The ability to change the max_rx_aggregation frames is useful
in cases of IOP.
There exist some devices (latest mobile phones and some AP's)
that tend to not respect a BA sessions maximum size (in Kbps).
These devices won't respect the AMPDU size that was negotiated during
association (even though they do respect the maximal number of packets).
This violation is characterized by a valid number of packets in
a single AMPDU. Even so, the total size will exceed the size negotiated
during association.
Eventually, this will cause some undefined behavior, which in turn
causes the hw to drop packets, causing the throughput to plummet.
This patch will make the subframe limitation to be held by each station,
instead of being held only by hw.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Insert the u32 monitor flags variable in a new structure
that represents a monitor interface.
This will allow to add more configuration variables to
that structure which will happen in an upcoming change.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stop downgrading TDLS chandef when reaching the AP BW. The AP provides
the necessary regulatory protection in this case.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=153961, which
reported an infinite loop here.
Reported-by: Kamil Toman <kamil.toman@gmail.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on which method the driver implements, userspace could
call this (indirectly, by getting station info) before the driver
knows about the station, possibly causing it to misbehave.
Therefore, add a check for sta->uploaded which indicates that the
driver knows about the station.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the code only touches the MAC headers, the offsets to the
network/transport headers remain the same throughout this function.
Remove pointless pieces of code that try to 'preserve' them.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mesh HWMP module will be able to rely on the HW
RC algorithm if it exists, for path metric calculations.
This allows the metric calculation mechanism to calculate
a correct metric, based on PER and last TX rate both via
HW RC algorithm if it exists or via parameters collected
by the SW.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The variable is added to allow the driver an easy access to
it's own hw->priv when the op is invoked.
This fixes a crash in wlcore because it was relying on a
station pointer that wasn't initialized yet. It's the wrong
way to fix the crash, but it solves the problem for now and
it does make sense to have the hw pointer here.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
[rewrite commit message, fix indentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If QoS frame with EOSP (end of service period) subfield=1 sent by local
peer was not acked by remote peer, local peer did not end the MPSP. This
prevents local peer from going to DOZE state. And if the remote peer
goes away without closing connection, local peer continues AWAKE state
and wastes battery.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code currently assumes that buffered multicast PS frames don't have
a pending ACK frame for tx status reporting.
However, hostapd sends a broadcast deauth frame on teardown for which tx
status is requested. This can lead to the "Have pending ack frames"
warning on module reload.
Fix this by using ieee80211_free_txskb/ieee80211_purge_tx_queue.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers (e.g. wl18xx) expect that the last stage in the
de-initialization process will be stopping the beacons, similar to AP flow.
Update ieee80211_stop_mesh() flow accordingly.
As peers can be removed dynamically, this would not impact other drivers.
Tested also on Ralink RT3572 chipset.
Signed-off-by: Maital Hahn <maitalm@ti.com>
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The logic was inverted here, set the bit if frames are pending.
Fixes: ba8c3d6f16 ("mac80211: add an intermediate software queue implementation")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, mesh power management functionality works only with kernel
MPM. Because user space MPM did not report mesh peer AID to kernel,
the kernel could not identify the bit in TIM element. So this patch
adds mesh peer AID setting API.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Continuing the workaround implemented in commit 23665aaf91
("mac80211: Interoperability workaround for 80+80 and 160 MHz channels")
use the same code to parse the Wide Bandwidth Channel Switch element
by converting to VHT Operation element since the spec also just refers
to that for parsing semantics, particularly with the workaround.
While at it, remove some dead code - the IEEE80211_STA_DISABLE_40MHZ
flag can never be set at this point since it's checked earlier and the
wide_bw_chansw_ie pointer is set to NULL if it's set.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the following to support beacon report radio measurement
with the measurement mode field set to passive or active:
1. Propagate the required scan duration to the device
2. Report the scan start time (in terms of TSF)
3. Report each BSS's detection time (also in terms of TSF)
TSF times refer to the BSS that the interface that requested the
scan is connected to.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[changed ath9k/10k, at76c59x-usb, iwlegacy, wl1251 and wlcore to match
the new API]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon report radio measurement requires reporting observed BSSs
on the channels specified in the beacon request. If the measurement
mode is set to passive or active, it requires actually performing a
scan (passive or active, accordingly), and reporting the time that
the scan was started and the time each beacon/probe was received
(both in terms of TSF of the BSS of the requesting AP). If the
request mode is table, this information is optional.
In addition, the radio measurement request specifies the channel
dwell time for the measurement.
In order to use scan for beacon report when the mode is active or
passive, add a parameter to scan request that specifies the
channel dwell time, and add scan start time and beacon received time
to scan results information.
Supporting beacon report is required for Multi Band Operation (MBO).
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current implementation of handling ADDBA Request while a session
is already active with the peer is wrong - in case the peer is using
the existing session's dialog token this should be treated as update
to the session, which can update the timeout value.
We don't really have a good way of supporting that, so reject, but
implement the required behaviour in the spec of "Even if the updated
ADDBA Request frame is not accepted, the original Block ACK setup
remains active." (802.11-2012 10.5.4)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We've accumulated a couple of different fixes now to mesh_sta_cleanup()
due to the different paths that user_mpm and !user_mpm cases take -- one
fix to flush nexthop paths and one to fix the counting.
The only caller of mesh_plink_deactivate() is mesh_sta_cleanup(), so we
can push the user_mpm checks down into there in order to share more
code.
In doing so, we can remove an extra call to mesh_path_flush_by_nexthop()
and the (unnecessary) call to mesh_accept_plinks_update(). This will
also ensure the powersaving state code gets called in the user_mpm case.
The only cleanup tasks we need to avoid when MPM is in user-space
are sending the peering frames and stopping the plink timer, so wrap
those in the appropriate check.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Previously, the action frames to group address was not encrypted. But
[1] "Table 8-38 Category values" indicates "Mesh" and "Multihop" category
action frames should be encrypted (Group addressed privacy == yes). And the
encyption key should be MGTK ([1] 10.13 Group addressed robust management frame
procedures). So this patch modifies the code to make it suitable for spec.
[1] IEEE Std 802.11-2012
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
We normally return an uninitialized value, but no one checks it so it
doesn't matter. Anyway, let's silence the static checker warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
If a user space program (e.g., wpa_supplicant) deletes a STA entry that
is currently in NL80211_PLINK_ESTAB state, the number of established
plinks counter was not decremented and this could result in rejecting
new plink establishment before really hitting the real maximum plink
limit. For !user_mpm case, this decrementation is handled by
mesh_plink_deactive().
Fix this by decrementing estab_plinks on STA deletion
(mesh_sta_cleanup() gets called from there) so that the counter has a
correct value and the Beacon frame advertisement in Mesh Configuration
element shows the proper value for capability to accept additional
peers.
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
* the biggest change is Michał's work on integrating FQ/codel
with the mac80211 internal software queues
* cfg80211 connect result gets clarified for the
"no connection at all" case
* advertisement of per-interface type capabilities, in case
they differ (which makes a lot of sense for some capabilities)
* most of the nl80211 & hwsim unprivileged namespace operation
changes
* human-readable VHT capabilities in debugfs
* some other cleanups, like spelling
-----BEGIN PGP SIGNATURE-----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=FvhQ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-06-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For the next cycle, we have the following:
* the biggest change is Michał's work on integrating FQ/codel
with the mac80211 internal software queues
* cfg80211 connect result gets clarified for the
"no connection at all" case
* advertisement of per-interface type capabilities, in case
they differ (which makes a lot of sense for some capabilities)
* most of the nl80211 & hwsim unprivileged namespace operation
changes
* human-readable VHT capabilities in debugfs
* some other cleanups, like spelling
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no other limit other than a global
packet count limit when using software queuing.
This means a single flow queue can grow insanely
long. This is particularly bad for TCP congestion
algorithms which requires a little more
sophisticated frame dropping scheme than a mere
headdrop on limit overflow.
Hence apply (a slighly modified, to fit the knobs)
CoDel5 on flow queues. This improves TCP
convergence and stability when combined with
wireless driver which keeps its own tx queue/fifo
at a minimum fill level for given link conditions.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds a debugfs entry to read and modify some fq parameters.
This makes it easy to debug, test and experiment.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[remove module parameter for now]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211's software queues were designed to work
very closely with device tx queues. They are
required to make use of 802.11 packet aggregation
easily and efficiently.
Due to the way 802.11 aggregation is designed it
only makes sense to keep fair queuing as close to
hardware as possible to reduce induced latency and
inertia and provide the best flow responsiveness.
This change doesn't translate directly to
immediate and significant gains. End result
depends on driver's induced latency. Best results
can be achieved if driver keeps its own tx
queue/fifo fill level to a minimum.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Qdiscs are designed with no regard to 802.11
aggregation requirements and hand out
packet-by-packet with no guarantee they are
destined to the same tid. This does more bad than
good no matter how fairly a given qdisc may behave
on an ethernet interface.
Software queuing used per-AC netdev subqueue
congestion control whenever a global AC limit was
hit. This meant in practice a single station or
tid queue could starve others rather easily. This
could resonate with qdiscs in a bad way or could
just end up with poor aggregation performance.
Increasing the AC limit would increase induced
latency which is also bad.
Disabling qdiscs by default and performing
taildrop instead of netdev subqueue congestion
control on the other hand makes it possible for
tid queues to fill up "in the meantime" while
preventing stations starving each other.
This increases aggregation opportunities and
should allow software queuing based drivers
achieve better performance by utilizing airtime
more efficiently with big aggregates.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes it a lot easier to understand the capabilities used
by the station:
VHT supported
cap: 0x300819b2
MAX-MPDU-11454
80Mhz
RXLDPC
SHORT-GI-80
TXSTBC
RXSTBC_1
SU-BEAMFORMER-CAPABLE
SU-BEAMFORMEE-CAPABLE
BEAMFORMEE-STS: 0x0
SOUNDING-DIMENSIONS: 0x0
MU-BEAMFORMER-CAPABLE
MPDU-LENGTH-EXPONENT: 0x0
LINK-ADAPTATION-VHT-MRQ-MFB: 0x0
RX-ANTENNA-PATTERN
TX-ANTENNA-PATTERN
RX MCS: fffe
TX MCS: fffe
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The header field is defined as u8[] but also accessed as struct
ieee80211_hdr. Enforce an alignment of 2 to prevent unnecessary
unaligned accesses, which can be very harmful for performance on many
platforms.
Fixes: e495c24731 ("mac80211: extend fast-xmit for more ciphers")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* completion and fixups of nla_put_64_64bit() work
* remove a/b/g/n from wext nickname to avoid confusion
with 11ac (which wouldn't even fit fully there due to
string length restrictions)
along with some other minor changes/cleanups.
-----BEGIN PGP SIGNATURE-----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=QNxF
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-05-12' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some more work for 4.7, notably:
* completion and fixups of nla_put_64_64bit() work
* remove a/b/g/n from wext nickname to avoid confusion
with 11ac (which wouldn't even fit fully there due to
string length restrictions)
along with some other minor changes/cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When using RSS, frames might not be processed in the correct order,
and thus AP_LINK_PS must be used; most likely with firmware keeping
track of the powersave state, this is the case in iwlwifi now.
In this case, the driver can use ieee80211_sta_ps_transition() to
still have mac80211 manage powersave buffering. However, for U-APSD
and PS-Poll this isn't sufficient. If the device can't manage that
entirely on its own, mac80211's code should be used.
To allow this, export two functions: ieee80211_sta_uapsd_trigger()
and ieee80211_sta_pspoll().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some hardware (iwlwifi an example) de-aggregate AMSDUs and copy the IV
as is to the generated MPDUs, so the same PN appears in multiple
packets without being a replay attack. Allow driver to explicitly
indicate that a frame is allowed to have the same PN as the previous
frame.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, after a sudden AP disappearing and reconnection to
another AP in the same ESS, user space gets the old AP in scan
results (cached). User space may decide to roam to that old AP
which will cause a disconnection and longer recovery.
Remove APs that are probably out of range from BSS table.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case that dev_alloc_name() fails, e.g. because the name was
given by the user and already exists, we need to clean up properly
and free the per-CPU statistics. Fix that.
Cc: stable@vger.kernel.org
Fixes: 5a490510ba ("mac80211: use per-CPU TX/RX statistics")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fixes:
net/mac80211/mesh_hwmp.c:603:26: warning: ‘target_metric’ may be used uninitialized in this function
target_metric is only consumed when reply = true so no bug exists here,
but not all versions of gcc realize it. Initialize to 0 to remove the
warning.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Prevents excessive A-MSDU aggregation at low data rates or bad
conditions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Requires software tx queueing and fast-xmit support. For good
performance, drivers need frag_list support as well. This avoids the
need for copying data of aggregated frames. Running without it is only
supported for debugging purposes.
To avoid performance and packet size issues, the rate control module or
driver needs to limit the maximum A-MSDU size by setting
max_rc_amsdu_len in struct ieee80211_sta.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[fix locking issue]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver advertises the new HW flag USE_RSS, make the
station statistics on the fast-rx path per-CPU. This will
enable calling the RX in parallel, only hitting locking or
shared cachelines when the fast-RX path isn't available.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The regular RX path has a lot of code, but with a few
assumptions on the hardware it's possible to reduce the
amount of code significantly. Currently the assumptions
on the driver are the following:
* hardware/driver reordering buffer (if supporting aggregation)
* hardware/driver decryption & PN checking (if using encryption)
* hardware/driver did de-duplication
* hardware/driver did A-MSDU deaggregation
* AP_LINK_PS is used (in AP mode)
* no client powersave handling in mac80211 (in client mode)
of which some are actually checked per packet:
* de-duplication
* PN checking
* decryption
and additionally packets must
* not be A-MSDU (have been deaggregated by driver/device)
* be data packets
* not be fragmented
* be unicast
* have RFC 1042 header
Additionally dynamically we assume:
* no encryption or CCMP/GCMP, TKIP/WEP/other not allowed
* station must be authorized
* 4-addr format not enabled
Some data needed for the RX path is cached in a new per-station
"fast_rx" structure, so that we only need to look at this and
the packet, no other memory when processing packets on the fast
RX path.
After doing the above per-packet checks, the data path collapses
down to a pretty simple conversion function taking advantage of
the data cached in the small fast_rx struct.
This should speed up the RX processing, and will make it easier
to reason about parallelizing RX (for which statistics will need
to be per-CPU still.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On 32-bit platforms, the 64-bit counters we keep need to be protected
to be consistently read. Use the u64_stats_sync mechanism to do that.
In order to not end up with overly long lines, refactor the tidstats
assignments a bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When storing the last_rate_* values in the RX code, there's nothing
to guarantee consistency, so a concurrent reader could see, e.g.
last_rate_idx on the new value, but last_rate_flag still on the old,
getting completely bogus values in the end.
To fix this, I lifted the sta_stats_encode_rate() function from my
old rate statistics code, which encodes the entire rate data into a
single 16-bit value, avoiding the consistency issue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of touching the rx_stats.last_rx from the status path, introduce
and use a status_stats.last_ack variable. This will make rx_stats.last_rx
indicate when the last frame was received, making it available for real
"last_rx" and statistics gathering; statistics, when done per-CPU, will
need to figure out which place was updated last for those items where the
"last" value is exposed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to update rx_stats.last_rx after allocating
a station since it's already updated during allocation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the averaged values out of rx_stats and into rx_stats_avg,
to cleanly split them out. The averaged ones cannot be supported
for parallel RX in a per-CPU fashion, while the other values can
be collected per CPU and then combined/selected when needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the semicolon, people typically assume that and
once line already put a semicolon behind the "call".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For the RX MSDU statistics, we need to count the number of
MSDUs created and accepted from an A-MSDU. Right now, all
frames in any A-MSDUs were completely ignored. Fix this by
moving the RX MSDU statistics accounting into the deliver
function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes drivers already looked up, or know out-of-band
from their device, which station transmitted a given RX
frame. Allow them to pass the station pointer to mac80211
to save the extra lookup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Lockdep warned of a lock dependency between the mesh_plink lock
and the internal lock for the rhashtable. The problem is that
the rhashtable code uses a spin lock with softirqs enabled, while
mesh_plink_timer executes a walk (to flush paths on a state change)
inside a softirq with the plink lock held.
This leads to the following deadlock if the timer fires while rht
lock is held on this CPU, and plink lock is held on another CPU:
CPU0 CPU1
---- ----
lock(&(&ht->lock)->rlock);
local_irq_disable();
lock(&(&sta->mesh->plink_lock)->rlock);
lock(&(&ht->lock)->rlock);
<Interrupt>
lock(&(&sta->mesh->plink_lock)->rlock);
*** DEADLOCK ***
Fix by waiting until we drop the plink lock to flush paths.
Fixes: d48a1b7cd439 ("mac80211: mesh: convert path table to rhashtable")
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Several of the mesh path fields are undocumented and some
of the documentation is no longer correct or relevant after
the switch to rhashtable. Clean up the kernel doc
accordingly and reorder some fields to match the structure
layout.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reduce padding waste in struct mesh_table and struct rmc_entry by
moving the smaller fields to the end.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we have converted the mesh path tables to rhashtable, we are
no longer swapping out the entire mesh_pathtbl pointer with RCU.
As a result, we no longer need indirection to the hlist head for
the gates list and can simply embed it, saving a pair of
pointer-sized allocations.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The RMC cache has 256 list heads plus a u32, which puts it at the
unfortunate size of 4104 bytes with padding. kmalloc() will then
round this up to the next power-of-two, so we wind up actually
using two pages here where most of the second is wasted.
Switch to hlist heads here to reduce the structure size down to
fit within a page.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the unlikely case that mesh_rmc_init() fails with -ENOMEM,
the rmc pointer will be left as NULL but the interface is still
operational because ieee80211_mesh_init_sdata() is not allowed
to fail.
If this happens, we would blindly dereference rmc when checking
whether a multicast frame is in the cache. Instead just drop the
frames in the forwarding path.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Legacy clients don't support P2P power save mechanism, and thus if a P2P GO
has a legacy client connected to it, it should disable P2P PS mechanisms.
Let the driver know about this with a new bss_conf parameter.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the likely case that probe_count is 0, don't write to the
memory there.
Also use ifmgd consistently in the function, instead of using
sdata->u.mgd as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code is only used with iwlwifi, but still should have proper
mac80211 naming scheme; fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Avoid the really strange %s%s%s expression, use an array
of flag names and check that all flags are present.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the device implements dynamic PS itself, there's no need
to ever start the dynamic powersave timer on RX.
While at it, fix up some indentation in this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the previous patch, the struct only has a single member,
so remove the struct and leave just the single member.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove unused variable in per STA debugfs structure, 'commit 34e895075e
("mac80211: allow station add/remove to sleep")' removed the only user of
'add_has_run'.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the debugfs entry for starting aggregation session
starts it with timeout of 5 seconds. Allow opening a session
with a custom timeout (according to spec 0 is no timeout).
while at it, refactor the function and remove the magic numbers.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
NETIF_F_RXCSUM is not in the white list, though some
drivers may want to set it in order to enable seeing the
actual RX checksum status in ethtool.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow publishing RRM capabilities for features that are not
HW dependent.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There were a few issues that were slowing down the process of finding
the optimal rate, especially on devices with multi-rate retry
limitations:
When max_tp_rate[0] was slower than max_tp_rate[1], the code did not
sample max_tp_rate[1], which would often allow it to switch places with
max_tp_rate[0] (e.g. if only the first sampling attempts were bad, but the
rate is otherwise good).
Also, sample attempts of rates between max_tp_rate[0] and [1] were being
ignored in this case, because the code only checked if the rate was
slower than [1].
Fix this by checking against the fastest / second fastest max_tp_rate
instead of assuming a specific order between the two.
In my tests this patch significantly reduces the time until minstrel_ht
finds the optimal rate right after assoc
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we enqueued the frame that was supposed to be sent
during the SP, and that frame may very well cary the
IEEE80211_TX_STATUS_EOSP bit, we may never close the SP
(WLAN_STA_SP will never be cleared). If that happens, we
will not open any new SP and will never respond to any poll
frame from the client.
Clear WLAN_STA_SP manually if a frame that was polled during
the SP is queued because of a starting A-MPDU session. The
client may not see the EOSP bit, but it will at least be
able to poll new frames in another SP.
Reported-by: Alesya Shapira <alesya.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[remove erroneous comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is possible that the station is connected to an AP
with bandwidth of 80+80MHz or 160MHz. In such cases
there is no need to perform an upgrade as the maximal
supported bandwidth is 80MHz.
In addition, when upgrading and setting center_freq1
and bandwidth to 80MHz also set center_freq2 to 0.
Fixes: 0fabfaafec ("mac80211: upgrade BW of TDLS peers when possible"
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Frames that are sent between
ampdu_action(IEEE80211_AMPDU_TX_START) and the move to the
HT_AGG_STATE_OPERATIONAL state are buffered.
If we try to start an A-MPDU session while the peer is
sleeping and polling frames with U-APSD, we may have frames
that will be buffered by ieee80211_tx_prep_agg. These frames
have IEEE80211_TX_CTL_NO_PS_BUFFER set since they are sent to
a sleeping client and possibly IEEE80211_TX_STATUS_EOSP.
If the frame is buffered, we need clear these two flags
since they will be re-sent after the move to
HT_AGG_STATE_OPERATIONAL state which is very likely to
happen after the SP ends.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 976bd9efda ("mac80211: move beacon_loss_count into ifmgd")
removed the member from the sta_info struct but the description stayed
lingering. Remove it.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By default, the rhashtable logic will fail to insert
objects if the key-chains are too long and un-balanced.
In the degenerate case where mac80211 is creating many
virtual interfaces connected to the same peer(s), this
case can happen.
St insecure_elasticity to true to allow chains to grow
as long as needed.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[remove message, change commit message slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The original hand-implemented hash-table in mac80211 couldn't result
in insertion errors, and while converting to rhashtable I evidently
forgot to check the errors.
This surfaced now only because Ben is adding many identical keys and
that resulted in hidden insertion errors.
Cc: stable@vger.kernel.org
Fixes: 7bedd0cfad ("mac80211: use rhashtable for station table")
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fall back to rate control if the requested bitrate was not found.
Fixes: dfdfc2beb0 ("mac80211: Parse legacy and HT rate in injected frames")
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The MCS bandwidth part of the radiotap header is 2 bits wide. The full 2
bit have to compared against IEEE80211_RADIOTAP_MCS_BW_40 and not only if
the first bit is set. Otherwise IEEE80211_RADIOTAP_MCS_BW_40 can be
confused with IEEE80211_RADIOTAP_MCS_BW_20U.
Fixes: dfdfc2beb0 ("mac80211: Parse legacy and HT rate in injected frames")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices, like iwlwifi, have RSS queues. This may cause a
situation where a disassociation is handled in control path and
results in station removal while there are prior RX frames
that were still not processed in other queues. When they will
be processed the station will be gone, and the frames will be
dropped.
Add a synchronization interface to avoid that. When driver returns
from the synchronization mac80211 may remove the station.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the time since the mesh path table was implemented as an
RCU-traversable, dynamically growing hash table, a generic RCU
hashtable implementation was added to the kernel.
Switch the mesh path table over to rhashtable to remove some code
and also gain some features like automatic shrinking.
Cc: Thomas Graf <tgraf@suug.ch>
Cc: netdev@vger.kernel.org
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh path table uses a struct mesh_node in its hlists in
order to support a resizable hash table: the mesh_node provides
an indirection to the actual mesh path so that two different
bucket lists can point to the same path entry.
However, for the known gates list, we don't need this indirection
because there is ever only one list. So we can just embed the
hlist_node in the mesh path itself, which simplifies things a bit
and saves a linear search whenever we need to find an item in
the list.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove duplicate code to allocate and initialize a mesh
path or mesh proxy path.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that the sdata pointer is the same for all entries of a
path table, hashing it is pointless, so hash only the address.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh path and mesh gate hashtables are global, containing
all of the mpaths for every mesh interface, but the paths are
all tied logically to a single interface. The common case is
just a single mesh interface, so optimize for that by moving
the global hashtable into the per-interface struct.
Doing so allows us to drop sdata pointer comparisons inside
the lookups and also saves a few bytes of BSS and data.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the cfg80211 scan trigger operation specifies a single BSSID, use
that value instead of the wildcard BSSID in the Probe Request frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The min_def chanctx is affected not only by the current chandef, but
sometimes also by other stations on the vif. There's a valid scenario
where a TDLS peer can widen its BW, thereby causing the min_def
to increase.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The previous approach simply ignored chandef restrictions when calculating
the appropriate peer BW for a WIDER_BW peer. This could result in a
regulatory violation if both peers indicated 80MHz support, but the
regdomain forbade it.
Change the approach to setting a WIDER_BW peer's BW. Don't exempt it from
the chandef width at first. If during TDLS negotiation the chandef width
is upgraded, update the peer's BW to match.
Fixes: 0fabfaafec ("mac80211: upgrade BW of TDLS peers when possible")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even if the current chandef width is equal to the station's max-BW, it
doesn't mean it's a valid width for TDLS. Make sure to always check
regulatory constraints in these cases.
Fixes: 0fabfaafec ("mac80211: upgrade BW of TDLS peers when possible")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Buffered multicast frames must be passed to the driver directly via
drv_tx instead of going through the txq, otherwise they cannot easily be
scheduled to be sent after DTIM.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When HW crypto is used, there's no need for the CCMP/GCMP MIC to
be available to mac80211, and the hardware might have removed it
already after checking. The MIC is also useless to have when the
frame is already decrypted, so allow indicating that it's not
present.
Since we are running out of bits in mac80211_rx_flags, make
the flags field a u64.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was requested by Android, and the appropriate cfg80211 API
had been added by Dmitry. Support it in mac80211, allowing drivers
to provide the timestamp.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add VHT radiotap parsing support to ieee80211_parse_tx_radiotap().
That capability has been tested using a d-link dir-860l rev b1 running
OpenWrt trunk and mt76 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* check GCMP encryption vs. fragmentation properly; we'd found
this problem quite a while ago but waited for the 802.11 spec
to be updated
* fix RTS/CTS logic in minstrel_ht
* fix RX of certain public action frames in AP mode
* add mac80211_hwsim to MAC80211 in MAINTAINERS, this helps
the kbuild robot pick up the right tree for it
-----BEGIN PGP SIGNATURE-----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=2rZC
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-03-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here are a few more fixes for the current cycle:
* check GCMP encryption vs. fragmentation properly; we'd found
this problem quite a while ago but waited for the 802.11 spec
to be updated
* fix RTS/CTS logic in minstrel_ht
* fix RX of certain public action frames in AP mode
* add mac80211_hwsim to MAC80211 in MAINTAINERS, this helps
the kbuild robot pick up the right tree for it
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
RTS/CTS needs to be enabled if the rate is a fallback rate *or* if it's
a dual-stream rate and the sta is in dynamic SMPS mode.
Cc: stable@vger.kernel.org
Fixes: a3ebb4e1b7 ("mac80211: minstrel_ht: handle peers in dynamic SMPS")
Reported-by: Matías Richart <mrichart@fing.edu.uy>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Public Action frames use special rules for how the BSSID field (Address
3) is set. A wildcard BSSID is used in cases where the transmitter and
recipient are not members of the same BSS. As such, we need to accept
Public Action frames with wildcard BSSID.
Commit db8e173245 ("mac80211: ignore frames between TDLS peers when
operating as AP") added a rule that drops Action frames to TDLS-peers
based on an Action frame having different DA (Address 1) and BSSID
(Address 3) values. This is not correct since it misses the possibility
of BSSID being a wildcard BSSID in which case the Address 1 would not
necessarily match.
Fix this by allowing mac80211 to accept wildcard BSSID in an Action
frame when in AP mode.
Fixes: db8e173245 ("mac80211: ignore frames between TDLS peers when operating as AP")
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Just like for CCMP we need to check that for GCMP the fragments
have PNs that increment by one; the spec was updated to fix this
security issue and now has the following text:
The receiver shall discard MSDUs and MMPDUs whose constituent
MPDU PN values are not incrementing in steps of 1.
Adapt the code for CCMP to work for GCMP as well, luckily the
relevant fields already alias each other so no code duplication
is needed (just check the aliasing with BUILD_BUG_ON.)
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* stop critical protocol session on disconnect to avoid
it getting stuck
* wext: fix two RTNL message ordering issues
* fix an uninitialized value (found by KASAN)
* fix an out-of-bounds access (also found by KASAN)
* clear connection keys when freeing them in all cases
(IBSS, all other places already did so)
* fix expected throughput unit to get consistent values
* set default TX aggregation timeout to 0 in minstrel
to avoid (really just hide) issues and perform better
-----BEGIN PGP SIGNATURE-----
iQIcBAABCgAGBQJWzCthAAoJEGt7eEactAAdLjEP/38ujypJkVlwZzm9L8MbSVPk
qPMmRBshVX89xOXtwJLJHOGCRY6/pfe1LKThodOp+hj+NH7OLLuAGFDScjr7eEjG
bAQrXZ8dDIo54uri4EF4jBfkqUsePs+d4VpLgdJ2Gdh2UgIdDlUcggiEyOSicc27
ZP3gRQzad8tP0O+MuqiAjwJE4C3AUzzj+8TXJJXjrT3RvDpvZfA3MClfiQVhRM+4
3qtFhqFFGfIjTSHCoGr+0RYhLJwfjalIyoENR/kYizjHXU4YtZcu7ihdixKmG3Qb
SUIlNl60WSyoh2+PXx3wp0gfTc0BrOVIpB+TQPouRu5D+tLRiPwlieVrlfJyIUJ5
ccU1RWoTZn+3OVSjNF+9IGbpL43cjaJpZUMU/mQES7+z+uEwlzdcnwDScG7sMMC+
KIyKZ4v+2sBPKYYKAzGxHb2lfTMyp9sCs25U30yqLX3RSNtuxJbDwuKrwbKa1CMx
WEjImI+iSApjTch0THAxV8/sO/ZneuRZP76PXmSDm7Mzf9qob8fnpCjFsHTypDpx
eWy8AHPhIhb3ni6Cm3TfsGLjGE4KGwD/lEwmAles2Cj48N4b2UwRjMrJ5GRxuV00
9kh2MvFEmSYBU4dw6LQmemjxNNIa792+JiS4AKJXBqkPK1H1YFvq7i8Hl9a1tQ0P
SDgbH5x6AYvmTRcD97Ph
=01n9
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-02-23' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Another small set of fixes:
* stop critical protocol session on disconnect to avoid
it getting stuck
* wext: fix two RTNL message ordering issues
* fix an uninitialized value (found by KASAN)
* fix an out-of-bounds access (also found by KASAN)
* clear connection keys when freeing them in all cases
(IBSS, all other places already did so)
* fix expected throughput unit to get consistent values
* set default TX aggregation timeout to 0 in minstrel
to avoid (really just hide) issues and perform better
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers may need to track which vif is using VHT MU-MIMO.
Move the flag indicationg the ownership of MU_MIMO to
ieee80211_vif.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Provide an interface to the lower level driver to set the VHT
MU-MIMO data. This is needed for example when there is an update
of the group data during low power state, where the management
frame will not be passed to the host at all.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the PNs of all the tx keys are now tracked in the public
part of the key struct (with atomic counter), we no longer
need these functions.
dvm and vt665{5,6} are currently the only users of these functions,
so update them accordingly.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers/devices might want to set the IVs by
themselves (and still let mac80211 generate MMIC).
Specifically, this is needed when the device does
offloading at certain times, and the driver has
to make sure that the IVs of new tx frames (from
the host) are synchronized with IVs that were
potentially used during the offloading.
Similarly to CCMP, move the TX IVs of TKIP keys to the
public part of the key struct, and export a function
to add the IV right into the crypto header.
The public tx_pn field is defined as atomic64, so define
TKIP_PN_TO_IV16/32 helper macros to convert it to iv16/32
when needed.
Since the iv32 used for the p1k cache is taken
directly from the frame, we can safely remove
iv16/32 from being protected by tkip.txlock.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix wiphy supported_band access in tx radiotap parsing introduced
in commit 5ec3aed9ba4c ("mac80211: Parse legacy and HT rate in
injected frames"). In particular, info->band is always set to 0
(IEEE80211_BAND_2GHZ) since it has not assigned yet.
This cause a kernel crash on 5GHz only devices.
Move ieee80211_parse_tx_radiotap() after info->band assignment
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The source and destintation addresses in the memcpy arguments
are flipped. Fix that.
Fixes: 23a1f8d44c0b("mac80211: process and save VHT MU-MIMO group frame")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mpp_path_del() and mesh_path_del() are mostly the same function.
Move common code into a new static function.
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Henning Rogge <henning.rogge@fkie.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remember the last time when a mpp table entry is used for
rx or tx and remove them after MESH_PATH_EXPIRE time.
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Henning Rogge <henning.rogge@fkie.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the mesh_path_del() function remove all mpp table entries
that are proxied by the removed mesh path.
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Henning Rogge <henning.rogge@fkie.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Prepararation for zero-copy A-MSDU support with page fragment SKBs
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On error we jumped to the error label and returned the error code but we
missed releasing sinfo.
Fixes: 5fe74014172d ("mac80211: avoid excessive stack usage in sta_info")
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Number of deployed 80 MHz capable VHT stations that do not support 80+80
and 160 MHz bandwidths seem to misbehave when trying to connect to an AP
that advertises 80+80 or 160 MHz channel bandwidth in the VHT Operation
element. To avoid such issues with deployed devices, modify the design
based on recently accepted IEEE 802.11 standard changes (*).
This allows poorly implemented VHT 80 MHz stations to connect with the
AP in 80 MHz mode. 80+80 and 160 MHz capable stations need to support
the new workaround mechanism to allow full bandwidth to be used.
However, there are more or less no impacted station with 80+80/160
capability deployed.
The rebased version of this patch is based on the updated version from
Johannes Berg to take the HT/VHT chandef refactoring into account.
(*) Changes in
https://mentor.ieee.org/802.11/dcn/15/11-15-1530-04-000m-vht160-operation-signaling-through-non-zero-ccfs1.docx
were accepted during the IEEE 802.11 January 2016 meeting.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If any frames are dropped that are part of a BA session, the reorder
buffer will "indefinitely" (until the timeout) wait for them to come
in (or a BAR moving the window) and won't release frames after them.
This means it isn't possible to filter frames within a BA session in
firmware.
Introduce an API function that allows such filtering. Calling this
function will move the BA window forward to the new SSN, and allows
marking frames after the SSN as having been filtered, so any future
reordering activity will release frames while skipping the holes.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clean up ieee80211_rx_reorder_ready() callers by passing the RX
TID struct and the index, instead of the frames list. This will
make it more extensible as well.
While at it, move the inline to rx.c as it's only used there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will allow drivers to make more educated
decisions whether to defer transmission or not.
Relying on wake_tx_queue() call count implicitly
was not possible because it could be called
without queued frame count actually changing on
software tx aggregation start/stop code paths.
It was also not possible to know how long
byte-wise queue was without dequeueing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers/devices without their own rate control algorithm can get the
information what rates they should use from either the radiotap header of
injected frames or from the rate control algorithm. But the parsing of the
legacy rate information from the radiotap header was removed in commit
e6a9854b05 ("mac80211/drivers: rewrite the rate control API").
The removal of this feature heavily reduced the usefulness of frame
injection when wanting to simulate specific transmission behavior. Having
rate parsing together with MCS rates and retry support allows a fine
grained selection of the tx behavior of injected frames for these kind of
tests.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mean_chain_len field in struct mesh_table is copied whenever a
new mesh table is allocated, but only ever has the value 2 and is
never otherwise updated, so just remove it and use the related
define instead.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When CONFIG_OPTIMIZE_INLINING is set, the sta_info_insert_finish
function consumes more stack than normally, exceeding the
1024 byte limit on ARM:
net/mac80211/sta_info.c: In function 'sta_info_insert_finish':
net/mac80211/sta_info.c:561:1: error: the frame size of 1080 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
It turns out that there are two functions that put a 'struct station_info'
on the stack: __sta_info_destroy_part2 and sta_info_insert_finish, and
this structure alone requires up to 792 bytes.
Hoping that both are called rarely enough, this replaces the
on-stack structure with a dynamic allocation, which unfortunately
requires some suboptimal error handling for out-of-memory.
The __sta_info_destroy_part2 function is actually affected by the
stack usage twice because it calls cfg80211_del_sta_sinfo(), which
has another instance of struct station_info on its stack.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 98b6218388 ("mac80211/cfg80211: add station events")
Fixes: 6f7a8d26e2 ("mac80211: send statistics with delete station event")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make sure there's at least a debug message whenever the
connection to the AP is terminated.
Also change one message from wiphy_debug() to the common
mlme_dbg().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When joining IBSS a full scan should be initiated in order to search
for existing cell, unless the fixed_channel parameter was set.
A default channel to create the IBSS on if no cell was found is
provided as well.
However - a scan is initiated only on the default channel provided
regardless of whether ifibss->fixed_channel is set or not, with the
obvious result of the cell not joining existing IBSS cell that is
on another channel.
Fixes: 76bed0f43b ("mac80211: IBSS fix scan request")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The timestamp given by iwlwifi is at the beginning of the
frame over the air, at (or during) the SYNC field. Allow
such timestamps to be given to mac80211, at least (for now)
for frames with non-HT/VHT preambles.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ieee80211_queue_stopped() expects hw queue
number but it was given raw WMM AC number instead.
This could cause frame drops and problems with
traffic in some cases - most notably if driver
doesn't map AC numbers to queue numbers 1:1 and
uses ieee80211_stop_queues() and
ieee80211_wake_queue() only without ever calling
ieee80211_wake_queues().
On ath10k it was possible to hit this problem in
the following case:
1. wlan0 uses queue 0
(ath10k maps queues per vif)
2. offchannel uses queue 15
3. queues 1-14 are unused
4. ieee80211_stop_queues()
5. ieee80211_wake_queue(q=0)
6. ieee80211_wake_queue(q=15)
(other queues are not woken up because both
driver and mac80211 know other queues are
unused)
7. ieee80211_rx_h_mesh_fwding()
8. ieee80211_select_queue_80211() returns 2
9. ieee80211_queue_stopped(q=2) returns true
10. frame is dropped (oops!)
Fixes: d3c1597b8d ("mac80211: fix forwarded mesh frame queue mapping")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver can access the queue simultanously
while mac80211 tears down the interface. Without
spinlock protection this could lead to corrupting
sk_buff_head and subsequently to an invalid
pointer dereference.
Fixes: ba8c3d6f16 ("mac80211: add an intermediate software queue implementation")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove unnecessory "if" statement and club it with previos "if" block.
Signed-off-by: Sunil Shahu <shshahu@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The station MLME and IBSS/mesh ones use entirely different
code for interpreting HT and VHT operation elements. Change
the code that interprets them a bit - it now modifies an
existing chandef - and use it also in the MLME code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In VHT, the specification allows to limit the number of
MSDUs in an A-MSDU in the Extended Capabilities IE. There
is also a limitation on the byte size in the VHT IE.
In HT, the only limitation is on the byte size.
Parse the capabilities from the peer and make them
available to the driver.
In HT, there is another limitation when a BA agreement
is active: the byte size can't be greater than 4095.
This is not enforced here.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The minimum chandef bandwidth calculation was done only in case
a new station was inserted (or when an existing station was removed).
However, it is possible that stations are inserted before they are
associated, e.g., when FULL_AP_CLIENT_STATE is supported and user
space adds stations unassociated.
Fix this by calling ieee80211_recalc_min_chandef() whenever
a station transitions in/out the associated state, and only
consider station marked as associated.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers offload some frames internally (e.g.
AddBa). Reporting such frames to mac80211 would
only confuse MLME. However it would be useful to
be able to pass such frames to monitor interfaces
for sniffing purposes, e.g. when running AP +
monitor.
To do that allow drivers to tell mac80211 whether
a given frame should be:
- processed but not delivered to any monitor vif
- not processed but delievered to monitor vifs
only
Signed-off-by: Grzegorz Bajorski <grzegorz.bajorski@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enable driver to manage the reordering logic itself.
This is needed for example for the iwlwifi driver that
will support hardware assisted reordering.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The value 5000 was put here with the addition of the timeout field to
ieee80211_start_tx_ba_session. It was originally added in mac80211 to
save resources for drivers like iwlwifi, which only supports a limited
number of concurrent aggregation sessions.
Since iwlwifi does not use minstrel_ht and other drivers don't need
this, 0 is a better default - especially since there have been
recent reports of aggregation setup related issues reproduced with
ath9k. This should improve stability without causing any adverse
effects.
Cc: stable@vger.kernel.org
Acked-by: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The change from cur_tp to the function
minstrel_get_tp_avg/minstrel_ht_get_tp_avg changed the unit used for the
current throughput. For example in minstrel_ht the correct
conversion between them would be:
mrs->cur_tp / 10 == minstrel_ht_get_tp_avg(..).
This factor 10 must also be included in the calculation of
minstrel_get_expected_throughput and minstrel_ht_get_expected_throughput to
return values with the unit [Kbps] instead of [10Kbps]. Otherwise routing
algorithms like B.A.T.M.A.N. V will make incorrect decision based on these
values. Its kernel based implementation expects expected_throughput always
to have the unit [Kbps] and not sometimes [10Kbps] and sometimes [Kbps].
The same requirement has iw or olsrdv2's nl80211 based statistics module
which retrieve the same data via NL80211_STA_INFO_TX_BITRATE.
Cc: stable@vger.kernel.org
Fixes: 6a27b2c40b ("mac80211: restructure per-rate throughput calculation into function")
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Patch fixes this splat
BUG: KASAN: slab-out-of-bounds in minstrel_ht_update_stats.isra.7+0x6e1/0x9e0
[mac80211] at addr ffff8800cee640f4 Read of size 4 by task swapper/3/0
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Link: http://lkml.kernel.org/r/CALYGNiNyJhSaVnE35qS6UCGaSb2Dx1_i5HcRavuOX14oTz2P+w@mail.gmail.com
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
"This looks like a lot but it's a mixture of regression fixes as well
as fixes for longer standing issues.
1) Fix on-channel cancellation in mac80211, from Johannes Berg.
2) Handle CHECKSUM_COMPLETE properly in xt_TCPMSS netfilter xtables
module, from Eric Dumazet.
3) Avoid infinite loop in UDP SO_REUSEPORT logic, also from Eric
Dumazet.
4) Avoid a NULL deref if we try to set SO_REUSEPORT after a socket is
bound, from Craig Gallek.
5) GRO key comparisons don't take lightweight tunnels into account,
from Jesse Gross.
6) Fix struct pid leak via SCM credentials in AF_UNIX, from Eric
Dumazet.
7) We need to set the rtnl_link_ops of ipv6 SIT tunnels before we
register them, otherwise the NEWLINK netlink message is missing
the proper attributes. From Thadeu Lima de Souza Cascardo.
8) Several Spectrum chip bug fixes for mlxsw switch driver, from Ido
Schimmel
9) Handle fragments properly in ipv4 easly socket demux, from Eric
Dumazet.
10) Don't ignore the ifindex key specifier on ipv6 output route
lookups, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (128 commits)
tcp: avoid cwnd undo after receiving ECN
irda: fix a potential use-after-free in ircomm_param_request
net: tg3: avoid uninitialized variable warning
net: nb8800: avoid uninitialized variable warning
net: vxge: avoid unused function warnings
net: bgmac: clarify CONFIG_BCMA dependency
net: hp100: remove unnecessary #ifdefs
net: davinci_cpdma: use dma_addr_t for DMA address
ipv6/udp: use sticky pktinfo egress ifindex on connect()
ipv6: enforce flowi6_oif usage in ip6_dst_lookup_tail()
netlink: not trim skb for mmaped socket when dump
vxlan: fix a out of bounds access in __vxlan_find_mac
net: dsa: mv88e6xxx: fix port VLAN maps
fib_trie: Fix shift by 32 in fib_table_lookup
net: moxart: use correct accessors for DMA memory
ipv4: ipconfig: avoid unused ic_proto_used symbol
bnxt_en: Fix crash in bnxt_free_tx_skbs() during tx timeout.
bnxt_en: Exclude rx_drop_pkts hw counter from the stack's rx_dropped counter.
bnxt_en: Ring free response from close path should use completion ring
net_sched: drr: check for NULL pointer in drr_dequeue
...
Use kzalloc instead of kmalloc for struct tid_ampdu_rx to
initialize the "removed" field (all others are initialized
manually). That fixes:
UBSAN: Undefined behaviour in net/mac80211/rx.c:932:29
load of value 2 is not a valid value for type '_Bool'
CPU: 3 PID: 1134 Comm: kworker/u16:7 Not tainted 4.5.0-rc1+ #265
Workqueue: phy0 rt2x00usb_work_rxdone
0000000000000004 ffff880254a7ba50 ffffffff8181d866 0000000000000007
ffff880254a7ba78 ffff880254a7ba68 ffffffff8188422d ffffffff8379b500
ffff880254a7bab8 ffffffff81884747 0000000000000202 0000000348620032
Call Trace:
[<ffffffff8181d866>] dump_stack+0x45/0x5f
[<ffffffff8188422d>] ubsan_epilogue+0xd/0x40
[<ffffffff81884747>] __ubsan_handle_load_invalid_value+0x67/0x70
[<ffffffff82227b4d>] ieee80211_sta_reorder_release.isra.16+0x5ed/0x730
[<ffffffff8222ca14>] ieee80211_prepare_and_rx_handle+0xd04/0x1c00
[<ffffffff8222db03>] __ieee80211_rx_handle_packet+0x1f3/0x750
[<ffffffff8222e4a7>] ieee80211_rx_napi+0x447/0x990
While at it, convert to use sizeof(*tid_agg_rx) instead.
Fixes: 788211d81b ("mac80211: fix RX A-MPDU session reorder timer deletion")
Cc: stable@vger.kernel.org
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
[reword commit message, use sizeof(*tid_agg_rx)]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During a sw scan ieee80211_iface_work ignores work items for all vifs.
However after the scan complete work is requeued only for STA, ADHOC
and MESH iftypes.
This occasionally results in event processing getting delayed/not
processed for iftype AP when it coexists with a STA. This can result
in data halt and eventually disconnection on the AP interface.
Cc: stable@vger.kernel.org
Signed-off-by: Sachin Kulkarni <Sachin.Kulkarni@imgtec.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With upcoming CONFIG_UBSAN the following BUILD_BUG_ON in
net/mac80211/debugfs.c starts to trigger:
BUILD_BUG_ON(hw_flag_names[NUM_IEEE80211_HW_FLAGS] != (void *)0x1);
It seems, that compiler instrumentation causes some code
deoptimizations. Because of that GCC is not being able to resolve
condition in BUILD_BUG_ON() at compile time.
We could make size of hw_flag_names array unspecified and replace the
condition in BUILD_BUG_ON() with following:
ARRAY_SIZE(hw_flag_names) != NUM_IEEE80211_HW_FLAGS
That will have the same effect as before (adding new flag without
updating array will trigger build failure) except it doesn't fail with
CONFIG_UBSAN. As a bonus this patch slightly decreases size of
hw_flag_names array.
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently mac80211 does not inform the driver of the session
block ack timeout when starting a rx aggregation session.
Drivers that manage the reorder buffer need to know this
parameter.
Seeing that there are now too many arguments for the
drv_ampdu_action() function, wrap them inside a structure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use to_delayed_work() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently mac80211 does not inform the driver of the window
size when starting an RX aggregation session.
To enable managing the reorder buffer in the driver or hardware
the window size is needed.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an option for driver to check for packet duplication
by itself.
This is needed for example by the iwlwifi driver which
parallelizes the RX path and does the duplication check
per queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Group ID Management frame is an Action frame of
category VHT. It is transmitted by the AP to assign
or change the user position of a STA for one or more
group IDs.
Process and save the group membership data. Notify
underlying driver of changes.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Non-bufferable MMPDUs are sent out to STAs even while in PS mode
(for example probe responses). Applying filtered frame handling for
these doesn't seem to make much sense and will only create more
air utilization when the STA wakes up. Hence, apply filtered frame
handling only for bufferable MMPDUs.
Discovered while testing an old VOIP phone that started probing
for APs while in PS mode. The mac80211/ath9k AP where the STA is
associated would reply with a probe response but the phone sometimes
moved to a new channel already and couldn't ack the probe response
anymore. In that case mac80211 applied filtered frame handling
for the un-acked probe response.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On hw restart, mac80211 might try to reconfigure already
stopped sched scan, if ieee80211_sched_scan_stopped_work()
wasn't scheduled yet.
This in turn will keep the device driver with scheduled scan
configured, while both mac80211 and cfg80211 will clear
their sched scan state once the work is scheduled.
Fix it by ignoring ieee80211_sched_scan_stopped() calls
while in hw restart, and flush the work before starting
the reconfiguration.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My commit below broken PS-Poll handling. In case the driver
has no frames buffered, driver_release_tids will be 0, but
calling find_highest_prio_tid() with 0 as a parameter is
not a good idea:
fls(0) - 1 = -1.
This bug caused mac80211 to think that frames were buffered
in the driver which in turn was confused because mac80211
was asking to release frames that were not reported to
exist.
On iwlwifi, this led to the WARNING below:
WARNING: CPU: 0 PID: 11230 at drivers/net/wireless/intel/iwlwifi/mvm/sta.c:1733 iwl_mvm_sta_modify_sleep_tx_count+0x2af/0x320 [iwlmvm]()
ffffffffc0627c60 ffff8800069b7648 ffffffff81888913 0000000000000000
0000000000000000 ffff8800069b7688 ffffffff81089d6a ffff8800069b7678
0000000000000001 ffff88003b35abf0 ffff88000698b128 ffff8800069b76d4
Call Trace:
[<ffffffff81888913>] dump_stack+0x4c/0x65
[<ffffffff81089d6a>] warn_slowpath_common+0x8a/0xc0
[<ffffffff81089e5a>] warn_slowpath_null+0x1a/0x20
[<ffffffffc05f36bf>] iwl_mvm_sta_modify_sleep_tx_count+0x2af/0x320 [iwlmvm]
[<ffffffffc05dae41>] iwl_mvm_mac_release_buffered_frames+0x31/0x40 [iwlmvm]
[<ffffffffc045d8b6>] ieee80211_sta_ps_deliver_response+0x6e6/0xd80 [mac80211]
[<ffffffffc0461296>] ieee80211_sta_ps_deliver_poll_response+0x26/0x30 [mac80211]
[<ffffffffc048f743>] ieee80211_rx_handlers+0xa83/0x2900 [mac80211]
[<ffffffffc04917ad>] ieee80211_prepare_and_rx_handle+0x1ed/0xa70 [mac80211]
[<ffffffffc045e3d5>] ? sta_info_get_bss+0x5/0x4a0 [mac80211]
[<ffffffffc04925b6>] ieee80211_rx_napi+0x586/0xcd0 [mac80211]
[<ffffffffc05eaa3e>] iwl_mvm_rx_rx_mpdu+0x59e/0xc60 [iwlmvm]
Fixes: 0ead2510f8 ("mac80211: allow the driver to send EOSP when needed")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On reconfig, in case of sched_scan_req->n_scan_plans > 1,
local->sched_scan_req was never cleared, although
cfg80211_sched_scan_stopped_rtnl() was called, resulting
in local->sched_scan_req holding a stale and preventing
further scheduled scan requests.
Clear it explicitly in this case.
Fixes: 42a7e82c6792 ("mac80211: Do not restart scheduled scan if multiple scan plans are set")
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Defer ROC requests during hw restart, as the driver
might not be fully configured in this stage (e.g.
channel contexts were not added yet)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ilan's previous commit 1b894521e6 ("mac80211: handle HW
ROC expired properly") neglected to take into account that
hw_begun was now always set in the software implementation
as well as the offloaded case.
Fix hw_begun to only apply to the offloaded case to make
the check in Ilan's commit safe and correct.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current (new) code recalculates the new work timeout
for software remain-on-channel whenever any item started.
In two of the callers of ieee80211_handle_roc_started(),
this is completely pointless since they're for hardware
and will skip the recalculation entirely; it's necessary
only in the case of having just added a new item to the
list, as in the last remaining case the recalculation had
just been done.
This last case, however, is also problematic - if one of
the items on the list actually expires during the recalc
the list iteration outside becomes corrupted and crashes.
Fix this by moving the recalculation to the only place
where it's required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
An AP can send an operating channel width change in a beacon
opmode notification IE as long as there's a change in the nss as
well (See 802.11ac-2013 section 10.41).
So don't limit updating to nss only from an opmode notification IE.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the AP is advertising limited TX power, the message can be
printed over and over again. Suppress it when the power level
isn't changing.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=106011
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During reprogramming, mac80211 currently first adds all the channel
contexts, then binds them to the vifs and then goes to reconfigure
all the interfaces. Drivers might, perhaps implicitly, rely on the
operation order for certain things that typically happen within a
single function elsewhere in mac80211. To avoid problems with that,
reorder the code in mac80211's restart/reprogramming to work fully
within the interface loop so that the order of operations is like
in normal operation.
For iwlwifi, this fixes a firmware crash when reprogramming with an
AP/GO interface active.
Reported-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When reconfiguration during resume fails while a scan is pending
for completion work, that work will never run, and the scan will
be stuck forever. Factor out the code to recover this and call it
also in ieee80211_handle_reconfig_failure().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of HW ROC, when the driver reports that the ROC expired,
it is not sufficient to purge the ROCs based on the remaining
time, as it possible that the device finished the ROC session
before the actual requested duration.
To handle such cases, in case of ROC expired notification from
the driver, complete all the ROCs which are marked with hw_begun,
regardless of the remaining duration.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When cancelling, you can cancel "any" (first in list) mgmt-tx
or remain-on-channel operation by using the value 0 for the
cookie along with the *opposite* operation, i.e.
* cancel the first mgmt-tx by cancelling roc with 0 cookie
* cancel the first roc by cancelling mgmt-tx with 0 cookie
This isn't really that bad since userspace should only pass
cookies that we gave it, but could lead to hard-to-debug
issues so better prevent it and reject zero values since we
never hand those out.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While it was possible to create an IBSS with 80+80 MHz channel, joining
such an IBSS resulted in falling back to 20 MHz channel with VHT
disabled due to a missing switch case for 80+80.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jouni found a bug in the remain-on-channel logic: when a short item
is queued, a long item is combined with it extending the original
one, and then the long item is deleted, the timeout doesn't go back
to the short one, and the short item ends up taking a long time. In
this case, this showed as blocking scan when running two test cases
back to back - the scan from the second was delayed even though all
the remain-on-channel items should long have been gone.
Fixing this with the current data structures turns out to be a bit
complicated, we just remove the long item from the dependents list
right now and don't recalculate the timeouts.
There's a somewhat similar bug where we delete the short item and
all the dependents go with it; to fix this we'd have to move them
from the dependents to the real list.
Instead of trying to do that, rewrite the code to not have all this
complexity in the data structures: use a single list and allow more
than one entry in it being marked as started. This makes the code a
bit more complex, the worker needs to understand that it might need
to just remove one of the started items, while keeping the device
off-channel, but that's not more complicated than the nested data
structures.
This then fixes both issues described, and makes it easier to also
limit the overall off-channel time when combining.
TODO: as before, with hardware remain-on-channel, deleting an item
after combining results in cancelling them all - we can keep track
of the time elapsed and only cancel after that to fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the cookie is assigned inside ieee80211_make_ack_skb()
now, we no longer need to return the ack_skb as the cookie
and can simplify the function's return and the callers. Also
rename it to ieee80211_attach_ack_skb() to more accurately
reflect its purpose.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is quite a bit of code that logically depends here since
it has to deal with all the remain-on-channel logic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a mgmt-tx operation is aborted before it runs, the wrong
cookie is reported back to userspace, and the ack_skb gets
leaked since the frame is freed directly instead of freeing
it using ieee80211_free_txskb(). Fix that.
Fixes: 3b79af973c ("mac80211: stop using pointers as userspace cookies")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If some code stops the queues more times than having started
(for when refcounting is used), warn on and reset the counter
to 0 to avoid blocking forever.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When freeing the TX skb for an off-channel TX, use the correct
API to also free the ACK skb that might have been allocated.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a new station is added to AP/GO interfaces the default behaviour
is for it to be added authenticated and associated, due to backwards
compatibility. To prevent that, the driver must be able to do that
(setting the NL80211_FEATURE_FULL_AP_CLIENT_STATE feature flag) and
userspace must set the flag mask to auth|assoc and clear the set.
Handle this quirk in the API entirely in nl80211, and always push the
full flags to the drivers. NL80211_FEATURE_FULL_AP_CLIENT_STATE is
still required for userspace to be allowed to set the mask including
those bits, but after checking that add both flags to the mask and
set in case userspace didn't set them otherwise.
This obsoletes the mac80211 code handling this difference, no other
driver is currently using these flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit adds implementation for abort scan in mac80211.
Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com>
[adjust to wdev change in previous patch and clean up code a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add new VIF flag, that will allow get NOA update
notification when driver will request this, even
this is not pure P2P vif (eg. STA vif).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
add ieee80211_iter_keys_rcu() to iterate over uploaded
keys in atomic context (when rcu is locked)
The station removal code removes the keys only after
calling synchronize_net(), so it's not safe to iterate
the keys at this point (and postponing the actual key
deletion with call_rcu() might result in some
badly-ordered ops calls).
Add a flag to indicate a station is being removed,
and skip the configured keys if it's set.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can happen when the driver needs to send less frames
than expected and then needs to close the SP.
Mac80211 still needs to set the more_data properly based
on its buffer state (ps_tx_buffer and buffered frames on
other TIDs).
To that end, refactor the code that delivers frames upon
uAPSD trigger frames to be able to get only the more_data
bit without actually delivering those frames in case the
driver is just asking to set a NDP with EOSP and MORE_DATA
bit properly set.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This really should never happen except very early in the process
of bringing up a new driver, at which point you'll have to add
more debugging in the driver and this string isn't useful. Remove
it and save some size (when it's even compiled in.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no point in printing the mpath pointer since it can't
be used for anything - print the MAC address instead (like in
the forwarding case.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices or drivers cannot deal with having the same station
address for different virtual interfaces, say as a client to two
virtual AP interfaces. Rather than requiring each driver with a
limitation like that to enforce it, add a hardware flag for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the last change here, I neglected to update the cookie in one code
path: when a mgmt-tx has no real cookie sent to userspace as it doesn't
wait for a response, but is off-channel. The original code used the SKB
pointer as the cookie and always assigned the cookie to the TX SKB in
ieee80211_start_roc_work(), but my change turned this around and made
the code rely on a valid cookie being passed in.
Unfortunately, the off-channel no-wait TX path wasn't assigning one at
all, resulting in an uninitialized stack value being used. This wasn't
handed back to userspace as a cookie (since in the no-wait case there
isn't a cookie), but it was tested for non-zero to distinguish between
mgmt-tx and off-channel.
Fix this by assigning a dummy non-zero cookie unconditionally, and get
rid of a misleading comment and some dead code while at it. I'll clean
up the ACK SKB handling separately later.
Fixes: 3b79af973c ("mac80211: stop using pointers as userspace cookies")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
DFS channels should not be actively scanned as we can't be sure
if we are allowed or not.
If the current channel is in the DFS band, active scan might be
performed after CSA, but we have no guarantee about other channels,
therefore it is safer to prevent active scanning at all.
Cc: stable@vger.kernel.org
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Interfaces are being initialized (setup) on addition,
and torn down on removal.
However, p2p device is being torn down when stopped,
resulting in the next p2p start operation being done
on uninitialized interface.
Solve it by calling ieee80211_teardown_sdata() only
on interface removal (for the non-netdev case).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[squashed in fix to call teardown after unregister]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Advertising reordering window in ADDBA less than 64 can crash some APs,
an example is LinkSys WRT120N (with FW v1.0.07 build 002 Jun 18 2012).
On the other hand, a driver may need to limit Tx A-MPDU size for its own
reasons, like specific HW limitations.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using call_rcu(), the called function may be delayed quite
significantly, and without a matching rcu_barrier() there's no
way to be sure it has finished.
Therefore, global state that could be gone/freed/reused should
never be touched in the callback.
Fix this in mesh by moving the atomic_dec() into the caller;
that's not really a problem since we already unlinked the path
and it will be destroyed anyway.
This fixes a crash Jouni observed when running certain tests in
a certain order, in which the mesh interface was torn down, the
memory reused for a function pointer (work struct) and running
that then crashed since the pointer had been decremented by 1,
resulting in an invalid instruction byte stream.
Cc: stable@vger.kernel.org
Fixes: eb2b9311fd ("mac80211: mesh path table implementation")
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For now, this feature doesn't actually work. To avoid shipping a
kernel that has it enabled but where it can't be used disable it
for now - we can re-enable it when it's fixed.
This partially reverts 44674d9c22 ("mac80211: advertise support
for full station state in AP mode").
Cc: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel context driver operations can sleep, so add might_sleep()
and document this.
Signed-off-by: Chaitanya T K <chaitanya.mgit@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow distinguishing the non-station case from the case of a
station without rates, by using -1 for the non-station case.
This value cannot be reached with a station since that many
legacy rates don't exist.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As WMM is required for HT/VHT operation, treat bad WMM parameters
more gracefully by falling back to default parameters instead of
not using WMM assocation. This makes it possible to still use HT
or VHT, although potentially with reduced quality of service due
to unintended WMM parameters.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Disabling WMM has a huge impact these days. It implies that
HT and VHT will be disabled which means that the throughput
will be drammatically reduced.
Since the AIFSN is a transmission parameter, we can play a
bit and fix it up to make it compliant with the 802.11
specification which requires it to be at least 2.
Increasing it from 1 to 2 will slightly reduce the
likelyhood to get a transmission opportunity compared to
other clients that would accept to set AIFSN=1, but at
least it will allow HT and VHT which is a huge gain.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function currently determines this value, for use in bss_info.qos,
based on the interface type itself. Make it a parameter instead and
set it with the same logic for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
llid_in_use needs to be limited to stations of the same VIF, otherwise it
will cause a NULL deref as the sta_info of non-mesh-VIFs don't have
sta->mesh set.
Steps to reproduce:
modprobe mac80211_hwsim channels=2
iw phy phy0 interface add ibss0 type ibss
iw phy phy0 interface add mesh0 type mp
iw phy phy1 interface add ibss1 type ibss
iw phy phy1 interface add mesh1 type mp
ip link set ibss0 up
ip link set mesh0 up
ip link set ibss1 up
ip link set mesh1 up
iw dev ibss0 ibss join foo 2412
iw dev ibss1 ibss join foo 2412
# Ensure that ibss0 and ibss1 are actually associated; I often need to
# leave and join the cell on ibss1 a second time.
iw dev mesh0 mesh join bar
iw dev mesh1 mesh join bar # crash
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When 11n peers performs a TDLS connection on a legacy BSS, the HT
operation IE must be specified according to IEEE802.11-2012 section
9.23.3.2. Otherwise HT-protection is compromised and the medium becomes
noisy for both the TDLS and the BSS links.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Scheduled scan has to be reconfigured only if wowlan wasn't
configured, since otherwise it should continue to run (with
the 'any' trigger) or be aborted.
The current code will end up asking the driver to start a new
scheduled scan without stopping the previous one, and leaking
some memory (from the previous request.)
Fix this by doing the abort/restart under the proper conditions.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If drv_start() fails during hw_restart, all the running
interfaces are being closed/stopped, which results in
drv_stop() being called, although the driver was never
started successfully.
This might cause drivers to perform operations on uninitialized
memory (as they assume it was initialized on drv_start)
Consider the local->started flag, and call the driver's stop()
op only if drv_start() succeeded before.
Move drv_start() and drv_stop() to driver-ops.c, as they are no
longer simple wrappers.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The recalc_smps work can run after the station disassociates.
At this stage we already released the channel, but the work
will be cancelled only when the interface stops.
In this scenario we can hit the warning in ieee80211_recalc_smps, so
just remove it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Requesting hw restart during suspend might result
in the restart work being executed after mac80211
and the hw are suspended.
Solve the race by simply scheduling the restart
work on a freezable workqueue.
Note that there can be some cases of reconfiguration
on resume (besides the hardware restart):
* wowlan is not configured -
All the interfaces removed were removed on suspend,
and drv_stop() was called. At this point the driver
shouldn't expect for hw_restart anyway, so we can
simply cancel it (on resume).
* wowlan is configured, drv_resume() == 1
There is no definitive expected behavior in this case,
as each driver might have different expectations (e.g.
setting some flags on suspend/restart vs. not handling
spurious recovery).
For now, simply let the hw_restart work run again after
resume, and hope the driver will handle it well (or at
least initiate another hw restart).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Local request to deauthenticate wasn't handled while associating, thus
the association could continue even when the user space required to
disconnect.
Cc: stable@vger.kernel.org
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In TDLS channel-switch operations the chandef can sometimes be NULL.
Avoid an oops in the trace code for these cases and just print a
chandef full of zeros.
Cc: stable@vger.kernel.org
Fixes: a7a6bdd067 ("mac80211: introduce TDLS channel switch ops")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of one shot NOA the interval can be 0, catch that
instead of potentially (depending on the driver) crashing
like this:
divide error: 0000 [#1] SMP
[...]
Call Trace:
<IRQ>
[<ffffffffc08e891c>] ieee80211_extend_absent_time+0x6c/0xb0 [mac80211]
[<ffffffffc08e8a17>] ieee80211_update_p2p_noa+0xb7/0xe0 [mac80211]
[<ffffffffc069cc30>] ath9k_p2p_ps_timer+0x170/0x190 [ath9k]
[<ffffffffc070adf8>] ath_gen_timer_isr+0xc8/0xf0 [ath9k_hw]
[<ffffffffc0691156>] ath9k_tasklet+0x296/0x2f0 [ath9k]
[<ffffffff8107ad65>] tasklet_action+0xe5/0xf0
[...]
Cc: stable@vger.kernel.org [3.16+, due to d463af4a1c using it]
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* I merged net-next back to avoid a conflict with the
* cfg80211 scheduled scan API extensions
* preparations for better scan result timestamping
* regulatory cleanups
* mac80211 statistics cleanups
* a few other small cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=uZ5N
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Here's another set of patches for the current cycle:
* I merged net-next back to avoid a conflict with the
* cfg80211 scheduled scan API extensions
* preparations for better scan result timestamping
* regulatory cleanups
* mac80211 statistics cleanups
* a few other small cleanups and fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Group station statistics by where they're (mostly) updated
(TX, RX and TX-status) and group them into sub-structs of
the struct sta_info.
Also rename the variables since the grouping now makes it
obvious where they belong.
This makes it easier to identify where the statistics are
updated in the code, and thus easier to think about them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's little point in keeping (and even sending to userspace)
the beacon_loss_count value per station, since it can only apply
to the AP on a managed-mode connection. Move the value to ifmgd,
advertise it only in managed mode, and remove it from ethtool as
it's available through better interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This file only feeds a debugfs file that isn't very useful, so remove
it. If necessary, we can add other ways to get this information, for
example in the NL80211_CMD_PROBE_CLIENT response.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
That file contains just a single function, which itself is just a
single statement to call a different function. Remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's only a single caller of this function, so it can
be moved to the same file and made static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As this API has never really seen any use and most drivers don't
ever use the value derived from it, remove it.
Change the only driver using it (rt2x00) to simply use the DTIM
period instead of the "max sleep" time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If multiple scan plans were set for scheduled scan, do not restart
scheduled scan on reconfig because it is possible that some scan
plans were already completed and there is no need to run them all
over again. Instead, notify userspace that scheduled scan stopped
so it can configure new scan plans for scheduled scan.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 30686bf7f5 ("mac80211: convert HW flags to unsigned long
bitmap") accidentally removed the newline delimiter from the hwflags
debugfs file. Fix this by adding back the newline between the HW flags.
Cc: stable@vger.kernel.org [4.2]
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
[fix commit log]
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 5c48f12017.
Some device drivers (ath10k) offload part of aggregation including AddBA/DelBA
negotiations to firmware. In such scenario, the PMF configuration of
the station needs to be provided to driver to enable encryption of
AddBA/DelBA action frames.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* many internal fixes, API improvements, cleanups, etc.
* full AP client state tracking in cfg80211/mac80211 from Ayala
* VHT support (in mac80211) for mesh
* some A-MSDU in A-MPDU support from Emmanuel
* show current TX power to userspace (from Rafał)
* support for netlink dump in vendor commands (myself)
-----BEGIN PGP SIGNATURE-----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=BF9F
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-10-05' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For the current cycle, we have the following right now:
* many internal fixes, API improvements, cleanups, etc.
* full AP client state tracking in cfg80211/mac80211 from Ayala
* VHT support (in mac80211) for mesh
* some A-MSDU in A-MPDU support from Emmanuel
* show current TX power to userspace (from Rafał)
* support for netlink dump in vendor commands (myself)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The function returns always non-negative values.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mac80211 code uses ktime_get_ts to measure the connected time.
As this uses monotonic time, it is y2038 safe on 32-bit systems,
but we still want to deprecate the use of 'timespec' because most
other users are broken.
This changes the code to use ktime_get_seconds() instead, which
avoids the timespec structure and is slightly more efficient.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of int with 0/1, use bool with false/true for the
powersave argument to ieee80211_send_nullfunc().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of nesting two if statements, inline the second
check into the first if statement and to indentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using software queueing, tx sequence number assignment happens at
ieee80211_tx_dequeue time, so the fast-xmit codepath must not do that.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enables adding stations in unauthenticated mode, just after
receiving the first authentication frame; which in turn allows
sending a negative authentication reply if the station cannot be
added.
In addition init rate control for unassociated station only when
it becomes associated, prior to that low rates will be used.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For certain tests, for example replay detection, it can be useful
to be able to influence/set the PN used in outgoing packets. Make
it possible to change the TX PN in debugfs.
For now, this doesn't support TKIP since I haven't needed it, but
there's no reason it couldn't be added if necessary.
Note that this must be used very carefully: it could, for example,
be used to make "valid replays" where the PN reuse happens on a
different TID. This couldn't be done by an attacker since the TID
is protected as part of the AAD.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this .config: http://busybox.net/~vda/kernel_config_ALLYES_Os,
after deinlining these functions have sizes and callsite counts
as follows:
drv_get_tsf: 634 bytes, 6 calls
drv_set_tsf: 626 bytes, 2 calls
drv_reset_tsf: 617 bytes, 2 calls
Total size reduction is about 4.2 kbytes.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Johannes Berg <johannes.berg@intel.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
CC: linux-wireless@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this .config: http://busybox.net/~vda/kernel_config_ALLYES_Os,
after deinlining the function size is 755 bytes and there are
6 callsites.
Total size reduction is about 3.3 kbytes.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Johannes Berg <johannes.berg@intel.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
CC: linux-wireless@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this .config: http://busybox.net/~vda/kernel_config_ALLYES_Os,
after deinlining the function size is 821 bytes and there are
2 callsites, reducing code size by about 800 bytes.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Johannes Berg <johannes.berg@intel.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
CC: linux-wireless@vger.kernel.org
CC: linux-kernel@vger.kernel.org
[adjust code-style a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there are no supported rates in the rate mask with the required
flags, we warn, but it's not clear which part causes the warning.
Add the relevant data to the warning to understand why it happens.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replace the average symbol by "avg" to avoid being warned about the
non-ASCII symbol all the time, line up the columns properly.
(I changed my mind - the warnings are getting annoying)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of "any" wowlan trigger, there is no reason to tear down
aggregations, as we want the device to continue working normally.
Similarly, there's no reason to tear down aggregations on resume,
as they should have been torn down on suspend if needed.
However, since the reconfiguration flow is shared with HW restart,
tear down aggregations on reconfiguration when we are not resuming.
To keep things working after non-wowlan suspend, keep clearing the
WLAN_STA_BLOCK_BA flag.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this .config: http://busybox.net/~vda/kernel_config_ALLYES_Os,
after deinlining these functions have sizes and callsite counts
as follows:
drv_add_interface: 638 bytes, 5 calls
drv_remove_interface: 611 bytes, 6 calls
drv_change_interface: 658 bytes, 1 call
Total size reduction is about 9 kbytes.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
CC: Johannes Berg <johannes.berg@intel.com>
CC: linux-wireless@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this .config: http://busybox.net/~vda/kernel_config_ALLYES_Os,
after deinlining the function size is 706 bytes and there are
2 callsites, reducing code size by about 700 bytes.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
CC: Johannes Berg <johannes.berg@intel.com>
CC: linux-wireless@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this .config: http://busybox.net/~vda/kernel_config_ALLYES_Os,
after deinlining the function size is 785 bytes and there are
7 callsites.
Total size reduction is about 3.5 kbytes.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
CC: Johannes Berg <johannes.berg@intel.com>
CC: linux-wireless@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When debugging wireless powersave issues on the AP side it's quite helpful
to see our own beacons that are transmitted by the hardware/driver. However,
this is not that easy since beacons don't pass through the regular TX queues.
Preferably drivers would call ieee80211_tx_status also for tx'ed beacons
but that's not always possible. Hence, just send a copy of each beacon
generated by ieee80211_beacon_get_tim to monitor devices when they are
getting fetched by the driver.
Also add a HW flag IEEE80211_HW_BEACON_TX_STATUS that can be used by
drivers to indicate that they report TX status for beacons.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
(with a fix from Christian Lamparted rolled in)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes dropped packets in the tx path in case a non-PS station triggers
the tx filter.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current behavior of notifying CQM events is inconsistent:
Upon first configuration there is a cqm event with the current
status according to threshold configured, regardless of signal
stability.
When there is reconfiguration no event is sent unless there is
a significant change to the signal level according to the new
configuration.
Since the current reconfiguration behavior might cause missing
CQM events in case the current signal did not change but is on
the other side of the new threshold, fix that by resetting the
stored signal level upon reconfiguration.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows ieee80211_tx_monitor to be used directly for sending 802.11 frames
to all monitor interfaces.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It doesn't seem problematic to change the weight for the average
beacon signal from 3 to 4, so use DECLARE_EWMA. This also makes
the code easier to maintain since bugs like the one fixed in the
previous patch can't happen as easily.
With a fix from Avraham Stern to invert the sign since EMWA uses
unsigned values only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ifmgd->ave_beacon_signal value cannot be taken as is for
comparisons, it must be divided by since it's represented
like that for better accuracy of the EWMA calculations. This
would lead to invalid driver RSSI events. Fix the used value.
Fixes: 615f7b9bb1 ("mac80211: add driver RSSI threshold events")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These file aren't really useful:
- if per beacon data is required then you need to use
radiotap or similar anyway, debugfs won't help much
- average beacon signal is reported in station info in
nl80211 and can be looked up with iw
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement the basics required for supporting very high throughput
with mesh: include VHT information elements in beacons, probe
responses, and peering action frames, and check for compatible VHT
configurations when peering.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clear the Channel Center Frequency Segment 2 in VHT operation
IEs to avoid sending non-zero values if the SKB wasn't zeroed
before adding the VHT operation IE.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[change commit message a bit - not necessarily just mesh related]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers may be interested in receiving A-MSDU within A-MDPU.
Not all the devices may be able to do so, make it configurable.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The direct probe step before authentication was done mostly for
two reasons:
1) the BSS data could be stale
2) the beacon might not have included all IEs
The concern (1) doesn't really seem to be relevant any more as
we time out BSS information after about 30 seconds, and in fact
the original patch only did the direct probe if the data was
older than the BSS timeout to begin with. This condition got
(likely inadvertedly) removed later though.
Analysing this in more detail shows that since we mostly use
data from the association response, the only real reason for
needing the probe response was that the code validates the WMM
parameters, and those are optional in beacons. As the previous
patches removed that behaviour, we can now remove the direct
probe step entirely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Advertise the capability to send A-MSDU within A-MPDU
in the AddBA request sent by mac80211. Let the driver
know about the peer's capabilities.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the cfg80211's frame registration api receives wdev, however
mac80211 assumes per device filter configuration and ignores wdev.
Per device filtering is too wasteful, especially for multi-channel
devices.
Introduce new per vif frame registration API and use it for probe
request registrations in ieee80211_mgmt_frame_register()
Also call directly to ieee80211_configure_filter instead of using a work
since it is now allowed to sleep in ieee80211_mgmt_frame_register.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When checking if a TDLS chandef can be upgraded, IR-relaxation can be
taken into account to allow more channels.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes we are interested in testing TDLS performance in a specific
width setting. Add the ability to disable the wider-band feature, thereby
allowing the TDLS channel width to be controlled by the BSS width.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Queued frames aren't processed during scan, which results in an inability
to complete the BA session establishment until the scan ends. Since we
can't tx frames until the BA agreement setup is complete, it might result
in a very large latency during scan.
Fix this by allowing to process queued skbs while scanning in HW. This
should be ok since the devices which support hw scan should be able
to handle tx/rx while scanning.
During SW scan, mac80211 drops any txed frames besides probes and NDPs,
so it is still needed to delay processing of the queued frames till the
SW scan is done.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The HT MCS mask has 9 bytes, the VHT one only has 8 streams.
Split the loops to handle this correctly.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When beacon filtering is enabled the mac80211 software implementation
for RSSI CQM cannot work as beacons will not be available. Rather than
accepting such a configuration without proper effect, reject it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently if 80MHz channels are not allowed for use, the VHT IE is not
included in the probe request for an AP. This is not good enough if the
AP is configured with the wrong regulatory and supports VHT even where
prohibited or in TDLS scenarios.
Mark the ifmgd with the DISABLE_VHT flag for the misbehaving-AP case, and
unset VHT support from the peer-station entry for the TDLS case.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
HT TDLS traffic should be protected in a non-HT BSS to avoid
collisions. Therefore, when TDLS peers join/leave, check if
protection is (now) needed and set the ht_operation_mode of
the virtual interface according to the HT capabilities of the
TDLS peer(s).
This works because a non-HT BSS connection never sets (or
otherwise uses) the ht_operation_mode; it just means that
drivers must be aware that this field applies to all HT
traffic for this virtual interface, not just the traffic
within the BSS. Document that.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The rate_control_cap_mask() function takes a parameter mcs_mask, which
GCC will take to be u8 * even though it was declared with a fixed size.
This causes the following warning:
net/mac80211/rate.c: In function 'rate_control_cap_mask':
net/mac80211/rate.c:719:25: warning: 'sizeof' on array function parameter 'mcs_mask' will return size of 'u8 * {aka unsigned char *}' [-Wsizeof-array-argument]
for (i = 0; i < sizeof(mcs_mask); i++)
^
net/mac80211/rate.c:684:10: note: declared here
u8 mcs_mask[IEEE80211_HT_MCS_MASK_LEN],
^
This can be easily fixed by using the IEEE80211_HT_MCS_MASK_LEN directly
within the loop condition.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of using the out-of-line average calculation, use the new
DECLARE_EWMA() macro to declare a signal EWMA, and use that.
This actually *reduces* the code size slightly (on x86-64) while
also reducing the station info size by 80 bytes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
