The routine to allocate a cqp request is not called from process
context code. Since it is not OK to sleep, it needs to use GFP_ATOMIC
not GFP_KERNEL.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code currently has a work structure in the QP. This requires a
lock and a pending flag to ensure there is never more than one request
active. When two events happen quickly (such as FIN and LLP CLOSE),
it causes unnecessary timeouts since the second one is dropped.
This fix allocates memory for the work request so the second one can
be queued. A lock is removed since it is no longer needed.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During termination, it is possible for the refcnt to go to zero while
the worker thread is posting events upward. This fix increments the
refcnt before the request is passed to the worker thread. The thread
decrements the refcnt when the request is completed.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Userspace apps are supposed to release all ib device resources if they
receive a fatal async event (IBV_EVENT_DEVICE_FATAL). However, the
app has no way of knowing when the device has come back up, except to
repeatedly attempt ibv_open_device() until it succeeds.
However, currently there is no protection against the open succeeding
while the device is in being removed following the fatal event. In
this case, the open will succeed, but as a result the device waits in
the middle of its removal until the new app releases its resources --
and the new app will not do so, since the open succeeded at a point
following the fatal event generation.
This patch adds an "active" flag to the device. The active flag is set
to false (in the fatal event flow) before the "fatal" event is
generated, so any subsequent ibv_dev_open() call to the device will
fail until the device comes back up, thus preventing the above
deadlock.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the mthca driver uses the same name for interrupts for every
device in the system. This can make it very confusing trying to work
out exactly which device MSI-X interrupts are for. Change the driver
to add the PCI name of the device to the interrupt name.
Signed-off-by: Arputham Benjamin <abenjamin@sgi.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_ib_lock_cqs()/mthca_ib_unlock_cqs() are helper functions that
lock/unlock both CQs attached to a QP in the proper order to avoid
AB-BA deadlocks. Annotate this so sparse can understand what's going
on (and warn us if we misuse these functions).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_config_reg.h was including <asm/page.h> for no reason -- the whole
file is just defines of constants, so it's entirely self-contained.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Userspace apps are supposed to release all ib device resources if they
receive a fatal async event (IBV_EVENT_DEVICE_FATAL). However, the
app has no way of knowing when the device has come back up, except to
repeatedly attempt ibv_open_device() until it succeeds.
However, currently there is no protection against the open succeeding
while the device is in being removed following the fatal event. In
this case, the open will succeed, but as a result the device waits in
the middle of its removal until the new app releases its resources --
and the new app will not do so, since the open succeeded at a point
following the fatal event generation.
This patch adds an "active" flag to the device. The active flag is set
to false (in the fatal event flow) before the "fatal" event is
generated, so any subsequent ibv_dev_open() call to the device will
fail until the device comes back up, thus preventing the above
deadlock.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mlx4_ib_lock_cqs()/mlx4_ib_unlock_cqs() are helper functions that
lock/unlock both CQs attached to a QP in the proper order to avoid
AB-BA deadlocks. Annotate this so sparse can understand what's going
on (and warn us if we misuse these functions).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
dev->ibdev.iwcm allocation may fail, prevent a dereference.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since the original commit 883a99c7 ("[IB] uverbs: Add a mask of device
methods allowed for userspace"), the uverbs core returns EINVAL for
commands not implemented by a specific low-level driver.
This creates a problem that there is no way to tell the difference
between an unimplemented command and an implemented one which is
incorrectly invoked (which also returns EINVAL).
The fix is to have unimplemented commands return ENOSYS.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Until now, retries were only sent when joining a multicast group. This
patch will adds retries when leaving a multicast group as well.
Signed-off-by: Ron Livne <ronli@voltaire.com>
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Replace open-coded reimplementations with printk_once().
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use the %pM conversion specifier to print a MAC address.
Signed-off-by: Tobias Klauser <klto@zhaw.ch>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rather than just defining static spinlock_t variables and then
initializing them later in init functions, simply define them with
DEFINE_SPINLOCK() and remove the calls to spin_lock_init(). This cleans
up the source a tad and also shrinks the compiled code; eg on x86-64:
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-40 (-40)
function old new delta
ib_uverbs_init 336 326 -10
ib_mad_init_module 147 137 -10
ib_sa_init 123 103 -20
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The hop count field in a directed route MAD is only allowed to be in the
range 0 to 63 (by spec). Check that this really is the case to avoid
accessing outside the bounds of the hop array.
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Check that the format of multicast link addresses is correct before
taking them from dev->mc_list to priv->multicast_list. This way we
never try to send a bogus address to the SA, which prevents badness
from erronous 'ip maddr addr add', broken bonding drivers, etc.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
IPoIB currently must use irqsave locking for priv->lock, since it is
taken from interrupt context in one path. However, ipoib_send() does
skb_orphan(), and the network stack locking is not IRQ-safe.
Therefore we need to make sure we don't hold priv->lock when calling
ipoib_send() to avoid lockdep warnings (the code was almost certainly
safe in practice, since the only code path that takes priv->lock from
interrupt context would never call into the network stack).
Addresses: http://bugzilla.kernel.org/show_bug.cgi?id=13757
Reported-by: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
strlcpy() will always null terminate the string. node_desc is not
guaranteed to be NUL-terminated so just use memcpy().
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The driver was reporting CQE flags in the wrong bit positions, causing
consumers to miss incoming immediate data.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The old code used a lot of hard-coded values, which might not be valid
in all environments (especially routed fabrics or partitioned
subnets). Copy as much information as possible from the incoming
request to correct that.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make port autodetect mode the default for the ehca driver. The
autodetect code has been in the kernel for several releases now and
has proved to be stable.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A close/abort while waiting for a wr_ack during connection migration
can cause a hung process in iwch_accept_cr/iwch_reject_cr.
The fix is to set rpl_error/rpl_done and wake up the waiters when we
get a close/abort while in MPA_REQ_RCVD state.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Keep ref on connection request endpoints until either accepted or
rejected so it doesn't get freed early.
- Endpoint flags now need to be set via atomic bitops because they can
be set on both the iw_cxgb3 workqueue thread and user disconnect
threads.
- Don't move out of CLOSING too early due to multiple calls to
iwch_ep_disconnect.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Massage the err_handler upcall into an event handler upcall, pass
netdev port events to the cxgb3 ULPs and generate RDMA port events
based on LLD port events.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Neil Horman <nhorman@txudriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to put ethtool_ops in data, they should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __init and __exit annotations to the module_init/module_exit
functions from drivers/infiniband/core/addr.c and cma.c.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Increment version number for DMEM toleration.
Signed-off-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
dma_sync_single() is deprecated now, and the use in mthca is wrong:
there should be a dma_sync_single_for_cpu() before touching the memory
from the CPU, and a dma_sync_single_for_device() afterwards. Fix
this, prompted by a kick in the pants from a patch from FUJITA
Tomonori <fujita.tomonori@lab.ntt.co.jp>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During cluster testing, one QP was not closed, as FIN is not handled
properly when its rexmit count expires or in some cases when RST is is
received after sending FIN. The reason is that the cm_id does not get
decremented under these conditions.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In nes_query_device(), max_qp_init_rd_atom is incorrectly set to
max_qp_wr. This was found when a test application had a dapl async
event error.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This prevents the memcpy() of a guid_entries element using a negative index.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Implement toleration of dynamic memory operations and 16 GB gigantic
pages, where "toleration" means that the driver can cope with dynamic
memory operations that happen before the driver is loaded. While the
ehca driver is loaded, dynamic memory operations are still prohibited
by returning NOTIFY_BAD from the memory notifier.
On module load the driver walks through available system memory,
checks for available memory ranges and then registers the kernel
internal memory region accordingly. The translation of address ranges
is implemented via a 3-level busmap.
Signed-off-by: Hannes Hering <hering2@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: general@lists.openfabrics.org
Cc: Christoph Raisch <raisch@de.ibm.com>
Acked-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: general@lists.openfabrics.org
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Don't double-free IRQs when falling back from MSI-X to INTx
IB/mthca: Don't double-free IRQs when falling back from MSI-X to INTx
IB/mlx4: Add strong ordering to local inval and fast reg work requests
IB/ehca: Remove superfluous bitmasks from QP control block
RDMA/cxgb3: Limit fast register size based on T3 limitations
RDMA/cxgb3: Report correct port state and MTU
mlx4_core: Add module parameter for number of MTTs per segment
IB/mthca: Add module parameter for number of MTTs per segment
RDMA/nes: Fix off-by-one bugs in reset_adapter_ne020() and init_serdes()
infiniband: Remove void casts
IB/ehca: Increment version number
IB/ehca: Remove unnecessary memory operations for userspace queue pairs
IB/ehca: Fall back to vmalloc() for big allocations
IB/ehca: Replace vmalloc() with kmalloc() for queue allocation
When both MSI-X and legacy INTx fail to generate an interrupt, the
driver frees the MSI-X interrupts twice. Fix this by clearing the
have_irq flag for the MSI-X interrupts when they are freed the first
time.
Reported-by: Yinghai Lu <yhlu.kernel@gmail.com>
Tested-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The ConnectX Programmer's Reference Manual states that the "SO" bit
must be set when posting Fast Register and Local Invalidate send work
requests. When this bit is set, the work request will be executed
only after all previous work requests on the send queue have been
executed. (If the bit is not set, Fast Register and Local Invalidate
WQEs may begin execution too early, which violates the defined
semantics for these operations)
This fixes the issue with NFS/RDMA reported in
<http://lists.openfabrics.org/pipermail/general/2009-April/059253.html>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
All the fields in the control block are nicely right-aligned, so no
masking is necessary.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last two drivers that need skb->dst in their start_xmit() function
Tell dev_hard_start_xmit() to no release it by unsetting IFF_XMIT_DST_RELEASE
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T3 firmware only supports one WRs worth of page list for fast register
work requests. The driver currently allows 2 WRs worth, which
doesn't work for T3, so reduce the limit in the driver.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current MTT allocator uses kmalloc() to allocate a buffer for its
buddy allocator, and thus is limited in the amount of MTT segments
that it can control. As a result, the size of memory that can be
registered is limited too. This patch uses a module parameter to
control the number of MTT entries that each segment represents,
allowing more memory to be registered with the same number of
segments.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a task did not complete normally due to a TMF, libiscsi will
now complete the task with the state ISCSI_TASK_ABRT_TMF. Drivers
like bnx2i that need to free resources if a command did not complete normally
can then check the task state. If a driver does not need to send
a special command if we have dropped the session then they can check
for ISCSI_TASK_ABRT_SESS_RECOV.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When we create the tcp/ip connection by calling ep_connect, we currently
just go by the routing table info.
I think there are two problems with this.
1. Some drivers do not have access to a routing table. Some drivers like
qla4xxx do not even know about other ports.
2. If you have two initiator ports on the same subnet, the user may have
set things up so that session1 was supposed to be run through port1. and
session2 was supposed to be run through port2. It looks like we could
end with both sessions going through one of the ports.
Fixes for cxgb3i from Karen Xie.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Network device sysfs files that grab the rtnl_lock unconditionally
will deadlock if accessed when the network device is being
unregistered. So use trylock and syscall_restart to avoid this
deadlock.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With a postfix increment, i is incremented one past 10K/5K before the
loop ends, so the error messages will be displayed too soon if the
test succeeds on the last iteration. Fix the comparisons to be >
instead of >=.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The queue map for flush completion circumvention is only used for
kernel space queue pairs. This patch skips the allocation of the
queue maps in case the QP is created for userspace. In addition, this
patch does not iomap the galpas for kernel usage if the queue pair is
only used in userspace. These changes will improve the performance of
creation of userspace queue pairs.
Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In case of large queue pairs there is the possibillity of allocation
failures due to memory fragmentation when using kmalloc(). To ensure
the memory is allocated even if kmalloc() can not find chunks which
are big enough, we fall back to allocating the memory with vmalloc().
Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
To improve performance of driver resource allocation, replace
vmalloc() calls with kmalloc().
Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Don't overwrite fast registration page list when posting work request
RDMA/cxgb3: Don't complete flushed send work requests twice
The low-level mlx4 driver modified the page-list addresses for fast
register work requests post send to big-endian, and set a "present"
bit. This caused problems later when the consumer attempted to unmap
the pages using the page-list (using the list addresses which were
assumed to be still in CPU-endian order). Fix the mlx4 driver to
allocate two buffers and use a private buffer for the hardware-format
bus addresses.
This patch fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1571>,
an NFS/RDMA server crash. The cause of the crash was found by Vu Pham
of Mellanox. The fix is along the lines suggested by Steve Wise in
comment #21 in bug 1571.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the SQ is flushed, mark the flushed entries as not signaled so
the poll logic doesn't re-insert the CQ entry thinking its an out of
order completion.
The bug can cause the NFS/RDMA server to crash due to processing the
same completed work request twice.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If reg_phys_mem() fails, we need to free memory allocated for MPA
frame with private data before returning the error. Also move
nes_add_ref() after the reg_phys_mem() is successful.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Running large cluster setup, we are hanging after many hours of
testing. Fixing this required going over the code and making sure the
rexmit entry was properly removed based on the cm_node's state and
packet received. Also when receiving a FIN packet, check seq# and
make sure there were no errors before calling handle_fin().
Following are the changes done in nes_cm.c:
* handle_ack_pkt() needs to return error value, so in case of error,
handle_fin() is not called. Some cleanup done while going over the code.
* handle_rst_pkt(), handling of cm_node's NES_CM_STATE_LAST_ACK is missing.
* process_packet(), in case of FIN only packet is received, call
check_seq() before processing.
* in handle_fin_pkt(), we are calling cleanup_retrans_entry() for all
conditions, even if the packets need to be dropped.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Under heavy load with large cluster testing, it may take longer to
receive a response to MPA requests. Change the driver to wait longer
after each rexmit to max time value.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
check_seq() was not checking if the seq#s have wrapped. Fix it.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a connect request comes, apbvt should only be set for
non-loopback connections.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove the NES_DEBUG that is causing the compile warning about an
unused variable when INFINIBAND_NES_DEBUG is not enabled.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
/sys/class/infiniband/nes?/fw_ver is not displaying firmware version
properly (it shows 0.0.0 with the current code). Fill in the correct
firmware version number.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
With updated PHY firmware for SFP_D, setting the trace length to 1
inch for SFP_D provides a more stable link.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enable repause timer for port 1. Without this setting, under stress,
the chip may misbehave.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In commit 1b949324 ("RDMA/nes: Fix SFP+ PHY initialization") there is
a mistake in the clean up code that removed port 1 CDR loop filter
settings for 10G cards other than CX4. Put the correct setting back
for appropriate PHY types.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change thermo mitigation code to flip the SerDes1 reference clock to
internal, to match the change in commit a4849fc1 ("RDMA/nes: Add
wide_ppm_offset parm for switch compatibility").
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set target can queue limit to the number of preallocated
session tasks we have.
This along with the cxgb3i can_queue patch will fix a throughput
problem where it could only queue one LU worth of data at a time.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In error paths where a CQ is not created, pbl is not freeed properly.
In nes_destroy_cq(), add the corresponding check for nescq->mcrqf to
not call nes_free_resource() when it is already done in nes_create_cq().
Signed-off-by: Miroslaw Walukiewicz <miroslaw.walukiewicz@intel.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commands INIT_HCA, CLOSE_HCA, SYS_EN, SYS_DIS, and CLOSE_IB all have 1
second timeouts. For INIT_HCA this causes problems when had more than
2^18 are QPs configured, since the command takes more than 1 second to
complete.
All other commands have 60-second timeouts. This patch makes the
above commands consistent with the rest of the commands (and with the
chip documentation).
This patch is an expansion of a patch from Arthur Kepner
<akepner@sgi.com> fixing just the INIT_HCA timeout.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
QP attributes must stay initialized when moving back to IDLE. Zeroing
them will crash the system in _flush_qp() if the QP is subsequently
moved to ERROR and back to IDLE.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code incorrectly failed memory registration if the buffer was not
page aligned. Also, the length field is mangled causing the hardware
to think the registration is much larger than it really is.
The fix is to remove the page alignment restriction as well the
incorrect length adjustment. Also make sure that all buffers after
the first start at a page boundary, and all buffers except the last
end on a page boundary.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Initialize pbl_count_256 to 0 to get rid of the warning:
drivers/infiniband/hw/nes/nes_verbs.c: In function 'nes_reg_mr':
drivers/infiniband/hw/nes/nes_verbs.c:1955: warning: 'pbl_count_256' may be used uninitialized in this function
Reported-by: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If NAPI is enabled while IPoIB's CQ is being drained, it creates a
race on priv->ibwc between ipoib_poll() and ipoib_drain_cq(), leading
to memory corruption.
The solution is to enable/disable NAPI in ipoib_ib_dev_{open/stop}()
instead of in ipoib_{open/stop}(), and sync NAPI on the INITIALIZED
flag instead on the ADMIN_UP flag. This way NAPI will be disabled when
ipoib_drain_cq() is called.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1587>.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
NFS/RDMA currently fails to set up connections if peer2peer is on.
This is due to the fact that the NFS/RDMA client sets its ORD to 0.
If peer2peer is set, make sure the active side ORD is >= 1 and the
passive side IRD is >=1.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Add support for new SFP+ PHY
RDMA/nes: Add wide_ppm_offset parm for switch compatibility
RDMA/nes: Fix SFP+ PHY initialization
RDMA/nes: Fix nes_nic_cm_xmit() error handling
RDMA/nes: Fix error handling issues
RDMA/nes: Fix incorrect casts on 32-bit architectures
IPoIB: Document newish features
RDMA/cma: Create cm id even when IB port is down
RDMA/cma: Use rate from IPoIB broadcast when joining IPoIB multicast groups
IPoIB: Avoid free_netdev() BUG when destroying a child interface
mlx4_core: Don't leak mailbox for SET_PORT on Ethernet ports
RDMA/cxgb3: Release dependent resources only when endpoint memory is freed.
RDMA/cxgb3: Handle EEH events
IB/mlx4: Use pgprot_writecombine() for BlueFlame pages
Add new register settings for new SFP+ PHY/firmware.
Add new PHY to to nes_netdev_get/set_settings.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We have observed unstable link with a new BNT switch.
Add wide_ppm_offset parameter to allow the user to control the clock
ppm offset on the CX4 interface for better compatibility. Default is
100ppm, setting it to 1 will increase it to 300ppm. Change default
SerDes1 reference clock to external source.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
SFP+ PHY initialization has very long delays, incorrect settings for
direct attach copper cables, and inconsistent link detection.
Adjust delays to the minimum required by the PHY. Worst case is now
less than 4 seconds. Add new register settings for direct attach
cables. Change link detection logic to use two new registers for more
consistent link state detection. Reorganize code to shorten line
length.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We are getting crash or hung situation when we are running network
cable pull tests during RDMA traffic.
In schedule_nes_timer(), we return an error if nes_nic_cm_xmit()
returns failure. This is changed to success as skb is being put on
the timer routines to be processed later. In send_syn() case, we are
indicating connect failure once from nes_connect() and the other when
the rexmit retries expires.
The other issue is skb->users which we are incrementing before calling
nes_nic_cm_xmit() which calls dev_queue_xmit() but in case of failure
we are decrementing the skb->users at the same time putting the skb on
the rexmit path. Even if dev_queue_xmit() fails, the skb->users is
decremented already. We are removing the decrement of skb->users in
case of failure from both schedule_nes_timer() as well as from
nes_cm_timer_tick().
There is also extra check in nes_cm_timer_tick() for rexmit failure
which does a break from the loop is removed. This causes problem as
the other nodes have their cm_node->ref_count incremented and are not
processed.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix issues found by static code analysis:
(1) Check if cm_node was successfully created for loopback connection.
(2) schedule_nes_timer() does not free up allocated memory after
encountering an error. There is a WARN_ON() for this condition.
(3) there is a cm_node->freed flag which is set but not used.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The were some incorrect casts to unsigned long that caused 64-bit values
to be truncated on 32-bit architectures and made the driver pass invalid
adresses and lengths to the hardware. The problems were primarily seen
with kernels with highmem configured but some could show up in
non-highmem kernels, too.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When doing rdma_resolve_addr(), if the relevant IB port is down, the
function fails and the cm_id is not bound to the correct device.
Therefore, application does not have a device handle and cannot wait
for the port to become active. The function fails because the
underlying IPoIB interface is not joined to the broadcast group and
therefore the SA does not have a multicast record to take a Q_Key
from.
The fix is to use lazy Q_Key resolution - cma_set_qkey() will set
id_priv->qkey if it was not set, and will be called just before the
Q_Key is really required.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>