This reverts commits 9a036b93a3 ("x86/signal/64: Remove 'fs' and 'gs'
from sigcontext") and c6f2062935 ("x86/signal/64: Fix SS handling for
signals delivered to 64-bit programs").
They were cleanups, but they break dosemu by changing the signal return
behavior (and removing 'fs' and 'gs' from the sigcontext struct - while
not actually changing any behavior - causes build problems).
Reported-and-tested-by: Stas Sergeev <stsp@list.ru>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) Workaround hw bug when acquiring PCI bos ownership of iwlwifi
devices, from Emmanuel Grumbach.
2) Falling back to vmalloc in conntrack should not emit a warning, from
Pablo Neira Ayuso.
3) Fix NULL deref when rtlwifi driver is used as an AP, from Luis
Felipe Dominguez Vega.
4) Rocker doesn't free netdev on device removal, from Ido Schimmel.
5) UDP multicast early sock demux has route handling races, from Eric
Dumazet.
6) Fix L4 checksum handling in openvswitch, from Glenn Griffin.
7) Fix use-after-free in skb_set_peeked, from Herbert Xu.
8) Don't advertize NETIF_F_FRAGLIST in virtio_net driver, this can lead
to fraglists longer than the driver can support. From Jason Wang.
9) Fix mlx5 on non-4k-pagesize systems, from Carol L Soto.
10) Fix interrupt storm in bna driver, from Ivan Vecera.
11) Don't propagate -EBUSY from netlink_insert(), from Daniel Borkmann.
12) Fix inet request sock leak, from Eric Dumazet.
13) Fix TX interrupt masking and marking in TX descriptors of fs_enet
driver, from LEROY Christophe.
14) Get rid of rule optimizer in gianfar driver, it's buggy and unlikely
to get fixed any time soon. From Jakub Kicinski
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
cosa: missing error code on failure in probe()
gianfar: remove faulty filer optimizer
gianfar: correct list membership accounting
gianfar: correct filer table writing
bonding: Gratuitous ARP gets dropped when first slave added
net: dsa: Do not override PHY interface if already configured
net: fs_enet: mask interrupts for TX partial frames.
net: fs_enet: explicitly remove I flag on TX partial frames
inet: fix possible request socket leak
inet: fix races with reqsk timers
mkiss: Fix error handling in mkiss_open()
bnx2x: Free NVRAM lock at end of each page
bnx2x: Prevent null pointer dereference on SKB release
cxgb4: missing curly braces in t4_setup_debugfs()
net-timestamp: Update skb_complete_tx_timestamp comment
ipv6: don't reject link-local nexthop on other interface
netlink: make sure -EBUSY won't escape from netlink_insert
bna: fix interrupts storm caused by erroneous packets
net: mvpp2: replace TX coalescing interrupts with hrtimer
net: mvpp2: enable proper per-CPU TX buffers unmapping
...
missed during the conversion a couple of years ago.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVzBnmAAoJEBLB8Bhh3lVKCdwP+welT0JP1MkElR0KPTyrfi98
xn1NSO6WfEuXeYQWCUKImsEpMGMulIzc2MW/+KD2aYwnT+iUG2S/etOC6nCEzbq4
vx0CTKyNAMz55YHZqWXXCUh563WvJczE56J5FQK2tTqv4jaWUKFxPI6tZ+zvDfoR
phLHRAwaHcaSeD7eaFznNsggF5lEJthzzM7jF2d+g2TO6nbVRZWVo4lhKmV7wOj8
+/fkPzUFrY+pRvE3Ceop10hT1UY6t6mi3xQFPcU3f+gY9DIr8VFZF1soyLnKMSqi
SBCiiHzVUhLpSew5JBtvjxL3vSu9vJAFXwBFY4FCkwzIdzyrwNCnH3roDmCGuSuu
Kj9KHh6BIpBCI5njgvtsx9Ou6XNPwEtZojd2VUfh3BIkZEtXH1+UjIgoOaGuhg4A
H5kzdEs/w2sfXX5MAJwh5F97qKXJbJ656IgdE7ZDNIhUN6EQLWet37mLkXADtEr1
0yn//KsidWAk4FqYMSBs0RAHYd7vipm6GodLOTxwejpMWrp1nUS5KhRaSu/0k1u0
gwEmR1BtwO+mv0o0tg9YGYtmYdZ3X+cYrozIFF1M3RzFd1FzqgEIIpQRzQ66B3Wm
zPnfvr8EXscQIcxgF/AwRGrf8Yc0mvN3FMctQkEfV9rNEsCwNJdv2xSu+lOm3S/Y
qhbkLxg35KonH1v04w0f
=AM3b
-----END PGP SIGNATURE-----
Merge tag 'edac_fix_for_4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC fix from Borislav Petkov:
"A ppc4xx_edac fix for accessing ->csrows properly. This driver was
missed during the conversion a couple of years ago"
* tag 'edac_fix_for_4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, ppc4xx: Access mci->csrows array elements properly
Currently mdio bindings are defined in keystone.dtsi and this results
in incorrect unit address for the node on K2E and K2L SoCs. Fix this
by moving them to SoC specific DTS file.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Currently the MDIO clock is pointing to clkpa instead of clkcpgmac.
MDIO is part of the ethss and the clock should be clkcpgmac.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The likelihood of getting a large number of panel drivers from different
vendors is quite high. Add a prefix to the two existing Samsung panel
drivers to set a guideline for future patch submissions. Using vendor
prefixes consistently should allow a cleaner organization of the tree.
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nSeK
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.2/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fix a NULL pointer exception for omap GPMC bus code if probe fails.
* tag 'omap-for-v4.2/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
memory: omap-gpmc: Don't try to save uninitialized GPMC context
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that the PTN3460 driver has been rewritten as a proper I2C driver
and there is infrastructure to hook up the bridge with a DRM device, it
is no longer necessary to have this dependency to ensure the correct
build mode.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR1 introduced on Tegra210 supports HDMI 2.0 and DisplayPort. Add
HDMI support and name the debugfs node after the type of SOR. The SOR
introduced with Tegra124 is known simply as "sor", whereas the
additional SOR found on Tegra210 is known as "sor1".
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR found on Tegra210 is very similar to the version found on
Tegra124, except that it no longer supports LVDS.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move all code into the new canonical ->disable() and ->enable() helper
callbacks so that they play extra nice with atomic DPMS.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to restore DPMS with atomic mode-setting, move all code from
the ->mode_set() callback into ->enable(). At the same time, rename the
->prepare() callback to ->disable() to use the names preferred by atomic
mode-setting. This simplifies the calling sequence and will allow DPMS
to use runtime PM in subsequent patches.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to restore DPMS with atomic mode-setting, move all code from
the ->mode_set() callback into ->enable(). At the same time, rename the
->prepare() callback to ->disable() to use the names preferred by atomic
mode-setting. This simplifies the calling sequence and will allow DPMS
to use runtime PM in subsequent patches.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to restore DPMS with atomic mode-setting, move all code from
the ->mode_set() callback into ->enable(). At the same time, rename the
->prepare() callback to ->disable() to use the names preferred by atomic
mode-setting. This simplifies the calling sequence and will allow DPMS
code to use runtime PM in subsequent patches.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to restore DPMS with atomic mode-setting, move all code from
the ->mode_set() callback into ->enable(). At the same time, rename the
->prepare() callback to ->disable() to use the names preferred by atomic
mode-setting. This simplifies the calling sequence and will allow DPMS
code to use runtime PM in subsequent patches.
While at it, remove the enabled field that hasn't been used since the
demidlayering of the output drivers done in preparation for the atomic
mode-setting conversion.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of duplicating most of the code to set up a debugfs file, use
the existing DRM core debugfs infrastructure instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The head state registers are per head, so they must be properly indexed.
This has worked fine so far because all boards with eDP use it as the
primary output, so it is very likely to end up attached to head 0.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The data structure is always only read, never written, and can hence be
referred to by a const pointer.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When tearing down debugfs support, make sure to reset the fields to NULL
in the correct order, otherwise the debugfs root will not be properly
removed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM minor is needed to teardown debugfs, so it needs to be tracked
to prevent a crash on driver removal.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When probing the SOR device fails, output proper error messages to help
diagnose the cause of the failure.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The TRM lists indexed registers without an underscore to separate name
from index. Use that convention in the driver for consistency.
While at it, rename some of the field names to the names used in the
TRM.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the DPAUX isn't attached to an SOR the interrupts are not useful.
This also prevents a race that could potentially cause a crash on driver
removal.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DPAUX code paths already configure the pads in AUX mode, but there
is no way to reconfigure them in I2C mode for HDMI (the DPAUX module is
unused in that case). Enabling the pads in I2C mode by default is the
quickest way to support HDMI. Eventually this may need an explicit call
in the user drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When probing the dpaux device fails, output proper error messages to
help diagnose the cause of the failure.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI host controller hasn't changed from Tegra132 to Tegra210, but
different characterization parameters may be required.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI host controller hasn't changed from Tegra124 to Tegra132, but
different characterization parameters may be required.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI host controller hasn't changed from Tegra114 to Tegra124, but
different characterization parameters may be required.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In video modes without sync pulses, the horizontal back-porch needs to
include the horizontal sync width.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The call to platform_driver_register() will already set up the .owner
field, so there's no need to do it explicitly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The horizontal pulse enable bits are named H_PULSE{0,1,2}_ENABLE in the
TRM. Modify the driver to use the same naming for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Record interrupt statistics, such as the number of frames and VBLANKs
received and the number of FIFO underflow and overflows.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Request a syncpoint for display prior to registering the host1x client.
This will ensure that the syncpoint will be acquired when the KMS driver
initializes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Upon driver load, reset the VBLANK machinery to off to reflect the
hardware state. Since the ->reset() callback is called from the initial
drm_mode_config_reset() call, move the latter after the VBLANK machinery
initialization by drm_vblank_init().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Keep track of the number of users of DSI and CSI pads and power down the
regulators that supply the bricks when all users are gone.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some changes are needed to the configuration settings for some lanes. In
addition, the clock lanes for the CSI pads can no longer be calibrated.
Signed-off-by: Thierry Reding <treding@nvidia.com>
While Tegra132 has the same pads as Tegra124, some configuration values
need to be programmed slightly differently.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Before starting a new calibration cycle, make sure to clear the current
status by writing a 1 to the various "calibration done" bits.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use more consistent names for the clock lane configuration registers and
fix the offset of the upper clock lane configuration register for the
first DSI pad.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Parameterize more of the register programming to accomodate for changes
required by future SoC generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
- Fix i.MX6 PCIe interrupt routing which gets missed from stacked IRQ
domain conversion. The PCIe wakeup support is currently broken
because of this.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVyL2qAAoJEFBXWFqHsHzOGHgH/jgyCg6QVHgxgAoCjySZUbtT
OwYFKxR3697GGVyUMa0r47TQxL5PusCUzJrNJTg6AhhgatKsGfiB45NRZy5bt8k5
8M4tShc1n/fV7N2T1h1QbpXZiPhofhFtMq9Yq1lPDrQvOLOymWWZhGwBqbFy0bJT
4IzqUS7uTE/pvrbFf+iqlwxshSzbbMOOHPqAavyinAKQU5S93v7D4iKJ0q2EmTqh
hypAL1lZ0/BwBKWSeVVzJoVUFHZFmSzhlbE6ZzcY7S/4Dn2oTwiZQPb+eWj8kQHn
CALj6KFSnhQ4XKfcBFTH1Z/apSWs6SDWDOig2jzQ/X+JFo9ahnh4fp91NqLML+o=
=lUqF
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 4.2, 3rd round:
- Fix i.MX6 PCIe interrupt routing which gets missed from stacked IRQ
domain conversion. The PCIe wakeup support is currently broken
because of this.
* tag 'imx-fixes-4.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx6: correct i.MX6 PCIe interrupt routing
Signed-off-by: Olof Johansson <olof@lixom.net>
