When comparing two pages read from different legs of a mirror, only
compare the bytes that were read, not the whole page.
In most cases we read a whole page, but in some cases with
bad blocks or odd sizes devices we might read fewer than that.
This bug has been present "forever" but at worst it might cause
a report of two many mismatches and generate a little bit
extra resync IO, so there is no need to back-port to -stable
kernels.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When create a raid5 using assume-clean and echo check or repair to
sync_action.Then component disks did not operated IO but the raid
check/resync faster than normal.
Because the judgement in function analyse_stripe():
if (do_recovery ||
sh->sector >= conf->mddev->recovery_cp)
s->syncing = 1;
else
s->replacing = 1;
When check or repair,the recovery_cp == MaxSectore,so syncing equal zero
not one.
This bug was introduced by commit 9a3e1101b8
md/raid5: detect and handle replacements during recovery.
so this patch is suitable for 3.3-stable.
Cc: stable@vger.kernel.org
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Because rde->nr_pending > 0,so can not remove this disk.
And in any case, we aren't holding rcu_read_lock()
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
raid1 arrays do not have the notion of chunk size. Calculate the
largest chunk sector size we can use to avoid a divide by zero OOPS
when aligning the size of the new array to the chunk size.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
1/ We can only treat a known-bad-block like a read-error if we
have the data that belongs in that block. So fix that test.
2/ If we cannot recovery a stripe due to insufficient data,
don't tell "md_done_sync" that the sync failed unless we really
did fail something. If we successfully record bad blocks,
that is success.
Reported-by: "majianpeng" <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This device-mapper target creates a read-only device that transparently
validates the data on one underlying device against a pre-generated tree
of cryptographic checksums stored on a second device.
Two checksum device formats are supported: version 0 which is already
shipping in Chromium OS and version 1 which incorporates some
improvements.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Signed-off-by: Will Drewry <wad@chromium.org>
Signed-off-by: Elly Jones <ellyjones@chromium.org>
Cc: Milan Broz <mbroz@redhat.com>
Cc: Olof Johansson <olofj@chromium.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch introduces a new function dm_bufio_prefetch. It prefetches
the specified range of blocks into dm-bufio cache without waiting
for i/o completion.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add dm thin target arguments to control discard support.
ignore_discard: Disables discard support
no_discard_passdown: Don't pass discards down to the underlying data
device, but just remove the mapping within the thin provisioning target.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Support discards in the thin target.
On discard the corresponding mapping(s) are removed from the thin
device. If the associated block(s) are no longer shared the discard
is passed to the underlying device.
All bios other than discards now have an associated deferred_entry
that is saved to the 'all_io_entry' in endio_hook. When non-discard
IO completes and associated mappings are quiesced any discards that
were deferred, via ds_add_work() in process_discard(), will be queued
for processing by the worker thread.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
drivers/md/dm-thin.c | 173 ++++++++++++++++++++++++++++++++++++++++++++++----
drivers/md/dm-thin.c | 172 ++++++++++++++++++++++++++++++++++++++++++++++-----
1 file changed, 158 insertions(+), 14 deletions(-)
This patch contains the ground work needed for dm-thin to support discard.
- Adds endio function that replaces shared_read_endio.
- Introduce an explicit 'quiesced' flag into the new_mapping structure.
Before, this was implicitly indicated by m->list being empty.
- The map_info->ptr remains constant for the duration of a bio's trip
through the thin target. Make it easier to reason about it.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Support the use of an external _read only_ device as an origin for a thin
device.
Any read to an unprovisioned area of the thin device will be passed
through to the origin. Writes trigger allocation of new blocks as
usual.
One possible use case for this would be VM hosts that want to run
guests on thinly-provisioned volumes but have the base image on another
device (possibly shared between many VMs).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The thin metadata format can only make use of a device that is <=
THIN_METADATA_MAX_SECTORS (currently 15.9375 GB). Therefore, there is no
practical benefit to using a larger device.
However, it may be that other factors impose a certain granularity for
the space that is allocated to a device (E.g. lvm2 can impose a coarse
granularity through the use of large, >= 1 GB, physical extents).
Rather than reject a larger metadata device, during thin-pool device
construction, switch to allowing it but issue a warning if a device
larger than THIN_METADATA_MAX_SECTORS_WARNING (16 GB) is
provided. Any space over 15.9375 GB will not be used.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Save space by removing entries from the space map ref_count tree if
they're no longer needed.
Ref counts are stored in two places: a bitmap if the ref_count is
below 3, or a btree of uint32_t if 3 or above.
When a ref_count that was above 3 drops below we can remove it from
the tree and save some metadata space. This removal was commented out
before because I was unsure why this was causing under-populated btree
nodes. Earlier patches have fixed this issue.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Commit unwritten data every second to prevent too much building up.
Released blocks don't become available until after the next commit
(for crash resilience). Prior to this patch commits were only
triggered by a message to the target or a REQ_{FLUSH,FUA} bio. This
allowed far too big a position to build up.
The interval is hard-coded to 1 second. This is a sensible setting.
I'm not making this user configurable, since there isn't much to be
gained by tweaking this - and a lot lost by setting it far too high.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Device mapper uses sscanf to convert arguments to numbers. The problem is that
the way we use it ignores additional unmatched characters in the scanned string.
For example, this `if (sscanf(string, "%d", &number) == 1)' will match a number,
but also it will match number with some garbage appended, like "123abc".
As a result, device mapper accepts garbage after some numbers. For example
the command `dmsetup create vg1-new --table "0 16384 linear 254:1bla 34816bla"'
will pass without an error.
This patch fixes all sscanf uses in device mapper. It appends "%c" with
a pointer to a dummy character variable to every sscanf statement.
The construct `if (sscanf(string, "%d%c", &number, &dummy) == 1)' succeeds
only if string is a null-terminated number (optionally preceded by some
whitespace characters). If there is some character appended after the number,
sscanf matches "%c", writes the character to the dummy variable and returns 2.
We check the return value for 1 and consequently reject numbers with some
garbage appended.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The dm-raid code currently fails to create a RAID array if any of the
superblocks cannot be read. This was an oversight as there is already
code to handle this case if the values ('- -') were provided for the
failed array position.
With this patch, if a superblock cannot be read, the array position's
fields are initialized as though '- -' was set in the table. That is,
the device is failed and the position should not be used, but if there
is sufficient redundancy, the array should still be activated.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix a harmless typo.
The root is a chunk of data that gets written to the superblock. This
data is used to recreate the space map when opening a metadata area.
We have two space maps; one tracking space on the metadata device and
one of the data device. Both of these use the same format for their
root, so this typo was harmless.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Now that the value_size is held within every node of the btrees we can
remove this argument from value_ptr().
For the last few months a BUG_ON has been checking this argument is
the same as that held in the node. No issues were reported. So this
is a safe change.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The map_context pointer should always be set. However, we have reports
that upon requeuing it is not set correctly. So add set and clear
functions with a BUG_ON() to track the issue properly.
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Tested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
As a precaution, set bi_end_io to NULL when failing to remap.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
free_devices in dm_table.c already uses list_for_each(), so we don't
need to check if the list is empty.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove documentation for unimplemented 'trim' message.
I'd planned a 'trim' target message for shrinking thin devices, but
this is better handled via the discard ioctl.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The dm raid module (using md) is becoming the preferred way of creating long-lived
mirrors through userspace LVM so remove the EXPERIMENTAL tag.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Drop EXPERIMENTAL tag from dm-uevent.
It's not changed for a while and some userspace tools are relying upon it.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When we remove an entry from a node we sometimes rebalance with it's
two neighbours. This wasn't being done correctly; in some cases
entries have to move all the way from the right neighbour to the left
neighbour, or vice versa. This patch pretty much re-writes the
balancing code to fix it.
This code is barely used currently; only when you delete a thin
device, and then only if you have hundreds of them in the same pool.
Once we have discard support, which removes mappings, this will be used
much more heavily.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Avoid using the bi_next field for the holder of a cell when deferring
bios because a stacked device below might change it. Store the
holder in a new field in struct cell instead.
When a cell is created, the bio that triggered creation (the holder) was
added to the same bio list as subsequent bios. In some cases we pass
this holder bio directly to devices underneath. If those devices use
the bi_next field there will be trouble...
This also simplifies some code that had to work out which bio was the
holder.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Always set io->error to -EIO when an error is detected in dm-crypt.
There were cases where an error code would be set only if we finish
processing the last sector. If there were other encryption operations in
flight, the error would be ignored and bio would be returned with
success as if no error happened.
This bug is present in kcryptd_crypt_write_convert, kcryptd_crypt_read_convert
and kcryptd_async_done.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Reviewed-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch fixes a possible deadlock in dm-crypt's mempool use.
Currently, dm-crypt reserves a mempool of MIN_BIO_PAGES reserved pages.
It allocates first MIN_BIO_PAGES with non-failing allocation (the allocation
cannot fail and waits until the mempool is refilled). Further pages are
allocated with different gfp flags that allow failing.
Because allocations may be done in parallel, this code can deadlock. Example:
There are two processes, each tries to allocate MIN_BIO_PAGES and the processes
run simultaneously.
It may end up in a situation where each process allocates (MIN_BIO_PAGES / 2)
pages. The mempool is exhausted. Each process waits for more pages to be freed
to the mempool, which never happens.
To avoid this deadlock scenario, this patch changes the code so that only
the first page is allocated with non-failing gfp mask. Allocation of further
pages may fail.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Call the correct exit function on failure in dm_exception_store_init.
Signed-off-by: Andrei Warkentin <andrey.warkentin@gmail.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mostly tidying up code in preparation for some bigger changes
next time.
A few bug fixes tagged for -stable.
Main functionality change is that some RAID10 arrays can now
grow to use extra space that may have been made available on the
individual devices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=MGuM
-----END PGP SIGNATURE-----
Merge tag 'md-3.4' of git://neil.brown.name/md
Pull md updates for 3.4 from Neil Brown:
"Mostly tidying up code in preparation for some bigger changes next
time.
A few bug fixes tagged for -stable.
Main functionality change is that some RAID10 arrays can now grow to
use extra space that may have been made available on the individual
devices."
Fixed up trivial conflicts with the k[un]map_atomic() cleanups in
drivers/md/bitmap.c.
* tag 'md-3.4' of git://neil.brown.name/md: (22 commits)
md: Add judgement bb->unacked_exist in function md_ack_all_badblocks().
md: fix clearing of the 'changed' flags for the bad blocks list.
md/bitmap: discard CHUNK_BLOCK_SHIFT macro
md/bitmap: remove unnecessary indirection when allocating.
md/bitmap: remove some pointless locking.
md/bitmap: change a 'goto' to a normal 'if' construct.
md/bitmap: move printing of bitmap status to bitmap.c
md/bitmap: remove some unused noise from bitmap.h
md/raid10 - support resizing some RAID10 arrays.
md/raid1: handle merge_bvec_fn in member devices.
md/raid10: handle merge_bvec_fn in member devices.
md: add proper merge_bvec handling to RAID0 and Linear.
md: tidy up rdev_for_each usage.
md/raid1,raid10: avoid deadlock during resync/recovery.
md/bitmap: ensure to load bitmap when creating via sysfs.
md: don't set md arrays to readonly on shutdown.
md: allow re-add to failed arrays.
md/raid5: use atomic_dec_return() instead of atomic_dec() and atomic_read().
md: Use existed macros instead of numbers
md/raid5: removed unused 'added_devices' variable.
...
Pull kmap_atomic cleanup from Cong Wang.
It's been in -next for a long time, and it gets rid of the (no longer
used) second argument to k[un]map_atomic().
Fix up a few trivial conflicts in various drivers, and do an "evil
merge" to catch some new uses that have come in since Cong's tree.
* 'kmap_atomic' of git://github.com/congwang/linux: (59 commits)
feature-removal-schedule.txt: schedule the deprecated form of kmap_atomic() for removal
highmem: kill all __kmap_atomic() [swarren@nvidia.com: highmem: Fix ARM build break due to __kmap_atomic rename]
drbd: remove the second argument of k[un]map_atomic()
zcache: remove the second argument of k[un]map_atomic()
gma500: remove the second argument of k[un]map_atomic()
dm: remove the second argument of k[un]map_atomic()
tomoyo: remove the second argument of k[un]map_atomic()
sunrpc: remove the second argument of k[un]map_atomic()
rds: remove the second argument of k[un]map_atomic()
net: remove the second argument of k[un]map_atomic()
mm: remove the second argument of k[un]map_atomic()
lib: remove the second argument of k[un]map_atomic()
power: remove the second argument of k[un]map_atomic()
kdb: remove the second argument of k[un]map_atomic()
udf: remove the second argument of k[un]map_atomic()
ubifs: remove the second argument of k[un]map_atomic()
squashfs: remove the second argument of k[un]map_atomic()
reiserfs: remove the second argument of k[un]map_atomic()
ocfs2: remove the second argument of k[un]map_atomic()
ntfs: remove the second argument of k[un]map_atomic()
...
Pull trivial tree from Jiri Kosina:
"It's indeed trivial -- mostly documentation updates and a bunch of
typo fixes from Masanari.
There are also several linux/version.h include removals from Jesper."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (101 commits)
kcore: fix spelling in read_kcore() comment
constify struct pci_dev * in obvious cases
Revert "char: Fix typo in viotape.c"
init: fix wording error in mm_init comment
usb: gadget: Kconfig: fix typo for 'different'
Revert "power, max8998: Include linux/module.h just once in drivers/power/max8998_charger.c"
writeback: fix fn name in writeback_inodes_sb_nr_if_idle() comment header
writeback: fix typo in the writeback_control comment
Documentation: Fix multiple typo in Documentation
tpm_tis: fix tis_lock with respect to RCU
Revert "media: Fix typo in mixer_drv.c and hdmi_drv.c"
Doc: Update numastat.txt
qla4xxx: Add missing spaces to error messages
compiler.h: Fix typo
security: struct security_operations kerneldoc fix
Documentation: broken URL in libata.tmpl
Documentation: broken URL in filesystems.tmpl
mtd: simplify return logic in do_map_probe()
mm: fix comment typo of truncate_inode_pages_range
power: bq27x00: Fix typos in comment
...
If there are no unacked bad blocks, then there is no point searching
for them to acknowledge them.
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In super_1_sync (the first hunk) we need to clear 'changed' before
checking read_seqretry(), otherwise we might race with other code
adding a bad block and so won't retry later.
In md_update_sb (the second hunk), in the case where there is no
metadata (neither persistent nor external), we treat any bad blocks as
an error. However we need to clear the 'changed' flag before calling
md_ack_all_badblocks, else it won't do anything.
This patch is suitable for -stable release 3.0 and later.
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Be redefining ->chunkshift as the shift from sectors to chunks rather
than bytes to chunks, we can just use "bitmap->chunkshift" which is
shorter than the macro call, and less indirect.
Signed-off-by: NeilBrown <neilb@suse.de>
These funcitons don't add anything useful except possibly the trace
points, and I don't think they are worth the extra indirection.
So remove them.
Signed-off-by: NeilBrown <neilb@suse.de>
There is nothing gained by holding a lock while we check if a pointer
is NULL or not. If there could be a race, then it could become NULL
immediately after the unlock - but there is no race here.
So just remove the locking.
Signed-off-by: NeilBrown <neilb@suse.de>
The use of a goto makes the control flow more obscure here.
So make it a normal:
if (x) {
Y;
}
No functional change.
Signed-off-by: NeilBrown <neilb@suse.de>
The part of /proc/mdstat which describes the bitmap should really
be generated by code in bitmap.c. So move it there.
Signed-off-by: NeilBrown <neilb@suse.de>
'resizing' an array in this context means making use of extra
space that has become available in component devices, not adding new
devices.
It also includes shrinking the array to take up less space of
component devices.
This is not supported for array with a 'far' layout. However
for 'near' and 'offset' layout arrays, adding and removing space at
the end of the devices is easy to support, and this patch provides
that support.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently we don't honour merge_bvec_fn in member devices so if there
is one, we force all requests to be single-page at most.
This is not ideal.
So create a raid1 merge_bvec_fn to check that function in children
as well.
This introduces a small problem. There is no locking around calls
the ->merge_bvec_fn and subsequent calls to ->make_request. So a
device added between these could end up getting a request which
violates its merge_bvec_fn.
Currently the best we can do is synchronize_sched(). This will work
providing no preemption happens. If there is is preemption, we just
have to hope that new devices are largely consistent with old devices.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently we don't honour merge_bvec_fn in member devices so if there
is one, we force all requests to be single-page at most.
This is not ideal.
So enhance the raid10 merge_bvec_fn to check that function in children
as well.
This introduces a small problem. There is no locking around calls
the ->merge_bvec_fn and subsequent calls to ->make_request. So a
device added between these could end up getting a request which
violates its merge_bvec_fn.
Currently the best we can do is synchronize_sched(). This will work
providing no preemption happens. If there is preemption, we just
have to hope that new devices are largely consistent with old devices.
Signed-off-by: NeilBrown <neilb@suse.de>
These personalities currently set a max request size of one page
when any member device has a merge_bvec_fn because they don't
bother to call that function.
This causes extra works in splitting and combining requests.
So make the extra effort to call the merge_bvec_fn when it exists
so that we end up with larger requests out the bottom.
Signed-off-by: NeilBrown <neilb@suse.de>
md.h has an 'rdev_for_each()' macro for iterating the rdevs in an
mddev. However it uses the 'safe' version of list_for_each_entry,
and so requires the extra variable, but doesn't include 'safe' in the
name, which is useful documentation.
Consequently some places use this safe version without needing it, and
many use an explicity list_for_each entry.
So:
- rename rdev_for_each to rdev_for_each_safe
- create a new rdev_for_each which uses the plain
list_for_each_entry,
- use the 'safe' version only where needed, and convert all other
list_for_each_entry calls to use rdev_for_each.
Signed-off-by: NeilBrown <neilb@suse.de>
If RAID1 or RAID10 is used under LVM or some other stacking
block device, it is possible to enter a deadlock during
resync or recovery.
This can happen if the upper level block device creates
two requests to the RAID1 or RAID10. The first request gets
processed, blocks recovery and queue requests for underlying
requests in current->bio_list. A resync request then starts
which will wait for those requests and block new IO.
But then the second request to the RAID1/10 will be attempted
and it cannot progress until the resync request completes,
which cannot progress until the underlying device requests complete,
which are on a queue behind that second request.
So allow that second request to proceed even though there is
a resync request about to start.
This is suitable for any -stable kernel.
Cc: stable@vger.kernel.org
Reported-by: Ray Morris <support@bettercgi.com>
Tested-by: Ray Morris <support@bettercgi.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When commit 69e51b449d (md/bitmap: separate out loading a bitmap...)
created bitmap_load, it missed calling it after bitmap_create when a
bitmap is created through the sysfs interface.
So if a bitmap is added this way, we don't allocate memory properly
and can crash.
This is suitable for any -stable release since 2.6.35.
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
It seems that with recent kernel, writeback can still be happening
while shutdown is happening, and consequently data can be written
after the md reboot notifier switches all arrays to read-only.
This causes a BUG.
So don't switch them to read-only - just mark them clean and
set 'safemode' to '2' which mean that immediately after any
write the array will be switch back to 'clean'.
This could result in the shutdown happening when array is marked
dirty, thus forcing a resync on reboot. However if you reboot
without performing a "sync" first, you get to keep both halves.
This is suitable for any stable kernel (though there might be some
conflicts with obvious fixes in earlier kernels).
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
When an array is failed (some data inaccessible) then there is no
point attempting to add a spare as it could not possibly be recovered.
However that may be value in re-adding a recently removed device.
e.g. if there is a write-intent-bitmap and it is clear, then access
to the data could be restored by this action.
So don't reject a re-add to a failed array for RAID10 and RAID5 (the
only arrays types that check for a failed array).
Signed-off-by: NeilBrown <neilb@suse.de>
Recent commit 4ca40c2ce0 (md/raid10: Allow replacement device ...)
added an smp_mb in end_sync_write.
This was to close a possible race with raid10_remove_disk.
However there is no such race as it is never attempted to remove a
disk while resync (or recovery) is happening.
so the smp_mb is just noise.
Signed-off-by: NeilBrown <neilb@suse.de>
Fix dm-raid flush support.
Both md and dm have support for flush, but the dm-raid target
forgot to set the flag to indicate that flushes should be
passed on. (Important for data integrity e.g. with writeback cache
enabled.)
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The 'rebuild' parameter is used to rebuild individual devices in an
array (e.g. resynchronize a RAID1 device or recalculate a parity device
in higher RAID). The MD_CHANGE_DEVS flag must be set when this
parameter is given in order to write out the superblocks and make the
change take immediate effect. The code that handles new devices in
super_load already sets MD_CHANGE_DEVS and 'FirstUse'. (The 'FirstUse'
flag was being set as a special case for rebuilds in
super_init_validation.)
Add a condition for rebuilds in super_load to take care of both flags
without the special case in 'super_init_validation'.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Correct the number of mapped sectors shown on a thin device's
status line by decrementing td->mapped_blocks in __remove() each time
a block is removed.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If dm_sm_disk_create() fails the superblock must be unlocked.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The __open_device() error paths in __create_thin() and __create_snap()
incorrectly call __close_device() even if td was not initialized by
__open_device(). Remove this.
Also document __open_device() return values, remove a redundant
td->changed = 1 in __create_thin(), and insert an additional
safeguard against creating an already-existing device.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The following BUG is hit on the first read that is submitted to a dm
flakey test device while the device is "down" if the corrupt_bio_byte
feature wasn't requested when the device's table was loaded.
Example DM table that will hit this BUG:
0 2097152 flakey 8:0 2048 0 30
This bug was introduced by commit a3998799fb
(dm flakey: add corrupt_bio_byte feature) in v3.1-rc1.
BUG: unable to handle kernel paging request at ffff8801cfce3fff
IP: [<ffffffffa008c233>] corrupt_bio_data+0x6e/0xae [dm_flakey]
PGD 1606063 PUD 0
Oops: 0002 [#1] SMP
...
Call Trace:
<IRQ>
[<ffffffffa008c2b5>] flakey_end_io+0x42/0x48 [dm_flakey]
[<ffffffffa00dca98>] clone_endio+0x54/0xb6 [dm_mod]
[<ffffffff81130587>] bio_endio+0x2d/0x2f
[<ffffffff811c819a>] req_bio_endio+0x96/0x9f
[<ffffffff811c94b9>] blk_update_request+0x1dc/0x3a9
[<ffffffff812f5ee2>] ? rcu_read_unlock+0x21/0x23
[<ffffffff811c96a6>] blk_update_bidi_request+0x20/0x6e
[<ffffffff811c9713>] blk_end_bidi_request+0x1f/0x5d
[<ffffffff811c978d>] blk_end_request+0x10/0x12
[<ffffffff8128f450>] scsi_io_completion+0x1e5/0x4b1
[<ffffffff812882a9>] scsi_finish_command+0xec/0xf5
[<ffffffff8128f830>] scsi_softirq_done+0xff/0x108
[<ffffffff811ce284>] blk_done_softirq+0x84/0x98
[<ffffffff81048d19>] __do_softirq+0xe3/0x1d5
[<ffffffff8138f83f>] ? _raw_spin_lock+0x62/0x69
[<ffffffff810997cf>] ? handle_irq_event+0x4c/0x61
[<ffffffff8139833c>] call_softirq+0x1c/0x30
[<ffffffff81003b37>] do_softirq+0x4b/0xa3
[<ffffffff81048a39>] irq_exit+0x53/0xca
[<ffffffff81398acd>] do_IRQ+0x9d/0xb4
[<ffffffff81390333>] common_interrupt+0x73/0x73
...
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.1+
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch fixes a crash by recognising discards in dm_io.
Currently dm_mirror can send REQ_DISCARD bios if running over a
discard-enabled device and without support in dm_io the system
crashes badly.
BUG: unable to handle kernel paging request at 00800000
IP: __bio_add_page.part.17+0xf5/0x1e0
...
bio_add_page+0x56/0x70
dispatch_io+0x1cf/0x240 [dm_mod]
? km_get_page+0x50/0x50 [dm_mod]
? vm_next_page+0x20/0x20 [dm_mod]
? mirror_flush+0x130/0x130 [dm_mirror]
dm_io+0xdc/0x2b0 [dm_mod]
...
Introduced in 2.6.38-rc1 by commit 5fc2ffeabb
(dm raid1: support discard).
Signed-off-by: Milan Broz <mbroz@redhat.com>
Cc: stable@kernel.org
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If 'argc' is zero we jump to the 'out:' label, but this leaks the
(unused) memory that 'dm_split_args()' allocated for 'argv' if the
string being split consisted entirely of whitespace. Jump to the
'out_argv:' label instead to free up that memory.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
2 relate to the recently added drive replacement.
One causes read error in RAID10 to sometimes be retried indefinitely.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=93ms
-----END PGP SIGNATURE-----
Merge tag 'md-3.3-fixes' of git://neil.brown.name/md
Pull md fixes from Neil Brown:
"Three fixes for md in 3.3-rc: Two relate to the recently added drive
replacement. One fixes the problem where a read error in RAID10 would
sometimes be retried indefinitely."
* tag 'md-3.3-fixes' of git://neil.brown.name/md:
md/raid10: fix assembling of arrays with replacement devices.
md/raid10: fix handling of error on last working device in array.
md/raid1: fix buglet in md_raid1_contested.
commit 56a2559bb6 (md/raid10: recognise replacements ...)
changed 'run' to set ->replacement or ->rdev depending on the
'Replacement' status if the device, but it didn't remove the
old unconditional setting of 'rdev'. So it was largely ineffective.
So remove that now.
Signed-off-by: NeilBrown <neilb@suse.de>
If we get a read error on the last working device in a RAID10 which
contains the target block, then we don't fail the device (which is
good) but we don't abort retries, which is wrong.
We end up in an infinite loop retrying the read on the one device.
This patch fixes the problem in two places:
1/ in raid10_end_read_request we don't even ask for a retry if this
was the last usable device. This is efficient but a little racy
and will sometimes retry when it should not.
2/ in handle_read_error we are careful to exclude any device from
retry which we tried to mark as faulty (that might have failed if
it was the last device). This is race-free but less efficient.
Signed-off-by: NeilBrown <neilb@suse.de>
Since we added 'replacement' capability, RAID1 can have twice
as many devices as ->raid_disks indicates.
So md_raid1_congested needs to check that many possible devices,
not just ->raid_disks many.
Signed-off-by: NeilBrown <neilb@suse.de>
1/ two small fixes to ensure we handle an interrupted resync properly.
2/ avoid loading the bitmap multiple times in dm-raid
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=k0Xz
-----END PGP SIGNATURE-----
Merge tag 'md-3.3-fixes' of git://neil.brown.name/md
Some simple md-related fixes.
1/ two small fixes to ensure we handle an interrupted resync properly.
2/ avoid loading the bitmap multiple times in dm-raid
* tag 'md-3.3-fixes' of git://neil.brown.name/md:
md: two small fixes to handling interrupt resync.
Prevent DM RAID from loading bitmap twice.
1/ If a resync is aborted we should record how far we got
(recovery_cp) the last request that we know has completed
(->curr_resync_completed) rather than the last request that was
submitted (->curr_resync).
2/ When a resync aborts we still want to update the metadata with
any changes, so set MD_CHANGE_DEVS even if we 'skip'.
Signed-off-by: NeilBrown <neilb@suse.de>
As 'make versioncheck' points out, drivers/md/dm-bufio.c has no need to include
linux/version.h, so this patch removes the unneeded include.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The life cycle of a device-mapper target is:
1) create
2) resume
3) suspend
*) possibly repeat from 2
4) destroy
The dm-raid target is unconditionally calling MD's bitmap_load function upon
every resume. If steps 2 & 3 above are repeated, bitmap_load is called
multiple times. It is only written to be called once; otherwise, it allocates
new memory for the bitmap (without freeing the old) and incrementing the number
of pages it thinks it has without zeroing first. This ultimately leads to
access beyond allocated memory and lost memory.
Simply avoiding the bitmap_load call upon resume is not sufficient. If the
target was suspended while the initial recovery was only partially complete,
it needs to be restarted when the target is resumed. This is why
'md_wakeup_thread' is called before issuing the 'mddev_resume'.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
* 'for-3.3/core' of git://git.kernel.dk/linux-block: (37 commits)
Revert "block: recursive merge requests"
block: Stop using macro stubs for the bio data integrity calls
blockdev: convert some macros to static inlines
fs: remove unneeded plug in mpage_readpages()
block: Add BLKROTATIONAL ioctl
block: Introduce blk_set_stacking_limits function
block: remove WARN_ON_ONCE() in exit_io_context()
block: an exiting task should be allowed to create io_context
block: ioc_cgroup_changed() needs to be exported
block: recursive merge requests
block, cfq: fix empty queue crash caused by request merge
block, cfq: move icq creation and rq->elv.icq association to block core
block, cfq: restructure io_cq creation path for io_context interface cleanup
block, cfq: move io_cq exit/release to blk-ioc.c
block, cfq: move icq cache management to block core
block, cfq: move io_cq lookup to blk-ioc.c
block, cfq: move cfqd->icq_list to request_queue and add request->elv.icq
block, cfq: reorganize cfq_io_context into generic and cfq specific parts
block: remove elevator_queue->ops
block: reorder elevator switch sequence
...
Fix up conflicts in:
- block/blk-cgroup.c
Switch from can_attach_task to can_attach
- block/cfq-iosched.c
conflict with now removed cic index changes (we now use q->id instead)
A logical volume can map to just part of underlying physical volume.
In this case, it must be treated like a partition.
Based on a patch from Alasdair G Kergon.
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One is a recently introduced regression that affects an unusual
configuration with a guaranteed BUG_ON. Has been tagged for -stable.
The other is minor missing functionality.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=969y
-----END PGP SIGNATURE-----
Merge tag 'md-3.3-fixes' of git://neil.brown.name/md
Two bugfixes for md.
One is a recently introduced regression that affects an unusual
configuration with a guaranteed BUG_ON. Has been tagged for -stable.
The other is minor missing functionality.
* tag 'md-3.3-fixes' of git://neil.brown.name/md:
md/raid1: perform bad-block tests for WriteMostly devices too.
md: notify the 'degraded' sysfs attribute on failure.
Stacking driver queue limits are typically bounded exclusively by the
capabilities of the low level devices, not by the stacking driver
itself.
This patch introduces blk_set_stacking_limits() which has more liberal
metrics than the default queue limits function. This allows us to
inherit topology parameters from bottom devices without manually
tweaking the default limits in each driver prior to calling the stacking
function.
Since there is now a clear distinction between stacking and low-level
devices, blk_set_default_limits() has been modified to carry the more
conservative values that we used to manually set in
blk_queue_make_request().
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We normally try to avoid reading from write-mostly devices, but when
we do we really have to check for bad blocks and be sure not to
try reading them.
With the current code, best_good_sectors might not get set and that
causes zero-length read requests to be send down which is very
confusing.
This bug was introduced in commit d2eb35acfd and so the patch
is suitable for 3.1.x and 3.2.x
Reported-and-tested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reported-and-tested-by: Art -kwaak- van Breemen <ard@telegraafnet.nl>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@vger.kernel.org
We currently only 'notify' changes to the 'degraded' attribute
when it decreases, not when it increases.
Notifying on failure is a little awkward as it happen in
interrupt context.
So instead, notify when we remove the failed device from the array,
which is very soon afterwards.
Reported-and-tested-by: Mikhail Balabin <mbalabin@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Big change is new hot-replacement.
A slot in an array can hold 2 devices - one that
wants-replacement and one that is the replacement.
Once the replacement is built - either from the
original or (in the case of errors) from elsewhere,
the wants-replacement device will be removed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=j00/
-----END PGP SIGNATURE-----
Merge tag 'md-3.3' of git://neil.brown.name/md
md update for 3.3
Big change is new hot-replacement.
A slot in an array can hold 2 devices - one that
wants-replacement and one that is the replacement.
Once the replacement is built - either from the
original or (in the case of errors) from elsewhere,
the wants-replacement device will be removed.
* tag 'md-3.3' of git://neil.brown.name/md: (36 commits)
md/raid1: Mark device want_replacement when we see a write error.
md/raid1: If there is a spare and a want_replacement device, start replacement.
md/raid1: recognise replacements when assembling arrays.
md/raid1: handle activation of replacement device when recovery completes.
md/raid1: Allow a failed replacement device to be removed.
md/raid1: Allocate spare to store replacement devices and their bios.
md/raid1: Replace use of mddev->raid_disks with conf->raid_disks.
md/raid10: If there is a spare and a want_replacement device, start replacement.
md/raid10: recognise replacements when assembling array.
md/raid10: Allow replacement device to be replace old drive.
md/raid10: handle recovery of replacement devices.
md/raid10: Handle replacement devices during resync.
md/raid10: writes should get directed to replacement as well as original.
md/raid10: allow removal of failed replacement devices.
md/raid10: preferentially read from replacement device if possible.
md/raid10: change read_balance to return an rdev
md/raid10: prepare data structures for handling replacement.
md/raid5: Mark device want_replacement when we see a write error.
md/raid5: If there is a spare and a want_replacement device, start replacement.
md/raid5: recognise replacements when assembling array.
...
Move invalidate_bdev, block_sync_page into fs/block_dev.c. Export
kill_bdev as well, so brd doesn't have to open code it. Reduce
buffer_head.h requirement accordingly.
Removed a rather large comment from invalidate_bdev, as it looked a bit
obsolete to bother moving. The small comment replacing it says enough.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Now that WantReplacement drives are replaced cleanly, mark a drive
as want_replacement when we see a write error. It might get failed soon so
the WantReplacement flag is irrelevant, but if the write error is recorded
in the bad block log, we still want to activate any spare that might
be available.
Signed-off-by: NeilBrown <neilb@suse.de>
When attempting to add a spare to a RAID1 array, also consider
adding it as a replacement for a want_replacement device.
Signed-off-by: NeilBrown <neilb@suse.de>
If a Replacement is seen, file it as such.
If we see two replacements (or two normal devices) for the one slot,
abort.
Signed-off-by: NeilBrown <neilb@suse.de>
When recovery completes ->spare_active is called.
This checks if the replacement is ready and if so it fails
the original.
Signed-off-by: NeilBrown <neilb@suse.de>
In RAID1, a replacement is much like a normal device, so we just
double the size of the relevant arrays and look at all possible
devices for reads and writes.
This means that the array looks like it is now double the size in some
way - we need to be careful about that.
In particular, we checking if the array is still degraded while
creating a recovery request we need to only consider the first 'half'
- i.e. the real (non-replacement) devices.
Signed-off-by: NeilBrown <neilb@suse.de>
In general mddev->raid_disks can change unexpectedly while
conf->raid_disks will only change in a very controlled way. So change
some uses of one to the other.
The use of mddev->raid_disks will not cause actually problems but
this way is more consistent and safer in the long term.
Signed-off-by: NeilBrown <neilb@suse.de>
When attempting to add a spare to a RAID10 array, also consider
adding it as a replacement for a want_replacement device.
Signed-off-by: NeilBrown <neilb@suse.de>
If a Replacement is seen, file it as such.
If we see two replacements (or two normal devices) for the one slot,
abort.
Signed-off-by: NeilBrown <neilb@suse.de>
When recovery finish and spare_active is called, check for a
replace that might have just become fully synced and mark it
as such, marking the original as failed.
Then when the original is removed, move the replacement into
its position.
This means that 'replacement' and spontaneously become NULL in some
situations. Make sure we check for those.
It also means that 'rdev' and 'replacement' could appear to be
identical - check for that too.
Signed-off-by: NeilBrown <neilb@suse.de>
If there is a replacement device, then recover to it,
reading from any drives - maybe the one being replaced, maybe not.
Signed-off-by: NeilBrown <neilb@suse.de>
If we need to resync an array which has replacement devices,
we always write any block checked to every replacement.
If the resync was bitmap-based resync we will then complete the
replacement normally.
If it was a full resync, we mark the replacements as fully recovered
when the resync finishes so no further recovery is needed.
Signed-off-by: NeilBrown <neilb@suse.de>
When writing, we need to submit two writes, one to the original,
and one to the replacements - if there is a replacement.
If the write to the replacement results in a write error we just
fail the device. We only try to record write errors to the
original.
This only handles writing new data. Writing for resync/recovery
will come later.
Signed-off-by: NeilBrown <neilb@suse.de>
When reading (for array reads, not for recovery etc) we read from the
replacement device if it has recovered far enough.
This requires storing the chosen rdev in the 'r10_bio' so we can make
sure to drop the ref on the right device when the read finishes.
Signed-off-by: NeilBrown <neilb@suse.de>
It makes more sense to return an rdev than just an index as
read_balance() gets a reference to the rdev and so returning
the pointer make this more idiomatic.
This will be needed in a future patch when we might return
a 'replacement' rdev instead of the main rdev.
Signed-off-by: NeilBrown <neilb@suse.de>
Allow each slot in the RAID10 to have 2 devices, the want_replacement
and the replacement.
Also an r10bio to have 2 bios, and for resync/recovery allocate the
second bio if there are any replacement devices.
Signed-off-by: NeilBrown <neilb@suse.de>
Now that WantReplacement drives are replaced cleanly, mark a drive
as WantReplacement when we see a write error. It might get failed soon so
the WantReplacement flag is irrelevant, but if the write error is recorded
in the bad block log, we still want to activate any spare that might
be available.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When attempting to add a spare to a RAID[456] array, also consider
adding it as a replacement for a want_replacement device.
This requires that common md code attempt hot_add even when the array
is not formally degraded.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If a Replacement is seen, file it as such.
If we see two replacements (or two normal devices) for the one slot,
abort.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When recovery completes - as reported by a call to ->spare_active,
we clear In_sync on the original and set it on the replacement.
Then when the original gets removed we move the replacement from
'replacement' to 'rdev'.
This could race with other code that is looking at these pointers,
so we use memory barriers and careful ordering to ensure that
a reader might see one device twice, but never no devices.
Then the readers guard against using both devices, which could
only happen when writing.
Signed-off-by: NeilBrown <neilb@suse.de>
During recovery we want to write to the replacement but not
the original. So we have two new flags
- R5_NeedReplace if this stripe has a replacement that needs to
be written at some stage
- R5_WantReplace if NeedReplace, and the data is available, and
a 'sync' has been requested on this stripe.
We also distinguish between 'sync and replace' which need to read
all other devices, and 'replace' which only needs to read the
devices being replaced.
Note that during resync we always write to any replacement device.
It might not need to be written to, but as we don't read to compare,
we have to write to be sure.
Signed-off-by: NeilBrown <neilb@suse.de>
When writing, we need to submit two writes, one to the original, and
one to the replacement - if there is a replacement.
If the write to the replacement results in a write error, we just fail
the device. We only try to record write errors to the original.
When writing for recovery, we shouldn't write to the original. This
will be addressed in a subsequent patch that generally addresses
recovery.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Enhance raid5_remove_disk to be able to remove ->replacement
as well as ->rdev.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If a replacement device is present and has been recovered far enough,
then use it for reading into the stripe cache.
If we get an error we don't try to repair it, we just fail the device.
A replacement device that gives errors does not sound sensible.
This requires removing the setting of R5_ReadError when we get
a read error during a read that bypasses the cache. It was probably
a bad idea anyway as we don't know that every block in the read
caused an error, and it could cause ReadError to be set for the
replacement device, which is bad.
Signed-off-by: NeilBrown <neilb@suse.de>
We current initialise some fields of a bio when preparing a
stripe_head, and again just before submitting the request.
Remove the duplication by only setting the fields that lower level
devices don't touch in raid5_build_block, and only set the changeable
fields in ops_run_io.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Remove some #defines that are no longer used, and replace some
others with an enum.
And remove an unused field.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Just enhance data structures to record a second device per slot to be
used as a 'replacement' device, replacing the original.
We also have a second bio in each slot in each stripe_head. This will
only be used when writing to the array - we need to write to both the
original and the replacement at the same time, so will need two bios.
For now, only try using the replacement drive for aligned-reads.
In this case, we prefer the replacement if it has been recovered far
enough, otherwise use the original.
This includes a small enhancement. Previously we would only do
aligned reads if the target device was fully recovered. Now we also
do them if it has recovered far enough.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
hot-replace is a feature being added to md which will allow a
device to be replaced without removing it from the array first.
With hot-replace a spare can be activated and recovery can start while
the original device is still in place, thus allowing a transition from
an unreliable device to a reliable device without leaving the array
degraded during the transition. It can also be use when the original
device is still reliable but it not wanted for some reason.
This will eventually be supported in RAID4/5/6 and RAID10.
This patch adds a super-block flag to distinguish the replacement
device. If an old kernel sees this flag it will reject the device.
It also adds two per-device flags which are viewable and settable via
sysfs.
"want_replacement" can be set to request that a device be replaced.
"replacement" is set to show that this device is replacing another
device.
The "rd%d" links in /sys/block/mdXx/md only apply to the original
device, not the replacement. We currently don't make links for the
replacement - there doesn't seem to be a need.
Signed-off-by: NeilBrown <neilb@suse.de>
Soon an array will be able to have multiple devices with the
same raid_disk number (an original and a replacement). So removing
a device based on the number won't work. So pass the actual device
handle instead.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When setting the slot number on a device in an active array we
currently check that the number is not already in use.
We then call into the personality's hot_add_disk function
which performs the same test and returns the same error.
Thus the common test is not needed.
As we will shortly be changing some personalities to allow duplicates
in some cases (to support hot-replace), the common test will become
inconvenient.
So remove the common test.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
For each active region corresponding to a bit in the bitmap with have
a 14bit counter (and some flags).
This counts
number of active writes + bit in the on-disk bitmap + delay-needed.
The "delay-needed" is because we always want a delay before clearing a
bit. So the number here is normally number of active writes plus 2.
If there have been no writes for a while, we drop to 1.
If still no writes we clear the bit and drop to 0.
So for consistency, when setting bit from the on-disk bitmap or by
request from user-space it is best to set the counter to '2' to start
with.
In particular we might also set the NEEDED_MASK flag at this time, and
in all other cases NEEDED_MASK is only set when the counter is 2 or
more.
Signed-off-by: NeilBrown <neilb@suse.de>
When an array is being reshaped to change the number of devices,
the two halves can be differently degraded. e.g. one could be
missing a device and the other not.
So we need to be more careful about calculating the 'degraded'
attribute.
Instead of just inc/dec at appropriate times, perform a full
re-calculation examining both possible cases. This doesn't happen
often so it not a big cost, and we already have most of the code to
do it.
Signed-off-by: NeilBrown <neilb@suse.de>
We have a variable 'mddev' in this function, but repeatedly get the
same value by dereferencing bitmap->mddev.
There is room for simplification here...
Signed-off-by: NeilBrown <neilb@suse.de>
The info is already available in /proc/mdstat and /sys/block in
an accessible form so there is no point in putting a road-block in
the ioctl for information gathering.
Signed-off-by: NeilBrown <neilb@suse.de>
commit d0a4bb4927 introduced a
regression which is annoying but fairly harmless.
When writing to an array that is undergoing recovery (a spare
in being integrated into the array), writing to the array will
set bits in the bitmap, but they will not be cleared when the
write completes.
For bits covering areas that have not been recovered yet this is not a
problem as the recovery will clear the bits. However bits set in
already-recovered region will stay set and never be cleared.
This doesn't risk data integrity. The only negatives are:
- next time there is a crash, more resyncing than necessary will
be done.
- the bitmap doesn't look clean, which is confusing.
While an array is recovering we don't want to update the
'events_cleared' setting in the bitmap but we do still want to clear
bits that have very recently been set - providing they were written to
the recovering device.
So split those two needs - which previously both depended on 'success'
and always clear the bit of the write went to all devices.
Signed-off-by: NeilBrown <neilb@suse.de>
Before performing a recovery we try to remove any spares that
might not be working, then add any that might have become relevant.
Currently we abort on the first spare that cannot be added.
This is a false optimisation.
It is conceivable that - depending on rules in the personality - a
subsequent spare might be accepted.
Also the loop does other things like count the available spares and
reset the 'recovery_offset' value.
If we abort early these might not happen properly.
So remove the early abort.
In particular if you have an array what is undergoing recovery and
which has extra spares, then the recovery may not restart after as
reboot as the could of 'spares' might end up as zero.
Reported-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NeilBrown <neilb@suse.de>
While reshaping a degraded array (as when reshaping a RAID0 by first
converting it to a degraded RAID4) we currently get confused about
which devices are in_sync. In most cases we get it right, but in the
region that is being reshaped we need to treat non-failed devices as
in-sync when we have the data but haven't actually written it out yet.
Reported-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
commit d70ed2e4fa
broke hot-add to a linear array.
After that commit, metadata if not written to devices until they
have been fully integrated into the array as determined by
saved_raid_disk. That patch arranged to clear that field after
a recovery completed.
However for linear arrays, there is no recovery - the integration is
instantaneous. So we need to explicitly clear the saved_raid_disk
field.
Signed-off-by: NeilBrown <neilb@suse.de>
Once a device is failed we really want to completely ignore it.
It should go away soon anyway.
In particular the presence of bad blocks on it should not cause us to
block as we won't be trying to write there anyway.
So as soon as we can check if a device is Faulty, do so and pretend
that it is already gone if it is Faulty.
Signed-off-by: NeilBrown <neilb@suse.de>
When we mark blocks as bad we need them to be acknowledged by the
metadata handler promptly.
For an in-kernel metadata handler that was already being done. But
for an external metadata handler we need to alert it of the change by
sending a notification through the sysfs file. This adds that
notification.
Signed-off-by: NeilBrown <neilb@suse.de>
Once a device is marked Faulty the badblocks - whether acknowledged or
not - become irrelevant. So they shouldn't cause the device to be
marked as Blocked.
Without this patch, a process might write "-blocked" to clear the
Blocked status, but while that will correctly fail the device, it
won't remove the apparent 'blocked' status.
Signed-off-by: NeilBrown <neilb@suse.de>
When we are accessing an mddev via sysfs we know that the
mddev cannot disappear because it has an embedded kobj which
is refcounted by sysfs.
And we also take the mddev_lock.
However this is not enough.
The final mddev_put could have been called and the
mddev_delayed_delete is waiting for sysfs to let go so it can destroy
the kobj and mddev.
In this state there are a lot of changes that should not be attempted.
To to guard against this we:
- initialise mddev->all_mddevs in on last put so the state can be
easily detected.
- in md_attr_show and md_attr_store, check ->all_mddevs under
all_mddevs_lock and mddev_get the mddev if it still appears to
be active.
This means that if we get to sysfs as the mddev is being deleted we
will get -EBUSY.
rdev_attr_store and rdev_attr_show are similar but already have
sufficient protection. They check that rdev->mddev still points to
mddev after taking mddev_lock. As this is cleared before delayed
removal which can only be requested under the mddev_lock, this
ensure the rdev and mddev are still alive.
Signed-off-by: NeilBrown <neilb@suse.de>
We like md devices to disappear when they really are not needed.
However it is not possible to tell from the current state whether it
is needed or not. We can only tell from recent history of changes.
In particular immediately after we create an md device it looks very
similar to immediately after we have finished with it.
So we always preserve a newly created md device until something
significant happens. This state is stored in 'hold_active'.
The normal case is to keep it until an ioctl happens, as that will
normally either activate it, or explicitly de-activate it. If it
doesn't then it was probably created by mistake and it is now time to
get rid of it.
We can also modify an array via sysfs (instead of via ioctl) and we
currently treat any change via sysfs like an ioctl as a sign that if
it now isn't more active, it should be destroyed.
However this is not appropriate as changes made via sysfs are more
gradual so we should look for a more definitive change.
So this patch only clears 'hold_active' from UNTIL_IOCTL to clear when
the array_state is changed via sysfs. Other changes via sysfs
are ignored.
Signed-off-by: NeilBrown <neilb@suse.de>
Page attributes are set using __set_bit rather than set_bit as
it normally called under a spinlock so the extra atomicity is not
needed.
However there are two places where we might set or clear page
attributes without holding the spinlock.
So add the spinlock in those cases.
This might be the cause of occasional reports that bits a aren't
getting clear properly - theory is that BITMAP_PAGE_PENDING gets lost
when BITMAP_PAGE_NEEDWRITE is set or cleared. This is an
inconvenience, not a threat to data safety.
Signed-off-by: NeilBrown <neilb@suse.de>
All updates that occur under STRIPE_ACTIVE should be globally visible
when STRIPE_ACTIVE clears. test_and_set_bit() implies a barrier, but
clear_bit() does not.
This is suitable for 3.1-stable.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
When the number of failed devices exceeds the allowed number
we must abort any active parity operations (checks or updates) as they
are no longer meaningful, and can lead to a BUG_ON in
handle_parity_checks6.
This bug was introduce by commit 6c0069c0ae
in 2.6.29.
Reported-by: Manish Katiyar <mkatiyar@gmail.com>
Tested-by: Manish Katiyar <mkatiyar@gmail.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
since it uses the module facilities.
Reported-by: Witold Baryluk <baryluk@smp.if.uj.edu.pl>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For the files which are not themselves modular, we can change
them to include only the smaller export.h since all they are
doing is looking for EXPORT_SYMBOL.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'for-3.2/core' of git://git.kernel.dk/linux-block: (29 commits)
block: don't call blk_drain_queue() if elevator is not up
blk-throttle: use queue_is_locked() instead of lockdep_is_held()
blk-throttle: Take blkcg->lock while traversing blkcg->policy_list
blk-throttle: Free up policy node associated with deleted rule
block: warn if tag is greater than real_max_depth.
block: make gendisk hold a reference to its queue
blk-flush: move the queue kick into
blk-flush: fix invalid BUG_ON in blk_insert_flush
block: Remove the control of complete cpu from bio.
block: fix a typo in the blk-cgroup.h file
block: initialize the bounce pool if high memory may be added later
block: fix request_queue lifetime handling by making blk_queue_cleanup() properly shutdown
block: drop @tsk from attempt_plug_merge() and explain sync rules
block: make get_request[_wait]() fail if queue is dead
block: reorganize throtl_get_tg() and blk_throtl_bio()
block: reorganize queue draining
block: drop unnecessary blk_get/put_queue() in scsi_cmd_ioctl() and blk_get_tg()
block: pass around REQ_* flags instead of broken down booleans during request alloc/free
block: move blk_throtl prototypes to block/blk.h
block: fix genhd refcounting in blkio_policy_parse_and_set()
...
Fix up trivial conflicts due to "mddev_t" -> "struct mddev" conversion
and making the request functions be of type "void" instead of "int" in
- drivers/md/{faulty.c,linear.c,md.c,md.h,multipath.c,raid0.c,raid1.c,raid10.c,raid5.c}
- drivers/staging/zram/zram_drv.c
These files were getting the defines for EXPORT_SYMBOL because
device.h was including module.h. But we are going to put an
end to that. So add the proper export.h include now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
A pending cleanup will mean that module.h won't be implicitly
everywhere anymore. Make sure the modular drivers in md dir
are actually calling out for <module.h> explicitly in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
When devices in a RAID array are not in-sync, they are supposed to be
reported as such in the status output as an 'a' character, which means
"alive, but not in-sync". But when the entire array is rebuilt 'A' is
being used, which is incorrect. This patch corrects this to 'a'.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Allow userspace dm log implementations to register their log device so it
is no longer missing from the list of device dependencies.
When device mapper targets use a device they normally call dm_get_device
which includes it in the device list returned to userspace applications
such as LVM through the DM_TABLE_DEPS ioctl. Userspace log devices
don't use dm_get_device as userspace opens them so they are missing from
the list of dependencies.
This patch extends the DM_ULOG_CTR operation to allow userspace to
respond with the name of the log device (if appropriate) to be
registered via 'dm_get_device'. DM_ULOG_REQUEST_VERSION is incremented.
This is backwards compatible. If the kernel and userspace log server
have both been updated, the new information will be passed down to the
kernel and the device will be registered. If the kernel is new, but
the log server is old, the log server will not pass down any device
information and the kernel will simply bypass the device registration
as before. If the kernel is old but the log server is new, the log
server will see the old version number and not pass the device info.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix comments: clustered-disk needs a hyphen not an underscore.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Initial EXPERIMENTAL implementation of device-mapper thin provisioning
with snapshot support. The 'thin' target is used to create instances of
the virtual devices that are hosted in the 'thin-pool' target. The
thin-pool target provides data sharing among devices. This sharing is
made possible using the persistent-data library in the previous patch.
The main highlight of this implementation, compared to the previous
implementation of snapshots, is that it allows many virtual devices to
be stored on the same data volume, simplifying administration and
allowing sharing of data between volumes (thus reducing disk usage).
Another big feature is support for arbitrary depth of recursive
snapshots (snapshots of snapshots of snapshots ...). The previous
implementation of snapshots did this by chaining together lookup tables,
and so performance was O(depth). This new implementation uses a single
data structure so we don't get this degradation with depth.
For further information and examples of how to use this, please read
Documentation/device-mapper/thin-provisioning.txt
Signed-off-by: Joe Thornber <thornber@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The persistent-data library offers a re-usable framework for the storage
and management of on-disk metadata in device-mapper targets.
It's used by the thin-provisioning target in the next patch and in an
upcoming hierarchical storage target.
For further information, please read
Documentation/device-mapper/persistent-data.txt
Signed-off-by: Joe Thornber <thornber@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The dm-bufio interface allows you to do cached I/O on devices,
holding recently-read blocks in memory and performing delayed writes.
We don't use buffer cache or page cache already present in the kernel, because:
* we need to handle block sizes larger than a page
* we can't allocate memory to perform reads or we'd have deadlocks
Currently, when a cache is required, we limit its size to a fraction of
available memory. Usage can be viewed and changed in
/sys/module/dm_bufio/parameters/ .
The first user is thin provisioning, but more dm users are planned.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Introduce DM_TARGET_IMMUTABLE to indicate that the target type cannot be mixed
with any other target type, and once loaded into a device, it cannot be
replaced with a table containing a different type.
The thin provisioning pool device will use this.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add a target feature flag DM_TARGET_ALWAYS_WRITEABLE to indicate that a target
does not support read-only mode.
The initial implementation of the thin provisioning target uses this.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Introduce the concept of a singleton table which contains exactly one target.
If a target type sets the DM_TARGET_SINGLETON feature bit device-mapper
will ensure that any table that includes that target contains no others.
The thin provisioning pool target uses this.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch introduces dm_kcopyd_zero() to make it easy to use
kcopyd to write zeros into the requested areas instead
instead of copying. It is implemented by passing a NULL
copying source to dm_kcopyd_copy().
The forthcoming thin provisioning target uses this.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Since set_current_state() contains a memory barrier in it,
an additional barrier isn't needed.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
printk_ratelimit() shares global ratelimiting state with all
other subsystems, so its usage is discouraged. Instead,
define and use dm's local state.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Allow QUEUE_FLAG_NONROT to propagate up the device stack if all
underlying devices are non-rotational. Tools like ureadahead will
schedule IOs differently based on the rotational flag.
With this patch, I see boot time go from 7.75 s to 7.46 s on my device.
Suggested-by: J. Richard Barnette <jrbarnette@chromium.org>
Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: dm-devel@redhat.com
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This is a fairly serious bug in RAID10.
When a RAID10 array is degraded and a hot-spare is activated, the
spare does not take up the empty slot, but rather replaces the first
working device.
This is likely to make the array non-functional. It would normally
be possible to recover the data, but that would need care and is not
guaranteed.
This bug was introduced in commit
2bb77736ae
which first appeared in 3.1.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
In 3.0 we changed the way recovery_disabled was handle so that instead
of testing against zero, we test an mddev-> value against a conf->
value.
Two problems:
1/ one place in raid1 was missed and still sets to '1'.
2/ We didn't explicitly set the conf-> value at array creation
time.
It defaulted to '0' just like the mddev value does so they
could appear equal and thus disable recovery.
This did not affect normal 'md' as it calls bind_rdev_to_array
which changes the mddev value. However the dmraid interface
doesn't call this and so doesn't change ->recovery_disabled; so at
array start all recovery is incorrectly disabled.
So initialise the 'conf' value to one less that the mddev value, so
the will only be the same when explicitly set that way.
Reported-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This bug was introduced in 415e72d034
which was in 2.6.36.
There is a small window of time between when a device fails and when
it is removed from the array. During this time we might still read
from it, but we won't write to it - so it is possible that we could
read stale data.
We didn't need the test of 'Faulty' before because the test on
In_sync is sufficient. Since we started allowing reads from the early
part of non-In_sync devices we need a test on Faulty too.
This is suitable for any kernel from 2.6.36 onwards, though the patch
might need a bit of tweaking in 3.0 and earlier.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
bio originally has the functionality to set the complete cpu, but
it is broken.
Chirstoph said that "This code is unused, and from the all the
discussions lately pretty obviously broken. The only thing keeping
it serves is creating more confusion and possibly more bugs."
And Jens replied with "We can kill bio_set_completion_cpu(). I'm fine
with leaving cpu control to the request based drivers, they are the
only ones that can toggle the setting anyway".
So this patch tries to remove all the work of controling complete cpu
from a bio.
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix memory leak introduced by commit a6e50b409d
(dm snapshot: skip reading origin when overwriting complete chunk).
When allocating a set of jobs from kc->job_pool, job->master_job must be
set (to point to itself) so that the mempool item gets freed when the
master_job completes.
master_job was introduced by commit c6ea41fbbe
(dm kcopyd: preallocate sub jobs to avoid deadlock)
Reported-by: Michael Leun <ml@newton.leun.net>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If an incremental recovery was interrupted, a subsequent
re-add will result in a full recovery, even though an
incremental should be possible (seen with raid1).
Solve this problem by not updating the superblock on the
recovering device until array is not degraded any longer.
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrei Warkentin <andreiw@vmware.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When we add a device to an active array it can be meaningful to set
the 'insync' flag. This indicates that the device is in-sync with the
array except for locations recorded in the bitmap.
A bitmap-based recovery can then bring it completely in-sync.
Internally we move that flag to 'saved_raid_disk' but forgot to clear
In_sync like we do in add_new_disk.
So clear In_sync after moving its value to saved_raid_disk.
Reported-by: Andrei Warkentin <andreiw@vmware.com>
Signed-off-by: NeilBrown <neilb@suse.de>
RAID1 and RAID10 handle write requests by queuing them for handling by
a separate thread. This is because when a write-intent-bitmap is
active we might need to update the bitmap first, so it is good to
queue a lot of writes, then do one big bitmap update for them all.
However writeback request devices to appear to be congested after a
while so it can make some guesstimate of throughput. The infinite
queue defeats that (note that RAID5 has already has a finite queue so
it doesn't suffer from this problem).
So impose a limit on the number of pending write requests. By default
it is 1024 which seems to be generally suitable. Make it configurable
via module option just in case someone finds a regression.
Signed-off-by: NeilBrown <neilb@suse.de>
The typedefs are just annoying. 'mdk' probably refers to 'md_k.h'
which used to be an include file that defined this thing.
Signed-off-by: NeilBrown <neilb@suse.de>
When md assembles a RAID0 array it prints out lots of info which
is really just for debugging, so convert that to pr_debug.
It also prints out the resulting configuration which could be
interesting, so keep that as 'printk' but tidy it up a bit.
Signed-off-by: NeilBrown <neilb@suse.de>
When normal-write and sync-read/write bio completes, we should
find out the disk number the bio belongs to. Factor those common
code out to a separate function.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In the 'abort' branch of run(), 'conf' cannot possibly be NULL,
so remove the test.
Reported-by: Zdenek Kabelac <zdenek.kabelac@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
There wasn't much and it is inconsistent.
Also rearrange fields to keep related fields together.
Reported-by: Aapo Laine <aapo.laine@shiftmail.org>
Signed-off-by: NeilBrown <neilb@suse.de>
If optional discard support in dm-crypt is enabled, discards requests
bypass the crypt queue and blocks of the underlying device are discarded.
For the read path, discarded blocks are handled the same as normal
ciphertext blocks, thus decrypted.
So if the underlying device announces discarded regions return zeroes,
dm-crypt must disable this flag because after decryption there is just
random noise instead of zeroes.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix off-by-one error in validation of write_mostly.
The user-supplied value given for the 'write_mostly' argument must be an
index starting at 0. The validation of the supplied argument failed to
check for 'N' ('>' vs '>='), which would have caused an access beyond the
end of the array.
Reported-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Commit a63a5cf (dm: improve block integrity support) introduced a
two-phase initialization of a DM device's integrity profile. This
patch avoids dereferencing a NULL 'template_disk' pointer in
blk_integrity_register() if there is an integrity profile mismatch in
dm_table_set_integrity().
This can occur if the integrity profiles for stacked devices in a DM
table are changed between the call to dm_table_prealloc_integrity() and
dm_table_set_integrity().
Reported-by: Zdenek Kabelac <zkabelac@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: stable@kernel.org # 2.6.39
If no arguments were provided to the corrupt_bio_byte feature an error
should be returned immediately.
Reported-by: Zdenek Kabelac <zkabelac@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The md_notify_reboot() method includes a call to mdelay(1000),
to deal with "exotic SCSI devices" which are too volatile on
reboot. The delay is unconditional. Even if the machine does
not have any block devices, let alone MD devices, the kernel
shutdown sequence is slowed down.
1 second does not matter much with physical hardware, but with
certain virtualization use cases any wasted time in the bootup
& shutdown sequence counts for alot.
* drivers/md/md.c: md_notify_reboot() - only impose a delay if
there was at least one MD device to be stopped during reboot
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The 'allclean' flag is used to cache the fact that there is nothing to
do, so we can avoid waking up and scanning the bitmap regularly.
The two sorts of pages that might need the attention of the bitmap
daemon are BITMAP_PAGE_PENDING and BITMAP_PAGE_NEEDWRITE pages.
So make sure allclean reflects exactly when there are none of those.
So:
set it before scanning all pages with either bit set.
clear it whenever these bits are set
clear it when we desire not to clear one of these bits.
don't clear it any other time.
Signed-off-by: NeilBrown <neilb@suse.de>
The flag 'BITMAP_PAGE_CLEAN' has a confusing name as it doesn't mean
that the page is clean, but rather that there are counters in the page
which allow bits in the bitmap to be cleared - i.e. maybe cleaning can
happen.
So change it to BITMAP_PAGE_PENDING and fix some irregularities:
- Don't set it in bitmap_init_from_disk as bitmap_set_memory_bits
sets it when needed
- in bitmap_daemon_work, if we find a counter that is '1', but
need_sync is set, then set BITMAP_PAGE_PENDING again (it was
recently cleared) to ensure we don't forget about this bit.
Signed-off-by: NeilBrown <neilb@suse.de>
Two related problems:
1/ some error paths call "md_unregister_thread(mddev->thread)"
without subsequently clearing ->thread. A subsequent call
to mddev_unlock will try to wake the thread, and crash.
2/ Most calls to md_wakeup_thread are protected against the thread
disappeared either by:
- holding the ->mutex
- having an active request, so something else must be keeping
the array active.
However mddev_unlock calls md_wakeup_thread after dropping the
mutex and without any certainty of an active request, so the
->thread could theoretically disappear.
So we need a spinlock to provide some protections.
So change md_unregister_thread to take a pointer to the thread
pointer, and ensure that it always does the required locking, and
clears the pointer properly.
Reported-by: "Moshe Melnikov" <moshe@zadarastorage.com>
Signed-off-by: NeilBrown <neilb@suse.de>
cc: stable@kernel.org
There is very little benefit in allowing to let a ->make_request
instance update the bios device and sector and loop around it in
__generic_make_request when we can archive the same through calling
generic_make_request from the driver and letting the loop in
generic_make_request handle it.
Note that various drivers got the return value from ->make_request and
returned non-zero values for errors.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Avoid the hacks need for request based device mappers currently by simply
exporting the symbol instead of trying to get it through the back door.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
0.90 metadata uses an unsigned 32bit number to count the number of
kilobytes used from each device.
This should allow up to 4TB per device.
However we multiply this by 2 (to get sectors) before casting to a
larger type, so sizes above 2TB get truncated.
Also we allow rdev->sectors to be larger than 4TB, so it is possible
for the array to be resized larger than the metadata can handle.
So make sure rdev->sectors never exceeds 4TB when 0.90 metadata is in
used.
Also the sanity check at the end of super_90_load should include level
1 as it used ->size too. (RAID0 and Linear don't use ->size at all).
Reported-by: Pim Zandbergen <P.Zandbergen@macroscoop.nl>
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
A single request to RAID1 or RAID10 might result in multiple
requests if there are known bad blocks that need to be avoided.
To detect if we need to submit another write request we test:
if (sectors_handled < (bio->bi_size >> 9)) {
However this is after we call **_write_done() so the 'bio' no longer
belongs to us - the writes could have completed and the bio freed.
So move the **_write_done call until after the test against
bio->bi_size.
This addresses https://bugzilla.kernel.org/show_bug.cgi?id=41862
Reported-by: Bruno Wolff III <bruno@wolff.to>
Tested-by: Bruno Wolff III <bruno@wolff.to>
Signed-off-by: NeilBrown <neilb@suse.de>
A write can complete at two different places:
1/ when the last member-device write completes, through
raid10_end_write_request
2/ in make_request() when we remove the initial bias from ->remaining.
These two should do exactly the same thing and the comment says they
do, but they don't.
So factor the correct code out into a function and call it in both
places. This makes the code much more similar to RAID1.
The difference is only significant if there is an error, and they
usually take a while, so it is unlikely that there will be an error
already when make_request is completing, so this is unlikely to cause
real problems.
Signed-off-by: NeilBrown <neilb@suse.de>
Waiting for a 'blocked' rdev to become unblocked in the raid5d thread
cannot work with internal metadata as it is the raid5d thread which
will clear the blocked flag.
This wasn't a problem in 3.0 and earlier as we only set the blocked
flag when external metadata was used then.
However we now set it always, so we need to be more careful.
Signed-off-by: NeilBrown <neilb@suse.de>
When the 'blocked' flag on a device is cleared while there are
unacknowledged bad blocks we must fail the device. This is needed for
backwards compatability of the interface.
The code currently uses the wrong test for "unacknowledged bad blocks
exist". Change it to the right test.
Signed-off-by: NeilBrown <neilb@suse.de>
I don't know what I was thinking putting 'rcu' after a dynamically
sized array! The array could still be in use when we call rcu_free()
(That is the point) so we mustn't corrupt it.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Queue idling is used for the anticipation of immediate
sequencial I/O's but md_super_write() is a kind of one-
shot operation, coupled with md_super_wait(), so the
idling in this case will be just a waste of time.
Specifying REQ_NOIDLE prevents it. Instead of adding
the flag to submit_bio() directly, use pre-defined
macro WRITE_FLUSH_FUA.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The 'write-mostly' flag can be changed through sysfs.
With 0.90 metadata, those changes are reflected in the metadata.
For 1.x metadata, they aren't.
So fix super_1_sync to record 'write-mostly' status.
Signed-off-by: NeilBrown <neilb@suse.de>
Sometimes a device will refuse to be set faulty. e.g. RAID1 will
never let the last working device become faulty.
So check if "md_error()" did manage to set the faulty flag and fail
with EBUSY if it didn't.
Resolves-Debian-Bug: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=601198
Reported-by: Mike Hommey <mh+reportbug@glandium.org>
Signed-off-by: NeilBrown <neilb@suse.de>
DM has always advertised both REQ_FLUSH and REQ_FUA flush capabilities
regardless of whether or not a given DM device's underlying devices
also advertised a need for them.
Block's flush-merge changes from 2.6.39 have proven to be more costly
for DM devices. Performance regressions have been reported even when
DM's underlying devices do not advertise that they have a write cache.
Fix the performance regressions by configuring a DM device's flushing
capabilities based on those of the underlying devices' capabilities.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add optional parameter field to dmcrypt table and support
"allow_discards" option.
Discard requests bypass crypt queue processing. Bio is simple remapped
to underlying device.
Note that discard will be never enabled by default because of security
consequences. It is up to the administrator to enable it for encrypted
devices.
(Note that userspace cryptsetup does not understand new optional
parameters yet. Support for this will come later. Until then, you
should use 'dmsetup' to enable and disable this.)
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Support the MD RAID1 personality through dm-raid.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add the ability to parse and use metadata devices to dm-raid. Although
not strictly required, without the metadata devices, many features of
RAID are unavailable. They are used to store a superblock and bitmap.
The role, or position in the array, of each device must be recorded in
its superblock. This is to help with fault handling, array reshaping,
and sanity checks. RAID 4/5/6 devices must be loaded in a specific order:
in this way, the 'array_position' field helps validate the correctness
of the mapping when it is loaded. It can be used during reshaping to
identify which devices are added/removed. Fault handling is impossible
without this field. For example, when a device fails it is recorded in
the superblock. If this is a RAID1 device and the offending device is
removed from the array, there must be a way during subsequent array
assembly to determine that the failed device was the one removed. This
is done by correlating the 'array_position' field and the bit-field
variable 'failed_devices'.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add the write_mostly parameter to RAID1 dm-raid tables.
This allows the user to set the WriteMostly flag on a RAID1 device that
should normally be avoided for read I/O.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Allow the user to specify the region_size.
Ensures that the supplied value meets md's constraints, viz. the number of
regions does not exceed 2^21.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Exactly one of name, uuid or device must be specified when referencing
an existing device. This removes the ambiguity (risking the wrong
device being updated) if two conflicting parameters were specified.
Previously one parameter got used and any others were ignored silently.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move logic to find device based on major/minor number to a separate
function __get_dev_cell (similar to __get_uuid_cell and __get_name_cell).
This makes the function __find_device_hash_cell more straightforward.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move parameter filling from find_device to __find_device_hash_cell.
This patch causes ioctls using __find_device_hash_cell
(DM_DEV_REMOVE_CMD, DM_DEV_SUSPEND_CMD - resume, DM_TABLE_CLEAR_CMD)
to return device parameters, bringing them into line with the other
ioctls.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add corrupt_bio_byte feature to simulate corruption by overwriting a byte at a
specified position with a specified value during intervals when the device is
"down".
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add 'drop_writes' option to drop writes silently while the
device is 'down'. Reads are not touched.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add the ability to specify arbitrary feature flags when creating a
flakey target. This code uses the same target argument helpers that
the multipath target does.
Also remove the superfluous 'dm-flakey' prefixes from the error messages,
as they already contain the prefix 'flakey'.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move multipath target argument parsing code into dm-table so other
targets can share it.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If we write a full chunk in the snapshot, skip reading the origin device
because the whole chunk will be overwritten anyway.
This patch changes the snapshot write logic when a full chunk is written.
In this case:
1. allocate the exception
2. dispatch the bio (but don't report the bio completion to device mapper)
3. write the exception record
4. report bio completed
Callbacks must be done through the kcopyd thread, because callbacks must not
race with each other. So we create two new functions:
dm_kcopyd_prepare_callback: allocate a job structure and prepare the callback.
(This function must not be called from interrupt context.)
dm_kcopyd_do_callback: submit callback.
(This function may be called from interrupt context.)
Performance test (on snapshots with 4k chunk size):
without the patch:
non-direct-io sequential write (dd): 17.7MB/s
direct-io sequential write (dd): 20.9MB/s
non-direct-io random write (mkfs.ext2): 0.44s
with the patch:
non-direct-io sequential write (dd): 26.5MB/s
direct-io sequential write (dd): 33.2MB/s
non-direct-io random write (mkfs.ext2): 0.27s
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add a new flag DMF_MERGE_IS_OPTIONAL to struct mapped_device to indicate
whether the device can accept bios larger than the size its merge
function returns. When set, use this to send large bios to snapshots
which can split them if necessary. Snapshot I/O may be significantly
fragmented and this approach seems to improve peformance.
Before the patch, dm_set_device_limits restricted bio size to page size
if the underlying device had a merge function and the target didn't
provide a merge function. After the patch, dm_set_device_limits
restricts bio size to page size if the underlying device has a merge
function, doesn't have DMF_MERGE_IS_OPTIONAL flag and the target doesn't
provide a merge function.
The snapshot target can't provide a merge function because when the merge
function is called, it is impossible to determine where the bio will be
remapped. Previously this led us to impose a 4k limit, which we can
now remove if the snapshot store is located on a device without a merge
function. Together with another patch for optimizing full chunk writes,
it improves performance from 29MB/s to 40MB/s when writing to the
filesystem on snapshot store.
If the snapshot store is placed on a non-dm device with a merge function
(such as md-raid), device mapper still limits all bios to page size.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
There is no need for __table_get_device to be factored out.
Also move the exports to the end of their respective functions.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Re-order the parameters so they are handled consistently in the same order
where defined, parsed and output.
Only include rebuild parameters in the STATUSTYPE_TABLE output if they were
supplied in the original table line.
Correct the parameter count when outputting rebuild: there are two words,
not one.
Use case-independent checks for keywords (as in other device-mapper targets).
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The nr_pages field in struct kcopyd_job is only used temporarily in
run_pages_job() to count the number of required pages.
We can use a local variable instead.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The offset field in struct kcopyd_job is always zero so remove it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Replace list_del() followed by list_add() with list_move().
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Using __test_and_{set,clear}_bit_le() with ignoring its return value
can be replaced with __{set,clear}_bit_le().
This also removes unnecessary casts.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove 'discards_supported' from the dm_table structure. The same
information can be easily discovered from the table's target(s) in
dm_table_supports_discards().
Before this fix dm_table_supports_discards() would skip checking the
individual targets' 'discards_supported' flag if any one target in the
table didn't set num_discard_requests > 0. Now the per-target
'discards_supported' flag is effective at insuring the final DM device
advertises discard support. But, to be clear, targets that don't
support discards (!num_discard_requests) will not receive discard
requests.
Also DMWARN if a target sets 'discards_supported' override but forgets
to set 'num_discard_requests'.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
For normal kernel pages, CPU cache is synchronized by the dma layer.
However, this is not done for pages allocated with vmalloc. If we do I/O
to/from vmallocated pages, we must synchronize CPU cache explicitly.
Prior to doing I/O on vmallocated page we must call
flush_kernel_vmap_range to flush dirty cache on the virtual address.
After finished read we must call invalidate_kernel_vmap_range to
invalidate cache on the virtual address, so that accesses to the virtual
address return newly read data and not stale data from CPU cache.
This patch fixes metadata corruption on dm-snapshots on PA-RISC and
possibly other architectures with caches indexed by virtual address.
Cc: stable <stable@kernel.org>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Avoid dereferencing a NULL pointer if the number of feature arguments
supplied is fewer than indicated.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: stable@kernel.org
This patch makes dm-snapshot flush disk cache when writing metadata for
merging snapshot.
Without cache flushing the disk may reorder metadata write and other
data writes and there is a possibility of data corruption in case of
power fault.
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
* 'for-linus' of git://neil.brown.name/md: (75 commits)
md/raid10: handle further errors during fix_read_error better.
md/raid10: Handle read errors during recovery better.
md/raid10: simplify read error handling during recovery.
md/raid10: record bad blocks due to write errors during resync/recovery.
md/raid10: attempt to fix read errors during resync/check
md/raid10: Handle write errors by updating badblock log.
md/raid10: clear bad-block record when write succeeds.
md/raid10: avoid writing to known bad blocks on known bad drives.
md/raid10 record bad blocks as needed during recovery.
md/raid10: avoid reading known bad blocks during resync/recovery.
md/raid10 - avoid reading from known bad blocks - part 3
md/raid10: avoid reading from known bad blocks - part 2
md/raid10: avoid reading from known bad blocks - part 1
md/raid10: Split handle_read_error out from raid10d.
md/raid10: simplify/reindent some loops.
md/raid5: Clear bad blocks on successful write.
md/raid5. Don't write to known bad block on doubtful devices.
md/raid5: write errors should be recorded as bad blocks if possible.
md/raid5: use bad-block log to improve handling of uncorrectable read errors.
md/raid5: avoid reading from known bad blocks.
...
Currently when we get a read error during recovery, we simply abort
the recovery.
Instead, repeat the read in page-sized blocks.
On successful reads, write to the target.
On read errors, record a bad block on the destination,
and only if that fails do we abort the recovery.
As we now retry reads we need to know where we read from. This was in
bi_sector but that can be changed during a read attempt.
So store the correct from_addr and to_addr in the r10_bio for later
access.
Signed-off-by: NeilBrown<neilb@suse.de>
If a read error is detected during recovery the code currently
fails the read device.
This isn't really necessary. recovery_request_write will signal
a write error to end_sync_write and it will record a write
error on the destination device which will record a bad block
there or kick it from the array.
So just remove this call to do md_error.
Signed-off-by: NeilBrown <neilb@suse.de>
If we get a write error during resync/recovery don't fail the device
but instead record a bad block. If that fails we can then fail the
device.
Signed-off-by: NeilBrown <neilb@suse.de>
