[Why]
A "dcn20_program_front_end_for_ctx" warning is observed on Renoir.
Since the resource definition doesn't explicitly disable triplebuffer
flips like Navi10 DC actually attempts to go and setup triplebuffering
even when we pass in false to the plane state.
If we hit a full update after triplebuffering has been setup we see the
assertion since we don't expect full updates while performing
triplebuffer flips.
Normally this would get reset back to false whne we pass in the new
plane state, but since we never actually copy the flag when doing
surface updates this doesn't happen.
[How]
Copy the flag onto the plane update based on the requested surface
update state.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Right now only stream count is used to avoid split. This change updates
the W/A to check plane count instead.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When hotplug a HDMI monitor during entering S0i3 or DPMSOFF state due to
entering infinite loop when calling vbios to program pixel clocks. In
this scenario, pll is enabled but phy is not, and there is not a
programing guide for this case.
[How]
Before we having the proper programing guide, before disable pll, doing
a phy enable and disable to avoid the issue.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Due to previous code changes displays which are in active state
immediately transition to the active and added state. This makes the two
states redundant and unnecessary.
[How]
Instead of updating the device state to active and added after
successful addition, change state to inactive if addition failed. Also,
change references to active and added state to just added state.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When reprogram MSA with updated color space, the test color space shows
inconsistency. Linux has separate routine to set up test pattern color
space, but it fails to configure RGB.
[How]
Add RGB to test pattern.
Fixes: 43563bc2e6 ("drm/amd/display: update MSA and VSC SDP on video test pattern request")
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
drm_connector->display_info is not passed to amdgpu_dm right way after
read edid.
[How]
display_info is parsed from edid and saved into drm_connector by
drm_connector_update_edid_proerty which is called within
amdgpu_dm_update_connector_after_detect. call this function after read
edid to update drm_connector->display_info
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Not programming dto with same values causes test failures in DCN2 diags
DPP tests.
[HOW]
This reverts commit 1b53e73323.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes a problem found on the MacBookPro 2017 Retina panel:
The panel reports 10 bpc color depth in its EDID, and the
firmware chooses link settings at boot which support enough
bandwidth for 10 bpc (324000 kbit/sec aka LINK_RATE_RBR2
aka 0xc), but the DP_MAX_LINK_RATE dpcd register only reports
2.7 Gbps (multiplier value 0xa) as possible, in direct
contradiction of what the firmware successfully set up.
This restricts the panel to 8 bpc, not providing the full
color depth of the panel on Linux <= 5.5. Additionally, commit
'4a8ca46bae8a ("drm/amd/display: Default max bpc to 16 for eDP")'
introduced into Linux 5.6-rc1 will unclamp panel depth to
its full 10 bpc, thereby requiring a eDP bandwidth for all
modes that exceeds the bandwidth available and causes all modes
to fail validation -> No modes for the laptop panel -> failure
to set any mode -> Panel goes dark.
This patch adds a quirk specific to the MBP 2017 15" Retina
panel to override reported max link rate to the correct maximum
of 0xc = LINK_RATE_RBR2 to fix the darkness and reduced display
precision.
Please apply for Linux 5.6+ to avoid regressing Apple MBP panel
support.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These are some very loud debug statements that get printed on every
vblank when driver level debug printing is enabled in DRM, and doesn't
really tell us anything that isn't related to vblanks. So let's move
this over to the proper debug flag to be a little less spammy with our
debug output.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If "speed" is zero then we use it as a divisor to find "prescale". It's
better to move the check for zero to the very start of the function.
Fixes: 9eeec26a13 ("drm/amd/display: Refine i2c frequency calculating sequence")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These lines were accidentally indented 4 spaces more than they should
be.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We can remove the NULL check for "res_ctx" and
"res_ctx->pipe_ctx[i].stream->link". Also it's nicer to align the
conditions using spaces so I re-indented a bit.
Longer explanation: The "res_ctx" pointer points to an address in the
middle of a struct so it can't be NULL. For
"res_ctx->pipe_ctx[i].stream->link" we know that it is equal to "link"
and "link" is non-NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In dcn20_funcs and dcn21_funcs struct, the member ".dsc_pg_control = NULL"
should be removed due to .dsc_pg_control be assigned to dcn20_dsc_pg_control.
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amd-drm-next-5.7-2020-03-10:
amdgpu:
- SR-IOV fixes
- Fix up fallout from drm load/unload callback removal
- Navi, renoir power management watermark fixes
- Refactor smu parameter handling
- Display FEC fixes
- Display DCC fixes
- HDCP fixes
- Add support for USB-C PD firmware updates
- Pollock detection fix
- Rework compute ring priority handling
- RAS fixes
- Misc cleanups
amdkfd:
- Consolidate more gfx config details in amdgpu
- Consolidate bo alloc flags
- Improve code comments
- SDMA MQD fixes
- Misc cleanups
gpu scheduler:
- Add suport for modifying the sched list
uapi:
- Clarify comments about GEM_CREATE flags that are not used by userspace.
The kernel driver has always prevented userspace from using these.
They are only used internally in the kernel driver.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310212748.4519-1-alexander.deucher@amd.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl5lkYceHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGpHQH/RJrzcaZHo4lw88m
Jf7vBZ9DYUlRgqE0pxTHWmodNObKRqpwOUGflUcWbb/7GD2LQUfeqhSECVQyTID9
N9y7FcPvx321Qhc3EkZ24DBYk0+DQ0K2FVUrSa/PxO0n7czxxXWaLRDmlSULEd3R
D4pVs3zEWOBXJHUAvUQ5R+lKfkeWKNeeepeh+rezuhpdWFBRNz4Jjr5QUJ8od5xI
sIwobYmESJqTRVBHqW8g2T2/yIsFJ78GCXs8DZLe1wxh40UbxdYDTA0NDDTHKzK6
lxzBgcmKzuge+1OVmzxLouNWMnPcjFlVgXWVerpSy3/SIFFkzzUWeMbqm6hKuhOn
wAlcIgI=
=VQUc
-----END PGP SIGNATURE-----
Merge v5.6-rc5 into drm-next
Requested my mripard for some misc patches that need this as a base.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Problem Description:
Currently we are checking internal fused rev id with pci rev id. However, fused
internal rev id is the same on all raven2 parts (in which Dali and Pollock were
based on too), thus Pollock detection fails
Fix:
use the pci rev to preform the detection for bandwidth calculations.
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Aly-Tawfik <altawfik@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use the pci revision id rather than the asic silicon revision id.
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Aly-Tawfik <altawfik@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The dpp2_get_optimal_number_of_taps function is never used. Removing
just for code cleaning up.
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
FEC capability query should not be affected by debugging decision on
whether to disable FEC. We should not determine if display supports FEC
by checking debug option.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
on some displays that prefer swapped polarity we were seeing L/R images
swapped because OTG_STEREO_SYNC_OUTPUT_POLARITY would always be mapped
to 0
[how]
fix initial dal3 implementation to properly update the polarity field
according to the crtc_stereo_flags (same as
OTG_STEREO_EYE_FLAG_POLARITY)
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In HDCP Uninitialzed State, a CPIRQ event would cause log output
internal policy error because the CPIRQ event is not recognized as
unexpected event.
[how]
CPIRQ is issued in HDCP uninitialized state is unexpected. We should
set unexpected event flag in event ctx.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some RX doesn't like us to read rx id list upto max rx id list size. As
discussed, we decided to read rx id list based on device count.
[how]
According to HDCP specs the actual size of rx id list is calculated as
rx id list size = 2+3+16+5*device_count. We will read 16 bytes at a
time until it reached or exceeded rx id list size.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Link or DIG BE can't be exposed to a higher stream bandwidth than they
can handle. When DSC is required to fit the stream into the link
bandwidth, DSC has to be programmed during timing programming to ensure
this. Without it, intermittent issues such as black screen after S3 or a
hot-plug can be seen.
[how]
Move DSC programming from enabling stream on link to timing setup.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
System isn't able to enter S0i3 due to not send display count 0 to smu.
When dpms off, clk changed flag is cleared alreay, and it is checked
when doing optimized bandwidth, and update clocks is bypassed due to the
flag is unset.
[How]
Remove check flag incide the function since watermark values and clocks
values are checked during update to determine whether to perform it, no
need to check it again outside the function.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[What]
Need debug options to control lightl/deep sleep
[How]
Add registry for memory power control
Signed-off-by: Braden Bakker <Braden.Bakker@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It is possible even if sink signal is MST but driver enables SST stream.
We should not determine if we should do MST authentication based on
sink's capability.
Instead we should determine whether to do MST authentication based on
what we have enabled in stream.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
So the values of stay count and bstatus can be easily viewed during
debugging.
[How]
Add stay count and bstatus values to be outputted in HDCP log
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
nv14 previously inherited soc bb from generic dcn 2, did not match
watermark values according to memory team
[how]
add nv14 specific soc bb: copy nv2 generic that it was
using from before, but changed num channels to 8
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm_fb_helper_{add,remove}_one_connector() are dummy functions now
and serve no purpose. Hence remove their calls.
This is the preparatory step for removing the
drm_fb_helper_{add,remove}_one_connector() functions from
drm_fb_helper.h
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305120434.111091-4-pankaj.laxminarayan.bharadiya@intel.com
This interface is for dGPU Navi1x. Linux dc-pplib interface depends
on window driver dc implementation.
For Navi1x, clock settings of dcn watermarks are fixed. the settings
should be passed to smu during boot up and resume from s3.
boot up: dc calculate dcn watermark clock settings within dc_create,
dcn20_resource_construct, then call pplib functions below to pass
the settings to smu:
smu_set_watermarks_for_clock_ranges
smu_set_watermarks_table
navi10_set_watermarks_table
smu_write_watermarks_table
For Renoir, clock settings of dcn watermark are also fixed values.
dc has implemented different flow for window driver:
dc_hardware_init / dc_set_power_state
dcn10_init_hw
notify_wm_ranges
set_wm_ranges
For Linux
smu_set_watermarks_for_clock_ranges
renoir_set_watermarks_table
smu_write_watermarks_table
dc_hardware_init -> amdgpu_dm_init
dc_set_power_state --> dm_resume
therefore, linux dc-pplib interface of navi10/12/14 is different
from that of Renoir.
v2: add missing unlock in error case
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Swath sizes are being calculated incorrectly. The horizontal swath size
should be the product of block height, viewport width, and bytes per
element, but the calculation uses viewport height instead of width. The
vertical swath size is similarly incorrectly calculated. The effect of
this is that we report the wrong DCC caps.
[How]
Use viewport width in the horizontal swath size calculation and viewport
height in the vertical swath size calculation.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:147:31: warning:
address of 'pipe_ctx->plane_res' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (!pipe_ctx || !&pipe_ctx->plane_res || !&pipe_ctx->stream_res)
~ ~~~~~~~~~~^~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:147:56: warning:
address of 'pipe_ctx->stream_res' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (!pipe_ctx || !&pipe_ctx->plane_res || !&pipe_ctx->stream_res)
~ ~~~~~~~~~~^~~~~~~~~~
2 warnings generated.
As long as pipe_ctx is not NULL, the address of members in this struct
cannot be NULL, which means these checks will always evaluate to false.
Fixes: 4c1a1335df ("drm/amd/display: Driverside changes to support PSR in DMCUB")
Link: https://github.com/ClangBuiltLinux/linux/issues/915
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This interface is for dGPU Navi1x. Linux dc-pplib interface depends
on window driver dc implementation.
For Navi1x, clock settings of dcn watermarks are fixed. the settings
should be passed to smu during boot up and resume from s3.
boot up: dc calculate dcn watermark clock settings within dc_create,
dcn20_resource_construct, then call pplib functions below to pass
the settings to smu:
smu_set_watermarks_for_clock_ranges
smu_set_watermarks_table
navi10_set_watermarks_table
smu_write_watermarks_table
For Renoir, clock settings of dcn watermark are also fixed values.
dc has implemented different flow for window driver:
dc_hardware_init / dc_set_power_state
dcn10_init_hw
notify_wm_ranges
set_wm_ranges
For Linux
smu_set_watermarks_for_clock_ranges
renoir_set_watermarks_table
smu_write_watermarks_table
dc_hardware_init -> amdgpu_dm_init
dc_set_power_state --> dm_resume
therefore, linux dc-pplib interface of navi10/12/14 is different
from that of Renoir.
v2: add missing unlock in error case
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some lttpr devices do not work properly when lttpr mode is configured
after link settings.
[How]
Move lttpr configuration before lane settings.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Logger mask was updated to uint64_t, however default mask definition was
not updated for unsigned long long
[How]
Update DC_DEFAULT_LOG_MASK to support uint64_t type
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Disabling FEC for specific monitors is sometimes required for debugging
while in the monitor bringup phase
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We see an issue that caused clk_optimized_required to be set true in
certain cases, causing passive flips to fail. This is because of a typo
where wm_optimized_required was set twice.
[HOW]
Set clk_optimized_required to false after updating clocks.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
vstartup calculation is incorrect due to use 2 number of cursors and
result in an underflow when playing video in full screen mode and
combines graphic plane and video plane.
[How]
Apply new policy for dml calculation.
1 cursor for graphic plane, 0 cursor for video plane.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Swath sizes are being calculated incorrectly. The horizontal swath size
should be the product of block height, viewport width, and bytes per
element, but the calculation uses viewport height instead of width. The
vertical swath size is similarly incorrectly calculated. The effect of
this is that we report the wrong DCC caps.
[How]
Use viewport width in the horizontal swath size calculation and viewport
height in the vertical swath size calculation.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Freesync borderless is not meant to be enabled on any APUs
[HOW]
Add is_apu cap to dcn21_resource_construct for correct recognition
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
SMU FW previously had an issue with lowering display clock to below 100
MHz, and a workaround was put in to limit it. Newest SMU FW does not
have this issue, and no longer needs the 100MHz cap.
[HOW]
Remove the 100MHz cap based on the SMU FW version.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When transitioning from SST to MST, the HDCP repeater in some MST
displays will enter a bad state. The HDCP repeater is recovered after
failing and performing authentication again.
[How]
Add monitor patch to trigger HDCP authentication failure after
encryption is enabled and re-authenticate.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
