This avoids a race condition where complete(tx_complete) could be called
before tx_complete is initialized.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemented separate irq handling for edge and level type interrupt
configuration. For edge type interrupts calls to disable_irq_nosync()
and enable_irq() are removed. The at86rf230 resets the irq line only
after the irq status register is read. Disabling the irq can lock the
driver in situations where a irq is set by the radio while the driver
is still reading the frame buffer.
With irq_type configuration set to 0 the original behavior is
preserverd.
Additional the irq filter register is set to filter out all unused
interrupts and the irq status register is read in the probe
function to clear the irq line.
Signed-off-by: Sascha Herrmann <sascha@ps.nvbi.de>
Conflicts:
drivers/net/ieee802154/at86rf230.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Add option to at86rf230 platform data to configure the type of the
interrupt used by the driver. The irq polarity of the device will
be configured accordingly.
Signed-off-by: Sascha Herrmann <sascha@ps.nvbi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_spi_driver() makes the code simpler by eliminating
boilerplate code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the MRF24J40, link-layer acknowledgment request and retry must be
turned on explicitly for each packet. Turn this on in the hardware based
on the FC_ACK_REQ bit being set in the packet.
Also, now that failure to receive an ACK will cause the hardware to report
failure of transmission, change the log level for this failure to debug
level.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
In at86rf230_probe() lp was first set to dev->priv and a few lines later
dev->priv was set to lp again, without changing lp in between. The call
to ieee802154_unregister_device() before err_irq: was unreachable.
Signed-off-by: Sascha Herrmann <sascha@ps.nvbi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It served no purpose: we never call it from anywhere in the stack
and the only driver that did implement it (fakehard) merely provided
a dummy value.
There is also considerable doubt whether it would make sense to
even attempt beacon processing at this level in the Linux kernel.
Signed-off-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register names have been wrong since the beginning but it only showed up now
as they are actualy used for the upcoming auto ACK support.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the filter function to update short address, pan id and ieee
address on change. Allowing for hardware address filtering needed for
auto ACK.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load the 64-bit Extended (IEEE) address into the hardware in the proper
byte order.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon consulting the datasheet further, it does indicates a maximum speed
for SCK at 10MHz.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue a warning if a transmit complete interrupt doesn't happen in time.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to implement empty suspend/resume callbacks if there is nothing
to do during suspend/resume. The drivers will behave the same with no callbacks
or empty callbacks during suspend/resume.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
perm_addr is initialized correctly in register_netdevice() so to init it in
drivers is no longer needed.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The network merge brought in a few users of functions that got
deprecated by the workqueue cleanups: the 'system_nrt_wq' is now the
same as the regular system_wq, since all workqueues are now non-
reentrant.
Similarly, remove one use of flush_work_sync() - the regular
flush_work() has become synchronous, and the "_sync()" version is thus
deprecated as being superfluous.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver for the Microchip MRF24J40 802.15.4 WPAN module.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IEEE 802.15.4 standard represents a networking protocol. I don't
exactly know why drivers for this protocol are stored into the root
'driver' folder, but better will be to store them with other
networking stuff. Currently there are only 3 drivers available for
IEEE 802.15.4 stack, so lets do it now with the smallest overhead.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
