Bump the min wl18xx fw version to 8.8.0.0.13
This fw is not backward compatible with older
firmware (due to api changes), so use bump
the firmware name as well.
Some modifications were done to the driver-fw api
in order to support multiple APs.
Additionally, some of the consts (such as max stations,
max links and max RX BA sessions) were changed.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Each hw supports a different iface combinations.
Define the supported combinations in each driver,
and save it in wl->iface_combinations.
Since each driver defines its own combinations now,
it can also define its max supported channels, so
we no longer need to save and set it explicitly
in wlcore.
Update wl18xx interface combinations to allow
multiple APs.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Each hw supports a different max stations (connected to the
same ap). add a new wl->max_ap_stations and use it instead
of the current common AP_MAX_STATIONS.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upcoming fw versions will have different max links support
(according to the hw). Get ready for it by configuring
wl->num_links per-hw, instead of using the const WL12XX_MAX_LINKS.
However, continue using WLCORE_MAX_LINKS in order to simplify
structs declarations (we use it in multiple bitmaps, and converting
them to dynamic arrays is just cumbersome).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of splitting the fw_status into 2 and using some
complex calculations, read the fw status and let each low-level
driver (wl12xx/wl18xx) convert it into a common struct.
This is required for the upcoming fw api changes, which
break the current logic anyway.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems the wl18xx FW sometimes sends spurious changes on the PSM state
of the broadcast HLID. This causes us to search for a station on a
non-peer link and fail, causing warnings in our log.
Prevent the driver from considering PSM changes for any non-peer HLIDs.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the chip is in ELP mode read/write to FW is invalid and may cause
the lower layers to get stuck. The reads/writes concerning ELP wakeup
are the exception here and are checked for. In addition to blocking the
IO, produce a warning.
Signed-off-by: Barak Bercovitz <barak@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes a tx_flush during suspend fails, but the FW manages to flush
out the packets during the time when the host is supsended. Cancel
the Tx-watchdog on suspend to not cause a spurious recovery on resume
for that case. Set a flag to reinit the watchdog on the first Tx after
resume, so we'll still recover if the FW is not empty and there's
indeed a problem.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zero rx_filter_enabled array after recovery to avoid
cases were the driver will keep trying to clear a
filter which is not configured in FW.
Such case will cause consecutive recoveries due to
command execution failures.
While on it, convert rx_filter_enabled to bitmap,
to save some memory and make sparse happy (it
doesn't like sizeof(bool array)).
Signed-off-by: Nadim Zubidat <nadimz@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver ignores BSS_CHANGED_TXPOWER changes.
Fix this by calling ACX_TX_POWER when appropriate.
Signed-off-by: Alex Gal <a.gal@motsai.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add nvs file name to module firmware list
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware doesn't support per packet encryption selection, so disable hw
encryption support completely while a monitor interface is present to support
injection of packets (which shouldn't get encrypted by hw).
To enforce the changed hw encryption support force a disassociation on
non-monitor interfaces.
For disassociation a workaround using hw connection monitor is employed,
which temporary enables hw connection manager flag.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the retry limit to 0 and disable the ACK policy for injected packets.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If necessary enable the tx path in monitor mode for packet injection using
the JOIN command with BSS_TYPE_STA_BSS and zero BSSID.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the ENABLE_RX command for channel switching when no interface is present
(monitor mode only).
The advantage of ENABLE_RX is that it leaves the tx data path disabled in
firmware, whereas the usual JOIN command seems to transmit some frames at
firmware level.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Force power saving off while monitor interface is present.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Port multicast address filtering from wl1271 driver.
It sets up the hardware multicast address filter in configure_filter() with
addresses supplied through prepare_multicast().
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable hardware encryption (DF_ENCRYPTION_DISABLE) and decryption
(DF_SNIFF_MODE_ENABLE) via wl1251_acx_feature_cfg while monitor interface is
present.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split up data path initialisation into RX and TX data path initialisation
functions. This change is required for channel switching in monitor mode.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update hardware ARP filter configuration on BSS_CHANGED_ARP_FILTER
notification from mac80211.
Ported from wl1271 driver.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Port of the power save entry retry code from wl1251 driver version included
in the Maemo Fremantle kernel.
This tries to enable power save mode up to 3 times before failing.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With a dissasociated card I often encoutered very long scan delays.
My guess is that it has something to do with the cards DTIM handling and
another firmware bug mentioned in the TI WLAN driver, which is described as
the card may never end scanning if the channel is overloaded because it
can't send probe requests. I think the firmware somehow also tries to
receive DTIM messages when the BSSID is not set. Therefore most of the time
it waits for DTIM messages and can't do scanning work.
Anyway we can workaround this misbehaviour by setting the HIGH_PRIORITY
bit for scans in disassociated state.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This value is no longer used by mac80211, and practically no
driver ever set it to a correct value anyway, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use possibly more efficient ether_addr_equal or
ether_addr_equal_unaligned instead of memcmp.
Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the original code used goto out if kzalloc fails,but the out include kfree,
so return -ENOMEM if kzalloc fails.
Signed-off-by: Jing Wang <windsdaemon@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These two flags are used for the same purpose, just
combine them into a no-ir flag to annotate no initiating
radiation is allowed.
Old userspace sending either flag will have it treated as
the no-ir flag. To be considerate to older userspace we
also send both the no-ir flag and the old no-ibss flags.
Newer userspace will have to be aware of older kernels.
Update all places in the tree using these flags with the
following semantic patch:
@@
@@
-NL80211_RRF_PASSIVE_SCAN
+NL80211_RRF_NO_IR
@@
@@
-NL80211_RRF_NO_IBSS
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_PASSIVE_SCAN
+IEEE80211_CHAN_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IBSS
+IEEE80211_CHAN_NO_IR
@@
@@
-NL80211_RRF_NO_IR | NL80211_RRF_NO_IR
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IR | IEEE80211_CHAN_NO_IR
+IEEE80211_CHAN_NO_IR
@@
@@
-(NL80211_RRF_NO_IR)
+NL80211_RRF_NO_IR
@@
@@
-(IEEE80211_CHAN_NO_IR)
+IEEE80211_CHAN_NO_IR
Along with some hand-optimisations in documentation, to
remove duplicates and to fix some indentation.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[do all the driver updates in one go]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to reconfigure the correct reg domain on
recovery, we have to save the current configuration
before clearing it (wl->reg_ch_conf_pending is
considered before configuring a new regdomain).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
wlcore configures different dwell times according to number
of active interfaces (in order to prevent hurting VO during
scan).
However, determining active vif only according to
bss_conf->idle is not explicit enough, and might result
in non-started vifs being counted as started as well
(e.g. unassociated sta during sta).
Fix it by checking for explicit conditions according
to the vif type.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Make sure the FW is awake when entering recovery. This is useful for
reading the FW panic log and also some FW registers giving us crash
report stats.
We must do this before interrupts are disabled since we rely on an
interrupt to complete the wakeup.
If the wakeup fails, continue recovery normally. All read/writes will be
blocked and won't do any harm.
Signed-off-by: Barak Bercovitz <barak@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
The FW panic log is read during recovery work.
It has to be stopped properly before reading. otherwise,
inconsistent data might be read which cause the driver
to freeze.
__wlcore_cmd_send has to work for the special case of
CMD_STOP_FWLOGGER, while in recovery, in order to stop
the fw log before it is read.
Signed-off-by: Barak Bercovitz <barak@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
FW memory block size and FW log end marker parameters
are added to wl structure and are initialized per
chip architecture.
convert_hwaddr hw operation is added to convert chip
dependent FW internal address.
Copy from FW log is also simplified to copy the entire
memory block as FW logger utility is repsponsible
for parsing of FW log content.
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
update the fw logger mode to continuous, and output to dbgpins (uart).
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
number of fwlog mem_blocks can be configured using module param.
this is a fw debug feature: in case a large fw log data is busrted during
a short period of time, the memory get filled and data is lost.
this allows us to dynamicly set the fw log mem_block usage, although
configuring more mem_block for logger comes at the expense of TP.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Change interrogate command prototype to have command size
and returned buffer length.
This fixes the issue when command parameters are needed to
be passed to FW in addition to acx header as in the case with
get RSSI command, where role_id has to be passed.
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Add new ap_event_mask field, to indicate events that
should be unmasked only when there's an ap interface.
This is done in order to avoid spurious wakeups
when we don't care about the incoming event anyway.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Print current active channel/s and a role type for
that channel in the driver_state debugfs.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Driver default config is aligned with phy default parameters.
Now that RDL1_3 has 2 antennas defined by default we need to explicitly
define ht.mode to HT_MODE_WIDE to have SISO40 as default.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
TI firmwares are located under ti-connectivity
directory. Update path to make sure driver can
find and load firmware blob.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This keeps the kernel happy when using edge-irqs and requesting a
threaded irq.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Extract and print info for the new RDL 5, 6, 7 and 8.
Replace const struct with function which translates
the RDL number to string.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Barak Bercovitz <barak@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
In addition to existing WCS PLL configuration add and enable
also the coex PLL during init phase. This fixes boot failures
due to silicon latchup in high temperature environment (>85c).
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Nadim Zubidat <nadimz@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Channels 52-64 were mapped incorrectly.
Refactor and document wlcore_get_reg_conf_ch_idx() in
order to make it clear what's going on there.
While on it, fix the return value check to consider
0 as a valid return value as well (indicates channel 1).
Reported-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
wlvif could be passed as NULL from the wlcore_tx_work_locked()
to the wl1271_prepare_tx_frame() and to wl1271_skb_queue_head()
functions. This may lead to a Kernel panic, fix this by
validating that wlvif != NULL.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Remove scan debug dumps which are rarely used.
Make scan debug prints more clear and short.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
We need some stuff done on idle change, most notably we have to stop
sched-scanning. Take care of this by reintroducing idle handling.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
We now disable elp sleep during plt mode to allow normal operation of
plt tools such as calibrator.
Having elp_sleep enabled during plt mode is actually not required and
in fact it disrupt plt operations such as rx statistics etc.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Under this mode the chip is powered on including sdio
but no FW is downloaded and run, interrupts are not enabled, etc...
This mode is intended to allow RTTT to bridge sdio as a transport
to the chip.
Driver only provides sdio access using the dev_mem debugfs file.
Some fixes done to the code that ensures that PLT mode and normal
driver power mode (ifconfig/add_interface) are mutually excluded.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Start a ROC on the AP channel beforing sending the authentication reply
to a connecting STA. This ROC is held up to 1 second via a timer. If the
station is authorized and added by mac80211, the ROC is extended until
the station is fully authorized.
We make sure not to ROC twice when several stations are connecting in
parallel and to only release the ROC when both the pending-reply timer
and the STA-state callbacks do not require it.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
mac80211 currently sets WIPHY_FLAG_SUPPORTS_SCHED_SCAN based on whether
the start_sched_scan operation is supported or not, but that will not
be correct for all drivers, we're adding scheduled scan to the iwlmvm
driver but it depends on firmware support.
Therefore, move setting WIPHY_FLAG_SUPPORTS_SCHED_SCAN into the drivers
so that they can control it regardless of implementing the operation.
This currently only affects the TI drivers since they're the only ones
implementing scheduled scan (in a mac80211 driver.)
Acked-by: Luciano Coelho <luca@coelho.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the wdev from cfg80211 on to the driver as the vif
if given and it's valid for the driver.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently packet patterns and it's enum/structures are used only
for WoWLAN feature. As we intend to reuse them for new feature
packet coalesce, they are renamed in this patch.
Older names are kept for backward compatibility purpose.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a9 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
Make the commenting style consistent with networking block comment
style as suggested by checkpatch.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Removing some boilerplate by using module_spi_driver instead of calling
register and unregister in the otherwise empty init/exit functions
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The fw_status wasn't zeroed during allocation, resulting
in uninitialized var usage, and finally causing AP
traffic stop after recovery.
The wrong value in fw_status_2->counters.tx_lnk_free_pkts
led to a bad lnk->allocated_pkts calculation in
wlcore_fw_status(), causing wl18xx_lnk_low_prio() to return
FALSE (lnk->allocated_pkts > thold).
This eventually blocked the link in wlcore_tx_work_locked(),
as wl1271_skb_dequeue() continuously returned NULL.
Fix it by zeroing wl->fw_status_1/2 during allocation.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Otherwise, if the work is pending, we might get
a bad dereference after the interface is removed.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When associating to an AP with WEP set the
default key upon association by implementing
the set_deafult_key_idx op.
Fixes auto-arp sent with wrong key_idx bug.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In some R&D chips, the device may be left untrimmed and with the MAC
address missing from fuse ROM. In order to support those devices,
apply a random locally administered MAC address instead.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The current code configures the peer caps only on BSS_CHANGED_HT
notification. However, we have to configure the peer caps
(and rates) even when HT is not enabled. Otherwise, the fw
continues working with low rates.
Configure the peer caps when sta_exists is true (i.e. when
we extracted the sta rates, e.g. on association).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Instead of doing all the sysfs file handling in the main file, move it
to a new sysfs source file to reduce the amount of code in a single
file.
Signed-off-by: Luciano Coelho <coelho@ti.com>
In PG2.0 there is an issue where PHY's FDSP Code RAM sometimes gets
corrupted when exiting from ELP mode. This issue is related to FDSP
Code RAM clock implementation.
PG2.1 introduces a HW fix for this issue that requires the driver to
change the FDSP Code Ram clock settings (mux it to ATGP clock instead
of its own clock).
This workaround uses PHY_FPGA_SPARE_1 register and is relevant to WL8
PG2.1 devices.
The fix is also backward compatible with older PG2.0 devices where the
register PHY_FPGA_SPARE_1 is not used and not connected.
The fix is done in the wl18xx_pre_upload function (must be performed
before uploading the FW code) and includes the following steps:
1. Disable FDSP clock
2. Set ATPG clock toward FDSP Code RAM rather than its own clock.
3. Re-enable FDSP clock
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Due to a typo, the current code copies only sizeof(cmd->channels_2)
bytes, which is smaller than the correct sizeof(cmd->channels_5)
size, resulting in a partial scan (some channels are skipped).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The minimum firmware version required for singlerole after recent
driver changes is 6/7.3.10.0.133.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a typo in commit 8675f9 (wlcore/wl12xx/wl18xx: verify
multi-role and single-role fw versions), which was causing the
multirole firmware for wl127x (WiLink6) to be rejected. The actual
minimum version needed for wl127x multirole is 6.5.7.0.42.
Reported-by: Levi Pearson <levipearson@gmail.com>
Reported-by: Michael Scott <hashcode0f@gmail.com>
Cc: stable@kernel.org # 3.9+
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to take up the space for devices that don't
support WoWLAN, and most drivers can even make the support
data static const (except where it's modified at runtime.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for the secondary channel offset IE in channel
switch announcements. This is necessary for proper handling
of CSA on HT access points.
For this to work it is also necessary to convert everything
here to use chandef structs instead of just channels. The
driver updates aren't really correct though. In particular,
the TI wl18xx driver update can't possibly be right since
it just ignores the new channel width for lack of firmware
API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers that don't use chanctxes cannot perform VHT association because
they still use a "backward compatibility" pair of {ieee80211_channel,
nl80211_channel_type} in ieee80211_conf and ieee80211_local.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
[fix kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Spin locks and completions are expensive in hard IRQ context and cause
problems with RT kernels. In RT kernels, both spin locks and
completions can schedule(), so we can't use them in hard irq context.
Move handling code into the irq thread function to avoid that.
Reported-by: Gregoire Gentil <gregoire@alwaysinnovating.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We were printing out all the hex dumps regardless of whether dynamic
debugging was enabled or not. Now that print_hex_dump_debug() has
been implemented, we can use that instead.
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Don't ignore dummy packets when our queues are empty. This causes dummy
packets never to be sent when traffic is not suspended by FW thresholds,
which happens only in high Tx throughput situations. This may hurt Rx
performance.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wlcore state was checked without the mutex being taken. This leads
to WARN_ONs sometimes if a notification arrives when the driver
is on, but the mutex is only taken after it is off. This usually
happens if stopping the driver while connected to a network.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Save the sequence number of the broadcast AP link in the wlvif. For each
connected station, save the sequence number in the drv_priv part of
ieee80211_sta. Use the saved numbers on recovery/resume, with the
obligatory increment on recovery.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Dont use free_sta() on AP global links. It would fail an internal check
within the function and various structures within the link struct would
not be reset.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Print board type, PG with metal and ROM versions.
This might help debugging HW related issues.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
For STA we report beacon loss to higher levels so that wpa_s
can attempt to roam without disconnecting. In case of P2P CLI
we don't want to attempt roaming and instead disconnect immediately
upon beacon loss.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
On !CONFIG_SMP builds spin_is_locked always returns 0. Assert the
locking using assert_spin_locked, which is written to behave correctly
in all cases.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
report the average beacon rssi which is calculated
by firmware for roaming statistics instead of the
last rx packet rssi. this results a more accurate
rssi reporting
Signed-off-by: Nadim Zubidat <nadimz@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Accumulate the total number of sent packets per-link to find out how far
the encryption sequence number has progressed. Use this number as the
initial security sequence number after recovery.
This consolidates security sequence handling for both chip families, as
we no longer have to rely on 12xx specific Tx completion.
A fortunate side effect of this is correct management of seq numbers for
AP roles and multi-role scenarios.
When a link is removed we save the last seq number on a persistent part
of the wlvif. This helps the data survive through recoveries/suspends,
which also entail changes in the hlid of the link.
This functionality is STA only currently.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The HLID of a STA can change, particularly during recovery. Don't cache
the HLID before it was potentially allocated.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
commit 144614f3eebd7d only allowed a single active link when
turning on the optimization, ignoring the fact that an AP has two
additional global links.
Use 3 links as an indication for a single active link. Use the
FW PSM bits to verify the extra active link belongs to the AP role.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Maximum number of supported RX BA sessions depends on chip type.
wl18xx supports 5 RX BA sessions while wl12xx supports 3.
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
It is requiered to enter sleep mode with smaller delay in forced PS mode.
This fixes issue of testing force PS mode during VoIP traffic where packets
are sent every 20ms. Chip never enters ps mode with default 30 ms delay
in such test.
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
There are a number of situations in which mac80211 only
really needs to flush queues for one virtual interface,
and in fact during this frames might be transmitted on
other virtual interfaces. Calculate and pass a queue
bitmap to the driver so it knows which queues to flush.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices can handle remain on channel requests differently
based on the request type/priority. Add support to
differentiate between different ROC types, i.e., indicate that
the ROC is required for sending managment frames.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even in failed case of pm_runtime_get_sync, the usage_count
is incremented. In order to keep the usage_count with correct
value and runtime power management to behave correctly, call
pm_runtime_put(_sync) in such case.
Signed-off-by Liu Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Li Fei <fei.li@intel.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Pull networking update from David Miller:
1) Checkpoint/restarted TCP sockets now can properly propagate the TCP
timestamp offset. From Andrey Vagin.
2) VMWARE VM VSOCK layer, from Andy King.
3) Much improved support for virtual functions and SR-IOV in bnx2x,
from Ariel ELior.
4) All protocols on ipv4 and ipv6 are now network namespace aware, and
all the compatability checks for initial-namespace-only protocols is
removed. Thanks to Tom Parkin for helping deal with the last major
holdout, L2TP.
5) IPV6 support in netpoll and network namespace support in pktgen,
from Cong Wang.
6) Multiple Registration Protocol (MRP) and Multiple VLAN Registration
Protocol (MVRP) support, from David Ward.
7) Compute packet lengths more accurately in the packet scheduler, from
Eric Dumazet.
8) Use per-task page fragment allocator in skb_append_datato_frags(),
also from Eric Dumazet.
9) Add support for connection tracking labels in netfilter, from
Florian Westphal.
10) Fix default multicast group joining on ipv6, and add anti-spoofing
checks to 6to4 and 6rd. From Hannes Frederic Sowa.
11) Make ipv4/ipv6 fragmentation memory limits more reasonable in modern
times, rearrange inet frag datastructures for better cacheline
locality, and move more operations outside of locking. From Jesper
Dangaard Brouer.
12) Instead of strict master <--> slave relationships, allow arbitrary
scenerios with "upper device lists". From Jiri Pirko.
13) Improve rate limiting accuracy in TBF and act_police, also from Jiri
Pirko.
14) Add a BPF filter netfilter match target, from Willem de Bruijn.
15) Orphan and delete a bunch of pre-historic networking drivers from
Paul Gortmaker.
16) Add TSO support for GRE tunnels, from Pravin B SHelar. Although
this still needs some minor bug fixing before it's %100 correct in
all cases.
17) Handle unresolved IPSEC states like ARP, with a resolution packet
queue. From Steffen Klassert.
18) Remove TCP Appropriate Byte Count support (ABC), from Stephen
Hemminger. This was long overdue.
19) Support SO_REUSEPORT, from Tom Herbert.
20) Allow locking a socket BPF filter, so that it cannot change after a
process drops capabilities.
21) Add VLAN filtering to bridge, from Vlad Yasevich.
22) Bring ipv6 on-par with ipv4 and do not cache neighbour entries in
the ipv6 routes, from YOSHIFUJI Hideaki.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1538 commits)
ipv6: fix race condition regarding dst->expires and dst->from.
net: fix a wrong assignment in skb_split()
ip_gre: remove an extra dst_release()
ppp: set qdisc_tx_busylock to avoid LOCKDEP splat
atl1c: restore buffer state
net: fix a build failure when !CONFIG_PROC_FS
net: ipv4: fix waring -Wunused-variable
net: proc: fix build failed when procfs is not configured
Revert "xen: netback: remove redundant xenvif_put"
net: move procfs code to net/core/net-procfs.c
qmi_wwan, cdc-ether: add ADU960S
bonding: set sysfs device_type to 'bond'
bonding: fix bond_release_all inconsistencies
b44: use netdev_alloc_skb_ip_align()
xen: netback: remove redundant xenvif_put
net: fec: Do a sanity check on the gpio number
ip_gre: propogate target device GSO capability to the tunnel device
ip_gre: allow CSUM capable devices to handle packets
bonding: Fix initialize after use for 3ad machine state spinlock
bonding: Fix race condition between bond_enslave() and bond_3ad_update_lacp_rate()
...
For VHT, many more bandwidth changes are possible. As a first
step, stop toggling the IEEE80211_HT_CAP_SUP_WIDTH_20_40 flag
in the HT capabilities and instead introduce a bandwidth field
indicating the currently usable bandwidth to transmit to the
station. Of course, make all drivers use it.
To achieve this, make ieee80211_ht_cap_ie_to_sta_ht_cap() get
the station as an argument, rather than the new capabilities,
so it can set up the new bandwidth field.
If the station is a VHT station and VHT bandwidth is in use,
also set the bandwidth accordingly.
Doing this allows us to get rid of the supports_40mhz flag as
the HT capabilities now reflect the true capability instead of
the current setting.
While at it, also fix ieee80211_ht_cap_ie_to_sta_ht_cap() to not
ignore HT cap overrides when MCS TX isn't supported (not that it
really happens...)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In commit 0d2e7a5c (wireless: Remove unnecessary alloc/OOM messages,
alloc cleanups) OOM messages after alloc were removed from the wlcore
modules.
Commit afb43e6d (wlcore: remove if_ops from platform_data)
reintroduced a couple of those. This patch removes them.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are only a few drivers that use HW scan, and
all of those don't need a non-idle transition before
starting the scan -- some don't even care about idle
at all. Remove the flag and code associated with it.
The only driver that really actually needed this is
wl1251 and it can just do it itself in the hw_scan
callback -- implement that.
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In wl18xx, we use a new ACX command in order to set the remote
supported rates, once we know it (ie. after association). The wl12xx
firmware doesn't support changing the rates after the STA is started,
so we need to use all supported rates.
Commit 530abe19 (wlcore: add ACX_PEER_CAP command) broke that by using
wlvif->rate_set when starting the STA role.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add back-off settings to the wl18xx_mac_and_phy_params. We had an
empty space where the new parameters are added, so this change doesn't
affect backwards-compatibility with older firmwares.
Update WL18XX_CONF_VERSION accordingly.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
There's no need to hide the actual error that was reported when
booting fails. For instance, on I/O error, we were returing
-EINVALID, which doesn't make sense at all.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The platform data is used not only by wlcore-based drivers, but also
by wl1251. Move it up in the directory hierarchy to reflect this.
Additionally, make it truly optional. At the moment, disabling
platform data while wl1251_sdio or wlcore_sdio are enabled doesn't
work, but it will be necessary when device tree support is
implemented.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
The platform devices can be created by both wlcore_sdio and
wlcore_spi. Theoretically, if both are connected to the same board,
there will be a conflict.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Just a small cleanup to use the pointer provided by wlcore_pdev_data
instead of using a separate pointer then copying.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We can't pass pointers from the platform data to the modules, because
with DT it cannot be done. Those pointers are not set by the board
files anyway. It's the bus modules that set them, so they can be
safely removed from the platform data without changing any board
files.
Create a new structure that the bus modules pass to wlcore. This
structure contains the if_ops pointers and a pointer to the actual
platform data.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
There is no platform-specific set_power method anymore. Power setting
is done in the bus modules (wlcore_sdio and wlcore_spi).
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
The PLT firmware used by wl12xx for calibration always has the same
version number as the single-role firmware.
Currntly the driver rejects the PLT firmware since anything that is
not single-role uses the multi-role version. Fix this by using the
single-role version for everything except multi-role.
Signed-off-by: Luciano Coelho <coelho@ti.com>
alloc failures already get standardized OOM
messages and a dump_stack.
Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Remove now unused variables.
Remove unnecessary memset after kzalloc->kcalloc.
Whitespace cleanups for these changes.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the driver, having ARP filtering for
some addresses may be possible. Remove the logic
that tracks whether ARP filter is enabled or not
and give the driver the total number of addresses
instead of the length of the list so it can make
its own decision.
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The reg_notifier()'s return value need not be checked
as it is only supposed to do post regulatory work and
that should never fail. Any behaviour to regulatory
that needs to be considered before cfg80211 does work
to a driver should be specified by using the already
existing flags, the reg_notifier() just does post
processing should it find it needs to.
Also make lbs_reg_notifier static.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[move lbs_reg_notifier to not break compile]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When TX aggregation is stopped, there are a few
different cases:
- connection with the peer was dropped
- session stop was requested locally
- session stop was requested by the peer
- connection was dropped while a session is stopping
The behaviour in these cases should be different, if
the connection is dropped then the driver should drop
all frames, otherwise the frames may continue to be
transmitted, aggregated in the case of a locally
requested session stop or unaggregated in the case of
the peer requesting session stop.
Split these different cases so that the driver can
act accordingly; however, treat local and remote stop
the same way and ask the driver to not send frames as
aggregated packets any more.
In the case of connection drop, the stop callback the
driver is otherwise supposed to call is no longer
required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to test whether a (delayed) work item in pending
before queueing, flushing or cancelling it. Most uses are unnecessary
and quite a few of them are buggy.
Remove unnecessary pending tests from wl1251. Only compile tested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Luciano Coelho <coelho@ti.com>
Cc: linux-wireless@vger.kernel.org
Some of the mmc drivers initiate DMA transfers with buffers passed from
higher layers. This means that the driver shouldn't ever pass non
DMA-able buffers, such as ones that are unaligned, allocated on the
stack or static.
Fix a couple of calls to the mmc layer in which buffers which weren't
necessarily DMA-able were passed.
[Use sizeof(*wl->buffer_32) instead of sizeof(u32) -- Luca]
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We have no idea how many VIFs there are requiring a special spare, we
know just about the number of keys set. Rename the counter appropriately
and toggle it whenever a special key is added/removed.
Previously this was only changed once, since it was toggled whenever
the actual spare was changed.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
FW API changed and now PERIODIC_SCAN_REPORT_EVENT is sent
in case results were found at the end of each sched scan
cycle. Previous FW was missing that and broke sched scan.
This API change is available from 18xx FW 8.5.0.0.27
[Arik - move changes to 18xx specific files, align FW structures to
latest for scan command]
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Don't use MIMO rates when HT mode is forced to SISO, even if we have
multiple antennas.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Remove the STA specific ba_rx_bitmap field and use the common links
structure. This simplifies code setting/checking the BA bitmap.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Protect all functions touching queue_stop_reasons by spin-lock, since
they are accessed by op_tx. Now there's no need to take the mutex
before caling wlcore_queue_xxx functions.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Start using the new hw_queue mechanism in mac80211 and give each AC in
each vif its own hw_queue number. This allows us to stop an AC in a vif
independently from other vifs.
Change the Tx watermark handling functions to count packets per AC in
vif. From now on fast links should not be able to hurt the throughput
of slow links on the same AC but on different vifs.
Change internal queue mgmt functions to operate per vif, to support the
new Tx watermark granularity. Make the global versions of the queue
stop/start functions to use the global mac80211 API for queue mgmt. This
helps in situations where the driver currently doesn't know all the vifs
that reside in mac80211. Recovery is a good example for such a case.
[Moved hw_base_queue addition into the wlcore_tx_get_mac80211_queue()
function; changed WARN_ONs to WARN_ON_ONCEs; simplified for loops;
fixed new checkpatch warnings. -- Luca]
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Only allow a PSM STA to congest FW memory when it is the single active
link. Being a single STA doesn't imply a single link - there might be
other links on other roles.
[Changed WARN_ON to WARN_ON_ONCE -- Luca]
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Treat a single connected STA in PSM as a slow link and regulate Tx speed
according to slow link priority/stop thresholds.
This allows us to avoid flooding the FW, while delivering decent
throughput to a peer in forced-PSM.
[Small simplification of the if statements -- Luca]
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Update the 18xx FW status private part to include Tx related link
priorities. Introduce new HW ops to determine link priority per chip
family.
For 18xx the changes are:
- Suspended links are at most low priority and Tx for them is stopped
beyond the suspend threshold.
- Active links now get their thresholds directly from FW
- There's a new "stop" threshold for active links, at which point a link
stops receiving new packets.
Update the min 18xx FW version required to make sure suspended links
bitmap is advertised by the FW.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl->num_rx_desc was mistakenly initialized with WL18XX_NUM_TX_DESCRIPTORS
but it should use WL18XX_NUM_RX_DESCRIPTORS instead.
This bug was passed unnoticed because currently both RX and TX descriptors
are initialized to the same value (32).
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Even passive scans on DFS channels require us to send probe requests, so
configure the probe-req in this case.
Also use this opportunity to prevent the code from crashing in case no
SSIDs are sent from above. This will likely happen in the DFS case
introduced. Even a passive scan might need the probe request configured
because of DFS channels.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Treat Rx error code as a bitmask. This allows sending MIC failures
when other error bit are on.
Align Rx descriptor status mask to the FW definition.
Ease debugging in case FW reports failure to decrypt on packets.
Discard corrupted packets early in Rx path to avoid reporting other
abnormalities with corrupted packets that also have other failure bytes on.
Namely - we don't want to get a MIC failure on a corrupted packet.
This is mandated by the WiFi specification - see
section 11.4.2.4.1 in 802.11-2012.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
There's a limit on scan dwell times of max 30ms in order
to avoid degrading voip traffic which could be going on
while scanning. However these dwell times increase the
chance of missing out on nearby APs leading to partial
scan results. Allow configuration of longer dwell times
in case there no active interface (i.e. no STA associated
or AP up).
[Arik - count started vifs using an in-driver function]
[Fixed some new checkpatch warnings regarding comments in the
networking subsystem. -- Luca]
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Require each incoming packet to have a valid vif. The injected Tx code
path was buggy (and unused), so disallow it altogether.
Cleanup a few places and add a warning so we can better discover
anomalies (corrupted skbs?) masquerading as injected Tx.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
ACX_PEER_CAP command is just ACX_PEER_HT_CAP, but allows
configuring the peer's support rates as well.
this is needed because we start the station role when
the remote rates are not known yet.
the two commands should be unified in future fw versions,
but for now add a new set_peer_cap per-hw op, that will
use ACX_PEER_CAP for 18xx, and ACX_PEER_HT_CAP for 12xx.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Luciano Coelho <coelho@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Obtain the last Tx rate from the FW status and translate it to
the mac80211 rate+flag format before sending it up via the Tx status.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Prioritize EDCA by choosing the AC before anything else. Use the
fast/slow link bitmap in FW to improve the scheduling algorithm for
the multi-link scenario.
Set packet thresholds to determine if a given link is high or low
priority according to its speed. A slow link will be given high priority
if the amount of packets queued for it in the FW is lower than the
slow-threshold. Similarly, a fast link will be given high priority if
the number of its packets queued in FW is smaller than the high-threshold.
The improved algorithm:
1. Choose optimal AC according to FW utilization
2. Traversing the VIFs in a round-robin fashion, try to choose a high
priority link. Links are traversed in a round-robin fashion inside a
VIF.
3. If no high priority links are found, choose the first non-empty
(low priority) link found in the round robin.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Move FW-allocation tracking code to the fw_status function and track
allocations made by all links. These will be incorporated in the
improved Tx scheduling algorithm.
Manually zero the system link counters on op_stop, as this link is not
allocated the normal way.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This accounting will help find a vif that has data in a specific AC.
Otherwise we have to traverse all the links, which can be lengthy for
the AP case.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This allows us to pass only the link as a parameter to various functions
and deduce the wlvif. Note that this member will be NULL for global
links.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When a link is allocated, sometimes the "freed packets" counter in FW
is non zero, but we always assumed it is. This caused us to incorrectly
account FW allocated blocks in some cases.
When operating in AP mode, this bug caused some stations to never
come back from PSM.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wlcore allocates two static structs wl1271_band_2ghz & wl1271_band_5ghz
which are used/modified by Reg-Domain e.g. some channel might be marked
as passive at some point. Make sure we don't keep stale settings around
if the HW is unregistered/registered during operation.
[Arik - use Tx-power constant and tweak commit message]
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Make sure free_link is always called when removing an interface. This
ensures all skbs belonging to this interface are returned to mac80211.
Otherwise these dangling skbs might crash the system on the next
call to wl1271_tx_reset_link_queues(). This happens on recovery/stop or
an unsuccessful Tx flush.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Otherwise we risk contention for private members of our global structure
while op_stop_locked is running.
Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Sometimes the driver can perform a recovery while Tx is
active, this will trigger unnecessary warning which might
delay the recovery for more than 100 mS.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The 18xx fw supports greenfield so add the
IEEE80211_HT_CAP_GRN_FLD flag to the supported
ht capabilities flags.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When removing an interface currently performing a ROC operation, clear
the current ROC state. This is useful especially during recovery and
keeps mac80211 in sync to our state.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
all the current firmwares support elp, so
we can safely remove WLCORE_QUIRK_NO_ELP.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Under some circumstances, that fw might be asked to
remove a rx ba sessions it doesn't know about. In
this case, instead of triggering a recovery, accept
the error code (CMD_STATUS_NO_RX_BA_SESSION) and
ignore it.
[Arik - indicate failure up when the BA session cannot be setup]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Currently, each fw command/acx that return a status code
different than CMD_STATUS_SUCCESS will trigger a recovery
in the driver.
However, it is a valid for some fw commands to fail (e.g.
due to temporary lack of resources), so add new functions
that allow passing bitmap of valid error return values.
(make the current wl1271_cmd_send/wl1271_cmd_configure
wrappers around the new functions, in order to avoid
changing the whole driver)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
First set (low, medium and high TX power values) is used
for STA-HP background role. The 2nd set is used for other roles.
Update other mac/phy parameters according to new FW.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Conflicts:
drivers/net/wireless/ti/wl18xx/main.c
Update mac/phy paramters according to the default HP SISO boards.
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The 12xx FW doesn't support non-zero session ids for AP-mode. Introduce
an appropriate quirk to make sure the session id is always zero when
needed.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
For wl18xx, only the chip ID and the minor version number are
relevant. Ignore the other numbers which are either not used or
relate to internal projects or internal branches.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Previously we were only checking the single-role firmware version.
Now add code to check for the firmware versions separately for each
firmware type.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The firmware type and the project number fields in the firmware
version number, cannot be checked as if they increase sequentially,
because the former is the firmware type and the latter is an internal
project number. There's no guarantee that these numbers will remain
incremental, so use WLCORE_FW_VER_IGNORE.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The firmwares version string contain 5 integers. We used to consider
all the digits (except for the first one, which indicates the chip) as
linearly increasing version numbers. This is not correct, because
some of the integers indicate type of firmware (eg. single-role
vs. multi-role) or the internal project it was created for.
Besides, this varies a bit from chip to chip, so we need to make the
firmware version checks more flexible (eg. allow the lower driver to
ignore some of the integers). Additionally, we need to change the
code so that we only check for a linearly increasing number on the
fields where this actually makes sense.
Signed-off-by: Luciano Coelho <coelho@ti.com>
We don't distinguish between STA and AP firmwares anymore, so the
firmware version checking and quirks setting in wl12xx isn't needed
anymore.
Remove implementation of .identify_fw in wl12xx and deprecated
definitions. Don't remove the op entirely from wlcore, because it may
be needed for more fine-grained checking later.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Move wl12xx-specific chip ID macros to the wl12xx driver and rename
them to 127X and 128X for clarity since both the "1" (2.4GHz) and the
"3" (2.4GHz and 5GHz) variants use the same chip ID.
Signed-off-by: Luciano Coelho <coelho@ti.com>
add support for recovery settings including bug_on_recovery and
no_recovery options.
These options can now be set using wl18xx-conf.bin file and wlconf
tool.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
It's sometimes useful to gather information about the firmware
stability in long test runs, especially to see if problems are
recurring frequently or not. With this commit we count the number of
times a hardware recovery was issued and print it out during recovery
and in the driver_state in debugfs.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Adapt the new mac80211 BSS_CHANGED_PS notification,
and do the ps handling in mac80211's per-vif
callback (.bss_info_changed), rather than in
the per-device (.config) callback.
Make sure to configure it only after association.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
mask out CCK rates from the AP's local rates
when the interace is p2p interface (GO).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Try an opportunistic ROC when a STA is first added and stop the ROC when
the STA is removed or successfully authenticated. This would ensure we
don't miss auth/assoc/EAPOL packets during connection
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
18xx chips are capable of staying on 2 channels at the same time.
Introduce a chip-family specific parameter to set the number of channels
in the interface-combinations published by the driver.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Due to a bug, the fw asserts on fw log stop when dbg-pins are used.
Don't stop the fw log in this case.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We support changing the channel BW when we started the STA role on
a 40Mhz bandwidth. Otherwise a reconnection is required.
Save the started channel width and use it when channel width updates
arrive.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Allow configuring different dwell times to the different
scan types (regular and scheduled).
Add new configuration entry (dwell_time_dfs) to
conf_scan_settings, in order to allow setting
different values for normal scan and scheduled scan.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
we have done updating the driver to the new fw
api, so make the driver operational again.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The interface might go down before we got the SCHED_STOPPED
event, so make sure to call ieee80211_sched_scan_stopped()
if the scanned interface is removed.
Replace sched_scanning with sched_vif in order to save
the scanned interface.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In 18xx the calibration process of the PHY Cortex domain
requires to perform an active calibration of the channel
before it can be used for transmission. To fulfill world
wide regulatory restrictions, fw should be always
synchronized/updated with current CRDA configuration.
Add a new "CMD_DFS_CHANNEL_CONFIG" command to update the
fw with current reg-domain, this command passes a bit map
of channels that are allowed to be used for transmission.
The driver shall update the fw during initialization and
after each change in the current reg-domain
configuration. The driver will save the channel number of
incoming beacons during the scan process, as they might
be a result of the passive scan on
"IEEE80211_CHAN_PASSIVE_SCAN" channel and will update the
fw accordingly once the scan is finished, the purpose of
this is to be ready in case of the authentication request
on one of these disabled (uncalibrated) channels.
The new command requires to wait for the fw completion
event "DFS_CHANNELS_CONFIG_COMPLETE_EVENT".
No scan commands (including the sched scan) can be
executed concurrently with the "CMD_DFS_CHANNEL_CONFIG",
wl->mutex ensures that.
[Arik - move reset of reg_ch_conf_last to safe place inside
op_stop_locked]
[Eliad - adjust to new event waiting api]
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
A new session_id is generated on link allocation.
it is saved in a global array and used later, on tx.
The new fw api adds new bcast/global_session_id
fields to start_role(ap) command, and a new session_id
field to add_peer command. align the driver with it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
New fields were added to start_role(ap) and
set_peer_state commands, so the fw will be
able to know whether the sta/ap supports
wmm (the fw uses it in order to choose the
AC for some of its internally-generated frames)
For sta, take this value right from bss_conf->qos.
For ap, check for wmm support by looking for the
WMM IE in the configured beacon.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The event mailbox in wl18xx has a different
(non-compatible) structure.
Create common functions in wlcore to handle the
events, and call them from the chip-specific
event mailbox parsers.
This way, each driver (wl12xx/wl18xx) extracts
the event mailbox by itself according to its
own structure, and then calls the common
wlcore functions to handle it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Some fields were added to the channel_switch and
stop_channel_switch commands. Unfortunately,
the new 18xx channel_switch struct is not backward
compatible with the 12xx channel switch struct.
Add a new channel_switch op to wlcore, and update
the driver accordingly.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Some regdomains have more than 23 valid 5ghz channels,
so 18xx's MAX_CHANNELS_5GHZ was increased to 32.
Since now we have different max 5ghz channels values
for wl12xx and wl18xx, add a new wl->max_channels_5ghz
field, and use it for scan channels configuration.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The scan APIs of 12xx and 18xx are totally different.
Use some common functions as much as possible (e.g.
for setting scan channels), but split scan.c into
chip-specific scan.c files, each implementing its
own scan mechanism.
(in other words - move most of the current wlcore's
scan.c into wl12xx, and implement a similar mechanism
in 18xx, according to the new api)
New wlcore ops are introduced in order to call the
chip-specific scan functions.
The template indices used for each scan (regular/scheduled)
are also different between the chips, so set the correct
indices used for each scan type after identifying the chip.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The new fw (8.5.0.0.28) is not backward compatible
with older drivers.
Use a new fw name (along with bumping the min
fw version), and add some code to fail
any boot attempt during the fw api alignment
patches (as the driver is not functional in
these transitional patches).
This code will be removed after the api alignment
will be done.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
18xx and 12xx have different scan APIs. In 18xx,
the scan and the sched scan use the same struct.
Prepare the scan configuration functions to it, by taking
more generic params (e.g. ieee80211_channel) instead of
specific structs/requests.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When we stop sched scan during connection, we shouldn't
call ieee80211_sched_scan_stopped directly, but do it
in the normal flow, as part of the SCHED_SCAN_COMPLETED
event handling.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Remove goto and label in the code where a simple if can be used. If
nothing else, this is at least confusing git diff, which shows the
label name as the name of the function.
Signed-off-by: Luciano Coelho <coelho@ti.com>
In multi-vif setup it's useful to know the role_id
being configured.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
With the new connection flow, start_sta is called before
the remote rates where updated. Use our own supported rates
instead to make sure we don't disable any potential rate
(the rate policies will be updated later, but there is
currently no way to update the remote rates)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Pass a variable indicating whether HT is enabled,
instead of duplicating the function call with
different arguments.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When first configuring the rate policy, before auth,
we still don't have the correct rates that were
agreed during association.
Reconfigure the rate policy on association in order
to update them.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The supported_rates field should contain all our supported
rates, even if the remote peer doesn't support them.
(rename CONF_TX_AP_ENABLED_RATES to CONF_TX_ENABLED_RATES,
as we now use it for both ap and sta)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The default ps mode of the fw is auto, while the default
ps mode of mac80211 is active (ps off).
In order to sync them, configure active ps on association.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use the sta_state notifications to ROC when a station
is about to connect, and CROC respectively on
authorization (success) / deletion (failure).
Change the wl12xx_update_sta_state() flow to bail out
only on error, so multiple code blocks could refer
to the same state.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add some basic chanctx implementation - debug prints,
and save the vif's channel/band/type.
After that, we no longer need to handle channel change
notifications on op_config.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We care only about the operational channel, not
about the temporal hw channel (which won't have
any real meaning in multi-channel env anyway)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
implement the reamin_on_channel() callback by starting
a dev role (already associated with the current vif)
on the requested channel/band.
This channel is usually different from the channel
of the sta role, so pass it to wl12xx_roc() as well,
and notify mac80211 (async) when the fw is ready
on the new channel.
Now, in case of offchannel tx, we should use the dev
role hlid, instead of the sta hlid.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
for some reason, the wl12xx fw is not able to rx/tx
on the first start_sta cmd.
Workaround it by issuing a dummy start_sta + stop_sta
before starting the sta for the final time.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Make the connection flow simpler by starting
sta role on bssid change.
Currently, we start dev role when going idle-off,
and start the sta role only after association
indication. This complicates the connection
flow with some possible intermediate states.
Make it simpler by starting sta role on bssid change,
which now happens *before* auth req get sent.
Update the handling of mac80211's notifications
and change wl1271_join/unjoin accordingly -
* Split wl1271_join() into wlcore_join (tuning on
a channel/bssid) and wlcore_set_assoc (configure
sta after association).
* Rename wl1271_unjoin() to wlcore_unset_assoc(), as
it is no longer the inversion of wl1271_join()
(now it's only used to disconnect associated sta /
joined ibss, without stopping the role).
* Set ssid before starting station role (needed for
start_role(sta)
While on it, split wl1271_bss_info_changed_sta() into
some sub-functions.
since we no longer use dev role in the connection flow,
we now always use the hlid of the sta role.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.
This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No need to check whether unsigned variable is less than 0.
CC: Luciano Coelho <coelho@ti.com>
CC: linux-wireless@vger.kernel.org
CC: netdev@vger.kernel.org
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The return value of wait_for_completion_timeout() is always
>= 0 with unsigned int type.
So the condition "ret < 0" or "ret >= 0" is pointless.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
In corner case for wl12xx_spi_raw_write() when
len == SPI_AGGR_BUFFER_SIZE
we don't setup correctly spi transfer_list.
Next we will have garbage and strange errors
reported by SPI framework (eg. wrong speed_hz,
failed to transfer one message from queue)
when iterate transfer_list.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
CC: Luciano Coelho <coelho@ti.com>
CC: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The function wl12xx_set_power_on is only called twice, once in
wl12xx_chip_wakeup and once in wl12xx_get_hw_info. On the failure of the
call in wl12xx_chip_wakeup, the containing function just returns, but on
the failure of the call in wl12xx_get_hw_info, the containing function
calls wl1271_power_off. This does not seem necessary, because if
wl12xx_set_power_on has set the power on and then fails, it has already
turned the power off.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f,free,a;
parameter list[n] ps;
type T;
expression e;
@@
f(ps,T a,...) {
... when any
when != a = e
if(...) { ... free(a); ... return ...; }
... when any
}
@@
identifier r.f,r.free;
expression x,a;
expression list[r.n] xs;
@@
* x = f(xs,a,...);
if (...) { ... free(a); ... return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Allow drivers to indicate their mactime is at RX completion and adjust
for this in mac80211. Also rename the existing RX_FLAG_MACTIME_MPDU to
RX_FLAG_MACTIME_START to clarify its intent. Based on similar code by
Johannes Berg.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[fix docs, atheros drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During hardware restart, all interfaces are iterated even
though they haven't been re-added to the driver, document
this behaviour. The same also happens during resume, which
is even more confusing since all of the interfaces were
previously removed from the driver. Make this optional so
drivers relying on the current behaviour can still use it,
but to let drivers that don't want this behaviour disable
it.
Also convert all API users, keeping the old semantics
except in hwsim, where the new normal ones are desired.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wlcore_op_set_key() calls wl18xx_set_key(),
which in turn executes some of his function
calls without acquiring wl->mutex and making
sure the fw is awake.
Adding mutex_lock()/ps_elp_wakeup() calls is
not enough, as wl18xx_set_key() calls
wl1271_tx_flush() which can't be called while
the mutex is taken.
Add the required calls to wlcore_op_set_key,
but limit the queues_stop and flushing
to the only encryption types in which
a spare block might be needed (GEM and TKIP).
[Arik - move state != ON check]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The current elp timeout (the same as the dynamic
ps timeout - 1500ms) is too high. Usually,
wl1271_ps_elp_sleep() get called right after tx/rx,
which is fine, but some command might get sent
even when there is no traffic (e.g. ht changes
triggered by beacon frames), and leaving the
device awake for 1500ms in this case is redundant.
Use a timeout of 30ms.
The fw won't enter elp anyway before the dynamic-ps
timeout was expired as well (and it entered ps
successfully).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The NVS file is loaded by the device's probe callback with the help of
request_firmware(). Since request_firmware() relies on udevd, the
modules cannot be loaded before hotplug events are handled.
Fix this by loading the NVS file asynchronously and continue
initialization only after the firmware request is over.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Move most of the device-specific probe functionality into setup(), a new
op. By doing this, wlcore_probe will be the first to request a firmware
from userspace, making it easier to load the NVS file asynchronously.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
When the no_recovery flag is used, the recovery work will not restart
the FW and the state will not be set to 'on'. To enable post-mortem
analysis, allow memory access in the 'restarting' state.
Also, since the FW might not be operational, don't fail the read/write
operations if elp_wakeup fails.
Reported-by: Arkady Miasnikov <a-miasnikov@ti.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Currently, all the (station) roles use the same
keep-alive template id (0). However, the klv
template ids shouldn't be shared by different
roles.
Implement a simple klv_templates bitmap, and let
each role allocate its own klv template id on
role initialization.
[Arik - remove invalidation of KLV template when getting into "idle".
This is already handled in unjoin]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Previously, invalidation of the keep-alive template was
done when going idle. However, while removing the
idle-handling we didn't move the keep-alive template
invalidation to another place.
This finally resulted in fw error when trying to use
the keep-alive template by another role.
(Note that we still have an error here - each role
should have its unique keep-alive template id, while
currently they all use CMD_TEMPL_KLV_IDX_NULL_DATA (0).
This only works now because we don't support concurrent
connected stations yet)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The driver used siso20 in this case for legacy reasons.
Reported-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The interrupt line is enabled by wl12xx_enable_interrupts and
wl18xx_enable_interrupts, but it will not be disabled in all failure
paths. Fix this.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
While recursive recovery is avoided during shutdown, a new recovery may
be queued when the FW boots. The recovery work will then try to stop an
already stopped hardware, which will most likely result in a kernel
panic.
Fix this by verifying that wl->state is on before queueing a new
recovery.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
add phy_fw_version_str to debugfs driver_state file.
information is taken during boot and stored in wl->chip.phy_fw_ver_str.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Limit SPI transmissions to the wl12xx max buffer size, as only 12xx was
tested with SPI.
This allows us to remove the global aggregation buffer constant.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Use number_of_assembled_ant5 phy param to indicate if A band is enabled:
if number_of_assembled_ant5 != 0 then it is enabled otherwise it is
disabled.
This aligns with phy implementation that uses this param both to indicate
if band is active and the number of antennas.
This parameter replaces enable_11a module param that was removed.
User-Space applications can use wlconf and/or INI files to disable A band
using this parameter.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
This allows us to have a p2p-management interface (in STA mode),
as we as a group dedicated interface.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Enable device roles just before starting it.
This way, a single device role should be enough
for all vifs, as we can't use concurrent device
roles (which require ROC) anyway.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
enabled (but not-started) sta role should be good enough
for scanning (both normal and scheduled), so use it
instead of the device_role.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Make debug prints operational when dynamic debug is not defined.
This allows better debugging in production environments.
Change the driver prefix to "wlcore" while were at it.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Allow 3 native mac addresses on 18xx. On 12xx allow 2 native mac
addresses and set the LAA bit to create a third mac address. This
enabled operation with a separate group interface.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
mac80211's resume() callback might get called even if
the sta is not associated (but only up). The
resume sequence in this case results in configuring
the wake-up conditions of a non-started role, which
causes fw assertion.
Fix it by bailing out if the STA is not connected
(like we do on suspend()).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
wowlan filters should be configured in any case in suspend/resume.
This shouldn't be dependent on whether wakeup conditions are the
same for suspend and resume states. Only the FW command to
reconfigure wakeup conditions should be avoided in such a case.
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Aggregation buffer size is set separately per 18xx/12xx chip family.
For 18xx aggragation buffer is set to 13 pages to utilize all
the available tx/rx descriptors for aggregation.
[Arik - remove redundant parts from the patch]
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Force Tx during the flush if there are packets pending in the driver.
This actually solves a bug where we would get called from the mac80211
wq context, which would prevent tx_work from getting queued, even when
the mutex is unlocked.
Don't stop the queues needlessly if there's nothing to flush. Use a
larger delay when sleeping to give the driver a chance to flush and
avoid cpu busy looping. Re-arrange the loop so the last iteration is
not wasted.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Print how much time a flush took. This will help debug the time it takes
to switch between channels.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The IEEE80211_TX_CTL_NO_CCK_RATE flag is only set for mgmt packets
transmitted during p2p connection setup. Make sure to use the lowest
OFDM rate guarantee the peer always hears us.
Change the p2p rate policy to contain only the 6mpbs rate to acheive
this effect.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
