The CLOCK_IN_OMAP4430 clock flag is not currently needed in the OMAP4
ES1 clock tree, and platform discrimination via clock flags is
deprecated in favor of the clkdev mechanism, so, drop it. (The OMAP4
clock tree autogeneration script has been updated accordingly.)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
The maximum DPLL multiplier (M) values for OMAP2xxx and OMAP3xxx are
one increment higher than they should be. See for example the
OMAP242x TRM Rev X Section 5.10.6 "Clock Generator Registers" and the
OMAP36xx TRM Rev C Table 3-202 "CM_CLKSEL1_PLL". Programming a 0 into
the DPLL's M register bitfield is valid for OMAP2/3 and indicates that
the DPLL should enter MN-bypass mode. Also, increase the minimum
multiplier (M) value for the DPLL rate rounding code from 1 to 2, to
ensure that it does not inadvertently put the DPLL into bypass.
Note that the register documentation in the OMAP2xxx and OMAP3xxx TRMs
does not make clear that the actual DPLL divider value (the "N") is
the content of the appropriate register bitfield for the N value,
_plus one_. (In other words, an N register bitfield of 0 indicates a
DPLL divider value of 1.) This is only clearly documented in the
OMAP4430 TRM, in, for example, OMAP4430 TRM Rev A Table 3-1167
"CM_CLKSEL_DPLL_USB".
While here, update copyrights, add kerneldoc for struct dpll_data,
drop the unused struct dpll_data.max_tolerance field, remove some
unnecessary #includes in DPLL-related code, and replace the #include
of <linux/module.h> with <linux/list.h>, which is what was really
needed. The OMAP4 clock autogenerator script has been updated
accordingly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
In 3630, DPLL4M2 output can be 96MHz or 192MHz (for SGX to run at
192). This patch has changes to support this feature. 96MHz clock is
generated by dividing 192Mhz clock by 2 using CM_CLKSEL_CORE register.
SGX can select Core Clock, 192MHz clock or CM_96M_FCLK as it's
functional clock. In summary changes done are:
1. Added a feature called omap3_has_192mhz_clk and enabled for 3630
2. Added a new clock node called omap_192m_alwon_ck
3. Made omap_96m_alwon_fck to derive its clock from omap_192m_alwon_ck
Signed-off-by: Vishwanath BS <Vishwanath.bs@ti.com>
[paul@pwsan.com: fixed whitespace]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Divider (M2, M3, M4, M5 and M6) field width has been increased by 1 bit
in 3630. This patch has changes to accommodate this in CM dynamically
based on chip version.
Basically new clock nodes have been added for 3630 DPLL4 M2,M3,M4,M5 and
M6 and value of these nodes are used if cpu type is 3630.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
[paul@pwsan.com: updated to apply on 2.6.34 queue; comments added]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DPLL4 for 3630 introduces a changed block called j type dpll, requiring
special divisor bits and additional reg fields. To allow for silicons to
use this, this is introduced as a flag and is enabled for 3630 silicon.
OMAP4 also has j type dpll for usb.
Tested with 3630 ZOOM3 and OMAP3430 ZOOM2
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vishwanath BS <Vishwanath.bs@ti.com>
[paul@pwsan.com: added some comments; updated copyrights and credits; fixed
some style issues]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds support in omap device layer to register devices
as early platform devices. Certain devices needed during system boot up
like timers, gpio etc can be registered as early devices. This will
allow for them to be probed very early on during system boot up.
This patch adds a parameter is_early_device in omap_device_build.
Depending on this parameter a call to early_platform_add_devices
or platform_register_device is made.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In OMAP3 Some modules like Smartreflex do not have the regular sysconfig
register.Instead clockactivity bits are part of another register at a
different bit position than the usual bit positions 8 and 9.
In OMAP4, a new scheme is available due to the new protocol
between the PRCM and the IPs. Depending of the scheme, the SYSCONFIG
bitfields position will be different.
The IP_REVISION register should be at offset 0x00.
It should contain a SCHEME field. From this we can determine whether
the IP follows legacy scheme or the new scheme.
31:30 SCHEME Used to distinguish between old scheme and current.
Read 0x0: Legacy protocol.
Read 0x1: New PRCM protocol defined for new OMAP4 IPs
For legacy IP
13:12 MIDLEMODE
11:8 CLOCKACTIVITY
6 EMUSOFT
5 EMUFREE
4:3 SIDLEMODE
2 ENAWAKEUP
1 SOFTRESET
0 AUTOIDLE
For new OMAP4 IP's, the bit position in SYSCONFIG is (for simple target):
5:4 STANDBYMODE (Ex MIDLEMODE)
3:2 IDLEMODE (Ex SIDLEMODE)
1 FREEEMU (Ex EMUFREE)
0 SOFTRESET
Unfortunately In OMAP4 also some IPs will not follow any of these
two schemes. This is the case at least for McASP, SmartReflex
and some security IPs.
This patch introduces a new field sysc_fields in omap_hwmod_sysconfig which
can be used by the hwmod structures to specify the offsets for the
sysconfig register of the IP.Also two static structures
omap_hwmod_sysc_type1 and omap_hwmod_sysc_type2 are defined
which can be used directly to populate the sysc_fields if the IP follows
legacy or new OMAP4 scheme. If the IP follows none of these two schemes
a new omap_hwmod_sysc_fields structure has to be defined and
passed as part of omap_hwmod_sysconfig.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Current implementation defines clock idle state indicators based on the
cpu information (cpu_is_omap24xx() or cpu_is_omap34xx()) in a system wide
manner. This patch extends the find_idlest() function in clkops to pass
back the idle state indicator for that clock, thus allowing idle state
indicators to be defined on a per clock basis if required.
This is specifically needed on AM35xx devices as the new IPSS clocks
indicates the idle status (0 is idle, 1 is ready) in a way just
opposite to how its handled in OMAP3 (0 is ready, 1 is idle).
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
[paul@pwsan.com: updated to apply after commit 98c45457 et seq.]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds counters to keep track of whether the powerdomain
logic or software controllable memory banks are turned off when
the power domain enters retention. During power domain retention
if logic gets turned off, the scenario is known as Open Switch Retention.
Also during retention s/w controllable memory banks of a power
domain can be chosen to be kept in retention or off.
This patch adds one counter per powerdomain to track the power domain
logic state during retention. Number of memory bank state counters
added depends on the number of software controllable memory banks
of the powerdomain. To view these counters do
cat ../debug/pm_debug/count
Signed-off-by: Thara Gopinath <thara@ti.com>
[paul@pwsan.com: conditional expressions simplified; counter increment
code moved to its own function]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds APIs pwrdm_read_logic_retst and
pwrdm_read_mem_retst for reading the next programmed
logic and memory state a powerdomain is to hit in event
of the next power domain state being retention.
These are needed for OSWR support.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The omap_device_[enable|idle|shutdown] functions print a warning
when called from an invalid state. Print the invalid state in
the warning messages. This also uses __func__ to get the function
name.
Also, move the entire print string onto a single line to facilitate
grepping or error messages. Recent discussions on LKML show
strong preference for grep-able code vs. strict 80 column limit.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The omap_device struct contains a 'struct platform_device'. Normally,
converting a platform_device pointer to an omap_device pointer
consists of simply doing a container_of(), as is done currently by the
to_omap_device() macro.
However, if this is attempted when using platform_device that has not
been created as part of the omap_device creation, the container_of()
will point to a memory location before the platform_device pointer
which will contain random data.
Therefore, we need a way to detect valid omap_device pointers. This
patch solves this by using the simple magic number approach.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add platform device for McPDM interface in OMAP4 and register
its memory and irq resources.
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define McPDM physical and L3 base address for OMAP4
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM3517/05 has few additional control module registers to control
the new IP's, like VPFE, USBOTG, CPGMAC.
This patch adds the bit defination for INTR_CLR and SW_RST control
register.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
EMMC can have two voltage supplies, Vcc and VccQ
which are implemented in the code as consumer
supplies vmmc and vmmc_aux.
If the regulator that supplies vmmc_aux is shared
with other consumers, then sending it to sleep
will disrupt those consumers. However, the
TWL4030-family regulators may have OFF remapped
to SLEEP, in which case 'regulator_disable()'
will put the regulator to sleep only when all
consumers are disabled - which is the desired
behaviour.
This patch adds a platform data field to allow
that option.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
An eMMC may be always powered on, so that the lowest
power saving state possible is sleeping. Add a field
to the platform data to indicate that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It has been discovered that, when eMMC is powered off, current
will flow from OMAP eMMC data pull-ups to the eMMC voltage supply.
Configuring pads for OMAP off-mode does not help because eMMC is
powered off independently of OMAP off-mode. Hence the pads are
now re-configured when eMMC is powered on or off.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves the setup code for GPIO's and Voltage
Regulators from the board file mmc-twl4030.c to the
driver omap_hsmmc.c. PBIAS and other system control
configuration remains in the board file.
Moving GPIO code to the driver makes the board initialisation
code independent of when GPIO's are defined. That makes the
board initialisation now entirely independent of its original
twl4030 roots.
Moving Voltage Regulator code to the driver allows for further
development of regulator support in the core MMC code. It also
permits the MMC core to be compiled as a module, because the
board code no longer calls MMC core functions.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds 'board-sdp-flash.c', which could be utilized
by boards similar to 3430SDP. (For ex: 2430sdp, 36030sdp).
This file does initialization for all three flash devices present
in SDP boards (NOR, NAND, OneNAND), by finding there 'cs' number
dynamically using switch setting information (S8: 1-4).
This also expects partition information from core board files (for
ex: board-3430sdp.c). Which allows to choose different default
partitions for different boards.
A new structure is created for this purpose: 'flash_partitions'
in 'mach/board-sdp.h'. This has two members:
1. struct mtd_partition *parts
2. int nr_parts
A board file is expected to fill this structure and pass it to
'sdp-flsash-init'. Partition information should be passed in
structure array of 'flash_partitions'. Partition information should
be passed in below sequence in array:
NOR
OneNAND
NAND
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Introducing 'gpmc-nand.c' for GPMC specific NAND init.
For example: GPMC timing parameters and all.
This patch also migrates gpmc related calls from 'nand/omap2.c'
to 'gpmc-nand.c'.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Change the way McBSP registers are updated: use cached values instead of
relying upon those read back from the device.
With this patch, I have finally managed to get rid of all random
playback/recording hangups on my OMAP1510 based Amstrad Delta hardware. Before
that, values read back from McBSP registers to be used for updating them
happened to be errornous.
From the hardware side, the issue appeared to be caused by a relatively high
power requirements of an external USB adapter connected to the board's printer
dedicated USB port.
I think there is one important point that makes this patch worth of applying,
apart from my hardware quality. With the current code, if it ever happens to
any machine, no matter if OMAP1510 or newer, to read incorrect value from a
McBSP register, this wrong value will get written back without any checking.
That can lead to hardware damage if, for example, an input pin is turned into
output as a result.
Applies on top of patch 3 from this series:
[PATCH v9 3/4] OMAP: McBSP: Introduce caching in register write operations
Tested on OMAP1510 based Amstrad Delta using linux-omap for-next, commit
fb7380d70e041e4b3892f6b19dff7efb609d15a4 (2.6.33-rc3+ dated 2010-01-11).
Compile-tested with omap_3430sdp_defconfig.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Determine cache size required per McBSP port at init time, based on
processor type running on.
Allocate space for storing cached copies of McBSP register values at
port request.
Modify omap_msbcp_write() function to update the cache with every
register write operation.
Modify omap_mcbsp_read() to support reading from cache or hardware.
Update MCBSP_READ() macro for modified omap_mcbsp_read() function API.
Introduce a new macro that reads from the cache.
Tested on OMAP1510 based Amstrad Delta using linux-omap for-next, commit
fb7380d70e041e4b3892f6b19dff7efb609d15a4 (2.6.33-rc3+ dated 2010-01-11).
Compile-tested with: omap_perseus2_730_defconfig, omap_generic_1610_defconfig,
omap_generic_2420_defconfig, omap_2430sdp_defconfig, omap_3430sdp_defconfig,
omap_4430sdp_defconfig with CONFIG_OMAP_MCBSP=y selected.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_MCBSP_READ()/_WRITE() macros and omap_mcbsp_read()/_write() functions
accept McBSP register base address as an argument. In order to support
caching, that must be replaced with an address of the omap_mcbsp structure
that would provide addresses for both register AND cache access.
Since OMAP_ prefix seems obvious in macro names, drop it off in order to
minimize line wrapping throughout the file.
Tested on OMAP1510 based Amstrad Delta using linux-omap for-next, commit
fb7380d70e041e4b3892f6b19dff7efb609d15a4 (2.6.33-rc3+ dated 2010-01-11).
Compile-tested with omap_3430sdp_defconfig.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are several places where readw()/writew() functions are used instead of
OMAP_MCBSP_READ()/WRITE() macros for manipulating McBSP registers. Replace
them with macros to ensure consistent behaviour after caching is introduced.
Tested on OMAP1510 based Amstrad Delta.
Compile-tested with omap_3430sdp_defconfig.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There was a potential risk that the following "memset" could override
its range if a given address was not the 1st entry of a
largepage. This is not the case for "iovmm".
Reported-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There was a potential risk that the following "memset" could override
its range if a given address was not the 1st entry of a
supersection. This is not the case for "iovmm".
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is just a cleanup, but adds a few macros here, which can be used
in the proceeding patches.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert OMAP based boards to use physmap-flash. Refreshed against today's
Linux omap kernel tree
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Set up METHOD_GPIO_44XX instead of trying to use the METHOD_GPIO_24XX.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we can include it easily as needed also for .S files.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix dmtimer.c for multi-omap boot. Also remove legacy
clk_enable/disable wrappers that are no longer needed.
Note that the clock handling should be further improved
to make use of the clock aliases.
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are no longer needed. Note that zoom boards
should now set their own function in uncompress.h
and debug-macro.S for the external UART.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define arch_decomp_setup() the same way as some other
architectures do. Use arch_id to configure the debug uart
based on the machine_is by storing it into the uart
scratchpad register for DEBUG_LL code to use.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we don't have conflicts with the defines
with compiling in multiple omaps. Set the addresses
for uarts in struct omap_globals for the early serial
init code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
I have found an access to already released memory in
clk_debugfs_register_one() function.
Signed-off-by: Marek Skuczynski <mareksk7@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The only usage of _toggle_gpio_edge_triggering is in
an #ifdef CONFIG_ARCH_OMAP1 block, so only provide it if
CONFIG_ARCH_OMAP1 is defined, too.
This fixes a compiler warning:
arch/arm/plat-omap/gpio.c:758: warning: '_toggle_gpio_edge_triggering' defined but not used
when compiling for ARCH_OMAP2, ARCH_OMAP3 or ARCH_OMAP4.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some HW blocks have errata which requires specific slave idle mode
under certain conditions.
This patch adds an hwmod API to allow setting slave idlemode
ensuring that any SYSCONFIG register updates go through hwmod.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
