hdc100x supports Texas Instruments HDC1000 and HDC1008 relative
humidity and temperature sensors. Add these product names to
Kconfig.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace the i2c_smbus_read_byte commmands used to retrieve the sensor
data with an i2c_master_recv command.
The smbus read byte method fails because the device does not expect a
stop condition after sending the first byte. When we issue the second
read, we are getting the first byte again. Net effect is that of the 14
bits used for the measurement, the 8 most significant bits are correct,
the lower 6 are not.
None of the smbus read protocols follow the pattern this device requires
(S Addr Rd [A] Data [A] Data NA P), hence the switch to an i2c receive
transaction.
Applicable from original introduction of this driver, but will require
backporting due to churn in the code.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Select IIO_BUFFER and IIO_TRIGGERED_BUFFER to compile.
Remove IIO_TRIGGER if present since IIO_BUFFER selects it.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the iio_pollfunc_store_time parameter during triggered buffer
set-up to get valid timestamps.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-By: Tiberiu Breana <tiberiu.a.breana@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We want the fixes in here, and we can resolve a merge issue in
drivers/iio/industrialio-trigger.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shifting sensor data to the right 2 bits was incorrect and caused the
scaling values + offsets to be invalid.
Reported-by: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Tested-by: Alison Schofield <amsfield22@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
IIO_TEMP channel was being incorrectly reported back as Celsius when it
should have been milliCelsius. This is via an incorrect scale value being
returned to userspace.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The I2C drivers have an i2c_device_id array but that information isn't
exported to the modules using the MODULE_DEVICE_TABLE() macro. So the
modules autoloading won't work if the I2C device is registered using
OF or legacy board files due missing alias information in the modules.
The issue was found using Kieran Bingham's coccinelle semantic patch:
https://lkml.org/lkml/2016/5/10/520
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We haven't taken the lock yet so we don't need to unlock here.
Fixes: 0d96d5ead3 ('iio: humidity: Add triggered buffer support for AM2315')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Apply the correct mask to enable all available humidity integration
times. Currently, the driver defaults to 6500 and all is okay with that.
However, if 3850 is selected we get a stuck bit and can't change back
to 6500 or select 2500. (Verified with HDC1008)
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Matt Ranostay <mranostay@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add basic support for the Aosong AM2315 relative humidity
and ambient temperature sensor.
Includes support for raw readings and ACPI detection.
Datasheet:
http://www.aosong.com/asp_bin/Products/en/AM2315.pdf
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* Unify log messages
* Add more DEBUG messages
Apparently this driver is working unreliably on some platforms that I can't
test. Therefore I want an easy way for bug reporters to provide useful
information without making the driver too chatty by default.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Previously most drivers that used a i2c_check_functionality() check
condition required various error codes on failure. This patchset
converts to a standard of -EOPNOTSUPP
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Wall time obtained from ktime_get_real_ns is susceptible to sudden jumps due to
user setting the time or due to NTP. Boot time is constantly increasing time
better suited for comparing two timestamps.
Signed-off-by: Abhilash Jindal <klock.android@gmail.com>
Reviewed-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for Hoperf th06 humidity and
temperature sensor as it uses same register definitions
as si7020
th06 Datasheet: http://www.hoperf.com/upload/sensor/TH06.pdf
Signed-off-by: Cristina Moraru <cristina.moraru09@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for Hoperf th02 humidity and
temperature sensor as it uses same register definitions
as si7005
th02 Datasheet: http://www.anglia-live.com/netalogue/pdfs/hrf/datasheets/TH02_V1.1.pdf
Signed-off-by: Cristina Moraru <cristina.moraru09@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The new algorithm uses a 'one size fits em all' threshold, which should
be easier to understand and debug. I believe there are no regressions
compared to the old adaptive threshold algorithm. I don't remember why
I chose the old algorithm when I initially wrote the driver.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Instead of guessing where the data starts, we now just try to decode from
every possible start position. This causes no additional overhead if we
properly received the full preamble and only costs a few extra CPU cycles
in the case where the preamble is corrupted. This is much more efficient
than to return an error to userspace and start over again.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This set does not include those for issues introduced during the merge
window. Fixes of those will follow in a future series.
* ad5064
- Make sure the local i2c_write returns 0 on success rather than the
number of bytes transfered. Otherwise we report an error on all writes.
- Fix a shift for ad5629 and ad5669 which gives incorrect DAC output on
these parts.
* ad7793
- The product ID on the datasheet is wrong. Fix it in the driver.
* IIO_DUMMY_EVGEN
- select IRQ_WORK as a dependency.
* lpc32xx
- make sure clock is prepared before enabling.
* si7020
- data byte order was reversed. Fix it.
* vf610
- Internal temperature calculation was wrong if a different
reference voltage was used. Now use a linear interpolation
function to make it work over the full range.
- Fix a division by zero in the case of a device tree property
not being present (same issue two fixes).
* xilinx XADC
- VREFN scale was wrong - fix it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=362F
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.4a' of ssh://ra.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.4 cycle.
This set does not include those for issues introduced during the merge
window. Fixes of those will follow in a future series.
* ad5064
- Make sure the local i2c_write returns 0 on success rather than the
number of bytes transfered. Otherwise we report an error on all writes.
- Fix a shift for ad5629 and ad5669 which gives incorrect DAC output on
these parts.
* ad7793
- The product ID on the datasheet is wrong. Fix it in the driver.
* IIO_DUMMY_EVGEN
- select IRQ_WORK as a dependency.
* lpc32xx
- make sure clock is prepared before enabling.
* si7020
- data byte order was reversed. Fix it.
* vf610
- Internal temperature calculation was wrong if a different
reference voltage was used. Now use a linear interpolation
function to make it work over the full range.
- Fix a division by zero in the case of a device tree property
not being present (same issue two fixes).
* xilinx XADC
- VREFN scale was wrong - fix it.
The Silicon Labs Si7013, Si7020, and Si7021 family of I2C humidity and
temperature sensors deliver 16 bit data high byte first.
See the datasheet available at:
https://www.silabs.com/Support%20Documents%2fTechnicalDocs%2fSi7020-A20.pdf
But as documented in Documentation/i2c/smbus-protocol,
i2c_smbus_read_word_data() expects the low byte first.
Change the driver to use i2c_smbus_read_word_swapped to get correct byte
order.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Previous offset wasn't applied in the correct order and invalid.
This patchset fixes this issue, and also has the correct scale value
applied to the offset.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Support for MS8607 temperature, pressure & humidity sensor.
This part is using functions from MS5637 for temperature and pressure
and HTU21 for humidity
Signed-off-by: Ludovic Tancerel <ludovic.tancerel@maplehightech.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Support for HTU21 temperature & humidity sensor
Signed-off-by: Ludovic Tancerel <ludovic.tancerel@maplehightech.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for the HDC100x temperature and humidity sensors
including the resistive heater element.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The maximum possible value for the relative humidity is 55575 (100%RH).
This value, if shifted right by 2 bits, uses 14 bits and masking it with
a 12 bit mask removes 2 meaningful bits.
The masking has been replaced with a range check that sets the minimum
value at 786 (0%RH) and the maximum at 13893 (99.998%RH).
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This cleans up the most ugly workaround in this driver. There are no
functional changes yet in the decoding algorithm, but we improve the
following things:
* Get rid of spurious warning messages on systems with fast HRTIMER.
* If the clock is not fast enough for decoding to work, we give
up immediately.
* In that case we return EAGAIN instead of EIO, so it's easier to
discriminate causes of failure.
Returning EAGAIN is somewhat controversial: It's technically correct
as a faster clock might become available. OTOH once all clocks are
enabled this is a permanent error. There is no ECLOCKTOOSLOW error
code.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* add spaces around binary operators in cases where it reduces readability
* align multiline statements around opening parenthesis
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
in Message-ID: <55919E72.3010807@gmx.de>
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Since only a pointer to struct i2c_client is stored in a private area
of IIO device created by the driver there's no need to allocate
sizeof(struct i2c_client) worth of storage.
Pushed to stable as this is linked to the revert patch previously.
Without this followup the original patch looks sensible.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This reverts commit e0922e5e3c.
Requested by Andrey Smirnov.
It incorrectly assumes that the level of indirection is not needed
which is not true(probably because the driver incorrectly allocates
sizeof(*client) instead of sizeof(*data) via devm_iio_device_alloc).
If you look at the code of the probe function(see below) it is easy to
see that what is being stored in the private memory of the IIO device
instance is not a copy of a 'struct i2c_client' but a pointer to an
instance passed as an argument to the probe function.
struct i2c_client **data;
int ret;
< Some code skipped >
indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*client));
if (!indio_dev)
return -ENOMEM;
data = iio_priv(indio_dev);
*data = client;
Without reverting this change any read of a raw value of this sensor
leads to a kernel oops due to a NULL pointer de-reference on my
hardware setup.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
Since setting irq-enabled GPIOs into output state is not supported
by all GPIO controllers, we need to disable the irq while requesting
sensor data. As side effect we lose a tiny bit of functionality:
Some wiring problems can't be concluded from log messages anymore.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Make sure that the read function is not interrupted...
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Harald Geyer <harald@ccbib.org>
Reviewed-by: Sanjeev Sharma <sanjeev_sharma@mentor.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
As we access i-1 we must not start with i=0.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Harald Geyer <harald@ccbib.org>
Reviewed-by: Sanjeev Sharma <sanjeev_sharma@mentor.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In si7020_read_raw() the pointer to the i2c client was obtained as second level
pointer, although a simple pointer is appropriate.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When reading temperature or humidity values, a shift of two bits to the right
needs to be applied, and only for the humidity channel a mask of the lower
12 bits needs to be applied. This reduces code repetition.
During probe, i2c_set_clientdata() was used, although its counterpart was not,
so drop it.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support to the Industrial IO subsystem
for the Silicon Labs Si7013/20/21 Relative Humidity and
Temperature Sensors.
Website: http://www.silabs.com/products/sensors/humidity-sensors/Pages/si7013-20-21.aspx
These are i2c devices which measure relative humidity
and temperature and all use the same protocol. The
Si7013 has an additional input with programmable
linearization which is not supported because that's
complicated and I didn't need it.
Signed-off-by: David Barksdale <dbarksdale@uplogix.com>
--
Changes since v1:
* Renamed to si7020 and replaced Si701x/2x with Si7013/20/21.
* Removed unneeded mutex.
* Pre-computed floating-point constant expressions.
* Removed address_list and I2C_CLASS_HWMON.
Changes since v2:
* Return correct raw sensor values.
* Rename dev variable to indio_dev.
* Issue a software reset command during probe.
* Un-broke string literal.
Changes since v3:
* enum changed to #define
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch removes the .owner field for drivers which use the
platform_driver_register api because this is overriden in
_platform_driver_register.
Signed-off-by: Sanjeev Sharma <Sanjeev_Sharma@mentor.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
sensor provides 12-bit relative humidity and 14-bit temperature
via I2C interface; temperature and linearity compensation is not
implemented (yet)
driver also supports the Si7015, but not the 2nd generation
sensors Si7013/Si7020/Si7021
datasheet is here
http://www.silabs.com/Support%20Documents/TechnicalDocs/Si7005.pdf
v2: (thanks to Lars-Peter Clausen)
* fix coding style
* use devm_iio_device_register()
* change copyright year to 2014
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
