Not all supported boards will require a MMCI gpio-regulator,
therefore it's a good idea to only enable the node when and if
it is required. Let's disable it by default.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is a very simple mechanism to change and SDI's voltage which
consists of toggling some GPIOs. This scenario can be better handled
if we convert it to a GPIO regulator. This patch provides one which
can be read from Device Tree.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In the DB8500 Reference Manual SDI devices are described as being
part of peripheral blocks. This is more in line with how these devices
are actually represented in hardware, so here we detail which
peripheral block each of the SDI devices belong in the node name.
Requested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Regulator supply names should be allocated by board rather than
per SoC, as the same SoC could be wired differently on varying
hardware. Here we push all regulator-name allocation out to the
dbx5x0 subordinate board files; HREF and Snowball.
Requested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here we fix a simple copy and paste error and bring some node
spaces back into line with the remainder of the tree.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now the Nomadik I2C driver has been converted to an AMBA one, we
are required to provide the Primecell IDs via platform code. When
booting with DT enabled these have to be specified in the device
nodes. We do that here.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
SSP won't probe unless the specified register address format
is correct i.e. we have to specify that the address is in hex.
After this patch has been applied, the SSP (SPI) driver probes
as expected.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch inserts all known MSP devices into the DBx5x0 Device Tree
disabled and enables the two important ones for the Snowball low-cost
development board.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Ensure correct probing and pass though important configuration
options to the AB8500 CODEC driver when DT is enabled
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since initial support was provided for the Nomadik I2C driver, it
has been converted to an AMBA device. AMBA devices are probed in
a slightly different way to other devices, so we have to identify
them using an "arm,primecell" compatible string. As well as doing
just that, this patch specifies which regulators the controller
should use and requests a clock-speed. The latter is provided as
more of an example, as it's the same as the recently changed
default configuration.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The compatible string found in the Power-On-Key's MFD cell matches
the device name provided in the driver. Keeping this naming convention
seems like a good idea, so we're changing the one found in the DTS
file to match.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It's understood that the AB8500 should be subordinate to the DB8500;
however, the AB8500 uses the GIC as it's interrupt controller. If
we do not specify which IRQ controller to use the default is to use
the next encountered IRQ controller as we climb the tree. This would
be the DB8500. This patch ensures the AB8500 makes use of the correct
interrupt controller.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We're just about to provide the DB8500-PRCMU with its own IRQ domain,
so that its subordinate drivers can use it as an interrupt controller.
It's obligatory for all IRQ controllers to reference themselves as
such from its own node in Device Tree. This patch does just that.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
