This patch allows iscsiadm to manage iSCSI target information stored on
adapter flash on per host basis.
The sysfs entries will look as cited below:
/sys/bus/iscsi_flashnode/devices/flashnode_sess-<host_no>:<flashnode_id>/<session attrs>
/sys/bus/iscsi_flashnode/devices/flashnode_conn-<host_no>:<flashnode_id>:<conn_id>/<conn attrs>
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
While probe Skip retry of initialize_adapter only for ISP82XX and ISP83XX.
We need to retry initialize_adapter for ISP40XX.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
If flash read for FLT fails, we are assigning wrong default
address for CHAP table in FLT, which will cause CHAP table
read/write to wrong address.
Fix:
Assign correct default CHAP table address to FLT.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds dual flash firmware support for Series 7 and above controllers.
[thenzl: used ssleep(10) instead udelay]
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The variable 'data' is initialized but never used
otherwise, so remove the unused variable.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
Request queue count holds the information about free space in request queue
which has to be manipulated based on request in and out pointer.
But in driver response path, this count was incremented unconditionally,
which could move req_in pointer beyond req_out pointer.
This scenario leads fw hang during IO.
Solution:
Request queue count manipulation has to be done in IO path only, keeping
req_in and req_out pointer two IOCB count away
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Move "Incorrect function ID" print message in case INTX interrupt
from DEBUG2 to DEBUG7. This will avoid floods of this message if
DEBUG2 is enabled.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use function int_to_scsilun() in qla4xxx_reset_lun() to convert
integer value comming from scsi_transport to scsi LUN address format.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In case of firmware hung we need to call "mailbox_premature_completion" to
complete any pending mbox command as firmware is not alive.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For ISP83XX set graceful reset bit in IDC_DRV_CTRL
if reset is issued by application
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
ISP83XX check is missing in function get_fw_boot_info() because of this
qla4xxx will not export boot target to sysfs and iscsistart cannot issue
login to boot target.
Fix:
Added check for ISP83XX in function get_fw_boot_info()
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Problem Description:
Disabling pause frames might cause hardware wedging needing a power cycle.
This might happen if the Eport is not initialized and is in reset.
Solution:
Before disabling pause frames ensure that eport is out of reset.
Signed-off-by: Manish Dusane <manish.dusane@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For the stpg_endio path we are not evaluating the sense. The bug
is that
1. The error value is set to -EIO when there is sense, so we hit the first
error check and always return SCSI_DH_IO.
2. h->senselen is set to zero in submit_stpg. It is not later set to
req->sense_len like in the synchrounous exection paths, so we must
check the req->sense_len field.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The service parameters for the VPI/RPIs were incorrect, resulting in
lower utilization
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixed NMI watch dog panic's when resetting the hba.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If a result of the SMP discover function is PHY VACANT,
the content of discover response structure (dr) is not valid.
It sometimes happens that dr->attached_sas_addr can contain
even SAS address of other phy. In such case an invalid phy
is created, what causes NULL pointer dereference during
destruction of expander's phys.
So if a result of SMP function is PHY VACANT, the content of discover
response structure (dr) must not be copied to phy structure.
This patch fixes the following bug:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000030
IP: [<ffffffff811c9002>] sysfs_find_dirent+0x12/0x90
Call Trace:
[<ffffffff811c95f5>] sysfs_get_dirent+0x35/0x80
[<ffffffff811cb55e>] sysfs_unmerge_group+0x1e/0xb0
[<ffffffff813329f4>] dpm_sysfs_remove+0x24/0x90
[<ffffffff8132b0f4>] device_del+0x44/0x1d0
[<ffffffffa016fc59>] sas_rphy_delete+0x9/0x20 [scsi_transport_sas]
[<ffffffffa01a16f6>] sas_destruct_devices+0xe6/0x110 [libsas]
[<ffffffff8107ac7c>] process_one_work+0x16c/0x350
[<ffffffff8107d84a>] worker_thread+0x17a/0x410
[<ffffffff81081b76>] kthread+0x96/0xa0
[<ffffffff81464944>] kernel_thread_helper+0x4/0x10
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: Pawel Baldysiak <pawel.baldysiak@intel.com>
Reviewed-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
No locks should be held when calling scsi_adjust_queue_depth
so drop the lock in slave_configure prior to calling it.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
System crashes, in initiator mode operation, with
qla2xxx_copy_atioqueues() in stack trace when firmware dump is
attempted.
Check for atio_q_length alone does not indicate if atio_ring is
allocated, make explicit check of atio_ring to avoid the crash.
Applicable to ISP24xx, ISP25xx, ISP81xx & ISP83xx line of HBAs.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The original patch was not covering all the adapters and firmwares.
This commit reverts 3a11711ad0.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reinitialize resource queue prior to freeing resource entries to ensure they
are not referenced. This fixes an issue with target_destoy accessing memory
after it was freed.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The abort command issued by ipr_cancel_op() is being added to the wrong
HRRQ free queue after the command returns. Fix it by using the HRRQ
pointer in the ipr command struct itself.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes a reference count bug in the SCSI tape driver which can be
reproduced with the following:
* Boot with slub_debug=FZPU, tape drive attached
* echo 1 > /sys/devices/... tape device pci path .../remove
* Wait for device removal
* echo 1 > /sys/kernel/slab/blkdev_queue/validate
* Slub debug complains about corrupted poison pattern
In commit 523e1d39 (block: make gendisk hold a reference to its queue)
add_disk() and disk_release() were modified to get/put an additional
reference on a disk queue to fix a reference counting discrepency
between bdev release and SCSI device removal. The ST driver never
calls add_disk(), so this commit introduced an extra kref put when the
ST driver frees its struct gendisk.
Attempts were made to fix this bug at the block level [1] but later
abandoned due to floppy driver issues [2].
[1] https://lkml.org/lkml/2012/8/27/354
[2] https://lkml.org/lkml/2012/9/22/113
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In fact the disc_resp buffer will be overwrite by smp response, so we never
found this typo, correct it by using the right one.
Signed-off-by: John Gong <john_gong@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Loading ipr modules failed(-22) with msi-x enabled adapter. In ipr_test_msi(),
We need to pass the first vector of msix vectors instead of using pdev->irq
to request_irq() when adapter enables msix feature.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The libfc discovery layer is being initialized in the
'create' paths for both legacy libfcoe module parameters
and fcoe_sysfs control interfaces. The problem is that
for VN2VN mode the discovery layer is initialized as if
it were in 'fabric' mode and it is not re-configured when
the mode is changed to 'vn2vn'.
This patch splits out code that needs to be initialized
once and code that can, and should be, re-configured when
the mode changes. Additionally this patch makes that change
so that the discovery layer can be reconfigured to the
libfcoe implementation when in 'vn2vn' mode.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Split discovery initialization in code that is setup once (fcoe_disc_init)
and code that can be re-configured (fcoe_disc_config).
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Currently libfcoe is doing some libfc discovery layer initialization outside of
libfc. This patch moves this code into libfc and sets up a split in discovery
(one time) initialization code and (re-configurable) settings that will come in
the next patch.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
The fcoemon userspace daemon is searching for the a hostX
under the the /sys/bus/fcoe/devices/ctlrX/ entries. When
interfaces created using fcoe_sysfs and fcoe.ko this linkage
is setup correctly, but bnx2fc is not doing the same thing
and therefore fcoemon does not create the fcoe interface
for bnx2fc.
This patch sets up the correct linkage for bnx2fc such that
fcoemon will work correctly with fcoe_sysfs and bnx2fc.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
USB uses the .find_bridge() callback from struct acpi_bus_type
incorrectly, because as a result of the way it is used by USB every
device in the system that doesn't have a bus type or parent is
passed to usb_acpi_find_device() for inspection.
What USB actually needs, though, is to call usb_acpi_find_device()
for USB ports that don't have a bus type defined, but have
usb_port_device_type as their device type, as well as for USB
devices.
To fix that replace the struct bus_type pointer in struct
acpi_bus_type used for matching devices to specific subsystems
with a .match() callback to be used for this purpose and update
the users of struct acpi_bus_type, including USB, accordingly.
Define the .match() callback routine for USB, usb_acpi_bus_match(),
in such a way that it will cover both USB devices and USB ports
and remove the now redundant .find_bridge() callback pointer from
usb_acpi_bus.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
This is an assorted set of stragglers into the merge window with driver
updates for qla2xxx, megaraid_sas, storvsc and ufs. It also includes pulls of
the uapi tree (all the remaining SCSI pieces) and the fcoe tree (updates to
fcoe and libfc)
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRMHJHAAoJEDeqqVYsXL0M9tAH/2YG3TCfy0RFAejGgLfX9OGH
6eFe71m7Z8nfIEneAnm5BuKjCx3QFRp5UFjJZdFHLP1Qv0TbpKs4FnZyeSGTxLQp
S1fZc5sTWmsb5qYxLaukKopC6sFx+hNI2dvB+rgKcd+nWy1RzG7lGqbS4CRNE76q
UNByqlfqJxn5cfQw7dg2zOUKlGaGL2jSyFf0QFXR2IZzO33PeyBPfKDFeJC6b+oc
XTy9MK9V5u6ne3XimDTU2hP4lPAsZaJtcqsv1Gvv2y+BHalQiPqfL6bZMvN3Zbfq
hfT+i2xnYy85858gxtyIhzHwU14zF7I0HEWiVpddsF9NDK7iNKvK8aWHaTs7qis=
=hvGQ
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is an assorted set of stragglers into the merge window with
driver updates for qla2xxx, megaraid_sas, storvsc and ufs.
It also includes pulls of the uapi tree (all the remaining SCSI
pieces) and the fcoe tree (updates to fcoe and libfc)"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (81 commits)
[SCSI] ufs: Separate PCI code into glue driver
[SCSI] ufs: Segregate PCI Specific Code
[SCSI] scsi: fix lpfc build when wmb() is defined as mb()
[SCSI] storvsc: Handle dynamic resizing of the device
[SCSI] storvsc: Restructure error handling code on command completion
[SCSI] storvsc: avoid usage of WRITE_SAME
[SCSI] aacraid: suppress two GCC warnings
[SCSI] hpsa: check for dma_mapping_error in hpsa_passthru ioctls
[SCSI] hpsa: reorganize error handling in hpsa_passthru_ioctl
[SCSI] hpsa: check for dma_mapping_error in hpsa_map_sg_chain_block
[SCSI] hpsa: Check for dma_mapping_error for all code paths using fill_cmd
[SCSI] hpsa: Check for dma_mapping_error in hpsa_map_one
[SCSI] dc395x: uninitialized variable in device_alloc()
[SCSI] Fix range check in scsi_host_dif_capable()
[SCSI] storvsc: Initialize the sglist
[SCSI] mpt2sas: Add support for OEM specific controller
[SCSI] ipr: Fix oops while resetting an ipr adapter
[SCSI] fnic: Fnic Trace Utility
[SCSI] fnic: New debug flags and debug log messages
[SCSI] fnic: fnic driver may hit BUG_ON on device reset
...
he patch set is mostly driver updates (bnx2fc, ipr, lpfc, qla4) and a few bug
fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRJ0oJAAoJEDeqqVYsXL0MVVoH/A8xFiLkdCXaFkhYMlGRrDox
wgK/RwWekDOtVS2poPhDGKRfXaUn4uA3iOJig8HC5lD8NS65DElCpCWM+/DhitXt
Ky4ukgXSQ09IQtWraGqr//MC/YqM8iimWnGgXSouLPJ7a3AqYVIYCg9CEkGJX/mD
i09aE8uUyNd3Wp68anQ2w0RCH/7/InLL348WFmQ1eWxYyFJnLYGRkASbkuHxPjgU
H4QmINFlI4kBMWdHkVinh0w7cjcmUOAU+KyAZ75aelQ6dZ2aJioKn3BS7D6gF9jv
jJpJMIj8LzpAnfR3Z5ijkkcVG7E0ht+Dtr6kmAPZQJnkc/GdQvvgEg+F9aIpxoU=
=oDz4
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"The patch set is mostly driver updates (bnx2fc, ipr, lpfc, qla4) and a
few bug fixes"
Pull delayed because google hates James, and sneakily considers his pull
requests spam. Why, google, why?
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (60 commits)
[SCSI] aacraid: 1024 max outstanding command support for Series 7 and above
[SCSI] bnx2fc: adjust duplicate test
[SCSI] qla4xxx: Update driver version to 5.03.00-k4
[SCSI] qla4xxx: Fix return code for qla4xxx_session_get_param.
[SCSI] qla4xxx: wait for boot target login response during probe.
[SCSI] qla4xxx: Added support for force firmware dump
[SCSI] qla4xxx: Re-register IRQ handler while retrying initialize of adapter
[SCSI] qla4xxx: Throttle active IOCBs to firmware limits
[SCSI] qla4xxx: Remove unnecessary code from qla4xxx_init_local_data
[SCSI] qla4xxx: Quiesce driver activities while loopback
[SCSI] qla4xxx: Rename MBOX_ASTS_IDC_NOTIFY to MBOX_ASTS_IDC_REQUEST_NOTIFICATION
[SCSI] qla4xxx: Add spurious interrupt messages under debug level 2
[SCSI] cxgb4i: Remove the scsi host device when removing device
[SCSI] bfa: fix strncpy() limiter in bfad_start_ops()
[SCSI] qla4xxx: Update driver version to 5.03.00-k3
[SCSI] qla4xxx: Correct the validation to check in get_sys_info mailbox
[SCSI] qla4xxx: Pass correct function param to qla4_8xxx_rd_direct
[SCSI] lpfc 8.3.37: Update lpfc version for 8.3.37 driver release
[SCSI] lpfc 8.3.37: Fixed infinite loop in lpfc_sli4_fcf_rr_next_index_get.
[SCSI] lpfc 8.3.37: Fixed crash due to SLI Port invalid resource count
...
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: James Smart <james.smart@emulex.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Krishna C Gudipati <kgudipat@brocade.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
