When returning from idle, we rely on the fact that thread_info lives at
the end of the kernel stack, and restore this by masking the saved stack
pointer. Subsequent patches will sever the relationship between the
stack and thread_info, and to cater for this we must save/restore sp_el0
explicitly, storing it in cpu_suspend_ctx.
As cpu_suspend_ctx must be doubleword aligned, this leaves us with an
extra slot in cpu_suspend_ctx. We can use this to save/restore tpidr_el1
in the same way, which simplifies the code, avoiding pointer chasing on
the restore path (as we no longer need to load thread_info::cpu followed
by the relevant slot in __per_cpu_offset based on this).
This patch stashes both registers in cpu_suspend_ctx.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The suspend/resume path in kernel/sleep.S, as used by cpu-idle, does not
save/restore PSTATE. As a result of this cpufeatures that were detected
and have bits in PSTATE get lost when we resume from idle.
UAO gets set appropriately on the next context switch. PAN will be
re-enabled next time we return from user-space, but on a preemptible
kernel we may run work accessing user space before this point.
Add code to re-enable theses two features in __cpu_suspend_exit().
We re-use uao_thread_switch() passing current.
Signed-off-by: James Morse <james.morse@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The arm64 hw_breakpoint implementation uses a CPU hotplug notifier to
reset the {break,watch}point registers when CPUs come online.
This patch converts the code to the new hotplug mechanism, whilst moving
the invocation earlier to remove the need to disable IRQs explicitly in
the driver (which could cause havok if we trip a watchpoint in an IRQ
handler whilst restoring the debug register state).
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
By enabling the MMU early in cpu_resume(), the sleep_save_sp and stack can
be accessed by VA, which avoids the need to convert-addresses and clean to
PoC on the suspend path.
MMU setup is shared with the boot path, meaning the swapper_pg_dir is
restored directly: ttbr1_el1 is no longer saved/restored.
struct sleep_save_sp is removed, replacing it with a single array of
pointers.
cpu_do_{suspend,resume} could be further reduced to not restore: cpacr_el1,
mdscr_el1, tcr_el1, vbar_el1 and sctlr_el1, all of which are set by
__cpu_setup(). However these values all contain res0 bits that may be used
to enable future features.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Hibernate could make use of the cpu_suspend() code to save/restore cpu
state, however it needs to be able to return '0' from the 'finisher'.
Rework cpu_suspend() so that the finisher is called from C code,
independently from the save/restore of cpu state. Space to save the context
in is allocated in the caller's stack frame, and passed into
__cpu_suspend_enter().
Hibernate's use of this API will look like a copy of the cpu_suspend()
function.
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We currently open-code the removal of the idmap and restoration of the
current task's MMU state in a few places.
Before introducing yet more copies of this sequence, unify these to call
a new helper, cpu_uninstall_idmap.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Laura Abbott <labbott@fedoraproject.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The function graph tracer adds instrumentation that is required to trace
both entry and exit of a function. In particular the function graph
tracer updates the "return address" of a function in order to insert
a trace callback on function exit.
Kernel power management functions like cpu_suspend() are called
upon power down entry with functions called "finishers" that are in turn
called to trigger the power down sequence but they may not return to the
kernel through the normal return path.
When the core resumes from low-power it returns to the cpu_suspend()
function through the cpu_resume path, which leaves the trace stack frame
set-up by the function tracer in an incosistent state upon return to the
kernel when tracing is enabled.
This patch fixes the issue by pausing/resuming the function graph
tracer on the thread executing cpu_suspend() (ie the function call that
subsequently triggers the "suspend finishers"), so that the function graph
tracer state is kept consistent across functions that enter power down
states and never return by effectively disabling graph tracer while they
are executing.
Fixes: 819e50e25d ("arm64: Add ftrace support")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- __cmpxchg_double*() return type fix to avoid truncation of a long to
int and subsequent logical "not" in cmpxchg_double() misinterpreting
the operation success/failure
- BPF fixes for mod and div by zero
- Fix compilation with STRICT_MM_TYPECHECKS enabled
- VDSO build fix without libgcov
- Some static and __maybe_unused annotations
- Kconfig clean-up (FRAME_POINTER)
- defconfig update for CRYPTO_CRC32_ARM64
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ApkD
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes and clean-ups from Catalin Marinas:
"Here's a second pull request for this merging window with some
fixes/clean-ups:
- __cmpxchg_double*() return type fix to avoid truncation of a long
to int and subsequent logical "not" in cmpxchg_double()
misinterpreting the operation success/failure
- BPF fixes for mod and div by zero
- Fix compilation with STRICT_MM_TYPECHECKS enabled
- VDSO build fix without libgcov
- Some static and __maybe_unused annotations
- Kconfig clean-up (FRAME_POINTER)
- defconfig update for CRYPTO_CRC32_ARM64"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: suspend: make hw_breakpoint_restore static
arm64: mmu: make split_pud and fixup_executable static
arm64: smp: make of_parse_and_init_cpus static
arm64: use linux/types.h in kvm.h
arm64: build vdso without libgcov
arm64: mark cpus_have_hwcap as __maybe_unused
arm64: remove redundant FRAME_POINTER kconfig option and force to select it
arm64: fix R/O permissions of FDT mapping
arm64: fix STRICT_MM_TYPECHECKS issue in PTE_CONT manipulation
arm64: bpf: fix mod-by-zero case
arm64: bpf: fix div-by-zero case
arm64: Enable CRYPTO_CRC32_ARM64 in defconfig
arm64: cmpxchg_dbl: fix return value type
hw_breakpoint_restore is only used within suspend.c, so it can be
declared static.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- "genirq: Introduce generic irq migration for cpu hotunplugged" patch
merged from tip/irq/for-arm to allow the arm64-specific part to be
upstreamed via the arm64 tree
- CPU feature detection reworked to cope with heterogeneous systems
where CPUs may not have exactly the same features. The features
reported by the kernel via internal data structures or ELF_HWCAP are
delayed until all the CPUs are up (and before user space starts)
- Support for 16KB pages, with the additional bonus of a 36-bit VA
space, though the latter only depending on EXPERT
- Implement native {relaxed, acquire, release} atomics for arm64
- New ASID allocation algorithm which avoids IPI on roll-over, together
with TLB invalidation optimisations (using local vs global where
feasible)
- KASan support for arm64
- EFI_STUB clean-up and isolation for the kernel proper (required by
KASan)
- copy_{to,from,in}_user optimisations (sharing the memcpy template)
- perf: moving arm64 to the arm32/64 shared PMU framework
- L1_CACHE_BYTES increased to 128 to accommodate Cavium hardware
- Support for the contiguous PTE hint on kernel mapping (16 consecutive
entries may be able to use a single TLB entry)
- Generic CONFIG_HZ now used on arm64
- defconfig updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3six
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- "genirq: Introduce generic irq migration for cpu hotunplugged" patch
merged from tip/irq/for-arm to allow the arm64-specific part to be
upstreamed via the arm64 tree
- CPU feature detection reworked to cope with heterogeneous systems
where CPUs may not have exactly the same features. The features
reported by the kernel via internal data structures or ELF_HWCAP are
delayed until all the CPUs are up (and before user space starts)
- Support for 16KB pages, with the additional bonus of a 36-bit VA
space, though the latter only depending on EXPERT
- Implement native {relaxed, acquire, release} atomics for arm64
- New ASID allocation algorithm which avoids IPI on roll-over, together
with TLB invalidation optimisations (using local vs global where
feasible)
- KASan support for arm64
- EFI_STUB clean-up and isolation for the kernel proper (required by
KASan)
- copy_{to,from,in}_user optimisations (sharing the memcpy template)
- perf: moving arm64 to the arm32/64 shared PMU framework
- L1_CACHE_BYTES increased to 128 to accommodate Cavium hardware
- Support for the contiguous PTE hint on kernel mapping (16 consecutive
entries may be able to use a single TLB entry)
- Generic CONFIG_HZ now used on arm64
- defconfig updates
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (91 commits)
arm64/efi: fix libstub build under CONFIG_MODVERSIONS
ARM64: Enable multi-core scheduler support by default
arm64/efi: move arm64 specific stub C code to libstub
arm64: page-align sections for DEBUG_RODATA
arm64: Fix build with CONFIG_ZONE_DMA=n
arm64: Fix compat register mappings
arm64: Increase the max granular size
arm64: remove bogus TASK_SIZE_64 check
arm64: make Timer Interrupt Frequency selectable
arm64/mm: use PAGE_ALIGNED instead of IS_ALIGNED
arm64: cachetype: fix definitions of ICACHEF_* flags
arm64: cpufeature: declare enable_cpu_capabilities as static
genirq: Make the cpuhotplug migration code less noisy
arm64: Constify hwcap name string arrays
arm64/kvm: Make use of the system wide safe values
arm64/debug: Make use of the system wide safe value
arm64: Move FP/ASIMD hwcap handling to common code
arm64/HWCAP: Use system wide safe values
arm64/capabilities: Make use of system wide safe value
arm64: Delay cpu feature capability checks
...
Commit dd006da216 ("arm64: mm: increase VA range of identity map")
introduced a mechanism to extend the virtual memory map range
to support arm64 systems with system RAM located at very high offset,
where the identity mapping used to enable/disable the MMU requires
additional translation levels to map the physical memory at an equal
virtual offset.
The kernel detects at boot time the tcr_el1.t0sz value required by the
identity mapping and sets-up the tcr_el1.t0sz register field accordingly,
any time the identity map is required in the kernel (ie when enabling the
MMU).
After enabling the MMU, in the cold boot path the kernel resets the
tcr_el1.t0sz to its default value (ie the actual configuration value for
the system virtual address space) so that after enabling the MMU the
memory space translated by ttbr0_el1 is restored as expected.
Commit dd006da216 ("arm64: mm: increase VA range of identity map")
also added code to set-up the tcr_el1.t0sz value when the kernel resumes
from low-power states with the MMU off through cpu_resume() in order to
effectively use the identity mapping to enable the MMU but failed to add
the code required to restore the tcr_el1.t0sz to its default value, when
the core returns to the kernel with the MMU enabled, so that the kernel
might end up running with tcr_el1.t0sz value set-up for the identity
mapping which can be lower than the value required by the actual virtual
address space, resulting in an erroneous set-up.
This patchs adds code in the resume path that restores the tcr_el1.t0sz
default value upon core resume, mirroring this way the cold boot path
behaviour therefore fixing the issue.
Cc: <stable@vger.kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Fixes: dd006da216 ("arm64: mm: increase VA range of identity map")
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
There are a number of places where a single CPU is running with a
private page-table and we need to perform maintenance on the TLB and
I-cache in order to ensure correctness, but do not require the operation
to be broadcast to other CPUs.
This patch adds local variants of tlb_flush_all and __flush_icache_all
to support these use-cases and updates the callers respectively.
__local_flush_icache_all also implies an isb, since it is intended to be
used synchronously.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: David Daney <david.daney@cavium.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch renames __cpu_suspend to cpu_suspend so that it's aligned
with ARM32. It also removes the redundant wrapper created.
This is in preparation to implement generic PSCI system suspend using
the cpu_{suspend,resume} which now has the same interface on both ARM
and ARM64.
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Two cleanups of the asm function cpu_resume():
- The global variable sleep_idmap_phys always points to idmap_pg_dir,
so we can just use that value directly in the CPU resume path.
- Unclutter the load of sleep_save_sp::save_ptr_stash_phys.
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ARM64_CPU_SUSPEND config option was introduced to make code providing
context save/restore selectable only on platforms requiring power
management capabilities.
Currently ARM64_CPU_SUSPEND depends on the PM_SLEEP config option which
in turn is set by the SUSPEND config option.
The introduction of CPU_IDLE for arm64 requires that code configured
by ARM64_CPU_SUSPEND (context save/restore) should be compiled in
in order to enable the CPU idle driver to rely on CPU operations
carrying out context save/restore.
The ARM64_CPUIDLE config option (ARM64 generic idle driver) is therefore
forced to select ARM64_CPU_SUSPEND, even if there may be (ie PM_SLEEP)
failed dependencies, which is not a clean way of handling the kernel
configuration option.
For these reasons, this patch removes the ARM64_CPU_SUSPEND config option
and makes the context save/restore dependent on CPU_PM, which is selected
whenever either SUSPEND or CPU_IDLE are configured, cleaning up dependencies
in the process.
This way, code previously configured through ARM64_CPU_SUSPEND is
compiled in whenever a power management subsystem requires it to be
present in the kernel (SUSPEND || CPU_IDLE), which is the behaviour
expected on ARM64 kernels.
The cpu_suspend and cpu_init_idle CPU operations are added only if
CPU_IDLE is selected, since they are CPU_IDLE specific methods and
should be grouped and defined accordingly.
PSCI CPU operations are updated to reflect the introduced changes.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
On arm64 the TTBR0_EL1 register is set to either the reserved TTBR0
page tables on boot or to the active_mm mappings belonging to user space
processes, it must never be set to swapper_pg_dir page tables mappings.
When a CPU is booted its active_mm is set to init_mm even though its
TTBR0_EL1 points at the reserved TTBR0 page mappings. This implies
that when __cpu_suspend is triggered the active_mm can point at
init_mm even if the current TTBR0_EL1 register contains the reserved
TTBR0_EL1 mappings.
Therefore, the mm save and restore executed in __cpu_suspend might
turn out to be erroneous in that, if the current->active_mm corresponds
to init_mm, on resume from low power it ends up restoring in the
TTBR0_EL1 the init_mm mappings that are global and can cause speculation
of TLB entries which end up being propagated to user space.
This patch fixes the issue by checking the active_mm pointer before
restoring the TTBR0 mappings. If the current active_mm == &init_mm,
the code sets the TTBR0_EL1 to the reserved TTBR0 mapping instead of
switching back to the active_mm, which is the expected behaviour
corresponding to the TTBR0_EL1 settings when __cpu_suspend was entered.
Fixes: 95322526ef ("arm64: kernel: cpu_{suspend/resume} implementation")
Cc: <stable@vger.kernel.org> # 3.14+: 18ab7db
Cc: <stable@vger.kernel.org> # 3.14+: 714f599
Cc: <stable@vger.kernel.org> # 3.14+: c3684fb
Cc: <stable@vger.kernel.org> # 3.14+
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The function cpu_resume currently lives in the .data section.
There's no reason for it to be there since we can use relative
instructions without a problem. Move a few cpu_resume data
structures out of the assembly file so the .data annotation
can be dropped completely and cpu_resume ends up in the read
only text section.
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Kees Cook <keescook@chromium.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
CPU suspend is the standard kernel interface to be used to enter
low-power states on ARM64 systems. Current cpu_suspend implementation
by default assumes that all low power states are losing the CPU context,
so the CPU registers must be saved and cleaned to DRAM upon state
entry. Furthermore, the current cpu_suspend() implementation assumes
that if the CPU suspend back-end method returns when called, this has
to be considered an error regardless of the return code (which can be
successful) since the CPU was not expected to return from a code path that
is different from cpu_resume code path - eg returning from the reset vector.
All in all this means that the current API does not cope well with low-power
states that preserve the CPU context when entered (ie retention states),
since first of all the context is saved for nothing on state entry for
those states and a successful state entry can return as a normal function
return, which is considered an error by the current CPU suspend
implementation.
This patch refactors the cpu_suspend() API so that it can be split in
two separate functionalities. The arm64 cpu_suspend API just provides
a wrapper around CPU suspend operation hook. A new function is
introduced (for architecture code use only) for states that require
context saving upon entry:
__cpu_suspend(unsigned long arg, int (*fn)(unsigned long))
__cpu_suspend() saves the context on function entry and calls the
so called suspend finisher (ie fn) to complete the suspend operation.
The finisher is not expected to return, unless it fails in which case
the error is propagated back to the __cpu_suspend caller.
The API refactoring results in the following pseudo code call sequence for a
suspending CPU, when triggered from a kernel subsystem:
/*
* int cpu_suspend(unsigned long idx)
* @idx: idle state index
*/
{
-> cpu_suspend(idx)
|---> CPU operations suspend hook called, if present
|--> if (retention_state)
|--> direct suspend back-end call (eg PSCI suspend)
else
|--> __cpu_suspend(idx, &back_end_finisher);
}
By refactoring the cpu_suspend API this way, the CPU operations back-end
has a chance to detect whether idle states require state saving or not
and can call the required suspend operations accordingly either through
simple function call or indirectly through __cpu_suspend() which carries out
state saving and suspend finisher dispatching to complete idle state entry.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Suspend init function must be marked as __init, since it is not needed
after the kernel has booted. This patch moves the cpu_suspend_init()
function to the __init section.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The introduction of percpu offset optimisation through tpidr_el1 in:
Commit id :7158627686f02319c50c8d9d78f75d4c8
"arm64: percpu: implement optimised pcpu access using tpidr_el1"
requires cpu_{suspend/resume} to restore the tpidr_el1 register upon resume
so that percpu variables can be addressed correctly when a CPU comes out
of reset from warm-boot.
This patch fixes cpu_{suspend}/{resume} tpidr_el1 restoration on resume, by
calling the set_my_cpu_offset C API, as it is done on primary and secondary
CPUs on cold boot, so that, even if the register used to store the percpu
offset is changed, the save and restore of general purpose registers does not
have to be updated.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When a CPU resumes from low-power, it restores HW breakpoint and
watchpoint slots through a CPU PM notifier. Since we want to enable
debugging as early as possible in the resume path, the mdscr content
is restored along the general purpose registers in the cpu_suspend API
and debug exceptions are reenabled when cpu_suspend returns. Since the
CPU PM notifier is run after a CPU has been resumed, we cannot expect
HW breakpoint registers to contain sane values till the notifier is run,
since the HW breakpoints registers content is unknown at reset; this means
that the CPU might run with debug exceptions enabled, mdscr restored but HW
breakpoint registers containing junk values that can trigger spurious
debug exceptions.
This patch fixes current HW breakpoints restore by moving the HW breakpoints
registers restoration to the cpu_suspend API, before the debug exceptions are
enabled. This way, as soon as the cpu_suspend function returns the
kernel can resume debugging with sane values in HW breakpoint registers.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Kernel subsystems like CPU idle and suspend to RAM require a generic
mechanism to suspend a processor, save its context and put it into
a quiescent state. The cpu_{suspend}/{resume} implementation provides
such a framework through a kernel interface allowing to save/restore
registers, flush the context to DRAM and suspend/resume to/from
low-power states where processor context may be lost.
The CPU suspend implementation relies on the suspend protocol registered
in CPU operations to carry out a suspend request after context is
saved and flushed to DRAM. The cpu_suspend interface:
int cpu_suspend(unsigned long arg);
allows to pass an opaque parameter that is handed over to the suspend CPU
operations back-end so that it can take action according to the
semantics attached to it. The arg parameter allows suspend to RAM and CPU
idle drivers to communicate to suspend protocol back-ends; it requires
standardization so that the interface can be reused seamlessly across
systems, paving the way for generic drivers.
Context memory is allocated on the stack, whose address is stashed in a
per-cpu variable to keep track of it and passed to core functions that
save/restore the registers required by the architecture.
Even though, upon successful execution, the cpu_suspend function shuts
down the suspending processor, the warm boot resume mechanism, based
on the cpu_resume function, makes the resume path operate as a
cpu_suspend function return, so that cpu_suspend can be treated as a C
function by the caller, which simplifies coding the PM drivers that rely
on the cpu_suspend API.
Upon context save, the minimal amount of memory is flushed to DRAM so
that it can be retrieved when the MMU is off and caches are not searched.
The suspend CPU operation, depending on the required operations (eg CPU vs
Cluster shutdown) is in charge of flushing the cache hierarchy either
implicitly (by calling firmware implementations like PSCI) or explicitly
by executing the required cache maintainance functions.
Debug exceptions are disabled during cpu_{suspend}/{resume} operations
so that debug registers can be saved and restored properly preventing
preemption from debug agents enabled in the kernel.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
