The Enhanced Connection Complete event is use in conjunction with LL
Privacy and not Extended Advertising.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In case LL Privacy is supported by the controller, it is also a good
idea to use the LE Enhanced Connection Complete event for getting all
information about the new connection and its addresses.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When starting active scanning for discovery the whitelist is not needed
to be used. So the filter_policy is 0x00. To make the core more readable
use a variable name instead of just setting 0 as paramter.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The error could indicate a problem with the Bluetooth device. It
is easier to investigate if the packet's actual length gets logged,
not just the fact that a discrepancy occurred.
Signed-off-by: Daniels Umanovskis <du@axentia.se>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To improve security, always give the user-space daemon a chance to
accept or reject a Just Works pairing (LE). The daemon may decide to
auto-accept based on the user's intent.
This patch is similar to the previous patch but applies for LE Secure
Connections (SC).
Signed-off-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some static checker run by 0day reports a variableScope warning.
net/bluetooth/smp.c:870:6: warning:
The scope of the variable 'err' can be reduced. [variableScope]
There is no need for two separate variables holding return values.
Stick with the existing variable. While at it, don't pre-initialize
'ret' because it is set in each code path.
tk_request() is supposed to return a negative error code on errors,
not a bluetooth return code. The calling code converts the return
value to SMP_UNSPECIFIED if needed.
Fixes: 92516cd97f ("Bluetooth: Always request for user confirmation for Just Works")
Cc: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BT qualification test SM/MAS/PKE/BV-01-C needs us to turn off
the MITM flag when pairing, and at the same time also set the io
capability to something other than no input no output.
Currently the MITM flag is only unset when the io capability is set
to no input no output, therefore the test cannot be executed.
This patch introduces a debugfs option to force MITM flag to be
turned off.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Increment the mgmt revision due to the recently added new commands.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To allow userspace to make correcty security policy decision, the kernel
needs to export a few details of the supported security features and
encryption key size information. This command exports this information
and also allows future extensions if needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the Read Local Simple Pairing Options command it is possible to
retrieve the support for max encryption key size supported by the
controller and also if the controller correctly verifies the ECDH public
key during pairing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Micrsoft defined a set for HCI vendor extensions. Check the following
link for details:
https://docs.microsoft.com/en-us/windows-hardware/drivers/bluetooth/microsoft-defined-bluetooth-hci-commands-and-events
This provides the basic framework to enable the extension and read its
supported features. Drivers still have to declare support for this
extension before it can be utilized by the host stack.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is just a cosmetic clean to move the selftests configuration option
to the bottom of the list of options.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
notifying using HCI_NOTIFY_CONN_ADD for SCO connection is generic in
case of mSBC audio. To differntiate SCO air mode introducing
HCI_NOTIFY_ENABLE_SCO_CVSD and HCI_NOTIFY_ENABLE_SCO_TRANSP.
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When scheduling TX packets, send all SCO/eSCO packets first, check for
pending SCO/eSCO packets after every ACL/LE packet and send them if any
are pending. This is done to make sure that we can meet SCO deadlines
on slow interfaces like UART.
If we were to queue up multiple ACL packets without checking for a SCO
packet, we might miss the SCO timing. For example:
The time it takes to send a maximum size ACL packet (1024 bytes):
t = 10/8 * 1024 bytes * 8 bits/byte * 1 packet / baudrate
where 10/8 is uart overhead due to start/stop bits per byte
Replace t = 3.75ms (SCO deadline), which gives us a baudrate of 2730666.
At a baudrate of 3000000, if we didn't check for SCO packets within 1024
bytes, we would miss the 3.75ms timing window.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To improve security, always give the user-space daemon a chance to
accept or reject a Just Works pairing (LE). The daemon may decide to
auto-accept based on the user's intent.
Signed-off-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds BT_MODE socket option which can be used to set L2CAP modes,
including modes only supported over LE which were not supported using
the L2CAP_OPTIONS.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
L2CAP_OPTIONS shall only be used with BR/EDR modes.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses the DEFER_SETUP flag to group channels with
L2CAP_CREDIT_BASED_CONNECTION_REQ.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With this change, the encryption key size is not assumed to be 16 if the
read_encryption_key_size command fails for any reason. This ensures
that if the controller fails the command for any reason that the
encryption key size isn't implicitely set to 16 and instead take a more
concervative posture to assume it is 0.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds a callback to read the socket pid.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When handling auto-connected devices, we should execute the rest of the
connection complete when it was previously discovered and it is an ACL
connection.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If Bluetooth fails to enter the suspended state correctly, restore the
state to running (re-enabling scans). PM_POST_SUSPEND is only sent to
notifiers that successfully return from PM_PREPARE_SUSPEND notification
so we should recover gracefully if it fails.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
BlueZ cancels adv when starting a scan, but does not cancel a scan when
starting to adv. Neither is required, so this brings both to a
consistent state (of not affecting each other). Some very rare (I've
never seen one) BT 4.0 chips will fail to do both at once. Even this is
ok since the command that will fail will be the second one, and thus the
common sense logic of first-come-first-served is preserved for BLE
requests.
Signed-off-by: Dmitry Grinberg <dmitrygr@google.com>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
net/bluetooth/l2cap_core.c: In function l2cap_ecred_conn_req:
net/bluetooth/l2cap_core.c:5848:6: warning: variable credits set but not used [-Wunused-but-set-variable]
commit 15f02b9105 ("Bluetooth: L2CAP: Add initial code for Enhanced Credit Based Mode")
involved this unused variable, remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Smatch complains about the indenting:
net/bluetooth/l2cap_sock.c:1027 l2cap_sock_recvmsg()
warn: inconsistent indenting
It looks like this is supposed to be an "else if" condition.
Fixes: 15f02b9105 ("Bluetooth: L2CAP: Add initial code for Enhanced Credit Based Mode")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In bluetooth core specification 4.2,
Vol 2, Part E, 7.8.9 LE Set Advertise Enable Command, it says
The Controller shall continue advertising until ...
or until a connection is created or ...
In these cases, advertising is then disabled.
Hence, advertising would be disabled before a connection is
established. In current kernel implementation, advertising would
be re-enabled when all connections are terminated.
The correct disconnection flow looks like
< HCI Command: Disconnect
> HCI Event: Command Status
Status: Success
> HCI Event: Disconnect Complete
Status: Success
Specifically, the last Disconnect Complete Event would trigger a
callback function hci_event.c:hci_disconn_complete_evt() to
cleanup the connection and re-enable advertising when proper.
However, sometimes, there might occur an exception in the controller
when disconnection is being executed. The disconnection flow might
then look like
< HCI Command: Disconnect
> HCI Event: Command Status
Status: Unknown Connection Identifier
Note that "> HCI Event: Disconnect Complete" is missing when such an
exception occurs. This would result in advertising staying disabled
forever since the connection in question is not cleaned up correctly.
To fix the controller exception issue, we need to do some connection
cleanup when the disconnect command status indicates an error.
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To prevent spurious wake ups, we disable any discovery or advertising
when we enter suspend and restore it when we exit suspend. While paused,
we disable any management requests to modify discovery or advertising.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To handle LE devices, we must first disable passive scanning and
disconnect all connected devices. Once that is complete, we update the
whitelist and re-enable scanning
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To handle BR/EDR devices, we first disable page scan and disconnect all
connected devices. Once that is complete, we add event filters (for
devices that can wake the system) and re-enable page scan.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Register for PM_SUSPEND_PREPARE and PM_POST_SUSPEND to make sure the
Bluetooth controller is prepared correctly for suspend/resume. Implement
the registration, scheduling and task handling portions only in this
patch.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If an error occurs during request building in add_advertising(),
remember to send MGMT_STATUS_FAILED command status back to bluetoothd.
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change fixes the off by one error in the erroneous command bit
masks which can lead to the erroneous data commands being sent to a
controller that doesn't support them.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the RPA generation fails, indicate the error with a device specifc
error message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This should make it safe to have the code upstream without affecting
stable systems since there are a few details not sort out with ECRED
mode e.g: how to initiate multiple connections at once.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds the initial code for Enhanced Credit Based Mode which
introduces a new socket mode called L2CAP_MODE_EXT_FLOWCTL, which for
the most part work the same as L2CAP_MODE_LE_FLOWCTL but uses different
PDUs to setup the connections and also works over BR/EDR.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Increment the mgmt revision due to the recently added setting and
command.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This change introduces a wide band speech setting which allows higher
level clients to query the local controller support for wide band speech
as well as set the setting state when the radio is powered off.
Internally, this setting controls if erroneous data reporting is enabled
on the controller.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull when parsing signalling PDUs so skb->data for
pointing to the current PDU and skb->len as the remaining bytes to be
processed.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When processing SCO packets, the handle is wrongly assumed as 16-bit
value. The actual size is 12-bits and the other 4-bits are used for
packet flags.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some controllers have been observed to send zero'd events under some
conditions. This change guards against this condition as well as adding
a trace to facilitate diagnosability of this condition.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch provides a mechanism for MGMT interface client to query the
capability of the controller to support WBS.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Disabling LE_LEGACY_ADV when LE_EXT_ADV is enabled causes 'command
disallowed . This patch fixes that issue and disables EXT_ADV if
enabled.
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Extended advertising Data is set during bluetooth initialization
by default which causes InvalidHCICommandParameters when setting
Extended advertising parameters.
As per Core Spec 5.2 Vol 2, PART E, Sec 7.8.53, for
advertising_event_property LE_LEGACY_ADV_DIRECT_IND does not
supports advertising data when the advertising set already
contains some, the controller shall return erroc code
'InvalidHCICommandParameters(0x12).
So it is required to remove adv set for handle 0x00. since we use
instance 0 for directed adv.
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In function hci_is_blocked_key() RCU list is traversed with
list_for_each_entry() in RCU read-side CS.
Use list_for_each_entry_rcu() instead.
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fix the issue: warning:variable 'passkey' is uninitialized
when used here
Link: https://groups.google.com/forum/#!topic/clang-built-linux/kyRKCjRsGoU
Fixes: cee5f20fec ("Bluetooth: secure bluetooth stack from bluedump attack")
Reported-by: kbuild test robot <lkp@intel.com>
Suggested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Howard Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
