The scqe.stag is actually __b32, fix it.
drivers/infiniband/hw/cxgb4/cq.c:754:52: warning: cast to restricted __be32
Cc: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Moni Shoua <monis@mellanox.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In recent code, two path record entries are alwasy cleared while
allocated could be either one or two path record entries.
This leads to zero out of unallocated memory.
This fix initializes alternative path record only when alternative path
is set.
While we are at it, path record allocation doesn't check for OPA
alternative path, but rest of the code checks for OPA alternative path.
Path record allocation code doesn't check for OPA alternative LID.
This can further lead to memory corruption when only one path record is
allocated, but there is actually alternative OPA path record present in CM
request.
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: 9fdca4da4d ("IB/SA: Split struct sa_path_rec based on IB and ROCE specific fields")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Some user space application would like to do RSS on the inner
packet fields instead on the outer.
When MLX5_RX_HASH_INNER is set with one or more of the other
hash fields, then the RSS will be done using the inner packet.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The device can support receive Stateless Offloads for the inner
packet's fields only when the packet is processed by TIR which is
enabled to support tunneling. Otherwise, the device treats the
packet as an ordinary non-tunneling packet and receive offloads
can be done only for the outer packet's field.
In order to enable receive Stateless Offloading support for incoming
tunneling traffic the TIR should be created with tunneled_offload_en.
Tunneling offloads is supported only be raw ethernet QP.
This patch includes:
* New QP creation flag for tunneling offloads.
* Reports device capabilities.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In some benchmarks and some CPU architectures, writing the CQE on a full
cache line size improves performance by saving memory access operations
(read-modify-write) relative to partial cache line change. This patch
lets the user to configure the device to pad the CQE up to 128B in case
its content is less than 128B. Currently the driver supports only padding
for a CQE size of 128B.
Signed-off-by: Guy Levi <guyle@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In commit 1cbe6fc86c ("IB/mlx5: Add support for CQE compressing") the
concept of CQE compression was introduced and added a support for 64B
CQE size. This change update the code to support 128B CQE size as well.
Signed-off-by: Guy Levi <guyle@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Allow creation of a multi-packet receive queue.
In order to create a multi-packet RQ, the following fields in
the mlx5_ib_rwq should be set:
- log_num_strides: Log of number of strides per WQE
- single_stride_log_num_of_bytes: Log of a single stride size
- two_byte_shift_en: When enabled, hardware pads 2 bytes of zeros
before writing the message to memory (e.g. for the IP alignment).
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch reports the device's striding RQ capabilities to
the user-space:
- min/max_single_stride_log_num_of_bytes: Log of min/max number of
bytes in a single stride.
- min/max_single_wqe_log_num_of_strides: Log of min/max number of
strides in a single WQE.
- supported_qpts: A bit mask to know which QP types support multi-
packet RQ, for now only Raw Packet QPs.
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
It is needed to call modify cq API for modifying cq
context fields for controlling event generation
moderations. This patch mainly adds it.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch updates the PD specification to 16M for hip08. And it
updates the numbers of mtt and cqe segments for the buddy.
As the CQE supports hop num 1 addressing, the CQE specification is
64k. This patch updates to set the CQE specification to 64k.
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
As the increase of the IRRL specification in hip08, the IRRL table
chunk size needs to be updated.
This patch updates the IRRL table chunk size to 256k for hip08.
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch updates to support WQE, CQE and PBL page size configurable
feature, which includes base address page size and buffer page size.
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
NAPI budget is 64 packets, while maximum polling size for
the send CQ is 16. Let's bring them in sync, so the NAPI
budget will be reused completely.
Cc: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Instead of explicit call to poll_cq of the tx ring, use the NAPI mechanism
to handle the completions of each packet that has been sent to the HW.
The next major changes were taken:
* The driver init completion function in the creation of the send CQ,
that function triggers the napi scheduling.
* The driver uses CQ for RX for both modes UD and CM, and CQ for TX
for CM and UD.
Cc: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The first step toward using NAPI in the UD/TX flow is to separate
between two flows, the NAPI and the xmit, meaning no use of shared
variables between both flows.
This patch takes out the tx_outstanding variable that was used in both
flows and instead the driver uses the 2 cyclic ring variables: tx_head
and tx_tail, tx_head used in the xmit flow and tx_tail in the NAPI flow.
Cc: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Make these structures const as they are either passed to the functions
having the argument as const or stored as a reference in the "ci_type"
const field of a config_item structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Out of order flow is not working for iWARP.
This patch got cut out from initial series that added out
of order support for iWARP.
Make out of order code common for iWARP and iSCSI.
Add new configuration option CONFIG_QED_OOO. Set by
qedr and qedi Kconfigs.
Fixes: d1abfd0b4e ("qed: Add iWARP out of order support")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Control QP (CQP) command backlog list is initialized at
device initialization time. It is not reinitialized in
the reset flow. Move the initialization to CQP creation
time so the list can be initialized correctly for reset as well.
Fixes: 86dbcd0f12 ("i40iw: add file to handle cqp calls")
Signed-off-by: Bob Sharp <Robert.O.Sharp@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If User-space Direct Access (UDA) QP creation fails,
the QP entry is not removed from QoS list. Fix this
by removing QP from QoS list if create QP fails.
Fixes: 0fc2dc5889 ("i40iw: Add Quality of Service support")
Signed-off-by: Ivan Barrera <ivan.d.barrera@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Clear Control Queue Pair (CQP) Head/Tail on CQP
initialization as during an adapter reset, these
values are not reinitialized. Tail is cleared by
writing 0 to CQP's tail register. Head is cleared
by writing 0 to CQP's doorbell register.
Fixes: 86dbcd0f12 ("i40iw: add file to handle cqp calls")
Signed-off-by: Christopher Bednarz <christopher.n.bednarz@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Queue depth calculations use a mix of work requests
and actual number of bytes. Consolidate all calculations
using minimum WQE size to avoid confusion.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
On a netdev MTU change event, the iWARP
Exception Queue (IEQ) buffers may not be
sized properly to handle the new MTU.
Reinitialize the IEQ with new MTU size on MTU
change event.
Also, add define for the max ethernet frame size
field in IEQ QP context instead of the snd_mss
define which is for iWARP QPs' MSS field.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Completion Event Queues are created and destroyed on
a per device basis as opposed to per User-space Direct
Access resource.
Move ceq_valid to the correct place in i40iw_sc_dev
from i40iw_puda_rsrc.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The IPv6 header size is not subtracted from MTU when MSS is
set for QPs.
Save MTU opposed to MSS in the vsi struct during
initialization and calculate the MSS based on IPv4 vs
IPv6 connection.
Fixes: f27b4746f3 ("i40iw: add connection management code")
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Some structures for post SQ operation are not used.
Remove the following:
i40iw_post_send_w_inv
i40iw_post_inline_send_w_inv
send_w_sol
send_w_inv
send_w_sol_inv
inline_send_w_sol
inline_send_w_inv
inline_send_w_sol_inv
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Consolidate exception_lan_queue under VSI structure
where it belongs. Remove it from device and QP structures.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The field static_rsrc in i40iw_create_qp_info is unused
and not needed. Remove it.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The AE source field in Asynchronous Event Queue Entry (AEQE) is
not set by the hardware for some AEs, but the code assumes it does.
This results in incorrect processing of some AEs.
Fix this by setting ae_src to I40IW_AE_SOURCE_RSVD for those AEs.
Fixes: 86dbcd0f12 ("i40iw: add file to handle cqp calls")
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Conflicts:
drivers/infiniband/hw/cxgb4/cm.c
drivers/infiniband/hw/qib/qib_driver.c
drivers/infiniband/hw/qib/qib_mad.c
There were minor fixups needed in these files. Just minor context diffs
due to patches from independent sources touching the same basic area.
Signed-off-by: Doug Ledford <dledford@redhat.com>
The early for-next branch was based on v4.14-rc2, while the shared pull
request I got from Mellanox used a v4.14-rc4 base. I'm making the
branch that was the shared Mellanox pull request the new for-next branch
and merging the early for-next branch into it.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Using the ARRAY_SIZE macro improves the readability of the code.
Found with Coccinelle with the following semantic patch:
@r depends on (org || report)@
type T;
T[] E;
position p;
@@
(
(sizeof(E)@p /sizeof(*E))
|
(sizeof(E)@p /sizeof(E[...]))
|
(sizeof(E)@p /sizeof(T))
)
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The IB/core provides address resolution service and invokes callback
handler when address resolve request completes of requester in worker
thread context.
Such caller might allocate or free memory in callback handler
depending on the completion status to make further progress or to
terminate a connection. Most ULPs resolve route which involves
allocating route entry and path record elements in callback event handler.
It has been noticed that WQ_MEM_RECLAIM flag should not be used for
workers that tend to allocate memory in this [1] thread discussion.
In order to mitigate this situation, WQ_MEM_RECLAIM flag was dropped for
other such WQs in this [2] patch.
Similar problem might arise with address resolution path, though its not
yet noticed. The ib_addr workqueue is not memory reclaim path due to its
nature of invoking callback that might allocate memory or don't free any
memory under memory pressure.
[1] https://www.spinics.net/lists/linux-rdma/msg53239.html
[2] https://www.spinics.net/lists/linux-rdma/msg53416.html
Fixes: f54816261c ("IB/addr: Remove deprecated create_singlethread_workqueue")
Fixes: 5fff41e1f8 ("IB/core: Fix race condition in resolving IP to MAC")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch fixes the case where 'lifespan' entry of the hw_counters
is not writable. Currently write callback is not exposed for for
the hw_counters sysfs operation. Due to this, modifying lifespan
value results into permission denied error in below example.
echo 10 > /sys/class/infiniband/mlx5_0/ports/1/hw_counters/lifespan
-bash: /sys/class/infiniband/mlx5_0/ports/1/hw_counters/lifespan:
Permission denied
This patch adds the hook to modify any attribute which implements
store() operation.
Fixes: b40f4757da ("IB/core: Make device counter infrastructure dynamic")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Since IB/core resolves the destination mac address for user and kernel
consumers, avoid resolving in multiple provider drivers.
Only ib_core resolves DMAC now, therefore resolve_eth_dmac is removed as
exported symbol.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Introduce rdma_create_user_ah API which allows passing udata to
provider driver and additionally which resolves DMAC for RoCE.
ib_resolve_eth_dmac() resolves destination mac address for unicast,
multicast, link local ipv4 mapped ipv6 and ipv6 destination gid entry.
This allows all RoCE provider drivers to avoid duplicating such code.
Such change brings consistency where IB core always resolves dmac and pass
it to RoCE provider drivers for user and kernel consumers, with this
ah_attr->roce.dmac is always an input field for provider drivers.
This uniformity avoids exporting ib_resolve_eth_dmac symbol to providers
or other modules. Therefore its removed as exported symbol at later in
the patch series.
Now uverbs and umad both makes use of rdma_create_user_ah API which
fixes the issue where umad has invalid DMAC for address.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Also removes an unused timer and
drops a redundant initialization.
Cc: Steve Wise <swise@chelsio.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
This includes the remaining timers missed in the earlier i40iw patch.
Cc: Faisal Latif <faisal.latif@intel.com>
Cc: Shiraz Saleem <shiraz.saleem@intel.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Also removes an unused timer.
Cc: Steve Wise <swise@chelsio.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Switches test of .data field to
.function, since .data will be going away.
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
setup_timer() was already being called before the open-coded init_timer()
and .data assignment. These are removed as well.
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
For small networks it is safe to reduce the subnet timeout from
its default value (18 for opensm) to 16. Make the SRP CM timeout
dependent on the subnet timeout such that decreasing the subnet
timeout also causes SRP failover and failback to occur faster.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This is a micro-optimization for the hot path.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Although in the RC mode more resources are needed that mode has three
advantages over SRQ:
- It works with all RDMA adapters, even those that do not support
SRQ.
- Posting WRs and polling WCs does not trigger lock contention
because only one thread at a time accesses a WR or WC queue in
non-SRQ mode.
- The end-to-end flow control mechanism is used.
>From the IB spec:
C9-150.2.1: For QPs that are not associated with an SRQ, each HCA
receive queue shall generate end-to-end flow control credits. If
a QP is associated with an SRQ, the HCA receive queue shall not
generate end-to-end flow control credits.
Add new configfs attributes that allow to configure which mode to use
(/sys/kernel/config/target/srpt/$GUID/$GUID/attrib/use_srq). Note:
only the attribute for port 1 is relevant on multi-port adapters.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch is a micro-optimization for the hot path.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Make srpt_parse_i_port_id() return a negative value if hex2bin()
fails.
Fixes: commit a42d985bd5 ("ib_srpt: Initial SRP Target merge for v3.3-rc1")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch reduces the number of #ifdefs and also avoids that
smatch reports the following:
drivers/infiniband/core/uverbs_ioctl.c:276: ib_uverbs_cmd_verbs() warn: if statement not indented
drivers/infiniband/core/uverbs_ioctl.c:280: ib_uverbs_cmd_verbs() warn: possible memory leak of 'ctx'
drivers/infiniband/core/uverbs_ioctl.c:315: ib_uverbs_cmd_verbs() warn: if statement not indented
References: commit fac9658cab ("IB/core: Add new ioctl interface")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Matan Barak <matanb@mellanox.com>
Cc: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Latest chip requires indexes 32 to 47 be used for the internal HW block
that manages queue mapping.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
test_bit() takes a bit number while the 'flags' field in
struct bnxt_qplib_rcfw was using actual BIT position converted
values.
Fix this by assigning bit numbers and use consistent APIs
all the flag values.
Also logging a message in case of failure.
Thanks to Dan Carpenter for pointing this out.
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Provide information about used firmware files via modinfo.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Trivial fix to spelling mistake in dev_err error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Per the IBTA spec, QP destroy shall fail if the QP is attached
to multicast groups, although the spec is silent on modify_qp
to reset state. It implies that ULP must deregister QP from
all mcast groups for destroy to succeed.
The faulty patch "IB/ipoib: Update broadcast object if PKey value
was changed in index 0" exposed two issues in rdmavt:
1. Rvt QP reset waits for qp references to go to zero.
This will hang if QP is attached to multicast groups.
2. The mcast group detach will fail for a QP in reset state
therefore preventing ULP from correcting the issue.
This patch moves the reference count wait to the the destroy QP
path and allows a QP mcast detach to work in the reset state.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Setting the protocol type should be part of initializing the tx request.
For UC and RC, the current protocol type is part of the qp priv structure.
For ud requests, it needs to be adjusted dynamically, based on the AV
posted with the WQE. This patch will simplify the initialization of the
tx request.
Fixes: 5b6cabb0db ("IB/hfi1: Add 16B RC/UC support")
Reviewed-by: Don Hiatt <don.hiatt@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The PIO trailing buffer was being dynamically allocated
but the kcalloc return value was not being checked. Further,
the GFP_KERNEL was being used even though the send engine
might be called with interrupts disabled.
Since the maximum size of the trailing buffer is only 12
bytes (CRC = 4, LT = 1, Pad = 0 to 7 bytes) just statically
allocate the buffer, remove the alloc entirely and share it
with the SDMA engine by making it global.
Reported-by: Leon Romanovsky <leon@kernel.org>
Fixes: 566d53a826 ("IB/hfi1: Enhance PIO/SDMA send for 16B")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The trace logic prior to the fixes below used to mask the
A bit from the psn. It now mistakenly displays the A bit,
which is already displayed separately.
Fix by adding the appropriate mask to the psn tracing.
Fixes: 228d2af1b7 ("IB/hfi1: Separate input/output header tracing")
Fixes: 863cf89d47 ("IB/hfi1: Add 16B trace support")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid acquiring already acquired hardware mutex and releasing
the unacquired one as these are redundant operations.
Add printouts for such situations to help detect potential errors
within the driver.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Grzegorz Morys <grzegorz.morys@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Parsing of platform configuration format 4 will fail on meta
version check. Allow meta version 4 during parsing.
Reviewed-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Change serdes mode setting to use MISC_CONFIG_BITS in
VERIFY_CAP_LOCAL_LINK_WIDTH register. This method of
setting up serdes loopback is universally compatible
across all firmware versions.
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Data structures should not be defined in a header file. Hence move
the min_transport_spec[] definition from a header file to a .c file.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Dave Goodell <dgoodell@cisco.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch avoids that sparse complains about missing declarations.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Dave Goodell <dgoodell@cisco.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that gcc 7 reports the following warning when building with W=1:
warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Cc: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that gcc 7 reports the following warning when building with W=1:
warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that gcc 7 reports the following warning when building with W=1:
warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Mike Marciniszyn <infinipath@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Due to removal of the EEPROM writing code, the qib_inc_eeprom_err()
macro became a no-op. Remove the code that calls it. Since that
change removes all code that reads the eep_st_masks array, also
remove the code that updates that array and the array itself.
References: commit 18c0b82a3e ("IB/qib: Do not write EEPROM")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Mike Marciniszyn <infinipath@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that gcc 7 reports the following warning when building with
W=1:
warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Selvin Xavier <selvin.xavier@broadcom.com>
Cc: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Faisal Latif <faisal.latif@intel.com>
Acked-by: Faisal Latif <fasial.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that gcc 7 reports the following warning when building with W=1:
warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Faisal Latif <faisal.latif@intel.com>
Acked-by: Faisal Latif <fasial.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
References: commit 5fe9dec0d0 ("IB/mlx5: Use blue flame register allocator in mlx5_ib")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that gcc 7 reports the following warning when building with W=1:
warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that gcc 7 reports the following warning when building with W=1:
warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that gcc 7 reports the following warning when building with W=1:
warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use the proper primitives to dereference the RCU pointer
upper_dev->ip_ptr. Compile-tested only.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch avoids that sparse complains that there is an address
space mismatch.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Lijun Ou <oulijun@huawei.com>
Cc: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Cc: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Move the hfi1_handle_cnp_tbl[] from a header file to a .c file
such that only one copy ends up in the hfi1 kernel module. This
patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that gcc 7 reports the following warning when building with W=1:
warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that gcc 7 reports the following warning when building with W=1:
warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch avoids that building the cxgb4 module with W=1 triggers
a complaint about a local variable that has not been declared static.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Steve Wise <swise@opengridcomputing.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Tell sparse what the locking assumptions are for __flush_qp() such
that it does not complain about the locking operations inside that
function.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that gcc 7 reports the following warning when building with W=1:
warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that gcc 7 reports the following warning when building with W=1:
warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
According to the C standard the behavior of computations with
integer operands is as follows:
* A computation involving unsigned operands can never overflow,
because a result that cannot be represented by the resulting
unsigned integer type is reduced modulo the number that is one
greater than the largest value that can be represented by the
resulting type.
* The behavior for signed integer underflow and overflow is
undefined.
Hence only use unsigned integers when checking for integer
overflow.
This patch is what I came up with after having analyzed the
following smatch warnings:
drivers/infiniband/core/cma.c:3448: cma_resolve_ib_udp() warn: signed overflow undefined. 'offset + conn_param->private_data_len < conn_param->private_data_len'
drivers/infiniband/core/cma.c:3505: cma_connect_ib() warn: signed overflow undefined. 'offset + conn_param->private_data_len < conn_param->private_data_len'
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that gcc 7 reports the following warning when building with W=1:
warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
To support passing child interfaces to the lower device a new
rdma_netdev function was used, set_id. This will allow us to
attach the PKEY index lower device resources such as TIS/QP.
For devices that do not support offloads in IPoIB same logic
will be used, setting the PKEY index to priv struct.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
When ndo_open and ndo_stop are called RTNL lock should be held.
In this specific case ipoib_ib_dev_open calls the offloaded ndo_open
which re-sets the number of TX queue assuming RTNL lock is held.
Since RTNL lock is not held, RTNL assert will fail.
Signed-off-by: Alex Vesker <valex@mellanox.com>
prot_sg_cnt cannot be zero as a previous check on ret (from which
prot_sg_cnt is assigned) returns -ENOMEM if is it zero. Since
it cannot be zero we can simplify the code by removing the non
-zero check on prot_sg_cnt and redundant else statement.
Detected by CoverityScan, COD#1357188 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Instead of making every caller convert the second argument of
sa_path_set_slid() and sa_path_set_dlid() to big endian format,
make these two functions accept LIDs in CPU endian format.
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Cc: Don Hiatt <don.hiatt@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The infiniband subsystem causes a link failure when the umem
driver is built on MMU-less systems:
mm/mmu_notifier.o: In function `do_mmu_notifier_register':
mmu_notifier.c:(.text+0x32): undefined reference to `mm_take_all_locks'
drivers/infiniband/core/umem.o: In function `ib_umem_get':
umem.c:(.text+0x132): undefined reference to `can_do_mlock'
drivers/infiniband/core/umem_odp.o: In function `ib_umem_odp_map_dma_pages':
umem_odp.c:(.text+0x766): undefined reference to `get_user_pages_remote'
This bug has existed for a while but only become apparent in ARM
randconfig builds when the dependency on PCI was lifted, as none
of the ARM-NOMMU targets support PCI at the moment.
We could probably get the umem driver to build by providing an
alternative implementation 'can_do_mlock()' that returns false
on NOMMU-systems, but then we'd still have a problem with the
mmu-notifiers required by CONFIG_INFINIBAND_ON_DEMAND_PAGING,
so simply forbidding umem with NOMMU seems like the simplest
workaround.
Fixes: 931bc0d916 ("IB: Move PCI dependency from root KConfig to HW's KConfigs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Alex Vesker <valex@mellanox.com>
Cc: Erez Shitrit <erezsh@mellanox.com>
Cc: Zhu Yanjun <yanjun.zhu@oracle.com>
Cc: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Yuval Shaia <yuval.shaia@oracle.com>
Cc: linux-rdma@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Faisal Latif <faisal.latif@intel.com>
Cc: Shiraz Saleem <shiraz.saleem@intel.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
helper to pass the timer pointer explicitly.
Cc: Mike Marciniszyn <infinipath@intel.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. A pointer from nesadapter back to
nesdev was added.
Cc: Faisal Latif <faisal.latif@intel.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If the allocation of elem fails, it is not sufficient to simply check
for NULL and return. We need to also put our reference on the pool or
else we will leave the pool with a permanent ref count and we will never
be able to free it.
Fixes: 4831ca9e4a ("IB/rxe: check for allocation failure on elem")
Suggested-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The allocation for elem may fail (especially because we're using
GFP_ATOMIC) so best to check for a null return. This fixes a potential
null pointer dereference when assigning elem->pool.
Detected by CoverityScan CID#1357507 ("Dereference null return value")
Fixes: 8700e3e7c4 ("Soft RoCE driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The s_ahgpsn was incorrectly placed in the read-mostly section of the QP
and the s_curr_size and s_hdrwords are oversized. The misplaced
s_ahgpsn will cause the read-mostly cachelines to thrash.
Place s_ahgpsn in the send side cache lines and correctly size and
s_hdrwords and s_cur_size to keep the send side cachelines at the same
size.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When the link is disabled and re-enabled, the host version bit is not
set again, so the firmware behaves as though it’s interacting with an
old driver. This causes LNI to get out of sync. The host version bit
needs to be set at load_8051_firmware() and _dc_start(). Currently, it's
only set at load_8051_firmware().
Create a common function to set the bit with the intent to make the code
more maintainable in the future, set the host version bit at _dc_start()
and modify the 8051 command API to prevent a deadlock as _dc_start() is
already holding the dc8051 lock.
Fixes: 913cc67159 ("IB/hfi1: Always perform offline transition")
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The addition of the VNIC contexts to num_rcv_contexts changes the
meaning of the sysfs value nctxts from available user contexts, to
user contexts + reserved VNIC contexts.
User applications that use nctxts are now broken.
Update the calculation so that VNIC contexts are used only if there are
hardware contexts available, and do not silently affect nctxts.
Update code to use the calculated VNIC context number.
Update the sysfs value nctxts to be available user contexts only.
Fixes: 2280740f01 ("IB/hfi1: Virtual Network Interface Controller (VNIC) HW support")
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Niranjana Vishwanathapura <Niranjana.Vishwanathapura@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: <Stable@vger.kernel.org> #v4.12+
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The 16B changes to the output side of the header trace introduced
two issues:
1. An uninitialized field "l4" for 9B packets
This field needs to be given a value of 0 for 9B
packets to insure a correct 9B trace.
The fix adds a new define to insure that there is a dummy
default for 9B packets to insure the correct string
is decoded.
2. Use of entry vs. __entry in field references
Fixes: Commit 863cf89d47 ("IB/hfi1: Add 16B trace support")
Reported-by: Kaike Wan <kaike.wan@intel.com>
Reviewed-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Platform configuration format version 4, that didn't use the file
size field, is not parsed by the host driver. Only version 5 is
supported. Add logic in parsing procedure to determine what format
is being used and allow to read data from version 4 files.
Reviewed-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Andrzej Kacprowski <andrzej.kacprowski@intel.com>
Signed-off-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
A Work Request (WR) posted after QP is flushed will not
get a flush completion.
Correct this problem by not allowing posting of WRs
after a QP is flushed.
Fixes: d374984179 ("i40iw: add files for iwarp interface")
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If RTR WQE is posted and QP is flushed, a CQE is
incorrectly generated for the RTR WQE. Add code
to look for the RTR and not generate a CQE when
QP is flushed.
Fixes: 280cfc4b74 ("i40iw: user kernel shared files")
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The ACK packets for an MPA request are ignored and
the MPA request is retransmitted if the MPA reply
is late or missing. Fix this by checking ack_rcvd
variable before retransmitting a packet.
Fixes: f27b4746f3 ("i40iw: add connection management code")
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Port number 0 is an invalid port number. Set it to 1
as there is one port per i40iw device.
Fixes: d374984179 ("i40iw: add files for iwarp interface")
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove duplicate set_64bit_val call to offset 24.
Replace some instances of set_64bit_val with
i40iw_insert_wqe_hdr as valid bit needs a write
barrier and should be the last write operation for the WQE.
Fixes: 786c6adb3a ("i40iw: add puda code")
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Parse the vlan priority from the vlan tag and configure it to the
WC's sl field.
Fixes: abd49676c7 ("qed: Add RoCE ll2 & GSI support")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Rename vlan_id field name to vlan as it contains more than the vlan_id.
Mask out non vlan id fields from vlan tag of the QED LL2 RX GSI
vlan output. As it is expected to be vlan id only.
Ignore vlan_id with value of zero.
Fixes: abd49676c7 ("qed: Add RoCE ll2 & GSI support")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When UAR get_page fails, it needs to continue to cleanup debugfs for
congestion control parameters. Labels for error path were incorrectly
ordered.
This patch fixes to do correct cleanup on debugfs init failure and uar
get page failure.
Fixes: 4a2da0b8c0 ("IB/mlx5: Add debug control parameters for congestion control")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
For the case where hr_qp->state == IB_QPS_RESET, an uninitialized
value in ret is being returned by function hns_roce_v2_query_qp.
Fix this by setting ret to 0 for this specific return condition.
Detected by CoverityScan, CID#1457203 ("Unitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The driver doesn't actually register an inetaddr notifier function,
so there is no need to unregister it on shutdown.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
After the loop in hns_roce_v1_mr_free_work_fn function, it is possible that
all qps will have been freed (in which case ne will be 0). If that
happens, then later in the function when we dereference hr_qp we will
get an exception. Check ne is not 0 to make sure we actually have an
hr_qp left to work on.
This patch fixes the smatch error as below:
drivers/infiniband/hw/hns/hns_roce_hw_v1.c:1009 hns_roce_v1_mr_free_work_fn()
error: we previously assumed 'hr_qp' could be null
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When querying qp, It needs to return RoCE device ah_attr type
that may be specific to RoCE devices.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Only when the IB_QP_DEST_QPN flag of attr_mask is set is it valid to
assign the dest_qp_num into the dest_qp field of qp context.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When lp_qp_work is NULL, we should return ENOMEM. In order to do so,
we had to make some upper layer functions return a value instead
of being void type so we can propagate the error up the stack.
This patch fixes the smatch error as below:
drivers/infiniband/hw/hns/hns_roce_hw_v1.c:918 hns_roce_v1_recreate_lp_qp()
error: potential null dereference 'lp_qp_work'. (kzalloc returns null)
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Put the code for checking the send doorbell status into a
separate function and call it from check_qp_db_process_status
to improve indenting and readability.
It fixes the warning from static checker:
drivers/infiniband/hw/hns/hns_roce_hw_v1.c:3562 check_qp_db_process_status()
warn: inconsistent indenting.
Fixes: 5f110ac4be ("IB/hns: Fix for checkpatch.pl comment style)
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The value of max_rd_atomic and max_dest_rd_atomic in query_qp
are incorrect. It should be assigned by left shifting of
the bit in hip06 SoC.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
For messages sent from the host to fw that solicit a reply from fw,
the c4iw_wr_wait struct pointer is passed in the host->fw message, and
included in the fw->host fw6_msg reply. This allows the sender to wait
until the reply is received, and the code processing the ingress reply
to wake up the sender.
If c4iw_wait_for_reply() times out, however, we need to keep the
c4iw_wr_wait object around in case the reply eventually does arrive.
Otherwise we have touch-after-free bugs in the wake_up paths.
This was hit due to a bad kernel driver that blocked ingress processing
of cxgb4 for a long time, causing iw_cxgb4 timeouts, but eventually
resuming ingress processing and thus hitting the touch-after-free bug.
So I want to fix iw_cxgb4 such that we'll at least keep the wait object
around until the reply comes. If it never comes we leak a small amount of
memory, but if it does come late, we won't potentially crash the system.
So add a kref struct in the c4iw_wr_wait struct, and take a reference
before sending a message to FW that will generate a FW6 reply. And remove
the reference (and potentially free the wait object) when the reply
is processed.
The ep code also uses the wr_wait for non FW6 CPL messages and doesn't
embed the c4iw_wr_wait object in the message sent to firmware. So for
those cases we add c4iw_wake_up_noref().
The mr/mw, cq, and qp object create/destroy paths do need this reference
logic. For these paths, c4iw_ref_send_wait() is introduced to take the
wr_wait reference, send the msg to fw, and then wait for the reply.
So going forward, iw_cxgb4 either uses c4iw_ofld_send(),
c4iw_wait_for_reply() and c4iw_wake_up_noref() like is done in the some
of the endpoint logic, or c4iw_ref_send_wait() and c4iw_wake_up_deref()
(formerly c4iw_wake_up()) when sending messages with the c4iw_wr_wait
object pointer embedded in the message and resulting FW6 reply.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove the embedded c4iw_wr_wait object in preparation for correctly
handling timeouts.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove the local stack allocated c4iw_wr_wait object in preparation for
correctly handling timeouts.
Also cleaned up some error path unwind logic to make it more readable.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove the local stack allocated c4iw_wr_wait object in preparation for
correctly handling timeouts.
Also cleaned up some error path unwind logic to make it more readable.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove the local stack allocated c4iw_wr_wait object in preparation for
correctly handling timeouts.
Also refactored some code to simplify it and make errpath unwinding
more readable.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Commit 1a1c116f3d removes nlmsg_len calculation in
ibnl_put_attr causing netlink messages to be rejected due
to incorrect length.
Add nlmsg_end after all attributes are appended to calculate
the nlmsg_len.
Fixes: 1a1c116f3d ("RDMA/netlink: Simplify the put_msg and put_attr")
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Variable j is being assigned to loop_j and then later being
assigned to a new value in for loops. The first initialization
is therefore redundant and can be removed.
Cleans up clang warning:
warning: Value stored to 'j' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
