Currently, the EEH recovery process considers passed-through devices
as if they were not EEH-aware, which can cause them to be removed as
part of recovery. Because device removal requires cooperation from
the guest, this may lead to the process stalling or deadlocking.
Also, if devices are removed on the host side, they will be removed
from their IOMMU group, making recovery in the guest impossible.
Therefore, alter the recovery process so that passed-through devices
are not removed but are instead left frozen (and marked isolated)
until the guest performs it's own recovery. If firmware thaws a
passed-through PE because it's parent PE has been thawed (because it
was not passed through), re-freeze it.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a parameter to eeh_clear_pe_frozen_state() that allows
passed-through PEs to be excluded. Update callers to always pass true
so that there is no change in behaviour.
This is to prepare for follow-up work for passed-through devices.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a parameter to eeh_pe_state_clear() that allows passed-through PEs
to be excluded. Update callers to always pass true so that there is no
change in behaviour.
Also refactor to use direct traversal, to allow the removal of some
boilerplate.
This is to prepare for follow-up work for passed-through devices.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
eeh_unfreeze_pe() performs two operations: unfreezing a PE (which may
cause firmware to unfreeze child PEs as well) and de-isolating the PE
and it's children.
To simplify this and support future work, separate out the
de-isolation and perform it at the call sites (when necessary).
There should be no change in behaviour.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The 'clear_sw_state' parameter for eeh_pe_clear_frozen_state() is
redundant because it has no effect (except in the rare case of a
hardware error part way through unfreezing a tree of PEs, where it
would dangerously allow partial de-isolation before returning
failure).
It is passed down to __eeh_pe_clear_frozen_state(), and from there to
eeh_unfreeze_pe(), where it causes EEH_PE_ISOLATED to be removed
from the state of each PE during the traversal. However, when the
traversal finishes, EEH_PE_ISOLATED is unconditionally removed by a
call to eeh_pe_state_clear() regardless of the parameter's value.
So remove the flag and pass false to eeh_unfreeze_pe() (to avoid the
rare case described above, as it was before the flag was introduced).
Also, perform the recursion directly in the function and eliminate a
bit of boilerplate.
There should be no change in functionality, except as mentioned above.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit c40dd2f766 ("powerpc: Add System RAM to /proc/iomem")
it is possible to use the generic walk_system_ram_range() and
the generic page_is_ram().
To enable the use of walk_system_ram_range() by the IBM EHEA ethernet
driver, we still need an export of the generic function.
As powerpc was the only user of CONFIG_ARCH_HAS_WALK_MEMORY, the
ifdef around the generic walk_system_ram_range() has become useless
and can be dropped.
Fixes: c40dd2f766 ("powerpc: Add System RAM to /proc/iomem")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Keep the EXPORT_SYMBOL_GPL in powerpc code]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
SO_RCVTIMEO and SO_SNDTIMEO socket options use struct timeval
as the time format. struct timeval is not y2038 safe.
The subsequent patches in the series add support for new socket
timeout options with _NEW suffix that will use y2038 safe
data structures. Although the existing struct timeval layout
is sufficiently wide to represent timeouts, because of the way
libc will interpret time_t based on user defined flag, these
new flags provide a way of having a structure that is the same
for all architectures consistently.
Rename the existing options with _OLD suffix forms so that the
right option is enabled for userspace applications according
to the architecture and time_t definition of libc.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Cc: ccaulfie@redhat.com
Cc: deller@gmx.de
Cc: paulus@samba.org
Cc: ralf@linux-mips.org
Cc: rth@twiddle.net
Cc: cluster-devel@redhat.com
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-alpha@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: sparclinux@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the static keyword around to remove the following warnings (W=1):
arch/powerpc/platforms/ps3/os-area.c:212:1: error: 'static' is not at beginning of declaration [-Werror=old-style-declaration]
arch/powerpc/platforms/ps3/system-bus.c:45:1: error: 'static' is not at beginning of declaration [-Werror=old-style-declaration]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is not point in having a trailing semicolon after a closing curly
brace. Remove it.
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds support for generating bpf line info for
JITed programs.
Signed-off-by: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Enable kernel XZ compression option on 44x.
Tested on a Western Digital - MyBook Live NAS.
It takes 22 seconds for the 800 MHz CPU to decompress
and boot a 2.63 MiB XZ-compressed kernel simpleImage.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead provide a proper implementation in the direct mapping code, and
also wire it up for arm and powerpc, leaving an error return for all the
IOMMU or virtual mapping instances for which we'd have to wire up an
actual implementation
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
When binding an SCM volume to a physical address the hypervisor has the
option to return early with a continue token with the expectation that
the guest will resume the bind operation until it completes. A quirk of
this interface is that the bind address will only be returned by the
first bind h-call and the subsequent calls will return
0xFFFF_FFFF_FFFF_FFFF for the bind address.
We currently do not save the address returned by the first h-call. As a
result we will use the junk address as the base of the bound region if
the hypervisor decides to split the bind across multiple h-calls. This
bug was found when testing with very large SCM volumes where the bind
process would take more time than they hypervisor's internal h-call time
limit would allow. This patch fixes the issue by saving the bind address
from the first call.
Cc: stable@vger.kernel.org
Fixes: b5beae5e22 ("powerpc/pseries: Add driver for PAPR SCM regions")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With support for split pmd lock, we use pmd page pmd_huge_pte pointer
to store the deposited page table. In those config when we move page
tables we need to make sure we move the deposited page table to the
correct pmd page. Otherwise this can result in crash when we withdraw
of deposited page table because we can find the pmd_huge_pte NULL.
eg:
__split_huge_pmd+0x1070/0x1940
__split_huge_pmd+0xe34/0x1940 (unreliable)
vma_adjust_trans_huge+0x110/0x1c0
__vma_adjust+0x2b4/0x9b0
__split_vma+0x1b8/0x280
__do_munmap+0x13c/0x550
sys_mremap+0x220/0x7e0
system_call+0x5c/0x70
Fixes: 675d995297 ("powerpc/book3s64: Enable split pmd ptlock.")
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To match its x86 counterpart, save_stack_trace_tsk_reliable() should
return -EINVAL in cases that it is currently returning 1. No caller is
currently differentiating non-zero error codes, but let's keep the
arch-specific implementations consistent.
Signed-off-by: Joe Lawrence <joe.lawrence@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Mostly cosmetic changes:
- Group common stack pointer code at the top
- Simplify the first frame logic
- Code stackframe iteration into for...loop construct
- Check for trace->nr_entries overflow before adding any into the array
Suggested-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Joe Lawrence <joe.lawrence@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The bottom-most stack frame (the first to be unwound) may be largely
uninitialized, for the "Power Architecture 64-Bit ELF V2 ABI" only
requires its backchain pointer to be set.
The reliable stack tracer should be careful when verifying this frame:
skip checks on STACK_FRAME_LR_SAVE and STACK_FRAME_MARKER offsets that
may contain uninitialized residual data.
Fixes: df78d3f614 ("powerpc/livepatch: Implement reliable stack tracing for the consistency model")
Signed-off-by: Joe Lawrence <joe.lawrence@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make the HAVE_RELIABLE_STACKTRACE Kconfig option depend on
PPC_BOOK3S_64 for documentation purposes. Before this patch, it
depended on PPC64 && CPU_LITTLE_ENDIAN and because CPU_LITTLE_ENDIAN
implies PPC_BOOK3S_64, there's no functional change here.
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Joe Lawrence <joe.lawrence@redhat.com>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The ppc64 specific implementation of the reliable stacktracer,
save_stack_trace_tsk_reliable(), bails out and reports an "unreliable
trace" whenever it finds an exception frame on the stack. Stack frames
are classified as exception frames if the STACK_FRAME_REGS_MARKER
magic, as written by exception prologues, is found at a particular
location.
However, as observed by Joe Lawrence, it is possible in practice that
non-exception stack frames can alias with prior exception frames and
thus, that the reliable stacktracer can find a stale
STACK_FRAME_REGS_MARKER on the stack. It in turn falsely reports an
unreliable stacktrace and blocks any live patching transition to
finish. Said condition lasts until the stack frame is
overwritten/initialized by function call or other means.
In principle, we could mitigate this by making the exception frame
classification condition in save_stack_trace_tsk_reliable() stronger:
in addition to testing for STACK_FRAME_REGS_MARKER, we could also take
into account that for all exceptions executing on the kernel stack
- their stack frames's backlink pointers always match what is saved
in their pt_regs instance's ->gpr[1] slot and that
- their exception frame size equals STACK_INT_FRAME_SIZE, a value
uncommonly large for non-exception frames.
However, while these are currently true, relying on them would make
the reliable stacktrace implementation more sensitive towards future
changes in the exception entry code. Note that false negatives, i.e.
not detecting exception frames, would silently break the live patching
consistency model.
Furthermore, certain other places (diagnostic stacktraces, perf, xmon)
rely on STACK_FRAME_REGS_MARKER as well.
Make the exception exit code clear the on-stack
STACK_FRAME_REGS_MARKER for those exceptions running on the "normal"
kernel stack and returning to kernelspace: because the topmost frame
is ignored by the reliable stack tracer anyway, returns to userspace
don't need to take care of clearing the marker.
Furthermore, as I don't have the ability to test this on Book 3E or 32
bits, limit the change to Book 3S and 64 bits.
Fixes: df78d3f614 ("powerpc/livepatch: Implement reliable stack tracing for the consistency model")
Reported-by: Joe Lawrence <joe.lawrence@redhat.com>
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Joe Lawrence <joe.lawrence@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add mem-loads/mem-stores events to sysfs.
The event is formed based on raw event encoding.
Primary PMU event used here is PM_MRK_INST_CMPL
along with MMCRA[SM] modes and Thresholding bit
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In htab_convert_pte_flags(), _PAGE_CACHE_CTL is used to check for the
_PAGE_SAO flag:
else if ((pteflags & _PAGE_CACHE_CTL) == _PAGE_SAO)
rflags |= (HPTE_R_W | HPTE_R_I | HPTE_R_M);
But, it isn't defined to include that flag:
#define _PAGE_CACHE_CTL (_PAGE_NON_IDEMPOTENT | _PAGE_TOLERANT)
This happens to work, but only because of the flag values:
#define _PAGE_SAO 0x00010 /* Strong access order */
#define _PAGE_NON_IDEMPOTENT 0x00020 /* non idempotent memory */
#define _PAGE_TOLERANT 0x00030 /* tolerant memory, cache inhibited */
To prevent any issues if these particulars ever change, add _PAGE_SAO to
the mask.
Suggested-by: Charles Johns <crjohns@us.ibm.com>
Signed-off-by: Reza Arbab <arbab@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove linux/syscalls.h which is included more than once
Signed-off-by: Sabyasachi Gupta <sabyasachi.linux@gmail.com>
Acked-by: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove linux/printk.h which is included more than once.
Signed-off-by: Sabyasachi Gupta <sabyasachi.linux@gmail.com>
Acked-by: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove linux/rtc.h which is included more than once
Signed-off-by: Brajeswar Ghosh <brajeswar.linux@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On pseries systems, performing a partition migration can result in
altering the nodes a CPU is assigned to on the destination system. For
exampl, pre-migration on the source system CPUs are in node 1 and 3,
post-migration on the destination system CPUs are in nodes 2 and 3.
Handling the node change for a CPU can cause corruption in the slab
cache if we hit a timing where a CPUs node is changed while cache_reap()
is invoked. The corruption occurs because the slab cache code appears
to rely on the CPU and slab cache pages being on the same node.
The current dynamic updating of a CPUs node done in arch/powerpc/mm/numa.c
does not prevent us from hitting this scenario.
Changing the device tree property update notification handler that
recognizes an affinity change for a CPU to do a full DLPAR remove and
add of the CPU instead of dynamically changing its node resolves this
issue.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael W. Bringmann <mwb@linux.vnet.ibm.com>
Tested-by: Michael W. Bringmann <mwb@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-01-29
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Teach verifier dead code removal, this also allows for optimizing /
removing conditional branches around dead code and to shrink the
resulting image. Code store constrained architectures like nfp would
have hard time doing this at JIT level, from Jakub.
2) Add JMP32 instructions to BPF ISA in order to allow for optimizing
code generation for 32-bit sub-registers. Evaluation shows that this
can result in code reduction of ~5-20% compared to 64 bit-only code
generation. Also add implementation for most JITs, from Jiong.
3) Add support for __int128 types in BTF which is also needed for
vmlinux's BTF conversion to work, from Yonghong.
4) Add a new command to bpftool in order to dump a list of BPF-related
parameters from the system or for a specific network device e.g. in
terms of available prog/map types or helper functions, from Quentin.
5) Add AF_XDP sock_diag interface for querying sockets from user
space which provides information about the RX/TX/fill/completion
rings, umem, memory usage etc, from Björn.
6) Add skb context access for skb_shared_info->gso_segs field, from Eric.
7) Add support for testing flow dissector BPF programs by extending
existing BPF_PROG_TEST_RUN infrastructure, from Stanislav.
8) Split BPF kselftest's test_verifier into various subgroups of tests
in order better deal with merge conflicts in this area, from Jakub.
9) Add support for queue/stack manipulations in bpftool, from Stanislav.
10) Document BTF, from Yonghong.
11) Dump supported ELF section names in libbpf on program load
failure, from Taeung.
12) Silence a false positive compiler warning in verifier's BTF
handling, from Peter.
13) Fix help string in bpftool's feature probing, from Prashant.
14) Remove duplicate includes in BPF kselftests, from Yue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In Kbuild, if_changed and friends must have FORCE as a prerequisite.
Hence, $(filter-out FORCE,$^) or $(filter-out $(PHONY),$^) is a common
idiom to get the names of all the prerequisites except phony targets.
Add real-prereqs as a shorthand.
Note:
We cannot replace $(filter %.o,$^) in cmd_link_multi-m because $^ may
include auto-generated dependencies from the .*.cmd file when a single
object module is changed into a multi object module. Refer to commit
69ea912fda ("kbuild: remove unneeded link_multi_deps"). I added some
comment to avoid accidental breakage.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
This patch implements code-gen for new JMP32 instructions on ppc.
For JMP32 | JSET, instruction encoding for PPC_RLWINM_DOT is added to check
the result of ANDing low 32-bit of operands.
Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com>
Cc: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The IPC system call handling is highly inconsistent across architectures,
some use sys_ipc, some use separate calls, and some use both. We also
have some architectures that require passing IPC_64 in the flags, and
others that set it implicitly.
For the addition of a y2038 safe semtimedop() system call, I chose to only
support the separate entry points, but that requires first supporting
the regular ones with their own syscall numbers.
The IPC_64 is now implied by the new semctl/shmctl/msgctl system
calls even on the architectures that require passing it with the ipc()
multiplexer.
I'm not adding the new semtimedop() or semop() on 32-bit architectures,
those will get implemented using the new semtimedop_time64() version
that gets added along with the other time64 calls.
Three 64-bit architectures (powerpc, s390 and sparc) get semtimedop().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
We are trying to get rid of BUS_ATTR() and the usage of that in
ibmebus.c can be trivially converted to use BUS_ATTR_WO(), so use that
instead.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to provide non-atomic functions for io{read|write}64 that will
use readq and writeq when appropriate. We define a number of variants
of these functions in the generic iomap that will do non-atomic
operations on pio but atomic operations on mmio.
These functions are only defined if readq and writeq are defined. If
they are not, then the wrappers that always use non-atomic operations
from include/linux/io-64-nonatomic*.h will be used.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Suresh Warrier <warrier@linux.vnet.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adopt nvram module to reduce code duplication. This means CONFIG_NVRAM
becomes available to PPC64 builds. Previously it was only available to
PPC32 builds because it depended on CONFIG_GENERIC_NVRAM.
The IOC_NVRAM_GET_OFFSET ioctl as implemented on PPC64 validates the
offset returned by pmac_get_partition(). Do the same in the nvram module.
Note that the old PPC32 generic_nvram module lacked this test.
So when CONFIG_PPC32 && CONFIG_PPC_PMAC, the IOC_NVRAM_GET_OFFSET ioctl
would have returned 0 (always). But when CONFIG_PPC64 && CONFIG_PPC_PMAC,
the IOC_NVRAM_GET_OFFSET ioctl would have returned -1 (which is -EPERM)
when the requested partition was not found.
With this patch, the result is now -EINVAL on both PPC32 and PPC64 when
the requested PowerMac NVRAM partition is not found. This is a userspace-
visible change, in the non-existent partition case, which would be in
an error path for an IOC_NVRAM_GET_OFFSET ioctl syscall.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch PPC32 kernels from the generic_nvram module to the nvram module.
Also fix a theoretical bug where CHRP omits the chrp_nvram_init() call
when CONFIG_NVRAM_MODULE=m.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the nvram_size() function to those PowerPC platforms that don't already
have one: CHRP and PowerMac. This means that the ppc_md.nvram_size()
function can be called by nvram_get_size().
Since we are addressing CHRP inconsistencies here, rename chrp_nvram_read
and chrp_nvram_write, which break the naming convention used across
powerpc platforms for NVRAM accessor functions.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the nvram_read_byte() and nvram_write_byte() declarations in
powerpc/include/asm/nvram.h and use the cross-platform static functions
in linux/nvram.h instead.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For PowerPC PMUs that do not support context exclusion let's
advertise the PERF_PMU_CAP_NO_EXCLUDE capability. This ensures that
perf will prevent us from handling events where any exclusion flags
are set. Let's also remove the now unnecessary check for exclusion
flags.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: robin.murphy@arm.com
Cc: suzuki.poulose@arm.com
Link: https://lkml.kernel.org/r/1547128414-50693-10-git-send-email-andrew.murray@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQJEBAABCgAuFiEEktVUI4SxYhzZyEuo+vtdtY28YcMFAlxDUjkQHHJvYmhAa2Vy
bmVsLm9yZwAKCRD6+121jbxhwzTBD/9MfQbCzF5IcgW+alp7fKqoFH5MQUkwEQgO
TJ7TO/CgrnT/uDjUe90tfixsF7A4orpK8h8FWczLF22Ksnirqaxv4Gcmj0ItGQlD
TeTzCV7DW6Kgcv6weQjH5PohB3XUKzHQe8/MdZCXnn/ikQpKK5bmQEV3Kxw1s4zM
jHIwMGcDy+EKbcLPpq/lhLyCR7Ce3SrzCtrY41rw+tpgi450A72g0/sOf5onb/Xz
+/akwRl8lIfcIl21+wMA4zyLOHVeqio+xvXSiYB31z82Pv2v4hGLxjTqBVfPLhpq
1qJI1ua4v+424RLBNInuEf3+lnUkNizjT38INw0zw+E86TLtQYj1n/m2upoVsRE3
ggLWVnxlWEIebDhpLySnKW9R58fYxXSq+qaP2jOKkGjzx+0HCZDVIjZwZx3C2Vft
sMAVSNKd+Mche6GGGEhcPxmKnMIh6P2XyIo/60hv8JqYY6CwqxBGyCGQvCck38AA
OySmMnS7q31pwiS3m6/RnlLiL6JmHeI/P5FRmPUak68Gbsp7dddcw6dIFUuOBsnF
QQpuq99cG4r3e9Az5/A45KNrR5MyZVJHoZj0CmjLPRnQuJsPvpEk5BQi2rmH5jSG
F/BPcFU9/+r65tDVYVmOaaHfqOWk9oeoxGR+e8ve/MpfTktid7to/dLv9smqs0UB
XdHeh+jepg==
=6H3h
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree fix from Rob Herring:
"A single build fix for powerpc due to device_node.type removal"
* tag 'devicetree-fixes-for-5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
powerpc: chrp: Use of_node_is_type to access device_type
Commit 8ce5f84157 ("of: Remove struct device_node.type pointer")
removed struct device_node.type pointer, but the conversion to use
of_node_is_type() accessor was missed in chrp_init_IRQ().
Fixes: 8ce5f84157 ("of: Remove struct device_node.type pointer")
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Rob Herring <robh@kernel.org>
A couple of weeks of fixes.
There's one fix for an oops on Power9 machines with Open CAPI adapters.
And a fix for probable memory corruption in some of the new NPU code, caught by
smatch though and not seen in the wild.
Plus a few other minor fixes.
There's one non-fix which is the perf_regs change. That was sent during the
merge window but I accidentally only merged the first of two patches in the
series. It's been in linux-next so hopefully doesn't conflict with anything in
acme's tree.
Thanks to:
Alexey Kardashevskiy, Andrew Donnellan, Breno Leitao, Christian Lamparter,
Christophe Leroy, Dan Carpenter, Frederic Barrat, Greg Kurz, Jason A.
Donenfeld, Madhavan Srinivasan.
-----BEGIN PGP SIGNATURE-----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=hlZ7
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A couple of weeks of fixes.
There's one fix for an oops on Power9 machines with Open CAPI
adapters.
And a fix for probable memory corruption in some of the new NPU code,
caught by smatch though and not seen in the wild.
Plus a few other minor fixes.
There's one non-fix which is the perf_regs change. That was sent
during the merge window but I accidentally only merged the first of
two patches in the series. It's been in linux-next so hopefully
doesn't conflict with anything in acme's tree.
Thanks to: Alexey Kardashevskiy, Andrew Donnellan, Breno Leitao,
Christian Lamparter, Christophe Leroy, Dan Carpenter, Frederic Barrat,
Greg Kurz, Jason A. Donenfeld, Madhavan Srinivasan"
* tag 'powerpc-5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/syscalls: Fix syscall tracing
powerpc/pseries: Fix build break due to pnv_npu2_init()
powerpc/4xx/ocm: Fix fix for phys_addr_t printf warnings
powerpc/powernv/npu: Fix oops in pnv_try_setup_npu_table_group()
powerpc/tm: Limit TM code inside PPC_TRANSACTIONAL_MEM
powerpc/8xx: fix setting of pagetable for Abatron BDI debug tool.
powerpc/powernv/npu: Allocate enough memory in pnv_try_setup_npu_table_group()
powerpc/perf: Update perf_regs structure to include MMCRA
Recently in commit fbf508da74 ("powerpc: split compat syscall table
out from native table") we changed the layout of the system call
table. Instead of having two entries for each syscall number, one for
the regular entry point and one for the compat entry point, we now
have separate tables for regular and compat entry points.
This inadvertently broke syscall tracing (CONFIG_FTRACE_SYSCALLS),
because our implementation of arch_syscall_addr() knew about the
layout of the table (it did nr * 2).
We can fix it just by dropping our version of arch_syscall_addr() and
using the generic version which does:
return (unsigned long)sys_call_table[nr];
Fixes: fbf508da74 ("powerpc: split compat syscall table out from native table")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 3be2df00e2 ("powerpc/pseries/npu: Enable platform support")
added a call to pnv_npu2_init() in pseries code. This causes a build
break if we build with CONFIG_PPC_PSERIES && !CONFIG_PPC_POWERNV:
powerpc64le-pc-linux-gnu-ld: arch/powerpc/platforms/pseries/pci.o: in function `pSeries_final_fixup':
pci.c:(.init.text+0x1b0): undefined reference to `pnv_npu2_init'
This commit therefore wraps that line in an ifdef, so that pseries
builds without powernv.
Fixes: 3be2df00e2 ("powerpc/pseries/npu: Enable platform support")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[mpe: Frob change log a bit to blame a different commit]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
WARN_ON() already contains an unlikely(), so it's not necessary to
wrap it into another.
Signed-off-by: Igor Stoppa <igor.stoppa@huawei.com>
Cc: Arseny Solokha <asolokha@kb.kras.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
GCC supports -mcpu=G4
This patch gives the opportunity to select ALTIVEC for this variant.
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On Power9 machines (64-bit Book3S), we can be running with either the
Hash table or Radix tree MMU enabled. So add some text to the __die()
output to tell us which is enabled, for the case where all you have is
the oops output and no other information.
Example output:
kernel BUG at drivers/misc/lkdtm/bugs.c:63!
Oops: Exception in kernel mode, sig: 5 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: kvm vmx_crypto binfmt_misc ip_tables x_tables
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The page size the kernel is built with is useful info when debugging a
crash, so add it to the output in __die().
Result looks like eg:
kernel BUG at drivers/misc/lkdtm/bugs.c:63!
Oops: Exception in kernel mode, sig: 5 [#1]
LE PAGE_SIZE=64K SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: vmx_crypto kvm binfmt_misc ip_tables
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Using pr_cont() risks having our output interleaved with other output
from other CPUs. Instead print everything in a single printk() call.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The Wii has POWER and EJECT buttons, which are connected through
normalization logic to the GPIO controller (the length of an assertion
of these signals is always the same, regardless of how long the user
pressed the buttons).
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The Hollywood GPIO controller is connected to the Hollywood PIC (&PIC1)
at IRQs 10 and 11; IRQ 10 for GPIO lines that are configured for access
by the PPC, 11 for GPIO lines that are configured for access by the
ARM926.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
TCE_KILL_INVAL_ALL has moved long ago but the comment was forgotted so
finish the move and remove the comment.
Fixes: 0bbcdb437d "powerpc/powernv/npu: TCE Kill helpers cleanup"
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This removes never used symbol - pnv_power9_force_smt4.
Note that we might still want to add stubs for:
void pnv_power9_force_smt4_catch(void);
void pnv_power9_force_smt4_release(void);
Fixes: 7672691a08 "powerpc/powernv: Provide a way to force a core into SMT4 mode"
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the ld documentation under Builtin Functions:
BLOCK(exp)
This is a synonym for ALIGN, for compatibility with older linker scripts.
Clang's linker (lld) doesn't know about BLOCK so remove this use of
it.
Suggested-by: George Rimar <grimar@accesssoftek.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
I wanted to test the virtex440-ml507 qemu machine and found that the
dtb for it was not built.
All powerpc dtbs are only built when CONFIG_OF_ALL_DTBS is set which
depend on COMPILE_TEST.
This patch enables building of the virtex dtbs when
CONFIG_XILINX_VIRTEX440_GENERIC_BOARD is enabled.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
[mpe: Put both targets on a single line]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
ipic_set_highest_priority(), ipic_enable_mcp() and ipic_disable_mcp()
are unused. This patch drops them.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The header search path -I. in kernel Makefiles is very suspicious;
it allows the compiler to search for headers in the top of $(srctree),
where obviously no header file exists.
-Iinclude/math-emu seems unnecessary because all files include headers
in the form of #include <math-emu/...>.
I was able to build without these header search paths.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The same path -Iarch/$(ARCH) is passed to KBUILD_CPPFLAGS,
KBUILD_AFLAGS, and KBUILD_CFLAGS.
As you see in scripts/Makefile.lib, KBUILD_CPPFLAGS is passed
to c_flags and a_flags as well.
Passing it to KBUILD_CPPFLAGS is enough.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The header search path -I. in kernel Makefiles is very suspicious;
it allows the compiler to search for headers in the top of $(srctree),
where obviously no header file exists.
Commit 46f43c6ee0 ("KVM: powerpc: convert marker probes to event
trace") first added these options, but they are completely useless.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.
Generated by: scripts/coccinelle/api/debugfs/debugfs_simple_attr.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
arch_early_irq_init() does nothing different than the weak
arch_early_irq_init() in kernel/softirq.c
Fixes: 089fb442f3 ("powerpc: Use ARCH_IRQ_INIT_FLAGS")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use a CONSOLE_LOGLEVEL_DEBUG macro for console_loglevel rather
than a naked number.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
My recent commit to fix the printf warnings in ocm.c got the format
specifier wrong, because I copied it from the documentation without
realising the square brackets are not meant as literals.
This results in the address being suffixed with a literal "[p]".
Actually tested this time:
# cat info /sys/kernel/debug/ppc4xx_ocm
PhysAddr : 0x0000000400040000
...
NC.PhysAddr : 0x0000000400040000
...
C.PhysAddr : 0x0000000000000000
Fixes: 52b88fa1e8 ("powerpc/4xx/ocm: Fix phys_addr_t printf warnings")
Reported-by: Christian Lamparter <chunkeey@gmail.com>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With a recent change around IOMMU group, a system with an opencapi
adapter is no longer booting and we get a kernel oops:
BUG: Kernel NULL pointer dereference at 0x00000028
Faulting instruction address: 0xc0000000000aa38c
...
NIP pnv_try_setup_npu_table_group+0x1c/0x1a0
LR pnv_pci_ioda_fixup+0x1f8/0x660
Call Trace:
pnv_try_setup_npu_table_group+0x60/0x
pnv_pci_ioda_fixup+0x20c/0x660
pcibios_resource_survey+0x2c8/0x31c
pcibios_init+0xb0/0xe4
do_one_initcall+0x64/0x264
kernel_init_freeable+0x36c/0x468
kernel_init+0x2c/0x148
ret_from_kernel_thread+0x5c/0x68
An opencapi device is using a device PE, so the current code breaks
because pe->pbus is not defined.
More generally, there's no need to define an IOMMU group for opencapi,
as the device sends real addresses directly (admittedly, the
virtualization story is yet to be written). So let's fix it by
skipping the IOMMU group setup for opencapi PHBs.
Fixes: 0bd971676e ("powerpc/powernv/npu: Add compound IOMMU groups")
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit e1c3743e1a ("powerpc/tm: Set MSR[TS] just prior to recheckpoint")
moved a code block around and this block uses a 'msr' variable outside of
the CONFIG_PPC_TRANSACTIONAL_MEM, however the 'msr' variable is declared
inside a CONFIG_PPC_TRANSACTIONAL_MEM block, causing a possible error when
CONFIG_PPC_TRANSACTION_MEM is not defined.
error: 'msr' undeclared (first use in this function)
This is not causing a compilation error in the mainline kernel, because
'msr' is being used as an argument of MSR_TM_ACTIVE(), which is defined as
the following when CONFIG_PPC_TRANSACTIONAL_MEM is *not* set:
#define MSR_TM_ACTIVE(x) 0
This patch just fixes this issue avoiding the 'msr' variable usage outside
the CONFIG_PPC_TRANSACTIONAL_MEM block, avoiding trusting in the
MSR_TM_ACTIVE() definition.
Cc: stable@vger.kernel.org
Reported-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de>
Fixes: e1c3743e1a ("powerpc/tm: Set MSR[TS] just prior to recheckpoint")
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 8c8c10b90d ("powerpc/8xx: fix handling of early NULL pointer
dereference") moved the loading of r6 earlier in the code. As some
functions are called inbetween, r6 needs to be loaded again with the
address of swapper_pg_dir in order to set PTE pointers for
the Abatron BDI.
Fixes: 8c8c10b90d ("powerpc/8xx: fix handling of early NULL pointer dereference")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is a typo so we accidentally allocate enough memory for a pointer
when we wanted to allocate enough for a struct.
Fixes: 0bd971676e ("powerpc/powernv/npu: Add compound IOMMU groups")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
On each sample, Monitor Mode Control Register A (MMCRA) content is
saved in pt_regs. MMCRA does not have a entry as-is in the pt_regs but
instead, MMCRA content is saved in the "dsisr" register of pt_regs.
Patch adds another entry to the perf_regs structure to include the
"MMCRA" printing which internally maps to the "dsisr" of pt_regs.
It also check for the MMCRA availability in the platform and present
value accordingly
mpe: This was the 2nd patch in a series with commit 333804dc3b
("powerpc/perf: Update perf_regs structure to include SIER") but I
accidentally only merged the 1st patch, so merge this one now.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that Kbuild automatically creates asm-generic wrappers for missing
mandatory headers, it is redundant to list the same headers in
generic-y and mandatory-y.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
These comments are leftovers of commit fcc8487d47 ("uapi: export all
headers under uapi directories").
Prior to that commit, exported headers must be explicitly added to
header-y. Now, all headers under the uapi/ directories are exported.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, CONFIG_JUMP_LABEL just means "I _want_ to use jump label".
The jump label is controlled by HAVE_JUMP_LABEL, which is defined
like this:
#if defined(CC_HAVE_ASM_GOTO) && defined(CONFIG_JUMP_LABEL)
# define HAVE_JUMP_LABEL
#endif
We can improve this by testing 'asm goto' support in Kconfig, then
make JUMP_LABEL depend on CC_HAS_ASM_GOTO.
Ugly #ifdef HAVE_JUMP_LABEL will go away, and CONFIG_JUMP_LABEL will
match to the real kernel capability.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
A fix for the recent access_ok() change, which broke the build. We recently
added a use of type in order to squash a warning elsewhere about type being
unused.
A handful of other minor build fixes, and one defconfig update.
Thanks to:
Christian Lamparter, Christophe Leroy, Diana Craciun, Mathieu Malaterre.
-----BEGIN PGP SIGNATURE-----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=0vml
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A fix for the recent access_ok() change, which broke the build. We
recently added a use of type in order to squash a warning elsewhere
about type being unused.
A handful of other minor build fixes, and one defconfig update.
Thanks to: Christian Lamparter, Christophe Leroy, Diana Craciun,
Mathieu Malaterre"
* tag 'powerpc-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Drop use of 'type' from access_ok()
KVM: PPC: Book3S HV: radix: Fix uninitialized var build error
powerpc/configs: Add PPC4xx_OCM to ppc40x_defconfig
powerpc/4xx/ocm: Fix phys_addr_t printf warnings
powerpc/4xx/ocm: Fix compilation error due to PAGE_KERNEL usage
powerpc/fsl: Fixed warning: orphan section `__btb_flush_fixup'
Merge more updates from Andrew Morton:
- procfs updates
- various misc bits
- lib/ updates
- epoll updates
- autofs
- fatfs
- a few more MM bits
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (58 commits)
mm/page_io.c: fix polled swap page in
checkpatch: add Co-developed-by to signature tags
docs: fix Co-Developed-by docs
drivers/base/platform.c: kmemleak ignore a known leak
fs: don't open code lru_to_page()
fs/: remove caller signal_pending branch predictions
mm/: remove caller signal_pending branch predictions
arch/arc/mm/fault.c: remove caller signal_pending_branch predictions
kernel/sched/: remove caller signal_pending branch predictions
kernel/locking/mutex.c: remove caller signal_pending branch predictions
mm: select HAVE_MOVE_PMD on x86 for faster mremap
mm: speed up mremap by 20x on large regions
mm: treewide: remove unused address argument from pte_alloc functions
initramfs: cleanup incomplete rootfs
scripts/gdb: fix lx-version string output
kernel/kcov.c: mark write_comp_data() as notrace
kernel/sysctl: add panic_print into sysctl
panic: add options to print system info when panic happens
bfs: extra sanity checking and static inode bitmap
exec: separate MM_ANONPAGES and RLIMIT_STACK accounting
...
Patch series "Add support for fast mremap".
This series speeds up the mremap(2) syscall by copying page tables at
the PMD level even for non-THP systems. There is concern that the extra
'address' argument that mremap passes to pte_alloc may do something
subtle architecture related in the future that may make the scheme not
work. Also we find that there is no point in passing the 'address' to
pte_alloc since its unused. This patch therefore removes this argument
tree-wide resulting in a nice negative diff as well. Also ensuring
along the way that the enabled architectures do not do anything funky
with the 'address' argument that goes unnoticed by the optimization.
Build and boot tested on x86-64. Build tested on arm64. The config
enablement patch for arm64 will be posted in the future after more
testing.
The changes were obtained by applying the following Coccinelle script.
(thanks Julia for answering all Coccinelle questions!).
Following fix ups were done manually:
* Removal of address argument from pte_fragment_alloc
* Removal of pte_alloc_one_fast definitions from m68k and microblaze.
// Options: --include-headers --no-includes
// Note: I split the 'identifier fn' line, so if you are manually
// running it, please unsplit it so it runs for you.
virtual patch
@pte_alloc_func_def depends on patch exists@
identifier E2;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
type T2;
@@
fn(...
- , T2 E2
)
{ ... }
@pte_alloc_func_proto_noarg depends on patch exists@
type T1, T2, T3, T4;
identifier fn =~ "^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
(
- T3 fn(T1, T2);
+ T3 fn(T1);
|
- T3 fn(T1, T2, T4);
+ T3 fn(T1, T2);
)
@pte_alloc_func_proto depends on patch exists@
identifier E1, E2, E4;
type T1, T2, T3, T4;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
(
- T3 fn(T1 E1, T2 E2);
+ T3 fn(T1 E1);
|
- T3 fn(T1 E1, T2 E2, T4 E4);
+ T3 fn(T1 E1, T2 E2);
)
@pte_alloc_func_call depends on patch exists@
expression E2;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
fn(...
-, E2
)
@pte_alloc_macro depends on patch exists@
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
identifier a, b, c;
expression e;
position p;
@@
(
- #define fn(a, b, c) e
+ #define fn(a, b) e
|
- #define fn(a, b) e
+ #define fn(a) e
)
Link: http://lkml.kernel.org/r/20181108181201.88826-2-joelaf@google.com
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Suggested-by: Kirill A. Shutemov <kirill@shutemov.name>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: William Kucharski <william.kucharski@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These two architectures actually had an intentional use of the 'type'
argument to access_ok() just to avoid warnings.
I had actually noticed the powerpc one, but forgot to then fix it up.
And I missed the sparc32 case entirely.
This is hopefully all of it.
Reported-by: Mathieu Malaterre <malat@debian.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 96d4f267e4 ("Remove 'type' argument from access_ok() function")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit 05a4ab8239 ("powerpc/uaccess: fix warning/error with
access_ok()") an attempt was made to remove a warning by referencing
the variable `type`. However in commit 96d4f267e4 ("Remove 'type'
argument from access_ok() function") the variable `type` has been
removed, breaking the build:
arch/powerpc/include/asm/uaccess.h:66:32: error: ‘type’ undeclared (first use in this function)
This essentially reverts commit 05a4ab8239 ("powerpc/uaccess: fix
warning/error with access_ok()") to fix the error.
Fixes: 96d4f267e4 ("Remove 'type' argument from access_ok() function")
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[mpe: Reword change log slightly.]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Including (in no particular order):
- Page table code for AMD IOMMU now supports large pages where
smaller page-sizes were mapped before. VFIO had to work around
that in the past and I included a patch to remove it (acked by
Alex Williamson)
- Patches to unmodularize a couple of IOMMU drivers that would
never work as modules anyway.
- Work to unify the the iommu-related pointers in
'struct device' into one pointer. This work is not finished
yet, but will probably be in the next cycle.
- NUMA aware allocation in iommu-dma code
- Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver
- Scalable mode support for the Intel VT-d driver
- PM runtime improvements for the ARM-SMMU driver
- Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom
- Various smaller fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=DT9A
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- Page table code for AMD IOMMU now supports large pages where smaller
page-sizes were mapped before. VFIO had to work around that in the
past and I included a patch to remove it (acked by Alex Williamson)
- Patches to unmodularize a couple of IOMMU drivers that would never
work as modules anyway.
- Work to unify the the iommu-related pointers in 'struct device' into
one pointer. This work is not finished yet, but will probably be in
the next cycle.
- NUMA aware allocation in iommu-dma code
- Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver
- Scalable mode support for the Intel VT-d driver
- PM runtime improvements for the ARM-SMMU driver
- Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom
- Various smaller fixes and improvements
* tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (78 commits)
iommu: Check for iommu_ops == NULL in iommu_probe_device()
ACPI/IORT: Don't call iommu_ops->add_device directly
iommu/of: Don't call iommu_ops->add_device directly
iommu: Consolitate ->add/remove_device() calls
iommu/sysfs: Rename iommu_release_device()
dmaengine: sh: rcar-dmac: Use device_iommu_mapped()
xhci: Use device_iommu_mapped()
powerpc/iommu: Use device_iommu_mapped()
ACPI/IORT: Use device_iommu_mapped()
iommu/of: Use device_iommu_mapped()
driver core: Introduce device_iommu_mapped() function
iommu/tegra: Use helper functions to access dev->iommu_fwspec
iommu/qcom: Use helper functions to access dev->iommu_fwspec
iommu/of: Use helper functions to access dev->iommu_fwspec
iommu/mediatek: Use helper functions to access dev->iommu_fwspec
iommu/ipmmu-vmsa: Use helper functions to access dev->iommu_fwspec
iommu/dma: Use helper functions to access dev->iommu_fwspec
iommu/arm-smmu: Use helper functions to access dev->iommu_fwspec
ACPI/IORT: Use helper functions to access dev->iommu_fwspec
iommu: Introduce wrappers around dev->iommu_fwspec
...
Mostly clean ups although whilst Doug's was chasing down a odd
lockdep warning he also did some work to improved debugger resilience
when some CPUs fail to respond to the round up request.
The main changes are:
* Fixing a lockdep warning on architectures that cannot use an NMI for
the round up plus related changes to make CPU round up and all CPU
backtrace more resilient.
* Constify the arch ops tables
* A couple of other small clean ups
Two of the three patchsets here include changes that spill over into
arch/. Changes in the arch space are relatively narrow in scope
(and directly related to kgdb). Didn't get comprehensive acks but
all impacted maintainers were Cc:ed in good time.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
-----BEGIN PGP SIGNATURE-----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=Aqlc
-----END PGP SIGNATURE-----
Merge tag 'kgdb-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux
Pull kgdb updates from Daniel Thompson:
"Mostly clean ups although while Doug's was chasing down a odd lockdep
warning he also did some work to improved debugger resilience when
some CPUs fail to respond to the round up request.
The main changes are:
- Fixing a lockdep warning on architectures that cannot use an NMI
for the round up plus related changes to make CPU round up and all
CPU backtrace more resilient.
- Constify the arch ops tables
- A couple of other small clean ups
Two of the three patchsets here include changes that spill over into
arch/. Changes in the arch space are relatively narrow in scope (and
directly related to kgdb). Didn't get comprehensive acks but all
impacted maintainers were Cc:ed in good time"
* tag 'kgdb-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux:
kgdb/treewide: constify struct kgdb_arch arch_kgdb_ops
mips/kgdb: prepare arch_kgdb_ops for constness
kdb: use bool for binary state indicators
kdb: Don't back trace on a cpu that didn't round up
kgdb: Don't round up a CPU that failed rounding up before
kgdb: Fix kgdb_roundup_cpus() for arches who used smp_call_function()
kgdb: Remove irq flags from roundup
- Rework of the kprobe/uprobe and synthetic events to consolidate all
the dynamic event code. This will make changes in the future easier.
- Partial rewrite of the function graph tracing infrastructure.
This will allow for multiple users of hooking onto functions
to get the callback (return) of the function. This is the ground
work for having kprobes and function graph tracer using one code base.
- Clean up of the histogram code that will facilitate adding more
features to the histograms in the future.
- Addition of str_has_prefix() and a few use cases. There currently
is a similar function strstart() that is used in a few places, but
only returns a bool and not a length. These instances will be
removed in the future to use str_has_prefix() instead.
- A few other various clean ups as well.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXCawlBQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qhbcAQCFeT0fWWTUxofBQz5jqsHaRnVg21+9
X4sTldYRYEn4YgEAmWOyiwq7zvrsAu4ZwkNBMeqxn3tVymYHiGOGe3Y4BAw=
=u96o
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- Rework of the kprobe/uprobe and synthetic events to consolidate all
the dynamic event code. This will make changes in the future easier.
- Partial rewrite of the function graph tracing infrastructure. This
will allow for multiple users of hooking onto functions to get the
callback (return) of the function. This is the ground work for having
kprobes and function graph tracer using one code base.
- Clean up of the histogram code that will facilitate adding more
features to the histograms in the future.
- Addition of str_has_prefix() and a few use cases. There currently is
a similar function strstart() that is used in a few places, but only
returns a bool and not a length. These instances will be removed in
the future to use str_has_prefix() instead.
- A few other various clean ups as well.
* tag 'trace-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (57 commits)
tracing: Use the return of str_has_prefix() to remove open coded numbers
tracing: Have the historgram use the result of str_has_prefix() for len of prefix
tracing: Use str_has_prefix() instead of using fixed sizes
tracing: Use str_has_prefix() helper for histogram code
string.h: Add str_has_prefix() helper function
tracing: Make function ‘ftrace_exports’ static
tracing: Simplify printf'ing in seq_print_sym
tracing: Avoid -Wformat-nonliteral warning
tracing: Merge seq_print_sym_short() and seq_print_sym_offset()
tracing: Add hist trigger comments for variable-related fields
tracing: Remove hist trigger synth_var_refs
tracing: Use hist trigger's var_ref array to destroy var_refs
tracing: Remove open-coding of hist trigger var_ref management
tracing: Use var_refs[] for hist trigger reference checking
tracing: Change strlen to sizeof for hist trigger static strings
tracing: Remove unnecessary hist trigger struct field
tracing: Fix ftrace_graph_get_ret_stack() to use task and not current
seq_buf: Use size_t for len in seq_buf_puts()
seq_buf: Make seq_buf_puts() null-terminate the buffer
arm64: Use ftrace_graph_get_ret_stack() instead of curr_ret_stack
...
checkpatch.pl reports the following:
WARNING: struct kgdb_arch should normally be const
#28: FILE: arch/mips/kernel/kgdb.c:397:
+struct kgdb_arch arch_kgdb_ops = {
This report makes sense, as all other ops struct, this
one should also be const. This patch does the change.
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: x86@kernel.org
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
When I had lockdep turned on and dropped into kgdb I got a nice splat
on my system. Specifically it hit:
DEBUG_LOCKS_WARN_ON(current->hardirq_context)
Specifically it looked like this:
sysrq: SysRq : DEBUG
------------[ cut here ]------------
DEBUG_LOCKS_WARN_ON(current->hardirq_context)
WARNING: CPU: 0 PID: 0 at .../kernel/locking/lockdep.c:2875 lockdep_hardirqs_on+0xf0/0x160
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.19.0 #27
pstate: 604003c9 (nZCv DAIF +PAN -UAO)
pc : lockdep_hardirqs_on+0xf0/0x160
...
Call trace:
lockdep_hardirqs_on+0xf0/0x160
trace_hardirqs_on+0x188/0x1ac
kgdb_roundup_cpus+0x14/0x3c
kgdb_cpu_enter+0x53c/0x5cc
kgdb_handle_exception+0x180/0x1d4
kgdb_compiled_brk_fn+0x30/0x3c
brk_handler+0x134/0x178
do_debug_exception+0xfc/0x178
el1_dbg+0x18/0x78
kgdb_breakpoint+0x34/0x58
sysrq_handle_dbg+0x54/0x5c
__handle_sysrq+0x114/0x21c
handle_sysrq+0x30/0x3c
qcom_geni_serial_isr+0x2dc/0x30c
...
...
irq event stamp: ...45
hardirqs last enabled at (...44): [...] __do_softirq+0xd8/0x4e4
hardirqs last disabled at (...45): [...] el1_irq+0x74/0x130
softirqs last enabled at (...42): [...] _local_bh_enable+0x2c/0x34
softirqs last disabled at (...43): [...] irq_exit+0xa8/0x100
---[ end trace adf21f830c46e638 ]---
Looking closely at it, it seems like a really bad idea to be calling
local_irq_enable() in kgdb_roundup_cpus(). If nothing else that seems
like it could violate spinlock semantics and cause a deadlock.
Instead, let's use a private csd alongside
smp_call_function_single_async() to round up the other CPUs. Using
smp_call_function_single_async() doesn't require interrupts to be
enabled so we can remove the offending bit of code.
In order to avoid duplicating this across all the architectures that
use the default kgdb_roundup_cpus(), we'll add a "weak" implementation
to debug_core.c.
Looking at all the people who previously had copies of this code,
there were a few variants. I've attempted to keep the variants
working like they used to. Specifically:
* For arch/arc we passed NULL to kgdb_nmicallback() instead of
get_irq_regs().
* For arch/mips there was a bit of extra code around
kgdb_nmicallback()
NOTE: In this patch we will still get into trouble if we try to round
up a CPU that failed to round up before. We'll try to round it up
again and potentially hang when we try to grab the csd lock. That's
not new behavior but we'll still try to do better in a future patch.
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
The function kgdb_roundup_cpus() was passed a parameter that was
documented as:
> the flags that will be used when restoring the interrupts. There is
> local_irq_save() call before kgdb_roundup_cpus().
Nobody used those flags. Anyone who wanted to temporarily turn on
interrupts just did local_irq_enable() and local_irq_disable() without
looking at them. So we can definitely remove the flags.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Old GCCs (4.6.3 at least), aren't able to follow the logic in
__kvmhv_copy_tofrom_guest_radix() and warn that old_pid is used
uninitialized:
arch/powerpc/kvm/book3s_64_mmu_radix.c:75:3: error: 'old_pid' may be
used uninitialized in this function
The logic is OK, we only use old_pid if quadrant == 1, and in that
case it has definitely be initialised, eg:
if (quadrant == 1) {
old_pid = mfspr(SPRN_PID);
...
if (quadrant == 1 && pid != old_pid)
mtspr(SPRN_PID, old_pid);
Annotate it to fix the error.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There was recently a compilation break to this driver, but we didn't
notice because none of our defconfigs have it enabled. Fix that.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently the code produces several warnings, eg:
arch/powerpc/platforms/4xx/ocm.c:240:38: error: format '%llx'
expects argument of type 'long long unsigned int', but argument 3
has type 'phys_addr_t {aka unsigned int}'
seq_printf(m, "PhysAddr : 0x%llx\n", ocm->phys);
~~~^ ~~~~~~~~~
Fix it by using the special %pa[p] format for printing phys_addr_t.
Note we need to pass the value by reference for the special specifier
to work.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fixed the following build warning:
powerpc-linux-gnu-ld: warning: orphan section `__btb_flush_fixup' from
`arch/powerpc/kernel/head_44x.o' being placed in section
`__btb_flush_fixup'.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Consolidation of bus (PCI, PCMCIA, EISA, RapidIO) config entries
by Christoph Hellwig.
Currently, every architecture that wants to provide common peripheral
busses needs to add some boilerplate code and include the right Kconfig
files. This series instead just selects the presence (when needed) and
then handles everything in the bus-specific Kconfig file under drivers/.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJcJilwAAoJED2LAQed4NsGt1YP/RMTEUqbCSwS/CnTLrE+aVTC
O2aWwB80ZlVwpeBbHLW5/M88OvOev0UaCr+gyzgpFRl5ITzS7Jevb8VbpGzblbH7
bFxIEyZFGQiy9oEWw3Lfu9JRSsLm3jNo7hkmdBSn2Rw3KkEd/YF7K3q9GuA7BpCS
ZxAirebvEpr4KYEzkuc57NqCYx2Tc8G+JWr5D7pZCFaq9vxYt3TddGqw/c7iQVSQ
1Og1809IdhGyCSlA/ExfaqaBMaJHMRAOHX5GgkqZw1EbFcizUFhAAsKCrGL5nBtX
NiWF9jhgHR1M+L69jfctOstrmGQD2KicNgWQf1aS5RQkPfjuqIKGT/i9g6J1pVyX
TaW1J36Hcl8PpsKoPBnnrixd1T41O3/PuqtEJRm7LCBYOQiwS9sEmLO09RDRjER8
SPAAyvkhE8oq+0RHiTYN4tm8dyJc1djZ5wzgLnwFPAnU6SR+mbN02RzBMsYZXD+x
RNbBSGBRJFQDBw6Rn+ktcIQvcKYmUqe1k1YNHMy6kG3QqvhBaDy+8PA/YjIKPQYQ
B/NNUAMEJMys1OQrRL2UDXb2ysaCpzwMmlrBW2IwYsQrX5OwbPkNuQ5Mbe1Lr+mc
4NXR+HubvojsHaAby+OhFbrUX2Jcz3wqYj7aannb9sMRmw0VJXV5dPYUqje3ZhPS
P2AovKT8O9nWsEttqER5
=WxId
-----END PGP SIGNATURE-----
Merge tag 'kconfig-v4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kconfig file consolidation from Masahiro Yamada:
"Consolidation of bus (PCI, PCMCIA, EISA, RapidIO) config entries by
Christoph Hellwig.
Currently, every architecture that wants to provide common peripheral
busses needs to add some boilerplate code and include the right
Kconfig files. This series instead just selects the presence (when
needed) and then handles everything in the bus-specific Kconfig file
under drivers/"
* tag 'kconfig-v4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
pcmcia: remove per-arch PCMCIA config entry
eisa: consolidate EISA Kconfig entry in drivers/eisa
rapidio: consolidate RAPIDIO config entry in drivers/rapidio
pcmcia: allow PCMCIA support independent of the architecture
PCI: consolidate the PCI_SYSCALL symbol
PCI: consolidate the PCI_DOMAINS and PCI_DOMAINS_GENERIC config options
PCI: consolidate PCI config entry in drivers/pci
MIPS: remove the HT_PCI config option
- support -y option for merge_config.sh to avoid downgrading =y to =m
- remove S_OTHER symbol type, and touch include/config/*.h files correctly
- fix file name and line number in lexer warnings
- fix memory leak when EOF is encountered in quotation
- resolve all shift/reduce conflicts of the parser
- warn no new line at end of file
- make 'source' statement more strict to take only string literal
- rewrite the lexer and remove the keyword lookup table
- convert to SPDX License Identifier
- compile C files independently instead of including them from zconf.y
- fix various warnings of gconfig
- misc cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=r3Fl
-----END PGP SIGNATURE-----
Merge tag 'kconfig-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kconfig updates from Masahiro Yamada:
- support -y option for merge_config.sh to avoid downgrading =y to =m
- remove S_OTHER symbol type, and touch include/config/*.h files correctly
- fix file name and line number in lexer warnings
- fix memory leak when EOF is encountered in quotation
- resolve all shift/reduce conflicts of the parser
- warn no new line at end of file
- make 'source' statement more strict to take only string literal
- rewrite the lexer and remove the keyword lookup table
- convert to SPDX License Identifier
- compile C files independently instead of including them from zconf.y
- fix various warnings of gconfig
- misc cleanups
* tag 'kconfig-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (39 commits)
kconfig: surround dbg_sym_flags with #ifdef DEBUG to fix gconf warning
kconfig: split images.c out of qconf.cc/gconf.c to fix gconf warnings
kconfig: add static qualifiers to fix gconf warnings
kconfig: split the lexer out of zconf.y
kconfig: split some C files out of zconf.y
kconfig: convert to SPDX License Identifier
kconfig: remove keyword lookup table entirely
kconfig: update current_pos in the second lexer
kconfig: switch to ASSIGN_VAL state in the second lexer
kconfig: stop associating kconf_id with yylval
kconfig: refactor end token rules
kconfig: stop supporting '.' and '/' in unquoted words
treewide: surround Kconfig file paths with double quotes
microblaze: surround string default in Kconfig with double quotes
kconfig: use T_WORD instead of T_VARIABLE for variables
kconfig: use specific tokens instead of T_ASSIGN for assignments
kconfig: refactor scanning and parsing "option" properties
kconfig: use distinct tokens for type and default properties
kconfig: remove redundant token defines
kconfig: rename depends_list to comment_option_list
...
Pull Devicetree updates from Rob Herring:
"The biggest highlight here is the start of using json-schema for DT
bindings. Being able to validate bindings has been discussed for years
with little progress.
- Initial support for DT bindings using json-schema language. This is
the start of converting DT bindings from free-form text to a
structured format.
- Reworking of initrd address initialization. This moves to using the
phys address instead of virt addr in the DT parsing code. This
rework was motivated by CONFIG_DEV_BLK_INITRD causing unnecessary
rebuilding of lots of files.
- Fix stale phandle entries in phandle cache
- DT overlay validation improvements. This exposed several memory
leak bugs which have been fixed.
- Use node name and device_type helper functions in DT code
- Last remaining conversions to using %pOFn printk specifier instead
of device_node.name directly
- Create new common RTC binding doc and move all trivial RTC devices
out of trivial-devices.txt.
- New bindings for Freescale MAG3110 magnetometer, Cadence Sierra
PHY, and Xen shared memory
- Update dtc to upstream version v1.4.7-57-gf267e674d145"
* tag 'devicetree-for-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (68 commits)
of: __of_detach_node() - remove node from phandle cache
of: of_node_get()/of_node_put() nodes held in phandle cache
gpio-omap.txt: add reg and interrupts properties
dt-bindings: mrvl,intc: fix a trivial typo
dt-bindings: iio: magnetometer: add dt-bindings for freescale mag3110
dt-bindings: Convert trivial-devices.txt to json-schema
dt-bindings: arm: mrvl: amend Browstone compatible string
dt-bindings: arm: Convert Tegra board/soc bindings to json-schema
dt-bindings: arm: Convert ZTE board/soc bindings to json-schema
dt-bindings: arm: Add missing Xilinx boards
dt-bindings: arm: Convert Xilinx board/soc bindings to json-schema
dt-bindings: arm: Convert VIA board/soc bindings to json-schema
dt-bindings: arm: Convert ST STi board/soc bindings to json-schema
dt-bindings: arm: Convert SPEAr board/soc bindings to json-schema
dt-bindings: arm: Convert CSR SiRF board/soc bindings to json-schema
dt-bindings: arm: Convert QCom board/soc bindings to json-schema
dt-bindings: arm: Convert TI nspire board/soc bindings to json-schema
dt-bindings: arm: Convert TI davinci board/soc bindings to json-schema
dt-bindings: arm: Convert Calxeda board/soc bindings to json-schema
dt-bindings: arm: Convert Altera board/soc bindings to json-schema
...
Merge misc updates from Andrew Morton:
- large KASAN update to use arm's "software tag-based mode"
- a few misc things
- sh updates
- ocfs2 updates
- just about all of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (167 commits)
kernel/fork.c: mark 'stack_vm_area' with __maybe_unused
memcg, oom: notify on oom killer invocation from the charge path
mm, swap: fix swapoff with KSM pages
include/linux/gfp.h: fix typo
mm/hmm: fix memremap.h, move dev_page_fault_t callback to hmm
hugetlbfs: Use i_mmap_rwsem to fix page fault/truncate race
hugetlbfs: use i_mmap_rwsem for more pmd sharing synchronization
memory_hotplug: add missing newlines to debugging output
mm: remove __hugepage_set_anon_rmap()
include/linux/vmstat.h: remove unused page state adjustment macro
mm/page_alloc.c: allow error injection
mm: migrate: drop unused argument of migrate_page_move_mapping()
blkdev: avoid migration stalls for blkdev pages
mm: migrate: provide buffer_migrate_page_norefs()
mm: migrate: move migrate_page_lock_buffers()
mm: migrate: lock buffers before migrate_page_move_mapping()
mm: migration: factor out code to compute expected number of page references
mm, page_alloc: enable pcpu_drain with zone capability
kmemleak: add config to select auto scan
mm/page_alloc.c: don't call kasan_free_pages() at deferred mem init
...
A huge update this time, but a lot of that is just consolidating or
removing code:
- provide a common DMA_MAPPING_ERROR definition and avoid indirect
calls for dma_map_* error checking
- use direct calls for the DMA direct mapping case, avoiding huge
retpoline overhead for high performance workloads
- merge the swiotlb dma_map_ops into dma-direct
- provide a generic remapping DMA consistent allocator for architectures
that have devices that perform DMA that is not cache coherent. Based
on the existing arm64 implementation and also used for csky now.
- improve the dma-debug infrastructure, including dynamic allocation
of entries (Robin Murphy)
- default to providing chaining scatterlist everywhere, with opt-outs
for the few architectures (alpha, parisc, most arm32 variants) that
can't cope with it
- misc sparc32 dma-related cleanups
- remove the dma_mark_clean arch hook used by swiotlb on ia64 and
replace it with the generic noncoherent infrastructure
- fix the return type of dma_set_max_seg_size (Niklas Söderlund)
- move the dummy dma ops for not DMA capable devices from arm64 to
common code (Robin Murphy)
- ensure dma_alloc_coherent returns zeroed memory to avoid kernel data
leaks through userspace. We already did this for most common
architectures, but this ensures we do it everywhere.
dma_zalloc_coherent has been deprecated and can hopefully be
removed after -rc1 with a coccinelle script.
-----BEGIN PGP SIGNATURE-----
iQI/BAABCgApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAlwctQgLHGhjaEBsc3Qu
ZGUACgkQD55TZVIEUYMxgQ//dBpAfS4/J76CdAbYry2zqgcOUU9hIrD6NHiEMWov
ltJxyvEl3LsUmIdEj3aCrYL9jZN0qsnCzn5BVj2c3jDIVgD64fAr7HDf/PbEEfKb
j6/GgEnVLPZV+sQMvhNA5jOzHrkseaqPa4/pNLFZ/l8jnuZ2d+btusDWJpMoVDer
TXVwtIfgeIu0gTygYOShLYXd5qptWKWsZEpbTZOO2sE6+x+ZJX7yQYUxYDTlcOIj
JWVO2l5QNHPc5T9o2at+6L5aNUvnZOxT79sWgyZLn0Kc+FagKAVwfLqUEl0v7foG
8k/xca5/8p3afB1DfrIrtplJqis7cVgdyGxriwuuoO8X4F0nPyWwpGmxsBhrWwwl
xTqC4UorEJ7QwoP6Azopk/vYI2QXIUBLjuCJCuFXZj9+2BGf4IfvBY1S2cLM9qLs
HMcxQonuXJii044KEFS96ePEuiT+igVINweIFBKWcgNCEG0UQtyL6RQ1U5297ipF
JiWZAqD+p9X52UdKS+oKfAiZEekMXn6Xyo97+YCiNpfOo0GP5eEcwhL+JpY4AiRq
apPXtsRy2o1s8yfjdraUIM2Mc2n62vFKb35oUbGCd/QO9piPrFQHl6T0HHcHk4YR
XrUXcHieFZBCYqh7ZVa4RL8Msq1wvGuTL4Dxl43mXdsMoUFRR6eSNWLoAV4IpOLZ
WgA=
=in72
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.21' of git://git.infradead.org/users/hch/dma-mapping
Pull DMA mapping updates from Christoph Hellwig:
"A huge update this time, but a lot of that is just consolidating or
removing code:
- provide a common DMA_MAPPING_ERROR definition and avoid indirect
calls for dma_map_* error checking
- use direct calls for the DMA direct mapping case, avoiding huge
retpoline overhead for high performance workloads
- merge the swiotlb dma_map_ops into dma-direct
- provide a generic remapping DMA consistent allocator for
architectures that have devices that perform DMA that is not cache
coherent. Based on the existing arm64 implementation and also used
for csky now.
- improve the dma-debug infrastructure, including dynamic allocation
of entries (Robin Murphy)
- default to providing chaining scatterlist everywhere, with opt-outs
for the few architectures (alpha, parisc, most arm32 variants) that
can't cope with it
- misc sparc32 dma-related cleanups
- remove the dma_mark_clean arch hook used by swiotlb on ia64 and
replace it with the generic noncoherent infrastructure
- fix the return type of dma_set_max_seg_size (Niklas Söderlund)
- move the dummy dma ops for not DMA capable devices from arm64 to
common code (Robin Murphy)
- ensure dma_alloc_coherent returns zeroed memory to avoid kernel
data leaks through userspace. We already did this for most common
architectures, but this ensures we do it everywhere.
dma_zalloc_coherent has been deprecated and can hopefully be
removed after -rc1 with a coccinelle script"
* tag 'dma-mapping-4.21' of git://git.infradead.org/users/hch/dma-mapping: (73 commits)
dma-mapping: fix inverted logic in dma_supported
dma-mapping: deprecate dma_zalloc_coherent
dma-mapping: zero memory returned from dma_alloc_*
sparc/iommu: fix ->map_sg return value
sparc/io-unit: fix ->map_sg return value
arm64: default to the direct mapping in get_arch_dma_ops
PCI: Remove unused attr variable in pci_dma_configure
ia64: only select ARCH_HAS_DMA_COHERENT_TO_PFN if swiotlb is enabled
dma-mapping: bypass indirect calls for dma-direct
vmd: use the proper dma_* APIs instead of direct methods calls
dma-direct: merge swiotlb_dma_ops into the dma_direct code
dma-direct: use dma_direct_map_page to implement dma_direct_map_sg
dma-direct: improve addressability error reporting
swiotlb: remove dma_mark_clean
swiotlb: remove SWIOTLB_MAP_ERROR
ACPI / scan: Refactor _CCA enforcement
dma-mapping: factor out dummy DMA ops
dma-mapping: always build the direct mapping code
dma-mapping: move dma_cache_sync out of line
dma-mapping: move various slow path functions out of line
...
Patch series "Do not touch pages in hot-remove path", v2.
This patchset aims for two things:
1) A better definition about offline and hot-remove stage
2) Solving bugs where we can access non-initialized pages
during hot-remove operations [2] [3].
This is achieved by moving all page/zone handling to the offline
stage, so we do not need to access pages when hot-removing memory.
[1] https://patchwork.kernel.org/cover/10691415/
[2] https://patchwork.kernel.org/patch/10547445/
[3] https://www.spinics.net/lists/linux-mm/msg161316.html
This patch (of 5):
This is a preparation for the following-up patches. The idea of passing
the nid is that it will allow us to get rid of the zone parameter
afterwards.
Link: http://lkml.kernel.org/r/20181127162005.15833-2-osalvador@suse.de
Signed-off-by: Oscar Salvador <osalvador@suse.de>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
totalram_pages and totalhigh_pages are made static inline function.
Main motivation was that managed_page_count_lock handling was complicating
things. It was discussed in length here,
https://lore.kernel.org/patchwork/patch/995739/#1181785 So it seemes
better to remove the lock and convert variables to atomic, with preventing
poteintial store-to-read tearing as a bonus.
[akpm@linux-foundation.org: coding style fixes]
Link: http://lkml.kernel.org/r/1542090790-21750-4-git-send-email-arunks@codeaurora.org
Signed-off-by: Arun KS <arunks@codeaurora.org>
Suggested-by: Michal Hocko <mhocko@suse.com>
Suggested-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reviewed-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) New ipset extensions for matching on destination MAC addresses, from
Stefano Brivio.
2) Add ipv4 ttl and tos, plus ipv6 flow label and hop limit offloads to
nfp driver. From Stefano Brivio.
3) Implement GRO for plain UDP sockets, from Paolo Abeni.
4) Lots of work from Michał Mirosław to eliminate the VLAN_TAG_PRESENT
bit so that we could support the entire vlan_tci value.
5) Rework the IPSEC policy lookups to better optimize more usecases,
from Florian Westphal.
6) Infrastructure changes eliminating direct manipulation of SKB lists
wherever possible, and to always use the appropriate SKB list
helpers. This work is still ongoing...
7) Lots of PHY driver and state machine improvements and
simplifications, from Heiner Kallweit.
8) Various TSO deferral refinements, from Eric Dumazet.
9) Add ntuple filter support to aquantia driver, from Dmitry Bogdanov.
10) Batch dropping of XDP packets in tuntap, from Jason Wang.
11) Lots of cleanups and improvements to the r8169 driver from Heiner
Kallweit, including support for ->xmit_more. This driver has been
getting some much needed love since he started working on it.
12) Lots of new forwarding selftests from Petr Machata.
13) Enable VXLAN learning in mlxsw driver, from Ido Schimmel.
14) Packed ring support for virtio, from Tiwei Bie.
15) Add new Aquantia AQtion USB driver, from Dmitry Bezrukov.
16) Add XDP support to dpaa2-eth driver, from Ioana Ciocoi Radulescu.
17) Implement coalescing on TCP backlog queue, from Eric Dumazet.
18) Implement carrier change in tun driver, from Nicolas Dichtel.
19) Support msg_zerocopy in UDP, from Willem de Bruijn.
20) Significantly improve garbage collection of neighbor objects when
the table has many PERMANENT entries, from David Ahern.
21) Remove egdev usage from nfp and mlx5, and remove the facility
completely from the tree as it no longer has any users. From Oz
Shlomo and others.
22) Add a NETDEV_PRE_CHANGEADDR so that drivers can veto the change and
therefore abort the operation before the commit phase (which is the
NETDEV_CHANGEADDR event). From Petr Machata.
23) Add indirect call wrappers to avoid retpoline overhead, and use them
in the GRO code paths. From Paolo Abeni.
24) Add support for netlink FDB get operations, from Roopa Prabhu.
25) Support bloom filter in mlxsw driver, from Nir Dotan.
26) Add SKB extension infrastructure. This consolidates the handling of
the auxiliary SKB data used by IPSEC and bridge netfilter, and is
designed to support the needs to MPTCP which could be integrated in
the future.
27) Lots of XDP TX optimizations in mlx5 from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1845 commits)
net: dccp: fix kernel crash on module load
drivers/net: appletalk/cops: remove redundant if statement and mask
bnx2x: Fix NULL pointer dereference in bnx2x_del_all_vlans() on some hw
net/net_namespace: Check the return value of register_pernet_subsys()
net/netlink_compat: Fix a missing check of nla_parse_nested
ieee802154: lowpan_header_create check must check daddr
net/mlx4_core: drop useless LIST_HEAD
mlxsw: spectrum: drop useless LIST_HEAD
net/mlx5e: drop useless LIST_HEAD
iptunnel: Set tun_flags in the iptunnel_metadata_reply from src
net/mlx5e: fix semicolon.cocci warnings
staging: octeon: fix build failure with XFRM enabled
net: Revert recent Spectre-v1 patches.
can: af_can: Fix Spectre v1 vulnerability
packet: validate address length if non-zero
nfc: af_nfc: Fix Spectre v1 vulnerability
phonet: af_phonet: Fix Spectre v1 vulnerability
net: core: Fix Spectre v1 vulnerability
net: minor cleanup in skb_ext_add()
net: drop the unused helper skb_ext_get()
...
Notable changes:
- Mitigations for Spectre v2 on some Freescale (NXP) CPUs.
- A large series adding support for pass-through of Nvidia V100 GPUs to guests
on Power9.
- Another large series to enable hardware assistance for TLB table walk on
MPC8xx CPUs.
- Some preparatory changes to our DMA code, to make way for further cleanups
from Christoph.
- Several fixes for our Transactional Memory handling discovered by fuzzing the
signal return path.
- Support for generating our system call table(s) from a text file like other
architectures.
- A fix to our page fault handler so that instead of generating a WARN_ON_ONCE,
user accesses of kernel addresses instead print a ratelimited and
appropriately scary warning.
- A cosmetic change to make our unhandled page fault messages more similar to
other arches and also more compact and informative.
- Freescale updates from Scott:
"Highlights include elimination of legacy clock bindings use from dts
files, an 83xx watchdog handler, fixes to old dts interrupt errors, and
some minor cleanup."
And many clean-ups, reworks and minor fixes etc.
Thanks to:
Alexandre Belloni, Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V,
Arnd Bergmann, Benjamin Herrenschmidt, Breno Leitao, Christian Lamparter,
Christophe Leroy, Christoph Hellwig, Daniel Axtens, Darren Stevens, David
Gibson, Diana Craciun, Dmitry V. Levin, Firoz Khan, Geert Uytterhoeven, Greg
Kurz, Gustavo Romero, Hari Bathini, Joel Stanley, Kees Cook, Madhavan
Srinivasan, Mahesh Salgaonkar, Markus Elfring, Mathieu Malaterre, Michal
Suchánek, Naveen N. Rao, Nick Desaulniers, Oliver O'Halloran, Paul Mackerras,
Ram Pai, Ravi Bangoria, Rob Herring, Russell Currey, Sabyasachi Gupta, Sam
Bobroff, Satheesh Rajendran, Scott Wood, Segher Boessenkool, Stephen Rothwell,
Tang Yuantian, Thiago Jung Bauermann, Yangtao Li, Yuantian Tang, Yue Haibing.
-----BEGIN PGP SIGNATURE-----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=cr6s
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- Mitigations for Spectre v2 on some Freescale (NXP) CPUs.
- A large series adding support for pass-through of Nvidia V100 GPUs
to guests on Power9.
- Another large series to enable hardware assistance for TLB table
walk on MPC8xx CPUs.
- Some preparatory changes to our DMA code, to make way for further
cleanups from Christoph.
- Several fixes for our Transactional Memory handling discovered by
fuzzing the signal return path.
- Support for generating our system call table(s) from a text file
like other architectures.
- A fix to our page fault handler so that instead of generating a
WARN_ON_ONCE, user accesses of kernel addresses instead print a
ratelimited and appropriately scary warning.
- A cosmetic change to make our unhandled page fault messages more
similar to other arches and also more compact and informative.
- Freescale updates from Scott:
"Highlights include elimination of legacy clock bindings use from
dts files, an 83xx watchdog handler, fixes to old dts interrupt
errors, and some minor cleanup."
And many clean-ups, reworks and minor fixes etc.
Thanks to: Alexandre Belloni, Alexey Kardashevskiy, Andrew Donnellan,
Aneesh Kumar K.V, Arnd Bergmann, Benjamin Herrenschmidt, Breno Leitao,
Christian Lamparter, Christophe Leroy, Christoph Hellwig, Daniel
Axtens, Darren Stevens, David Gibson, Diana Craciun, Dmitry V. Levin,
Firoz Khan, Geert Uytterhoeven, Greg Kurz, Gustavo Romero, Hari
Bathini, Joel Stanley, Kees Cook, Madhavan Srinivasan, Mahesh
Salgaonkar, Markus Elfring, Mathieu Malaterre, Michal Suchánek, Naveen
N. Rao, Nick Desaulniers, Oliver O'Halloran, Paul Mackerras, Ram Pai,
Ravi Bangoria, Rob Herring, Russell Currey, Sabyasachi Gupta, Sam
Bobroff, Satheesh Rajendran, Scott Wood, Segher Boessenkool, Stephen
Rothwell, Tang Yuantian, Thiago Jung Bauermann, Yangtao Li, Yuantian
Tang, Yue Haibing"
* tag 'powerpc-4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (201 commits)
Revert "powerpc/fsl_pci: simplify fsl_pci_dma_set_mask"
powerpc/zImage: Also check for stdout-path
powerpc: Fix HMIs on big-endian with CONFIG_RELOCATABLE=y
macintosh: Use of_node_name_{eq, prefix} for node name comparisons
ide: Use of_node_name_eq for node name comparisons
powerpc: Use of_node_name_eq for node name comparisons
powerpc/pseries/pmem: Convert to %pOFn instead of device_node.name
powerpc/mm: Remove very old comment in hash-4k.h
powerpc/pseries: Fix node leak in update_lmb_associativity_index()
powerpc/configs/85xx: Enable CONFIG_DEBUG_KERNEL
powerpc/dts/fsl: Fix dtc-flagged interrupt errors
clk: qoriq: add more compatibles strings
powerpc/fsl: Use new clockgen binding
powerpc/83xx: handle machine check caused by watchdog timer
powerpc/fsl-rio: fix spelling mistake "reserverd" -> "reserved"
powerpc/fsl_pci: simplify fsl_pci_dma_set_mask
arch/powerpc/fsl_rmu: Use dma_zalloc_coherent
vfio_pci: Add NVIDIA GV100GL [Tesla V100 SXM2] subdriver
vfio_pci: Allow regions to add own capabilities
vfio_pci: Allow mapping extra regions
...
Pull x86 build updates from Ingo Molnar:
- Resolve LLVM build bug by removing redundant GNU specific flag
- Remove obsolete -funit-at-a-time and -fno-unit-at-a-time use from x86
PowerPC and UM.
The UML change was seen and acked by UML maintainer Richard
Weinberger.
* 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/um/vdso: Drop implicit common-page-size linker flag
x86, powerpc: Remove -funit-at-a-time compiler option entirely
x86/um: Remove -fno-unit-at-a-time workaround for pre-4.0 GCC
Pull RCU updates from Ingo Molnar:
"The biggest RCU changes in this cycle were:
- Convert RCU's BUG_ON() and similar calls to WARN_ON() and similar.
- Replace calls of RCU-bh and RCU-sched update-side functions to
their vanilla RCU counterparts. This series is a step towards
complete removal of the RCU-bh and RCU-sched update-side functions.
( Note that some of these conversions are going upstream via their
respective maintainers. )
- Documentation updates, including a number of flavor-consolidation
updates from Joel Fernandes.
- Miscellaneous fixes.
- Automate generation of the initrd filesystem used for rcutorture
testing.
- Convert spin_is_locked() assertions to instead use lockdep.
( Note that some of these conversions are going upstream via their
respective maintainers. )
- SRCU updates, especially including a fix from Dennis Krein for a
bag-on-head-class bug.
- RCU torture-test updates"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (112 commits)
rcutorture: Don't do busted forward-progress testing
rcutorture: Use 100ms buckets for forward-progress callback histograms
rcutorture: Recover from OOM during forward-progress tests
rcutorture: Print forward-progress test age upon failure
rcutorture: Print time since GP end upon forward-progress failure
rcutorture: Print histogram of CB invocation at OOM time
rcutorture: Print GP age upon forward-progress failure
rcu: Print per-CPU callback counts for forward-progress failures
rcu: Account for nocb-CPU callback counts in RCU CPU stall warnings
rcutorture: Dump grace-period diagnostics upon forward-progress OOM
rcutorture: Prepare for asynchronous access to rcu_fwd_startat
torture: Remove unnecessary "ret" variables
rcutorture: Affinity forward-progress test to avoid housekeeping CPUs
rcutorture: Break up too-long rcu_torture_fwd_prog() function
rcutorture: Remove cbflood facility
torture: Bring any extra CPUs online during kernel startup
rcutorture: Add call_rcu() flooding forward-progress tests
rcutorture/formal: Replace synchronize_sched() with synchronize_rcu()
tools/kernel.h: Replace synchronize_sched() with synchronize_rcu()
net/decnet: Replace rcu_barrier_bh() with rcu_barrier()
...
single-stepping fixes, improved tracing, various timer and vGIC
fixes
* x86: Processor Tracing virtualization, STIBP support, some correctness fixes,
refactorings and splitting of vmx.c, use the Hyper-V range TLB flush hypercall,
reduce order of vcpu struct, WBNOINVD support, do not use -ftrace for __noclone
functions, nested guest support for PAUSE filtering on AMD, more Hyper-V
enlightenments (direct mode for synthetic timers)
* PPC: nested VFIO
* s390: bugfixes only this time
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJcH0vFAAoJEL/70l94x66Dw/wH/2FZp1YOM5OgiJzgqnXyDbyf
dNEfWo472MtNiLsuf+ZAfJojVIu9cv7wtBfXNzW+75XZDfh/J88geHWNSiZDm3Fe
aM4MOnGG0yF3hQrRQyEHe4IFhGFNERax8Ccv+OL44md9CjYrIrsGkRD08qwb+gNh
P8T/3wJEKwUcVHA/1VHEIM8MlirxNENc78p6JKd/C7zb0emjGavdIpWFUMr3SNfs
CemabhJUuwOYtwjRInyx1y34FzYwW3Ejuc9a9UoZ+COahUfkuxHE8u+EQS7vLVF6
2VGVu5SA0PqgmLlGhHthxLqVgQYo+dB22cRnsLtXlUChtVAq8q9uu5sKzvqEzuE=
=b4Jx
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- selftests improvements
- large PUD support for HugeTLB
- single-stepping fixes
- improved tracing
- various timer and vGIC fixes
x86:
- Processor Tracing virtualization
- STIBP support
- some correctness fixes
- refactorings and splitting of vmx.c
- use the Hyper-V range TLB flush hypercall
- reduce order of vcpu struct
- WBNOINVD support
- do not use -ftrace for __noclone functions
- nested guest support for PAUSE filtering on AMD
- more Hyper-V enlightenments (direct mode for synthetic timers)
PPC:
- nested VFIO
s390:
- bugfixes only this time"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (171 commits)
KVM: x86: Add CPUID support for new instruction WBNOINVD
kvm: selftests: ucall: fix exit mmio address guessing
Revert "compiler-gcc: disable -ftracer for __noclone functions"
KVM: VMX: Move VM-Enter + VM-Exit handling to non-inline sub-routines
KVM: VMX: Explicitly reference RCX as the vmx_vcpu pointer in asm blobs
KVM: x86: Use jmp to invoke kvm_spurious_fault() from .fixup
MAINTAINERS: Add arch/x86/kvm sub-directories to existing KVM/x86 entry
KVM/x86: Use SVM assembly instruction mnemonics instead of .byte streams
KVM/MMU: Flush tlb directly in the kvm_zap_gfn_range()
KVM/MMU: Flush tlb directly in kvm_set_pte_rmapp()
KVM/MMU: Move tlb flush in kvm_set_pte_rmapp() to kvm_mmu_notifier_change_pte()
KVM: Make kvm_set_spte_hva() return int
KVM: Replace old tlb flush function with new one to flush a specified range.
KVM/MMU: Add tlb flush with range helper function
KVM/VMX: Add hv tlb range flush support
x86/hyper-v: Add HvFlushGuestAddressList hypercall support
KVM: Add tlb_remote_flush_with_range callback in kvm_x86_ops
KVM: x86: Disable Intel PT when VMXON in L1 guest
KVM: x86: Set intercept for Intel PT MSRs read/write
KVM: x86: Implement Intel PT MSRs read/write emulation
...
In the end, we ended up with quite a lot more than I expected:
- Support for ARMv8.3 Pointer Authentication in userspace (CRIU and
kernel-side support to come later)
- Support for per-thread stack canaries, pending an update to GCC that
is currently undergoing review
- Support for kexec_file_load(), which permits secure boot of a kexec
payload but also happens to improve the performance of kexec
dramatically because we can avoid the sucky purgatory code from
userspace. Kdump will come later (requires updates to libfdt).
- Optimisation of our dynamic CPU feature framework, so that all
detected features are enabled via a single stop_machine() invocation
- KPTI whitelisting of Cortex-A CPUs unaffected by Meltdown, so that
they can benefit from global TLB entries when KASLR is not in use
- 52-bit virtual addressing for userspace (kernel remains 48-bit)
- Patch in LSE atomics for per-cpu atomic operations
- Custom preempt.h implementation to avoid unconditional calls to
preempt_schedule() from preempt_enable()
- Support for the new 'SB' Speculation Barrier instruction
- Vectorised implementation of XOR checksumming and CRC32 optimisations
- Workaround for Cortex-A76 erratum #1165522
- Improved compatibility with Clang/LLD
- Support for TX2 system PMUS for profiling the L3 cache and DMC
- Reflect read-only permissions in the linear map by default
- Ensure MMIO reads are ordered with subsequent calls to Xdelay()
- Initial support for memory hotplug
- Tweak the threshold when we invalidate the TLB by-ASID, so that
mremap() performance is improved for ranges spanning multiple PMDs.
- Minor refactoring and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJcE4TmAAoJELescNyEwWM0Nr0H/iaU7/wQSzHyNXtZoImyKTul
Blu2ga4/EqUrTU7AVVfmkl/3NBILWlgQVpY6tH6EfXQuvnxqD7CizbHyLdyO+z0S
B5PsFUH2GLMNAi48AUNqGqkgb2knFbg+T+9IimijDBkKg1G/KhQnRg6bXX32mLJv
Une8oshUPBVJMsHN1AcQknzKariuoE3u0SgJ+eOZ9yA2ZwKxP4yy1SkDt3xQrtI0
lojeRjxcyjTP1oGRNZC+BWUtGOT35p7y6cGTnBd/4TlqBGz5wVAJUcdoxnZ6JYVR
O8+ob9zU+4I0+SKt80s7pTLqQiL9rxkKZ5joWK1pr1g9e0s5N5yoETXKFHgJYP8=
=sYdt
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 festive updates from Will Deacon:
"In the end, we ended up with quite a lot more than I expected:
- Support for ARMv8.3 Pointer Authentication in userspace (CRIU and
kernel-side support to come later)
- Support for per-thread stack canaries, pending an update to GCC
that is currently undergoing review
- Support for kexec_file_load(), which permits secure boot of a kexec
payload but also happens to improve the performance of kexec
dramatically because we can avoid the sucky purgatory code from
userspace. Kdump will come later (requires updates to libfdt).
- Optimisation of our dynamic CPU feature framework, so that all
detected features are enabled via a single stop_machine()
invocation
- KPTI whitelisting of Cortex-A CPUs unaffected by Meltdown, so that
they can benefit from global TLB entries when KASLR is not in use
- 52-bit virtual addressing for userspace (kernel remains 48-bit)
- Patch in LSE atomics for per-cpu atomic operations
- Custom preempt.h implementation to avoid unconditional calls to
preempt_schedule() from preempt_enable()
- Support for the new 'SB' Speculation Barrier instruction
- Vectorised implementation of XOR checksumming and CRC32
optimisations
- Workaround for Cortex-A76 erratum #1165522
- Improved compatibility with Clang/LLD
- Support for TX2 system PMUS for profiling the L3 cache and DMC
- Reflect read-only permissions in the linear map by default
- Ensure MMIO reads are ordered with subsequent calls to Xdelay()
- Initial support for memory hotplug
- Tweak the threshold when we invalidate the TLB by-ASID, so that
mremap() performance is improved for ranges spanning multiple PMDs.
- Minor refactoring and cleanups"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (125 commits)
arm64: kaslr: print PHYS_OFFSET in dump_kernel_offset()
arm64: sysreg: Use _BITUL() when defining register bits
arm64: cpufeature: Rework ptr auth hwcaps using multi_entry_cap_matches
arm64: cpufeature: Reduce number of pointer auth CPU caps from 6 to 4
arm64: docs: document pointer authentication
arm64: ptr auth: Move per-thread keys from thread_info to thread_struct
arm64: enable pointer authentication
arm64: add prctl control for resetting ptrauth keys
arm64: perf: strip PAC when unwinding userspace
arm64: expose user PAC bit positions via ptrace
arm64: add basic pointer authentication support
arm64/cpufeature: detect pointer authentication
arm64: Don't trap host pointer auth use to EL2
arm64/kvm: hide ptrauth from guests
arm64/kvm: consistently handle host HCR_EL2 flags
arm64: add pointer authentication register bits
arm64: add comments about EC exception levels
arm64: perf: Treat EXCLUDE_EL* bit definitions as unsigned
arm64: kpti: Whitelist Cortex-A CPUs that don't implement the CSV3 field
arm64: enable per-task stack canaries
...
Freescale updates from Scott:
"Highlights include elimination of legacy clock bindings use from dts
files, an 83xx watchdog handler, fixes to old dts interrupt errors, and
some minor cleanup."
The structure of the ret_stack array on the task struct is going to
change, and accessing it directly via the curr_ret_stack index will no
longer give the ret_stack entry that holds the return address. To access
that, architectures must now use ftrace_graph_get_ret_stack() to get the
associated ret_stack that matches the saved return address.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The /chosen/linux,stdout-path is "deprecated" in favour of
/chosen/stdout-path so we should be checking for both.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
HMIs will crash the kernel due to
BRANCH_LINK_TO_FAR(hmi_exception_realmode)
Calling into the OPD instead of the actual code.
Fixes: 2337d20728 ("powerpc/64: CONFIG_RELOCATABLE support for hmi interrupts")
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Use DOTSYM() rather than #ifdef]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
A couple of open coded iterating thru the child node names are converted
to use for_each_child_of_node() instead.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In preparation to remove the node name pointer from struct
device_node, convert printf users to use the %pOFn format specifier.
pmem.c was recently added and missed the initial conversion.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This comment talks about PTEs being 64-bits and PMD/PGD being 32-bits,
but that hasn't been true since 2005 when David Gibson implemented
4-level page tables in the commit titled "Four level pagetables for
ppc64".
Remove it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In update_lmb_associativity_index() we lookup dr_node using
of_find_node_by_path() which takes a reference for us. In the
non-error case we forget to drop the reference. Note that
find_aa_index() does modify properties of the node, but doesn't need
an extra reference held once it's returned.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
mpc8641_hpcn was updated to 4-cell interrupt specifiers, but
PCI interrupt-map was not updated. It was also missing #interrupt-cells
on the outer PCI buses.
p1020rdb-pc was updated to 4-cell interrupt specifiers, but
the ethernet-phy nodes weren't updated.
mpc832x_rdb had an invalid "interrupts = <0>" on the ethernet-phy nodes.
Besides being the wrong number of cells, 0 is not a valid IPIC interrupt
according to ipic.c. Presumably it was meant to indicate that these
PHYs are not connected to an interrupt.
Signed-off-by: Scott Wood <oss@buserror.net>
The driver retains compatibility with old device trees, but we don't
want the old nodes lying around to be copied, or used as a reference
(some of the mux options are incorrect), or even just being clutter.
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
[scottwood: removed sysclk node added by Andy]
Signed-off-by: Scott Wood <oss@buserror.net>
When the watchdog timer is set in interrupt mode, it causes a
machine check when it times out. The purpose of this mode is to
ease debugging, not to crash the kernel and reboot the machine.
This patch implements a special handling for that, in order to not
crash the kernel if the watchdog times out while in interrupt or
within the idle task.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[scottwood: added missing #include]
Signed-off-by: Scott Wood <oss@buserror.net>
Fix a spelling mistake in a register description.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Scott Wood <oss@buserror.net>
swiotlb will only bounce buffer when the effective dma address for the
device is smaller than the actual DMA range. Instead of flipping between
the swiotlb and nommu ops for FSL SOCs that have the second outbound
window just don't set the bus dma_mask in this case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Scott Wood <oss@buserror.net>
The Kconfig lexer supports special characters such as '.' and '/' in
the parameter context. In my understanding, the reason is just to
support bare file paths in the source statement.
I do not see a good reason to complicate Kconfig for the room of
ambiguity.
The majority of code already surrounds file paths with double quotes,
and it makes sense since file paths are constant string literals.
Make it treewide consistent now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
This has 5 commits that fix page dirty tracking when running nested
HV KVM guests, from Suraj Jitindar Singh.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJcHGnCAAoJEJ2a6ncsY3GfaMQIAKP1KQ/SzE38gORRjdf4aUTf
8X6+B6bAjVPwu0OgR2xoU4hPT8vpViG8gIjlspDm/v1igRlokz5GeCEXXlttQwK6
5JFfqS+psCQ/Z/bPFo0uW7cOojeDeE3s1Vd3XXjMH79T6Mvpg54fYutvxd+qbjW6
gAl/jGK6xxo1XsaQfySeSSLA3b8ibI77mjnPBgvbSHbrxBAIjoAfqKTVSjrPwR2b
ZvHyCbaoX2uOGyWrw9O73CqCgsiXEOQvr8dLEjsT7a+brrJBO4mv20s6DzlpC1lS
YVHd8GAfk44h1fxsNXsj9eEUIcRMEB4fYYOd/u0TECdeyFFWz+8JjBhm6u0TRck=
=Zrya
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-next-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into kvm-next
Second PPC KVM update for 4.21
This has 5 commits that fix page dirty tracking when running nested
HV KVM guests, from Suraj Jitindar Singh.
The patch is to make kvm_set_spte_hva() return int and caller can
check return value to determine flush tlb or not.
Signed-off-by: Lan Tianyu <Tianyu.Lan@microsoft.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When a page fault happens in a GPU, the GPU signals the OS and the GPU
driver calls the fault handler which populated a page table; this allows
the GPU to complete an ATS request.
On the bare metal get_user_pages() is enough as it adds a pte to
the kernel page table but under KVM the partition scope tree does not get
updated so ATS will still fail.
This reads a byte from an effective address which causes HV storage
interrupt and KVM updates the partition scope tree.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A broken device tree might contain more than 8 values and introduce hard
to debug memory corruption bug. This adds the boundary check.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In order to make ATS work and translate addresses for arbitrary
LPID and PID, we need to program an NPU with LPID and allow PID wildcard
matching with a specific MSR mask.
This implements a helper to assign a GPU to LPAR and program the NPU
with a wildcard for PID and a helper to do clean-up. The helper takes
MSR (only DR/HV/PR/SF bits are allowed) to program them into NPU2 for
ATS checkout requests support.
This exports pnv_npu2_unmap_lpar_dev() as following patches will use it
from the VFIO driver.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At the moment the powernv platform registers an IOMMU group for each
PE. There is an exception though: an NVLink bridge which is attached
to the corresponding GPU's IOMMU group making it a master.
Now we have POWER9 systems with GPUs connected to each other directly
bypassing PCI. At the moment we do not control state of these links so
we have to put such interconnected GPUs to one IOMMU group which means
that the old scheme with one GPU as a master won't work - there will
be up to 3 GPUs in such group.
This introduces a npu_comp struct which represents a compound IOMMU
group made of multiple PEs - PCI PEs (for GPUs) and NPU PEs (for
NVLink bridges). This converts the existing NVLink1 code to use the
new scheme. >From now on, each PE must have a valid
iommu_table_group_ops which will either be called directly (for a
single PE group) or indirectly from a compound group handlers.
This moves IOMMU group registration for NVLink-connected GPUs to
npu-dma.c. For POWER8, this stores a new compound group pointer in the
PE (so a GPU is still a master); for POWER9 the new group pointer is
stored in an NPU (which is allocated per a PCI host controller).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[mpe: Initialise npdev to NULL in pnv_try_setup_npu_table_group()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At the moment NPU IOMMU is manipulated directly from the IODA2 PCI
PE code; PCI PE acts as a master to NPU PE. Soon we will have compound
IOMMU groups with several PEs from several different PHB (such as
interconnected GPUs and NPUs) so there will be no single master but
a one big IOMMU group.
This makes a first step and converts an NPU PE with a set of extern
function to a table group.
This should cause no behavioral change. Note that
pnv_npu_release_ownership() has never been implemented.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Normal PCI PEs have 2 TVEs, one per a DMA window; however NPU PE has only
one which points to one of two tables of the corresponding PCI PE.
So whenever a new DMA window is programmed to PEs, the NPU PE needs to
release old table in order to use the new one.
Commit d41ce7b1bc ("powerpc/powernv/npu: Do not try invalidating 32bit
table when 64bit table is enabled") did just that but in pci-ioda.c
while it actually belongs to npu-dma.c.
This moves the single TVE handling to npu-dma.c. This does not implement
restoring though as it is highly unlikely that we can set the table to
PCI PE and cannot to NPU PE and if that fails, we could only set 32bit
table to NPU PE and this configuration is not really supported or wanted.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The iommu_table pointer stored in iommu_table_group may get stale
by accident, this adds referencing and removes a redundant comment
about this.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Registering new IOMMU groups and adding devices to them are separated in
code and the latter is dug in the DMA setup code which it does not
really belong to.
This moved IOMMU groups setup to a separate helper which registers a group
and adds devices as before. This does not make a difference as IOMMU
groups are not used anyway; the only dependency here is that
iommu_add_device() requires a valid pointer to an iommu_table
(set by set_iommu_table_base()).
To keep the old behaviour, this does not add new IOMMU groups for PEs
with no DMA weight and also skips NVLink bridges which do not have
pci_controller_ops::setup_bridge (the normal way of adding PEs).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The powernv platform registers IOMMU groups and adds devices to them
from the pci_controller_ops::setup_bridge() hook except one case when
virtual functions (SRIOV VFs) are added from a bus notifier.
The pseries platform registers IOMMU groups from
the pci_controller_ops::dma_bus_setup() hook and adds devices from
the pci_controller_ops::dma_dev_setup() hook. The very same bus notifier
used for powernv does not add devices for pseries though as
__of_scan_bus() adds devices first, then it does the bus/dev DMA setup.
Both platforms use iommu_add_device() which takes a device and expects
it to have a valid IOMMU table struct with an iommu_table_group pointer
which in turn points the iommu_group struct (which represents
an IOMMU group). Although the helper seems easy to use, it relies on
some pre-existing device configuration and associated data structures
which it does not really need.
This simplifies iommu_add_device() to take the table_group pointer
directly. Pseries already has a table_group pointer handy and the bus
notified is not used anyway. For powernv, this copies the existing bus
notifier, makes it work for powernv only which means an easy way of
getting to the table_group pointer. This was tested on VFs but should
also support physical PCI hotplug.
Since iommu_add_device() receives the table_group pointer directly,
pseries does not do TCE cache invalidation (the hypervisor does) nor
allow multiple groups per a VFIO container (in other words sharing
an IOMMU table between partitionable endpoints), this removes
iommu_table_group_link from pseries.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pci_dma_bus_setup_pSeries and pci_dma_dev_setup_pSeries hooks are
registered for the pseries platform which does not have FW_FEATURE_LPAR;
these would be pre-powernv platforms which we never supported PCI pass
through for anyway so remove it.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We already changed NPU API for GPUs to not to call OPAL and the remaining
bit is initializing NPU structures.
This searches for POWER9 NVLinks attached to any device on a PHB and
initializes an NPU structure if any found.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We might have memory@ nodes with "linux,usable-memory" set to zero
(for example, to replicate powernv's behaviour for GPU coherent memory)
which means that the memory needs an extra initialization but since
it can be used afterwards, the pseries platform will try mapping it
for DMA so the DMA window needs to cover those memory regions too;
if the window cannot cover new memory regions, the memory onlining fails.
This walks through the memory nodes to find the highest RAM address to
let a huge DMA window cover that too in case this memory gets onlined
later.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When introduced, the NPU context init/destroy helpers called OPAL which
enabled/disabled PID (a userspace memory context ID) filtering in an NPU
per a GPU; this was a requirement for P9 DD1.0. However newer chip
revision added a PID wildcard support so there is no more need to
call OPAL every time a new context is initialized. Also, since the PID
wildcard support was added, skiboot does not clear wildcard entries
in the NPU so these remain in the hardware till the system reboot.
This moves LPID and wildcard programming to the PE setup code which
executes once during the booting process so NPU2 context init/destroy
won't need to do additional configuration.
This replaces the check for FW_FEATURE_OPAL with a check for npu!=NULL as
this is the way to tell if the NPU support is present and configured.
This moves pnv_npu2_init() declaration as pseries should be able to use it.
This keeps pnv_npu2_map_lpar() in powernv as pseries is not allowed to
call that. This exports pnv_npu2_map_lpar_dev() as following patches
will use it from the VFIO driver.
While at it, replace redundant list_for_each_entry_safe() with
a simpler list_for_each_entry().
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The powernv PCI code stores NPU data in the pnv_phb struct. The latter
is referenced by pci_controller::private_data. We are going to have NPU2
support in the pseries platform as well but it does not store any
private_data in in the pci_controller struct; and even if it did,
it would be a different data structure.
This makes npu a pointer and stores it one level higher in
the pci_controller struct.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This new memory does not have page structs as it is not plugged to
the host so gup() will fail anyway.
This adds 2 helpers:
- mm_iommu_newdev() to preregister the "memory device" memory so
the rest of API can still be used;
- mm_iommu_is_devmem() to know if the physical address is one of thise
new regions which we must avoid unpinning of.
This adds @mm to tce_page_is_contained() and iommu_tce_xchg() to test
if the memory is device memory to avoid pfn_to_page().
This adds a check for device memory in mm_iommu_ua_mark_dirty_rm() which
does delayed pages dirtying.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Normally mm_iommu_get() should add a reference and mm_iommu_put() should
remove it. However historically mm_iommu_find() does the referencing and
mm_iommu_get() is doing allocation and referencing.
We are going to add another helper to preregister device memory so
instead of having mm_iommu_new() (which pre-registers the normal memory
and references the region), we need separate helpers for pre-registering
and referencing.
This renames:
- mm_iommu_get to mm_iommu_new;
- mm_iommu_find to mm_iommu_get.
This changes mm_iommu_get() to reference the region so the name now
reflects what it does.
This removes the check for exact match from mm_iommu_new() as we want it
to fail on existing regions; mm_iommu_get() should be used instead.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The skiboot firmware has a hot reset handler which fences the NVIDIA V100
GPU RAM on Witherspoons and makes accesses no-op instead of throwing HMIs:
https://github.com/open-power/skiboot/commit/fca2b2b839a67
Now we are going to pass V100 via VFIO which most certainly involves
KVM guests which are often terminated without getting a chance to offline
GPU RAM so we end up with a running machine with misconfigured memory.
Accessing this memory produces hardware management interrupts (HMI)
which bring the host down.
To suppress HMIs, this wires up this hot reset hook to vfio_pci_disable()
via pci_disable_device() which switches NPU2 to a safe mode and prevents
HMIs.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alistair Popple <alistair@popple.id.au>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On the 8xx, no-execute is set via PPP bits in the PTE. Therefore
a no-exec fault generates DSISR_PROTFAULT error bits,
not DSISR_NOEXEC_OR_G.
This patch adds DSISR_PROTFAULT in the test mask.
Fixes: d3ca587404 ("powerpc/mm: Fix reporting of kernel execute faults")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
System call table generation script must be run to gener-
ate unistd_32/64.h and syscall_table_32/64/c32/spu.h files.
This patch will have changes which will invokes the script.
This patch will generate unistd_32/64.h and syscall_table-
_32/64/c32/spu.h files by the syscall table generation
script invoked by parisc/Makefile and the generated files
against the removed files must be identical.
The generated uapi header file will be included in uapi/-
asm/unistd.h and generated system call table header file
will be included by kernel/systbl.S file.
Signed-off-by: Firoz Khan <firoz.khan@linaro.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The system call tables are in different format in all
architecture and it will be difficult to manually add or
modify the system calls in the respective files. To make
it easy by keeping a script and which will generate the
uapi header and syscall table file. This change will also
help to unify the implementation across all architectures.
The system call table generation script is added in
syscalls directory which contain the script to generate
both uapi header file and system call table files.
The syscall.tbl file will be the input for the scripts.
syscall.tbl contains the list of available system calls
along with system call number and corresponding entry point.
Add a new system call in this architecture will be possible
by adding new entry in the syscall.tbl file.
Adding a new table entry consisting of:
- System call number.
- ABI.
- System call name.
- Entry point name.
- Compat entry name, if required.
syscallhdr.sh and syscalltbl.sh will generate uapi header-
unistd_32/64.h and syscall_table_32/64/c32/spu.h files
respectively. File syscall_table_32/64/c32/spu.h is incl-
uded by syscall.S - the real system call table. Both *.sh
files will parse the content syscall.tbl to generate the
header and table files.
ARM, s390 and x86 architecuture does have similar support.
I leverage their implementation to come up with a generic
solution.
Signed-off-by: Firoz Khan <firoz.khan@linaro.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PowerPC uses a syscall table with native and compat calls
interleaved, which is a slightly simpler way to define two
matching tables.
As we move to having the tables generated, that advantage
is no longer important, but the interleaved table gets in
the way of using the same scripts as on the other archit-
ectures.
Split out a new compat_sys_call_table symbol that contains
all the compat calls, and leave the main table for the nat-
ive calls, to more closely match the method we use every-
where else.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Firoz Khan <firoz.khan@linaro.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the macro definition for compat_sys_sigsuspend from
asm/systbl.h to the file which it is getting included.
One of the patch in this patch series is generating uapi
header and syscall table files. In order to come up with
a common implimentation across all architecture, we need
to do this change.
This change will simplify the implementation of system
call table generation script and help to come up a common
implementation across all architecture.
Signed-off-by: Firoz Khan <firoz.khan@linaro.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
NR_syscalls macro holds the number of system call exist
in powerpc architecture. We have to change the value of
NR_syscalls, if we add or delete a system call.
One of the patch in this patch series has a script which
will generate a uapi header based on syscall.tbl file.
The syscall.tbl file contains the number of system call
information. So we have two option to update NR_syscalls
value.
1. Update NR_syscalls in asm/unistd.h manually by count-
ing the no.of system calls. No need to update NR_sys-
calls until we either add a new system call or delete
existing system call.
2. We can keep this feature in above mentioned script,
that will count the number of syscalls and keep it in
a generated file. In this case we don't need to expli-
citly update NR_syscalls in asm/unistd.h file.
The 2nd option will be the recommended one. For that, I
added the __NR_syscalls macro in uapi/asm/unistd.h along
with NR_syscalls asm/unistd.h. The macro __NR_syscalls
also added for making the name convention same across all
architecture. While __NR_syscalls isn't strictly part of
the uapi, having it as part of the generated header to
simplifies the implementation. We also need to enclose
this macro with #ifdef __KERNEL__ to avoid side effects.
Signed-off-by: Firoz Khan <firoz.khan@linaro.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Protection key tracking information is not copied over to the
mm_struct of the child during fork(). This can cause the child to
erroneously allocate keys that were already allocated. Any allocated
execute-only key is lost aswell.
Add code; called by dup_mmap(), to copy the pkey state from parent to
child explicitly.
This problem was originally found by Dave Hansen on x86, which turns
out to be a problem on powerpc aswell.
Fixes: cf43d3b264 ("powerpc: Enable pkey subsystem")
Cc: stable@vger.kernel.org # v4.16+
Reviewed-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is a TM Bad Thing bug that can be caused when you return from a
signal context in a suspended transaction but with ucontext MSR[TS] unset.
This forces regs->msr[TS] to be set at syscall entrance (since the CPU
state is transactional). It also calls treclaim() to flush the transaction
state, which is done based on the live (mfmsr) MSR state.
Since user context MSR[TS] is not set, then restore_tm_sigcontexts() is not
called, thus, not executing recheckpoint, keeping the CPU state as not
transactional. When calling rfid, SRR1 will have MSR[TS] set, but the CPU
state is non transactional, causing the TM Bad Thing with the following
stack:
[ 33.862316] Bad kernel stack pointer 3fffd9dce3e0 at c00000000000c47c
cpu 0x8: Vector: 700 (Program Check) at [c00000003ff7fd40]
pc: c00000000000c47c: fast_exception_return+0xac/0xb4
lr: 00003fff865f442c
sp: 3fffd9dce3e0
msr: 8000000102a03031
current = 0xc00000041f68b700
paca = 0xc00000000fb84800 softe: 0 irq_happened: 0x01
pid = 1721, comm = tm-signal-sigre
Linux version 4.9.0-3-powerpc64le (debian-kernel@lists.debian.org) (gcc version 6.3.0 20170516 (Debian 6.3.0-18) ) #1 SMP Debian 4.9.30-2+deb9u2 (2017-06-26)
WARNING: exception is not recoverable, can't continue
The same problem happens on 32-bits signal handler, and the fix is very
similar, if tm_recheckpoint() is not executed, then regs->msr[TS] should be
zeroed.
This patch also fixes a sparse warning related to lack of indentation when
CONFIG_PPC_TRANSACTIONAL_MEM is set.
Fixes: 2b0a576d15 ("powerpc: Add new transactional memory state to the signal context")
CC: Stable <stable@vger.kernel.org> # 3.10+
Signed-off-by: Breno Leitao <leitao@debian.org>
Tested-by: Michal Suchánek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Usually a TM Bad Thing exception is raised due to three different problems.
a) touching SPRs in an active transaction; b) using TM instruction with the
facility disabled and c) setting a wrong MSR/SRR1 at RFID.
The two initial cases are easy to identify by looking at the instructions.
The latter case is harder, because the MSR is masked after RFID, so, it is
very useful to look at the previous MSR (SRR1) before RFID as also the
current and masked MSR.
Since MSR is saved at paca just before RFID, this patch prints it if a TM
Bad thing happen, helping to understand what is the invalid TM transition
that is causing the exception.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As other exit points, move SRR1 (MSR) into paca->tm_scratch, so, if
there is a TM Bad Thing in RFID, it is easy to understand what was the
SRR1 value being used.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On a signal handler return, the user could set a context with MSR[TS] bits
set, and these bits would be copied to task regs->msr.
At restore_tm_sigcontexts(), after current task regs->msr[TS] bits are set,
several __get_user() are called and then a recheckpoint is executed.
This is a problem since a page fault (in kernel space) could happen when
calling __get_user(). If it happens, the process MSR[TS] bits were
already set, but recheckpoint was not executed, and SPRs are still invalid.
The page fault can cause the current process to be de-scheduled, with
MSR[TS] active and without tm_recheckpoint() being called. More
importantly, without TEXASR[FS] bit set also.
Since TEXASR might not have the FS bit set, and when the process is
scheduled back, it will try to reclaim, which will be aborted because of
the CPU is not in the suspended state, and, then, recheckpoint. This
recheckpoint will restore thread->texasr into TEXASR SPR, which might be
zero, hitting a BUG_ON().
kernel BUG at /build/linux-sf3Co9/linux-4.9.30/arch/powerpc/kernel/tm.S:434!
cpu 0xb: Vector: 700 (Program Check) at [c00000041f1576d0]
pc: c000000000054550: restore_gprs+0xb0/0x180
lr: 0000000000000000
sp: c00000041f157950
msr: 8000000100021033
current = 0xc00000041f143000
paca = 0xc00000000fb86300 softe: 0 irq_happened: 0x01
pid = 1021, comm = kworker/11:1
kernel BUG at /build/linux-sf3Co9/linux-4.9.30/arch/powerpc/kernel/tm.S:434!
Linux version 4.9.0-3-powerpc64le (debian-kernel@lists.debian.org) (gcc version 6.3.0 20170516 (Debian 6.3.0-18) ) #1 SMP Debian 4.9.30-2+deb9u2 (2017-06-26)
enter ? for help
[c00000041f157b30] c00000000001bc3c tm_recheckpoint.part.11+0x6c/0xa0
[c00000041f157b70] c00000000001d184 __switch_to+0x1e4/0x4c0
[c00000041f157bd0] c00000000082eeb8 __schedule+0x2f8/0x990
[c00000041f157cb0] c00000000082f598 schedule+0x48/0xc0
[c00000041f157ce0] c0000000000f0d28 worker_thread+0x148/0x610
[c00000041f157d80] c0000000000f96b0 kthread+0x120/0x140
[c00000041f157e30] c00000000000c0e0 ret_from_kernel_thread+0x5c/0x7c
This patch simply delays the MSR[TS] set, so, if there is any page fault in
the __get_user() section, it does not have regs->msr[TS] set, since the TM
structures are still invalid, thus avoiding doing TM operations for
in-kernel exceptions and possible process reschedule.
With this patch, the MSR[TS] will only be set just before recheckpointing
and setting TEXASR[FS] = 1, thus avoiding an interrupt with TM registers in
invalid state.
Other than that, if CONFIG_PREEMPT is set, there might be a preemption just
after setting MSR[TS] and before tm_recheckpoint(), thus, this block must
be atomic from a preemption perspective, thus, calling
preempt_disable/enable() on this code.
It is not possible to move tm_recheckpoint to happen earlier, because it is
required to get the checkpointed registers from userspace, with
__get_user(), thus, the only way to avoid this undesired behavior is
delaying the MSR[TS] set.
The 32-bits signal handler seems to be safe this current issue, but, it
might be exposed to the preemption issue, thus, disabling preemption in
this chunk of code.
Changes from v2:
* Run the critical section with preempt_disable.
Fixes: 87b4e5393a ("powerpc/tm: Fix return of active 64bit signals")
Cc: stable@vger.kernel.org (v3.9+)
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The rc bits contained in ptes are used to track whether a page has been
accessed and whether it is dirty. The accessed bit is used to age a page
and the dirty bit to track whether a page is dirty or not.
Now that we support nested guests there are three ptes which track the
state of the same page:
- The partition-scoped page table in the L1 guest, mapping L2->L1 address
- The partition-scoped page table in the host for the L1 guest, mapping
L1->L0 address
- The shadow partition-scoped page table for the nested guest in the host,
mapping L2->L0 address
The idea is to attempt to keep the rc state of these three ptes in sync,
both when setting and when clearing rc bits.
When setting the bits we achieve consistency by:
- Initially setting the bits in the shadow page table as the 'and' of the
other two.
- When updating in software the rc bits in the shadow page table we
ensure the state is consistent with the other two locations first, and
update these before reflecting the change into the shadow page table.
i.e. only set the bits in the L2->L0 pte if also set in both the
L2->L1 and the L1->L0 pte.
When clearing the bits we achieve consistency by:
- The rc bits in the shadow page table are only cleared when discarding
a pte, and we don't need to record this as if either bit is set then
it must also be set in the pte mapping L1->L0.
- When L1 clears an rc bit in the L2->L1 mapping it __should__ issue a
tlbie instruction
- This means we will discard the pte from the shadow page table
meaning the mapping will have to be setup again.
- When setup the pte again in the shadow page table we will ensure
consistency with the L2->L1 pte.
- When the host clears an rc bit in the L1->L0 mapping we need to also
clear the bit in any ptes in the shadow page table which map the same
gfn so we will be notified if a nested guest accesses the page.
This case is what this patch specifically concerns.
- We can search the nest_rmap list for that given gfn and clear the
same bit from all corresponding ptes in shadow page tables.
- If a nested guest causes either of the rc bits to be set by software
in future then we will update the L1->L0 pte and maintain consistency.
With the process outlined above we aim to maintain consistency of the 3
pte locations where we track rc for a given guest page.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Introduce a function kvmhv_update_nest_rmap_rc_list() which for a given
nest_rmap list will traverse it, find the corresponding pte in the shadow
page tables, and if it still maps the same host page update the rc bits
accordingly.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The shadow page table contains ptes for translations from nested guest
address to host address. Currently when creating these ptes we take the
rc bits from the pte for the L1 guest address to host address
translation. This is incorrect as we must also factor in the rc bits
from the pte for the nested guest address to L1 guest address
translation (as contained in the L1 guest partition table for the nested
guest).
By not calculating these bits correctly L1 may not have been correctly
notified when it needed to update its rc bits in the partition table it
maintains for its nested guest.
Modify the code so that the rc bits in the resultant pte for the L2->L0
translation are the 'and' of the rc bits in the L2->L1 pte and the L1->L0
pte, also accounting for whether this was a write access when setting
the dirty bit.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Nested rmap entries are used to store the translation from L1 gpa to L2
gpa when entries are inserted into the shadow (nested) page tables. This
rmap list is located by indexing the rmap array in the memslot by L1
gfn. When we come to search for these entries we only know the L1 page size
(which could be PAGE_SIZE, 2M or a 1G page) and so can only select a gfn
aligned to that size. This means that when we insert the entry, so we can
find it later, we need to align the gfn we use to select the rmap list
in which to insert the entry to L1 page size as well.
By not doing this we were missing nested rmap entries when modifying L1
ptes which were for a page also passed through to an L2 guest.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
We already hold the kvm->mmu_lock spin lock across updating the rc bits
in the pte for the L1 guest. Continue to hold the lock across updating
the rc bits in the pte for the nested guest as well to prevent
invalidations from occurring.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
For fadump to work successfully there should not be any holes in reserved
memory ranges where kernel has asked firmware to move the content of old
kernel memory in event of crash. Now that fadump uses CMA for reserved
area, this memory area is now not protected from hot-remove operations
unless it is cma allocated. Hence, fadump service can fail to re-register
after the hot-remove operation, if hot-removed memory belongs to fadump
reserved region. To avoid this make sure that memory from fadump reserved
area is not hot-removable if fadump is registered.
However, if user still wants to remove that memory, he can do so by
manually stopping fadump service before hot-remove operation.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
fadump fails to register when there are holes in reserved memory area.
This can happen if user has hot-removed a memory that falls in the
fadump reserved memory area. Throw a meaningful error message to the
user in such case.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
[mpe: is_reserved_memory_area_contiguous() returns bool, unsplit string]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
One of the primary issues with Firmware Assisted Dump (fadump) on Power
is that it needs a large amount of memory to be reserved. On large
systems with TeraBytes of memory, this reservation can be quite
significant.
In some cases, fadump fails if the memory reserved is insufficient, or
if the reserved memory was DLPAR hot-removed.
In the normal case, post reboot, the preserved memory is filtered to
extract only relevant areas of interest using the makedumpfile tool.
While the tool provides flexibility to determine what needs to be part
of the dump and what memory to filter out, all supported distributions
default this to "Capture only kernel data and nothing else".
We take advantage of this default and the Linux kernel's Contiguous
Memory Allocator (CMA) to fundamentally change the memory reservation
model for fadump.
Instead of setting aside a significant chunk of memory nobody can use,
this patch uses CMA instead, to reserve a significant chunk of memory
that the kernel is prevented from using (due to MIGRATE_CMA), but
applications are free to use it. With this fadump will still be able
to capture all of the kernel memory and most of the user space memory
except the user pages that were present in CMA region.
Essentially, on a P9 LPAR with 2 cores, 8GB RAM and current upstream:
[root@zzxx-yy10 ~]# free -m
total used free shared buff/cache available
Mem: 7557 193 6822 12 541 6725
Swap: 4095 0 4095
With this patch:
[root@zzxx-yy10 ~]# free -m
total used free shared buff/cache available
Mem: 8133 194 7464 12 475 7338
Swap: 4095 0 4095
Changes made here are completely transparent to how fadump has
traditionally worked.
Thanks to Aneesh Kumar and Anshuman Khandual for helping us understand
CMA and its usage.
TODO:
- Handle case where CMA reservation spans nodes.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
opal_power_control_init() depends on opal message notifier to be
initialized, which is done in opal_init()->opal_message_init(). But both
these initialization are called through machine initcalls and it all
depends on in which order they being called. So far these are called in
correct order (may be we got lucky) and never saw any issue. But it is
clearer to control initialization order explicitly by moving
opal_power_control_init() into opal_init().
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The script "checkpatch.pl" pointed information out like the following.
WARNING: void function return statements are not generally useful
Thus remove such a statement in the affected functions.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Omit an extra message for a memory allocation failure in these
functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A single character (line break) should be put into a sequence.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some data were printed into a sequence by four separate function calls.
Print the same data by two single function calls instead.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CONFIG_EARLY_DEBUG_CPM requires IMMR area TLB to be pinned
otherwise it doesn't survive MMU_init, and the boot fails.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CONFIG_PCI_MSI was made mandatory by commit a311e738b6
("powerpc/powernv: Make PCI non-optional") so the #ifdef
checks around CONFIG_PCI_MSI here can be removed entirely.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix a spelling mistake in a register description.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 14c63f17b1 ("perf: Drop sample rate when sampling is too
slow") introduced a way to throttle PMU interrupts if we're spending
too much time just processing those. Wire up powerpc PMI handler to
use this infrastructure.
We have throttling of the *rate* of interrupts, but this adds
throttling based on the *time taken* to process the interrupts.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
The main new feature this time is support in HV nested KVM for passing
a device that is emulated by a level 0 hypervisor and presented to
level 1 as a PCI device through to a level 2 guest using VFIO.
Apart from that there are improvements for migration of radix guests
under HV KVM and some other fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJcGFzEAAoJEJ2a6ncsY3GfKjoH/Azcf8QIO5ftyHrjazFZOSUh
5Lr24HZTYHheowp6obzuZWRAIyckHmflRmOkv8RVGuA8+Sp+m5pBxN3WTVPOwDUh
WanOWVGJsuhl6qATmkm7xIxmYhQEyLxVNbnWva7WXuZ92rgGCNfHtByHWAx/7vTe
q5Shr4fLIQ8HRzor8Xqqph1I0hQNTE9VsaK1hW/PxI0gsO8qjDwOR8SDpT/aaJrS
Sir+lM0TwCbJREuObDxYAXn1OWy8rMYjlb9fEBv5tmPCQKiB9vJz4tV+ahR9eJ14
PEF57MoBOGwzQXo4geFLuo/Bu8fDygKsKQX1eYGcn6tRGA4pnTxzYl0+dHLBkOM=
=3WkD
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-next-4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
PPC KVM update for 4.21 from Paul Mackerras
The main new feature this time is support in HV nested KVM for passing
a device that is emulated by a level 0 hypervisor and presented to
level 1 as a PCI device through to a level 2 guest using VFIO.
Apart from that there are improvements for migration of radix guests
under HV KVM and some other fixes and cleanups.
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.
Semantic patch information:
Rationale: DEFINE_SIMPLE_ATTRIBUTE + debugfs_create_file()
imposes some significant overhead as compared to
DEFINE_DEBUGFS_ATTRIBUTE + debugfs_create_file_unsafe().
Generated by: scripts/coccinelle/api/debugfs/debugfs_simple_attr.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current implementation of the OPAL_PCI_EEH_FREEZE_STATUS call in
skiboot's NPU driver does not touch the pci_error_type parameter so
it might have garbage but the powernv code analyzes it nevertheless.
This initializes pcierr and fstate to zero in all call sites.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
fixup_phb() is never used, this removes it.
pick_m64_pe() and reserve_m64_pe() are always defined for all powernv
PHBs: they are initialized by pnv_ioda_parse_m64_window() which is
called unconditionally from pnv_pci_init_ioda_phb() which initializes
all known PHB types on powernv so we can open code them.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Report branch predictor state flush as a mitigation for
Spectre variant 2.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At the moment PNV_IODA_PE_DEV is only used for NPU PEs which are not
present on IODA1 machines (i.e. POWER7) so let's remove a piece of
dead code.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the user choses not to use the mitigations, replace
the code sequence with nops.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Switching from the guest to host is another place
where the speculative accesses can be exploited.
Flush the branch predictor when entering KVM.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The macro and few headers are not used so remove them.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In order to protect against speculation attacks on
indirect branches, the branch predictor is flushed at
kernel entry to protect for the following situations:
- userspace process attacking another userspace process
- userspace process attacking the kernel
Basically when the privillege level change (i.e.the kernel
is entered), the branch predictor state is flushed.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The powernv platform maintains 2 TCE tables for VFIO - a hardware TCE
table and a table with userspace addresses; the latter is used for
marking pages dirty when corresponging TCEs are unmapped from
the hardware table.
a68bd1267b ("powerpc/powernv/ioda: Allocate indirect TCE levels
on demand") enabled on-demand allocation of the hardware table,
however it missed the other table so it has still been fully allocated
at the boot time. This fixes the issue by allocating a single level,
just like we do for the hardware table.
Fixes: a68bd1267b ("powerpc/powernv/ioda: Allocate indirect TCE levels on demand")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In order to protect against speculation attacks on
indirect branches, the branch predictor is flushed at
kernel entry to protect for the following situations:
- userspace process attacking another userspace process
- userspace process attacking the kernel
Basically when the privillege level change (i.e. the
kernel is entered), the branch predictor state is flushed.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When the command line argument is present, the Spectre variant 2
mitigations are disabled.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In order to flush the branch predictor the guest kernel performs
writes to the BUCSR register which is hypervisor privilleged. However,
the branch predictor is flushed at each KVM entry, so the branch
predictor has been already flushed, so just return as soon as possible
to guest.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
[mpe: Tweak comment formatting]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently for CONFIG_PPC_FSL_BOOK3E the spectre_v2 file is incorrect:
$ cat /sys/devices/system/cpu/vulnerabilities/spectre_v2
"Mitigation: Software count cache flush"
Which is wrong. Fix it to report vulnerable for now.
Fixes: ee13cb249f ("powerpc/64s: Add support for software count cache flush")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The BUCSR register can be used to invalidate the entries in the
branch prediction mechanisms.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In order to protect against speculation attacks (Spectre
variant 2) on NXP PowerPC platforms, the branch predictor
should be flushed when the privillege level is changed.
This patch is adding the infrastructure to fixup at runtime
the code sections that are performing the branch predictor flush
depending on a boot arg parameter which is added later in a
separate patch.
Signed-off-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the device tree doesn't reside in the memory which is declared
inside it, it has to be moved as well as this memory will not be
mapped by the kernel.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reverts the remains of commit b9ef7d6b11 ("powerpc: Update
default configurations").
That commit was proceeded by a commit which added a config option to
control use of BOOTX for early debug, ie. PPC_EARLY_DEBUG_BOOTX, and
then the update of the defconfigs was intended to not change behaviour
by then enabling the new config option.
However enabling PPC_EARLY_DEBUG had other consequences, notably
causing us to register the udbg console at the end of udbg_early_init().
This means on a system which doesn't have anything that BOOTX can
use (most systems), we register the udbg console very early but the
bootx code just throws everything away, meaning early boot messages
are never printed to the console.
What we want to happen is for the udbg console to only be registered
later (from setup_arch()) once we've setup udbg_putc, and then all
early boot messages will be replayed.
Fixes: b9ef7d6b11 ("powerpc: Update default configurations")
Reported-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For this use case, completions and semaphores are equivalent,
but semaphores are an awkward interface that should generally
be avoided, so use the completion instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The bamboo dts has a bug: it uses a non-naturally aligned range
for PCI memory space. This isnt' supported by the code, thus
causing PCI to break on this system.
This is due to the fact that while the chip memory map has 1G
reserved for PCI memory, it's only 512M aligned. The code doesn't
know how to split that into 2 different PMMs and fails, so limit
the region to 512M.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a IRQ init routine for the Nemo board which inits and attatches
the i8259 found in the SB600, and a cascade routine to dispatch the
interrupts.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add routines for Nemo specific devices to init at boot time, these
being board level power-off and SB600's rtc.
Also add a run time variable to prevent these being activated
if we boot on a reference board.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a IRQ init routine for the Nemo board which inits and attatches
the i8259 found in the SB600, and a cascade routine to dispatch the
interrupts.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The A-Eon Amigaone X1000's Nemo motherboard has an AMD SB600
connected to one of the PCI-e root ports on its PaSemi
Pwrficient 1628M SoC. Normally the SB600 southbridge would be
connected to a hidden PCI-e port on the system's northbridge,
and as a result doesn't fully comply with the PCI-e spec.
Add code to relax the PCI-e detection in both the root port
and the Linux kernel allowing on board devices to be detected.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As several other arches including x86, this patch makes it explicit
that a bad page fault is a NULL pointer dereference when the fault
address is lower than PAGE_SIZE
In the mean time, this page makes all bad_page_fault() messages
shorter so that they remain on one single line. And it prefixes them
by "BUG: " so that they get easily grepped.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Avoid pr_cont()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Combine the SYSCALL_EMU and SYSCALL_TRACE handling so that we only
call tracehook_report_syscall_entry() in one place.
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
[mpe: Flesh out change log, s/cached_flags/flags/, reflow comments]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Powerpc has somewhat odd usage where ZONE_DMA is used for all memory on
common 64-bit configfs, and ZONE_DMA32 is used for 31-bit schemes.
Move to a scheme closer to what other architectures use (and I dare to
say the intent of the system):
- ZONE_DMA: optionally for memory < 31-bit (64-bit embedded only)
- ZONE_NORMAL: everything addressable by the kernel
- ZONE_HIGHMEM: memory > 32-bit for 32-bit kernels
Also provide information on how ZONE_DMA is used by defining
ARCH_ZONE_DMA_BITS.
Contains various fixes from Benjamin Herrenschmidt.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The implemementation for the CONFIG_NOT_COHERENT_CACHE case doesn't share
any code with the one for systems with coherent caches. Split it off
and merge it with the helpers in dma-noncoherent.c that have no other
callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The unmap methods need to transfer memory ownership back from the
device to the cpu by identical means as dma_sync_*_to_cpu. I'm not
sure powerpc needs to do any work in this transfer direction, but
given that it does invalidate the caches in dma_sync_*_to_cpu already
we should make sure we also do so on unmapping.
Signed-off-by: Christoph Hellwig <hch@lst.de>
[mpe: s/dir/direction in dma_nommu_unmap_page()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
AMIGAONE selects NOT_COHERENT_CACHE, so we better allow it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch fixes early DEBUG messages in prom.c:
- Use %px instead of %p to see the addresses
- Cast memblock_phys_mem_size() with (unsigned long long) to
avoid build failure when phys_addr_t is not 64 bits.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When building for ppc32 with clang these flags are unsupported:
-ffixed-r2 and -mmultiple
llvm's lib/Target/PowerPC/PPCRegisterInfo.cpp marks r2 as reserved on
when building for SVR4ABI and !ppc64:
// The SVR4 ABI reserves r2 and r13
if (Subtarget.isSVR4ABI()) {
// We only reserve r2 if we need to use the TOC pointer. If we have no
// explicit uses of the TOC pointer (meaning we're a leaf function with
// no constant-pool loads, etc.) and we have no potential uses inside an
// inline asm block, then we can treat r2 has an ordinary callee-saved
// register.
const PPCFunctionInfo *FuncInfo = MF.getInfo<PPCFunctionInfo>();
if (!TM.isPPC64() || FuncInfo->usesTOCBasePtr() || MF.hasInlineAsm())
markSuperRegs(Reserved, PPC::R2); // System-reserved register
markSuperRegs(Reserved, PPC::R13); // Small Data Area pointer register
}
This means we can safely omit -ffixed-r2 when building for 32-bit
targets.
The -mmultiple/-mno-multiple flags are not supported by clang, so
platforms that might support multiple miss out on using multiple word
instructions.
We wrap these flags in cc-option so that when Clang gains support the
kernel will be able use these flags.
Clang 8 can then build a ppc44x_defconfig which boots in Qemu:
make CC=clang-8 ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu- ppc44x_defconfig
./scripts/config -e CONFIG_DEVTMPFS -d DEVTMPFS_MOUNT
make CC=clang-8 ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu-
qemu-system-ppc -M bamboo \
-kernel arch/powerpc/boot/zImage \
-dtb arch/powerpc/boot/dts/bamboo.dtb \
-initrd ~/ppc32-440-rootfs.cpio \
-nographic -serial stdio -monitor pty -append "console=ttyS0"
Link: https://github.com/ClangBuiltLinux/linux/issues/261
Link: https://bugs.llvm.org/show_bug.cgi?id=39556
Link: https://bugs.llvm.org/show_bug.cgi?id=39555
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove PM_L2_ST_MISS and PM_L2_ST from HW cache event array since
these are bus events. And these needs to be programmed in groups.
Hence remove them.
Fixes: f1fb60bfde ('powerpc/perf: Export Power9 generic and cache events to sysfs')
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In previous generation processors, both bus events and direct
events of performance monitoring unit can be individually
programmabled and monitored in PMCs.
But in Power9, L2/L3 bus events are always available as a
"bank" of 4 events. To obtain the counts for any of the
l2/l3 bus events in a given bank, the user will have to
program PMC4 with corresponding l2/l3 bus event for that
bank.
Patch enforce two contraints incase of L2/L3 bus events.
1)Any L2/L3 event when programmed is also expected to program corresponding
PMC4 event from that group.
2)PMC4 event should always been programmed first due to group constraint
logic limitation
For ex. consider these L3 bus events
PM_L3_PF_ON_CHIP_MEM (0x460A0),
PM_L3_PF_MISS_L3 (0x160A0),
PM_L3_CO_MEM (0x260A0),
PM_L3_PF_ON_CHIP_CACHE (0x360A0),
1) This is an INVALID group for L3 Bus event monitoring,
since it is missing PMC4 event.
perf stat -e "{r160A0,r260A0,r360A0}" < >
And this is a VALID group for L3 Bus events:
perf stat -e "{r460A0,r160A0,r260A0,r360A0}" < >
2) This is an INVALID group for L3 Bus event monitoring,
since it is missing PMC4 event.
perf stat -e "{r260A0,r360A0}" < >
And this is a VALID group for L3 Bus events:
perf stat -e "{r460A0,r260A0,r360A0}" < >
3) This is an INVALID group for L3 Bus event monitoring,
since it is missing PMC4 event.
perf stat -e "{r360A0}" < >
And this is a VALID group for L3 Bus events:
perf stat -e "{r460A0,r360A0}" < >
Patch here implements group constraint logic suggested by Michael Ellerman.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Raw event code has couple of fields "unit" and "cache" in it, to capture
the "unit" to monitor for a given pmcxsel and cache reload qualifier to
program in MMCR1.
isa207_get_constraint() refers "unit" field to update the MMCRC (L2/L3)
Event bus control fields with "cache" bits of the raw event code.
These are power8 specific and not supported by PowerISA v3.0 pmu. So wrap
the checks to be power8 specific. Also, "cache" bit field is referred to
update MMCR1[16:17] and this check can be power8 specific.
Fixes: 7ffd948fae ('powerpc/perf: factor out power8 pmu functions')
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Update the raw event code comment in power9-pmu.c with respect to
"cache" bits, since power9 MMCRC does not support these.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On each sample, Sample Instruction Event Register (SIER) content
is saved in pt_regs. SIER does not have a entry as-is in the pt_regs
but instead, SIER content is saved in the "dar" register of pt_regs.
Patch adds another entry to the perf_regs structure to include the "SIER"
printing which internally maps to the "dar" of pt_regs.
It also check for the SIER availability in the platform and present
value accordingly
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
MMCRA[34:36] and MMCRA[38:44] expose the thresholding counter value.
Thresholding counter can be used to count latency cycles such as
load miss to reload. But threshold counter value is not relevant
when the sampled instruction type is unknown or reserved. Patch to
fix the thresholding counter value to zero when sampled instruction
type is unknown or reserved.
Fixes: 170a315f41c6('powerpc/perf: Support to export MMCRA[TEC*] field to userspace')
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 2865d08dd9 ("powerpc/mm: Move the DSISR_PROTFAULT sanity
check") we moved the protection fault access check before the vma
lookup. That means we hit that WARN_ON when user space accesses a
kernel address. Before that commit this was handled by find_vma() not
finding vma for the kernel address and considering that access as bad
area access.
Avoid the confusing WARN_ON and convert that to a ratelimited printk.
With the patch we now get:
for load:
a.out[5997]: User access of kernel address (c00000000000dea0) - exploit attempt? (uid: 1000)
a.out[5997]: segfault (11) at c00000000000dea0 nip 1317c0798 lr 7fff80d6441c code 1 in a.out[1317c0000+10000]
a.out[5997]: code: 60000000 60420000 3c4c0002 38427790 4bffff20 3c4c0002 38427784 fbe1fff8
a.out[5997]: code: f821ffc1 7c3f0b78 60000000 e9228030 <89290000> 993f002f 60000000 383f0040
for exec:
a.out[6067]: User access of kernel address (c00000000000dea0) - exploit attempt? (uid: 1000)
a.out[6067]: segfault (11) at c00000000000dea0 nip c00000000000dea0 lr 129d507b0 code 1
a.out[6067]: Bad NIP, not dumping instructions.
Fixes: 2865d08dd9 ("powerpc/mm: Move the DSISR_PROTFAULT sanity check")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Tested-by: Breno Leitao <leitao@debian.org>
[mpe: Don't split printk() string across lines]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The 603 doesn't have a HASH table, TLB misses are handled by
software. It is then possible to generate page fault when
_PAGE_EXEC is not set like in nohash/32.
There is one "reserved" PTE bit available, this patch uses
it for _PAGE_EXEC.
In order to support it, set_pte_filter() and
set_access_flags_filter() are made common, and the handling
is made dependent on MMU_FTR_HPTE_TABLE
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Define slice_init_new_context_exec() at all time to avoid
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With the following piece of code, the following compilation warning
is encountered:
if (_IOC_DIR(ioc) != _IOC_NONE) {
int verify = _IOC_DIR(ioc) & _IOC_READ ? VERIFY_WRITE : VERIFY_READ;
if (!access_ok(verify, ioarg, _IOC_SIZE(ioc))) {
drivers/platform/test/dev.c: In function 'my_ioctl':
drivers/platform/test/dev.c:219:7: warning: unused variable 'verify' [-Wunused-variable]
int verify = _IOC_DIR(ioc) & _IOC_READ ? VERIFY_WRITE : VERIFY_READ;
This patch fixes it by referencing 'type' in the macro allthough
doing nothing with it.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
commit f21f49ea63 ("[POWERPC] Remove the dregs of APUS support from
arch/powerpc") removed CONFIG_APUS, but forgot to remove the logic
which adapts tophys() and tovirt() for it.
This patch removes the last stale pieces.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch fixes the loop in p_block_mapped() and v_block_mapped()
to scan the entire bat_addrs[] array.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Depending on the CONFIG selected, many of the MMU features are
not possible. Lets only get the possible ones in MMU_FTRS_POSSIBLE.
This allows gcc to get rid at compile time of code related to
not possible features.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use patch sites and associated helpers to manage TLB handlers
patching instead of hardcoding.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of hardcoding the TLB handlers patching, use
the newly created modify_instruction_site() helper.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use patch_sites and the new modify_instruction_site() function
instead of hardcoding hash functions patching.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of manually patching a blr at hash_page() entry in
MMU_init_hw(), this patch adds a features section in head_32.S
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use patch_site_addr() instead of hardcoding the
address calculation in machine_init()
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add two helpers to avoid hardcoding of instructions modifications.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Using patch_site_addr() helper, patch_instruction_site() and
patch_branch_site() can be simplified and inlined.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In file included from ./include/linux/hugetlb.h:445:0,
from arch/powerpc/kernel/setup-common.c:37:
./arch/powerpc/include/asm/hugetlb.h: In function ‘huge_ptep_clear_flush’:
./arch/powerpc/include/asm/hugetlb.h:154:8: error: variable ‘pte’ set but not used [-Werror=unused-but-set-variable]
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The code:
ifdef CONFIG_6xx
KBUILD_CFLAGS += -mcpu=powerpc
endif
was added in 2006 in commit f48b8296b3 ("[PATCH] powerpc32: Set cpu
explicitly in kernel compiles"). This change was acceptable since the
TARGET_CPU logic was 64-bit only.
Since commit 0e00a8c9fd ("powerpc: Allow CPU selection
also on PPC32") this logic is no longer acceptable after the TARGET_CPU
specific. It currently appends -mcpu=powerpc at the end of the command
line, after any TARGET_CPU specific:
gcc -Wp,-MD,init/.do_mounts.o.d ...
-mcpu=powerpc -mbig-endian -m32 ...
-mcpu=e300c2 ...
-mcpu=powerpc ...
../init/do_mounts.c
Fixes: 0e00a8c9fd ("powerpc: Allow CPU selection also on PPC32")
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
ipic_set_priority() has been unused since 2006 when the last usage was
removed in commit b9f0f1bb2b ("[POWERPC] Adapt ipic driver to new
host_ops interface, add set_irq_type to set IRQ sense").
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Merge our fixes branch again, this has a couple of build fixes and also
a change to do_syscall_trace_enter() that will conflict with a patch we
want to apply in next.
Use the new function to replace the open-coded iommu check.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell Currey <ruscur@russell.cc>
Cc: Sam Bobroff <sbobroff@linux.ibm.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Previously when a device was being emulated by an L1 guest for an L2
guest, that device couldn't then be passed through to an L3 guest. This
was because the L1 guest had no method for accessing L3 memory.
The hcall H_COPY_TOFROM_GUEST provides this access. Thus this setup for
passthrough can now be allowed.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
A guest cannot access quadrants 1 or 2 as this would result in an
exception. Thus introduce the hcall H_COPY_TOFROM_GUEST to be used by a
guest when it wants to perform an access to quadrants 1 or 2, for
example when it wants to access memory for one of its nested guests.
Also provide an implementation for the kvm-hv module.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Allow for a device which is being emulated at L0 (the host) for an L1
guest to be passed through to a nested (L2) guest.
The existing kvmppc_hv_emulate_mmio function can be used here. The main
challenge is that for a load the result must be stored into the L2 gpr,
not an L1 gpr as would normally be the case after going out to qemu to
complete the operation. This presents a challenge as at this point the
L2 gpr state has been written back into L1 memory.
To work around this we store the address in L1 memory of the L2 gpr
where the result of the load is to be stored and use the new io_gpr
value KVM_MMIO_REG_NESTED_GPR to indicate that this is a nested load for
which completion must be done when returning back into the kernel. Then
in kvmppc_complete_mmio_load() the resultant value is written into L1
memory at the location of the indicated L2 gpr.
Note that we don't currently let an L1 guest emulate a device for an L2
guest which is then passed through to an L3 guest.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The functions kvmppc_st and kvmppc_ld are used to access guest memory
from the host using a guest effective address. They do so by translating
through the process table to obtain a guest real address and then using
kvm_read_guest or kvm_write_guest to make the access with the guest real
address.
This method of access however only works for L1 guests and will give the
incorrect results for a nested guest.
We can however use the store_to_eaddr and load_from_eaddr kvmppc_ops to
perform the access for a nested guesti (and a L1 guest). So attempt this
method first and fall back to the old method if this fails and we aren't
running a nested guest.
At this stage there is no fall back method to perform the access for a
nested guest and this is left as a future improvement. For now we will
return to the nested guest and rely on the fact that a translation
should be faulted in before retrying the access.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The kvmppc_ops struct is used to store function pointers to kvm
implementation specific functions.
Introduce two new functions load_from_eaddr and store_to_eaddr to be
used to load from and store to a guest effective address respectively.
Also implement these for the kvm-hv module. If we are using the radix
mmu then we can call the functions to access quadrant 1 and 2.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The POWER9 radix mmu has the concept of quadrants. The quadrant number
is the two high bits of the effective address and determines the fully
qualified address to be used for the translation. The fully qualified
address consists of the effective lpid, the effective pid and the
effective address. This gives then 4 possible quadrants 0, 1, 2, and 3.
When accessing these quadrants the fully qualified address is obtained
as follows:
Quadrant | Hypervisor | Guest
--------------------------------------------------------------------------
| EA[0:1] = 0b00 | EA[0:1] = 0b00
0 | effLPID = 0 | effLPID = LPIDR
| effPID = PIDR | effPID = PIDR
--------------------------------------------------------------------------
| EA[0:1] = 0b01 |
1 | effLPID = LPIDR | Invalid Access
| effPID = PIDR |
--------------------------------------------------------------------------
| EA[0:1] = 0b10 |
2 | effLPID = LPIDR | Invalid Access
| effPID = 0 |
--------------------------------------------------------------------------
| EA[0:1] = 0b11 | EA[0:1] = 0b11
3 | effLPID = 0 | effLPID = LPIDR
| effPID = 0 | effPID = 0
--------------------------------------------------------------------------
In the Guest;
Quadrant 3 is normally used to address the operating system since this
uses effPID=0 and effLPID=LPIDR, meaning the PID register doesn't need to
be switched.
Quadrant 0 is normally used to address user space since the effLPID and
effPID are taken from the corresponding registers.
In the Host;
Quadrant 0 and 3 are used as above, however the effLPID is always 0 to
address the host.
Quadrants 1 and 2 can be used by the host to address guest memory using
a guest effective address. Since the effLPID comes from the LPID register,
the host loads the LPID of the guest it would like to access (and the
PID of the process) and can perform accesses to a guest effective
address.
This means quadrant 1 can be used to address the guest user space and
quadrant 2 can be used to address the guest operating system from the
hypervisor, using a guest effective address.
Access to the quadrants can cause a Hypervisor Data Storage Interrupt
(HDSI) due to being unable to perform partition scoped translation.
Previously this could only be generated from a guest and so the code
path expects us to take the KVM trampoline in the interrupt handler.
This is no longer the case so we modify the handler to call
bad_page_fault() to check if we were expecting this fault so we can
handle it gracefully and just return with an error code. In the hash mmu
case we still raise an unknown exception since quadrants aren't defined
for the hash mmu.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
There exists a function kvm_is_radix() which is used to determine if a
kvm instance is using the radix mmu. However this only applies to the
first level (L1) guest. Add a function kvmhv_vcpu_is_radix() which can
be used to determine if the current execution context of the vcpu is
radix, accounting for if the vcpu is running a nested guest.
Currently all nested guests must be radix but this may change in the
future.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The kvm capability KVM_CAP_SPAPR_TCE_VFIO is used to indicate the
availability of in kernel tce acceleration for vfio. However it is
currently the case that this is only available on a powernv machine,
not for a pseries machine.
Thus make this capability dependent on having the cpu feature
CPU_FTR_HVMODE.
[paulus@ozlabs.org - fixed compilation for Book E.]
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds code to flush the partition-scoped page tables for a radix
guest when dirty tracking is turned on or off for a memslot. Only the
guest real addresses covered by the memslot are flushed. The reason
for this is to get rid of any 2M PTEs in the partition-scoped page
tables that correspond to host transparent huge pages, so that page
dirtiness is tracked at a system page (4k or 64k) granularity rather
than a 2M granularity. The page tables are also flushed when turning
dirty tracking off so that the memslot's address space can be
repopulated with THPs if possible.
To do this, we add a new function kvmppc_radix_flush_memslot(). Since
this does what's needed for kvmppc_core_flush_memslot_hv() on a radix
guest, we now make kvmppc_core_flush_memslot_hv() call the new
kvmppc_radix_flush_memslot() rather than calling kvm_unmap_radix()
for each page in the memslot. This has the effect of fixing a bug in
that kvmppc_core_flush_memslot_hv() was previously calling
kvm_unmap_radix() without holding the kvm->mmu_lock spinlock, which
is required to be held.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
