Jesse Brandeburg reported that commit acaf4e7099 caused a panic
when adding a network namespace while vxlan module was present in
the system:
[<ffffffff814d0865>] vxlan_lowerdev_event+0xf5/0x100
[<ffffffff816e9e5d>] notifier_call_chain+0x4d/0x70
[<ffffffff810912be>] __raw_notifier_call_chain+0xe/0x10
[<ffffffff810912d6>] raw_notifier_call_chain+0x16/0x20
[<ffffffff815d9610>] call_netdevice_notifiers_info+0x40/0x70
[<ffffffff815d9656>] call_netdevice_notifiers+0x16/0x20
[<ffffffff815e1bce>] register_netdevice+0x1be/0x3a0
[<ffffffff815e1dce>] register_netdev+0x1e/0x30
[<ffffffff814cb94a>] loopback_net_init+0x4a/0xb0
[<ffffffffa016ed6e>] ? lockd_init_net+0x6e/0xb0 [lockd]
[<ffffffff815d6bac>] ops_init+0x4c/0x150
[<ffffffff815d6d23>] setup_net+0x73/0x110
[<ffffffff815d725b>] copy_net_ns+0x7b/0x100
[<ffffffff81090e11>] create_new_namespaces+0x101/0x1b0
[<ffffffff81090f45>] copy_namespaces+0x85/0xb0
[<ffffffff810693d5>] copy_process.part.26+0x935/0x1500
[<ffffffff811d5186>] ? mntput+0x26/0x40
[<ffffffff8106a15c>] do_fork+0xbc/0x2e0
[<ffffffff811b7f2e>] ? ____fput+0xe/0x10
[<ffffffff81089c5c>] ? task_work_run+0xac/0xe0
[<ffffffff8106a406>] SyS_clone+0x16/0x20
[<ffffffff816ee689>] stub_clone+0x69/0x90
[<ffffffff816ee329>] ? system_call_fastpath+0x16/0x1b
Apparently loopback device is being registered first and thus we
receive an event notification when vxlan_net is not ready. Hence,
when we call net_generic() and request vxlan_net_id, we seem to
access garbage at that point in time. In setup_net() where we set
up a newly allocated network namespace, we traverse the list of
pernet ops ...
list_for_each_entry(ops, &pernet_list, list) {
error = ops_init(ops, net);
if (error < 0)
goto out_undo;
}
... and loopback_net_init() is invoked first here, so in the middle
of setup_net() we get this notification in vxlan. As currently we
only care about devices that unregister, move access through
net_generic() there. Fix is based on Cong Wang's proposal, but
only changes what is needed here. It sucks a bit as we only work
around the actual cure: right now it seems the only way to check if
a netns actually finished traversing all init ops would be to check
if it's part of net_namespace_list. But that I find quite expensive
each time we go through a notifier callback. Anyway, did a couple
of tests and it seems good for now.
Fixes: acaf4e7099 ("net: vxlan: when lower dev unregisters remove vxlan dev as well")
Reported-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Tested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should use vxlan_dellink() handler in vxlan_exit_net(), since
i) we're not in fast-path and we should be consistent in dismantle
just as we would remove a device through rtnl ops, and more
importantly, ii) in case future code will kfree() memory in
vxlan_dellink(), we would leak it right here unnoticed. Therefore,
do not only half of the cleanup work, but make it properly.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can create a vxlan device with an explicit underlying carrier.
In that case, when the carrier link is being deleted from the
system (e.g. due to module unload) we should also clean up all
created vxlan devices on top of it since otherwise we're in an
inconsistent state in vxlan device. In that case, the user needs
to remove all such devices, while in case of other virtual devs
that sit on top of physical ones, it is usually the case that
these devices do unregister automatically as well and do not
leave the burden on the user.
This work is not necessary when vxlan device was not created with
a real underlying device, as connections can resume in that case
when driver is plugged again. But at least for the other cases,
we should go ahead and do the cleanup on removal.
We don't register the notifier during vxlan_newlink() here since
I consider this event rather rare, and therefore we should not
bloat vxlan's core structure unecessary. Also, we can simply make
use of unregister_netdevice_many() to batch that. fdb is flushed
upon ndo_stop().
E.g. `ip -d link show vxlan13` after carrier removal before
this patch:
5: vxlan13: <BROADCAST,MULTICAST> mtu 1450 qdisc noop state DOWN mode DEFAULT group default
link/ether 1e:47:da:6d:4d:99 brd ff:ff:ff:ff:ff:ff promiscuity 0
vxlan id 13 group 239.0.0.10 dev 2 port 32768 61000 ageing 300
^^^^^
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following call chains indicate that vxlan_fdb_parse() is
under rtnl_lock protection. So if we use __dev_get_by_index()
instead of dev_get_by_index() to find interface handler in it,
this would help us avoid to change interface reference counter.
rtnetlink_rcv()
rtnl_lock()
netlink_rcv_skb()
rtnl_fdb_add()
vxlan_fdb_add()
vxlan_fdb_parse()
rtnl_unlock()
rtnetlink_rcv()
rtnl_lock()
netlink_rcv_skb()
rtnl_fdb_del()
vxlan_fdb_del()
vxlan_fdb_parse()
rtnl_unlock()
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla posted a patch trying to address following problem :
<quote>
The vxlan driver sets itself as the socket owner for all the TX flows
it encapsulates (using vxlan_set_owner()) and assigns it's own skb
destructor. This causes all tunneled traffic to land up on only one TXQ
as all encapsulated skbs refer to the vxlan socket and not the original
socket. Also, the vxlan skb destructor breaks some functionality for
tunneled traffic like wmem accounting and as TCP small queues and
FQ/pacing packet scheduler.
</quote>
I reworked Sathya patch and added some explanations.
vxlan_xmit() can avoid one skb_clone()/dev_kfree_skb() pair
and gain better drop monitor accuracy, by calling kfree_skb() when
appropriate.
The UDP socket used by vxlan to perform encapsulation of xmit packets
do not need to be alive while packets leave vxlan code. Its better
to keep original socket ownership to get proper feedback from qdisc and
NIC layers.
We use skb->sk to
A) control amount of bytes/packets queued on behalf of a socket, but
prior vxlan code did the skb->sk transfert without any limit/control
on vxlan socket sk_sndbuf.
B) security purposes (as selinux) or netfilter uses, and I do not think
anything is prepared to handle vxlan stacked case in this area.
By not changing ownership, vxlan tunnels behave like other tunnels.
As Stephen mentioned, we might do the same change in L2TP.
Reported-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are same, so unify them as one, pcpu_sw_netstats.
Define pcpu_sw_netstat in netdevice.h, remove pcpu_tstats
from if_tunnel and remove br_cpu_netstats from br_private.h
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding a new vxlan device to an "underlying carrier" (here:
dst->remote_ifindex), the MTU size assigned to the vxlan device
is the MTU at setup time of the carrier - needed headroom, when
adding a vxlan device w/o explicit carrier, then it defaults
to 1500.
In case of an explicit carrier that supports jumbo frames, we
currently cannot change vxlan MTU via ip(8) to > 1500 in
post-setup time, as vxlan driver uses eth_change_mtu() as default
method for manually setting MTU.
Hence, use a custom implementation that only falls back to
eth_change_mtu() in case we didn't use a dev parameter on device
setup time, and otherwise allow a max MTU setting of the carrier
incl. adjustment for headroom.
Reported-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing name of function as part of making the hash in skbuff to be
generic property, not just for receive path.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vxlan_group_used only allows device to leave multicast group
when the remote_ip of this vxlan device is difference from
other vxlan devices' remote_ip. this will cause device not
leave multicast group untile the vn_sock of this vxlan deivce
being released.
The check in vxlan_group_used is not quite precise. since even
the remote_ip is same, but these vxlan devices may use different
lower devices, and they may use different vn_socks.
Only when some vxlan devices use the same vn_sock,same lower
device and same remote_ip, the mc_list of the vn_sock should
not be changed.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In vxlan_open, vxlan_group_used always returns true,
because the state of the vxlan deivces which we want
to open has alreay been running. and it has already
in vxlan_list.
Since ip_mc_join_group takes care of the reference
of struct ip_mc_list. removing vxlan_group_used here
is safe.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise causing dst memory leakage.
Have Checked all other type tunnel device transmit implementation,
no such things happens anymore.
Signed-off-by: Fan Du <fan.du@windriver.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull core locking changes from Ingo Molnar:
"The biggest changes:
- add lockdep support for seqcount/seqlocks structures, this
unearthed both bugs and required extra annotation.
- move the various kernel locking primitives to the new
kernel/locking/ directory"
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
block: Use u64_stats_init() to initialize seqcounts
locking/lockdep: Mark __lockdep_count_forward_deps() as static
lockdep/proc: Fix lock-time avg computation
locking/doc: Update references to kernel/mutex.c
ipv6: Fix possible ipv6 seqlock deadlock
cpuset: Fix potential deadlock w/ set_mems_allowed
seqcount: Add lockdep functionality to seqcount/seqlock structures
net: Explicitly initialize u64_stats_sync structures for lockdep
locking: Move the percpu-rwsem code to kernel/locking/
locking: Move the lglocks code to kernel/locking/
locking: Move the rwsem code to kernel/locking/
locking: Move the rtmutex code to kernel/locking/
locking: Move the semaphore core to kernel/locking/
locking: Move the spinlock code to kernel/locking/
locking: Move the lockdep code to kernel/locking/
locking: Move the mutex code to kernel/locking/
hung_task debugging: Add tracepoint to report the hang
x86/locking/kconfig: Update paravirt spinlock Kconfig description
lockstat: Report avg wait and hold times
lockdep, x86/alternatives: Drop ancient lockdep fixup message
...
In order to enable lockdep on seqcount/seqlock structures, we
must explicitly initialize any locks.
The u64_stats_sync structure, uses a seqcount, and thus we need
to introduce a u64_stats_init() function and use it to initialize
the structure.
This unfortunately adds a lot of fairly trivial initialization code
to a number of drivers. But the benefit of ensuring correctness makes
this worth while.
Because these changes are required for lockdep to be enabled, and the
changes are quite trivial, I've not yet split this patch out into 30-some
separate patches, as I figured it would be better to get the various
maintainers thoughts on how to best merge this change along with
the seqcount lockdep enablement.
Feedback would be appreciated!
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: James Morris <jmorris@namei.org>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Roger Luethi <rl@hellgate.ch>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Simon Horman <horms@verge.net.au>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Wensong Zhang <wensong@linux-vs.org>
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/1381186321-4906-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
trivial patch converting ERR_PTR(PTR_ERR()) into ERR_CAST().
No functional changes.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the burden from the NIC drivers to check if the
vxlan driver is enabled in the kernel and also makes available
the vxlan headrooms to them.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
drivers/net/vxlan.c: In function ‘vxlan_sock_add’:
drivers/net/vxlan.c:2298:11: warning: ‘sock’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/net/vxlan.c:2275:17: note: ‘sock’ was declared here
LD drivers/net/built-in.o
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/usb/qmi_wwan.c
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
include/net/netfilter/nf_conntrack_synproxy.h
include/net/secure_seq.h
The conflicts are of two varieties:
1) Conflicts with Joe Perches's 'extern' removal from header file
function declarations. Usually it's an argument signature change
or a function being added/removed. The resolutions are trivial.
2) Some overlapping changes in qmi_wwan.c and be.h, one commit adds
a new value, another changes an existing value. That sort of
thing.
Signed-off-by: David S. Miller <davem@davemloft.net>
- Move sysctl_local_ports from a global variable into struct netns_ipv4.
- Modify inet_get_local_port_range to take a struct net, and update all
of the callers.
- Move the initialization of sysctl_local_ports into
sysctl_net_ipv4.c:ipv4_sysctl_init_net from inet_connection_sock.c
v2:
- Ensure indentation used tabs
- Fixed ip.h so it applies cleanly to todays net-next
v3:
- Compile fixes of strange callers of inet_get_local_port_range.
This patch now successfully passes an allmodconfig build.
Removed manual inlining of inet_get_local_port_range in ipv4_local_port_range
Originally-by: Samya <samya@twitter.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of RCU api makes vxlan code easier to understand. It also
fixes bug due to missing ACCESS_ONCE() on sk_user_data dereference.
In rare case without ACCESS_ONCE() compiler might omit vs on
sk_user_data dereference.
Compiler can use vs as alias for sk->sk_user_data, resulting in
multiple sk_user_data dereference in rcu read context which
could change.
CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit afbd8bae9c
vxlan: add implicit fdb entry for default destination
creates an implicit fdb entry for default destination. This results
in an invalid fdb entry if default destination is not specified.
For ex:
ip link add vxlan1 type vxlan id 100
creates the following fdb entry
00:00:00:00:00:00 dev vxlan1 dst 0.0.0.0 self permanent
This patch fixes this issue by creating an fdb entry only if a
valid default destination is specified.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes sparse warnings when incorrectly handling the port number
and using int instead of unsigned int iterating through &vn->sock_list[].
Keeping the port as __be16 also makes things clearer wrt endianess.
Also, it was pointed out that vxlan_get_rx_port() had unnecessary checks
which got removed.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds two more ndo ops: ndo_add_rx_vxlan_port() and
ndo_del_rx_vxlan_port().
Drivers can get notifications through the above functions about changes
of the UDP listening port of VXLAN. Also, when physical ports come up,
now they can call vxlan_get_rx_port() in order to obtain the port number(s)
of the existing VXLAN interface in case they already up before them.
This information about the listening UDP port would be used for VXLAN
related offloads.
A big thank you to John Fastabend (john.r.fastabend@intel.com) for his
input and his suggestions on this patch set.
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vxlan-udp-recv function lookup vxlan_sock struct on every packet
recv by using udp-port number. we can use sk->sk_user_data to
store vxlan_sock and avoid lookup.
I have open coded rcu-api to store and read vxlan_sock from
sk_user_data to avoid sparse warning as sk_user_data is not
__rcu pointer.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this patch is to harmonize cleanup done on a skbuff on xmit path.
Before this patch, behaviors were different depending of the tunnel type.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This argument is not used, let's remove it.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This argument is not used, let's remove it.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script: (and a little typing)
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fengguang reported a compile warning:
drivers/net/vxlan.c: In function 'vxlan6_xmit_skb':
drivers/net/vxlan.c:1352:3: error: implicit declaration of function 'csum_ipv6_magic' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
this patch fixes it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the IPv6 version of "arp_reduce", ndisc_send_na()
will be needed.
Cc: David S. Miller <davem@davemloft.net>
Cc: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
route short circuit only has IPv4 part, this patch adds
the IPv6 part. nd_tbl will be needed.
Cc: David S. Miller <davem@davemloft.net>
Cc: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds IPv6 support to vxlan device, as the new version
RFC already mentions it:
http://tools.ietf.org/html/draft-mahalingam-dutt-dcops-vxlan-03
Cc: David Stevens <dlstevens@us.ibm.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch allows transmit side vlan offload for vxlan
devices.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than having static headroom calculation, adjust headroom
according to target device.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch allows more code sharing between vxlan and ovs-vxlan.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch adds data field to vxlan socket and export
vxlan handler api.
vh->data is required to store private data per vxlan handler.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once we have ovs-vxlan functionality, one UDP port can be assigned
to kernel-vxlan or ovs-vxlan port. Therefore following patch adds
vxlan demux functionality, so that vxlan or ovs module can
register for particular port.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use iptunnel_pull_header() for better code sharing.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restructure vxlan-socket management APIs so that it can be
shared between vxlan and ovs modules.
This patch does not change any functionality.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
v6-v7:
- get rid of zero refcnt vs from hashtable.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a regression introduced by:
commit fe5c3561e6
Author: stephen hemminger <stephen@networkplumber.org>
Date: Sat Jul 13 10:18:18 2013 -0700
vxlan: add necessary locking on device removal
The problem is that vxlan_dellink(), which is called with RTNL lock
held, tries to flush the workqueue synchronously, but apparently
igmp_join and igmp_leave work need to hold RTNL lock too, therefore we
have a soft lockup!
As suggested by Stephen, probably the flush_workqueue can just be
removed and let the normal refcounting work. The workqueue has a
reference to device and socket, therefore the cleanups should work
correctly.
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Tested-by: Cong Wang <amwang@redhat.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a regression introduced by:
commit 3fc2de2fab
Author: stephen hemminger <stephen@networkplumber.org>
Date: Thu Jul 18 08:40:15 2013 -0700
vxlan: fix igmp races
Before this commit, the old code was:
if (vxlan_group_used(vn, vxlan->default_dst.remote_ip))
ip_mc_join_group(sk, &mreq);
else
ip_mc_leave_group(sk, &mreq);
therefore we shoud check vxlan_group_used(), not its opposite,
for igmp_join.
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vxlan remote list is protected by RCU and guaranteed to be non-empty.
Split out the rcu and non-rcu access to the list to fix warning
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to replace an existing entry found in the
vxlan fdb database. The entry in question is identified
by its unicast mac address and the destination information
is changed. If the entry is not found, it is added in the
forwarding database. This is similar to changing an entry
in the neighbour table.
Multicast mac addresses can not be changed with the replace
option.
This is useful for virtual machine migration when the
destination of a target virtual machine changes. The replace
feature can be used instead of delete followed by add.
Resubmitted because net-next was closed last week.
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two race conditions in existing code for doing IGMP
management in workqueue in vxlan. First, the vxlan_group_used
function checks the list of vxlan's without any protection, and
it is possible for open followed by close to occur before the
igmp work queue runs.
To solve these move the check into vxlan_open/stop so it is
protected by RTNL. And split into two work structures so that
there is no racy reference to underlying device state.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix memory leaks and other badness from VXLAN network namespace
teardown. When network namespace is removed, all the vxlan devices should
be unregistered (not closed).
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The socket management is now done in workqueue (outside of RTNL)
and protected by vn->sock_lock. There were two possible bugs, first
the vxlan device was removed from the VNI hash table per socket without
holding lock. And there was a race when device is created and the workqueue
could run after deletion.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The zero MAC entry in the fdb is used as default destination. With
multiple default destinations it is possible to use vxlan in
environments that disable multicast on the infrastructure level, e.g.
public clouds.
Signed-off-by: Mike Rapoport <mike.rapoport@ravellosystems.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
When the last item is deleted from the remote destinations list, the
fdb entry is destroyed.
Signed-off-by: Mike Rapoport <mike.rapoport@ravellosystems.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
which will be reused by vxlan_fdb_delete
Signed-off-by: Mike Rapoport <mike.rapoport@ravellosystems.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
which will be reused by vxlan_fdb_delete
Signed-off-by: Mike Rapoport <mike.rapoport@ravellosystems.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Fix following sparse warnings.
drivers/net/vxlan.c:238:44: warning: incorrect type in argument 3 (different base types)
drivers/net/vxlan.c:238:44: expected restricted __be32 [usertype] value
drivers/net/vxlan.c:238:44: got unsigned int const [unsigned] [usertype] remote_vni
drivers/net/vxlan.c:1735:18: warning: incorrect type in initializer (different signedness)
drivers/net/vxlan.c:1735:18: expected int *id
drivers/net/vxlan.c:1735:18: got unsigned int static [toplevel] *<noident>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
For the notification code, a couple of places build fdb entries on
the stack, use structure initialization instead and fix formatting.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Based on initial work by Mike Rapoport <mike.rapoport@ravellosystems.com>
Use list macros and RCU for tracking multiple remotes.
Note: this code assumes list always has at least one entry,
because delete is not supported.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
The function vxlan_xmit_one always returns NETDEV_TX_OK, so there
is no point in keeping track of return values etc.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Put destruction of per-cpu statistics removal in
ndo_uninit since it is created by ndo_init.
This also avoids any problems that might be cause by destructor
being called after module removed.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
It is possible for two cpu's to race creating vxlan device.
For most cases this is harmless, but the ability to assign "next
avaliable vxlan device" relies on rtnl lock being held across the
whole operation. Therfore two instances of calling:
ip li add vxlan%d vxlan ...
could collide and create two devices with same name.
To fix this defer creation of socket to a work queue, and
handle possible races there. Introduce a lock to ensure that
changes to vxlan socket hash list is SMP safe.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Do join/leave from work queue to avoid lock inversion problems
between normal socket and RTNL. The code comes out cleaner
as well.
Uses Cong Wang's suggestion to turn refcnt into a real atomic
since now need to handle case where last use of socket is IGMP
worker.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Switch to using a per module work queue so that all the socket
deletion callbacks are done when module is removed.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
If vxlan is removed with active vxlan's it would crash because
rtnl_link_unregister (which calls vxlan_dellink), was invoked
before unregister_pernet_device (which calls vxlan_stop).
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Refactor various ip tunnels xmit functions and extend iptunnel_xmit()
so that there is more code sharing.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The check introduced by:
commit 26a41ae604
Author: stephen hemminger <stephen@networkplumber.org>
Date: Mon Jun 17 12:09:58 2013 -0700
vxlan: only migrate dynamic FDB entries
was not correct because it is checking flag about type of FDB
entry, rather than the state (dynamic versus static). The confusion
arises because vxlan is reusing values from bridge, and bridge is
reusing values from neighbour table, and easy to get lost in translation.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_clone fails if out of memory then just skip the fanout.
Problem was introduced in 3.10 with:
commit 6681712d67
Author: David Stevens <dlstevens@us.ibm.com>
Date: Fri Mar 15 04:35:51 2013 +0000
vxlan: generalize forwarding tables
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only migrate dynamic forwarding table entries, don't modify
static entries. If packet received from incorrect source IP address
assume it is an imposter and drop it.
This patch applies only to -net, a different patch would be needed for earlier
kernels since the NTF_SELF flag was introduced with 3.10.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for a packet to arrive during vxlan_stop(), and
have a dynamic entry created. Close this by checking if device
is up.
CPU1 CPU2
vxlan_stop
vxlan_flush
hash_lock acquired
vxlan_encap_recv
vxlan_snoop
waiting for hash_lock
hash_lock relased
vxlan_flush done
hash_lock acquired
vxlan_fdb_create
This is a day-one bug in vxlan goes back to 3.7.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When vxlan is compiled as builtin, its init code
runs before IPv6 init, this could cause problems
if we create IPv6 socket in the latter patch.
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'unsigned int' is slightly better.
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge net into net-next because some upcoming net-next changes
build on top of bug fixes that went into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some instances where vxlan fdb 'used' field is not updated after the entry
is used.
v2: rename vxlan_find_mac() as __vxlan_find_mac() and create a new vxlan_find_mac()
that also updates ->used field.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 823aa873bc
Author: stephen hemminger <stephen@networkplumber.org>
Date: Sat Apr 27 11:31:57 2013 +0000
vxlan: allow choosing destination port per vxlan
introduced per-vxlan UDP port configuration but only did half of the
necessary work. It added per vxlan destination for sending, but
overlooked the handling of multiple ports for incoming traffic.
This patch changes the listening port management to handle multiple
incoming UDP ports. The earlier per-namespace structure is now a hash
list per namespace.
It is also now possible to define the same virtual network id
but with different UDP port values which can be useful for migration.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since SKB_GSO_* flags are set by appropriate gso_segment callback
in TCP/UDP layer.
CC: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow configuring the default destination port on a per-device basis.
Adds new netlink paramater IFLA_VXLAN_PORT to allow setting destination
port when creating new vxlan.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than computing source port and returning it in host order
then swapping later, go ahead and compute it in network order to
start with. Cleaner and less error prone.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Source compatiability for build iproute2 was broken by:
commit c7995c43fa
Author: Atzm Watanabe <atzm@stratosphere.co.jp>
vxlan: Allow setting destination to unicast address.
Since this commit has not made it upstream (still net-next),
and better to avoid gratitious changes to exported API's;
go back to original definition, and add a comment.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NDA_PORT attribute was added, but the author wasn't careful
about width (port is 16 bits), or byte order. The attribute was
being dumped as 16 bits, but only 32 bit value would be accepted
when setting up a device. Also, the remote port is in network
byte order and was being compared with default port in host byte
order.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default port for VXLAN is not same as IANA value.
Document this.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow L2 redirection when VXLAN L3 switching is enabled
This patch restricts L3 switching to destination MAC addresses that are
marked as routers in order to allow virtual IP appliances that do L2
redirection to function with VXLAN L3 switching enabled.
We use L3 switching on VXLAN networks to avoid extra hops when the nominal
router for cross-subnet traffic for a VM is remote and the ultimate
destination may be local, or closer to the local node. Currently, the
destination IP address takes precedence over the MAC address in all cases.
Some network appliances receive packets for a virtualized IP address and
redirect by changing the destination MAC address (only) to be the final
destination for packet processing. VXLAN tunnel endpoints with L3 switching
enabled may then overwrite this destination MAC address based on the packet IP
address, resulting in potential loops and, at least, breaking L2 redirections
that travel through tunnel endpoints.
This patch limits L3 switching to the intended case where the original
destination MAC address is a next-hop router and relies on the destination
MAC address for all other cases, thus allowing L2 redirection and L3 switching
to coexist peacefully.
Signed-Off-By: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows setting VXLAN destination to unicast address.
It allows that VXLAN can be used as peer-to-peer tunnel without
multicast.
v4: generalize struct vxlan_dev, "gaddr" is replaced with vxlan_rdst.
"GROUP" attribute is replaced with "REMOTE".
they are based by David Stevens's comments.
v3: move a new attribute REMOTE into the last of an enum list
based by Stephen Hemminger's comments.
v2: use a new attribute REMOTE instead of GROUP based by
Cong Wang's comments.
Signed-off-by: Atzm Watanabe <atzm@stratosphere.co.jp>
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The multicast and broadcast packets may have RTCF_LOCAL set in rt_flags
and therefore will be sent out bypassing encapsulation. This breaks
delivery of packets sent to the vxlan multicast group.
Disabling encapsulation bypass for multicasts and broadcasts fixes the
issue.
Signed-off-by: Mike Rapoport <mike.rapoport@ravellosystems.com>
Tested-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Sridhar Samudrala <sri@us.ibm.com>
Tested-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently "bridge fdb show dev vxlan0" lists loopback address as
"1.0.0.127". Using htonl(INADDR_LOOPBACK) rather than passing it
directly to vxlan_snoop fixes the problem.
Signed-off-by: Mike Rapoport <mike.rapoport@ravellosystems.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes following warning:
drivers/net/vxlan.c:406:6: warning: symbol 'vxlan_fdb_free' was not declared. Should it be static?
drivers/net/vxlan.c:1111:37: warning: Using plain integer as NULL pointer
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch bypasses vxlan encapsulation if the destination vxlan
endpoint is a local device.
Changes since v1: added missing check for vxlan_find_vni() failure
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes following warning:-
drivers/net/vxlan.c:471:35: warning: symbol 'dev' shadows an earlier one
drivers/net/vxlan.c:433:26: originally declared here
drivers/net/vxlan.c:794:34: warning: symbol 'vxlan' shadows an earlier one
drivers/net/vxlan.c:757:26: originally declared here
CC: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use common ecn_encap functions from ip_tunnel module.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes bug in VXLAN code where is iptunnel_xmit() called with NULL
dev->tstats.
This bug was introduced in commit 6aed0c8bf7 (tunnel: use
iptunnel_xmit() again).
Following patch fixes bug by setting dev->tstats. It uses ip_tunnel
module code to share stats function.
CC: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch refactors GRE code into ip tunneling code and GRE
specific code. Common tunneling code is moved to ip_tunnel module.
ip_tunnel module is written as generic library which can be used
by different tunneling implementations.
ip_tunnel module contains following components:
- packet xmit and rcv generic code. xmit flow looks like
(gre_xmit/ipip_xmit)->ip_tunnel_xmit->ip_local_out.
- hash table of all devices.
- lookup for tunnel devices.
- control plane operations like device create, destroy, ioctl, netlink
operations code.
- registration for tunneling modules, like gre, ipip etc.
- define single pcpu_tstats dev->tstats.
- struct tnl_ptk_info added to pass parsed tunnel packet parameters.
ipip.h header is renamed to ip_tunnel.h
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch generalizes VXLAN forwarding table entries allowing an administrator
to:
1) specify multiple destinations for a given MAC
2) specify alternate vni's in the VXLAN header
3) specify alternate destination UDP ports
4) use multicast MAC addresses as fdb lookup keys
5) specify multicast destinations
6) specify the outgoing interface for forwarded packets
The combination allows configuration of more complex topologies using VXLAN
encapsulation.
Changes since v1: rebase to 3.9.0-rc2
Signed-Off-By: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/e1000e/netdev.c
Minor conflict in e1000e, a line that got fixed in 'net'
has been removed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
With recent patches from Pravin, most tunnels can't use iptunnel_xmit()
any more, due to ip_select_ident() and skb->ip_summed. But we can just
move these operations out of iptunnel_xmit(), so that tunnels can
use it again.
This by the way fixes a bug in vxlan (missing nf_reset()) for net-next.
Cc: Pravin B Shelar <pshelar@nicira.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable TSO for VXLAN devices and use UDP_TUNNEL to offload vxlan
segmentation.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following script will produce a kernel oops:
sudo ip netns add v
sudo ip netns exec v ip ad add 127.0.0.1/8 dev lo
sudo ip netns exec v ip link set lo up
sudo ip netns exec v ip ro add 224.0.0.0/4 dev lo
sudo ip netns exec v ip li add vxlan0 type vxlan id 42 group 239.1.1.1 dev lo
sudo ip netns exec v ip link set vxlan0 up
sudo ip netns del v
where inspect by gdb:
Program received signal SIGSEGV, Segmentation fault.
[Switching to Thread 107]
0xffffffffa0289e33 in ?? ()
(gdb) bt
#0 vxlan_leave_group (dev=0xffff88001bafa000) at drivers/net/vxlan.c:533
#1 vxlan_stop (dev=0xffff88001bafa000) at drivers/net/vxlan.c:1087
#2 0xffffffff812cc498 in __dev_close_many (head=head@entry=0xffff88001f2e7dc8) at net/core/dev.c:1299
#3 0xffffffff812cd920 in dev_close_many (head=head@entry=0xffff88001f2e7dc8) at net/core/dev.c:1335
#4 0xffffffff812cef31 in rollback_registered_many (head=head@entry=0xffff88001f2e7dc8) at net/core/dev.c:4851
#5 0xffffffff812cf040 in unregister_netdevice_many (head=head@entry=0xffff88001f2e7dc8) at net/core/dev.c:5752
#6 0xffffffff812cf1ba in default_device_exit_batch (net_list=0xffff88001f2e7e18) at net/core/dev.c:6170
#7 0xffffffff812cab27 in cleanup_net (work=<optimized out>) at net/core/net_namespace.c:302
#8 0xffffffff810540ef in process_one_work (worker=0xffff88001ba9ed40, work=0xffffffff8167d020) at kernel/workqueue.c:2157
#9 0xffffffff810549d0 in worker_thread (__worker=__worker@entry=0xffff88001ba9ed40) at kernel/workqueue.c:2276
#10 0xffffffff8105870c in kthread (_create=0xffff88001f2e5d68) at kernel/kthread.c:168
#11 <signal handler called>
#12 0x0000000000000000 in ?? ()
#13 0x0000000000000000 in ?? ()
(gdb) fr 0
#0 vxlan_leave_group (dev=0xffff88001bafa000) at drivers/net/vxlan.c:533
533 struct sock *sk = vn->sock->sk;
(gdb) l
528 static int vxlan_leave_group(struct net_device *dev)
529 {
530 struct vxlan_dev *vxlan = netdev_priv(dev);
531 struct vxlan_net *vn = net_generic(dev_net(dev), vxlan_net_id);
532 int err = 0;
533 struct sock *sk = vn->sock->sk;
534 struct ip_mreqn mreq = {
535 .imr_multiaddr.s_addr = vxlan->gaddr,
536 .imr_ifindex = vxlan->link,
537 };
(gdb) p vn->sock
$4 = (struct socket *) 0x0
The kernel calls `vxlan_exit_net` when deleting the netns before shutting down
vxlan interfaces. Later the removal of all vxlan interfaces, where `vn->sock`
is already gone causes the oops. so we should manually shutdown all interfaces
before deleting `vn->sock` as the patch does.
Signed-off-by: Zang MingJie <zealot0630@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should reset nf settings bond to the skb as ipip/ipgre do.
If not, the conntrack/nat info bond to the origin packet may continually
redirect the packet to vxlan interface causing a routing loop.
this is the scenario:
VETP VXLAN Gateway
/----\ /---------------\
| | | |
| vx+--+vx --NAT-> eth0+--> Internet
| | | |
\----/ \---------------/
when there are any packet coming from internet to the vetp, there will be lots
of garbage packets coming out the gateway's vxlan interface, but none actually
sent to the physical interface, because they are redirected back to the vxlan
interface in the postrouting chain of NAT rule, and dmesg complains:
Mar 1 21:52:53 debian kernel: [ 8802.997699] Dead loop on virtual device vxlan0, fix it urgently!
Mar 1 21:52:54 debian kernel: [ 8804.004907] Dead loop on virtual device vxlan0, fix it urgently!
Mar 1 21:52:55 debian kernel: [ 8805.012189] Dead loop on virtual device vxlan0, fix it urgently!
Mar 1 21:52:56 debian kernel: [ 8806.020593] Dead loop on virtual device vxlan0, fix it urgently!
the patch should fix the problem
Signed-off-by: Zang MingJie <zealot0630@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm not sure why, but the hlist for each entry iterators were conceived
list_for_each_entry(pos, head, member)
The hlist ones were greedy and wanted an extra parameter:
hlist_for_each_entry(tpos, pos, head, member)
Why did they need an extra pos parameter? I'm not quite sure. Not only
they don't really need it, it also prevents the iterator from looking
exactly like the list iterator, which is unfortunate.
Besides the semantic patch, there was some manual work required:
- Fix up the actual hlist iterators in linux/list.h
- Fix up the declaration of other iterators based on the hlist ones.
- A very small amount of places were using the 'node' parameter, this
was modified to use 'obj->member' instead.
- Coccinelle didn't handle the hlist_for_each_entry_safe iterator
properly, so those had to be fixed up manually.
The semantic patch which is mostly the work of Peter Senna Tschudin is here:
@@
iterator name hlist_for_each_entry, hlist_for_each_entry_continue, hlist_for_each_entry_from, hlist_for_each_entry_rcu, hlist_for_each_entry_rcu_bh, hlist_for_each_entry_continue_rcu_bh, for_each_busy_worker, ax25_uid_for_each, ax25_for_each, inet_bind_bucket_for_each, sctp_for_each_hentry, sk_for_each, sk_for_each_rcu, sk_for_each_from, sk_for_each_safe, sk_for_each_bound, hlist_for_each_entry_safe, hlist_for_each_entry_continue_rcu, nr_neigh_for_each, nr_neigh_for_each_safe, nr_node_for_each, nr_node_for_each_safe, for_each_gfn_indirect_valid_sp, for_each_gfn_sp, for_each_host;
type T;
expression a,c,d,e;
identifier b;
statement S;
@@
-T b;
<+... when != b
(
hlist_for_each_entry(a,
- b,
c, d) S
|
hlist_for_each_entry_continue(a,
- b,
c) S
|
hlist_for_each_entry_from(a,
- b,
c) S
|
hlist_for_each_entry_rcu(a,
- b,
c, d) S
|
hlist_for_each_entry_rcu_bh(a,
- b,
c, d) S
|
hlist_for_each_entry_continue_rcu_bh(a,
- b,
c) S
|
for_each_busy_worker(a, c,
- b,
d) S
|
ax25_uid_for_each(a,
- b,
c) S
|
ax25_for_each(a,
- b,
c) S
|
inet_bind_bucket_for_each(a,
- b,
c) S
|
sctp_for_each_hentry(a,
- b,
c) S
|
sk_for_each(a,
- b,
c) S
|
sk_for_each_rcu(a,
- b,
c) S
|
sk_for_each_from
-(a, b)
+(a)
S
+ sk_for_each_from(a) S
|
sk_for_each_safe(a,
- b,
c, d) S
|
sk_for_each_bound(a,
- b,
c) S
|
hlist_for_each_entry_safe(a,
- b,
c, d, e) S
|
hlist_for_each_entry_continue_rcu(a,
- b,
c) S
|
nr_neigh_for_each(a,
- b,
c) S
|
nr_neigh_for_each_safe(a,
- b,
c, d) S
|
nr_node_for_each(a,
- b,
c) S
|
nr_node_for_each_safe(a,
- b,
c, d) S
|
- for_each_gfn_sp(a, c, d, b) S
+ for_each_gfn_sp(a, c, d) S
|
- for_each_gfn_indirect_valid_sp(a, c, d, b) S
+ for_each_gfn_indirect_valid_sp(a, c, d) S
|
for_each_host(a,
- b,
c) S
|
for_each_host_safe(a,
- b,
c, d) S
|
for_each_mesh_entry(a,
- b,
c, d) S
)
...+>
[akpm@linux-foundation.org: drop bogus change from net/ipv4/raw.c]
[akpm@linux-foundation.org: drop bogus hunk from net/ipv6/raw.c]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foudnation.org: redo intrusive kvm changes]
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tunnel_ip_select_ident() is more efficient when generating ip-header
id given inner packet is of ipv4 type.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a user adds bridge neighbors, allow him to specify VLAN id.
If the VLAN id is not specified, the neighbor will be added
for VLANs currently in the ports filter list. If no VLANs are
configured on the port, we use vlan 0 and only add 1 entry.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VXLAN pseudo-device doesn't care if the mac address changes
when device is up.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The socket calls from vxlan to join/leave multicast group aren't
using the index of the underlying device, as a result the stack uses
the first interface that is up. This results in vxlan being non functional
over a device which isn't the 1st to be up.
Fix this by providing the iflink field to the vxlan instance
to the multicast calls.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds capability in vxlan to identify received
checksummed inner packets and signal them to the upper layers of
the stack. The driver needs to set the skb->encapsulation bit
and also set the skb->ip_summed to CHECKSUM_UNNECESSARY.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow VXLAN to make use of Tx checksum offloading and Tx scatter-gather.
The advantage to these two changes is that it also allows the VXLAN to
make use of GSO.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides extensions to VXLAN for supporting Distributed
Overlay Virtual Ethernet (DOVE) networks. The patch includes:
+ a dove flag per VXLAN device to enable DOVE extensions
+ ARP reduction, whereby a bridge-connected VXLAN tunnel endpoint
answers ARP requests from the local bridge on behalf of
remote DOVE clients
+ route short-circuiting (aka L3 switching). Known destination IP
addresses use the corresponding destination MAC address for
switching rather than going to a (possibly remote) router first.
+ netlink notification messages for forwarding table and L3 switching
misses
Changes since v2
- combined bools into "u32 flags"
- replaced loop with !is_zero_ether_addr()
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes addrexceeded member from vxlan_dev struct as it is unused.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__IPTUNNEL_XMIT() is an ugly macro, convert it to a static
inline function, so make it more readable.
IPTUNNEL_XMIT() is unused, just remove it.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the event of a VXLAN device being linked to a device that has a
hard_header_len greater than that of standard ethernet we could end up with
the hard_header_len not being large enough for outgoing frames. In order to
prevent this we should update the length when a lowerdev is provided.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eXtensible and not eXtensiable in the comment on top.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change fixes an issue I found where VXLAN frames were fragmented when
they were up to the VXLAN MTU size. I root caused the issue to the fact that
the headroom was 4 + 20 + 8 + 8. This math doesn't appear to be correct
because we are not inserting a VLAN header, but instead a 2nd Ethernet header.
As such the math for the overhead should be 20 + 8 + 8 + 14 to account for the
extra headers that are inserted for VXLAN.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
"ip link add ... type vxlan ... ttl X" allows a user to set the TTL
used by a VXLAN for encapsulation. The provided value was ignored by
vxlan module and the default value of 1 was used when encapsulating
multicast packets.
Signed-off-by: Vincent Bernat <bernat@luffy.cx>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VXLAN confused flag versus bitmap on state.
Based on part of a earlier patch by David Stevens.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If vxlan is created and the ifindex is passed; there are two cases which
are incorrectly handled by the existing code. The ifindex could be zero
(i.e. no device) or there could be no device with that ifindex.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vxlan was trying to use postpull_rcsum to allow receive checksum
offload to work on drivers using CHECKSUM_COMPLETE method. But this
doesn't work correctly. Just force full receive checksum on received
packet.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tell upper layer protocols to allocate skb with additional headroom.
This avoids allocation and copy in local packet sends.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VXLAN bases source UDP port based on flow to help the
receiver to be able to load balance based on outer header flow.
This patch restricts the port range to the normal UDP local
ports, and allows overriding via configuration.
It also uses jhash of Ethernet header when looking at flows
with out know L3 header.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tunnelling a skb, associate it with the tunnel socket.
This allows parameters set on tunnel socket (like multicast loop
flag), to be picked up by ip_output.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Select source address for VXLAN packet based on route destination
and don't lie to route code. VXLAN is not GRE.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shift was wrong direction causing packets to hash based on
other parts of the ethernet header, not the address.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move code to find destination to a small function.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a couple harmless sparse warnings reported by Fengguang Wu.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove including <linux/version.h> that don't need it.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move vxlan UDP socket to correct network namespace
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an implementation of Virtual eXtensible Local Area Network
as described in draft RFC:
http://tools.ietf.org/html/draft-mahalingam-dutt-dcops-vxlan-02
The driver integrates a Virtual Tunnel Endpoint (VTEP) functionality
that learns MAC to IP address mapping.
This implementation has not been tested only against the Linux
userspace implementation using TAP, not against other vendor's
equipment.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
