")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Building for a 32-bit target results in a couple of warnings from casting
between a 32-bit pointer and a 64-bit integer:
drivers/infiniband/hw/bnxt_re/qplib_fp.c: In function 'bnxt_qplib_service_nq':
drivers/infiniband/hw/bnxt_re/qplib_fp.c:333:23: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
bnxt_qplib_arm_srq((struct bnxt_qplib_srq *)q_handle,
^
drivers/infiniband/hw/bnxt_re/qplib_fp.c:336:12: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
(struct bnxt_qplib_srq *)q_handle,
^
In file included from include/linux/byteorder/little_endian.h:5,
from arch/arm/include/uapi/asm/byteorder.h:22,
from include/asm-generic/bitops/le.h:6,
from arch/arm/include/asm/bitops.h:342,
from include/linux/bitops.h:38,
from include/linux/kernel.h:11,
from include/linux/interrupt.h:6,
from drivers/infiniband/hw/bnxt_re/qplib_fp.c:39:
drivers/infiniband/hw/bnxt_re/qplib_fp.c: In function 'bnxt_qplib_create_srq':
include/uapi/linux/byteorder/little_endian.h:31:43: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
#define __cpu_to_le64(x) ((__force __le64)(__u64)(x))
^
include/linux/byteorder/generic.h:86:21: note: in expansion of macro '__cpu_to_le64'
#define cpu_to_le64 __cpu_to_le64
^~~~~~~~~~~~~
drivers/infiniband/hw/bnxt_re/qplib_fp.c:569:19: note: in expansion of macro 'cpu_to_le64'
req.srq_handle = cpu_to_le64(srq);
Using a uintptr_t as an intermediate works on all architectures.
Fixes: 37cb11acf1 ("RDMA/bnxt_re: Add SRQ support for Broadcom adapters")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Perform QP type check in one place and fail as early as possible.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Maintaining the uobjects list is mandatory, hoist it into the common
rdma_alloc_commit_uobject() function and inline it as there is now
only one caller.
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Release the netdev references in the cleanup path. Invokes the cleanup
routines if bnxt_re_ib_reg fails.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
To support host systems with non 4K page size, l2_db_size shall be
calculated with 4096 instead of PAGE_SIZE. Also, supply the host page size
to FW during initialization.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
HW requires an unconditonal fence for all non-wire memory operations
through SQ. This guarantees the completions of these memory operations.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
During IB device registration process, if query_device() fails or if
ib_core fails to registers sysfs entries, rdma cgroup cleanup is
skipped.
Cc: <stable@vger.kernel.org> # v4.2+
Fixes: 4be3a4fa51 ("IB/core: Fix kernel crash during fail to initialize device")
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
IB spec says that a lid should be ignored when link layer is Ethernet,
for example when building or parsing a CM request message (CA17-34).
However, since ib_lid_be16() and ib_lid_cpu16() validates the slid,
not only when link layer is IB, we set the slid to zero to prevent
false warnings in the kernel log.
Fixes: 62ede77799 ("Add OPA extended LID support")
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
All other mlx5_events report the port number as 1 based, which is how FW
reports it in the port event EQE. Reporting 0 for this event causes
mlx5_ib to not raise a fatal event notification to registered clients
due to a seemingly invalid port.
All switch cases in mlx5_ib_event that go through the port check are
supposed to set the port now, so just do it once at variable
declaration.
Fixes: 89d44f0a6c73("net/mlx5_core: Add pci error handlers to mlx5_core driver")
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
During QP creation, the mlx5 driver translates the QP type to an
internal value which is passed on to FW. There was no check to make
sure that the translated value is valid, and -EINVAL was coerced into
the mailbox command.
Current firmware refuses this as an invalid QP type, but future/past
firmware may do something else.
Fixes: 09a7d9eca1 ('{net,IB}/mlx5: QP/XRCD commands via mlx5 ifc')
Reviewed-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
From: Mark Bloch <markb@mellanox.com>
=========
Add IB representor when in switchdev mode
The following series adds support for an IB (RAW Ethernet only) device
representor which is created when the user switches to switchdev mode.
Today when switching to switchdev mode the only representors which are
created are net devices. Each netdev is a representor of a virtual
function and any data sent via the representor is received on the virtual
function, and any data sent via the virtual function is received by the
representor.
For the mlx5 driver the main use of this functionality is to be able to
use Open vSwitch on the hypervisor in order to manage/control traffic
from/to the virtual functions. Open vSwitch can also work with DPDK
devices and not just net devices, this series exposes an IB device, which
Mellanox PMD driver uses, which then can be used by Open vSwitch DPDK.
An IB device representor exposes only RAW Ethernet QP capabilities and
the ability to create flow rules to direct traffic to its RX queues. The
state of the IB device (ACTIVE/DOWN etc..) is based on the state of the
corresponding net device representor. No other RDMA/RoCE functionality is
currently supported and no GID table is exposed.
=========
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJakH7zAAoJEEg/ir3gV/o+c/MIAMGGgNajr49+JP3t9wnrs011
+cTfAfM88HBzTlfb/COEBz+jurH2oB7ZF4RZC29S+6pR3loKKBuvbiPndE0XKjSg
Ue4sOkawybmDvfo9ZiMsusOiMfTp5wsLmqJP1HRUvGMAlSBeriMTZfbiKzx5c3Ok
X8cMnRIvUOtCoQaJTfKarDUn4OF8aFam4tQW8k/RAo77kTPyihb1NlGiblrcCA2E
PWYAOWW3D8gvE0cr19JVgEqpKIaJ/VRyjwQ7m8XSvfBJtw1ZTO6YMXiXbWMOsRzD
fx33H+n/qwJT0cnxDmSpZrR7mEk+Wr2HL92O85KDupOSgLOIlywmtIIkEAnCeaw=
=Fq6m
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-02-23' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux into k.o/wip/dl-for-next
mlx5-update-2018-02-23 (IB representors)
From: Mark Bloch <markb@mellanox.com>
=========
Add IB representor when in switchdev mode
The following series adds support for an IB (RAW Ethernet only) device
representor which is created when the user switches to switchdev mode.
Today when switching to switchdev mode the only representors which are
created are net devices. Each netdev is a representor of a virtual
function and any data sent via the representor is received on the virtual
function, and any data sent via the virtual function is received by the
representor.
For the mlx5 driver the main use of this functionality is to be able to
use Open vSwitch on the hypervisor in order to manage/control traffic
from/to the virtual functions. Open vSwitch can also work with DPDK
devices and not just net devices, this series exposes an IB device, which
Mellanox PMD driver uses, which then can be used by Open vSwitch DPDK.
An IB device representor exposes only RAW Ethernet QP capabilities and
the ability to create flow rules to direct traffic to its RX queues. The
state of the IB device (ACTIVE/DOWN etc..) is based on the state of the
corresponding net device representor. No other RDMA/RoCE functionality is
currently supported and no GID table is exposed.
=========
Signed-off-by: Doug Ledford <dledford@redhat.com>
From: Mark Bloch <markb@mellanox.com>
=========
Add IB representor when in switchdev mode
The following series adds support for an IB (RAW Ethernet only) device
representor which is created when the user switches to switchdev mode.
Today when switching to switchdev mode the only representors which are
created are net devices. Each netdev is a representor of a virtual
function and any data sent via the representor is received on the virtual
function, and any data sent via the virtual function is received by the
representor.
For the mlx5 driver the main use of this functionality is to be able to
use Open vSwitch on the hypervisor in order to manage/control traffic
from/to the virtual functions. Open vSwitch can also work with DPDK
devices and not just net devices, this series exposes an IB device, which
Mellanox PMD driver uses, which then can be used by Open vSwitch DPDK.
An IB device representor exposes only RAW Ethernet QP capabilities and
the ability to create flow rules to direct traffic to its RX queues. The
state of the IB device (ACTIVE/DOWN etc..) is based on the state of the
corresponding net device representor. No other RDMA/RoCE functionality is
currently supported and no GID table is exposed.
=========
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJakH7zAAoJEEg/ir3gV/o+c/MIAMGGgNajr49+JP3t9wnrs011
+cTfAfM88HBzTlfb/COEBz+jurH2oB7ZF4RZC29S+6pR3loKKBuvbiPndE0XKjSg
Ue4sOkawybmDvfo9ZiMsusOiMfTp5wsLmqJP1HRUvGMAlSBeriMTZfbiKzx5c3Ok
X8cMnRIvUOtCoQaJTfKarDUn4OF8aFam4tQW8k/RAo77kTPyihb1NlGiblrcCA2E
PWYAOWW3D8gvE0cr19JVgEqpKIaJ/VRyjwQ7m8XSvfBJtw1ZTO6YMXiXbWMOsRzD
fx33H+n/qwJT0cnxDmSpZrR7mEk+Wr2HL92O85KDupOSgLOIlywmtIIkEAnCeaw=
=Fq6m
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-02-23' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
mlx5-update-2018-02-23 (IB representors)
From: Mark Bloch <markb@mellanox.com>
=========
Add IB representor when in switchdev mode
The following series adds support for an IB (RAW Ethernet only) device
representor which is created when the user switches to switchdev mode.
Today when switching to switchdev mode the only representors which are
created are net devices. Each netdev is a representor of a virtual
function and any data sent via the representor is received on the virtual
function, and any data sent via the virtual function is received by the
representor.
For the mlx5 driver the main use of this functionality is to be able to
use Open vSwitch on the hypervisor in order to manage/control traffic
from/to the virtual functions. Open vSwitch can also work with DPDK
devices and not just net devices, this series exposes an IB device, which
Mellanox PMD driver uses, which then can be used by Open vSwitch DPDK.
An IB device representor exposes only RAW Ethernet QP capabilities and
the ability to create flow rules to direct traffic to its RX queues. The
state of the IB device (ACTIVE/DOWN etc..) is based on the state of the
corresponding net device representor. No other RDMA/RoCE functionality is
currently supported and no GID table is exposed.
=========
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations just create and destroy IDR.
So, we mark them as async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When in switchdev mode, there is no need to do self loopback checks
as we can't receive those packets, we insert steering rules to the
eswitch that make sure packets can't be looped back.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This commit adds full support for IB representor:
1) Representors profile, We add two new profiles:
nic_rep_profile - This profile will be used to create an IB device that
represents the PF/UPLINK.
rep_profile - This profile will be used to create an IB device that
represents VFs. Each VF will be its own representor.
2) Proper load/unload callbacks, Those are called by the E-Switch when
moving to/from switchdev mode.
3) Different flow DB handling for when we in switchdev mode.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In order to forward traffic from representor's SQ to the right virtual
function, every time an SQ is created also add the corresponding flow rule
to the FDB.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When enabling many VFs and switching to switchdev mode, the total amount
of mkeys we try to allocate when loading representors is very large and
may cause timeouts on allocations, the same issues was observed on VFs
and we employ the same fix that was done for them. We avoid allocating
the full MR cache on load but still allow it to be manipulated once the
IB device is loaded.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently in switchdev mode we allow only for raw packet QPs.
Expose the right capabilities and set the gid table length to 0, also
make sure we don't try to enable RoCE, so split the function
to enable RoCE so representors can enable only the notifier needed for
net device events.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently we listen to netdev register/unregister event based on PCI
device. When in switchdev mode PF and representors share the same PCI
device, so in order to pair ib device and netdev in switchdev mode
compare the netdev that triggered the event to that of the representor.
Expose a function that lets you receive the netdev associated what
a given representor.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When we point to a representor, it means we are in switchdev mode.
The flow db is shared between PF and virtual function representors
so each rule created needs to have a match on its specific source port.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
A flow DB is a shared resource between PF and representors,
need to allocate it only when creating the PF IB device.
Once we add IB representors, they will use the flow db which was
created by the PF.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Create the basic infrastructure of registering and unregistering
IB representors. The load/unload callbacks are left empty and
proper implementation will be introduced in following patches.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The proper return error is -EOPNOTSUPP and not -ENOSYS, so update
all places in verbs.c to match this semantics.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Simplify the code by directly checking the availability of extended
command flog instead of doing multiple shift operations.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The internal to kernel variable declarations don't need to be
declared with user types. This patch converts such occurrences
appeared in ib_uverbs_write().
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Move all header validation logic to be performed before SRCU read lock.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
