* pci/host-rockchip:
PCI: rockchip: Move the deassert of pm/aclk/pclk after phy_init()
PCI: rockchip: Split out rockchip_cfg_atu()
PCI: rockchip: Clean up bit definitions for PCIE_RC_CONFIG_LCS
PCI: rockchip: Correct the use of FTS mask
PCI: rockchip: Remove the pointer to L1 substate cap
PCI: rockchip: Specify the link capability
PCI: rockchip: Fix negotiated lanes calculation
PCI: rockchip: Add Kconfig COMPILE_TEST
PCI: rockchip: Mark RC as common clock architecture
PCI: rockchip: Provide captured slot power limit and scale
PCI: rockchip: Add three new resets as required properties
PCI: Don't attempt to claim shadow copies of ROM
PCI: designware: Check for iATU unroll support after initializing host
PCI: qcom: Fix pp->dev usage before assignment
PCI: designware-plat: Update author email address
PCI: layerscape: Fix drvdata usage before assignment
PCI: designware-plat: Change maintainer to Jose Abreu
Add support for the MSM8996/APQ8096 PCIe controller. MSM8996 supports Gen
1/2, one lane, 3 PCIe root complexes with support for MSI and legacy
interrupts, and it conforms to PCI Express Base 2.1 specification.
Add a post_init callback to qcom_pcie_ops, as the PCIe pipe clocks are only
setup after the phy is powered on. It also adds an ltssm_enable callback
as it is very much different from other supported SoCs in the driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Remove the struct qcom_pcie.dev member, which is a duplicate of the generic
pp.dev member. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the struct qcom_pcie.dbi member, which is a duplicate of the generic
pp.dbi_base member. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The qcom driver never uses the platform drvdata pointer, so don't bother
setting it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCIE_QCOM
drivers/pci/host/Kconfig: bool "Qualcomm PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Note that for non-modular code, MODULE_DEVICE_TABLE is a no-op and
builtin_platform_driver() uses the same init level priority as
module_platform_driver(), so this doesn't change init ordering.
Explicitly disallow driver unbind, since that doesn't have a sensible use
case anyway, and it allows us to drop the ".remove" code for non-modular
drivers.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Stanimir Varbanov <svarbanov@mm-sol.com>
Several DesignWare-based drivers (dra7xx, exynos, imx6, keystone, qcom, and
spear13xx) had similar loops waiting for the link to come up.
Add a generic dw_pcie_wait_for_link() for use by all these drivers so the
waiting is done consistently, e.g., always using usleep_range() rather than
mdelay() and using similar timeouts and retry counts.
Note that this changes the Keystone link training/wait for link strategy,
so we initiate link training, then wait longer for the link to come up
before re-initiating link training.
[bhelgaas: changelog, split into its own patch, update pci-keystone.c, pcie-qcom.c]
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
The PCIe driver reuses the Designware common code for host and MSI
initialization, and also programs the Qualcomm application specific
registers.
[bhelgaas: remove COMPILE_TEST Kconfig dependency]
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
