It was a typo in the function
name, it should be lnbh24_attach, and not lnbp24_attach.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add last piece of code to support ST STV0900 dual demodulator.
The IC consist of two dependent parts.
It may use single or dual mode.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The IC consist of two dependent parts.
It may use single or dual mode.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The controller consist of two independent parts.
Every part is similar to LNBP21, but has configurable i2c address.
It is used in NetUP Dual DVB-S2 CI card.
http://linuxtv.org/wiki/index.php/NetUP_Dual_DVB_S2_CI
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tuner is used in NetUP Dual DVB-S2 CI card.
http://linuxtv.org/wiki/index.php/NetUP_Dual_DVB_S2_CI
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
[mchehab@redhat.com: removed a wrong header: "cx23885.h"]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the following build error:
drivers/media/dvb/siano/smsusb.o: In function `get_order':
include/asm-generic/page.h:10: multiple definition of `sms_dbg'
drivers/media/dvb/siano/sms1xxx.o:include/asm-generic/page.h:10: first defined here
drivers/media/dvb/siano/smsdvb.o: In function `get_order':
include/asm-generic/page.h:10: multiple definition of `sms_dbg'
drivers/media/dvb/siano/sms1xxx.o:include/asm-generic/page.h:10: first defined here
Thanks to Mauro Carvalho Chehab for his original patch to address this issue.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As pointed out by Mauro Chehab, we should always use EXPORT_SYMBOL_GPL
instead of EXPORT_SYMBOL wherever possible.
A message was posted to the linux-media mailing list about this, checking
with Uri Shkolnik of Siano Mobile Silicon if this is okay to convert.
As per Uri's response to this email, it is OK for us to make this conversion.
http://www.spinics.net/lists/linux-media/msg02200.html
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The smsdvb module was separated from the core and usb code. This change loads
smsdvb automatically for driver configurations that depend on it.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix checkpatch.pl violations introduced by previous changeset:
ERROR: do not use C99 // comments
156: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1373:
+//#ifdef DVB_CORE
ERROR: do not use C99 // comments
157: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1374:
+// smsdvb_unregister();
ERROR: do not use C99 // comments
158: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1375:
+//#endif
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
163: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1380:
+EXPORT_SYMBOL(smscore_onresponse);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
164: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1381:
+EXPORT_SYMBOL(sms_get_board);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
165: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1382:
+EXPORT_SYMBOL(sms_debug);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
166: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1383:
+EXPORT_SYMBOL(smscore_putbuffer);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
167: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1384:
+EXPORT_SYMBOL(smscore_registry_getmode);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
168: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1385:
+EXPORT_SYMBOL(smscore_register_device);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
169: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1386:
+EXPORT_SYMBOL(smscore_set_board_id);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
170: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1387:
+EXPORT_SYMBOL(smscore_start_device);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
171: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1388:
+EXPORT_SYMBOL(smsusb_id_table);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
172: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1389:
+EXPORT_SYMBOL(smscore_unregister_device);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
173: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1390:
+EXPORT_SYMBOL(smscore_getbuffer);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
174: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1391:
+EXPORT_SYMBOL(smscore_get_device_mode);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
175: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1392:
+EXPORT_SYMBOL(smscore_register_client);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
176: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1393:
+EXPORT_SYMBOL(smscore_unregister_hotplug);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
177: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1394:
+EXPORT_SYMBOL(smsclient_sendrequest);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
178: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1395:
+EXPORT_SYMBOL(smscore_unregister_client);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
179: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1396:
+EXPORT_SYMBOL(smscore_get_board_id);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
180: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1397:
+EXPORT_SYMBOL(smscore_register_hotplug);
WARNING: line over 80 characters
391: FILE: linux/drivers/media/dvb/siano/smscoreapi.h:398:
+extern int smscore_get_fw_filename(struct smscore_device_t *coredev, int mode, char* filename);
ERROR: "foo* bar" should be "foo *bar"
391: FILE: linux/drivers/media/dvb/siano/smscoreapi.h:398:
+extern int smscore_get_fw_filename(struct smscore_device_t *coredev, int mode, char* filename);
WARNING: line over 80 characters
392: FILE: linux/drivers/media/dvb/siano/smscoreapi.h:399:
+extern int smscore_send_fw_file(struct smscore_device_t *coredev, u8* ufwbuf,int size);
ERROR: "foo* bar" should be "foo *bar"
392: FILE: linux/drivers/media/dvb/siano/smscoreapi.h:399:
+extern int smscore_send_fw_file(struct smscore_device_t *coredev, u8* ufwbuf,int size);
ERROR: space required after that ',' (ctx:VxV)
392: FILE: linux/drivers/media/dvb/siano/smscoreapi.h:399:
+extern int smscore_send_fw_file(struct smscore_device_t *coredev, u8* ufwbuf,int size);
^
WARNING: __func__ should be used instead of gcc specific __FUNCTION__
489: FILE: linux/drivers/media/dvb/siano/smsusb.c:443:
+ printk(KERN_INFO"%s Entering status %d.\n", __FUNCTION__, msg.event);
WARNING: __func__ should be used instead of gcc specific __FUNCTION__
501: FILE: linux/drivers/media/dvb/siano/smsusb.c:455:
+ printk(KERN_INFO "%s Entering.\n", __FUNCTION__);
ERROR: space prohibited before that '++' (ctx:WxB)
505: FILE: linux/drivers/media/dvb/siano/smsusb.c:459:
+ for (i = 0; i < intf->cur_altsetting->desc.bNumEndpoints; i ++)
^
WARNING: __func__ should be used instead of gcc specific __FUNCTION__
517: FILE: linux/drivers/media/dvb/siano/smsusb.c:471:
+ __FUNCTION__, rc);
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
[mchehab@redhat.com: sms_dbg were declared on 3 different files]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Import the following changes from Uri Shkolnik
* Two-ways merge with Siano internal repository
* Continuing with DVB sub-system separation
* kconfig and makefile updates
* Code cleanup
This is a work-in-progress sync with Siano's internal repository.
Some changes had to be altered or dropped in order not to break the build.
This breaks normal operation for the current driver, but it is being committed
now for tracking purposes.
These changes introduce the following checkpatch.pl violations:
ERROR: do not use C99 // comments
156: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1373:
+//#ifdef DVB_CORE
ERROR: do not use C99 // comments
157: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1374:
+// smsdvb_unregister();
ERROR: do not use C99 // comments
158: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1375:
+//#endif
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
163: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1380:
+EXPORT_SYMBOL(smscore_onresponse);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
164: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1381:
+EXPORT_SYMBOL(sms_get_board);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
165: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1382:
+EXPORT_SYMBOL(sms_debug);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
166: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1383:
+EXPORT_SYMBOL(smscore_putbuffer);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
167: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1384:
+EXPORT_SYMBOL(smscore_registry_getmode);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
168: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1385:
+EXPORT_SYMBOL(smscore_register_device);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
169: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1386:
+EXPORT_SYMBOL(smscore_set_board_id);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
170: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1387:
+EXPORT_SYMBOL(smscore_start_device);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
171: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1388:
+EXPORT_SYMBOL(smsusb_id_table);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
172: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1389:
+EXPORT_SYMBOL(smscore_unregister_device);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
173: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1390:
+EXPORT_SYMBOL(smscore_getbuffer);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
174: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1391:
+EXPORT_SYMBOL(smscore_get_device_mode);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
175: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1392:
+EXPORT_SYMBOL(smscore_register_client);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
176: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1393:
+EXPORT_SYMBOL(smscore_unregister_hotplug);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
177: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1394:
+EXPORT_SYMBOL(smsclient_sendrequest);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
178: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1395:
+EXPORT_SYMBOL(smscore_unregister_client);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
179: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1396:
+EXPORT_SYMBOL(smscore_get_board_id);
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
180: FILE: linux/drivers/media/dvb/siano/smscoreapi.c:1397:
+EXPORT_SYMBOL(smscore_register_hotplug);
WARNING: line over 80 characters
391: FILE: linux/drivers/media/dvb/siano/smscoreapi.h:398:
+extern int smscore_get_fw_filename(struct smscore_device_t *coredev, int mode, char* filename);
ERROR: "foo* bar" should be "foo *bar"
391: FILE: linux/drivers/media/dvb/siano/smscoreapi.h:398:
+extern int smscore_get_fw_filename(struct smscore_device_t *coredev, int mode, char* filename);
WARNING: line over 80 characters
392: FILE: linux/drivers/media/dvb/siano/smscoreapi.h:399:
+extern int smscore_send_fw_file(struct smscore_device_t *coredev, u8* ufwbuf,int size);
ERROR: "foo* bar" should be "foo *bar"
392: FILE: linux/drivers/media/dvb/siano/smscoreapi.h:399:
+extern int smscore_send_fw_file(struct smscore_device_t *coredev, u8* ufwbuf,int size);
ERROR: space required after that ',' (ctx:VxV)
392: FILE: linux/drivers/media/dvb/siano/smscoreapi.h:399:
+extern int smscore_send_fw_file(struct smscore_device_t *coredev, u8* ufwbuf,int size);
^
WARNING: __func__ should be used instead of gcc specific __FUNCTION__
489: FILE: linux/drivers/media/dvb/siano/smsusb.c:443:
+ printk(KERN_INFO"%s Entering status %d.\n", __FUNCTION__, msg.event);
WARNING: __func__ should be used instead of gcc specific __FUNCTION__
501: FILE: linux/drivers/media/dvb/siano/smsusb.c:455:
+ printk(KERN_INFO "%s Entering.\n", __FUNCTION__);
ERROR: space prohibited before that '++' (ctx:WxB)
505: FILE: linux/drivers/media/dvb/siano/smsusb.c:459:
+ for (i = 0; i < intf->cur_altsetting->desc.bNumEndpoints; i ++)
^
WARNING: __func__ should be used instead of gcc specific __FUNCTION__
517: FILE: linux/drivers/media/dvb/siano/smsusb.c:471:
+ __FUNCTION__, rc);
total: 7 errors, 23 warnings, 524 lines checked
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the usb_device_id table to the smsusb module in preparation for the
sms1xxx module to be split into sub-modules. This will allow the smsusb
driver to start up automatically upon insertion of the USB device.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sms1xxx driver will be broken down into smaller modules,
so the original name, smsusb, is more appropriate.
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Nobody uses struct smsdvb_client_t other than smsdvb.c --
this does not need to be inside smscoreapi.h
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver infrared remote code part is altered to switch to a work queue.
Also ir_codes table moved to ir-common module for shared access.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver already has DMA buffer organized like ringbuffer,
so it is easy to switch to a work queue.
Length of ringbuffer can easily be increased, if someone need it.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hi there!
While having a look at the allocation of struct dvb_frontend in *_attach
functions, I found some cases calling memset after kzalloc. This is
redundant, and the attached patch removes these calls.
I also changed one case calling kmalloc and memset to kzalloc.
Regards
Matthias
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For i2c normal work, we need to slow down the bus speed. However, the
slow down breaks the eeprom firmware load. So, use normal speed for
eeprom booting and then restore the i2c speed after that.
It should also be noticed that no other I2C transfer should be in course
while booting from eeprom, otherwise, tda10046 goes into an instable
state. So, proper locking are needed at the i2c bus master.
Tested with saa7134 MSI TV @nyware A/D board, that comes with an eeprom
with firmware version 29.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add MC44S803 support to AF9015 driver.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Data debug for i2c transactions was provided by the functions
called by dib0700_i2c_xfer_legacy, but not dib0700_i2c_xfer_new.
This patch adds the missing data debug dumps to dib0700_i2c_xfer_new.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some cards uses cx24116 LNB_DC pin for LNB power control,
some not uses, some uses it different way, like HVR-4000.
Tested-by : Edgar Hucek <gimli@dark-green.com>
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Here is a patch which adds some documentation about meanings of the
the lnbp21 system register bits.
Signed-off-by: Hans Werner <hwerner4@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new Avermedia Volar-X is shipped with a new remote(RM-KS). The attached
patch add a new option to the remote parameter of dvb_usb_af9015 for this
remote.
Signed-off-by: Felipe Morales Moreno <felipe.morales.moreno@gmail.com>
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove dual_mode module param. Possible 2nd FE seems not to be buggy
any more and therefore can be enabled as default.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make it clear that a failure in dib0700_i2c_enumeration is a fatal condition
and we cannot continue. If the failure occurs, do not attempt to attach to
the tuner.
Problem Noticed the issue when debugging an i2c issue a YUAN High-Tech
STK7700PH for user Roshan Karki <roshan@olenepal.org>.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make it clear that the address is in hex format.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds the IR data structure to the configuration datastructure of the
Hauppauge WinTV Nova-TD USB stick (52009)
Provided remote control is the same as theone provided with the Nova-T500
Card.
Signed-off-by: Arne Luehrs <arne.luehrs@googlemail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add new USB ID 1b80:e39b for KWorld DVB-T 395U. This device revision does
have Quantek QT1010 silicon tuner.
Thanks-to: Ray Chen <swyear@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The conversion to video_ioctl2 is the first phase to converting this driver
to the latest v4l2 framework.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now there is a card, which uses cx24116 to control LNB DC voltage.
It is DVBWorld DVBS2 PCI-e 2005.
The patch is nedded to add support for that card.
1. Rename CMD_SET_TONEPRE to CMD_LNBDCLEVEL.
2. Fill set_voltage with actually control voltage code.
3. Correct set_tone to not affect voltage.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Beat Michel Liechti <bml303@gmail.com>
Tuning was broken on FireDTV S2 (and presumably FloppyDTV S2) because a
wrong opcode was sent. The box only gave "not implemented" responses.
Changing the opcode to _TUNE_QPSK2 fixes this for good.
Cc: stable@kernel.org
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Eliminate
drivers/media/dvb/firewire/firedtv-avc.c: In function 'debug_fcp':
drivers/media/dvb/firewire/firedtv-avc.c:156: warning: format '%d' expects type 'int', but argument 5 has type 'size_t'
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
in Hz not kHz, and a comment incorrectly says MHz instead of Hz. I
don't know if this caused real problems anywhere
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For legacy applications stv0899 performs search only first time after insmod
due to not set DVBFE_ALGO_SEARCH_AGAIN bit
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
zl10353 i2c-gate was always closed and due to that devices having tuner
behind i2c-gate were broken. Add module configuration which allows disabling
i2c-gate only when really needed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With (some) Technisat cards you cannot run multiple DVB applications
in parallel and switch the channel at the same time.
There seems to be a problem on the interfaces or even inside the flexcop-device
that can't handle interruption on the streaming interface.
This patch adds a watchdog to check whether data is supposed to come in
(streaming PIDs are requested) and if no data is seen within 400ms (default) it
resets the streaming/pid-filtering hardware.
This patch is urgently needed to support the rev 2.8 of the hardware and solves
problem occassionally seen on older hardware.
Signed-off-by: Uwe Bugla <uwe.bugla@gmx.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I found that the function fdtv_frontend_init in the file firedtv-fe.c was
missing a case for FIREDTV_DVB_S2 which resulted in "frequency limits
undefined" errors in syslog.
Signed-off-by: Beat Michel Liechti <bml303@gmail.com>
Change by Stefan R: combine it with case case FIREDTV_DVB_S as
originally suggested by Beat Michel. This enables FE_CAN_FEC_AUTO also
for FireDTV-S2 devices which is possible as long as only DVB-S channels
are used. FE_CAN_FEC_AUTO would be wrong for DVB-S2 channels, but those
cannot be used yet since the driver is not yet converted to S2API.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Combination of the following changes:
Mon, 23 Feb 2009 14:21:10 +0100 (CET)
firedtv: reinstate debug logging option
Henrik Kurelid tells me that FCP debug logging (which I removed during
cleanups) is still useful when working on driver issues together with
end users. So bring it back in an updated form with only 60% of the
original code footprint.
Logging can be enabled with
# echo -1 > /sys/module/firedtv/parameters/debug
1 instead of -1 enables only FCP header logging,
2 instead of -1 enables only hexdumps of the entire FCP frames.
0 switches logging off again.
Fri, 20 Feb 2009 20:54:27 +0100 (CET)
firedtv: build fix for INPUT=m and DVB_FIREDTV=y
Thu, 19 Feb 2009 20:40:39 +0100
firedtv: use msecs_to_jiffies
Pointed out by Mauro Carvalho Chehab.
Sun Feb 15 20:50:46 CET 2009
firedtv: some more housekeeping
Fix an old checkpatch warning and a new compiler warning.
Sun Feb 15 15:33:17 CET 2009
firedtv: rename a file once more
At the moment, about a third of avc.c is specific to FireDTVs rather
than generic AV/C code. Rename it to firedtv-avc.c.
Sun Feb 15 15:33:17 CET 2009
firedtv: dvb demux: more compact channels backing store
Replace struct firedtv_channel { bool active; int pid; } channel[16];
by unsigned long channel_active; u16 channel_pid[16];.
Sun Feb 15 15:33:17 CET 2009
firedtv: dvb demux: some simplifications
c->active was unnecessarily cleared twice.
Also, by marking the channel inactive before the for loop,
the loop becomes identical with fdtv_channel_collect().
Sun Feb 15 15:33:17 CET 2009
firedtv: dvb demux: remove a bogus loop
This loop is unnecessary because
- only active channel[].pid's will be sent to the device,
- when a channel is activated, its pid is set to dvbdmxfeed->pid.
Perhaps the original code was there because it was initially not fully
covered by the fdtv->demux_mutex.
Sun Feb 15 15:33:17 CET 2009
firedtv: dvb demux: fix mutex protection
fdtv_start_feed() accessed the channel list unsafely.
Fully serialize it with itself and fdtv_stop_feed().
Sun Feb 15 15:33:17 CET 2009
firedtv: dvb demux: fix missing braces
Original code was:
...
case DMX_TS_PES_OTHER:
//Dirty fix to keep firesat->channel pid-list up to date
for(k=0;k<16;k++){
if(firesat->channel[k].active == 0)
firesat->channel[k].pid =
dvbdmxfeed->pid;
break;
}
channel = firesat_channel_allocate(firesat);
break;
default:
...
Looks bogus in several respects. For now let's just add braces to the if
because that seems to be what the author meant.
Sun Feb 15 15:33:17 CET 2009
firedtv: allow build without input subsystem
!CONFIG_INPUT is very unlikely on systems on which firedtv is of
interest. But we can easily support it.
Sun Feb 15 15:33:17 CET 2009
firedtv: replace EXTRA_CFLAGS by ccflags
The former are deprecated.
The latter can depend on Kconfig variables.
Sun Feb 15 15:33:17 CET 2009
firedtv: concentrate ieee1394 dependencies
Move the entire interface with drivers/ieee1394 to firedtv-1394.c.
Move 1394-independent module initialization code to firedtv-dvb.c.
This prepares interfacing with drivers/firewire.
Sun Feb 15 15:33:17 CET 2009
firedtv: amend Kconfig menu prompt
Sun Feb 15 15:33:17 CET 2009
firedtv: remove kernel version compatibility macro
Sun Feb 15 15:33:17 CET 2009
firedtv: combine header files
avc.h and firedtv-*.h are small and currently not shared with other
drivers, hence concatenate them all into firedtv.h.
Sun Feb 15 15:33:17 CET 2009
firedtv: misc style touch-ups
Standardize on lower-case hexadecimal constants. Adjust whitespace.
Omit unnecessary pointer type casts and an unnecessary list head
initialization. Use dev_printk.
Wed Feb 11 21:21:04 CET 2009
firedtv: avc, ci: remove unused constants
Wed Feb 11 21:21:04 CET 2009
firedtv: avc: remove bitfields from read descriptor response operands
Don't use bitfields in struct types of on-the-wire data.
Wed Feb 11 21:21:04 CET 2009
firedtv: avc: remove bitfields from DSD command operands
Don't use bitfields in struct types of on-the-wire data.
Wed Feb 11 21:21:04 CET 2009
firedtv: avc: header file cleanup
Remove unused constants and declarations.
Move privately used constants into .c files.
Wed Feb 11 21:21:04 CET 2009
firedtv: avc: remove bitfields from FCP frame types
Don't use bitfields in struct types of on-the-wire data.
Also move many privately used constants from avc.h to avc.c
and remove some unused constants.
Sun, 18 Jan 2009 16:30:00 +0100 (CET)
firedtv: avc: fix offset in avc_tuner_get_ts
The parentheses were wrong. It didn't matter though because this code
only writes a 0 into an area which is already initialized to 0.
Sun, 18 Jan 2009 16:30:00 +0100 (CET)
firedtv: avc: reduce stack usage, remove two typedefs
It is safe to share a memory buffer for command frame and response frame
because the response data come in after the command frame was last used.
Even less stack would be required if only the actual required frame size
instead of the entire FCP register size was allocated.
Also, rename the defined types AVCCmdFrm and AVCRspFrm to
struct avc_command_frame and struct avc_response_frame.
TODO: Remove the bitfields in these types.
Sun, 18 Jan 2009 16:30:00 +0100 (CET)
firedtv: cmp: move code to avc
Sun, 18 Jan 2009 16:30:00 +0100 (CET)
firedtv: iso: move code to firedtv-1394
Sun, 18 Jan 2009 16:30:00 +0100 (CET)
firedtv: iso: remove unnecessary struct type definitions
Sun, 18 Jan 2009 16:30:00 +0100 (CET)
firedtv: iso: style changes and fixlets
Add cleanup after failure in setup_iso_channel.
Replace printk() by dv_err().
Decrease indentation level in rawiso_activity_cb().
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Combination of the following changes:
Sat, 17 Jan 2009 14:47:34 +0100
firedtv: rename variables and functions from firesat to firedtv
Signed-off-by: Rambaldi <Rambaldi@xs4all.nl>
Additional changes by Stefan Richter:
Renamed struct firedtv *firedtv to struct firedtv *fdtv and
firedtv_foo_bar() to fdtv_foo_bar() for brevity.
Sat, 17 Jan 2009 13:07:44 +0100
firedtv: rename files from firesat to firedtv
Signed-off-by: Rambaldi <Rambaldi@xs4all.nl>
Additional changes by Stefan Richter:
Name the directory "firewire" instead of "firedtv".
Standardize on "-" instead of "_" in file names, because that's what
drivers/firewire/ and drivers/media/dvb/dvb-usb/ use too.
Build fix.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
SPIN_LOCK_UNLOCKED is deprecated. The following makes the change suggested
in Documentation/spinlocks.txt
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
There was a bug causing the initialization to fail if adapter number was
greater than zero. The adapter was however registered which caused the driver
to oops the second time initialization was tried.
Signed-off-by: Henrik Kurelid <henrik@kurelid.se>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Parsed and used the length_field() of the PMT message instead of using
the length field of the message struct, which does not seem to be filled
correctly by e.g. MythTV.
Signed-off-by: Henrik Kurelid <henrik@kurelid.se>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
