the BMA250 has only 10-bit resolution; while the data readout registers
have identical layout, the configuration is completely different compared
to the BMA180
datasheet: http://ae-bst.resource.bosch.com/media/products/dokumente/bma250/BST-BMA250-DS002-05.pdf
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for KXTJ2-1009 3-axis acceleromenter sensor.
KXTJ2-1009 uses the same register definitions as KXCJK-1013.
The specification for KXTJ2-1009 can be downloaded from:
http://www.kionix.com/sites/default/files/KXTJ2-1009%20Specifications%20Rev%204.pdf
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The following chips are either similar or have only the resolution
different. Hence, change this driver to support these chips too:
BMI055 - combo chip (accelerometer part is identical to BMC150's)
BMA255 - identical to BMC150's accelerometer
BMA222E - 8 bit resolution
BMA250E - 10 bit resolution
BMA280 - 14 bit resolution
Additionally:
* add bmc150_accel_match_acpi_device() function to check that the device
has been enumerated through ACPI;
* rename bmc150_accel_acpi_gpio_probe() to bmc150_accel_gpio_probe()
since the ACPI matching has been moved to the new function. Also, this
will allow for the GPIO matching to be done against a device tree too, not only
ACPI tree;
* rename bmc150_scale_info struct member 'range' to 'reg_range' to be
consistent with the naming convention used elsewhere in the driver
and declare it u8, instead of int;
* change CONFIG description to list all supported chips;
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for KXCJ9-1008 3-axis acceleromenter sensor.
KXCJ9-1008 uses the same register definitions as KXCJK-1013.
The specification for KXCJ9-1008 can be downloaded from:
http://www.kionix.com/sites/default/files/KXCJ9-1008%20Specifications%20Rev%205.pdf
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This change implements BMC150 accelerometer driver. A BMC150 package
consist of a compass and an accelerometer. This driver only implements
accelerometer part.
Spec downloaded from:
http://ae-bst.resource.bosch.com/media/products/dokumente/bmc150/BST-BMC150-DS000-03.pdf
This sensor chip supports many advanced features, but this driver
implements minimum feature set which is a must to be useful.
This driver can be enhanced incrementally.
If the sensor vendor wants to update full featured version, they
can substitute or enhance this driver when they get chance.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds IIO driver for KXCJK 1013 triaxis accelerometer sensor.
The specifications for this driver is downloaded from:
http://www.kionix.com/sites/default/files/KXCJK-1013%20Specifications%20Rev%202.pdf
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
3-axis accelerometer sensor (2/4/8 g) with 12-bit resolution
and I2C interface
many extra features are unsupported (freefall detection, orientation
change, autosleep)
datasheet is here:
http://cache.freescale.com/files/sensors/doc/data_sheet/MMA8452Q.pdf
v2: (thanks to Jonathan Cameron)
* use ARRAY_SIZE()
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Keeping Makefile and Kconfig entries in alphabetical order usually works better
than just appending new entries at the end, since it reduces the amount of
conflicts. This patch adds a comment to the IIO Kconfig and Makefile files to
document that the entries should be kept in alphabetical order.
Also reorder those entries which weren't in alphabetical order yet.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Drivers for STMicroelectronics accelerometers, gyroscopes, and
magnetometers were added in v3.9. They all have a (similar) select
statement in their Kconfig files for a non-existant Kconfig symbol.
These select statements can safely be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Not much to say, without that change, hid-sensor-trigger will be
always compiled if HID_SENSOR_IIO_COMMON is selected which fails if
CONFIG_IIO_TRIGGER is not set because CONFIG_IIO_CONSUMERS_PER_TRIGGER
will not be defined.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added usage id processing for Accelerometer 3D.This uses IIO
interfaces for triggered buffer to present data to user
mode.This uses HID sensor framework for registering callback
events from the sensor hub.
Signed-off-by: srinivas pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
