Previous code made an assumption that the power on value of global
control MSR has enabled all fixed and general purpose counters properly.
However, this is not the case for certain Intel processors, such as
Atom - and it might also be firmware dependent.
Each enable bit in IA32_PERF_GLOBAL_CTRL is AND'ed with the
enable bits for all privilege levels in the respective IA32_PERFEVTSELx
or IA32_PERF_FIXED_CTR_CTRL MSRs to start/stop the counting of
respective counters. Counting is enabled if the AND'ed results is true;
counting is disabled when the result is false.
The end result is that all fixed counters are always disabled on Atom
processors because the assumption is just invalid.
Fix this by not initializing the ctrl-mask out of the global MSR,
but setting it to perf_counter_mask.
Reported-by: Stephane Eranian <eranian@googlemail.com>
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20090624021324.GA2788@ywang-moblin2.bj.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To support domain-isolation usages, the platform hardware must be
capable of uniquely identifying the requestor (source-id) for each
interrupt message. Without source-id checking for interrupt remapping
, a rouge guest/VM with assigned devices can launch interrupt attacks
to bring down anothe guest/VM or the VMM itself.
This patch adds source-id checking for interrupt remapping, and then
really isolates interrupts for guests/VMs with assigned devices.
Because PCI subsystem is not initialized yet when set up IOAPIC
entries, use read_pci_config_byte to access PCI config space directly.
Signed-off-by: Weidong Han <weidong.han@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Calling mcheck_init() on resume is required only with
CONFIG_X86_OLD_MCE=y.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The init_gbpages() function is conditionally called from
init_memory_mapping() function. There are two call-sites where
this 'after_bootmem' condition can be true: setup_arch() and
mem_init() via pci_iommu_alloc().
Therefore, it's safe to move the call to init_gbpages() to
setup_arch() as it's always called before mem_init().
This removes an after_bootmem use - paving the way to remove
all uses of that state variable.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <Pine.LNX.4.64.0906221731210.19474@melkki.cs.Helsinki.FI>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.infradead.org/~dwmw2/iommu-2.6.31:
intel-iommu: Fix one last ia64 build problem in Pass Through Support
VT-d: support the device IOTLB
VT-d: cleanup iommu_flush_iotlb_psi and flush_unmaps
VT-d: add device IOTLB invalidation support
VT-d: parse ATSR in DMA Remapping Reporting Structure
PCI: handle Virtual Function ATS enabling
PCI: support the ATS capability
intel-iommu: dmar_set_interrupt return error value
intel-iommu: Tidy up iommu->gcmd handling
intel-iommu: Fix tiny theoretical race in write-buffer flush.
intel-iommu: Clean up handling of "caching mode" vs. IOTLB flushing.
intel-iommu: Clean up handling of "caching mode" vs. context flushing.
VT-d: fix invalid domain id for KVM context flush
Fix !CONFIG_DMAR build failure introduced by Intel IOMMU Pass Through Support
Intel IOMMU Pass Through Support
Fix up trivial conflicts in drivers/pci/{intel-iommu.c,intr_remapping.c}
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (74 commits)
PCI: make msi_free_irqs() to use msix_mask_irq() instead of open coded write
PCI: Fix the NIU MSI-X problem in a better way
PCI ASPM: remove get_root_port_link
PCI ASPM: cleanup pcie_aspm_sanity_check
PCI ASPM: remove has_switch field
PCI ASPM: cleanup calc_Lx_latency
PCI ASPM: cleanup pcie_aspm_get_cap_device
PCI ASPM: cleanup clkpm checks
PCI ASPM: cleanup __pcie_aspm_check_state_one
PCI ASPM: cleanup initialization
PCI ASPM: cleanup change input argument of aspm functions
PCI ASPM: cleanup misc in struct pcie_link_state
PCI ASPM: cleanup clkpm state in struct pcie_link_state
PCI ASPM: cleanup latency field in struct pcie_link_state
PCI ASPM: cleanup aspm state field in struct pcie_link_state
PCI ASPM: fix typo in struct pcie_link_state
PCI: drivers/pci/slot.c should depend on CONFIG_SYSFS
PCI: remove redundant __msi_set_enable()
PCI PM: consistently use type bool for wake enable variable
x86/ACPI: Correct maximum allowed _CRS returned resources and warn if exceeded
...
On extreme configuration (e.g. 32bit 32-way NUMA machine), lpage
percpu first chunk allocator can consume too much of vmalloc space.
Make it fall back to 4k allocator if the consumption goes over 20%.
[ Impact: add sanity check for lpage percpu first chunk allocator ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jan Beulich <JBeulich@novell.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>
According to Andi, it isn't clear whether lpage allocator is worth the
trouble as there are many processors where PMD TLB is far scarcer than
PTE TLB. The advantage or disadvantage probably depends on the actual
size of percpu area and specific processor. As performance
degradation due to TLB pressure tends to be highly workload specific
and subtle, it is difficult to decide which way to go without more
data.
This patch implements percpu_alloc kernel parameter to allow selecting
which first chunk allocator to use to ease debugging and testing.
While at it, make sure all the failure paths report why something
failed to help determining why certain allocator isn't working. Also,
kill the "Great future plan" comment which had already been realized
quite some time ago.
[ Impact: allow explicit percpu first chunk allocator selection ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jan Beulich <JBeulich@novell.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>
lpage allocator aliases a PMD page for each cpu and returns whatever
is unused to the page allocator. When the pageattr of the recycled
pages are changed, this makes the two aliases point to the overlapping
regions with different attributes which isn't allowed and known to
cause subtle data corruption in certain cases.
This can be handled in simliar manner to the x86_64 highmap alias.
pageattr code should detect if the target pages have PMD alias and
split the PMD alias and synchronize the attributes.
pcpur allocator is updated to keep the allocated PMD pages map sorted
in ascending address order and provide pcpu_lpage_remapped() function
which binary searches the array to determine whether the given address
is aliased and if so to which address. pageattr is updated to use
pcpu_lpage_remapped() to detect the PMD alias and split it up as
necessary from cpa_process_alias().
Jan Beulich spotted the original problem and incorrect usage of vaddr
instead of laddr for lookup.
With this, lpage percpu allocator should work correctly. Re-enable
it.
[ Impact: fix subtle lpage pageattr bug and re-enable lpage ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jan Beulich <JBeulich@novell.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>
Reorganize cpa_process_alias() so that new alias condition can be
added easily.
Jan Beulich spotted problem in the original cleanup thread which
incorrectly assumed the two existing conditions were mutially
exclusive.
[ Impact: code reorganization ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>
Make the following changes in preparation of coming pageattr updates.
* Define and use array of struct pcpul_ent instead of array of
pointers. The only difference is ->cpu field which is set but
unused yet.
* Rename variables according to the above change.
* Rename local variable vm to pcpul_vm and move it out of the
function.
[ Impact: no functional difference ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>
The "remap" allocator remaps large pages to build the first chunk;
however, the name isn't very good because 4k allocator remaps too and
the whole point of the remap allocator is using large page mapping.
The allocator will be generalized and exported outside of x86, rename
it to lpage before that happens.
percpu_alloc kernel parameter is updated to accept both "remap" and
"lpage" for lpage allocator.
[ Impact: code cleanup, kernel parameter argument updated ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
In the failure path, setup_pcpu_remap() tries to free the area which
has already been freed to make holes in the large page. Fix it.
[ Impact: fix duplicate free in failure path ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: aes-ni - Remove CRYPTO_TFM_REQ_MAY_SLEEP from fpu template
crypto: aes-ni - Do not sleep when using the FPU
crypto: aes-ni - Fix cbc mode IV saving
crypto: padlock-aes - work around Nano CPU errata in CBC mode
crypto: padlock-aes - work around Nano CPU errata in ECB mode
This allows the callers to now pass down the full set of FAULT_FLAG_xyz
flags to handle_mm_fault(). All callers have been (mechanically)
converted to the new calling convention, there's almost certainly room
for architectures to clean up their code and then add FAULT_FLAG_RETRY
when that support is added.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This counts when building sched domains in case NUMA information
is not available.
( See cpu_coregroup_mask() which uses llc_shared_map which in turn is
created based on cpu_llc_id. )
Currently Linux builds domains as follows:
(example from a dual socket quad-core system)
CPU0 attaching sched-domain:
domain 0: span 0-7 level CPU
groups: 0 1 2 3 4 5 6 7
...
CPU7 attaching sched-domain:
domain 0: span 0-7 level CPU
groups: 7 0 1 2 3 4 5 6
Ever since that is borked for multi-core AMD CPU systems.
This patch fixes that and now we get a proper:
CPU0 attaching sched-domain:
domain 0: span 0-3 level MC
groups: 0 1 2 3
domain 1: span 0-7 level CPU
groups: 0-3 4-7
...
CPU7 attaching sched-domain:
domain 0: span 4-7 level MC
groups: 7 4 5 6
domain 1: span 0-7 level CPU
groups: 4-7 0-3
This allows scheduler to assign tasks to cores on different sockets
(i.e. that don't share last level cache) for performance reasons.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20090619085909.GJ5218@alberich.amd.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The discussion about using "access_ok()" in get_user_pages_fast() (see
commit 7f81890687: "x86: don't use
'access_ok()' as a range check in get_user_pages_fast()" for details and
end result), made us notice that x86-64 was really being very sloppy
about virtual address checking.
So be way more careful and straightforward about masking x86-64 virtual
addresses:
- All the VIRTUAL_MASK* variants now cover half of the address
space, it's not like we can use the full mask on a signed
integer, and the larger mask just invites mistakes when
applying it to either half of the 48-bit address space.
- /proc/kcore's kc_offset_to_vaddr() becomes a lot more
obvious when it transforms a file offset into a
(kernel-half) virtual address.
- Unify/simplify the 32-bit and 64-bit USER_DS definition to
be based on TASK_SIZE_MAX.
This cleanup and more careful/obvious user virtual address checking also
uncovered a buglet in the x86-64 implementation of strnlen_user(): it
would do an "access_ok()" check on the whole potential area, even if the
string itself was much shorter, and thus return an error even for valid
strings. Our sloppy checking had hidden this.
So this fixes 'strnlen_user()' to do this properly, the same way we
already handled user strings in 'strncpy_from_user()'. Namely by just
checking the first byte, and then relying on fault handling for the
rest. That always works, since we impose a guard page that cannot be
mapped at the end of the user space address space (and even if we
didn't, we'd have the address space hole).
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (49 commits)
perfcounter: Handle some IO return values
perf_counter: Push perf_sample_data through the swcounter code
perf_counter tools: Define and use our own u64, s64 etc. definitions
perf_counter: Close race in perf_lock_task_context()
perf_counter, x86: Improve interactions with fast-gup
perf_counter: Simplify and fix task migration counting
perf_counter tools: Add a data file header
perf_counter: Update userspace callchain sampling uses
perf_counter: Make callchain samples extensible
perf report: Filter to parent set by default
perf_counter tools: Handle lost events
perf_counter: Add event overlow handling
fs: Provide empty .set_page_dirty() aop for anon inodes
perf_counter: tools: Makefile tweaks for 64-bit powerpc
perf_counter: powerpc: Add processor back-end for MPC7450 family
perf_counter: powerpc: Make powerpc perf_counter code safe for 32-bit kernels
perf_counter: powerpc: Change how processor-specific back-ends get selected
perf_counter: powerpc: Use unsigned long for register and constraint values
perf_counter: powerpc: Enable use of software counters on 32-bit powerpc
perf_counter tools: Add and use isprint()
...
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix out of scope variable access in sched_slice()
sched: Hide runqueues from direct refer at source code level
sched: Remove unneeded __ref tag
sched, x86: Fix cpufreq + sched_clock() TSC scaling
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (24 commits)
tracing/urgent: warn in case of ftrace_start_up inbalance
tracing/urgent: fix unbalanced ftrace_start_up
function-graph: add stack frame test
function-graph: disable when both x86_32 and optimize for size are configured
ring-buffer: have benchmark test print to trace buffer
ring-buffer: do not grab locks in nmi
ring-buffer: add locks around rb_per_cpu_empty
ring-buffer: check for less than two in size allocation
ring-buffer: remove useless compile check for buffer_page size
ring-buffer: remove useless warn on check
ring-buffer: use BUF_PAGE_HDR_SIZE in calculating index
tracing: update sample event documentation
tracing/filters: fix race between filter setting and module unload
tracing/filters: free filter_string in destroy_preds()
ring-buffer: use commit counters for commit pointer accounting
ring-buffer: remove unused variable
ring-buffer: have benchmark test handle discarded events
ring-buffer: prevent adding write in discarded area
tracing/filters: strloc should be unsigned short
tracing/filters: operand can be negative
...
Fix up kmemcheck-induced conflict in kernel/trace/ring_buffer.c manually
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (45 commits)
x86, mce: fix error path in mce_create_device()
x86: use zalloc_cpumask_var for mce_dev_initialized
x86: fix duplicated sysfs attribute
x86: de-assembler-ize asm/desc.h
i386: fix/simplify espfix stack switching, move it into assembly
i386: fix return to 16-bit stack from NMI handler
x86, ioapic: Don't call disconnect_bsp_APIC if no APIC present
x86: Remove duplicated #include's
x86: msr.h linux/types.h is only required for __KERNEL__
x86: nmi: Add Intel processor 0x6f4 to NMI perfctr1 workaround
x86, mce: mce_intel.c needs <asm/apic.h>
x86: apic/io_apic.c: dmar_msi_type should be static
x86, io_apic.c: Work around compiler warning
x86: mce: Don't touch THERMAL_APIC_VECTOR if no active APIC present
x86: mce: Handle banks == 0 case in K7 quirk
x86, boot: use .code16gcc instead of .code16
x86: correct the conversion of EFI memory types
x86: cap iomem_resource to addressable physical memory
x86, mce: rename _64.c files which are no longer 64-bit-specific
x86, mce: mce.h cleanup
...
Manually fix up trivial conflict in arch/x86/mm/fault.c
It's really not right to use 'access_ok()', since that is meant for the
normal "get_user()" and "copy_from/to_user()" accesses, which are done
through the TLB, rather than through the page tables.
Why? access_ok() does both too few, and too many checks. Too many,
because it is meant for regular kernel accesses that will not honor the
'user' bit in the page tables, and because it honors the USER_DS vs
KERNEL_DS distinction that we shouldn't care about in GUP. And too few,
because it doesn't do the 'canonical' check on the address on x86-64,
since the TLB will do that for us.
So instead of using a function that isn't meant for this, and does
something else and much more complicated, just do the real rules: we
don't want the range to overflow, and on x86-64, we want it to be a
canonical low address (on 32-bit, all addresses are canonical).
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arch_acpi_processor_cleanup_pdc() in x86 and ia64 results in memory allocated
for _PDC objects that is never freed and will cause memory leak in case of
physical CPU remove and add. Patch fixes the memory leak by freeing the
objects soon after _PDC is evaluated.
Reported-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Improve a few details in perfcounter call-chain recording that
makes use of fast-GUP:
- Use ACCESS_ONCE() to observe the pte value. ptes are fundamentally
racy and can be changed on another CPU, so we have to be careful
about how we access them. The PAE branch is already careful with
read-barriers - but the non-PAE and 64-bit side needs an
ACCESS_ONCE() to make sure the pte value is observed only once.
- make the checks a bit stricter so that we can feed it any kind of
cra^H^H^H user-space input ;-)
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Before exposing upstream tools to a callchain-samples ABI, tidy it
up to make it more extensible in the future:
Use markers in the IP chain to denote context, use (u64)-1..-4095 range
for these context markers because we use them for ERR_PTR(), so these
addresses are unlikely to be mapped.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In case gcc does something funny with the stack frames, or the return
from function code, we would like to detect that.
An arch may implement passing of a variable that is unique to the
function and can be saved on entering a function and can be tested
when exiting the function. Usually the frame pointer can be used for
this purpose.
This patch also implements this for x86. Where it passes in the stack
frame of the parent function, and will test that frame on exit.
There was a case in x86_32 with optimize for size (-Os) where, for a
few functions, gcc would align the stack frame and place a copy of the
return address into it. The function graph tracer modified the copy and
not the actual return address. On return from the funtion, it did not go
to the tracer hook, but returned to the parent. This broke the function
graph tracer, because the return of the parent (where gcc did not do
this funky manipulation) returned to the location that the child function
was suppose to. This caused strange kernel crashes.
This test detected the problem and pointed out where the issue was.
This modifies the parameters of one of the functions that the arch
specific code calls, so it includes changes to arch code to accommodate
the new prototype.
Note, I notice that the parsic arch implements its own push_return_trace.
This is now a generic function and the ftrace_push_return_trace should be
used instead. This patch does not touch that code.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Enable gcov profiling of the entire kernel on x86_64. Required changes
include disabling profiling for:
* arch/kernel/acpi/realmode and arch/kernel/boot/compressed:
not linked to main kernel
* arch/vdso, arch/kernel/vsyscall_64 and arch/kernel/hpet:
profiling causes segfaults during boot (incompatible context)
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Li Wei <W.Li@Sun.COM>
Cc: Michael Ellerman <michaele@au1.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Heiko Carstens <heicars2@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <mschwid2@linux.vnet.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kernel_fpu_begin/end used preempt_disable/enable, so sleep should be
prevented between kernel_fpu_begin/end.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Because AES-NI instructions will touch XMM state, corresponding code
must be enclosed within kernel_fpu_begin/end, which used
preempt_disable/enable. So sleep should be prevented between
kernel_fpu_begin/end.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Original implementation of aesni_cbc_dec do not save IV if input
length % 4 == 0. This will make decryption of next block failed.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We need a cleared cpu_mask to record if mce is initialized, especially
when MAXSMP is used.
used zalloc_... instead
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: stable@kernel.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The sysfs attribute cmci_disabled was accidentall turned into a
duplicate of ignore_ce, breaking all other attributes.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
asm/desc.h is included in three assembly files, but the only macro
it defines, GET_DESC_BASE, is never used. This patch removes the
includes, removes the macro GET_DESC_BASE and the ASSEMBLY guard
from asm/desc.h.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The espfix code triggers if we have a protected mode userspace
application with a 16-bit stack. On returning to userspace, with iret,
the CPU doesn't restore the high word of the stack pointer. This is an
"official" bug, and the work-around used in the kernel is to temporarily
switch to a 32-bit stack segment/pointer pair where the high word of the
pointer is equal to the high word of the userspace stackpointer.
The current implementation uses THREAD_SIZE to determine the cut-off,
but there is no good reason not to use the more natural 64kb... However,
implementing this by simply substituting THREAD_SIZE with 65536 in
patch_espfix_desc crashed the test application. patch_espfix_desc tries
to do what is described above, but gets it subtly wrong if the userspace
stack pointer is just below a multiple of THREAD_SIZE: an overflow
occurs to bit 13... With a bit of luck, when the kernelspace
stackpointer is just below a 64kb-boundary, the overflow then ripples
trough to bit 16 and userspace will see its stack pointer changed by
65536.
This patch moves all espfix code into entry_32.S. Selecting a 16-bit
cut-off simplifies the code. The game with changing the limit dynamically
is removed too. It complicates matters and I see no value in it. Changing
only the top 16-bit word of ESP is one instruction and it also implies
that only two bytes of the ESPFIX GDT entry need to be changed and this
can be implemented in just a handful simple to understand instructions.
As a side effect, the operation to compute the original ESP from the
ESPFIX ESP and the GDT entry simplifies a bit too, and the remaining
three instructions have been expanded inline in entry_32.S.
impact: can now reliably run userspace with ESP=xxxxfffc on 16-bit
stack segment
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Acked-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Returning to a task with a 16-bit stack requires special care: the iret
instruction does not restore the high word of esp in that case. The
espfix code fixes this, but currently is not invoked on NMIs. This means
that a running task gets the upper word of esp clobbered due intervening
NMIs. To reproduce, compile and run the following program with the nmi
watchdog enabled (nmi_watchdog=2 on the command line). Using gdb you can
see that the high bits of esp contain garbage, while the low bits are
still correct.
This patch puts the espfix code back into the NMI code path.
The patch is slightly complicated due to the irqtrace infrastructure not
being NMI-safe. The NMI return path cannot call TRACE_IRQS_IRET.
Otherwise, the tail of the normal iret-code is correct for the nmi code
path too. To be able to share this code-path, the TRACE_IRQS_IRET was
move up a bit. The espfix code exists after the TRACE_IRQS_IRET, but
this code explicitly disables interrupts. This short interrupts-off
section is now not traced anymore. The return-to-kernel path now always
includes the preliminary test to decide if the espfix code should be
called. This is never the case, but doing it this way keeps the patch as
simple as possible and the few extra instructions should not affect
timing in any significant way.
#define _GNU_SOURCE
#include <stdio.h>
#include <sys/types.h>
#include <sys/mman.h>
#include <unistd.h>
#include <sys/syscall.h>
#include <asm/ldt.h>
int modify_ldt(int func, void *ptr, unsigned long bytecount)
{
return syscall(SYS_modify_ldt, func, ptr, bytecount);
}
/* this is assumed to be usable */
#define SEGBASEADDR 0x10000
#define SEGLIMIT 0x20000
/* 16-bit segment */
struct user_desc desc = {
.entry_number = 0,
.base_addr = SEGBASEADDR,
.limit = SEGLIMIT,
.seg_32bit = 0,
.contents = 0, /* ??? */
.read_exec_only = 0,
.limit_in_pages = 0,
.seg_not_present = 0,
.useable = 1
};
int main(void)
{
setvbuf(stdout, NULL, _IONBF, 0);
/* map a 64 kb segment */
char *pointer = mmap((void *)SEGBASEADDR, SEGLIMIT+1,
PROT_EXEC|PROT_READ|PROT_WRITE,
MAP_SHARED|MAP_ANONYMOUS, -1, 0);
if (pointer == NULL) {
printf("could not map space\n");
return 0;
}
/* write ldt, new mode */
int err = modify_ldt(0x11, &desc, sizeof(desc));
if (err) {
printf("error modifying ldt: %i\n", err);
return 0;
}
for (int i=0; i<1000; i++) {
asm volatile (
"pusha\n\t"
"mov %ss, %eax\n\t" /* preserve ss:esp */
"mov %esp, %ebp\n\t"
"push $7\n\t" /* index 0, ldt, user mode */
"push $65536-4096\n\t" /* esp */
"lss (%esp), %esp\n\t" /* switch to new stack */
"push %eax\n\t" /* save old ss:esp on new stack */
"push %ebp\n\t"
"add $17*65536, %esp\n\t" /* set high bits */
"mov %esp, %edx\n\t"
"mov $10000000, %ecx\n\t" /* wait... */
"1: loop 1b\n\t" /* ... a bit */
"cmp %esp, %edx\n\t"
"je 1f\n\t"
"ud2\n\t" /* esp changed inexplicably! */
"1:\n\t"
"sub $17*65536, %esp\n\t" /* restore high bits */
"lss (%esp), %esp\n\t" /* restore old ss:esp */
"popa\n\t");
printf("\rx%ix", i);
}
return 0;
}
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Acked-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Instead of open-coding pci_find_parent_resource and request_resource,
just call pci_claim_resource.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 9e350de37a ("perf_counter: Accurate period data")
missed a spot, which caused all Intel-PMU samples to have a
period of 0.
This broke auto-freq sampling.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
<linux/types.h> is only required for __KERNEL__ as whole file is covered with it
Also fixed some spacing issues for usr/include/asm-x86/msr.h
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: "H. Peter Anvin" <hpa@kernel.org>
LKML-Reference: <1245228070.2662.1.camel@ht.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] cpumask: new cpumask operators for arch/x86/kernel/cpu/cpufreq/powernow-k8.c
[CPUFREQ] cpumask: avoid playing with cpus_allowed in powernow-k8.c
[CPUFREQ] cpumask: avoid cpumask games in arch/x86/kernel/cpu/cpufreq/speedstep-centrino.c
[CPUFREQ] cpumask: avoid playing with cpus_allowed in speedstep-ich.c
[CPUFREQ] powernow-k8: get drv data for correct CPU
[CPUFREQ] powernow-k8: read P-state from HW
[CPUFREQ] reduce scope of ACPI_PSS_BIOS_BUG_MSG[]
[CPUFREQ] Clean up convoluted code in arch/x86/kernel/tsc.c:time_cpufreq_notifier()
[CPUFREQ] minor correction to cpu-freq documentation
[CPUFREQ] powernow-k8.c: mess cleanup
[CPUFREQ] Only set sampling_rate_max deprecated, sampling_rate_min is useful
[CPUFREQ] powernow-k8: Set transition latency to 1 if ACPI tables export 0
[CPUFREQ] ondemand: Uncouple minimal sampling rate from HZ in NO_HZ case
Expand Intel NMI perfctr1 workaround to include a Core2 processor stepping
(cpuid family-6, model-f, stepping-4). Resolves a situation where the NMI
would not enable on these processors.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: prarit@redhat.com
Cc: suresh.b.siddha@intel.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
mce_intel.c uses apic_write() and lapic_get_maxlvt(), and so it needs
<asm/apic.h>.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
This compiler warning:
arch/x86/kernel/apic/io_apic.c: In function ‘ioapic_write_entry’:
arch/x86/kernel/apic/io_apic.c:466: warning: ‘eu’ is used uninitialized in this function
arch/x86/kernel/apic/io_apic.c:465: note: ‘eu’ was declared here
Is bogus as 'eu' is always initialized. But annotate it away by
initializing the variable, to make it easier for people to notice
real warnings. A compiler that sees through this logic will
optimize away the initialization.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
LKML-Reference: <1245248720.3312.27.camel@myhost>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If APIC was disabled (for some reason) and as result
it's not even mapped we should not try to enable thermal
interrupts at all.
Reported-by: Simon Holm Thøgersen <odie@cs.aau.dk>
Tested-by: Simon Holm Thøgersen <odie@cs.aau.dk>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
LKML-Reference: <20090615182633.GA7606@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For freqency dependent TSCs we only scale the cycles, we do not account
for the discrepancy in absolute value.
Our current formula is: time = cycles * mult
(where mult is a function of the cpu-speed on variable tsc machines)
Suppose our current cycle count is 10, and we have a multiplier of 5,
then our time value would end up being 50.
Now cpufreq comes along and changes the multiplier to say 3 or 7,
which would result in our time being resp. 30 or 70.
That means that we can observe random jumps in the time value due to
frequency changes in both fwd and bwd direction.
So what this patch does is change the formula to:
time = cycles * frequency + offset
And we calculate offset so that time_before == time_after, thereby
ridding us of these jumps in time.
[ Impact: fix/reduce sched_clock() jumps across frequency changing events ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Chucked-on-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
* akpm: (182 commits)
fbdev: bf54x-lq043fb: use kzalloc over kmalloc/memset
fbdev: *bfin*: fix __dev{init,exit} markings
fbdev: *bfin*: drop unnecessary calls to memset
fbdev: bfin-t350mcqb-fb: drop unused local variables
fbdev: blackfin has __raw I/O accessors, so use them in fb.h
fbdev: s1d13xxxfb: add accelerated bitblt functions
tcx: use standard fields for framebuffer physical address and length
fbdev: add support for handoff from firmware to hw framebuffers
intelfb: fix a bug when changing video timing
fbdev: use framebuffer_release() for freeing fb_info structures
radeon: P2G2CLK_ALWAYS_ONb tested twice, should 2nd be P2G2CLK_DAC_ALWAYS_ONb?
s3c-fb: CPUFREQ frequency scaling support
s3c-fb: fix resource releasing on error during probing
carminefb: fix possible access beyond end of carmine_modedb[]
acornfb: remove fb_mmap function
mb862xxfb: use CONFIG_OF instead of CONFIG_PPC_OF
mb862xxfb: restrict compliation of platform driver to PPC
Samsung SoC Framebuffer driver: add Alpha Channel support
atmel-lcdc: fix pixclock upper bound detection
offb: use framebuffer_alloc() to allocate fb_info struct
...
Manually fix up conflicts due to kmemcheck in mm/slab.c
Convert most arches to use asm-generic/kmap_types.h.
Move the KM_FENCE_ macro additions into asm-generic/kmap_types.h,
controlled by __WITH_KM_FENCE from each arch's kmap_types.h file.
Would be nice to be able to add custom KM_types per arch, but I don't yet
see a nice, clean way to do that.
Built on x86_64, i386, mips, sparc, alpha(tonyb), powerpc(tonyb), and
68k(tonyb).
Note: avr32 should be able to remove KM_PTE2 (since it's not used) and
then just use the generic kmap_types.h file. Get avr32 maintainer
approval.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "Luck Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are some places to be able to use printk_once instead of hard coding.
Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Callers of alloc_pages_node() can optionally specify -1 as a node to mean
"allocate from the current node". However, a number of the callers in
fast paths know for a fact their node is valid. To avoid a comparison and
branch, this patch adds alloc_pages_exact_node() that only checks the nid
with VM_BUG_ON(). Callers that know their node is valid are then
converted.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Paul Mundt <lethal@linux-sh.org> [for the SLOB NUMA bits]
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* create mm/init-mm.c, move init_mm there
* remove INIT_MM, initialize init_mm with C99 initializer
* unexport init_mm on all arches:
init_mm is already unexported on x86.
One strange place is some OMAP driver (drivers/video/omap/) which
won't build modular, but it's already wants get_vm_area() export.
Somebody should look there.
[akpm@linux-foundation.org: add missing #includes]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Americo Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PIT_TICK_RATE is currently defined in four architectures, but in three
different places. While linux/timex.h is not the perfect place for it, it
is still a reasonable replacement for those drivers that traditionally use
asm/timex.h to get CLOCK_TICK_RATE and expect it to be the PIT frequency.
Note that for Alpha, the actual value changed from 1193182UL to 1193180UL.
This is unlikely to make a difference, and probably can only improve
accuracy. There was a discussion on the correct value of CLOCK_TICK_RATE
a few years ago, after which every existing instance was getting changed
to 1193182. According to the specification, it should be
1193181.818181...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Len Brown <lenb@kernel.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use .code16gcc to compile arch/x86/boot/bioscall.S rather than
.code16, since some older versions of binutils can't generate 32-bit
addressing expressions (67 prefixes) in .code16 mode, only in
.code16gcc mode.
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This patch causes all the EFI_RESERVED_TYPE memory reservations to be recorded
in the e820 table as type E820_RESERVED.
(This patch replaces one called 'x86: vendor reserved memory type'.
This version has been discussed a bit with Peter and Yinghai but not given
a final opinion.)
Without this patch EFI_RESERVED_TYPE memory reservations may be
marked usable in the e820 table. There may be a collision between
kernel use and some reserver's use of this memory.
(An example use of this functionality is the UV system, which
will access extremely large areas of memory with a memory engine
that allows a user to address beyond the processor's range. Such
areas are reserved in the EFI table by the BIOS.
Some loaders have a restricted number of entries possible in the e820 table,
hence the need to record the reservations in the unrestricted EFI table.)
The call to do_add_efi_memmap() is only made if "add_efi_memmap" is specified
on the kernel command line.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
iomem_resource is by default initialized to -1, which means 64 bits of
physical address space if 64-bit resources are enabled. However, x86
CPUs cannot address 64 bits of physical address space. Thus, we want
to cap the physical address space to what the union of all CPU can
actually address.
Without this patch, we may end up assigning inaccessible values to
uninitialized 64-bit PCI memory resources.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Martin Mares <mj@ucw.cz>
Cc: stable@kernel.org
Rename files that are no longer 64bit specific:
mce_amd_64.c => mce_amd.c
mce_intel_64.c => mce_intel.c
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Now all symbols in the header are static. Remove the header.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
move intel_init_thermal() into therm_throt.c
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Put common functions into therm_throt.c, modify Makefile.
unexpected_thermal_interrupt
intel_thermal_interrupt
smp_thermal_interrupt
intel_set_thermal_handler
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Break smp_thermal_interrupt() into two functions.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Remove unused argument regs from handlers, and use inc_irq_stat.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The mce_disabled on 32bit is a tristate variable [1,0,-1],
while 64bit version is boolean [0,1].
This patch makes mce_disabled always boolean, and use mce_p5_enabled
to indicate the third state instead.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
There are 2 headers:
arch/x86/include/asm/mce.h
arch/x86/kernel/cpu/mcheck/mce.h
and in the latter small header:
#include <asm/mce.h>
This patch move all contents in the latter header into the former,
and fix all files using the latter to include the former instead.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add sysfs interface for admins who want to tweak these options without
rebooting the system.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
"trigger" is not straight forward name for valiable that holds name
of user mode helper program which triggered by machine check events.
This patch renames this valiable and kins to more recognizable names.
trigger => mce_helper
trigger_argv => mce_helper_argv
notify_user => mce_need_notify
No functional changes.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add __read_mostly to data written during setup.
Suggested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Simplify interface of mce_start():
- no_way_out = mce_start(no_way_out, &order);
+ order = mce_start(&no_way_out);
Now Monarch and Subjects share same exit(return) in usual path.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
In mce_cpu_restart, mce_init_timer is called unconditionally.
If !mce_available (e.g. mce is disabled), there are no useful work
for timer. Stop running it.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
If one CPU has no_way_out == 1, all other CPUs should have no_way_out
== 1. But despite global_nwo is read after mce_callin, global_nwo is
updated after mce_callin too. So it is possible that some CPU read
global_nwo before some other CPU update global_nwo, so that no_way_out
== 1 for some CPU, while no_way_out == 0 for some other CPU.
This patch fixes this race condition via moving mce_callin updating
after global_nwo updating, with a smp_wmb in between. A smp_rmb is
added between their reading too.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Issue a warning if _CRS returns too many resource descriptors to be
accommodated by the fixed size resource array instances. If there is no
transparent bridge on the root bus "too many" is the
PCI_BUS_NUM_RESOURCES size of the resource array. Otherwise, the last 3
slots of the resource array must be excluded making the maximum
(PCI_BUS_NUM_RESOURCES - 3).
The current code:
- is silent when _CRS returns too many resource descriptors and
- incorrectly allows use of the last 3 slots of the resource array
for a root bus with a transparent bridge
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Prefetch instructions can generate spurious faults on certain
models of older CPUs. The faults themselves cannot be stopped
and they can occur pretty much anywhere - so the way we solve
them is that we detect certain patterns and ignore the fault.
There is one small path of code where we must not take faults
though: the #PF handler execution leading up to the reading
of the CR2 (the faulting address). If we take a fault there
then we destroy the CR2 value (with that of the prefetching
instruction's) and possibly mishandle user-space or
kernel-space pagefaults.
It turns out that in current upstream we do exactly that:
prefetchw(&mm->mmap_sem);
/* Get the faulting address: */
address = read_cr2();
This is not good.
So turn around the order: first read the cr2 then prefetch
the lock address. Reading cr2 is plenty fast (2 cycles) so
delaying the prefetch by this amount shouldnt be a big issue
performance-wise.
[ And this might explain a mystery fault.c warning that sometimes
occurs on one an old AMD/Semptron based test-system i have -
which does have such prefetch problems. ]
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
LKML-Reference: <20090616030522.GA22162@Krystal>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that enable_iommus() will call iommu_disable() for each iommu,
the call to disable_iommus() during resume is redundant. Also, the order
for an invalidation is to invalidate device table entries first, then
domain translations.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This adds support to the x86 cpuid and msr drivers to report the proper
device name to userspace for their devices.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for misc devices to report their requested nodename to
userspace. It also updates a number of misc drivers to provide the
needed subdirectory and device name to be used for them.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'timers-for-linus-migration' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers: Logic to move non pinned timers
timers: /proc/sys sysctl hook to enable timer migration
timers: Identifying the existing pinned timers
timers: Framework for identifying pinned timers
timers: allow deferrable timers for intervals tv2-tv5 to be deferred
Fix up conflicts in kernel/sched.c and kernel/timer.c manually
Remove all old-style cpumask operators, and cpumask_t.
Also: get rid of the unused define_siblings function.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Mark Langsdorf <mark.langsdorf@amd.com>
Tested-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
cpumask: avoid playing with cpus_allowed in powernow-k8.c
It's generally a very bad idea to mug some process's cpumask: it could
legitimately and reasonably be changed by root, which could break us
(if done before our code) or them (if we restore the wrong value).
I did not replace powernowk8_target; it needs fixing, but it grabs a
mutex (so no smp_call_function_single here) but Mark points out it can
be called multiple times per second, so work_on_cpu is too heavy.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
To: cpufreq@vger.kernel.org
Acked-by: Mark Langsdorf <mark.langsdorf@amd.com>
Tested-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Impact: don't play with current's cpumask
It's generally a very bad idea to mug some process's cpumask: it could
legitimately and reasonably be changed by root, which could break us
(if done before our code) or them (if we restore the wrong value).
Use rdmsr_on_cpu and wrmsr_on_cpu instead.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
To: cpufreq@vger.kernel.org
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Impact: don't play with current's cpumask
It's generally a very bad idea to mug some process's cpumask: it could
legitimately and reasonably be changed by root, which could break us
(if done before our code) or them (if we restore the wrong value).
We use smp_call_function_single: this had the advantage of being more
efficient, too.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
To: cpufreq@vger.kernel.org
Cc: Dominik Brodowski <linux@brodo.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Make powernowk8_get() similar to powernowk8_target() and powernowk8_verify()
in the way it obtains "powernow_data" for a given CPU.
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Langsdorf, Mark <mark.langsdorf@amd.com>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Reviewed-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Tested-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Acked-by: Langsdorf, Mark <mark.langsdorf@amd.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
By definition, "cpuinfo_cur_freq" should report the value from HW. So, don't
depend on the cached value. Instead read P-state directly from HW, while
taking into account the erratum 311 workaround for Fam 11h processors.
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Langsdorf, Mark <mark.langsdorf@amd.com>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Reviewed-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Tested-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Acked-by: Langsdorf, Mark <mark.langsdorf@amd.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
This symbol doesn't need file-global scope.
Cc: "Zhang, Rui" <rui.zhang@intel.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Langsdorf, Mark <mark.langsdorf@amd.com>
Cc: Leo Milano <lmilano@gmx.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Christoph Hellwig noticed the following potential uninitialised use:
> arch/x86/kernel/tsc.c: In function 'time_cpufreq_notifier':
> arch/x86/kernel/tsc.c:634: warning: 'dummy' may be used uninitialized in this function
>
> where we do have CONFIG_SMP set, freq->flags & CPUFREQ_CONST_LOOPS is
> true and ref_freq is false.
It seems plausable, though the circumstances for hitting it are really low.
Nearly all SMP capable cpufreq drivers set CPUFREQ_CONST_LOOPS.
powernow-k8 is really the only exception. The older CPUs were typically
only ever UP. (powernow-k7 never supported SMP for eg)
It's worth fixing regardless, as it cleans up the code.
Fix possible uninitialized use of dummy, by just removing it,
and making the setting of lpj more obvious.
Signed-off-by: Dave Jones <davej@redhat.com>
This doesn't fix anything, but it's expected that a transition latency of 0
could cause trouble in the future.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Cc: Langsdorf, Mark <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
I just realized this has a kmap_atomic bug in...
The below would fix it - but it's complicating this code
some more.
Alternatively I would have to introduce something like
pte_offset_map_irq() which would make the irq/nmi detection and leave
the regular code paths alone, however that would mean either duplicating
the gup_fast() pagewalk or passing down a pte function pointer, which
would only duplicate the gup_pte_range() bit, neither is really
attractive ...
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
CC: Nick Piggin <npiggin@suse.de>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
At present, every architecture that supports perf_counters has to
declare set_perf_counter_pending() in its arch-specific headers.
This consolidates the declarations into a single declaration in one
common place, include/linux/perf_counter.h. On powerpc, we continue
to provide a static inline definition of set_perf_counter_pending()
in the powerpc hw_irq.h.
Also, this removes from the x86 perf_counter.h the unused null
definitions of {test,clear}_perf_counter_pending.
Reported-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: benh@kernel.crashing.org
LKML-Reference: <18998.13388.920691.523227@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
These registers may contain values from previous kernels. So reset them
to known values before enable the event buffer again.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
__copy_from_user_inatomic() isn't NMI safe in that it can trigger
the page fault handler which is another trap and its return path
invokes IRET which will also close the NMI context.
Therefore use a GUP based approach to copy the stack frames over.
We tried an alternative solution as well: we used a forward ported
version of Mathieu Desnoyers's "NMI safe INT3 and Page Fault" patch
that modifies the exception return path to use an open-coded IRET with
explicit stack unrolling and TF checking.
This didnt work as it interacted with faulting user-space instructions,
causing them not to restart properly, which corrupts user-space
registers.
Solving that would probably involve disassembling those instructions
and backtracing the RIP. But even without that, the code was deemed
rather complex to the already non-trivial x86 entry assembly code,
so instead we went for this GUP based method that does a
software-walk of the pagetables.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Two new kmap_atomic slots for NMI context. And teach pte_offset_map()
about NMI context.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
CC: Nick Piggin <npiggin@suse.de>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce a gup_fast() variant which is usable from IRQ/NMI context.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
CC: Nick Piggin <npiggin@suse.de>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The IOMMU spec states that IOMMU behavior may be undefined when the
IOMMU registers are rewritten while command or event buffer is enabled.
Disable them in IOMMU disable path.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
We've had some troubles in the past with weird instructions. This
patch adds a self-test framework which can be used to verify that
a certain set of opcodes are decoded correctly. Of course, the
opcodes which are not tested can still give the wrong results.
In short, this is just a safeguard to catch unintentional changes
in the opcode decoder. It does not mean that errors can't still
occur!
[rebased for mainline inclusion]
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Only _PAGE_HIDDEN when CONFIG_KMEMCHECK is defined, otherwise set it
to 0. Allows later cleanups.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
[rebased for mainline inclusion]
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
The Kconfig options of kmemcheck are hidden under arch/x86 which makes porting
to other architectures harder. To fix that, move the Kconfig bits to
lib/Kconfig.kmemcheck and introduce a CONFIG_HAVE_ARCH_KMEMCHECK config option
that architectures can define.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
[rebased for mainline inclusion]
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
let it rip!
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[rebased for mainline inclusion]
Signed-off-by: Vegard Nossum <vegardno@ifi.uio.no>
This adds support for tracking the initializedness of memory that
was allocated with the page allocator. Highmem requests are not
tracked.
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
[build fix for !CONFIG_KMEMCHECK]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[rebased for mainline inclusion]
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
When kexec'ing to a new kernel (for example, when crashing and launching
a kdump session), the AMD IOMMU may have cached translations. The kexec'd
kernel, during initialization, will invalidate the IOMMU device table
entries, but not the domain translations. These stale entries can cause
a device's DMA to fail, makes it rough to write a dump to disk when the
disk controller can't DMA ;-)
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
If the IOMMUs are still enabled when the kexec kernel boots access to
the disk is not possible. This is bad for tools like kdump or anything
else which wants to use PCI devices.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
When the IOMMU stays enabled the BIOS may not be able to finish the
machine shutdown properly. So disable the hardware on shutdown.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This is needed for page allocator support to prevent false positives
when accessing pages which are dma-mapped.
[rebased for mainline inclusion]
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
As these are allocated using the page allocator, we need to pass
__GFP_NOTRACK before we add page allocator support to kmemcheck.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
This patch hooks into the DMA API to prevent the reporting of the
false positives that would otherwise be reported when memory is
accessed that is also used directly by devices.
[rebased for mainline inclusion]
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
With kmemcheck enabled, the slab allocator needs to do this:
1. Tell kmemcheck to allocate the shadow memory which stores the status of
each byte in the allocation proper, e.g. whether it is initialized or
uninitialized.
2. Tell kmemcheck which parts of memory that should be marked uninitialized.
There are actually a few more states, such as "not yet allocated" and
"recently freed".
If a slab cache is set up using the SLAB_NOTRACK flag, it will never return
memory that can take page faults because of kmemcheck.
If a slab cache is NOT set up using the SLAB_NOTRACK flag, callers can still
request memory with the __GFP_NOTRACK flag. This does not prevent the page
faults from occuring, however, but marks the object in question as being
initialized so that no warnings will ever be produced for this object.
In addition to (and in contrast to) __GFP_NOTRACK, the
__GFP_NOTRACK_FALSE_POSITIVE flag indicates that the allocation should
not be tracked _because_ it would produce a false positive. Their values
are identical, but need not be so in the future (for example, we could now
enable/disable false positives with a config option).
Parts of this patch were contributed by Pekka Enberg but merged for
atomicity.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[rebased for mainline inclusion]
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
The hooks that we modify are:
- Page fault handler (to handle kmemcheck faults)
- Debug exception handler (to hide pages after single-stepping
the instruction that caused the page fault)
Also redefine memset() to use the optimized version if kmemcheck is
enabled.
(Thanks to Pekka Enberg for minimizing the impact on the page fault
handler.)
As kmemcheck doesn't handle MMX/SSE instructions (yet), we also disable
the optimized xor code, and rely instead on the generic C implementation
in order to avoid false-positive warnings.
Signed-off-by: Vegard Nossum <vegardno@ifi.uio.no>
[whitespace fixlet]
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[rebased for mainline inclusion]
Signed-off-by: Vegard Nossum <vegardno@ifi.uio.no>
Lets use kmemcheck_pte_lookup() in kmemcheck_fault() instead of
open-coding it there.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
This patch moves the CONFIG_X86_64 ifdef out of kmemcheck_opcode_decode() by
introducing a version of the function that always returns false for
CONFIG_X86_32.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Multiple ifdef'd definitions of the same global variable is ugly and
error-prone. Fix that up.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
The "Bugs, beware!" printout during is cute but confuses users that something
bad happened so change the text to the more boring "Initialized" message.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
This patch reorders code in error.c so that we can get rid of the forward
declarations.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Kernel-space call-chains were trimmed at the first entry because
we never processed anything beyond the first stack context.
Allow the backtrace to jump from NMI to IRQ stack then to task stack
and finally user-space stack.
Also calculate the stack and bp variables correctly so that the
stack walker does not exit early.
We can get deep traces as a result, visible in perf report -D output:
0x32af0 [0xe0]: PERF_EVENT (IP, 5): 15134: 0xffffffff815225fd period: 1
... chain: u:2, k:22, nr:24
..... 0: 0xffffffff815225fd
..... 1: 0xffffffff810ac51c
..... 2: 0xffffffff81018e29
..... 3: 0xffffffff81523939
..... 4: 0xffffffff81524b8f
..... 5: 0xffffffff81524bd9
..... 6: 0xffffffff8105e498
..... 7: 0xffffffff8152315a
..... 8: 0xffffffff81522c3a
..... 9: 0xffffffff810d9b74
..... 10: 0xffffffff810dbeec
..... 11: 0xffffffff810dc3fb
This is a 22-entries kernel-space chain.
(We still only record reliable stack entries.)
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix the ptregs variant when we hit user-mode tasks.
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
timer interrupts are excluded from being disabled during suspend. The
clock events code manages the disabling of clock events on its own
because the timer interrupt needs to be functional before the resume
code reenables the device interrupts.
The hpet per cpu timers request their interrupt without setting the
IRQF_TIMER flag so suspend_device_irqs() disables them as well which
results in a fatal resume failure on the boot CPU.
Adding IRQF_TIMER to the interupt flags when requesting the hpet per
cpu timer interrupts solves the problem.
Reported-by: Benjamin S. <sbenni@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Benjamin S. <sbenni@gmx.de>
Cc: stable@kernel.org
Fix kernel-doc warnings in atomic_32.h:
Warning(arch/x86/include/asm/atomic_32.h:265): No description found for parameter 'ptr'
Warning(arch/x86/include/asm/atomic_32.h:265): Excess function parameter 'v' description in '__atomic64_read'
Warning(arch/x86/include/asm/atomic_32.h:305): Excess function parameter 'old_val' description in 'atomic64_xchg'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
LKML-Reference: <4A3467E6.6010907@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (35 commits)
hwrng: timeriomem - Fix potential oops (request_mem_region/__devinit)
crypto: api - Use formatting of module name
crypto: testmgr - Allow hash test vectors longer than a page
crypto: testmgr - Check all test vector lengths
crypto: hifn_795x - fix __dev{init,exit} markings
crypto: tcrypt - Do not exit on success in fips mode
crypto: compress - Return produced bytes in crypto_{,de}compress_{update,final}
hwrng: via_rng - Support VIA Nano hardware RNG on X86_64 builds
hwrng: via_rng - Support VIA Nano hardware RNG
hwrng: via_rng - The VIA Hardware RNG driver is for the CPU, not Chipset
crypto: testmgr - Skip algs not flagged fips_allowed in fips mode
crypto: testmgr - Mark algs allowed in fips mode
crypto: testmgr - Add ctr(aes) test vectors
crypto: testmgr - Dynamically allocate xbuf and axbuf
crypto: testmgr - Print self-test pass notices in fips mode
crypto: testmgr - Catch base cipher self-test failures in fips mode
crypto: testmgr - Add ansi_cprng test vectors
crypto: testmgr - Add infrastructure for ansi_cprng self-tests
crypto: testmgr - Add self-tests for rfc4309(ccm(aes))
crypto: testmgr - Handle AEAD test vectors expected to fail verification
...
kmemcheck/shadow.c needs to include <linux/module.h> to prevent
the following warnings:
linux-next-20080724/arch/x86/mm/kmemcheck/shadow.c:64: warning : data definition has no type or storage class
linux-next-20080724/arch/x86/mm/kmemcheck/shadow.c:64: warning : type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
linux-next-20080724/arch/x86/mm/kmemcheck/shadow.c:64: warning : parameter names (without types) in function declaration
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: vegardno@ifi.uio.no
Cc: penberg@cs.helsinki.fi
Cc: akpm <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
General description: kmemcheck is a patch to the linux kernel that
detects use of uninitialized memory. It does this by trapping every
read and write to memory that was allocated dynamically (e.g. using
kmalloc()). If a memory address is read that has not previously been
written to, a message is printed to the kernel log.
Thanks to Andi Kleen for the set_memory_4k() solution.
Andrew Morton suggested documenting the shadow member of struct page.
Signed-off-by: Vegard Nossum <vegardno@ifi.uio.no>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
[export kmemcheck_mark_initialized]
[build fix for setup_max_cpus]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[rebased for mainline inclusion]
Signed-off-by: Vegard Nossum <vegardno@ifi.uio.no>
All AMD models share the same hw caching related event table.
Also complete the table with more events.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <1244835381.2802.2.camel@ht.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
AMD supports performance monitoring start from K7 (i.e. family 6),
so disable it for earlier AMD CPUs.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <1244714289.6923.0.camel@ht.satnam>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move
arch/x86/kernel/acpi/boot.c: acpi_parse_mcfg()
to
arch/x86/pci/mmconfig-shared.c: pci_parse_mcfg()
where it is used, and make it static.
Move associated globals and helper routine with it.
No functional change.
This code move is in preparation for SFI support,
which will allow the PCI code to find the MCFG table
on systems which do not support ACPI.
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This will help kmemcheck (and possibly other debugging tools) since we
can now simply pass regs->bp to the stack tracer instead of specifying
the number of stack frames to skip, which is unreliable if gcc decides
to inline functions, etc.
Note that this makes the API incomplete for other architectures, but I
expect that those can be updated lazily, e.g. when they need it.
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_counter: Start documenting HAVE_PERF_COUNTERS requirements
perf_counter: Add forward/backward attribute ABI compatibility
perf record: Explicity program a default counter
perf_counter: Remove PERF_TYPE_RAW special casing
perf_counter: PERF_TYPE_HW_CACHE is a hardware counter too
powerpc, perf_counter: Fix performance counter event types
perf_counter/x86: Add a quirk for Atom processors
perf_counter tools: Remove one L1-data alias
This patch (as1241) renames a bunch of functions in the PM core.
Rather than go through a boring list of name changes, suffice it to
say that in the end we have a bunch of pairs of functions:
device_resume_noirq dpm_resume_noirq
device_resume dpm_resume
device_complete dpm_complete
device_suspend_noirq dpm_suspend_noirq
device_suspend dpm_suspend
device_prepare dpm_prepare
in which device_X does the X operation on a single device and dpm_X
invokes device_X for all devices in the dpm_list.
In addition, the old dpm_power_up and device_resume_noirq have been
combined into a single function (dpm_resume_noirq).
Lastly, dpm_suspend_start and dpm_resume_end are the renamed versions
of the former top-level device_suspend and device_resume routines.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Rename the functions performing "_noirq" dev_pm_ops
operations from device_power_down() and device_power_up()
to device_suspend_noirq() and device_resume_noirq().
The new function names are chosen to show that the functions
are responsible for calling the _noirq() versions to finalize
the suspend/resume operation. The current function names do
not perform power down/up anymore so the names may be misleading.
Global function renames:
- device_power_down() -> device_suspend_noirq()
- device_power_up() -> device_resume_noirq()
Static function renames:
- suspend_device_noirq() -> __device_suspend_noirq()
- resume_device_noirq() -> __device_resume_noirq()
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Len Brown <lenb@kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This is the last unification step. Here we do remove one of the files
and rename the left one as cpu.c, as both are now the same.
Also update power/Makefile, telling it to build cpu.o, instead of
cpu_(32|64).o
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: Lauro Salmito <laurosalmito@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
In this step, we do unify the copyright notes for both files
cpu_32.c and cpu_64.c, making such files exactly the same.
It's the last step before the actual unification, that will
rename one of them to cpu.c and remove the other one.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: Lauro Salmito <laurosalmito@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
In this step we do unify cpu_32.c and cpu_64.c functions that
work on restoring the saved processor state. Also, we do
eliminate the forward declaration of fix_processor_context()
for X86_64, as it's not needed anymore.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: Lauro Salmito <laurosalmito@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
In this step we do unify cpu_32.c and cpu_64.c functions that
work on saving the processor state.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: Lauro Salmito <laurosalmito@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Aiming total unification of cpu_32.c and cpu_64.c, in this step
we do unify the global variables and existing forward declarations
for such files.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: Lauro Salmito <laurosalmito@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
First step towards the unification of cpu_32.c and cpu_64.c.
This commit unifies the headers of such files, making both
of them use the same header files. It also remove the uneeded
<module.h>.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: Lauro Salmito <laurosalmito@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
One of the numbers in arch/x86/kernel/acpi/sleep.c is long, but it is
not annotated appropriately, so sparese warns about it. Fix that.
[rjw: added the changelog.]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* 'topic/slab/earlyboot-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
slab: setup cpu caches later on when interrupts are enabled
slab,slub: don't enable interrupts during early boot
slab: fix gfp flag in setup_cpu_cache()
x86: make zap_low_mapping could be used early
irq: slab alloc for default irq_affinity
memcg: fix page_cgroup fatal error in FLATMEM
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-lguest: (31 commits)
lguest: add support for indirect ring entries
lguest: suppress notifications in example Launcher
lguest: try to batch interrupts on network receive
lguest: avoid sending interrupts to Guest when no activity occurs.
lguest: implement deferred interrupts in example Launcher
lguest: remove obsolete LHREQ_BREAK call
lguest: have example Launcher service all devices in separate threads
lguest: use eventfds for device notification
eventfd: export eventfd_signal and eventfd_fget for lguest
lguest: allow any process to send interrupts
lguest: PAE fixes
lguest: PAE support
lguest: Add support for kvm_hypercall4()
lguest: replace hypercall name LHCALL_SET_PMD with LHCALL_SET_PGD
lguest: use native_set_* macros, which properly handle 64-bit entries when PAE is activated
lguest: map switcher with executable page table entries
lguest: fix writev returning short on console output
lguest: clean up length-used value in example launcher
lguest: Segment selectors are 16-bit long. Fix lg_cpu.ss1 definition.
lguest: beyond ARRAY_SIZE of cpu->arch.gdt
...
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-module-and-param:
module: cleanup FIXME comments about trimming exception table entries.
module: trim exception table on init free.
module: merge module_alloc() finally
uml module: fix uml build process due to this merge
x86 module: merge the rest functions with macros
x86 module: merge the same functions in module_32.c and module_64.c
uvesafb: improve parameter handling.
module_param: allow 'bool' module_params to be bool, not just int.
module_param: add __same_type convenience wrapper for __builtin_types_compatible_p
module_param: split perm field into flags and perm
module_param: invbool should take a 'bool', not an 'int'
cyber2000fb.c: use proper method for stopping unload if CONFIG_ARCH_SHARK
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Provide _sdata in the vmlinux.lds.S file
x86: handle initrd that extends into unusable memory
This version requires that host and guest have the same PAE status.
NX cap is not offered to the guest, yet.
Signed-off-by: Matias Zabaljauregui <zabaljauregui@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Add support for kvm_hypercall4(); PAE wants it.
Signed-off-by: Matias Zabaljauregui <zabaljauregui at gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
replace LHCALL_SET_PMD with LHCALL_SET_PGD hypercall name
(That's really what it is, and the confusion gets worse with PAE support)
Signed-off-by: Matias Zabaljauregui <zabaljauregui@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reported-by: Jeremy Fitzhardinge <jeremy@goop.org>
Some cleanups and replace direct assignment with native_set_* macros which properly handle 64-bit entries when PAE is activated
Signed-off-by: Matias Zabaljauregui <zabaljauregui@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The downside of the last patch which made restore_flags and irq_enable
check interrupts is that they are now too big to be patched directly
into the callsites, so the C versions are always used.
But the C versions go via PV_CALLEE_SAVE_REGS_THUNK which saves all
the registers. In fact, we don't need any registers in the fast path,
so we can do better than this if we actually code them in assembler.
The results are in the noise, but since it's about the same amount of
code, it's worth applying.
1GB Guest->Host: input(suppressed),output(suppressed)
Before:
Seconds: 0:16.53
Packets: 377268,753673
Interrupts: 22461,24297
Notifications: 1(5245),21303(732370)
Net IRQs triggered: 377023(245),42578(711095)
After:
Seconds: 0:16.48
Packets: 377289,753673
Interrupts: 22281,24465
Notifications: 1(5245),21296(732377)
Net IRQs triggered: 377060(229),42564(711109)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
lguest never checked for pending interrupts when enabling interrupts, and
things still worked. However, it makes a significant difference to TCP
performance, so it's time we fixed it by introducing a pending_irq flag
and checking it on irq_restore and irq_enable.
These two routines are now too big to patch into the 8/10 bytes
patch space, so we drop that code.
Note: The high latency on interrupt delivery had a very curious
effect: once everything else was optimized, networking without GSO was
faster than networking with GSO, since more interrupts were sent and
hence a greater chance of one getting through to the Guest!
Note2: (Almost) Closing the same loophole for iret doesn't have any
measurable effect, so I'm leaving that patch for the moment.
Before:
1GB tcpblast Guest->Host: 30.7 seconds
1GB tcpblast Guest->Host (no GSO): 76.0 seconds
After:
1GB tcpblast Guest->Host: 6.8 seconds
1GB tcpblast Guest->Host (no GSO): 27.8 seconds
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Copy from arch/x86/kernel/irqinit_32.c: we don't use the vectors beyond
LGUEST_IRQS (if any), but we might as well set them all.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
kernel_physical_mapping_init() could be called in memory hotplug path.
[ Impact: fix potential crash with memory hotplug ]
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
LKML-Reference: <20090612045752.GA827@sli10-desk.sh.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Everyone cut and paste this comment from my original one. We now do
it generically, so cut the comments.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Amerigo Wang <amwang@redhat.com>
As Christoph Hellwig suggested, module_alloc() actually can be
unified for i386 and x86_64 (of course, also UML).
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: 'Ingo Molnar' <mingo@elte.hu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Merge the same functions both in module_32.c and module_64.c into
module.c.
This is the first step to merge both of them finally.
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The fixed-function performance counters do not work on current Atom
processors. Use the general-purpose ones instead.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <20090612080855.GA2286@ywang-moblin2.bj.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
_sdata is a common symbol defined by many architectures and made
available to the kernel via asm-generic/sections.h. Kmemleak uses this
symbol when scanning the data sections.
[ Impact: add new global symbol ]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
LKML-Reference: <20090511122105.26556.96593.stgit@pc1117.cambridge.arm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
So we make sure MAXSMP gets a cleared cpumask
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On a system where system memory (according e820) is not covered by
mtrr, mtrr_trim_memory converts a portion of memory to reserved, but
bootloader has already put the initrd in that range.
Thus, we need to have 64bit to use relocate_initrd too.
[ Impact: fix using initrd when mtrr_trim_memory happen ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: stable@kernel.org
* 'perfcounters-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (574 commits)
perf_counter: Turn off by default
perf_counter: Add counter->id to the throttle event
perf_counter: Better align code
perf_counter: Rename L2 to LL cache
perf_counter: Standardize event names
perf_counter: Rename enums
perf_counter tools: Clean up u64 usage
perf_counter: Rename perf_counter_limit sysctl
perf_counter: More paranoia settings
perf_counter: powerpc: Implement generalized cache events for POWER processors
perf_counters: powerpc: Add support for POWER7 processors
perf_counter: Accurate period data
perf_counter: Introduce struct for sample data
perf_counter tools: Normalize data using per sample period data
perf_counter: Annotate exit ctx recursion
perf_counter tools: Propagate signals properly
perf_counter tools: Small frequency related fixes
perf_counter: More aggressive frequency adjustment
perf_counter/x86: Fix the model number of Intel Core2 processors
perf_counter, x86: Correct some event and umask values for Intel processors
...
* 'topic/slab/earlyboot' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
vgacon: use slab allocator instead of the bootmem allocator
irq: use kcalloc() instead of the bootmem allocator
sched: use slab in cpupri_init()
sched: use alloc_cpumask_var() instead of alloc_bootmem_cpumask_var()
memcg: don't use bootmem allocator in setup code
irq/cpumask: make memoryless node zero happy
x86: remove some alloc_bootmem_cpumask_var calling
vt: use kzalloc() instead of the bootmem allocator
sched: use kzalloc() instead of the bootmem allocator
init: introduce mm_init()
vmalloc: use kzalloc() instead of alloc_bootmem()
slab: setup allocators earlier in the boot sequence
bootmem: fix slab fallback on numa
bootmem: use slab if bootmem is no longer available
At this point, it seems to solve more problems than it causes, so let's try using it by default. It's an easy revert if it ends up causing trouble.
Reviewed-by: Yinghai Lu <yhlu.kernel@gmail.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We should not assign 64bit ranges to PCI devices that only take 32bit
prefetchable addresses.
Try to set IORESOURCE_MEM_64 in 64bit resource of pci_device/pci_bridge
and make the bus resource only have that bit set when all devices under
it support 64bit prefetchable memory. Use that flag to allocate
resources from that range.
Reported-by: Yannick <yannick.roehlly@free.fr>
Reviewed-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The current asm-generic/page.h only contains the get_order
function, and asm-generic/uaccess.h only implements
unaligned accesses. This renames the file to getorder.h
and uaccess-unaligned.h to make room for new page.h
and uaccess.h file that will be usable by all simple
(e.g. nommu) architectures.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The existing asm-generic/atomic.h only defines the
atomic_long type. This renames it to atomic-long.h
so we have a place to add a truly generic atomic.h
that can be used on all non-SMP systems.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
This provides a reliable way for asm-generic/types.h and other
files to find out if it is running on a 32 or 64 bit platform.
We cannot use CONFIG_64BIT for this in headers that are included
from user space because CONFIG symbols are not available there.
We also cannot do it inside of asm/types.h because some headers
need the word size but cannot include types.h.
The solution is to introduce a new header <asm/bitsperlong.h>
that defines both __BITS_PER_LONG for user space and
BITS_PER_LONG for usage in the kernel. The asm-generic
version falls back to 32 bit unless the architecture overrides
it, which I did for all 64 bit platforms.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The existing asm-generic versions are incomplete and included
by some architectures. New architectures should be able
to use a generic version, so rename the existing files and
change all users, which lets us add the new files.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'kvm-updates/2.6.31' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (138 commits)
KVM: Prevent overflow in largepages calculation
KVM: Disable large pages on misaligned memory slots
KVM: Add VT-x machine check support
KVM: VMX: Rename rmode.active to rmode.vm86_active
KVM: Move "exit due to NMI" handling into vmx_complete_interrupts()
KVM: Disable CR8 intercept if tpr patching is active
KVM: Do not migrate pending software interrupts.
KVM: inject NMI after IRET from a previous NMI, not before.
KVM: Always request IRQ/NMI window if an interrupt is pending
KVM: Do not re-execute INTn instruction.
KVM: skip_emulated_instruction() decode instruction if size is not known
KVM: Remove irq_pending bitmap
KVM: Do not allow interrupt injection from userspace if there is a pending event.
KVM: Unprotect a page if #PF happens during NMI injection.
KVM: s390: Verify memory in kvm run
KVM: s390: Sanity check on validity intercept
KVM: s390: Unlink vcpu on destroy - v2
KVM: s390: optimize float int lock: spin_lock_bh --> spin_lock
KVM: s390: use hrtimer for clock wakeup from idle - v2
KVM: s390: Fix memory slot versus run - v3
...
Don't hardcode to node zero for early boot IRQ setup memory allocations.
[ penberg@cs.helsinki.fi: minor cleanups ]
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Now that we set up the slab allocator earlier, we can get rid of some
alloc_bootmem_cpumask_var() calls in boot code.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
* serial-from-alan: (79 commits)
moxa: prevent opening unavailable ports
imx: serial: use tty_encode_baud_rate to set true rate
imx: serial: add IrDA support to serial driver
imx: serial: use rational library function
lib: isolate rational fractions helper function
imx: serial: handle initialisation failure correctly
imx: serial: be sure to stop xmit upon shutdown
imx: serial: notify higher layers in case xmit IRQ was not called
imx: serial: fix one bit field type
imx: serial: fix whitespaces (no changes in functionality)
tty: use prepare/finish_wait
tty: remove sleep_on
sierra: driver interface blacklisting
sierra: driver urb handling improvements
tty: resolve some sierra breakage
timbuart: Fix the termios logic
serial: Added Timberdale UART driver
tty: Add URL for ttydev queue
devpts: unregister the file system on error
tty: Untangle termios and mm mutex dependencies
...
The top (fastest) and last level (biggest) caches are the most
interesting ones, performance wise.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
[ Fixed the Nehalem LL table to LLC Reference/Miss events ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Pure renames only, to PERF_COUNT_HW_* and PERF_COUNT_SW_*.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The legacy TCSETA{,W,F} ioctls failed to set the termio->c_line field
on x86. This adds a missing get_user.
The same ioctls also fail to report faulting user pointers, which
we keep ignoring.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit c9690998ef (x86: memtest: remove
64-bit division) introduced following compile warning:
arch/x86/mm/memtest.c: In function 'memtest':
arch/x86/mm/memtest.c:56: warning: comparison of distinct pointer types lacks a cast
arch/x86/mm/memtest.c:58: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch introduces three boot options (no_cmci, dont_log_ce
and ignore_ce) to control handling for corrected errors.
The "mce=no_cmci" boot option disables the CMCI feature.
Since CMCI is a new feature so having boot controls to disable
it will be a help if the hardware is misbehaving.
The "mce=dont_log_ce" boot option disables logging for corrected
errors. All reported corrected errors will be cleared silently.
This option will be useful if you never care about corrected
errors.
The "mce=ignore_ce" boot option disables features for corrected
errors, i.e. polling timer and cmci. All corrected events are
not cleared and kept in bank MSRs.
Usually this disablement is not recommended, however it will be
a help if there are some conflict with the BIOS or hardware
monitoring applications etc., that clears corrected events in
banks instead of OS.
[ And trivial cleanup (space -> tab) for doc is included. ]
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
LKML-Reference: <4A30ACDF.5030408@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch:
- Adds print_mce_head() instead of first flag
- Makes the header to be printed always
- Stops double printing of corrected errors
[ This portion originates from Huang Ying's patch ]
Originally-From: Huang Ying <ying.huang@intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
LKML-Reference: <4A30AC83.5010708@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (244 commits)
Revert "x86, bts: reenable ptrace branch trace support"
tracing: do not translate event helper macros in print format
ftrace/documentation: fix typo in function grapher name
tracing/events: convert block trace points to TRACE_EVENT(), fix !CONFIG_BLOCK
tracing: add protection around module events unload
tracing: add trace_seq_vprint interface
tracing: fix the block trace points print size
tracing/events: convert block trace points to TRACE_EVENT()
ring-buffer: fix ret in rb_add_time_stamp
ring-buffer: pass in lockdep class key for reader_lock
tracing: add annotation to what type of stack trace is recorded
tracing: fix multiple use of __print_flags and __print_symbolic
tracing/events: fix output format of user stack
tracing/events: fix output format of kernel stack
tracing/trace_stack: fix the number of entries in the header
ring-buffer: discard timestamps that are at the start of the buffer
ring-buffer: try to discard unneeded timestamps
ring-buffer: fix bug in ring_buffer_discard_commit
ftrace: do not profile functions when disabled
tracing: make trace pipe recognize latency format flag
...
