Add DMA entry for main_spi0, that has SPI flash connected, for better
throughput and reduced CPU load.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The TI sci-clk driver can scan the DT for all clocks provided by system
firmware and does this by checking the clocks property of all nodes, so
we must add this to the dwc3 nodes so USB clocks are available.
Without this USB does not work with latest system firmware i.e.
[ 1.714662] clk: couldn't get parent clock 0 for /interconnect@100000/dwc3@4020000
Fixes: cc54a99464 ("arm64: dts: ti: k3-am6: add USB suppor")
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: stable@kernel.org
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Enabling KASLR forces the use of non-global page-table entries for kernel
mappings, as this is a decision that we have to make very early on before
mapping the kernel proper. When used in conjunction with the "kpti=off"
command-line option, it is possible to use non-global kernel mappings but
with the kpti trampoline disabled.
Since commit 09e3c22a86 ("arm64: Use a variable to store non-global
mappings decision"), arm64_kernel_unmapped_at_el0() reflects only the use of
non-global mappings and does not take into account whether the kpti
trampoline is enabled. This breaks context switching of the TPIDRRO_EL0
register for 64-bit tasks, where the clearing of the register is deferred to
the ret-to-user code, but it also breaks the ARM SPE PMU driver which
helpfully recommends passing "kpti=off" on the command line!
Report whether or not KPTI is actually enabled in
arm64_kernel_unmapped_at_el0() and check the 'arm64_use_ng_mappings' global
variable directly when determining the protection flags for kernel mappings.
Cc: Mark Brown <broonie@kernel.org>
Reported-by: Hongbo Yao <yaohongbo@huawei.com>
Tested-by: Hongbo Yao <yaohongbo@huawei.com>
Fixes: 09e3c22a86 ("arm64: Use a variable to store non-global mappings decision")
Signed-off-by: Will Deacon <will@kernel.org>
Compile all functions with two ptrauth instructions: PACIASP in the
prologue to sign the return address, and AUTIASP in the epilogue to
authenticate the return address (from the stack). If authentication
fails, the return will cause an instruction abort to be taken, followed
by an oops and killing the task.
This should help protect the kernel against attacks using
return-oriented programming. As ptrauth protects the return address, it
can also serve as a replacement for CONFIG_STACKPROTECTOR, although note
that it does not protect other parts of the stack.
The new instructions are in the HINT encoding space, so on a system
without ptrauth they execute as NOPs.
CONFIG_ARM64_PTR_AUTH now not only enables ptrauth for userspace and KVM
guests, but also automatically builds the kernel with ptrauth
instructions if the compiler supports it. If there is no compiler
support, we do not warn that the kernel was built without ptrauth
instructions.
GCC 7 and 8 support the -msign-return-address option, while GCC 9
deprecates that option and replaces it with -mbranch-protection. Support
both options.
Clang uses an external assembler hence this patch makes sure that the
correct parameters (-march=armv8.3-a) are passed down to help it recognize
the ptrauth instructions.
Ftrace function tracer works properly with Ptrauth only when
patchable-function-entry feature is present and is ensured by the
Kconfig dependency.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Vincenzo Frascino <Vincenzo.Frascino@arm.com> # not co-dev parts
Co-developed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[Amit: Cover leaf function, comments, Ftrace Kconfig]
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch restores the kernel keys from current task during cpu resume
after the mmu is turned on and ptrauth is enabled.
A flag is added in macro ptrauth_keys_install_kernel to check if isb
instruction needs to be executed.
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Reviewed-by: Vincenzo Frascino <Vincenzo.Frascino@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
lr is printed with %pS which will try to find an entry in kallsyms.
After enabling pointer authentication, this match will fail due to
PAC present in the lr.
Strip PAC from the lr to display the correct symbol name.
Suggested-by: James Morse <james.morse@arm.com>
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Reviewed-by: Vincenzo Frascino <Vincenzo.Frascino@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When we enable pointer authentication in the kernel, LR values saved to
the stack will have a PAC which we must strip in order to retrieve the
real return address.
Strip PACs when unwinding the stack in order to account for this.
When function graph tracer is used with patchable-function-entry then
return_to_handler will also have pac bits so strip it too.
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[Amit: Re-position ptrauth_strip_insn_pac, comment]
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Functions like vmap() record how much memory has been allocated by their
callers, and callers are identified using __builtin_return_address(). Once
the kernel is using pointer-auth the return address will be signed. This
means it will not match any kernel symbol, and will vary between threads
even for the same caller.
The output of /proc/vmallocinfo in this case may look like,
0x(____ptrval____)-0x(____ptrval____) 20480 0x86e28000100e7c60 pages=4 vmalloc N0=4
0x(____ptrval____)-0x(____ptrval____) 20480 0x86e28000100e7c60 pages=4 vmalloc N0=4
0x(____ptrval____)-0x(____ptrval____) 20480 0xc5c78000100e7c60 pages=4 vmalloc N0=4
The above three 64bit values should be the same symbol name and not
different LR values.
Use the pre-processor to add logic to clear the PAC to
__builtin_return_address() callers. This patch adds a new file
asm/compiler.h and is transitively included via include/compiler_types.h on
the compiler command line so it is guaranteed to be loaded and the users of
this macro will not find a wrong version.
Helper macros ptrauth_kernel_pac_mask/ptrauth_clear_pac are created for
this purpose and added in this file. Existing macro ptrauth_user_pac_mask
moved from asm/pointer_auth.h.
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch uses the existing boot_init_stack_canary arch function
to initialize the ptrauth keys for the booting task in the primary
core. The requirement here is that it should be always inline and
the caller must never return.
As pointer authentication too detects a subset of stack corruption
so it makes sense to place this code here.
Both pointer authentication and stack canary codes are protected
by their respective config option.
Suggested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Reviewed-by: Vincenzo Frascino <Vincenzo.Frascino@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Set up keys to use pointer authentication within the kernel. The kernel
will be compiled with APIAKey instructions, the other keys are currently
unused. Each task is given its own APIAKey, which is initialized during
fork. The key is changed during context switch and on kernel entry from
EL0.
The keys for idle threads need to be set before calling any C functions,
because it is not possible to enter and exit a function with different
keys.
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Vincenzo Frascino <Vincenzo.Frascino@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[Amit: Modified secondary cores key structure, comments]
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When the kernel is compiled with pointer auth instructions, the boot CPU
needs to start using address auth very early, so change the cpucap to
account for this.
Pointer auth must be enabled before we call C functions, because it is
not possible to enter a function with pointer auth disabled and exit it
with pointer auth enabled. Note, mismatches between architected and
IMPDEF algorithms will still be caught by the cpufeature framework (the
separate *_ARCH and *_IMP_DEF cpucaps).
Note the change in behavior: if the boot CPU has address auth and a
late CPU does not, then the late CPU is parked by the cpufeature
framework. This is possible as kernel will only have NOP space intructions
for PAC so such mismatched late cpu will silently ignore those
instructions in C functions. Also, if the boot CPU does not have address
auth and the late CPU has then the late cpu will still boot but with
ptrauth feature disabled.
Leave generic authentication as a "system scope" cpucap for now, since
initially the kernel will only use address authentication.
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Vincenzo Frascino <Vincenzo.Frascino@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[Amit: Re-worked ptrauth setup logic, comments]
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Each system capability can be of either boot, local, or system scope,
depending on when the state of the capability is finalized. When we
detect a conflict on a late CPU, we either offline the CPU or panic the
system. We currently always panic if the conflict is caused by a boot
scope capability, and offline the CPU if the conflict is caused by a
local or system scope capability.
We're going to want to add a new capability (for pointer authentication)
which needs to be boot scope but doesn't need to panic the system when a
conflict is detected. So add a new flag to specify whether the
capability requires the system to panic or not. Current boot scope
capabilities are updated to set the flag, so there should be no
functional change as a result of this patch.
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
These helpers are used only by functions inside cpufeature.c and
hence makes sense to be moved from cpufeature.h to cpufeature.c as
they are not expected to be used globally.
This change helps in reducing the header file size as well as to add
future cpu capability types without confusion. Only a cpu capability
type macro is sufficient to expose those capabilities globally.
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Reviewed-by: Vincenzo Frascino <Vincenzo.Frascino@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch allows __cpu_setup to be invoked with one of these flags,
ARM64_CPU_BOOT_PRIMARY, ARM64_CPU_BOOT_SECONDARY or ARM64_CPU_RUNTIME.
This is required as some cpufeatures need different handling during
different scenarios.
The input parameter in x0 is preserved till the end to be used inside
this function.
There should be no functional change with this patch and is useful
for the subsequent ptrauth patch which utilizes it. Some upcoming
arm cpufeatures can also utilize these flags.
Suggested-by: James Morse <james.morse@arm.com>
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Reviewed-by: Vincenzo Frascino <Vincenzo.Frascino@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
As we're going to enable pointer auth within the kernel and use a
different APIAKey for the kernel itself, so move the user APIAKey
switch to EL0 exception return.
The other 4 keys could remain switched during task switch, but are also
moved to keep things consistent.
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: James Morse <james.morse@arm.com>
Reviewed-by: Vincenzo Frascino <Vincenzo.Frascino@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[Amit: commit msg, re-positioned the patch, comments]
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We currently enable ptrauth for userspace, but do not use it within the
kernel. We're going to enable it for the kernel, and will need to manage
a separate set of ptrauth keys for the kernel.
We currently keep all 5 keys in struct ptrauth_keys. However, as the
kernel will only need to use 1 key, it is a bit wasteful to allocate a
whole ptrauth_keys struct for every thread.
Therefore, a subsequent patch will define a separate struct, with only 1
key, for the kernel. In preparation for that, rename the existing struct
(and associated macros and functions) to reflect that they are specific
to userspace.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Vincenzo Frascino <Vincenzo.Frascino@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[Amit: Re-positioned the patch to reduce the diff]
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
To enable pointer auth for the kernel, we're going to need to check for
the presence of address auth and generic auth using alternative_if. We
currently have two cpucaps for each, but alternative_if needs to check a
single cpucap. So define meta-capabilities that are present when either
of the current two capabilities is present.
Leave the existing four cpucaps in place, as they are still needed to
check for mismatched systems where one CPU has the architected algorithm
but another has the IMP DEF algorithm.
Note, the meta-capabilities were present before but were removed in
commit a56005d321 ("arm64: cpufeature: Reduce number of pointer auth
CPU caps from 6 to 4") and commit 1e013d0612 ("arm64: cpufeature: Rework
ptr auth hwcaps using multi_entry_cap_matches"), as they were not needed
then. Note, unlike before, the current patch checks the cpucap values
directly, instead of reading the CPU ID register value.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Vincenzo Frascino <Vincenzo.Frascino@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[Amit: commit message and macro rebase, use __system_matches_cap]
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Some existing/future meta cpucaps match need the presence of individual
cpucaps. Currently the individual cpucaps checks it via an array based
flag and this introduces dependency on the array entry order.
This limitation exists only for system scope cpufeature.
This patch introduces an internal helper function (__system_matches_cap)
to invoke the matching handler for system scope. This helper has to be
used during a narrow window when,
- The system wide safe registers are set with all the SMP CPUs and,
- The SYSTEM_FEATURE cpu_hwcaps may not have been set.
Normal users should use the existing cpus_have_{const_}cap() global
function.
Suggested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@arm.com>
Reviewed-by: Vincenzo Frascino <Vincenzo.Frascino@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
On a system configured to trigger a crash_kexec() reboot, when only one CPU
is online and another CPU panics while starting-up, crash_smp_send_stop()
will fail to send any STOP message to the other already online core,
resulting in fail to freeze and registers not properly saved.
Moreover even if the proper messages are sent (case CPUs > 2)
it will similarly fail to account for the booting CPU when executing
the final stop wait-loop, so potentially resulting in some CPU not
been waited for shutdown before rebooting.
A tangible effect of this behaviour can be observed when, after a panic
with kexec enabled and loaded, on the following reboot triggered by kexec,
the cpu that could not be successfully stopped fails to come back online:
[ 362.291022] ------------[ cut here ]------------
[ 362.291525] kernel BUG at arch/arm64/kernel/cpufeature.c:886!
[ 362.292023] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[ 362.292400] Modules linked in:
[ 362.292970] CPU: 3 PID: 0 Comm: swapper/3 Kdump: loaded Not tainted 5.6.0-rc4-00003-gc780b890948a #105
[ 362.293136] Hardware name: Foundation-v8A (DT)
[ 362.293382] pstate: 200001c5 (nzCv dAIF -PAN -UAO)
[ 362.294063] pc : has_cpuid_feature+0xf0/0x348
[ 362.294177] lr : verify_local_elf_hwcaps+0x84/0xe8
[ 362.294280] sp : ffff800011b1bf60
[ 362.294362] x29: ffff800011b1bf60 x28: 0000000000000000
[ 362.294534] x27: 0000000000000000 x26: 0000000000000000
[ 362.294631] x25: 0000000000000000 x24: ffff80001189a25c
[ 362.294718] x23: 0000000000000000 x22: 0000000000000000
[ 362.294803] x21: ffff8000114aa018 x20: ffff800011156a00
[ 362.294897] x19: ffff800010c944a0 x18: 0000000000000004
[ 362.294987] x17: 0000000000000000 x16: 0000000000000000
[ 362.295073] x15: 00004e53b831ae3c x14: 00004e53b831ae3c
[ 362.295165] x13: 0000000000000384 x12: 0000000000000000
[ 362.295251] x11: 0000000000000000 x10: 00400032b5503510
[ 362.295334] x9 : 0000000000000000 x8 : ffff800010c7e204
[ 362.295426] x7 : 00000000410fd0f0 x6 : 0000000000000001
[ 362.295508] x5 : 00000000410fd0f0 x4 : 0000000000000000
[ 362.295592] x3 : 0000000000000000 x2 : ffff8000100939d8
[ 362.295683] x1 : 0000000000180420 x0 : 0000000000180480
[ 362.296011] Call trace:
[ 362.296257] has_cpuid_feature+0xf0/0x348
[ 362.296350] verify_local_elf_hwcaps+0x84/0xe8
[ 362.296424] check_local_cpu_capabilities+0x44/0x128
[ 362.296497] secondary_start_kernel+0xf4/0x188
[ 362.296998] Code: 52805001 72a00301 6b01001f 54000ec0 (d4210000)
[ 362.298652] SMP: stopping secondary CPUs
[ 362.300615] Starting crashdump kernel...
[ 362.301168] Bye!
[ 0.000000] Booting Linux on physical CPU 0x0000000003 [0x410fd0f0]
[ 0.000000] Linux version 5.6.0-rc4-00003-gc780b890948a (crimar01@e120937-lin) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36))) #105 SMP PREEMPT Fri Mar 6 17:00:42 GMT 2020
[ 0.000000] Machine model: Foundation-v8A
[ 0.000000] earlycon: pl11 at MMIO 0x000000001c090000 (options '')
[ 0.000000] printk: bootconsole [pl11] enabled
.....
[ 0.138024] rcu: Hierarchical SRCU implementation.
[ 0.153472] its@2f020000: unable to locate ITS domain
[ 0.154078] its@2f020000: Unable to locate ITS domain
[ 0.157541] EFI services will not be available.
[ 0.175395] smp: Bringing up secondary CPUs ...
[ 0.209182] psci: failed to boot CPU1 (-22)
[ 0.209377] CPU1: failed to boot: -22
[ 0.274598] Detected PIPT I-cache on CPU2
[ 0.278707] GICv3: CPU2: found redistributor 1 region 0:0x000000002f120000
[ 0.285212] CPU2: Booted secondary processor 0x0000000001 [0x410fd0f0]
[ 0.369053] Detected PIPT I-cache on CPU3
[ 0.372947] GICv3: CPU3: found redistributor 2 region 0:0x000000002f140000
[ 0.378664] CPU3: Booted secondary processor 0x0000000002 [0x410fd0f0]
[ 0.401707] smp: Brought up 1 node, 3 CPUs
[ 0.404057] SMP: Total of 3 processors activated.
Make crash_smp_send_stop() account also for the online status of the
calling CPU while evaluating how many CPUs are effectively online: this way
the right number of STOPs is sent and all other stopped-cores's registers
are properly saved.
Fixes: 78fd584cde ("arm64: kdump: implement machine_crash_shutdown()")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
At present ARMv8 event counters are limited to 32-bits, though by
using the CHAIN event it's possible to combine adjacent counters to
achieve 64-bits. The perf config1:0 bit can be set to use such a
configuration.
With the introduction of ARMv8.5-PMU support, all event counters can
now be used as 64-bit counters.
Let's enable 64-bit event counters where support exists. Unless the
user sets config1:0 we will adjust the counter value such that it
overflows upon 32-bit overflow. This follows the same behaviour as
the cycle counter which has always been (and remains) 64-bits.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[Mark: fix ID field names, compare with 8.5 value]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
We currently expose the PMU version of the host to the guest via
emulation of the DFR0_EL1 and AA64DFR0_EL1 debug feature registers.
However many of the features offered beyond PMUv3 for 8.1 are not
supported in KVM. Examples of this include support for the PMMIR
registers (added in PMUv3 for ARMv8.4) and 64-bit event counters
added in (PMUv3 for ARMv8.5).
Let's trap the Debug Feature Registers in order to limit
PMUVer/PerfMon in the Debug Feature Registers to PMUv3 for ARMv8.1
to avoid unexpected behaviour.
Both ID_AA64DFR0.PMUVer and ID_DFR0.PerfMon follow the "Alternative ID
scheme used for the Performance Monitors Extension version" where 0xF
means an IMPLEMENTATION DEFINED PMU is implemented, and values 0x0-0xE
are treated as with an unsigned field (with 0x0 meaning no PMU is
present). As we don't expect to expose an IMPLEMENTATION DEFINED PMU,
and our cap is below 0xF, we can treat these fields as unsigned when
applying the cap.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[Mark: make field names consistent, use perfmon cap]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
When emulating ID registers there is often a need to cap the version
bits of a feature such that the guest will not use features that the
host is not aware of. For example, when KVM mediates access to the PMU
by emulating register accesses.
Let's add a helper that extracts a performance monitors ID field and
caps the version to a given value.
Fields that identify the version of the Performance Monitors Extension
do not follow the standard ID scheme, and instead follow the scheme
described in ARM DDI 0487E.a page D13-2825 "Alternative ID scheme used
for the Performance Monitors Extension version". The value 0xF means an
IMPLEMENTATION DEFINED PMU is present, and values 0x0-OxE can be treated
the same as an unsigned field with 0x0 meaning no PMU is present.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[Mark: rework to handle perfmon fields]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Reading this code bordered on painful, what with all the repetition and
pointless return values. More fundamentally, dribbling the hardware
enables and disables in one bit at a time incurs needless system
register overhead for chained events and on reset. We already use
bitmask values for the KVM hooks, so consolidate all the register
accesses to match, and make a reasonable saving in both source and
object code.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Add disabled SPIFC controller node with instruction on how to enable
it while lowering capabilities of the eMMC controller from 8bits bus
width to 4bits bus width, it's data pins 4 to 7 being shared with
the SPI NOR controller pins.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200313090713.15147-5-narmstrong@baylibre.com
Add disabled SPIFC controller node with instruction on how to enable
it while lowering capabilities of the eMMC controller from 8bits bus
width to 4bits bus width, it's data pins 4 to 7 being shared with
the SPI NOR controller pins.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200313090713.15147-4-narmstrong@baylibre.com
Add the controller and pinctrl nodes to enable the SPI Flash Controller
on the Amlogic G12A and compatible SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200313090713.15147-3-narmstrong@baylibre.com
The Khadas VIM3 shares the eMMC pins 4 to 7 with the SPI NOR, in order
to enable the eMMC and the SPI NOR interface, we need to omit the
4 last pins from the eMMC pinctrl.
As it was done for the Khadas VIM2, split the eMMC pinctrls in ctrl, data
and ds pins with either 4bits data or 8bits data, and update the current
board accordingly.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200313090713.15147-2-narmstrong@baylibre.com
When running the kernel with init_on_alloc=1, calling the default
implementation of __alloc_zeroed_user_highpage() from include/linux/highmem.h
leads to double-initialization of the allocated page (first by the page
allocator, then by clear_user_page().
Calling alloc_page_vma() with __GFP_ZERO, similarly to e.g. x86, seems
to be enough to ensure the user page is zeroed only once.
Signed-off-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The function __cpu_up() is invoked to bring up the target CPU through
the backend, PSCI for example. The nested if statements won't be needed
if we bail out early on the following two conditions where the status
won't be checked. The code looks simplified in that case.
* Error returned from the backend (e.g. PSCI)
* The target CPU has been marked as onlined
Signed-off-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
remove redundant blank for '=' operator, it may be more elegant.
Signed-off-by: hankecai <hankecai@vivo.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
add blank after 'if' for armv8_deprecated_init()
to make it comply with kernel coding style.
Signed-off-by: Zheng Wei <wei.zheng@vivo.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
There is a spelling mistake in the comment, Fix it.
Signed-off-by: hankecai <hankecai@bbktel.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add IPA-related nodes and definitions to "sdm845.dtsi".
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20200313115237.10491-2-elder@linaro.org
[bjorn: Moved modem-init to cheza.dtsi]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Remove pwm0 node as it interferes with power LED gpio.
Tested with LibreElec linux-next-20200305
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Link: https://lore.kernel.org/r/20200313230513.123049-1-npcomplete13@gmail.com
[split out led addition into separate patch]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
arch/arm64/boot/dts/rockchip/rk3328-evb.dt.yaml: usb@ff5d0000:
'clock-names' does not match any of the regexes: 'pinctrl-[0-9]+'
'clock-names' is not a valid property name for usb_host nodes with
compatible string 'generic-ohci', so remove them.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/usb/generic-ohci.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200312171441.21144-4-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
arch/arm64/boot/dts/rockchip/rk3328-evb.dt.yaml: usb@ff5c0000:
'clock-names' does not match any of the regexes: 'pinctrl-[0-9]+'
'clock-names' is not a valid property name for usb_host nodes with
compatible string 'generic-ehci', so remove them.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/usb/generic-ehci.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200312171441.21144-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
An expermental test with the command below gives this error:
arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator.dt.yaml:
spdif@ff870000:
'i2c-scl-falling-time-ns', 'i2c-scl-rising-time-ns', 'power-domains'
do not match any of the regexes: 'pinctrl-[0-9]+'
'i2c-scl-falling-time-ns', 'i2c-scl-rising-time-ns'
are not valid properties for 'spdif' nodes, so remove them.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/sound/rockchip-spdif.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200312172240.21362-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The correct setting for the RGMII ports on LS1046ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit 1b3047b520 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1046ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii".
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: 3fa395d2c4 ("arm64: dts: add LS1046A DPAA FMan nodes")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct setting for the RGMII ports on LS1043ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit 1b3047b520 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1043ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii_txid".
This issue was not apparent at the time as the PHY driver took the
same action for RGMII_TXID and RGMII_ID back then but it became
visible (RX no longer working) after the above patch.
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: bf02f2ffe5 ("arm64: dts: add LS1043A DPAA FMan support")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Allow to disable gisa
2. protected virtual machines
Protected VMs (PVM) are KVM VMs, where KVM can't access the VM's
state like guest memory and guest registers anymore. Instead the
PVMs are mostly managed by a new entity called Ultravisor (UV),
which provides an API, so KVM and the PV can request management
actions.
PVMs are encrypted at rest and protected from hypervisor access
while running. They switch from a normal operation into protected
mode, so we can still use the standard boot process to load a
encrypted blob and then move it into protected mode.
Rebooting is only possible by passing through the unprotected/normal
mode and switching to protected again.
One mm related patch will go via Andrews mm tree ( mm/gup/writeback:
add callbacks for inaccessible pages)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=x6Hn
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: Features and Enhancements for 5.7 part1
1. Allow to disable gisa
2. protected virtual machines
Protected VMs (PVM) are KVM VMs, where KVM can't access the VM's
state like guest memory and guest registers anymore. Instead the
PVMs are mostly managed by a new entity called Ultravisor (UV),
which provides an API, so KVM and the PV can request management
actions.
PVMs are encrypted at rest and protected from hypervisor access
while running. They switch from a normal operation into protected
mode, so we can still use the standard boot process to load a
encrypted blob and then move it into protected mode.
Rebooting is only possible by passing through the unprotected/normal
mode and switching to protected again.
One mm related patch will go via Andrews mm tree ( mm/gup/writeback:
add callbacks for inaccessible pages)
Remove includes of asm/kvm_host.h from files that already include
linux/kvm_host.h to make it more obvious that there is no ordering issue
between the two headers. linux/kvm_host.h includes asm/kvm_host.h to
pick up architecture specific settings, and this will never change, i.e.
including asm/kvm_host.h after linux/kvm_host.h may seem problematic,
but in practice is simply redundant.
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Adapt and update current VIM2 thermal zones support so that zones are
available on all meson GXBB/GXL/GXM devices - similar to changes made
for G12A/G12B/SM1 devices.
Suggested-by: Nick Xie <nick@khadas.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/1584328854-28575-1-git-send-email-christianshewitt@gmail.com
The common meson-khadas-vim3.dtsi is now shared with VIM3L so move the
VIM3 model name to meson-g12b-khadas-vim3.dtsi.
meson-sm1-khadas-vim3l.dts contains the VIM3L model name.
changes in v2
- fix typo in commit message
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/1583378508-14312-1-git-send-email-christianshewitt@gmail.com
Currently common clock and reset IDs were used, however, each clock and
reset ID should be used for each channel.
Fixes: 925c5c32f3 ("arm64: dts: uniphier: add SPI node for LD20, LD11 and PXs3")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add nodes of thermal monitor and thermal zone for UniPhier PXs3 SoC.
The thermal monitor node is included in sysctrl. This patch gives the
default value for PXs3 in the same way as LD20.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
PXs3 reference board has 2 spi connectors. This enables spi0 and spi1,
and adds aliases properties for each spi to determine device name
assignments.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Disable the felix switch by default and enable it per board which are
actually using it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that there is support for the Felix switch this variant can also be
added. It features two external ports ethernet ports which are connected
to the internal switch core. No direct connection to any of the enetc's
is supported.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The KBox A-230-LS supports four external ports which are connected to
the internal switch of the LS1028A via QSGMII. Now that the Felix switch
is supported, add these ports in the device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The module itself has another EEPROM at 50h on I2C4. The EEPROM on the
carriers is located at 57h on I2C3. Fix that in the device trees.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is a SPI flash on this carrier connected to the third DSPI
controller. Add it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per binding doc fsl,aips-bus.yaml, compatible and reg is
required. And for reg, the AIPS configuration space should be
used, not all the AIPS bus space.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable soundwire, slimbus frameworks, the machine driver and the codec
drivers for WCD934x and WSA881x used on varios SDM845 based designs.
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200315050827.1575421-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Enables e1000 Ethernet device as it is used as a low-cost failover
Ethernet port on various QorIQ reference boards. Enabled as built-in
for booting from network without initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables various PHY device drivers and PHY MUX drivers used on QorIQ
reference boards supported in mainline kernel.
Enabled as built-in to boot from network without an initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables the RTC devices used on QorIQ reference boards supported in
mainline kernel.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the flash devices used on NXP/FSL QorIQ reference boards
supported in mainline kernel. Drivers are enabled as built-in for RFS
access without initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables the Mali display driver for the display port on NXP LS1028a SoC.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables generic GPIO driver for varous QorIQ SoCs. The driver can only
be built-in right now.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables NXP/FSL QorIQ IFC flash controller driver for NAND. Enabled as
built-in to load RFS from nand flash without initramfs.
Remove CONFIG_MEMORY as it is selected by CONFIG_MTD_NAND_FSL_IFC.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables ARM generic SBSA compatible watchdog driver for NXP LX2160a SoC.
Enabled as built-in for it is a core feature.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables the generic QorIQ cpufreq driver to support frequency scaling
for various QorIQ SoCs. Enabled as built-in as it is a core feature.
Remove CONFIG_CLK_QORIQ as it is seleted by CONFIG_QORIQ_CPUFREQ.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables SPI controller drivers used in various NXP/FSL SoCs.
QSPI is fast enough to connect big flash for file system. It is used to
connect 512MB NAND flash and 256MB NOR flash on LS1028RDB. It is used
as bootsource for other platforms like LS2080ardb too. Enabled as
built-in to load RFS from SPI flash without requiring initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables drivers for NXP ENETC Ethernet controller and FELIX Ethernet
switch used on QorIQ LS1028a SoC.
The ENETC ethernet drivers are enabled as built-in to boot from network
without an initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables drivers for NXP DPAA2 framework, related Ethernet and crypto
device which can be found on QorIQ SoCs like LS1088a, LS2088a and
LX2160a.
The framework and ethernet drivers are enabled as built-in to boot
from network without an initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables drivers for NXP DPAA1 framework and related Ethernet device which
can be found on QorIQ SoCs such as LS1043a and LS1046a. They are enabled
as built-in to boot from network without an initramfs.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables driver for FLEXCAN device which is used on a wide range of NXP
SoCs. Also enabling the related CAN framework.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Used "make defconfig savedefconfig" to regenerate defconfig files in the
right order to prepare for additional defconfig changes.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MN shares same thermal sensor with i.MX8MM, add thermal zone
support for i.MX8MN.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
make -k ARCH=arm64 dtbs_check shows the following errors. Fix them by
removing the "arm,armv8" compatible.
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@0: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@0: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long CHECK
arch/arm64/boot/dts/renesas/r8a774a1-hihope-rzg2m-ex.dt.yaml
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@1: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@1: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@100: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@100: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@101: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9130-db.dt.yaml:
cpu@101: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@0: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@0: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@1: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@1: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@100: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@100: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@101: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9131-db.dt.yaml:
cpu@101: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@0: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@0: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@1: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@1: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@100: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@100: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@101: compatible: Additional items are not allowed ('arm,armv8' was
unexpected)
/home/amit/work/builds/build-check/arch/arm64/boot/dts/marvell/cn9132-db.dt.yaml:
cpu@101: compatible: ['arm,cortex-a72', 'arm,armv8'] is too long
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
armada-ap806-dual.dtsi includes armada-ap806.dtsi which describes
thermal zones for 4 cpus but only cpu0 and cpu1 only exists for dual
configuration, this makes dtb compilation fail. Fix it by removing
thermal zone nodes for non-existed cpus for dual configuration.
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The commit adding ESPRESSObin variants didn't include those in Makefile to
be built.
Fixes: 447b878935 ("arm64: dts: marvell: add ESPRESSObin variants")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The commit introducing ESPRESSObin variants didn't specify dts version,
and because of that they are treated by dtc as legacy ones. Fix that by
properly specifying version in each dts.
Fixes: 447b878935 ("arm64: dts: marvell: add ESPRESSObin variants")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The maker of this board and its variants, stores MAC address in U-Boot
environment. Add alias for bootloader to recognise, to which ethernet
node inject the factory MAC address.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Allow the SFP cages to be used with 2W SFP modules.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
If the mv88e6xxx DSA driver is built as a module, it causes the
ethernet driver to re-probe when it's loaded. This in turn causes
the gigabit PHY to be momentarily reset and reprogrammed. However,
we attempt to reprogram the PHY immediately after deasserting reset,
and the PHY ignores the writes.
This results in the PHY operating in the wrong mode, and the copper
link states down.
Set a reset deassert delay of 10ms for the gigabit PHY to avoid this.
Fixes: babc5544c2 ("arm64: dts: clearfog-gt-8k: 1G eth PHY reset signal")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The KVM hyp code is only run after system capabilities have been
finalized, and thus all const cap checks have been patched. This is
noted in in __cpu_init_hyp_mode(), where we BUG() if called too early:
| /*
| * Call initialization code, and switch to the full blown HYP code.
| * If the cpucaps haven't been finalized yet, something has gone very
| * wrong, and hyp will crash and burn when it uses any
| * cpus_have_const_cap() wrapper.
| */
Given this, the hyp code can use cpus_have_final_cap() and avoid
generating code to check the cpu_hwcaps array, which would be unsafe to
run in hyp context.
This patch migrate the KVM hyp code to cpus_have_final_cap(), avoiding
this redundant code generation, and making it possible to detect if we
accidentally invoke this code too early. In the latter case, the BUG()
in cpus_have_final_cap() will cause a hyp panic.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Julien Thierry <julien.thierry.kdev@gmail.com>
Cc: Suzuki Poulouse <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When cpus_have_const_cap() was originally introduced it was intended to
be safe in hyp context, where it is not safe to access the cpu_hwcaps
array as cpus_have_cap() did. For more details see commit:
a4023f6827 ("arm64: Add hypervisor safe helper for checking constant capabilities")
We then made use of cpus_have_const_cap() throughout the kernel.
Subsequently, we had to defer updating the static_key associated with
each capability in order to avoid lockdep complaints. To avoid breaking
kernel-wide usage of cpus_have_const_cap(), this was updated to fall
back to the cpu_hwcaps array if called before the static_keys were
updated. As the kvm hyp code was only called later than this, the
fallback is redundant but not functionally harmful. For more details,
see commit:
63a1e1c95e ("arm64/cpufeature: don't use mutex in bringup path")
Today we have more users of cpus_have_const_cap() which are only called
once the relevant static keys are initialized, and it would be
beneficial to avoid the redundant code.
To that end, this patch adds a new cpus_have_final_cap(), helper which
is intend to be used in code which is only run once capabilities have
been finalized, and will never check the cpus_hwcap array. This helps
the compiler to generate better code as it no longer needs to generate
code to address and test the cpus_hwcap array. To help catch misuse,
cpus_have_final_cap() will BUG() if called before capabilities are
finalized.
In hyp context, BUG() will result in a hyp panic, but the specific BUG()
instance will not be identified in the usual way.
Comments are added to the various cpus_have_*_cap() helpers to describe
the constraints on when they can be used. For clarity cpus_have_cap() is
moved above the other helpers. Similarly the helpers are updated to use
system_capabilities_finalized() consistently, and this is made
__always_inline as required by its new callers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Pull networking fixes from David Miller:
"It looks like a decent sized set of fixes, but a lot of these are one
liner off-by-one and similar type changes:
1) Fix netlink header pointer to calcular bad attribute offset
reported to user. From Pablo Neira Ayuso.
2) Don't double clear PHY interrupts when ->did_interrupt is set,
from Heiner Kallweit.
3) Add missing validation of various (devlink, nl802154, fib, etc.)
attributes, from Jakub Kicinski.
4) Missing *pos increments in various netfilter seq_next ops, from
Vasily Averin.
5) Missing break in of_mdiobus_register() loop, from Dajun Jin.
6) Don't double bump tx_dropped in veth driver, from Jiang Lidong.
7) Work around FMAN erratum A050385, from Madalin Bucur.
8) Make sure ARP header is pulled early enough in bonding driver,
from Eric Dumazet.
9) Do a cond_resched() during multicast processing of ipvlan and
macvlan, from Mahesh Bandewar.
10) Don't attach cgroups to unrelated sockets when in interrupt
context, from Shakeel Butt.
11) Fix tpacket ring state management when encountering unknown GSO
types. From Willem de Bruijn.
12) Fix MDIO bus PHY resume by checking mdio_bus_phy_may_suspend()
only in the suspend context. From Heiner Kallweit"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (112 commits)
net: systemport: fix index check to avoid an array out of bounds access
tc-testing: add ETS scheduler to tdc build configuration
net: phy: fix MDIO bus PM PHY resuming
net: hns3: clear port base VLAN when unload PF
net: hns3: fix RMW issue for VLAN filter switch
net: hns3: fix VF VLAN table entries inconsistent issue
net: hns3: fix "tc qdisc del" failed issue
taprio: Fix sending packets without dequeueing them
net: mvmdio: avoid error message for optional IRQ
net: dsa: mv88e6xxx: Add missing mask of ATU occupancy register
net: memcg: fix lockdep splat in inet_csk_accept()
s390/qeth: implement smarter resizing of the RX buffer pool
s390/qeth: refactor buffer pool code
s390/qeth: use page pointers to manage RX buffer pool
seg6: fix SRv6 L2 tunnels to use IANA-assigned protocol number
net: dsa: Don't instantiate phylink for CPU/DSA ports unless needed
net/packet: tpacket_rcv: do not increment ring index on drop
sxgbe: Fix off by one in samsung driver strncpy size arg
net: caif: Add lockdep expression to RCU traversal primitive
MAINTAINERS: remove Sathya Perla as Emulex NIC maintainer
...
Add thermal zone and tmu node to support i.MX8MM thermal
driver, ONLY cpu thermal zone is supported, and cpu cooling
is also added.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add endpoint mode support for PCIe C5 controller in P2972-0000 platform
with information about supplies, PHY, PERST GPIO and GPIO that controls
PCIe reference clock coming from the host system.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Adding this alias for the Ethernet interface on Jetson TX1 allows the
bootloader to pass the MAC address to the Linux kernel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The following warning is observed on Jetson TX1 platform because the
supply regulator is not specified for the backlight.
WARNING KERN lp855x 0-002c: 0-002c supply power not found, using dummy regulator
The backlight supply is provided by the 3.3V SYS rail and so add this
as the supply for the backlight.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The following warning is observed on the Jetson TX2 platform ...
WARNING KERN tegra-sor 15540000.sor: 15540000.sor supply \
vdd-hdmi-dp-pll not found, using dummy regulator
The problem is caused because the regulator for the SOR device is
missing the '-supply' suffix in Device-Tree. Therefore, add the
'-supply' suffix to fix this warning.
Fixes: 3fdfaf8718 ("arm64: tegra: Enable DP support on Jetson TX2")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The following warning is observed on Jetson TX1, Jetson Nano and Jetson
TX2 platforms because the supply regulators are not specified for the
EEPROMs.
WARNING KERN at24 0-0050: 0-0050 supply vcc not found, using dummy regulator
WARNING KERN at24 0-0057: 0-0057 supply vcc not found, using dummy regulator
For both of these platforms the EEPROM is powered by the main 1.8V
supply rail and so populate the supply for these devices to fix these
warnings.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit a5b6b67364 ("arm64: tegra: Add ID EEPROM for Jetson TX1
module") populated the EEPROM on the Jetson TX1 module, but did not
enable the corresponding I2C controller. Enable the I2C controller so
that this EEPROM can be accessed.
Fixes: a5b6b67364 ("arm64: tegra: Add ID EEPROM for Jetson TX1 module")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
clk_out_2 is a clock provided by the PMC, rather than the clock and
reset controller, as previously erroneously defined.
This patch changes clk_out_2 provider to PMC and uses corresponding
PMC clock ID for clk_out_2.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra132 and Tegra210 PMC blocks have clk_out_1, clk_out_2, clk_out_3,
and a blink clock as a part of the PMC.
These clocks were erroneously provided by the clock and reset controller
and are now provided by the PMC instead because that's where the primary
controls are.
Clock IDs for these clocks are defined in the PMC dt-bindings.
This patch updates the device tree to include the PMC dt-bindings header
and adds the #clock-cells property with one clock specifier to the PMC
node.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add usb-role-switch entry to peripheral USB port and add corresponding
connector details.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra186 has one XUSB device mode controller, which can be operated in
HS and SS modes. Add DT entry for XUSB device mode controller.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 has one XUSB device mode controller, which can be operated in
HS and SS modes. Add DT entry for XUSB device mode controller.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add usb-role-switch entry to OTG USB port and add corresponding
connector details.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Populate OTG vbus regulator and add usb-role-switch entry to USB 2-0
port and corresponding connector details.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit enables XUSB host and pad controller in Tegra194
P2972-0000 board.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If the kernel configuration option CONFIG_PCIE_DW_PLAT_HOST is enabled
then this can cause the kernel to incorrectly probe the generic
designware PCIe platform driver instead of the Tegra194 designware PCIe
driver. This causes a boot failure on Tegra194 because the necessary
configuration to access the hardware is not performed.
The order in which the compatible strings are populated in Device-Tree
is not relevant in this case, because the kernel will attempt to probe
the device as soon as a driver is loaded and if the generic designware
PCIe driver is loaded first, then this driver will be probed first.
Therefore, to fix this problem, remove the "snps,dw-pcie" string from
the compatible string as we never want this driver to be probe on
Tegra194.
Fixes: 2602c32f15 ("arm64: tegra: Add P2U and PCIe controller nodes to Tegra194 DT")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The HiHope RZ/G2M is advertised as compatible with panel idk-1110wr
from Advantech, however the panel isn't sold alongside the board.
A new dts, adding everything that's required to get the panel to
work with HiHope RZ/G2M, is the most convenient way to support the
HiHope RZ/G2M when it's connected to the idk-1110wr.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/1583957020-16359-3-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add initial support for the Renesas M3ULCB board equipped with an R-Car
M3-W+ SiP with 8 (2 x 4) GiB of RAM.
To avoid build error on 'ulcb.dtsi', ssi2 is added into 'r8a77961.dtsi'.
Based on commit 92980759c1 ("arm64: dts: renesas: Add support for
Salvator-XS with R-Car M3-W+").
Signed-off-by: Yuya Hamamachi <yuya.hamamachi.sx@renesas.com>
Link: https://lore.kernel.org/r/20200309064425.25437-3-yuya.hamamachi.sx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a device node for the Thermal Sensor/Chip Internal Voltage Monitor
in the R-Car M3-W+ (R8A77961) SoC, and describe the thermal zones.
According to the R-Car Gen3 Hardware Manual Errata for Revision 2.00 of
Jan 31, 2020, the thermal parameters for R-Car M3-W+ are the same as for
R-Car M3-W.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200306110025.24747-1-geert+renesas@glider.be
The LS1028A has six LPUART controllers. Add the nodes.
This was tested on a custom board.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200307091302.14881-2-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the redundant _mem suffix for SDHC reg names.
For SDcard instance, no need supply reg names since hc reg map
is accessed with index. So remove reg names for SDcard.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1583946863-24308-2-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Enabling CQE support for eMMC by supplying the correct reg name
and flag which indicates CQE support.
Also remove the redundant _mem suffix for reg names.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/1583946863-24308-1-git-send-email-vbadigan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Register range of display clocks is 0x10000, as it can be seen from
DE2 documentation.
Fix it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Fixes: 2c796fc8f5 ("arm64: dts: allwinner: a64: add necessary device tree nodes for DE2 CCU")
[wens@csie.org: added fixes tag]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Currently, the EL0 SP alignment handler masks IRQs unnecessarily. It
does so due to historic code sharing of the EL0 SP and PC alignment
handlers, and branch predictor hardening applicable to the EL0 SP
handler.
We began masking IRQs in the EL0 SP alignment handler in commit:
5dfc6ed277 ("arm64: entry: Apply BP hardening for high-priority synchronous exception")
... as this shared code with the EL0 PC alignment handler, and branch
predictor hardening made it necessary to disable IRQs for early parts of
the EL0 PC alignment handler. It was not necessary to mask IRQs during
EL0 SP alignment exceptions, but it was not considered harmful to do so.
This masking was carried forward into C code in commit:
582f95835a ("arm64: entry: convert el0_sync to C")
... where the SP/PC cases were split into separate handlers, and the
masking duplicated.
Subsequently the EL0 PC alignment handler was refactored to perform
branch predictor hardening before unmasking IRQs, in commit:
bfe298745a ("arm64: entry-common: don't touch daif before bp-hardening")
... but the redundant masking of IRQs was not removed from the EL0 SP
alignment handler.
Let's do so now, and make it interruptible as with most other
synchronous exception handlers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
When building allnoconfig:
arch/arm64/kernel/cpu_errata.c:174:13: warning: unused function
'call_smc_arch_workaround_1' [-Wunused-function]
static void call_smc_arch_workaround_1(void)
^
1 warning generated.
Follow arch/arm and mark this function as __maybe_unused.
Fixes: 4db61fef16 ("arm64: kvm: Modernize __smccc_workaround_1_smc_start annotations")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Missing argument of another SYM_INNER_LABEL() breaks build for
CONFIG_FUNCTION_GRAPH_TRACER=y.
Fixes: e2d591d29d ("arm64: entry-ftrace.S: Convert to modern annotations for assembly functions")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Brown <broonie@kernel.org>
A test with the command below gives for example this error:
arch/arm64/boot/dts/rockchip/rk3399-evb.dt.yaml: amba: $nodename:0:
'amba' does not match
'^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
AMBA is a open standard for the connection and
management of functional blocks in a SoC.
It's compatible with 'simple-bus', so fix this error
by adding 'bus' to all Rockchip 'amba' nodes.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/
schemas/simple-bus.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200302153047.17101-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
i.MX8MQ Phanbell board uses Realtek RTL8211FD as Ethernet PHY.
Its datasheet states that the proper post reset duration should be at least 50 ms.
Fixes: f34d4bfab3 ("arm64: dts: imx8mq-phanbell: Add support for ethernet")
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull in downstream patch from NXP repository to enable fspi device.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
crypto child nodes should use the "jr" name (without an index),
as indicated in the DT binding.
Signed-off-by: Silvano di Ninno <silvano.dininno@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A test with the command below does not detect all errors
in combination with 'additionalProperties: false' and
allOf:
- $ref: "synopsys-dw-mshc-common.yaml#"
allOf:
- $ref: "mmc-controller.yaml#"
'additionalProperties' applies to all properties that are not
accounted-for by 'properties' or 'patternProperties' in
the immediate schema.
First when we combine rockchip-dw-mshc.yaml,
synopsys-dw-mshc-common.yaml and mmc-controller.yaml it gives
for example this error:
arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dt.yaml: mmc@fe320000:
'clock-freq-min-max' does not match any of the regexes:
'^.*@[0-9]+$', '^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|
uhs-(sdr(12|25|50|104)|ddr50))$', 'pinctrl-[0-9]+'
'clock-freq-min-max' is deprecated, so replace it by 'max-frequency'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200307134841.13803-5-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below does not detect all errors
in combination with 'additionalProperties: false' and
allOf:
- $ref: "synopsys-dw-mshc-common.yaml#"
allOf:
- $ref: "mmc-controller.yaml#"
'additionalProperties' applies to all properties that are not
accounted-for by 'properties' or 'patternProperties' in
the immediate schema.
First when we combine rockchip-dw-mshc.yaml,
synopsys-dw-mshc-common.yaml and mmc-controller.yaml it gives
this error:
arch/arm64/boot/dts/rockchip/rk3399-puma-haikou.dt.yaml: mmc@fe320000:
'vqmmc' does not match any of the regexes:
'^.*@[0-9]+$', '^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|
uhs-(sdr(12|25|50|104)|ddr50))$', 'pinctrl-[0-9]+'
'vqmmc' is not a valid property name for mmc nodes.
Fix this error by renaming it to 'vqmmc-supply'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200307134841.13803-4-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below does not detect all errors
in combination with 'additionalProperties: false' and
allOf:
- $ref: "synopsys-dw-mshc-common.yaml#"
allOf:
- $ref: "mmc-controller.yaml#"
'additionalProperties' applies to all properties that are not
accounted-for by 'properties' or 'patternProperties' in
the immediate schema.
First when we combine rockchip-dw-mshc.yaml,
synopsys-dw-mshc-common.yaml and mmc-controller.yaml it gives
this error:
arch/arm64/boot/dts/rockchip/rk3368-px5-evb.dt.yaml: mmc@ff0c0000:
'no-emmc' does not match any of the regexes:
'^.*@[0-9]+$', '^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|
uhs-(sdr(12|25|50|104)|ddr50))$', 'pinctrl-[0-9]+'
'no-emmc' is not a valid property name for mmc nodes,
so remove it.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200307134841.13803-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
An experimental test with the command below without
additional properties in 'rockchip-vop.yaml' gives this error:
arch/arm64/boot/dts/rockchip/px30-evb.dt.yaml: vop@ff470000:
'power-domains', 'rockchip,grf'
do not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm64/boot/dts/rockchip/px30-evb.dt.yaml: vop@ff460000:
'power-domains', 'rockchip,grf'
do not match any of the regexes: 'pinctrl-[0-9]+'
'rockchip,grf' is not used by the Rockchip VOP driver,
so remove it from 'vop' nodes in 'px30.dtsi'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/display/
rockchip/rockchip-vop.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200309081600.3887-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below does not detect all errors
in combination with 'additionalProperties: false' and
allOf:
- $ref: "spi-controller.yaml#"
'additionalProperties' applies to all properties that are not
accounted-for by 'properties' or 'patternProperties' in
the immediate schema.
First when we combine spi-rockchip.yaml and
spi-controller.yaml it gives this error:
arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dt.yaml: spi@ff1d0000:
'max-freq' does not match any of the regexes:
'^.*@[0-9a-f]+$', '^slave$'
'max-freq' is not a valid property name for spi nodes,
so remove it.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/spi-rockchip.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200309125145.14455-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
lx2160a-qds has 2 micron "mt35xu512aba" flashes of size 64M each
connected on A0 and B1 i.e on CS0 and CS3. Since flashes are connected
on different buses, only one flash can be probed at a time.
Add fspi node properties aligned with LX2160A-RDB fspi properties.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update fspi node compatibles of LX2160A-RDB to "jedec,spi-nor" for
automatic detection of flash.
This also helps in fixing below warning:
spi-nor spi0.0: found mt35xu512aba, expected m25p80
spi-nor spi0.1: found mt35xu512aba, expected m25p80
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It was based on Google Source Code for Coral Edge TPU Mendel release:
https://coral.googlesource.com/linux-imx/
It was tested on Coral Dev Board using this command:
sudo stress --cpu 4 --timeout 3600
Signed-off-by: Vitor Massaru Iha <vitor@massaru.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the iommu-map property to the pci nodes so that the firmware
fixes it up with the required values thus enabling iommu for
devices connected over pci.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
