We introduced a couple new error paths which are missing unlocks.
Fixes: 7760e14835 ('[media] af9035: Don't use dynamic static allocation')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: stable@vger.kernel.org
Driver did not work anymore since I2C has gone broken due
to recent commit:
commit 37ebaf6891
[media] dvb-frontends: Don't use dynamic static allocation
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: stable@vger.kernel.org
The remote subdev of any video node in the OMAP3 ISP is an internal
subdev that is guaranteed to implement get_fmt. Don't check the return
value for -ENOIOCTLCMD, as this can't happen.
While at it, move non-critical code out of the mutex-protected section.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was three small buffer len calculation bugs which caused
driver non-working. These are coming from recent commit:
commit 7760e14835
[media] af9035: Don't use dynamic static allocation
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: stable@vger.kernel.org
The configuration of many other blocks depend on resizer maximum data rate.
Get the value from resizer at link validation time.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mark pads that must be connected.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not allow streaming if a pad with MEDIA_PAD_FL_MUST_CONNECT flag is not
connected by an active link.
This patch makes it possible to avoid drivers having to check for the most
common case of link state validation: a sink pad that must be connected.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch uses devm to release the clks instead of releasing
manually.
And it adds enable/disable mipi_clk when getting its rate.
Signed-off-by: Libin Yang <lbyang@marvell.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The mmp-driver is using devm_* to allocate the resource. The old
resource release methods are not appropriate here.
Signed-off-by: Libin Yang <lbyang@marvell.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.12 and up
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
git grep shows that the function is only called from ths7303.c
Fix this build warning:
CC drivers/media/i2c/ths7303.o
drivers/media/i2c/ths7303.c:86:5: warning: no previous prototype for ‘ths7303_setval’ [-Wmissing-prototypes]
int ths7303_setval(struct v4l2_subdev *sd, enum ths7303_filter_mode mode)
^
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
vb2_fop_release might take the video queue mutex lock.
In order to avoid nesting mutexes the private mutex is taken after the
fop_release has finished.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 5aa9ae5ed5 inverted the mute control
state test in s_routing which caused the audio routing to fail. This broke
ivtv support for the Hauppauge video/audio input bracket (which adds additional
video and audio inputs) all the way back in kernel 2.6.36.
This fix fixes the condition and it also removes a nonsense check on the
balance control.
Bisected-by: Rajil Saraswat <rajil.s@gmail.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Reported-by: Rajil Saraswat <rajil.s@gmail.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.10 and up
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The mmp-driver is using devm_* to allocate the resource. The old
resource release methods are not appropriate here.
Signed-off-by: Libin Yang <lbyang@marvell.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.12 and up
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When adding frequency clamping to the tef6862 and radio-tea5764 drivers
I forgot to actually *assign* the clamp result to the frequency.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Hans Petter Selasky <hps@bitfrost.no>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org # for 3.11 and up
We dereference "dev" after it has already been freed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In case of error, the function kthread_run() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The no_video flag was checked in all other cases except one. Calling
v4l2_ctrl_handler_setup() if no_video is 1 will crash.
This wasn't noticed before since there are only two card types that
set no_video to 1, so this type of hardware is quite rare.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Lorenz Röhrl <sheepshit@gmx.de>
Tested-by: Lorenz Röhrl <sheepshit@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It is IT9135 dual design.
Thanks to Michael Piko for reporting that!
Reported-by: Michael Piko <michael@piko.com.au>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently it is not possible for userspace to map a DMABUF exported buffer
with write permissions. This patch allows to also pass O_RDONLY/O_RDWR when
exporting the buffer, so that userspace may map it with write permissions.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The variable txlen was used instead of rxlen in boundary check.
(copy-paste error)
Signed-off-by: Felipe Pena <felipensp@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
removes trailing whitespace and rebalance line length in comment block
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
dmx_section_feed_release_filter() locks dvbdmx->mutex and
if the feed is still filtering, it calls feed->stop_filtering(feed).
stop_filtering() is implemented by dmx_section_feed_stop_filtering()
that first of all try to lock the same mutex: dvbdmx->mutex.
That leads to a deadlock.
It does not happen often in practice because all callers of
release_filter() stop filtering by themselves.
So the problem can happen in case of race condition only.
The patch releases dvbdmx->mutex before call to feed->stop_filtering(feed)
and reacquires the mutex after that.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This mirrors the patch to the radio-shark driver by Geert Uytterhoeven.
If SHARK_USE_LEDS=1, but CONFIG_PM=n:
drivers/media/radio/radio-shark2.c:240: warning: ‘shark_resume_leds’ defined but not used
Instead of making the #ifdef logic even more complicated (there are already
two definitions of shark_resume_leds()), mark shark_resume_leds() inline to
kill the compiler warning. shark_resume_leds() is small and it has only one
caller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a small delay at the end of configure_clock() to allow sensor to initialize.
This is needed by Asus VX2S laptop webcam to detect sensor type properly (the already-supported MT9M112).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If SHARK_USE_LEDS=1, but CONFIG_PM=n:
drivers/media/radio/radio-shark.c:275: warning: ‘shark_resume_leds’ defined but not used
Instead of making the #ifdef logic even more complicated (there are already
two definitions of shark_resume_leds()), mark shark_resume_leds() inline to
kill the compiler warning. shark_resume_leds() is small and it has only one
caller.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull slave-dmaengine changes from Vinod Koul:
"This brings for slave dmaengine:
- Change dma notification flag to DMA_COMPLETE from DMA_SUCCESS as
dmaengine can only transfer and not verify validaty of dma
transfers
- Bunch of fixes across drivers:
- cppi41 driver fixes from Daniel
- 8 channel freescale dma engine support and updated bindings from
Hongbo
- msx-dma fixes and cleanup by Markus
- DMAengine updates from Dan:
- Bartlomiej and Dan finalized a rework of the dma address unmap
implementation.
- In the course of testing 1/ a collection of enhancements to
dmatest fell out. Notably basic performance statistics, and
fixed / enhanced test control through new module parameters
'run', 'wait', 'noverify', and 'verbose'. Thanks to Andriy and
Linus [Walleij] for their review.
- Testing the raid related corner cases of 1/ triggered bugs in
the recently added 16-source operation support in the ioatdma
driver.
- Some minor fixes / cleanups to mv_xor and ioatdma"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (99 commits)
dma: mv_xor: Fix mis-usage of mmio 'base' and 'high_base' registers
dma: mv_xor: Remove unneeded NULL address check
ioat: fix ioat3_irq_reinit
ioat: kill msix_single_vector support
raid6test: add new corner case for ioatdma driver
ioatdma: clean up sed pool kmem_cache
ioatdma: fix selection of 16 vs 8 source path
ioatdma: fix sed pool selection
ioatdma: Fix bug in selftest after removal of DMA_MEMSET.
dmatest: verbose mode
dmatest: convert to dmaengine_unmap_data
dmatest: add a 'wait' parameter
dmatest: add basic performance metrics
dmatest: add support for skipping verification and random data setup
dmatest: use pseudo random numbers
dmatest: support xor-only, or pq-only channels in tests
dmatest: restore ability to start test at module load and init
dmatest: cleanup redundant "dmatest: " prefixes
dmatest: replace stored results mechanism, with uniform messages
Revert "dmatest: append verify result to results"
...
Pull i2c changes from Wolfram Sang:
- new drivers for exynos5, bcm kona, and st micro
- bigger overhauls for drivers mxs and rcar
- typical driver bugfixes, cleanups, improvements
- got rid of the superfluous 'driver' member in i2c_client struct This
touches a few drivers in other subsystems. All acked.
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: bcm-kona: fix error return code in bcm_kona_i2c_probe()
i2c: i2c-eg20t: do not print error message in syslog if no ACK received
i2c: bcm-kona: Introduce Broadcom I2C Driver
i2c: cbus-gpio: Fix device tree binding
i2c: wmt: add missing clk_disable_unprepare() on error
i2c: designware: add new ACPI IDs
i2c: i801: Add Device IDs for Intel Wildcat Point-LP PCH
i2c: exynos5: Remove incorrect clk_disable_unprepare
i2c: i2c-st: Add ST I2C controller
i2c: exynos5: add High Speed I2C controller driver
i2c: rcar: fixup rcar type naming
i2c: scmi: remove some bogus NULL checks
i2c: sh_mobile & rcar: Enable the driver on all ARM platforms
i2c: sh_mobile: Convert to clk_prepare/unprepare
i2c: mux: gpio: use reg value for i2c_add_mux_adapter
i2c: mux: gpio: use gpio_set_value_cansleep()
i2c: Include linux/of.h header
i2c: mxs: Fix PIO mode on i.MX23
i2c: mxs: Rework the PIO mode operation
i2c: mxs: distinguish i.MX23 and i.MX28 based I2C controller
...
Pull media build fixes from Mauro Carvalho Chehab:
"A series of patches that fix compilation on non-x86 archs.
While most of them are just build fixes, there are some fixes for real
bugs, as there are a number of drivers using dynamic stack allocation.
A few of those might be considered a security risk, if the i2c-dev
module is loaded, as someone could be sending very long I2C data that
could potentially overflow the Kernel stack. Ok, as using /dev/i2c-*
devnodes usually requires root on usual distros, and exploiting it
would require a DVB board or USB stick, the risk is not high"
* 'topic/kbuild-fixes-for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (28 commits)
[media] platform drivers: Fix build on frv arch
[media] lirc_zilog: Don't use dynamic static allocation
[media] mxl111sf: Don't use dynamic static allocation
[media] af9035: Don't use dynamic static allocation
[media] af9015: Don't use dynamic static allocation
[media] dw2102: Don't use dynamic static allocation
[media] dibusb-common: Don't use dynamic static allocation
[media] cxusb: Don't use dynamic static allocation
[media] v4l2-async: Don't use dynamic static allocation
[media] cimax2: Don't use dynamic static allocation
[media] tuner-xc2028: Don't use dynamic static allocation
[media] tuners: Don't use dynamic static allocation
[media] av7110_hw: Don't use dynamic static allocation
[media] stv090x: Don't use dynamic static allocation
[media] stv0367: Don't use dynamic static allocation
[media] stb0899_drv: Don't use dynamic static allocation
[media] dvb-frontends: Don't use dynamic static allocation
[media] dvb-frontends: Don't use dynamic static allocation
[media] s5h1420: Don't use dynamic static allocation
[media] uvc/lirc_serial: Fix some warnings on parisc arch
...
Pull media updates from Mauro Carvalho Chehab:
"This series include:
- a new Remote Controller driver for ST SoC with the corresponding DT
bindings
- a new frontend (cx24117)
- a new I2C camera flash driver (lm3560)
- a new mem2mem driver for TI SoC (ti-vpe)
- support for Raphael r828d added to r820t driver
- some improvements on buffer allocation at VB2 core
- usual driver fixes and improvements
PS this time, we have a smaller number of patches. While it is hard
to pinpoint to the reasons, I believe that it is mainly due to:
1) there are several patch series ready, but depending on DT review.
I decided to grant some extra time for DT maintainers to look on
it, as they're expecting to have more time with the changes agreed
during ARM mini-summit and KS. If they can't review in time for
3.14, I'll review myself and apply for the next merge window.
2) I suspect that having both LinuxCon EU and LinuxCon NA happening
during the same merge window affected the development
productivity, as several core media developers participated on
both events"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (151 commits)
[media] media: st-rc: Add ST remote control driver
[media] gpio-ir-recv: Include linux/of.h header
[media] tvp7002: Include linux/of.h header
[media] tvp514x: Include linux/of.h header
[media] ths8200: Include linux/of.h header
[media] adv7343: Include linux/of.h header
[media] v4l: Fix typo in v4l2_subdev_get_try_crop()
[media] media: i2c: add driver for dual LED Flash, lm3560
[media] rtl28xxu: add 15f4:0131 Astrometa DVB-T2
[media] rtl28xxu: add RTL2832P + R828D support
[media] rtl2832: add new tuner R828D
[media] r820t: add support for R828D
[media] media/i2c: ths8200: fix build failure with gcc 4.5.4
[media] Add support for KWorld UB435-Q V2
[media] staging/media: fix msi3101 build errors
[media] ddbridge: Remove casting the return value which is a void pointer
[media] ngene: Remove casting the return value which is a void pointer
[media] dm1105: remove unneeded not-null test
[media] sh_mobile_ceu_camera: remove deprecated IRQF_DISABLED
[media] media: rcar_vin: Add preliminary r8a7790 support
...
Pull dmaengine changes from Dan
1/ Bartlomiej and Dan finalized a rework of the dma address unmap
implementation.
2/ In the course of testing 1/ a collection of enhancements to dmatest
fell out. Notably basic performance statistics, and fixed / enhanced
test control through new module parameters 'run', 'wait', 'noverify',
and 'verbose'. Thanks to Andriy and Linus for their review.
3/ Testing the raid related corner cases of 1/ triggered bugs in the
recently added 16-source operation support in the ioatdma driver.
4/ Some minor fixes / cleanups to mv_xor and ioatdma.
Conflicts:
drivers/dma/dmatest.c
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
Merge first patch-bomb from Andrew Morton:
"Quite a lot of other stuff is banked up awaiting further
next->mainline merging, but this batch contains:
- Lots of random misc patches
- OCFS2
- Most of MM
- backlight updates
- lib/ updates
- printk updates
- checkpatch updates
- epoll tweaking
- rtc updates
- hfs
- hfsplus
- documentation
- procfs
- update gcov to gcc-4.7 format
- IPC"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (269 commits)
ipc, msg: fix message length check for negative values
ipc/util.c: remove unnecessary work pending test
devpts: plug the memory leak in kill_sb
./Makefile: export initial ramdisk compression config option
init/Kconfig: add option to disable kernel compression
drivers: w1: make w1_slave::flags long to avoid memory corruption
drivers/w1/masters/ds1wm.cuse dev_get_platdata()
drivers/memstick/core/ms_block.c: fix unreachable state in h_msb_read_page()
drivers/memstick/core/mspro_block.c: fix attributes array allocation
drivers/pps/clients/pps-gpio.c: remove redundant of_match_ptr
kernel/panic.c: reduce 1 byte usage for print tainted buffer
gcov: reuse kbasename helper
kernel/gcov/fs.c: use pr_warn()
kernel/module.c: use pr_foo()
gcov: compile specific gcov implementation based on gcc version
gcov: add support for gcc 4.7 gcov format
gcov: move gcov structs definitions to a gcc version specific file
kernel/taskstats.c: return -ENOMEM when alloc memory fails in add_del_listener()
kernel/taskstats.c: add nla_nest_cancel() for failure processing between nla_nest_start() and nla_nest_end()
kernel/sysctl_binary.c: use scnprintf() instead of snprintf()
...
Pull vfs updates from Al Viro:
"All kinds of stuff this time around; some more notable parts:
- RCU'd vfsmounts handling
- new primitives for coredump handling
- files_lock is gone
- Bruce's delegations handling series
- exportfs fixes
plus misc stuff all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (101 commits)
ecryptfs: ->f_op is never NULL
locks: break delegations on any attribute modification
locks: break delegations on link
locks: break delegations on rename
locks: helper functions for delegation breaking
locks: break delegations on unlink
namei: minor vfs_unlink cleanup
locks: implement delegations
locks: introduce new FL_DELEG lock flag
vfs: take i_mutex on renamed file
vfs: rename I_MUTEX_QUOTA now that it's not used for quotas
vfs: don't use PARENT/CHILD lock classes for non-directories
vfs: pull ext4's double-i_mutex-locking into common code
exportfs: fix quadratic behavior in filehandle lookup
exportfs: better variable name
exportfs: move most of reconnect_path to helper function
exportfs: eliminate unused "noprogress" counter
exportfs: stop retrying once we race with rename/remove
exportfs: clear DISCONNECTED on all parents sooner
exportfs: more detailed comment for path_reconnect
...
Since gen_pool_dma_alloc() is introduced, we implement it to simplify code.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
This branch contains code cleanups, moves and removals for 3.13.
Qualcomm msm targets had a bunch of code removal for legacy non-DT
platforms. Nomadik saw more device tree conversions and cleanup of old
code. Tegra has some code refactoring, etc.
One longish patch series from Sebastian Hasselbarth changes the init_time
hooks and tries to use a generic implementation for most platforms,
since they were all doing more or less the same things.
Finally the "shark" platform is removed in this release. It's been
abandoned for a while and nobody seems to care enough to keep it
around. If someone comes along and wants to resurrect it, the removal
can easily be reverted and code brought back.
Beyond this, mostly a bunch of removals of stale content across the
board, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSgBqdAAoJEIwa5zzehBx3cIEP/0L8ayPZV/fFpF3VheP7nyq9
nanUc74GVHu71rhiACsfqsP9QGQT6Ye+RNvD8gVcmmqW+7TjWG19nwgjO+GbJmIF
Sr5jNaSLy2yeMHd6aEOTYtpQ/kUdFePvEVMVJG4nx8vVa0sxk7YCIsHFNQTV4Wgv
FOnJ2jx3RvM6ing5SfmglB3ai7dwYxKKCZvzLqzn2vs0W+Fw0jXv/OEjbdd+WAfK
K94lFIqQXcxyDeF2NTVtlFT/F+LKbiRP88kM2ZkJkz5RHcSXgJNmJmVDCHwGxH08
ri9QOX6stHT6gNFl/B5ckpzg5PbuzkEnlg1GXWn7fnx7OoBKekx8SKoP0+sjkpxF
kX5pfERdBHUju1mfHDkxfdPAQ4RFDVcYDwNoTC1zBhDSfMuFsTGGNdeR0dhGQnmA
Vzc8RfIRzFhGEuXDktz7cZIpOuq7OI62jt6qDLqWSWSOa9ZfqsOMdCcA3QTV3rTi
nHiOQBTM0Bl78SrXzE0PmcD4obCnBvJqthSF5Z09N/POBtz8i4GsF7k4S1rr/rvX
HA/wp9Lzt4hvCoj1gwEGLqUnSiey1b7a3rqn03mNQvX7NW9StIg1VCauQZBR1KwP
Xtxgt48QgjQ7wzh4RGs2FdAgW4cw9nEbUTVRBLkQ7jxW+zh5CRJlS5dprBMR7Ier
7necO/DWPLnhaSAj4eXB
=SHZQ
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.13.
Qualcomm msm targets had a bunch of code removal for legacy non-DT
platforms. Nomadik saw more device tree conversions and cleanup of
old code. Tegra has some code refactoring, etc.
One longish patch series from Sebastian Hasselbarth changes the
init_time hooks and tries to use a generic implementation for most
platforms, since they were all doing more or less the same things.
Finally the "shark" platform is removed in this release. It's been
abandoned for a while and nobody seems to care enough to keep it
around. If someone comes along and wants to resurrect it, the removal
can easily be reverted and code brought back.
Beyond this, mostly a bunch of removals of stale content across the
board, etc"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (79 commits)
ARM: gemini: convert to GENERIC_CLOCKEVENTS
ARM: EXYNOS: remove CONFIG_MACH_EXYNOS[4, 5]_DT config options
ARM: OMAP3: control: add API for setting IVA bootmode
ARM: OMAP3: CM/control: move CM scratchpad save to CM driver
ARM: OMAP3: McBSP: do not access CM register directly
ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock
ARM: OMAP2: CM/PM: remove direct register accesses outside CM code
MAINTAINERS: Add patterns for DTS files for AT91
ARM: at91: remove init_machine() as default is suitable
ARM: at91/dt: split sama5d3 peripheral definitions
ARM: at91/dt: split sam9x5 peripheral definitions
ARM: Remove temporary sched_clock.h header
ARM: clps711x: Use linux/sched_clock.h
MAINTAINERS: Add DTS files to patterns for Samsung platform
ARM: EXYNOS: remove unnecessary header inclusions from exynos4/5 dt machine file
ARM: tegra: fix ARCH_TEGRA_114_SOC select sort order
clk: nomadik: fix missing __init on nomadik_src_init
ARM: drop explicit selection of HAVE_CLK and CLKDEV_LOOKUP
ARM: S3C64XX: Kill CONFIG_PLAT_S3C64XX
ASoC: samsung: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
...
On frv, the following errors happen:
drivers/media/platform/soc_camera/rcar_vin.c: In function 'rcar_vin_setup':
drivers/media/platform/soc_camera/rcar_vin.c:284:3: error: implicit declaration of function 'iowrite32' [-Werror=implicit-function-declaration]
drivers/media/platform/soc_camera/rcar_vin.c: In function 'rcar_vin_request_capture_stop':
drivers/media/platform/soc_camera/rcar_vin.c:353:2: error: implicit declaration of function 'ioread32' [-Werror=implicit-function-declaration]
This is because this driver forgot to include linux/io.h.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb-v2/mxl111sf.c:74:1: warning: 'mxl111sf_ctrl_msg' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer to be the max size of
a control URB payload data (64 bytes).
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb-v2/af9035.c:142:1: warning: 'af9035_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/usb/dvb-usb-v2/af9035.c:305:1: warning: 'af9035_i2c_master_xfer' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer to be the max size of
a control URB payload data (64 bytes).
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb-v2/af9015.c:433:1: warning: 'af9015_eeprom_hash' uses dynamic stack allocation [enabled by default]
In this specific case, it is a gcc bug, as the size is a const, but
it is easy to just change it from const to a #define, getting rid of
the gcc warning.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb/dw2102.c:368:1: warning: 'dw2102_earda_i2c_transfer' uses dynamic stack allocation [enabled by default]
drivers/media/usb/dvb-usb/dw2102.c:449:1: warning: 'dw2104_i2c_transfer' uses dynamic stack allocation [enabled by default]
drivers/media/usb/dvb-usb/dw2102.c:512:1: warning: 'dw3101_i2c_transfer' uses dynamic stack allocation [enabled by default]
drivers/media/usb/dvb-usb/dw2102.c:621:1: warning: 's6x0_i2c_transfer' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer to be the max size of
a control URB payload data (64 bytes).
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb/dibusb-common.c:124:1: warning: 'dibusb_i2c_msg' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer to be the max size of
a control URB payload data (64 bytes).
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/usb/dvb-usb/cxusb.c:209:1: warning: 'cxusb_i2c_xfer' uses dynamic stack allocation [enabled by default]
drivers/media/usb/dvb-usb/cxusb.c:69:1: warning: 'cxusb_ctrl_msg' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer to be the max size of
a control URB payload data (64 bytes).
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/v4l2-core/v4l2-async.c:238:1: warning: 'v4l2_async_notifier_unregister' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer.
In this specific case, there's a hard limit imposed by V4L2_MAX_SUBDEVS,
with is currently 128. That means that the buffer size can be up to
128x8 = 1024 bytes (on a 64bits kernel), with is too big for stack.
Worse than that, someone could increase it and cause real troubles.
So, let's use dynamically allocated data, instead.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/pci/cx23885/cimax2.c:149:1: warning: 'netup_write_i2c' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/tuners/tuner-xc2028.c:651:1: warning: 'load_firmware' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer.
In the specific case of this driver, the maximum limit is 80, used only
on tm6000 driver. This limit is due to the size of the USB control URBs.
Ok, it would be theoretically possible to use a bigger size on PCI
devices, but the firmware load time is already good enough. Anyway,
if some usage requires more, it is just a matter of also increasing
the buffer size at load_firmware().
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/tuners/e4000.c:50:1: warning: 'e4000_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/e4000.c:83:1: warning: 'e4000_rd_regs' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/fc2580.c:66:1: warning: 'fc2580_wr_regs.constprop.1' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/fc2580.c:98:1: warning: 'fc2580_rd_regs.constprop.0' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/tda18212.c:57:1: warning: 'tda18212_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/tda18212.c:90:1: warning: 'tda18212_rd_regs.constprop.0' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/tda18218.c:60:1: warning: 'tda18218_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/tuners/tda18218.c:92:1: warning: 'tda18218_rd_regs.constprop.0' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/pci/ttpci/av7110_hw.c:510:1: warning: 'av7110_fw_cmd' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer.
In the specific case of this driver, the maximum fw command size
is 6 + 2, as checked using:
$ git grep -A1 av7110_fw_cmd drivers/media/pci/ttpci/
So, use 8 for the buffer size.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/stv090x.c:750:1: warning: 'stv090x_write_regs.constprop.6' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/stv0367.c:791:1: warning: 'stv0367_writeregs.constprop.4' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/stb0899_drv.c:540:1: warning: 'stb0899_write_regs' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/af9013.c:77:1: warning: 'af9013_wr_regs_i2c' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/af9033.c:188:1: warning: 'af9033_wr_reg_val_tab' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/af9033.c:68:1: warning: 'af9033_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/bcm3510.c:230:1: warning: 'bcm3510_do_hab_cmd' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/cxd2820r_core.c:84:1: warning: 'cxd2820r_rd_regs_i2c.isra.1' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/rtl2830.c:56:1: warning: 'rtl2830_wr' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/rtl2832.c:187:1: warning: 'rtl2832_wr' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/tda10071.c:52:1: warning: 'tda10071_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/tda10071.c:84:1: warning: 'tda10071_rd_regs' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/bcm3510.c:230:1: warning: 'bcm3510_do_hab_cmd' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/itd1000.c:69:1: warning: 'itd1000_write_regs.constprop.0' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/mt312.c:126:1: warning: 'mt312_write' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/nxt200x.c:111:1: warning: 'nxt200x_writebytes' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/stb6100.c:216:1: warning: 'stb6100_write_reg_range.constprop.3' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/stv6110.c:98:1: warning: 'stv6110_write_regs' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/stv6110x.c:85:1: warning: 'stv6110x_write_regs' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/tda18271c2dd.c:147:1: warning: 'WriteRegs' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/zl10039.c:119:1: warning: 'zl10039_write' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/s5h1420.c:851:1: warning: 's5h1420_tuner_i2c_tuner_xfer' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer.
In the specific case of this frontend, only ttpci uses it. The maximum
number of messages there is two, on I2C read operations. As the logic
can add an extra operation, change the size to 3.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On this arch, usec is not unsigned long. So, we need to typecast,
in order to remove those warnings:
drivers/media/usb/uvc/uvc_video.c: In function 'uvc_video_clock_update':
drivers/media/usb/uvc/uvc_video.c:678:2: warning: format '%lu' expects argument of type 'long unsigned int', but argument 9 has type '__kernel_suseconds_t' [-Wformat]
drivers/staging/media/lirc/lirc_serial.c: In function 'irq_handler':
drivers/staging/media/lirc/lirc_serial.c:707:5: warning: format '%lx' expects argument of type 'long unsigned int', but argument 6 has type '__kernel_suseconds_t' [-Wformat]
drivers/staging/media/lirc/lirc_serial.c:707:5: warning: format '%lx' expects argument of type 'long unsigned int', but argument 7 has type '__kernel_suseconds_t' [-Wformat]
drivers/staging/media/lirc/lirc_serial.c:719:5: warning: format '%lx' expects argument of type 'long unsigned int', but argument 6 has type '__kernel_suseconds_t' [-Wformat]
drivers/staging/media/lirc/lirc_serial.c:719:5: warning: format '%lx' expects argument of type 'long unsigned int', but argument 7 has type '__kernel_suseconds_t' [-Wformat]
drivers/staging/media/lirc/lirc_serial.c:728:6: warning: format '%lx' expects argument of type 'long unsigned int', but argument 6 has type '__kernel_suseconds_t' [-Wformat]
drivers/staging/media/lirc/lirc_serial.c:728:6: warning: format '%lx' expects argument of type 'long unsigned int', but argument 7 has type '__kernel_suseconds_t' [-Wformat]
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix the following warnings:
drivers/media/rc/fintek-cir.c: In function 'fintek_cr_write':
drivers/media/rc/fintek-cir.c:45:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/fintek-cir.c:46:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/fintek-cir.c: In function 'fintek_cr_read':
drivers/media/rc/fintek-cir.c:54:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/fintek-cir.c:55:8: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/fintek-cir.c: In function 'fintek_config_mode_enable':
drivers/media/rc/fintek-cir.c:80:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/fintek-cir.c:81:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/fintek-cir.c: In function 'fintek_config_mode_disable':
drivers/media/rc/fintek-cir.c:87:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/nuvoton-cir.c: In function 'nvt_cr_write':
drivers/media/rc/nuvoton-cir.c:45:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/nuvoton-cir.c:46:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/nuvoton-cir.c: In function 'nvt_cr_read':
drivers/media/rc/nuvoton-cir.c:52:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/nuvoton-cir.c:53:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/nuvoton-cir.c: In function 'nvt_efm_enable':
drivers/media/rc/nuvoton-cir.c:74:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/nuvoton-cir.c:75:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/nuvoton-cir.c: In function 'nvt_efm_disable':
drivers/media/rc/nuvoton-cir.c:81:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/nuvoton-cir.c: In function 'nvt_select_logical_dev':
drivers/media/rc/nuvoton-cir.c:91:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/nuvoton-cir.c:92:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Those are caused because the I/O port is u32, instead of u8.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
on ia64, those warnings appear:
drivers/media/radio/si470x/radio-si470x-i2c.c:470:12: warning: 'si470x_i2c_suspend' defined but not used [-Wunused-function]
drivers/media/radio/si470x/radio-si470x-i2c.c:487:12: warning: 'si470x_i2c_resume' defined but not used [-Wunused-function]
They're caused because the PM logic uses this define:
#define SET_SYSTEM_SLEEP_PM_OPS()
With is only defined for CONFIG_PM_SLEEP.
So, change the logic there to test for CONFIG_PM_SLEEP, instead of
CONFIG_PM.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Simplify the logic that calculates the carrier, and removes a warning
on avr32 arch:
drivers/media/rc/iguanair.c: In function 'iguanair_set_tx_carrier':
drivers/media/rc/iguanair.c:304: warning: 'sevens' may be used uninitialized in this function
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On avr32 arch, we get those warnings:
drivers/media/radio/tef6862.c:59:1: warning: "MODE_SHIFT" redefined
In file included from /devel/v4l/ktest-build/arch/avr32/include/asm/ptrace.h:11,
arch/avr32/include/uapi/asm/ptrace.h:41:1: warning: this is the location of the previous definition
Prefix MSA_ to the MSA register bitmap macros, to avoid reusing the same symbol.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/pci/cx18/cx18-driver.c: In function 'cx18_read_eeprom':
drivers/media/pci/cx18/cx18-driver.c:357:1: warning: the frame size of 1072 bytes is larger than 1024 bytes [-Wframe-larger-than=]
That happens because the routine allocates 256 bytes for an eeprom buffer, plus
the size of struct i2c_client, with is big.
Change the logic to dynamically allocate/deallocate space for struct i2c_client,
instead of using the stack.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This driver uses virt_to_bus() with is deprecated on Alpha:
drivers/media/pci/zoran/zoran_device.c: In function 'zr36057_set_vfe':
drivers/media/pci/zoran/zoran_device.c:451:3: warning: 'virt_to_bus' is deprecated (declared at /devel/v4l/ktest-build/arch/alpha/include/asm/io.h:114) [-Wdeprecated-declarations]
drivers/media/pci/zoran/zoran_device.c:453:3: warning: 'virt_to_bus' is deprecated (declared at /devel/v4l/ktest-build/arch/alpha/include/asm/io.h:114) [-Wdeprecated-declarations]
drivers/media/pci/zoran/zoran_device.c: In function 'zr36057_set_jpg':
drivers/media/pci/zoran/zoran_device.c:796:2: warning: 'virt_to_bus' is deprecated (declared at /devel/v4l/ktest-build/arch/alpha/include/asm/io.h:114) [-Wdeprecated-declarations]
drivers/media/pci/zoran/zoran_driver.c: In function 'v4l_fbuffer_alloc':
drivers/media/pci/zoran/zoran_driver.c:241:3: warning: 'virt_to_bus' is deprecated (declared at /devel/v4l/ktest-build/arch/alpha/include/asm/io.h:114) [-Wdeprecated-declarations]
drivers/media/pci/zoran/zoran_driver.c:245:3: warning: 'virt_to_bus' is deprecated (declared at /devel/v4l/ktest-build/arch/alpha/include/asm/io.h:114) [-Wdeprecated-declarations]
drivers/media/pci/zoran/zoran_driver.c: In function 'jpg_fbuffer_alloc':
drivers/media/pci/zoran/zoran_driver.c:334:3: warning: 'virt_to_bus' is deprecated (declared at /devel/v4l/ktest-build/arch/alpha/include/asm/io.h:114) [-Wdeprecated-declarations]
drivers/media/pci/zoran/zoran_driver.c:347:5: warning: 'virt_to_bus' is deprecated (declared at /devel/v4l/ktest-build/arch/alpha/include/asm/io.h:114) [-Wdeprecated-declarations]
drivers/media/pci/zoran/zoran_driver.c:366:6: warning: 'virt_to_bus' is deprecated (declared at /devel/v4l/ktest-build/arch/alpha/include/asm/io.h:114) [-Wdeprecated-declarations]
As we're not even sure if it works on Alpha, better to just disable its compilation there.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On alpha, allyesconfig doesn't have CONFIG_PM, and produces the following warnings:
drivers/media/radio/radio-shark.c:274:13: warning: 'shark_resume_leds' defined but not used [-Wunused-function]
drivers/media/radio/radio-shark2.c:240:13: warning: 'shark_resume_leds' defined but not used [-Wunused-function]
That's because those functions are used only at device resume.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There's no need to zero the buffer, as if the routine gets an error,
rc will be different than one.
That fixes the following warning:
drivers/media/tuners/tda9887.c: In function 'tda9887_status':
drivers/media/tuners/tda9887.c:539:2: warning: value computed is not used [-Wunused-value]
While here, make fix the CodingStyle on this function.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Here's the big USB driver update for 3.13-rc1.
It includes the usual xhci changes, EHCI updates to get the scheduling
of USB transactions working better, and a raft of gadget and musb
updates as well.
All of this has been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJ6xycACgkQMUfUDdst+ymO+gCgxXdQXSU23i9ykc2CKBemdEBH
w6IAoKcokITcdN1IxxkfiMxOEld2hgZm
=3kbb
-----END PGP SIGNATURE-----
Merge tag 'usb-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver update from Greg KH:
"Here's the big USB driver update for 3.13-rc1.
It includes the usual xhci changes, EHCI updates to get the scheduling
of USB transactions working better, and a raft of gadget and musb
updates as well.
All of this has been in linux-next for a while with no reported
issues"
* tag 'usb-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (305 commits)
USB: Maintainers change for usb serial drivers
usb: usbtest: support container id descriptor test
usb: usbtest: support superspeed device capbility descriptor test
usb: usbtest: support usb2 extension descriptor test
usb: chipidea: only get vbus regulator for non-peripheral mode
USB: ehci-atmel: add usb_clk for transition to CCF
usb: cdc-wdm: ignore speed change notifications
USB: cdc-wdm: support back-to-back USB_CDC_NOTIFY_RESPONSE_AVAILABLE notifications
usbatm: Fix dynamic_debug / ratelimited atm_dbg and atm_rldbg macros
printk: pr_debug_ratelimited: check state first to reduce "callbacks suppressed" messages
usb: usbtest: support bos descriptor test for usb 3.0
USB: phy: samsung: Support multiple PHYs of same type
usb: wusbcore: change WA_SEGS_MAX to a legal value
usb: wusbcore: add a quirk for Alereon HWA device isoc behavior
usb: wusbcore: combine multiple isoc frames in a single transfer request.
usb: wusbcore: set the RPIPE wMaxPacketSize value correctly
usb: chipidea: host: more enhancement when ci->hcd is NULL
usb: ohci: remove ep93xx bus glue platform driver
usb: usbtest: fix checkpatch warning as sizeof code style
UWB: clean up attribute use by using ATTRIBUTE_GROUPS()
...
The code sequence:
isp->raw_dmamask = DMA_BIT_MASK(32);
isp->dev->dma_mask = &isp->raw_dmamask;
isp->dev->coherent_dma_mask = DMA_BIT_MASK(32);
bypasses the architectures check on the DMA mask. It can be replaced
with dma_coerce_mask_and_coherent(), avoiding the direct initialization
of this mask.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support to ST RC driver, which is basically a IR/UHF
receiver and transmitter. This IP (IRB) is common across all the ST
parts for settop box platforms. IRB is embedded in ST COMMS IP block.
It supports both Rx & Tx functionality.
This driver adds only Rx functionality via LIRC codec.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adds the driver for the LM3560, dual LED Flash The LM3560 has two 1A
constant current driver for high current white LEDs.
It is controlled via an I2C compatible interface(up to 400kHz).
Each flash brightness, torch brightness and enable/disable can be
controlled independantly, but flash timeout and operation mode are shared.
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Components are RTL2832P + R828D + MN88472.
Currently support only DVB-T as there is no driver for MN88472 demod.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
RTL2832P is version of RTL2832U with extra TS interface.
As for now, we support only integrated RTL2832 demod.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use R820T config for R828D too as those are about same tuner.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Small changes in order to support tuner version R828D @ 16 MHz clock.
There was 'vco_fine_tune' check, which seems to adjust synthesizer
output divider (mixer dix / LO div / Rout) by one. R828D seems to
return vco_fine_tune=1 every time and that condition causes tuning
fail as output divider was increased by one.
Resolve problem by skipping whole condition in case of R828D tuner.
Just to mention, other tuner, R820T, seems to return 2 here.
Synthesizer maximum frequency check was hard coded to check synthesizer N
and thus worked correctly only for clock frequencies around 30 MHz.
As whole test is quite useless in any case, I removed it totally.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
v3.12-rc fails to build with this error:
drivers/media/i2c/ths8200.c:49:2: error: unknown field 'bt' specified in initializer
drivers/media/i2c/ths8200.c:50:3: error: field name not in record or union initializer
drivers/media/i2c/ths8200.c:50:3: error: (near initialization for 'ths8200_timings_cap.reserved')
drivers/media/i2c/ths8200.c:51:3: error: field name not in record or union initializer
drivers/media/i2c/ths8200.c:51:3: error: (near initialization for 'ths8200_timings_cap.reserved')
...
with gcc 4.5.4. This error was not detected in builds prior to v3.12-rc.
This patch fixes this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: stable@vger.kernel.org # For kernel v3.12
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds support for the UB435-Q V2. You might need to
use the device once with the Windows driver provided by KWorld
in order to permanently reprogram the device descriptors. Thanks
to Jarod Wilson for the initial attempt at adding support for this
device.
[m.chehab@samsung.com: Fixed Whitespace mangling, Coding Style and
improved the error handling at DVB attach]
Signed-off-by: Jean-Francois Thibert <jfthibert@google.com>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
i2c_adap is a field of a struct and will always be allocated so
its address will never be null.
Suggested by coccinelle, manually verified.
Signed-off-by: Alexandru Juncu <alexj@rosedu.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The em28xx driver only calls subdevices' .s_power() method to power them
down, relying on the hardware to wake up automatically, which is usually
the case with tuners. This was acceptable with the old .standby() method,
but is wrong with .s_power(). Fixing the driver would be difficult due to
a broad supported hardware base. Instead this patch makes use of the
unbalanced_power soc-camera subdevice flag to tell the ov2640 driver to
balance calls to v4l2_clk_enable() and v4l2_clk_disable() internally.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some non soc-camera drivers, e.g. em28xx, use subdevice drivers, originally
written for soc-camera, which use soc_camera_power_on() and
soc_camera_power_off() helpers to implement their .s_power() methods. Those
helpers in turn can enable and disable a clock, if it is supplied to them
as a parameter. This works well when camera host drivers balance their
calls to subdevices' .s_power() methods. However, some such drivers fail to
do that, which leads to unbalanced calls to v4l2_clk_enable() /
v4l2_clk_disable(), which then in turn produce kernel warnings. Such
behaviour is wrong and should be fixed, however, sometimes it is difficult,
because some of those drivers are rather old and use lots of subdevices,
which all should be tested after such a fix. To support such drivers this
patch adds a work-around, allowing host drivers or platforms to set a flag,
in which case soc-camera helpers will only enable the clock, if it is
disabled, and disable it only once on the first call to .s_power(0).
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Camera sensors usually require a master clock for data sampling. This patch
registers such a clock source for em28xx cameras. This fixes the currently
broken em28xx ov2640 camera support and can also be used by other camera
sensors.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Many bridges and video host controllers supply fixed rate always on clocks
to their I2C devices. This patch adds two simple helpers to register and
unregister such a clock.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This prepares soc-camera to use struct v4l2_subdev_platform_data for its
subdevice-facing API, which would allow subdevice driver re-use.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If a frame is still decoding when system enters suspend mode, we wait
on the device queue for a interrupt condition. This sometimes leads to a
timeout because the device queue might not be woken up everytime.
Usually, the context queue gets woken up when that context's frame gets
decoded. This patch adds a condition to wake up the device queue along
with the context queue when the system is in suspend mode.
Since the device queue is now woken up, we don't have to check the
context's int_cond flag while waiting. Also, we can skip calling try_run
after waking up the device queue to ensure that we don't have to wait
for more than one frame to be processed.
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Arun Mankuzhi <arun.m@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The patch sets the default values of MAX_QP and GOP size encoder
parameters to some firmware recommended default values. This enables
the applications to get a better encoded output using the default
settings itself.
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Running the coda driver without CONFIG_SRAM selected leads to the following
probe error:
coda 63ff4000.vpu: iram pool not available
coda: probe of 63ff4000.vpu failed with error -12
In order to avoid it, select CONFIG_SRAM inside VIDEO_CODA.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If unused, the pixel format priv field has to be cleared by the driver
in try_fmt.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement try_decoder_cmd to let userspace determine available commands
and flags.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch fixes the v4l2-compliance "TRY_FMT(G_FMT) != G_FMT" issue.
The driver now overwrites invalid formats with the current setting, using
coda_get_max_dimensions to find device specific max width/height.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Moving the ioctl handler callbacks into the coda namespace helps
tremendously to make sense of backtraces.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[k.debski@samsung.com: fix whitespace error near coda_subscribe_event]
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of copying v4l2_buf.flags from the source buffer, set
the destination buffer flags as reported by the hardware codec.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the product name (currently CodaDx6 or CODA7541)
to fill the v4l2_capabilities.name field.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The register is only written on CodaDx6, so the temporary variable
to be written only needs to be initialized on CodaDx6. Also, drop
two no-op lines.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Allow device_run with no buffers queued after streamoff only when
the current instance is a decoder.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[k.debski@samsung.com: Add commit description]
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
With the new firmware, there are not anymore four register sets,
but a single register set, which the driver has to conserve across
context switches. This allows to handle more than four instances
at the same time.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the current context is running,
1] If release is called, it waits until the job is finished.
2] As soon as the job is finished, v4l2_mem_ctx_release()tries to
release the vb2 queues.
3] But if the current context can be scheduled in the v4l2_m2m_job_finish()
it schedules the context and tries to call device_run().
4] As the release() and device_run() sequence can't be predicted sometimes
device_run() may get empty vb2 buffers.
This patch adds the ABORT state to the job_flags. Once the job_abort() or
release() is called on the context, the same context will not be scheduled in
the v4l2_m2m_job_finish().
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the current context is running,
1] If release() or streamoff() is called on the current context,
it waits until the job is aborted or finished.
2] If the job is finished, driver will call the v4l2_m2m_job_finish().
3] If the job is aborted inside device_run callback, then driver
has to inform the v4l2 mem2mem framework about the same by calling
v4l2_m2m_job_finish() with VB2_BUF_STATE_ERROR.
The current code doesn't call v4l2_m2m_job_finish() in the case, where
the job is aborted from the device_run callback. This scenerio is
producing a hang as the other queued contexts are not getting scheduled.
By adding the ABORT state, driver can understand the current job
is aborted and not finished. By checking this flag, driver can call
v4l2_m2m_job_finish() with VB2_BUF_STATE_ERROR.
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Avnd Kiran <avnd.kiran@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
v4l2_m2m_streamoff drops the list of ready buffers but failed to reset the
num_rdy counter to zero. This would lead to v4l2_m2m_num_src/dst_bufs_ready
reporting wrong values after streamoff.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Just clearing the m2m_ctx->queue list_head will leave the m2m_dev->job_queue
in a broken state and can cause scheduling of device_runs after streamoff was
called.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for the de-interlacer block in VPE. For de-interlacer to
work, we need to enable 2 more sets of VPE input ports which fetch data
from the 'last' and 'last to last' fields of the interlaced video. Apart
from that, we need to enable the Motion vector output and input ports,
and also allocate DMA buffers for them.
We need to make sure that two most recent fields in the source queue are
available and in the 'READY' state. Once a mem2mem context gets access
to the VPE HW(in device_run), it extracts the addresses of the 3
buffers, and provides it to the data descriptors for the 3 sets of input
ports((LUMA1, CHROMA1), (LUMA2, CHROMA2), and (LUMA3, CHROMA3))
respectively for the 3 consecutive fields. The motion vector and output
port descriptors are configured and the list is submitted to VPDMA.
Once the transaction is done, the v4l2 buffer corresponding to the
oldest field(the 3rd one) is changed to the state 'DONE', and the
buffers corresponding to 1st and 2nd fields become the 2nd and 3rd field
for the next de-interlace operation. This way, for each deinterlace
operation, we have the 3 most recent fields. After each transaction, we
also swap the motion vector buffers, the new input motion vector buffer
contains the resultant motion information of all the previous frames,
and the new output motion vector buffer will be used to hold the updated
motion vector to capture the motion changes in the next field. The
motion vector buffers are allocated using the DMA allocation API.
The de-interlacer is removed from bypass mode, it requires some extra
default configurations which are now added. The chrominance upsampler
coefficients are added for interlaced frames. Some VPDMA parameters like
frame start event and line mode are configured for the 2 extra sets of
input ports.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VPE is a block which consists of a single memory to memory path which
can perform chrominance up/down sampling, de-interlacing, scaling, and
color space conversion of raster or tiled YUV420 coplanar, YUV422
coplanar or YUV422 interleaved video formats.
We create a mem2mem driver based primarily on the mem2mem-testdev
example. The de-interlacer, scaler and color space converter are all
bypassed for now to keep the driver simple. Chroma up/down sampler
blocks are implemented, so conversion beteen different YUV formats is
possible.
Each mem2mem context allocates a buffer for VPE MMR values which it will
use when it gets access to the VPE HW via the mem2mem queue, it also
allocates a VPDMA descriptor list to which configuration and data
descriptors are added.
Based on the information received via v4l2 ioctls for the source and
destination queues, the driver configures the values for the MMRs, and
stores them in the buffer. There are also some VPDMA parameters like
frame start and line mode which needs to be configured, these are
configured by direct register writes via the VPDMA helper functions.
The driver's device_run() mem2mem op will add each descriptor based on
how the source and destination queues are set up for the given ctx, once
the list is prepared, it's submitted to VPDMA, these descriptors when
parsed by VPDMA will upload MMR registers, start DMA of video buffers on
the various input and output clients/ports.
When the list is parsed completely(and the DMAs on all the output ports
done), an interrupt is generated which we use to notify that the source
and destination buffers are done. The rest of the driver is quite
similar to other mem2mem drivers, we use the multiplane v4l2 ioctls as
the HW support coplanar formats.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Create functions which the VPE driver can use to create a VPDMA
descriptor and add it to a VPDMA descriptor list. These functions take a
pointer to an existing list, and append the configuration/data/control
descriptor header to the list.
In the case of configuration descriptors, the creation of a payload
block may be required(the payloads can hold VPE MMR values, or scaler
coefficients). The allocation of the payload buffer and it's content is
left to the VPE driver. However, the VPDMA library provides helper
macros to create payload in the correct format.
Add debug functions to dump the descriptors in a way such that it's easy
to see the values of different fields in the descriptors.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The primary function of VPDMA is to move data between external memory
and internal processing modules(in our case, VPE) that source or sink
data. VPDMA is capable of buffering this data and then delivering the
data as demanded to the modules as programmed. The modules that source
or sink data are referred to as clients or ports. A channel is setup
inside the VPDMA to connect a specific memory buffer to a specific
client. The VPDMA centralizes the DMA control functions and buffering
required to allow all the clients to minimize the effect of long latency
times.
Add the following to the VPDMA helper:
- A data struct which describe VPDMA channels. For now, these channels
are the ones used only by VPE, the list of channels will increase when
VIP(Video Input Port) also uses the VPDMA library. This channel
information will be used to populate fields required by data
descriptors.
- Data structs which describe the different data types supported by
VPDMA. This data type information will be used to populate fields
required by data descriptors and used by the VPE driver to map a V4L2
format to the corresponding VPDMA data type.
- Provide VPDMA register offset definitions, functions to read, write
and modify VPDMA registers.
- Functions to create and submit a VPDMA list. A list is a group of
descriptors that makes up a set of DMA transfers that need to be
completed. Each descriptor will either perform a DMA transaction to
fetch input buffers and write to output buffers(data descriptors), or
configure the MMRs of sub blocks of VPE(configuration descriptors), or
provide control information to VPDMA (control descriptors).
- Functions to allocate, map and unmap buffers needed for the descriptor
list, payloads containing MMR values and scaler coefficients. These use
the DMA mapping APIs to ensure exclusive access to VPDMA.
- Functions to enable VPDMA interrupts. VPDMA can trigger an interrupt
on the VPE interrupt line when a descriptor list is parsed completely
and the DMA transactions are completed. This requires masking the events
in VPDMA registers and configuring some top level VPE interrupt
registers.
- Enable some VPDMA specific parameters: frame start event(when to start
DMA for a client) and line mode(whether each line fetched should be
mirrored or not).
- Function to load firmware required by VPDMA. VPDMA requires a firmware
for it's internal list manager. We add the required request_firmware
apis to fetch this firmware from user space.
- Function to dump VPDMA registers.
- A function to initialize and create a VPDMA instance, this will be
called by the VPE driver with it's platform device pointer, this
function will take care of loading VPDMA firmware and returning a
vpdma_data instance back to the VPE driver. The VIP driver will also
call the same init function to initialize it's own VPDMA instance.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
nobody else will see that struct file after return from ->release()
anyway; just leave ->f_op as is and let __fput() do that fops_put().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
irq allocated with devm_request_irq should not be freed using
free_irq, because doing so causes a dangling pointer, and a
subsequent double free.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some architectures do not support PCI, but still support USB, so need
let our usb driver try to use usb_* instead of pci_* to support these
architectures, or can not pass compiling.
The related error (with allmodconfig for arc):
CC [M] drivers/media/usb/b2c2/flexcop-usb.o
drivers/media/usb/b2c2/flexcop-usb.c: In function ‘flexcop_usb_transfer_exit’:
drivers/media/usb/b2c2/flexcop-usb.c:393: error: implicit declaration of function ‘pci_free_consistent’
drivers/media/usb/b2c2/flexcop-usb.c: In function ‘flexcop_usb_transfer_init’:
drivers/media/usb/b2c2/flexcop-usb.c:410: error: implicit declaration of function ‘pci_alloc_consistent’
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The variable frame_ready is only assigned the values true and false.
Change its type to bool.
The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):
@exists@
type T;
identifier b;
@@
- T
+ bool
b = ...;
... when any
b = \(true\|false\)
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
__setup_offsets fills the v4l2_planes' mem_offset fields, which is only valid
for V4L2_MEMORY_MMAP type buffers. For V4L2_MEMORY_DMABUF and _USERPTR buffers,
this incorrectly overwrites the fd and userptr fields.
Reported-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The pan/tilt absolute control value is signed value. If minimum value
is minus, It will be changed to plus by clamp_t() as commit 64ae9958a6.
([media] uvcvideo: Fix control value clamping for unsigned integer controls).
It leads to wrong setting of the control values. For example,
when min and max are -36000 and 36000, the setting value between of this range
is always 36000. So, its data type should be changed to signed.
Signed-off-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/pci/cx25821/cx25821-cards.c:49:20: warning: symbol 'cx25821_bcount' was not declared. Should it be static?
drivers/media/pci/cx25821/cx25821-video-upstream.c:162:33: warning: incorrect type in assignment (different base types)
drivers/media/pci/cx25821/cx25821-video-upstream.c:163:33: warning: incorrect type in assignment (different base types)
drivers/media/pci/cx25821/cx25821-video-upstream.c:164:33: warning: incorrect type in assignment (different base types)
drivers/media/pci/cx25821/cx25821-video-upstream.c:165:33: warning: incorrect type in assignment (different base types)
drivers/media/pci/cx25821/cx25821-medusa-video.h:43:16: warning: symbol '_num_decoders' was not declared. Should it be static?
drivers/media/pci/cx25821/cx25821-medusa-video.h:44:16: warning: symbol '_num_cameras' was not declared. Should it be static?
drivers/media/pci/cx25821/cx25821-medusa-video.h:46:14: warning: symbol '_video_standard' was not declared. Should it be static?
drivers/media/pci/cx25821/cx25821-medusa-video.h:47:5: warning: symbol '_display_field_cnt' was not declared. Should it be static?
After analyzing the last four warnings carefully it became clear that these
variables were really completely unused. As a result of that the call to
medusa_set_decoderduration() is now dubious since the duration is always 0.
Without documentation, however, I can't tell what the right value is.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove the redundant 'const' qualifiers from the function
signature and from the qmenu_int arrays' declarations.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Increase the streaming_users count only if streaming start succeeds.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix CodingStyle on the GPIO init tables.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are numerous issues in error handling code of cx231xx initialization.
Double free (when cx231xx_init_dev() calls kfree(dev) via cx231xx_release_resources()
and then cx231xx_usb_probe() does the same) and memory leaks
(e.g. usb_get_dev() before (ifnum != 1) check in cx231xx_usb_probe())
are just a few of them.
The patch fixes the issues in cx231xx_usb_probe() and cx231xx_init_dev()
by moving usb_get_dev(interface_to_usbdev(interface)) below in code and
implementing proper error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
module_pci_driver removes some boilerplate and makes code simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/common/siano/smsdvb-main.c:47:5: warning: symbol 'sms_to_guard_interval_table' was not declared. Should it be static?
drivers/media/common/siano/smsdvb-main.c:54:5: warning: symbol 'sms_to_code_rate_table' was not declared. Should it be static?
drivers/media/common/siano/smsdvb-main.c:63:5: warning: symbol 'sms_to_hierarchy_table' was not declared. Should it be static?
drivers/media/common/siano/smsdvb-main.c:70:5: warning: symbol 'sms_to_modulation_table' was not declared. Should it be static?
drivers/media/common/siano/smscoreapi.c:925:35: warning: cast to restricted __le32
drivers/media/common/siano/smscoreapi.c:926:28: warning: cast to restricted __le32
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/usb/dvb-usb/az6027.c:257:23: warning: symbol 'az6027_stb0899_config' was not declared. Should it be static?
drivers/media/usb/dvb-usb/az6027.c:294:23: warning: symbol 'az6027_stb6100_config' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/drxk_hard.c:1086:62: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drxk_hard.c:2784:63: warning: Using plain integer as NULL pointer
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/drxd_hard.c:1017:70: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drxd_hard.c:1038:69: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drxd_hard.c:2836:33: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drxd_hard.c:2972:30: warning: Using plain integer as NULL pointer
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
These aren't necessary after switch and while statements.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the generic PHY API instead of the platform callback
to control the MIPI CSIS DPHY.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/media/usb/tlg2300/pd-main.c:235:25: warning: incorrect type in assignment (different base types)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/usb/cx231xx/cx231xx-pcb-cfg.c:31:19: warning: symbol 'cx231xx_Scenario' was not declared. Should it be static?
drivers/media/usb/cx231xx/cx231xx-pcb-cfg.c:675:23: warning: cast to restricted __le32
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/radio/wl128x/fmdrv_common.c:178:6: warning: symbol 'g_st_write' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/usb/pvrusb2/pvrusb2-hdw.c:2871:13: warning: symbol 'pvr2_hdw_get_detected_std' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dear Hans de Goede, I have Ubuntu (raring) and recently bought digital
microscope eyepiece Lomo MD300. It is the same device as Future Optics MVV3000.
Unfortunately it does not work out of box. Moreover drivers refused to work
under Windows 7 as well leaving me only with Win Xp working system. I have had
no choice but to examine what happened in USB bus and attempt to reproduce the
sequence. So, i have download the source(3.8.0-30 kernel) and made required
changes to driver to make my hardware work.
I submit my changed files to you as maintainer of the driver so you can
integrade my changes into main stream. Thanx. Hopefully my Ubuntu will work
with my hardware out of box.
Sincerely yours Vladik Aranov
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
That version of DRX-K chip supports only 2.
drxk: SCU_RESULT_INVPAR while sending cmd 0x0203 with params:
drxk: Warning -22 on qam_demodulator_command
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
tda18271c2dd => tda18271
tda18271 is more complete than tda18271c2dd.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Downloading new firmware for DRX-K demodulator is not obligatory but
usually it offers important bug fixes compared to default firmware
burned into chip rom. DRX-K demod driver will continue even without
the firmware, but in that case it will print warning to system log
to tip user he should install firmware.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Correct common misspelling of "identify" as "indentify" throughout
the kernel
Signed-off-by: Maxime Jayat <maxime@artisandeveloppeur.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Correct spelling typo within various part of the kernel
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Tested:
Composite: http://imgur.com/Rb1TCF3
TV: http://imgur.com/KNrfsmv
Firmware used: xc3028-v27.fw
Not tested: audio, component, s-video, mpeg2 encoder, FM radio.
For audio, it uses an CD style cable to connect to the analog "CD_IN" on the motherboard.
I didn't found how to unmute it (alsamixer do not show an CD or AUX channel).
Signed-off-by: Anca Emanuel <anca.emanuel@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The Stellar firmware load routine is different. Improve it to use
the default firmware, if no modprobe parameter tells otherwise.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tested-by: André Roth <neolynx@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since kernel 3.8, the initialization for Stellar (sms1000)
devices are broken.
Those devices have a behaviour different than usual sms1100
and sms2270: they start with one USB ID (devices in cold state),
but after firmware load, they get a different USB ID.
This weren't docummented at the driver. So, the patches that added
support for sms2270 broke it.
Properly documment it, and provide a debug log that allows to
follow all phases of the device initialization:
smsusb_probe: board id=13, interface number 0
smsusb_probe: interface 0 won't be used. Expecting interface 1 to popup
smsusb_probe: board id=13, interface number 1
smsusb_probe: smsusb_probe 1
smsusb_probe: endpoint 0 81 02 64
smsusb_probe: endpoint 1 02 02 64
smsusb_probe: stellar device in cold state was found at usb\4-2.
smsusb1_load_firmware: sent 38144(38144) bytes, rc 0
smsusb1_load_firmware: read FW dvbt_bda_stellar_usb.inp, size=38144
smsusb_probe: stellar device now in warm state
usbcore: registered new interface driver smsusb
usb 4-2: USB disconnect, device number 52
usb 4-2: new full-speed USB device number 53 using uhci_hcd
usb 4-2: New USB device found, idVendor=187f, idProduct=0100
usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 4-2: Product: SMS DVBT-BDA Receiver
usb 4-2: Manufacturer: Siano Mobile Silicon
smsusb_probe: board id=1, interface number 0
smsusb_probe: smsusb_probe 0
smsusb_probe: endpoint 0 81 02 64
smsusb_probe: endpoint 1 02 02 64
smsusb_init_device: in_ep = 81, out_ep = 02
smscore_register_device: allocated 50 buffers
smscore_register_device: device ffff88012a00bc00 created
smsusb_init_device: smsusb_start_streaming(...).
smscore_set_device_mode: set device mode to 4
smsusb1_detectmode: 4 "SMS DVBT-BDA Receiver"
smsusb_sendrequest: sending MSG_SMS_INIT_DEVICE_REQ(578) size: 12
smsusb_onresponse: received MSG_SMS_INIT_DEVICE_RES(579) size: 12
smscore_set_device_mode: Success setting device mode.
smscore_init_ir: IR port has not been detected
smscore_start_device: device ffff88012a00bc00 started, rc 0
smsusb_init_device: device 0xffff88002cfa6000 created
smsusb_probe: Device initialized with return code 0
DVB: registering new adapter (Siano Stellar Digital Receiver)
usb 4-2: DVB: registering adapter 0 frontend 0 (Siano Mobile Digital MDTV Receiver)...
smscore_register_client: ffff88012174a000 693 1
sms_board_dvb3_event: DVB3_EVENT_HOTPLUG
smsdvb_hotplug: success
smsdvb_module_init:
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tested-by: André Roth <neolynx@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some messages are not clear, some are debug data, but are
shown as errors, and one message is duplicated.
Cleanup that mess in order to provide a cleaner log.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tested-by: André Roth <neolynx@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
At this bugzilla and similar ones:
https://bugzilla.kernel.org/show_bug.cgi?id=60645
Those debug messages were seen as errors, but they're just debug
data, and are OK to appear on sms1100 and sms2270. Re-tag them
to appear only if debug is enabled.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tested-by: André Roth <neolynx@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch will fix the situation where the mutex was left in a
locked state if for some reason the FE init failed.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
pm_qos_remove_request was not called on video_release, resulting in the PM
core's list of requests being corrupted when the file handle was freed.
This has no immediate symptoms, but later in operation, the kernel will
panic as the PM core dereferences a dangling pointer.
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix to return -ENOMEM in the new i2c client and create workqueue error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The "|" operation has higher precedence that "?:" so this couldn't
return both flags set at once as intended.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Since CONFIG_PLAT_S3C64XX is going to be removed, this patch modifies
the Kconfig entry of s3c-camif driver to use the proper way of checking
for S3C64xx support - CONFIG_ARCH_S3C64XX.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The 'driver' field of the i2c_client struct is redundant and is going to be
removed. The results of the expressions 'client->driver.driver->field' and
'client->dev.driver->field' are identical, so replace all occurrences of the
former with the later.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The 'driver' field of the i2c_client struct is redundant and is going to be
removed. The results of the expressions 'client->driver.driver->field' and
'client->dev.driver->field' are identical, so replace all occurrences of the
former with the later.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The 'driver' field of the i2c_client struct is redundant and is going to be
removed. The results of the expressions 'client->driver.driver->field' and
'client->dev.driver->field' are identical, so replace all occurrences of the
former with the later.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix to return -ENOMEM in the new i2c client and create workqueue error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
