When L1 guest uses 5-level paging, it fails vm-entry to L2 due to
invalid host-state. It needs to add CR4_LA57 bit to nested CR4_FIXED1
MSR.
Signed-off-by: Chenyi Qiang <chenyi.qiang@intel.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Not zeroing the bitmap used for identifying the destination vCPUs for an
IOAPIC scan request in fixed delivery mode could lead to waking up unwanted
vCPUs. This patch zeroes the vCPU bitmap before passing it to
kvm_bitmap_or_dest_vcpus(), which is responsible for setting the bitmap
with the bits corresponding to the destination vCPUs.
Fixes: 7ee30bc132c6("KVM: x86: deliver KVM IOAPIC scan request to target vCPUs")
Signed-off-by: Nitesh Narayan Lal <nitesh@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In IOAPIC fixed delivery mode instead of flushing the scan
requests to all vCPUs, we should only send the requests to
vCPUs specified within the destination field.
This patch introduces kvm_get_dest_vcpus_mask() API which
retrieves an array of target vCPUs by using
kvm_apic_map_get_dest_lapic() and then based on the
vcpus_idx, it sets the bit in a bitmap. However, if the above
fails kvm_get_dest_vcpus_mask() finds the target vCPUs by
traversing all available vCPUs. Followed by setting the
bits in the bitmap.
If we had different vCPUs in the previous request for the
same redirection table entry then bits corresponding to
these vCPUs are also set. This to done to keep
ioapic_handled_vectors synchronized.
This bitmap is then eventually passed on to
kvm_make_vcpus_request_mask() to generate a masked request
only for the target vCPUs.
This would enable us to reduce the latency overhead on isolated
vCPUs caused by the IPI to process due to KVM_REQ_IOAPIC_SCAN.
Suggested-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Nitesh Narayan Lal <nitesh@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The L1 hypervisor may include the IA32_TIME_STAMP_COUNTER MSR in the
vmcs12 MSR VM-exit MSR-store area as a way of determining the highest
TSC value that might have been observed by L2 prior to VM-exit. The
current implementation does not capture a very tight bound on this
value. To tighten the bound, add the IA32_TIME_STAMP_COUNTER MSR to the
vmcs02 VM-exit MSR-store area whenever it appears in the vmcs12 VM-exit
MSR-store area. When L0 processes the vmcs12 VM-exit MSR-store area
during the emulation of an L2->L1 VM-exit, special-case the
IA32_TIME_STAMP_COUNTER MSR, using the value stored in the vmcs02
VM-exit MSR-store area to derive the value to be stored in the vmcs12
VM-exit MSR-store area.
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename function find_msr() to vmx_find_msr_index() in preparation for an
upcoming patch where we export it and use it in nested.c.
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename NR_AUTOLOAD_MSRS to NR_LOADSTORE_MSRS. This needs to be done
due to the addition of the MSR-autostore area that will be added in a
future patch. After that the name AUTOLOAD will no longer make sense.
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the function read_and_check_msr_entry() which just pulls some code
out of nested_vmx_store_msr(). This will be useful as reusable code in
upcoming patches.
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Correct a small inaccuracy in the shattering of vmx.c, which becomes
visible now that pmu_intel.c includes nested.h.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The "load IA32_PERF_GLOBAL_CTRL" bit for VM-entry and VM-exit should
only be exposed to the guest if IA32_PERF_GLOBAL_CTRL is a valid MSR.
Create a new helper to allow pmu_refresh() to update the VM-Entry and
VM-Exit controls to ensure PMU values are initialized when performing
the is_valid_msr() check.
Suggested-by: Jim Mattson <jmattson@google.com>
Co-developed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Oliver Upton <oupton@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add condition to prepare_vmcs02 which loads IA32_PERF_GLOBAL_CTRL on
VM-entry if the "load IA32_PERF_GLOBAL_CTRL" bit on the VM-entry control
is set. Use SET_MSR_OR_WARN() rather than directly writing to the field
to avoid overwrite by atomic_switch_perf_msrs().
Suggested-by: Jim Mattson <jmattson@google.com>
Co-developed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Oliver Upton <oupton@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The existing implementation for loading the IA32_PERF_GLOBAL_CTRL MSR
on VM-exit was incorrect, as the next call to atomic_switch_perf_msrs()
could cause this value to be overwritten. Instead, call kvm_set_msr()
which will allow atomic_switch_perf_msrs() to correctly set the values.
Define a macro, SET_MSR_OR_WARN(), to set the MSR with kvm_set_msr()
and WARN on failure.
Suggested-by: Jim Mattson <jmattson@google.com>
Co-developed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Oliver Upton <oupton@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a consistency check on nested vm-entry for host's
IA32_PERF_GLOBAL_CTRL from vmcs12. Per Intel's SDM Vol 3 26.2.2:
If the "load IA32_PERF_GLOBAL_CTRL"
VM-exit control is 1, bits reserved in the IA32_PERF_GLOBAL_CTRL
MSR must be 0 in the field for that register"
Suggested-by: Jim Mattson <jmattson@google.com>
Co-developed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Oliver Upton <oupton@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add condition to nested_vmx_check_guest_state() to check the validity of
GUEST_IA32_PERF_GLOBAL_CTRL. Per Intel's SDM Vol 3 26.3.1.1:
If the "load IA32_PERF_GLOBAL_CTRL" VM-entry control is 1, bits
reserved in the IA32_PERF_GLOBAL_CTRL MSR must be 0 in the field for that
register.
Suggested-by: Jim Mattson <jmattson@google.com>
Co-developed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Oliver Upton <oupton@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Create a helper function to check the validity of a proposed value for
IA32_PERF_GLOBAL_CTRL from the existing check in intel_pmu_set_msr().
Per Intel's SDM, the reserved bits in IA32_PERF_GLOBAL_CTRL must be
cleared for the corresponding host/guest state fields.
Suggested-by: Jim Mattson <jmattson@google.com>
Co-developed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Oliver Upton <oupton@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When KVM emulates a nested VMEntry (L1->L2 VMEntry), it switches mmu root
page. If nEPT is used, this will happen from
kvm_init_shadow_ept_mmu()->__kvm_mmu_new_cr3() and otherwise it will
happpen from nested_vmx_load_cr3()->kvm_mmu_new_cr3(). Either case,
__kvm_mmu_new_cr3() will use fast_cr3_switch() in attempt to switch to a
previously cached root page.
In case fast_cr3_switch() finds a matching cached root page, it will
set it in mmu->root_hpa and request KVM_REQ_LOAD_CR3 such that on
next entry to guest, KVM will set root HPA in appropriate hardware
fields (e.g. vmcs->eptp). In addition, fast_cr3_switch() calls
kvm_x86_ops->tlb_flush() in order to flush TLB as MMU root page
was replaced.
This works as mmu->root_hpa, which vmx_flush_tlb() use, was
already replaced in cached_root_available(). However, this may
result in unnecessary INVEPT execution because a KVM_REQ_TLB_FLUSH
may have already been requested. For example, by prepare_vmcs02()
in case L1 don't use VPID.
Therefore, change fast_cr3_switch() to just request TLB flush on
next entry to guest.
Reviewed-by: Bhavesh Davda <bhavesh.davda@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, a host perf_event is created for a vPMC functionality emulation.
It’s unpredictable to determine if a disabled perf_event will be reused.
If they are disabled and are not reused for a considerable period of time,
those obsolete perf_events would increase host context switch overhead that
could have been avoided.
If the guest doesn't WRMSR any of the vPMC's MSRs during an entire vcpu
sched time slice, and its independent enable bit of the vPMC isn't set,
we can predict that the guest has finished the use of this vPMC, and then
do request KVM_REQ_PMU in kvm_arch_sched_in and release those perf_events
in the first call of kvm_pmu_handle_event() after the vcpu is scheduled in.
This lazy mechanism delays the event release time to the beginning of the
next scheduled time slice if vPMC's MSRs aren't changed during this time
slice. If guest comes back to use this vPMC in next time slice, a new perf
event would be re-created via perf_event_create_kernel_counter() as usual.
Suggested-by: Wei Wang <wei.w.wang@intel.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The perf_event_create_kernel_counter() in the pmc_reprogram_counter() is
a heavyweight and high-frequency operation, especially when host disables
the watchdog (maximum 21000000 ns) which leads to an unacceptable latency
of the guest NMI handler. It limits the use of vPMUs in the guest.
When a vPMC is fully enabled, the legacy reprogram_*_counter() would stop
and release its existing perf_event (if any) every time EVEN in most cases
almost the same requested perf_event will be created and configured again.
For each vPMC, if the reuqested config ('u64 eventsel' for gp and 'u8 ctrl'
for fixed) is the same as its current config AND a new sample period based
on pmc->counter is accepted by host perf interface, the current event could
be reused safely as a new created one does. Otherwise, do release the
undesirable perf_event and reprogram a new one as usual.
It's light-weight to call pmc_pause_counter (disable, read and reset event)
and pmc_resume_counter (recalibrate period and re-enable event) as guest
expects instead of release-and-create again on any condition. Compared to
use the filterable event->attr or hw.config, a new 'u64 current_config'
field is added to save the last original programed config for each vPMC.
Based on this implementation, the number of calls to pmc_reprogram_counter
is reduced by ~82.5% for a gp sampling event and ~99.9% for a fixed event.
In the usage of multiplexing perf sampling mode, the average latency of the
guest NMI handler is reduced from 104923 ns to 48393 ns (~2.16x speed up).
If host disables watchdog, the minimum latecy of guest NMI handler could be
speed up at ~3413x (from 20407603 to 5979 ns) and at ~786x in the average.
Suggested-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce a new callback msr_idx_to_pmc that returns a struct kvm_pmc*,
and change kvm_pmu_is_valid_msr to return ".msr_idx_to_pmc(vcpu, msr) ||
.is_valid_msr(vcpu, msr)" and AMD just returns false from .is_valid_msr.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The leagcy pmu_ops->msr_idx_to_pmc is only called in kvm_pmu_rdpmc, so
this function actually receives the contents of ECX before RDPMC, and
translates it to a kvm_pmc. Let's clarify its semantic by renaming the
existing msr_idx_to_pmc to rdpmc_ecx_to_pmc, and is_valid_msr_idx to
is_valid_rdpmc_ecx; likewise for the wrapper kvm_pmu_is_valid_msr_idx.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When L1 don't use TPR-Shadow to run L2, L0 configures vmcs02 without
TPR-Shadow and install intercepts on CR8 access (load and store).
If L1 do not intercept L2 CR8 access, L0 intercepts on those accesses
will emulate load/store on L1's LAPIC TPR. If in this case L2 lowers
TPR such that there is now an injectable interrupt to L1,
apic_update_ppr() will request a KVM_REQ_EVENT which will trigger a call
to update_cr8_intercept() to update TPR-Threshold to highest pending IRR
priority.
However, this update to TPR-Threshold is done while active vmcs is
vmcs02 instead of vmcs01. Thus, when later at some point L0 will
emulate an exit from L2 to L1, L1 will still run with high
TPR-Threshold. This will result in every VMEntry to L1 to immediately
exit on TPR_BELOW_THRESHOLD and continue to do so infinitely until
some condition will cause KVM_REQ_EVENT to be set.
(Note that TPR_BELOW_THRESHOLD exit handler do not set KVM_REQ_EVENT
until apic_update_ppr() will notice a new injectable interrupt for PPR)
To fix this issue, change update_cr8_intercept() such that if L2 lowers
L1's TPR in a way that requires to lower L1's TPR-Threshold, save update
to TPR-Threshold and apply it to vmcs01 when L0 emulates an exit from
L2 to L1.
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This check is unnecessary as x86 update_cr8_intercept() which calls
this VMX/SVM specific callback already performs this check.
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are some duplicate code in kvm_pv_send_ipi when deal with ipi
bitmap. Add helper func to remove it, and eliminate odd out label,
get rid of unnecessary kvm_lapic_irq field init and so on.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When SYSCALL/SYSENTER ability check failed, cs and ss is inited but
remain not used. Delay initializing cs and ss until SYSCALL/SYSENTER
ability check passed.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Intel SDM section 25.2 OTHER CAUSES OF VM EXITS specifies the following
on INIT signals: "Such exits do not modify register state or clear pending
events as they would outside of VMX operation."
When commit 4b9852f4f3 ("KVM: x86: Fix INIT signal handling in various CPU states")
was applied, I interepted above Intel SDM statement such that
INIT_SIGNAL exit don’t consume the LAPIC INIT pending event.
However, when Nadav Amit run matching kvm-unit-test on a bare-metal
machine, it turned out my interpetation was wrong. i.e. INIT_SIGNAL
exit does consume the LAPIC INIT pending event.
(See: https://www.spinics.net/lists/kvm/msg196757.html)
Therefore, fix KVM code to behave as observed on bare-metal.
Fixes: 4b9852f4f3 ("KVM: x86: Fix INIT signal handling in various CPU states")
Reported-by: Nadav Amit <nadav.amit@gmail.com>
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 4b9852f4f3 ("KVM: x86: Fix INIT signal handling in various CPU states")
fixed KVM to also latch pending LAPIC INIT event when vCPU is in VMX
operation.
However, current API of KVM_SET_MP_STATE allows userspace to put vCPU
into KVM_MP_STATE_SIPI_RECEIVED or KVM_MP_STATE_INIT_RECEIVED even when
vCPU is in VMX operation.
Fix this by introducing a util method to check if vCPU state latch INIT
signals and use it in KVM_SET_MP_STATE handler.
Fixes: 4b9852f4f3 ("KVM: x86: Fix INIT signal handling in various CPU states")
Reported-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 4b9852f4f3 ("KVM: x86: Fix INIT signal handling in various CPU states")
fixed KVM to also latch pending LAPIC INIT event when vCPU is in VMX
operation.
However, current API of KVM_SET_VCPU_EVENTS defines this field as
part of SMM state and only set pending LAPIC INIT event if vCPU is
specified to be in SMM mode (events->smi.smm is set).
Change KVM_SET_VCPU_EVENTS handler to set pending LAPIC INIT event
by latched_init field regardless of if vCPU is in SMM mode or not.
Fixes: 4b9852f4f3 ("KVM: x86: Fix INIT signal handling in various CPU states")
Reviewed-by: Mihai Carabas <mihai.carabas@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's enough to check the exit value and issue a direct call to avoid
the retpoline for all the common vmexit reasons.
Of course CONFIG_RETPOLINE already forbids gcc to use indirect jumps
while compiling all switch() statements, however switch() would still
allow the compiler to bisect the case value. It's more efficient to
prioritize the most frequent vmexits instead.
The halt may be slow paths from the point of the guest, but not
necessarily so from the point of the host if the host runs at full CPU
capacity and no host CPU is ever left idle.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Eliminate wasteful call/ret non RETPOLINE case and unnecessary fentry
dynamic tracing hooking points.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The odd out jump label is really not needed. Get rid of
it by return true directly while r < 0 as suggested by
Paolo. This further lead to var changed being unused.
Remove it too.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 0bc48bea36 ("KVM: x86: update master clock before computing
kvmclock_offset")
switches the order of operations to avoid the conversion
TSC (without frequency correction) ->
system_timestamp (with frequency correction),
which might cause a time jump.
However, it leaves any other masterclock update unsafe, which includes,
at the moment:
* HV_X64_MSR_REFERENCE_TSC MSR write.
* TSC writes.
* Host suspend/resume.
Avoid the time jump issue by using frequency uncorrected
CLOCK_MONOTONIC_RAW clock.
Its the guests time keeping software responsability
to track and correct a reference clock such as UTC.
This fixes forward time jump (which can result in
failure to bring up a vCPU) during vCPU hotplug:
Oct 11 14:48:33 storage kernel: CPU2 has been hot-added
Oct 11 14:48:34 storage kernel: CPU3 has been hot-added
Oct 11 14:49:22 storage kernel: smpboot: Booting Node 0 Processor 2 APIC 0x2 <-- time jump of almost 1 minute
Oct 11 14:49:22 storage kernel: smpboot: do_boot_cpu failed(-1) to wakeup CPU#2
Oct 11 14:49:23 storage kernel: smpboot: Booting Node 0 Processor 3 APIC 0x3
Oct 11 14:49:23 storage kernel: kvm-clock: cpu 3, msr 0:7ff640c1, secondary cpu clock
Which happens because:
/*
* Wait 10s total for a response from AP
*/
boot_error = -1;
timeout = jiffies + 10*HZ;
while (time_before(jiffies, timeout)) {
...
}
Analyzed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
AMD CPUs now support XSAVES in a limited fashion (they require IA32_XSS
to be zero).
AMD has no equivalent of Intel's "Enable XSAVES/XRSTORS" VM-execution
control. Instead, XSAVES is always available to the guest when supported
on the host.
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Change-Id: I40dc2c682eb0d38c2208d95d5eb7bbb6c47f6317
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Hoist support for RDMSR/WRMSR of IA32_XSS from vmx into common code so
that it can be used for svm as well.
Right now, kvm only allows the guest IA32_XSS to be zero,
so the guest's usage of XSAVES will be exactly the same as XSAVEC.
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Change-Id: Ie4b0f777d71e428fbee6e82071ac2d7618e9bb40
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Hoist the vendor-specific code related to loading the hardware IA32_XSS
MSR with guest/host values on VM-entry/VM-exit to common x86 code.
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Change-Id: Ic6e3430833955b98eb9b79ae6715cf2a3fdd6d82
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When the guest can execute the XSAVES/XRSTORS instructions, use wrmsr to
set the hardware IA32_XSS MSR to guest/host values on VM-entry/VM-exit,
rather than the MSR-load areas. By using the same approach as AMD, we
will be able to use a common implementation for both (in the next
patch).
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Change-Id: I9447d104b2615c04e39e4af0c911e1e7309bf464
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When the guest can execute the XSAVES/XRSTORS instructions, set the
hardware IA32_XSS MSR to guest/host values on VM-entry/VM-exit.
Note that vcpu->arch.ia32_xss is currently guaranteed to be 0 on AMD,
since there is no way to change it.
Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Change-Id: Id51a782462086e6d7a3ab621838e200f1c005afd
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The kvm_vcpu variable, guest_xcr0_loaded, is a waste of an 'int'
and a conditional branch. VMX and SVM are the only users, and both
unconditionally pair kvm_load_guest_xcr0() with kvm_put_guest_xcr0()
making this check unnecessary. Without this variable, the predicates in
kvm_load_guest_xcr0 and kvm_put_guest_xcr0 should match.
Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Change-Id: I7b1eb9b62969d7bbb2850f27e42f863421641b23
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Volume 4 of the SDM says that IA32_XSS is supported
if CPUID(EAX=0DH,ECX=1):EAX.XSS[bit 3] is set, so only the
X86_FEATURE_XSAVES check is necessary (X86_FEATURE_XSAVES is the Linux
name for CPUID(EAX=0DH,ECX=1):EAX.XSS[bit 3]).
Fixes: 4d763b168e ("KVM: VMX: check CPUID before allowing read/write of IA32_XSS")
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Change-Id: I9059b9f2e3595e4b09a4cdcf14b933b22ebad419
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cache whether XSAVES is enabled in the guest by adding xsaves_enabled to
vcpu->arch.
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Change-Id: If4638e0901c28a4494dad2e103e2c075e8ab5d68
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename {vmx,nested_vmx}_vcpu_setup() to match what they really do.
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the initialization of vmx->guest_msrs[] from vmx_vcpu_setup() to
vmx_create_vcpu(), and put it right after its allocation.
This also is the preperation for next patch.
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
... It can be removed here because the same code is called later in
vmx_vcpu_reset() as the flow:
kvm_arch_vcpu_setup()
-> kvm_vcpu_reset()
-> vmx_vcpu_reset()
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the code that writes vmx->vpid to vmcs from vmx_vcpu_reset() to
vmx_vcpu_setup(), because vmx->vpid is allocated when creating vcpu and
never changed. So we don't need to update the vmcs.vpid when resetting
vcpu.
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replace the explicit declaration of "u64 reprogram_pmi" with the generic
macro DECLARE_BITMAP for all possible appropriate number of bits.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If we reach here with r = 0, we will reassign r = 0
unnecesarry, then do the label set_irqchip_out work.
If we reach here with r != 0, then we will do the label
work directly. So this if statement and r = 0 assignment
is redundant.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Generally, APICv for all vcpus in the VM are enable/disable in the same
manner. So, get_enable_apicv() should represent APICv status of the VM
instead of each VCPU.
Modify kvm_x86_ops.get_enable_apicv() to take struct kvm as parameter
instead of struct kvm_vcpu.
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Handle caching CR3 (from VMX's VMCS) into struct kvm_vcpu via the common
cache_reg() callback and drop the dedicated decache_cr3(). The name
decache_cr3() is somewhat confusing as the caching behavior of CR3
follows that of GPRs, RFLAGS and PDPTRs, (handled via cache_reg()), and
has nothing in common with the caching behavior of CR0/CR4 (whose
decache_cr{0,4}_guest_bits() likely provided the 'decache' verbiage).
This would effectivel adds a BUG() if KVM attempts to cache CR3 on SVM.
Change it to a WARN_ON_ONCE() -- if the cache never requires filling,
the value is already in the right place -- and opportunistically add one
in VMX to provide an equivalent check.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add helpers to prettify code that tests and/or marks whether or not a
register is available and/or dirty.
Suggested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
