Adds pinmux and DT node for Micron (MT29F4G08AB) x8 NAND device present on
am437x-gp-evm board.
(1) As NAND Flash data lines are muxed with eMMC, Thus at a given time either
eMMC or NAND can be enabled. Selection between eMMC and NAND is controlled:
(a) By dynamically driving following GPIO pin from software
SPI2_CS0(GPIO) == 0 NAND is selected (default)
SPI2_CS0(GPIO) == 1 eMMC is selected
(b) By statically using Jumper (J89) on the board
(2) As NAND device connnected to this board has page-size=4K and oob-size=224,
So ROM code expects boot-loaders to be flashed in BCH16 ECC scheme for
NAND boot.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add CPSW ethernet support for AM437x GP EVM which has one slave pinned out
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The VTT regulator for DDR3 termination on the am437x-gp-evm is
controlled by a gpio. It is configured by the bootloader so here we
define an always-on, fixed voltage regulator to hold the gpio.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add touchscreen support for AM437x GP EVM using pixcir
touchscreen controller.
CC: Benoit Cousson <bcousson@baylibre.com>
CC: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable
- USB PHY
- USB
for am437x-gp-evm
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Do not reset GPIO5 at boot-up because GPIO5_7 is used
on AM437x GP-EVM to control VTT regulators on DDR3.
Without this some GP-EVM boards will fail to boot because
of DDR3 corruption.
Reported-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
enable sd card slot on am437x-gp-evm
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable gpio3, gpio4, it will be used by gpio matrix keys. Also,
can be used by othe peripherals.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
AM437x GP EVM DTS with pinmux information to make I2C on
EVM usable.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
