Commit Graph

351 Commits

Author SHA1 Message Date
Mark Brown
fcdcc79628 Merge branch 'topic/acpi' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into spi-pxa2xx 2016-02-09 18:20:39 +00:00
Geert Uytterhoeven
0697ae80fe spi: Allow compile test of bcm2835aux if !GPIOLIB
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.

Relax the dependency of SPI_BCM2835AUX on GPIOLIB if COMPILE_TEST is
enabled.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2016-02-08 13:42:10 +00:00
Lars-Peter Clausen
b1353d1c1d spi: Add Analog Devices AXI SPI Engine controller support
This patch adds support for the AXI SPI Engine controller which is a FPGA
soft-peripheral which is used in some of Analog Devices' reference designs.

The AXI SPI Engine controller is part of the SPI Engine framework[1] and
allows memory mapped access to the SPI Engine control bus. This allows it
to be used as a general purpose software driven SPI controller. The SPI
Engine in addition offers some optional advanced acceleration and
offloading capabilities, which are not part of this patch though and will
be introduced separately.

At the core of the SPI Engine framework is a small sort of co-processor
that accepts a command stream and turns the commands into low-level SPI
transactions. Communication is done through three memory mapped FIFOs in
the register map of the AXI SPI Engine peripheral. One FIFO for the command
stream and one each for transmit and receive data.

The driver translates a spi_message in a command stream and writes it to
the peripheral which executes it asynchronously. This allows it to perform
very precise timings which are required for some SPI slave devices to
achieve maximum performance (e.g. analog-to-digital and digital-to-analog
converters). The execution flow is synchronized to the host system by a
special synchronize instruction which generates a interrupt.

[1] https://wiki.analog.com/resources/fpga/peripherals/spi_engine

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
2016-02-05 18:12:57 +00:00
Mark Brown
e32bb8709f spi: Fix sorting in Kconfig
Signed-off-by: Mark Brown <broonie@kernel.org>
2016-02-03 10:28:08 +00:00
Jarkko Nikula
22a33632fb spi: pxa2xx: Remove CONFIG_SPI_PXA2XX_DMA
After removal of legacy PXA DMA code by the commit 6356437e65
("spi: spi-pxa2xx: remove legacy PXA DMA bits") the
CONFIG_SPI_PXA2XX_DMA follows the CONFIG_SPI_PXA2XX and cannot be disabled
alone. Therefore remove this config symbol and dead definitions from the
spi-pxa2xx.h.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2016-01-15 18:13:17 +00:00
Mark Brown
cabeea9808 Merge remote-tracking branches 'spi/topic/sun4i', 'spi/topic/topcliff-pch' and 'spi/topic/zynq' into spi-next 2016-01-11 16:48:38 +00:00
Martin Sperl
97896195b3 spi: add spi-loopback-test to build framework
adding the spi-loopback-test module to Kconfig and Makefile

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-12-12 23:05:18 +00:00
Paul Burton
f05ca854b3 spi: topcliff-pch: allow build for MIPS platforms
Allow the topcliff-pch driver to be built for MIPS platforms, in
preparation for use on the MIPS Boston board.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-11-30 16:34:50 +00:00
Mark Brown
fc579056af Merge remote-tracking branches 'spi/topic/fsl-dspi', 'spi/topic/mpc512x', 'spi/topic/mtk', 'spi/topic/oc-tiny' and 'spi/topic/octeon' into spi-next 2015-11-04 11:02:10 +00:00
Mark Brown
c2da04dc21 Merge remote-tracking branches 'spi/topic/bcm53xx', 'spi/topic/bcm63xx', 'spi/topic/bfin-sport', 'spi/topic/bfin5xx' and 'spi/topic/bitbang' into spi-next 2015-11-04 11:02:06 +00:00
Yuan Yao
5a60adafb9 spi: Add DSPI support for layerscape family
LS1043a and LS2080A in the Layerscape family also support DSPI, make
DSPI selectable for these hardwares.

Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-10-30 10:25:53 +09:00
Jonas Gorski
44d8fb3094 spi/bcm63xx: move register definitions into the driver
Move all register definitions and structs into the driver. This allows
us dropping the platform_data struct and drop any arch specific
includes. Make use of different device names to identify the version of
the block we have.

Since we now have full control over the message width, we can drop the
size check, which was broken anyway, since it never set ret to any error
code.

Also since we now have no arch depedendent resources, we can now allow
compiling it for any arch, hidden behind COMPILE_TEST.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-10-23 01:19:58 +09:00
Martin Sperl
1ea29b39f4 spi: bcm2835aux: add bcm2835 auxiliary spi device driver
The bcm2835 has 2 auxiliary spi bus masters spi1 and spi2.

This implements the driver to enable these devices.

The driver does not implement native chip-selects but uses
the aribtrary GPIO-chip-selects provided by the spi-chipselect.

Note that this driver relies on the fact that
the clock is implemented by the clk-bcm2835-aux driver,
which enables/disables the HW block when requesting/releasing
the clock.

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-10-07 11:42:57 +01:00
Mark Brown
c5992f610f Merge remote-tracking branches 'spi/topic/ti-qspi', 'spi/topic/xcomm' and 'spi/topic/xlp' into spi-next 2015-08-31 14:45:45 +01:00
Mark Brown
2ca0a9d80c Merge remote-tracking branches 'spi/topic/mtk', 'spi/topic/pxa2xx', 'spi/topic/qspi', 'spi/topic/rockchip' and 'spi/topic/s3c24xx' into spi-next 2015-08-31 14:45:36 +01:00
Kamlakant Patel
d8c80d49cf spi/xlp: SPI controller driver for Netlogic XLP SoCs
Add SPI Master controller driver for the SPI interface on XLP8XX,
XLP3XX, XLP2XX, XLP9XX and XLP5XX family of Netlogic XLP MIPS64 processors.

Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-08-28 18:22:19 +01:00
Leilk Liu
a568231f46 spi: mediatek: Add spi bus for Mediatek MT8173
This patch adds basic spi bus for MT8173.

Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-08-07 14:35:13 +01:00
Geert Uytterhoeven
2e1c75f4d3 spi: SPI_ZYNQMP_GQSPI should depend on HAS_DMA
If NO_DMA=y:

    ERROR: "dma_unmap_single" [drivers/spi/spi-zynqmp-gqspi.ko] undefined!
    ERROR: "dma_mapping_error" [drivers/spi/spi-zynqmp-gqspi.ko] undefined!
    ERROR: "dma_map_single" [drivers/spi/spi-zynqmp-gqspi.ko] undefined!

Add a dependency on HAS_DMA to fix this.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ranjit Waghmode <ranjitw@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-07-07 13:43:03 +01:00
Mark Brown
fda052b0a5 Merge remote-tracking branches 'spi/topic/sirf', 'spi/topic/spidev' and 'spi/topic/zynq' into spi-next 2015-06-18 00:19:56 +01:00
Mark Brown
b9e2c097ef Merge remote-tracking branches 'spi/topic/pxa', 'spi/topic/rb4xx', 'spi/topic/rspi', 'spi/topic/s3c64xx' and 'spi/topic/sh-msiof' into spi-next 2015-06-18 00:19:53 +01:00
Mark Brown
b6e6dc8034 Merge remote-tracking branches 'spi/topic/fsl-dspi', 'spi/topic/gpio', 'spi/topic/imx' and 'spi/topic/orion' into spi-next 2015-06-18 00:19:51 +01:00
Mark Brown
5d6ada671b Merge remote-tracking branch 'spi/topic/bcm2835' into spi-next 2015-06-18 00:19:48 +01:00
Ranjit Waghmode
dfe11a11d5 spi: Add support for Zynq Ultrascale+ MPSoC GQSPI controller
This patch adds support for GQSPI controller driver used by
Zynq Ultrascale+ MPSoC

Signed-off-by: Ranjit Waghmode <ranjit.waghmode@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-06-12 18:33:39 +01:00
Daniel Mack
6356437e65 spi: spi-pxa2xx: remove legacy PXA DMA bits
Generic DMA support was already implemented by commit cd7bed0034
("spi/pxa2xx: break out the private DMA API usage into a separate file")
which moved all the legacy PXA DMA implementation code into its own
file.

With generic DMA available for PXA, we can now just trash this file.

Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mark Brown <broonie@linaro.org>
[respin after pxa dmaengine support upstream]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-06-09 12:11:29 +01:00
Mark Brown
c8b350424d Merge remote-tracking branches 'spi/fix/fsl-cpm', 'spi/fix/fsl-dspi' and 'spi/fix/fsl-espi' into spi-linus 2015-05-11 17:29:49 +01:00
Geert Uytterhoeven
5c2301a990 spi: Allow compile test of GPIO consumers if !GPIOLIB
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.

Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-05-06 16:20:59 +01:00
Yoshinori Sato
e0d58cdcae spi: bcm2835: depends GPIOLIB
I got following error on CONFIG_GPIOLIB=n.

drivers/spi/spi-bcm2835.c: In function 'chip_match_name':
drivers/spi/spi-bcm2835.c:356:21: error: dereferencing pointer to incomplete type 'struct gpio_chip'
  return !strcmp(chip->label, data);
                     ^
drivers/spi/spi-bcm2835.c: In function 'bcm2835_spi_setup':
drivers/spi/spi-bcm2835.c:382:9: error: implicit declaration of function 'gpiochip_find' [-Werror=implicit-function-declaration]
  chip = gpiochip_find("pinctrl-bcm2835", chip_match_name);
         ^
drivers/spi/spi-bcm2835.c:382:7: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
  chip = gpiochip_find("pinctrl-bcm2835", chip_match_name);
       ^
drivers/spi/spi-bcm2835.c: In function 'chip_match_name':
drivers/spi/spi-bcm2835.c:357:1: warning: control reaches end of non-void function [-Wreturn-type]
 }
 ^

Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-05-04 13:57:36 +01:00
Haikun Wang
50574dd2f6 spi: Kconfig: Add SOC_LS1021A to SPI_FSL_DSPI dependence
LS1021A chip also has the DSPI module.
Add it to the dependence.

Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-04-24 13:25:36 +01:00
Mark Brown
5a1b11cbcc Merge remote-tracking branches 'spi/fix/bcm2835', 'spi/fix/bcm2835-code', 'spi/fix/bitbang', 'spi/fix/fsl-cpm' and 'spi/fix/omap2-mcspi' into spi-linus 2015-04-24 11:10:46 +01:00
Bert Vermeulen
05aec35787 spi: Add SPI driver for Mikrotik RB4xx series boards
This driver mediates access between the connected CPLD and other devices
on the bus.

The m25p80-compatible boot flash and (some models) MMC use regular SPI,
bitbanged as required by the SoC. However the SPI-connected CPLD has
a two-wire mode, in which two bits are transferred per SPI clock
cycle. The second bit is transmitted with the SoC's CS2 pin.

Signed-off-by: Bert Vermeulen <bert@biot.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-04-18 13:57:58 +01:00
Guenter Roeck
8844d0f1cb spi: bcm2835: Add GPIOLIB dependency
Fix:

drivers/spi/spi-bcm2835.c: In function 'chip_match_name':
drivers/spi/spi-bcm2835.c:356:21: error:
			dereferencing pointer to incomplete type
drivers/spi/spi-bcm2835.c: In function 'bcm2835_spi_setup':
drivers/spi/spi-bcm2835.c:382:2: error:
	`		implicit declaration of function 'gpiochip_find'
drivers/spi/spi-bcm2835.c:387:21: error:
			dereferencing pointer to incomplete type

by adding the now mandatory GPIOLIB dependency.

Fixes: a30a555d74 ("spi: bcm2835: transform native-cs to gpio-cs
	on first spi_setup")
Cc: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-04-14 21:08:18 +01:00
Mark Brown
431959c079 Merge remote-tracking branches 'spi/topic/blackfin', 'spi/topic/cadence', 'spi/topic/dw' and 'spi/topic/err' into spi-next 2015-04-11 23:09:09 +01:00
Andy Shevchenko
d744f82683 spi: dw-mid: convert to use dw_dmac instead of intel_mid_dma
intel_mid_dma seems to be unmaintained for a long time. Moreover, the IP block
of DMA itself is the same in both dw_dmac and intel_mid_dma. This patch moves
spi-dw-midpci to use dw_dmac driver.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-03-09 18:11:13 +00:00
Michal Simek
38b6484e5b spi: cadence: Remove Kconfig dependency
Remove Kconfig dependency and enable driver for
all ARCHs.
Also update help description.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-03-09 18:09:30 +00:00
Linus Torvalds
b11a278397 Merge branch 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kconfig updates from Michal Marek:
 "Yann E Morin was supposed to take over kconfig maintainership, but
  this hasn't happened.  So I'm sending a few kconfig patches that I
  collected:

   - Fix for missing va_end in kconfig
   - merge_config.sh displays used if given too few arguments
   - s/boolean/bool/ in Kconfig files for consistency, with the plan to
     only support bool in the future"

* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  kconfig: use va_end to match corresponding va_start
  merge_config.sh: Display usage if given too few arguments
  kconfig: use bool instead of boolean for type definition attributes
2015-02-19 10:36:45 -08:00
Mark Brown
30b9278bf5 Merge remote-tracking branches 'spi/topic/sirf', 'spi/topic/spidev', 'spi/topic/st-ssc' and 'spi/topic/ti-qspi' into spi-next 2015-02-08 11:16:58 +08:00
Mark Brown
4f9f4548a5 Merge remote-tracking branches 'spi/topic/orion', 'spi/topic/pxa2xx', 'spi/topic/qup', 'spi/topic/rockchip' and 'spi/topic/samsung' into spi-next 2015-02-08 11:16:55 +08:00
Mark Brown
d6cd09bea9 Merge remote-tracking branches 'spi/topic/falcon', 'spi/topic/fsf', 'spi/topic/fsl', 'spi/topic/fsl-dspi' and 'spi/topic/gpio' into spi-next 2015-02-08 11:16:46 +08:00
Mark Brown
fab4b42a9a Merge remote-tracking branches 'spi/topic/atmel', 'spi/topic/config', 'spi/topic/dln2' and 'spi/topic/dw' into spi-next 2015-02-08 11:16:43 +08:00
Chao Fu
9298bc7273 spi: spi-fsl-dspi: Remove spi-bitbang
DSPI module need cs change information in
a spi transfer. According to cs change, DSPI
will give last data the right flag. Bitbang
provide cs change behind the last data in
a transfer. So DSPI can not deal the last
data in every transfer properly, so remove
the bitbang in the driver.

Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-01-28 19:25:17 +00:00
Arnd Bergmann
75d30c51f8 spi: pl08x: do not select S3C64XX_PL080
The pl08x driver originally selected S3C64XX_PL080 to avoid having
the legacy Samsung DMA interfaces. Those are now gone, so the
select is no longer needed, but it now causes problems when
CONFIG_DMA_ENGINE is disabled:

arch/arm/plat-samsung/built-in.o: In function `s3c64xx_spi0_set_platdata':
:(.init.text+0x518): undefined reference to `pl08x_filter_id'

This simply removes the 'select' to avoid this problem.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-01-28 17:37:16 +00:00
Michal Simek
78d97a5736 spi: Kconfig: Remove additional newline
Trivial fix.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-01-16 16:30:55 +00:00
Christoph Jaeger
6341e62b21 kconfig: use bool instead of boolean for type definition attributes
Support for keyword 'boolean' will be dropped later on.

No functional change.

Reference: http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.com
Signed-off-by: Christoph Jaeger <cj@linux.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
2015-01-07 13:08:04 +01:00
Esben Haabendal
38455d7ac2 spi: fsl-(e)spi: Support compile as module
Signed-off-by: Esben Haabendal <eha@deif.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-01-06 17:03:34 +00:00
Laurentiu Palcu
3d8c0d749d spi: add support for DLN-2 USB-SPI adapter
This adds support for Diolan DLN2 USB-SPI adapter.

Information about the USB protocol interface can be found in the
Programmer's Reference Manual [1], see section 5.4.6 for the SPI
master module commands and responses.

[1] https://www.diolan.com/downloads/dln-api-manual.pdf

Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2014-12-22 18:36:46 +00:00
Lee Jones
9e862375c5 spi: Add new driver for STMicroelectronics' SPI Controller
This patch adds support for the SPI portion of ST's SSC device.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2014-12-22 18:16:14 +00:00
Mark Brown
f56be67b19 Merge remote-tracking branches 'spi/topic/mxs', 'spi/topic/pxa', 'spi/topic/rockchip', 'spi/topic/samsung' and 'spi/topic/sirf' into spi-next 2014-12-08 12:17:17 +00:00
Mark Brown
dcf695b5f3 Merge remote-tracking branches 'spi/topic/fsl-dspi', 'spi/topic/fsl-espi', 'spi/topic/gpio', 'spi/topic/img-spfi' and 'spi/topic/meson' into spi-next 2014-12-08 12:17:15 +00:00
Beniamino Galvani
1327ecd47f spi: meson: Select REGMAP_MMIO
The Meson SPIFC driver uses regmap mmio functions and so it must
select REGMAP_MMIO to avoid the following build error:

spi-meson-spifc.c: undefined reference to `devm_regmap_init_mmio_clk'

Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2014-11-27 11:00:16 +00:00
Padmavathi Venna
bf77cba95f spi: s3c64xx: add support for exynos7 SPI controller
Exynos7 SPI controller supports only the auto Selection of
CS toggle mode and Exynos7 SoC includes six SPI controllers.
Add support for these changes in Exynos7 SPI controller driver.

Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2014-11-26 19:00:34 +00:00
Beniamino Galvani
c3e4bc5434 spi: meson: Add support for Amlogic Meson SPIFC
This is a driver for the Amlogic Meson SPIFC (SPI flash controller),
which is one of the two SPI controllers available on the SoC. It
doesn't support DMA and has a 64-byte unified transmit/receive buffer.

The device is optimized for interfacing with SPI NOR memories and
allows the execution of standard operations such as read, page
program, sector erase, etc. in a simplified way, toggling a bit in a
dedicated register. The driver doesn't use those predefined commands
and relies only on custom transfers.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2014-11-24 18:54:48 +00:00
Andrew Bresticker
deba25800a spi: Add driver for IMG SPFI controller
Add support for the Synchronous Peripheral Flash Interface (SPFI) master
controller found on IMG SoCs.  The SPFI controller supports 5 chip-select
lines and single/dual/quad mode SPI transfers.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2014-11-17 13:31:08 +00:00
Mark Brown
bab4d751f7 Merge remote-tracking branches 'spi/topic/pl022', 'spi/topic/pxa2xx', 'spi/topic/rspi', 'spi/topic/sh-msiof' and 'spi/topic/sirf' into spi-next 2014-10-03 16:33:42 +01:00
Mark Brown
7020d76971 Merge remote-tracking branches 'spi/topic/davinci', 'spi/topic/doc', 'spi/topic/dw' and 'spi/topic/fsl' into spi-next 2014-10-03 16:33:39 +01:00
Mark Brown
1fc8450313 Merge remote-tracking branches 'spi/topic/bcm53xx', 'spi/topic/cadence', 'spi/topic/checkpatch' and 'spi/topic/clps711x' into spi-next 2014-10-03 16:33:37 +01:00
Axel Lin
933fc7b06c spi: bcm53xx: Fix module dependency
config SPI_BCM53XX needs to depend on BCMA_POSSIBLE and select BCMA.
This fixes below build error:
ERROR: "bcma_driver_unregister" [drivers/spi/spi-bcm53xx.ko] undefined!
ERROR: "__bcma_driver_register" [drivers/spi/spi-bcm53xx.ko] undefined!

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2014-09-26 09:08:09 +01:00
Andy Shevchenko
ea092455d7 spi: dw-mid: remove Moorestown support
The support of the Moorestown was removed [1] from kernel long time ago. This
is just a follow up of that change.

[1] http://www.spinics.net/lists/platform-driver-x86/msg02948.html

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2014-09-13 17:01:57 +01:00
Geert Uytterhoeven
f59838a07a spi/drivers: Restrict COMPILE_TEST by HAS_DMA where needed
commit dd1053a93f ("spi/drivers: Enable build of drivers with
COMPILE_TEST") allows compile-testing drivers on platforms they're not
meant for.

However, adding "|| COMPILE_TEST" bypasses all other implicit dependencies
assumed by the platform dependencies before, like HAS_DMA.

If NO_DMA=y:

drivers/built-in.o: In function `atmel_spi_dma_unmap_xfer':
drivers/spi/spi-atmel.c:915: undefined reference to `dma_unmap_single'
drivers/spi/spi-atmel.c:918: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `atmel_spi_next_xfer_data':
drivers/spi/spi-atmel.c:690: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `atmel_spi_dma_map_xfer':
drivers/spi/spi-atmel.c:890: undefined reference to `dma_map_single'
drivers/spi/spi-atmel.c:893: undefined reference to `dma_mapping_error'
drivers/spi/spi-atmel.c:897: undefined reference to `dma_map_single'
drivers/spi/spi-atmel.c:900: undefined reference to `dma_mapping_error'
drivers/spi/spi-atmel.c:902: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `atmel_spi_probe':
drivers/spi/spi-atmel.c:1540: undefined reference to `dma_alloc_coherent'
drivers/spi/spi-atmel.c:1623: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `atmel_spi_remove':
drivers/spi/spi-atmel.c:1665: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `ep93xx_spi_dma_finish':
drivers/spi/spi-ep93xx.c:550: undefined reference to `dma_unmap_sg'
drivers/built-in.o: In function `ep93xx_spi_dma_prepare':
drivers/spi/spi-ep93xx.c:516: undefined reference to `dma_map_sg'
drivers/spi/spi-ep93xx.c:522: undefined reference to `dma_unmap_sg'
drivers/built-in.o: In function `omap2_mcspi_rx_dma':
drivers/spi/spi-omap2-mcspi.c:475: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `omap2_mcspi_txrx_dma':
drivers/spi/spi-omap2-mcspi.c:589: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `omap2_mcspi_transfer_one_message':
drivers/spi/spi-omap2-mcspi.c:1202: undefined reference to `dma_map_single'
drivers/spi/spi-omap2-mcspi.c:1204: undefined reference to `dma_mapping_error'
drivers/spi/spi-omap2-mcspi.c:1211: undefined reference to `dma_map_single'
drivers/spi/spi-omap2-mcspi.c:1213: undefined reference to `dma_mapping_error'
drivers/spi/spi-omap2-mcspi.c:1217: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `tegra_spi_deinit_dma_param':
drivers/spi/spi-tegra114.c:675: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `tegra_spi_copy_spi_rxbuf_to_client_rxbuf':
drivers/spi/spi-tegra114.c:415: undefined reference to `dma_sync_single_for_cpu'
drivers/spi/spi-tegra114.c:440: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `tegra_spi_copy_client_txbuf_to_spi_txbuf':
drivers/spi/spi-tegra114.c:381: undefined reference to `dma_sync_single_for_cpu'
drivers/spi/spi-tegra114.c:405: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `tegra_spi_start_dma_based_transfer':
drivers/spi/spi-tegra114.c:543: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `tegra_slink_deinit_dma_param':
drivers/spi/spi-tegra20-slink.c:705: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `tegra_slink_copy_spi_rxbuf_to_client_rxbuf':
drivers/spi/spi-tegra20-slink.c:427: undefined reference to `dma_sync_single_for_cpu'
drivers/spi/spi-tegra20-slink.c:452: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `tegra_slink_copy_client_txbuf_to_spi_txbuf':
drivers/spi/spi-tegra20-slink.c:393: undefined reference to `dma_sync_single_for_cpu'
drivers/spi/spi-tegra20-slink.c:417: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `tegra_slink_start_dma_based_transfer':
drivers/spi/spi-tegra20-slink.c:561: undefined reference to `dma_sync_single_for_cpu'

Add dependencies on HAS_DMA to fix this.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2014-08-31 13:59:48 +01:00
Rafał Miłecki
0fc6a323e1 spi: bcm53xx: driver for SPI controller on Broadcom bcma SoC
Broadcom 53xx ARM SoCs use bcma bus that contains various cores (AKA
devices). If board has a serial flash, it's connected over SPI and the
bcma bus includes a SPI controller. Example log from such a board:
bus0: Found chip with id 53010, rev 0x00 and package 0x02
(...)
bus0: Core 18 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0)

This patch adds a bcma driver for SPI core, it registers SPI master
controller and "bcm53xxspiflash" SPI device.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-08-19 11:30:55 -05:00
Chew, Chiau Ee
afa93c9017 spi/pxa2xx-pci: Add common clock framework support in PCI glue layer
SPI PXA2XX core layer has dependency on common clock framework
to obtain information on host supported clock rate. Thus, we
setup the clock device in the PCI glue layer to enable PCI mode
host pass in the clock rate information.

Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Acked-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-08-16 17:19:50 -05:00
Mark Brown
fab6a0410d Merge remote-tracking branches 'spi/topic/sh', 'spi/topic/sh-msiof' and 'spi/topic/topcliff-pch' into spi-next 2014-08-04 17:21:16 +01:00
Mark Brown
0c18b7638a Merge remote-tracking branches 'spi/topic/orion', 'spi/topic/pl022', 'spi/topic/qup', 'spi/topic/rockchip' and 'spi/topic/rspi' into spi-next 2014-08-04 17:21:12 +01:00
Geert Uytterhoeven
533465a8f8 spi: rspi: Relax DMA dependency and increase build coverage
As of commit ab116a4df4 ("dmaengine:
shdma: fix a build failure on platforms with no DMA support"), the DMA
filter function shdma_chan_filter() is sufficiently abstracted to allow
building without DMA support. Hence drop the SH_DMAE_BASE dependency on
SUPERH.
Also increase build coverage by allowing the driver to be enabled if
COMPILE_TEST=y.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-10 12:36:11 +02:00
Geert Uytterhoeven
51fd509046 spi: sh-msiof: SPI_SH_MSIOF should depend on HAS_DMA
If NO_DMA=y:

    drivers/built-in.o: In function `sh_msiof_release_dma':
    spi-sh-msiof.c:(.text+0x23cbfe): undefined reference to `dma_unmap_single'
    drivers/built-in.o: In function `sh_msiof_request_dma':
    spi-sh-msiof.c:(.text+0x23cd5e): undefined reference to `dma_map_single'
    spi-sh-msiof.c:(.text+0x23cd70): undefined reference to `dma_mapping_error'
    spi-sh-msiof.c:(.text+0x23cdca): undefined reference to `dma_unmap_single'
    drivers/built-in.o: In function `sh_msiof_dma_once':
    spi-sh-msiof.c:(.text+0x23d450): undefined reference to `dma_sync_single_for_cpu'
    spi-sh-msiof.c:(.text+0x23d5ea): undefined reference to `dma_sync_single_for_cpu'

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-10 12:33:55 +02:00
Mark Brown
c15369087a spi/rockchip: Add dependencies on relaxed I/O accessors
Without the dependencies for the accessors the driver can be enabled on
architectures where it will fail to build.

Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-05 12:51:52 +01:00
addy ke
64e36824b3 spi/rockchip: add driver for Rockchip RK3xxx SoCs integrated SPI
In order to facilitate understanding, rockchip SPI controller IP design
looks similar in its registers to designware. But IC implementation
is different from designware, So we need a dedicated driver for Rockchip
RK3XXX SoCs integrated SPI. The main differences:

- dma request line: rockchip SPI controller have two DMA request line
  for tx and rx.

- Register offset:
                  RK3288        dw
  SPI_CTRLR0      0x0000        0x0000
  SPI_CTRLR1      0x0004        0x0004
  SPI_SSIENR      0x0008        0x0008
  SPI_MWCR        NONE          0x000c
  SPI_SER         0x000c        0x0010
  SPI_BAUDR       0x0010        0x0014
  SPI_TXFTLR      0x0014        0x0018
  SPI_RXFTLR      0x0018        0x001c
  SPI_TXFLR       0x001c        0x0020
  SPI_RXFLR       0x0020        0x0024
  SPI_SR          0x0024        0x0028
  SPI_IPR         0x0028        NONE
  SPI_IMR         0x002c        0x002c
  SPI_ISR         0x0030        0x0030
  SPI_RISR        0x0034        0x0034
  SPI_TXOICR      NONE          0x0038
  SPI_RXOICR      NONE          0x003c
  SPI_RXUICR      NONE          0x0040
  SPI_MSTICR      NONE          0x0044
  SPI_ICR         0x0038        0x0048
  SPI_DMACR       0x003c        0x004c
  SPI_DMATDLR     0x0040        0x0050
  SPI_DMARDLR     0x0044        0x0054
  SPI_TXDR        0x0400        NONE
  SPI_RXDR        0x0800        NONE
  SPI_IDR         NONE          0x0058
  SPI_VERSION     NONE          0x005c
  SPI_DR          NONE          0x0060

- register configuration:
  such as SPI_CTRLRO in rockchip SPI controller:
    cr0 = (CR0_BHT_8BIT << CR0_BHT_OFFSET)
        | (CR0_SSD_ONE << CR0_SSD_OFFSET);
    cr0 |= (rs->n_bytes << CR0_DFS_OFFSET);
    cr0 |= ((rs->mode & 0x3) << CR0_SCPH_OFFSET);
    cr0 |= (rs->tmode << CR0_XFM_OFFSET);
    cr0 |= (rs->type << CR0_FRF_OFFSET);
  For more information, see RK3288 chip manual.

- Wait for idle: Must ensure that the FIFO data has been sent out
  before the next transfer.

Signed-off-by: addy ke <addy.ke@rock-chips.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-04 19:32:29 +01:00
Mark Brown
446fe5e2d5 Merge remote-tracking branches 'spi/topic/adi', 'spi/topic/atmel' and 'spi/topic/cadence' into spi-next 2014-06-02 17:08:35 +01:00
Jean Delvare
2b16069a7a spi/topcliff-pch: Fix Kconfig dependencies
The spi-topcliff-pch driver is for a companion chip to the Intel Atom
E600 series processors. These are 32-bit x86 processors so the driver
is only needed on X86_32. Add COMPILE_TEST as an alternative, so that
the driver can still be build-tested elsewhere.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-05-16 20:07:53 +01:00
Harini Katakam
25dbe04a24 spi: cadence: Add dependency on ARM
Add dependency on ARM in Kconfig.
This is to fix the build error related to _relaxed IO.
Remove dependency on SPI_MASTER because this is already defined
under if SPI_MASTER in Kconfig.

Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-04-15 12:17:07 +01:00
Harini Katakam
c474b38665 spi: Add driver for Cadence SPI controller
Add driver for Cadence SPI controller. This is used in Xilinx Zynq.

Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-04-14 21:00:28 +01:00
Scott Jiang
766e372199 spi: convert spi-bfin-v3.c to a multiplatform driver
Spi v3 controller is not only used on Blackfin. So rename it
and use ioread/iowrite api to make it work on other platform.

Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-04-14 17:45:25 +01:00
Paul Bolle
058f11c851 spi: qup: Depend on ARCH_QCOM
Commit 8fc1b0f87d ("ARM: qcom: Split Qualcomm support into legacy and
multiplatform") removed Kconfig symbol ARCH_MSM_DT. But that commit
left one (optional) dependency on ARCH_MSM_DT untouched.

Three Kconfig symbols used to depend on ARCH_MSM_DT: ARCH_MSM8X60,
ARCH_MSM8960, and ARCH_MSM8974. These three symbols now depend on
ARCH_QCOM. So it appears this driver needs to depend on ARCH_QCOM too.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-04-08 12:09:37 +01:00
Mark Brown
45b15d98a9 Merge remote-tracking branches 'spi/topic/xilinx' and 'spi/topic/xtfpga' into spi-next 2014-03-30 00:51:48 +00:00
Mark Brown
b1ad487c42 Merge remote-tracking branches 'spi/topic/sunxi', 'spi/topic/tegra114', 'spi/topic/ti-qspi', 'spi/topic/ti-ssp', 'spi/topic/topcliff-pch', 'spi/topic/txx9', 'spi/topic/xcomm' and 'spi/topic/xfer' into spi-next 2014-03-30 00:51:41 +00:00
Mark Brown
81235b4ea3 Merge remote-tracking branches 'spi/topic/s3c64xx', 'spi/topic/sc18is602', 'spi/topic/sh-hspi', 'spi/topic/sh-msiof', 'spi/topic/sh-sci', 'spi/topic/sirf' and 'spi/topic/spidev' into spi-next 2014-03-30 00:51:34 +00:00
Mark Brown
1752368064 Merge remote-tracking branches 'spi/topic/omap-uwire', 'spi/topic/omap100k', 'spi/topic/omap2', 'spi/topic/orion', 'spi/topic/pl022', 'spi/topic/qup', 'spi/topic/rspi' and 'spi/topic/s3c24xx' into spi-next 2014-03-30 00:51:27 +00:00
Mark Brown
6e07b9179a Merge remote-tracking branches 'spi/topic/imx', 'spi/topic/init', 'spi/topic/mpc512x-psc', 'spi/topic/mpc52xx', 'spi/topic/mxs', 'spi/topic/nuc900', 'spi/topic/oc-tiny' and 'spi/topic/octeon' into spi-next 2014-03-30 00:51:17 +00:00
Mark Brown
3bcbc14911 Merge remote-tracking branches 'spi/topic/drivers', 'spi/topic/dw', 'spi/topic/efm32', 'spi/topic/ep93xx', 'spi/topic/fsl', 'spi/topic/fsl-dspi', 'spi/topic/fsl-espi' and 'spi/topic/gpio' into spi-next 2014-03-30 00:51:10 +00:00
Mark Brown
9dee279b40 Merge remote-tracking branches 'spi/topic/bus-num', 'spi/topic/cleanup', 'spi/topic/clps711x', 'spi/topic/coldfire', 'spi/topic/completion' and 'spi/topic/davinci' into spi-next 2014-03-30 00:51:03 +00:00
Axel Lin
5634dd8bf4 spi: clps711x: Enable driver compilation with COMPILE_TEST
This helps increasing build testing coverage.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-27 13:29:19 +00:00
Axel Lin
be8dde4675 spi: xtensa-xtfpga: Enable driver compilation with COMPILE_TEST
This helps increasing build testing coverage.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-21 18:11:23 +00:00
Arnd Bergmann
7661ba5a84 spi: remove obsolete spi-ti-ssp driver
The tnetv107x platform is getting removed, so this driver
will not be needed any more.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-18 17:27:24 +00:00
Max Filippov
6840cc29f2 spi: add xtfpga SPI controller driver
This simple SPI master controller is built into xtfpga bitstreams. It
always transfers 16 bit words in SPI mode 0, automatically asserting CS
on transfer start and deasserting on end.

Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-03-13 09:12:44 +00:00
Geert Uytterhoeven
1bd6363bc0 spi: sh-msiof: Use core message handling instead of spi-bitbang
The only remaining feature of spi-bitbang used by this driver is the
chipselect() callback, which just does conditional GPIO.
This is handled fine by the SPI core's spi_set_cs(), hence switch the
driver to use the core message handling through our own transfer_one()
method.

As the (optional) GPIO CS is no longer deasserted at spi_master.setup()
time (through spi_bitbang_setup() and the spi_bitbang.chipselect()
callback), we now have to take care of that ourselves.

Remove the call to spi_master_put() in sh_msiof_spi_remove(), as our SPI
master is now registered using devm_spi_register_master()
(spi_bitbang_start() uses the non-managed version).

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-27 19:44:04 +09:00
Axel Lin
80faf90f97 spi: qup: Depend on ARM && COMPILE_TEST to avoid build error
This driver uses writel_relaxed() which does not exist in x86, ppc, etc.
Make it depend on ARM && COMPILE_TEST to avoid below build error:

  CC [M]  drivers/spi/spi-qup.o
drivers/spi/spi-qup.c: In function 'spi_qup_set_state':
drivers/spi/spi-qup.c:180:3: error: implicit declaration of function 'writel_relaxed' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[2]: *** [drivers/spi/spi-qup.o] Error 1
make[1]: *** [drivers/spi] Error 2
make: *** [drivers] Error 2

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-24 14:44:57 +09:00
Axel Lin
702d3cf9d0 spi: qup: Enable driver compilation with COMPILE_TEST
This helps increasing build testing coverage.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-23 14:39:06 +09:00
Maxime Ripard
b5f6517948 spi: sunxi: Add Allwinner A10 SPI controller driver
The older Allwinner SoCs (A10, A13, A10s and A20) all have the same SPI
controller.

Unfortunately, this SPI controller, even though quite similar, is significantly
different from the recently supported A31 SPI controller (different registers
offset, split/merged registers, etc.). Supporting both controllers in a single
driver would be unreasonable, hence the addition of a new driver.

Like its more recent counterpart, it supports DMA, but the driver only does PIO
until we have a dmaengine driver for this platform.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-23 11:14:46 +09:00
Fabio Estevam
d00694167b spi/imx: Drop default setting for SPI_IMX
SPI_IMX is selected by imx_v6_v7_defconfig/imx_v4_v5_defconfig and we don't need
to have a default setting which depends on the IMX_HAVE_PLATFORM_SPI_IMX symbol.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-23 10:32:33 +09:00
Ivan T. Ivanov
64ff247a97 spi: Add Qualcomm QUP SPI controller support
Qualcomm Universal Peripheral (QUP) core is an AHB slave that
provides a common data path (an output FIFO and an input FIFO)
for serial peripheral interface (SPI) mini-core. SPI in master
mode supports up to 50MHz, up to four chip selects, programmable
data path from 4 bits to 32 bits and numerous protocol variants.

Cc: Alok Chauhan <alokc@codeaurora.org>
Cc: Gilad Avidov <gavidov@codeaurora.org>
Cc: Kiran Gunda <kgunda@codeaurora.org>
Cc: Sagar Dharia <sdharia@codeaurora.org>
Cc: dsneddon@codeaurora.org
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-20 00:29:06 +09:00
Chao Fu
1acbdeb92c spi/fsl-dspi: Convert to use regmap and add big-endian support
Freescale DSPI module will have two endianess in different platform,
but ARM is little endian. So when DSPI in big endian, core in little endian,
readl and writel can not adjust R/W register in this condition.
This patch will remove general readl/writel, and import regmap mechanism.
Data endian will be transfered in regmap APIs.

Documents: dspi add bool "big-endian" in dts node if DSPI module
work in big endian.

Signed-off-by: Chao Fu <b44548@freescale.com>
Reviewed-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-16 09:15:23 +08:00
Paul Bolle
f6ab395bfe spi: omap2: use SUPERH, not SH
Commit 0079aae0f1 ("spi: omap2: Add build dependencies for
writel_relaxed()") added an optional Kconfig dependency on SH. That
Kconfig symbol doesn't exist. Apparently SUPERH was intended. Use that.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-10 12:34:32 +00:00
Mark Brown
7961656a6f spi/sunxi: Add missing dependency on RESET_CONTROLLER
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-06 19:55:03 +00:00
Maxime Ripard
3558fe900e spi: sunxi: Add Allwinner A31 SPI controller driver
The Allwinner A31 has a new SPI controller IP compared to the older Allwinner
SoCs.

It supports DMA, but the driver only does PIO for now, and DMA will be
supported eventually.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-05 14:58:36 +00:00
Geert Uytterhoeven
e290c3434b spi: rspi: Document support for Renesas QSPI in Kconfig
As of commit 5ce0ba8865 ("spi: rcar: add
Renesas QSPI support on RSPI") the rspi driver handles Renesas QSPI, too,
but this was not reflected in the Kconfig help text.

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-04 19:22:30 +00:00
Baruch Siach
794f61a30e spi: dw-mmio: remove HAVE_CLK build dependecy
Since 93abe8e4 (clk: add non CONFIG_HAVE_CLK routines) code using clk.h
like this platform driver needs not depend on HAVE_CLK.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
2014-02-03 12:19:59 +00:00
Linus Torvalds
2d2e7d195b spi: Updates for v3.14
A respun version of the merges for the pull request previously sent with
 a few additional fixes.  The last two merges were fixed up by hand since
 the branches have moved on and currently have the prior merge in them.
 
 Quite a busy release for the SPI subsystem, mostly in cleanups big and
 small scattered through the stack rather than anything else:
 
  - New driver for the Broadcom BC63xx HSSPI controller.
  - Fix duplicate device registration for ACPI.
  - Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA
    changes upon which the transiton depends).
  - Some small optimisations to reduce the amount of time we hold locks
    in the datapath, eliminate some redundant checks and the size of a
    spi_transfer.
  - Lots of fixes, cleanups and general enhancements to drivers,
    especially the rspi and Atmel drivers.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJS4RZvAAoJELSic+t+oim9XKAP/00WcCARVzqWmzZYhW2nCqVw
 zRu/DEC+RFlvUSOrwx5SojZNCJekKrsbJuzvapXKIj+SL5+wDm2gUo188s+J8e5V
 mXA9CGb2+tQUgzuQzKZ82kf5WT1a/VpgdVqxZ2EGBHqdJwMV6cG20YneTd9/A0ar
 QbD9Ikon07cE6j8sp/HKxzSnER+3ii4OTJPJCXkNPHiDE9xkA/FR4qy/DksC2hpy
 y6IHCNGA3yHB/8bC7hxUKabOBwPpvQlGELTLHKTVy4umoAE0/aYSjwMdE67SbqXg
 mxDLcDjacNb4ga9hfWiYdZOKRdYiljt1zXksKHldp+R654YFTSVGmYipMoc0l52b
 jyycLM9ZjQ8Q74ySY+BIdZ4RDKFg4QajDhd/sIJtI354HLdoJCQa82j3luj6/Ewu
 JSlI4EGZUjOWPZb72kkrwj0LFBT5k639fMmLPDCLLlg5sUvx2afFl96s9Z25mFGj
 JzgwhjBIcF8AmllLTEpS6cP8MOBeThJ79gTxmbH60tsWxil2yCS4etg+h6GFo7g9
 GBXL9UF63Q6t9Mg8/0oACDs/YyMMbFImi6p20B+Pr0QZiltiTSSc4Z7eo4gG4UYh
 m4svqZcMG8w6csMAMb6I6a9+EojERPt53bZayasnnX/e5HsXJah4qop9Pjrma4ed
 PQHMx8ivWztwyqqjoYTz
 =CbUw
 -----END PGP SIGNATURE-----

Merge tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "A respun version of the merges for the pull request previously sent
  with a few additional fixes.  The last two merges were fixed up by
  hand since the branches have moved on and currently have the prior
  merge in them.

  Quite a busy release for the SPI subsystem, mostly in cleanups big and
  small scattered through the stack rather than anything else:

   - New driver for the Broadcom BC63xx HSSPI controller
   - Fix duplicate device registration for ACPI
   - Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA
     changes upon which the transiton depends)
   - Some small optimisations to reduce the amount of time we hold locks
     in the datapath, eliminate some redundant checks and the size of a
     spi_transfer
   - Lots of fixes, cleanups and general enhancements to drivers,
     especially the rspi and Atmel drivers"

* tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (112 commits)
  spi: core: Fix transfer failure when master->transfer_one returns positive value
  spi: Correct set_cs() documentation
  spi: Clarify transfer_one() w.r.t. spi_finalize_current_transfer()
  spi: Spelling s/finised/finished/
  spi: sc18is602: Convert to use bits_per_word_mask
  spi: Remove duplicate code to set default bits_per_word setting
  spi/pxa2xx: fix compilation warning when !CONFIG_PM_SLEEP
  spi: clps711x: Add MODULE_ALIAS to support module auto-loading
  spi: rspi: Add missing clk_disable() calls in error and cleanup paths
  spi: rspi: Spelling s/transmition/transmission/
  spi: rspi: Add support for specifying CPHA/CPOL
  spi/pxa2xx: initialize DMA channels to -1 to prevent inadvertent match
  spi: rspi: Add more QSPI register documentation
  spi: rspi: Add more RSPI register documentation
  spi: rspi: Remove dependency on DMAE for SHMOBILE
  spi/s3c64xx: Correct indentation
  spi: sh: Use spi_sh_clear_bit() instead of open-coded
  spi: bitbang: Grammar s/make to make/to make/
  spi: sh-hspi: Spelling s/recive/receive/
  spi: core: Improve tx/rx_nbits check comments
  ...
2014-01-25 13:20:36 -08:00
Linus Torvalds
f2c73464d7 ARM: SoC cleanups for 3.14
This is the branch where we usually queue up cleanup efforts, moving
 drivers out of the architecture directory, header file restructuring,
 etc. Sometimes they tangle with new development so it's hard to keep it
 strictly to cleanups.
 
 Some of the things included in this branch are:
 
 * Atmel SAMA5 conversion to common clock
 * Reset framework conversion for tegra platforms
  - Some of this depends on tegra clock driver reworks that are shared with Mike
    Turquette's clk tree.
 * Tegra DMA refactoring, which are shared branches with the DMA tree.
 * Removal of some header files on exynos to prepare for multiplatform
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJS4Vf7AAoJEIwa5zzehBx3f9UP/jwMlbfbSZHfNQ/QG0SqZ9RD
 zvddyDMHY/qXnzgF3Dax+JR9BDDVy8AlQe713FCoiHJZggWRAbbavkx8gxITDrZQ
 6NYaEkkuVxqyM8APl3PwMqYm8UZ8MUf4lCltlOA4jkesY9vue91AFnfyKh2CvHrn
 Leg4XT6mFzf/vYDL6RbvTz/Qr253uv3KvYBxkeiRNa0Y7OXRemEXSOfgxh0YGxUl
 LZ2IWQFOh/DH4kaeQI8V4G67X3ceHiFyhCnl0CPwfxaZaNBVaxvIFgIUTdetS6Sb
 zcXa029tE/Dfsr55vZAv9LUHEipCSOeE5rn2EJWehTWyM7vJ42Eozqgh+zfCjXS7
 Ib6g2npsvIluQit/RdITu44h5yZlrQsLgKTGJ8jjXqbT4HQ/746W8b/TP0YLtbw7
 N8oqr7k4vsZyF0dAYZQtfQUZeGISz67UbFcdzl9tmYOR7HFuAYkAQYst77zkVJf8
 om59BAYYTG5FNjQ4I9AKUfJzxXYveI6AKpXSCCZiahpFM2D1CJIzp9Wi0GwK1HRR
 sFVWhS0dajvz63pVVC2tw5Sq4J7onRRNGIXFPoE5fkmlelm0/q0zzGjw3Z0nTqbZ
 8zxuwuy2FfPJK11GbUAIhAgn1sCLYyAhl6IE+FsanGeMOSGIMrH0v5/HphAxoCXt
 BvqMDogyLoGPce1Gm3pJ
 =3CcT
 -----END PGP SIGNATURE-----

Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC cleanups from Olof Johansson:
 "This is the branch where we usually queue up cleanup efforts, moving
  drivers out of the architecture directory, header file restructuring,
  etc.  Sometimes they tangle with new development so it's hard to keep
  it strictly to cleanups.

  Some of the things included in this branch are:

   * Atmel SAMA5 conversion to common clock
   * Reset framework conversion for tegra platforms
    - Some of this depends on tegra clock driver reworks that are shared
      with Mike Turquette's clk tree.
   * Tegra DMA refactoring, which are shared branches with the DMA tree.
   * Removal of some header files on exynos to prepare for
     multiplatform"

* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
  ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
  ARM: mvebu: remove prototypes of non-existing functions from common.h
  ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
  serial: sh-sci: Rework baud rate calculation
  serial: sh-sci: Compute overrun_bit without using baud rate algo
  serial: sh-sci: Remove unused GPIO request code
  serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
  serial: sh-sci: Support resources passed through platform resources
  serial: sh-sci: Don't check IRQ in verify port operation
  serial: sh-sci: Set the UPF_FIXED_PORT flag
  serial: sh-sci: Remove duplicate interrupt check in verify port op
  serial: sh-sci: Simplify baud rate calculation algorithms
  serial: sh-sci: Remove baud rate calculation algorithm 5
  serial: sh-sci: Sort headers alphabetically
  ARM: EXYNOS: Kill exynos_pm_late_initcall()
  ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
  ARM: at91: switch Calao QIL-A9260 board to DT
  clk: at91: fix pmc_clk_ids data type attriubte
  PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
  ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
  ...
2014-01-23 18:36:55 -08:00
Mark Brown
8aeab58e56 Merge remote-tracking branches 'spi/topic/pxa2xx', 'spi/topic/qspi', 'spi/topic/s3c24xx', 'spi/topic/s3c64xx', 'spi/topic/sh', 'spi/topic/tegra114', 'spi/topic/tegra20-sflash', 'spi/topic/tegra20-slink', 'spi/topic/txx9' and 'spi/topic/xcomm' into spi-linus 2014-01-23 13:07:14 +00:00
Mark Brown
907e26b6f5 Merge remote-tracking branches 'spi/topic/fsl-espi', 'spi/topic/gpio', 'spi/topic/hspi', 'spi/topic/mpc512x', 'spi/topic/msiof', 'spi/topic/nuc900', 'spi/topic/oc-tiny', 'spi/topic/omap', 'spi/topic/orion' and 'spi/topic/pci' into spi-linus 2014-01-23 13:07:09 +00:00
Mark Brown
36e66bf84f Merge remote-tracking branches 'spi/topic/bcm2835', 'spi/topic/bcm63xx', 'spi/topic/bcm63xx-hsspi', 'spi/topic/bitbang', 'spi/topic/bpw', 'spi/topic/clps711x', 'spi/topic/coldfire', 'spi/topic/davinci', 'spi/topic/dw' and 'spi/topic/falcon' into spi-linus 2014-01-23 13:07:05 +00:00