Add routines to converts dmtimers to platform devices. The device data
is obtained from hwmod database of respective platform and is registered
to device model after successful binding to driver.
In addition, capability attribute of each of the timers is added in
hwmod database.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Thara Gopinath <thara@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert OMAP1 dmtimers into a platform devices and then registers with
device model framework so that it can be bound to corresponding driver.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device name to OMAP2 dmtimer fclk nodes so that the fclk nodes can be
retrieved by doing a clk_get with the corresponding device pointers or
device names.
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Thara Gopinath <thara@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
[tony@atomide.com: fixed typo in email address]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add omap_device pointer to the ARM-specific arch data in the
platform_device. This will be used to attach OMAP-specific
device-data to the platform device with device lifetime.
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Even when CONFIG_PM=n, we try to scale the boot voltage to a sane,
known value using OPP table to find matching voltage based on boot
frequency. This should be done, even when CONFIG_PM=n to avoid
mis-configured bootloaders and/or boot voltage assumptions made by
boot loaders.
Also fixes various compile problems due to depenencies between voltage
domain and powerdomain code (also present when CONFIG_PM=n).
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Commit f41caddbe7 (omap2+: Use
Kconfig symbol in Makefile instead of obj-y) cleaned up the
omap2+ Makefile. However this did not account for the inline
functions that are now needed for board_flash_init and
board_nand_init.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are seeing linker errors caused by sections being discarded, despite
the linker script trying to keep them. The result is (eg):
`.exit.text' referenced in section `.alt.smp.init' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o
`.exit.text' referenced in section `.alt.smp.init' of net/built-in.o: defined in discarded section `.exit.text' of net/built-in.o
This is the relevent part of the linker script (reformatted to make it
clearer):
| SECTIONS
| {
| /*
| * unwind exit sections must be discarded before the rest of the
| * unwind sections get included.
| */
| /DISCARD/ : {
| *(.ARM.exidx.exit.text)
| *(.ARM.extab.exit.text)
| }
| ...
| .exit.text : {
| *(.exit.text)
| *(.memexit.text)
| }
| ...
| /DISCARD/ : {
| *(.exit.text)
| *(.memexit.text)
| *(.exit.data)
| *(.memexit.data)
| *(.memexit.rodata)
| *(.exitcall.exit)
| *(.discard)
| *(.discard.*)
| }
| }
Now, this is what the linker manual says about discarded output sections:
| The special output section name `/DISCARD/' may be used to discard
| input sections. Any input sections which are assigned to an output
| section named `/DISCARD/' are not included in the output file.
No questions, no exceptions. It doesn't say "unless they are listed
before the /DISCARD/ section." Now, this is what asn-generic/vmlinux.lds.S
says:
| /*
| * Default discarded sections.
| *
| * Some archs want to discard exit text/data at runtime rather than
| * link time due to cross-section references such as alt instructions,
| * bug table, eh_frame, etc. DISCARDS must be the last of output
| * section definitions so that such archs put those in earlier section
| * definitions.
| */
And guess what - the list _always_ includes .exit.text etc.
Now, what's actually happening is that the linker is reading the script,
and it finds the first /DISCARD/ output section at the beginning of the
script. It continues reading the script, and finds the 'DISCARD' macro
at the end, which having been postprocessed results in another
/DISCARD/ output section. As the linker already contains the earlier
/DISCARD/ output section, it adds it to that existing section, so it
effectively is placed at the start. This can be seen by using the -M
option to ld:
| Linker script and memory map
|
| 0xc037c080 jiffies = jiffies_64
|
| /DISCARD/
| *(.ARM.exidx.exit.text)
| *(.ARM.extab.exit.text)
| *(.exit.text)
| *(.memexit.text)
| *(.exit.data)
| *(.memexit.data)
| *(.memexit.rodata)
| *(.exitcall.exit)
| *(.discard)
| *(.discard.*)
|
| 0xc0008000 . = 0xc0008000
|
| .head.text 0xc0008000 0x1d0
| 0xc0008000 _text = .
| *(.head.text)
| .head.text 0xc0008000 0x1d0 arch/arm/kernel/head.o
| 0xc0008000 stext
|
| .text 0xc0008200 0x2d78d0
| 0xc0008200 _stext = .
| 0xc0008200 __exception_text_start = .
| *(.exception.text)
| .exception.text
| ...
As you can see, all the discarded sections are grouped together - and
as a result of it being the first output section, they all appear before
any other section.
The result is that not only is the unwind information discarded (as
intended), but also the .exit.text, despite us wanting to have the
.exit.text preserved.
We can't move the unwind information elsewhere, because it'll then be
included even when we do actually discard the .exit.text (and similar)
sections.
So, work around this by avoiding the generic DISCARDS macro, and instead
conditionalize the sections to be discarded ourselves. This avoids the
ambiguity in how the linker assigns input sections to output sections,
making our script less dependent on undocumented linker behaviour.
Reported-by: Rob Herring <robherring2@gmail.com>
Tested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'fixes' of git://git.linaro.org/people/arnd/arm-soc:
mach-integrator: fix VGA base regression
arm/dt: Tegra: Update SDHCI nodes to match bindings
ARM: EXYNOS4: fix incorrect pad configuration for keypad row lines
ARM: SAMSUNG: fix to prevent declaring duplicated
ARM: SAMSUNG: fix watchdog reset issue with clk_get()
ARM: S3C64XX: Remove un-used code backlight code on SMDK6410
ARM: EXYNOS4: restart clocksource while system resumes
ARM: EXYNOS4: Fix routing timer interrupt to offline CPU
ARM: EXYNOS4: Fix return type of local_timer_setup()
ARM: EXYNOS4: Fix wrong pll type for vpll
ARM: Dove: fix second SPI initialization call
The changes introduced in commit
cc22b4c185
"ARM: set vga memory base at run-time"
Makes the Integrator/AP freeze completely. I appears that
this is due to the VGA base address being assigned at PCI
init time, while this base is needed earlier than that.
Moving the initialization of the base address to the
.map_io function solves this problem.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The bindings were recently updated to have separate properties for each
type of GPIO. Update the Device Tree source to match that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
598841ca99 ([S390] use gmap address
spaces for kvm guest images) changed kvm on s390 to use a separate
address space for kvm guests. We can now put KVM guests anywhere
in the user address mode with a size up to 8PB - as long as the
memory is 1MB-aligned. This change was done without KVM extension
capability bit.
The change was added after 3.0, but we still have a chance to add
a feature bit before 3.1 (keeping the releases in a sane state).
We use number 71 to avoid collisions with other pending kvm patches
as requested by Alexander Graf.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Avi Kivity <avi@redhat.com>
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
598841ca99 ([S390] use gmap address
spaces for kvm guest images) changed kvm to use a separate address
space for kvm guests. This address space was switched in __vcpu_run
In some cases (preemption, page fault) there is the possibility that
this address space switch is lost.
The typical symptom was a huge amount of validity intercepts or
random guest addressing exceptions.
Fix this by doing the switch in sie_loop and sie_exit and saving the
address space in the gmap structure itself. Also use the preempt
notifier.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
The registers are slightly different between v1 and v2 ip that
is available in omap4 and later for some timers.
Add support for v2 ip by mapping the interrupt related registers
separately and adding func_base for the functional registers.
Also disable dmtimer driver features on omap4 for now as
those need the hwmod conversion series to deal with enabling
the timers properly in omap_dm_timer_init.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Tested-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CALL scripts/checksyscalls.sh
<stdin>:46:1: warning: "__IGNORE_migrate_pages" redefined
In file included from <stdin>:2:
arch/arm/include/asm/unistd.h:482:1: warning: this is the location of the previous definition
This is caused because we define __IGNORE_migrate_pages to be 1, but
in the case of nommu, it's defined to be empty. Fix this by just
defining the __IGNORE_ symbols to be empty.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch implements a workaround for erratum 764369 affecting
Cortex-A9 MPCore with two or more processors (all current revisions).
Under certain timing circumstances, a data cache line maintenance
operation by MVA targeting an Inner Shareable memory region may fail to
proceed up to either the Point of Coherency or to the Point of
Unification of the system. This workaround adds a DSB instruction before
the relevant cache maintenance functions and sets a specific bit in the
diagnostic control register of the SCU.
Cc: <stable@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'stable/bug.fixes' of git://oss.oracle.com/git/kwilk/xen:
xen/i386: follow-up to "replace order-based range checking of M2P table by linear one"
xen/irq: Alter the locking to use a mutex instead of a spinlock.
xen/e820: if there is no dom0_mem=, don't tweak extra_pages.
xen: disable PV spinlocks on HVM
During the idle/suspend path, we expect the console lock to be held so
that no console output is done during/after the UARTs are idled.
However, when using the no_console_suspend argument on the
command-line, the console driver does not take the console lock. This
allows the possibility of console activity after UARTs have been
disabled.
To fix, update the current is_suspending() to also check the
console_suspend_enabled flag.
Reported-by: Abhilash Koyamangalath <abhilash.kv@ti.com>
Tested-by: Abhilash Koyamangalath <abhilash.kv@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Rather than embedding a struct platform_device inside a struct
omap_device, decouple them, leaving only a pointer to the
platform_device inside the omap_device.
Use the arch-specific data field of the platform_device (pdev_archdata)
to add an omap_device pointer after the platform_device has been created.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Public omap_device functions need to take platform_device pointers,
conversion to omap_device pointers is done internal to the omap_device
layer.
Signed-off-by: Kevin Hilman <khilman@ti.com>
The internal device register functions do not need or use any omap_device
internals, so pass in a platform_device pointer instead of an omap_device
pointer.
Signed-off-by: Kevin Hilman <khilman@ti.com>
All of the device init and device driver interaction with omap_device
is done using platform_device pointers. To make this more explicit,
have omap_device return a platform_device pointer instead of an
omap_device pointer.
All current users of the omap_device pointer were only using it to get
at the platform_device pointer or struct device pointer, so fixing all
of the users was trivial.
This also makes it more difficult for device init code to directly
access members of struct omap_device, and allows for easier changing
of omap_device internals.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The *_device_register() functions and the count/fill resources functions
are internal to omap_device and do not need to be in the header.
Signed-off-by: Kevin Hilman <khilman@ti.com>
During normal system operation warning messages similar to this
are appearing quite often:
omap_device: omap4-keypad.-1: new worst case activate latency 0: 61035
This doesn't seem to be reporting a problem, nor is it very useful for
non-developers, so reduce it to debug level.
Acked-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
For consistency in kernel printk output for devices, use dev_dbg(),
dev_warn(), dev_err() instead of pr_debug(), pr_warning() and
pr_err(), some of which currently use direct access of name from
platform_device and others of which use dev_name(). Using the dev_*
versions uses the standard device naming from the driver core.
Some pr_* prints were not converted with this patch since they are
used before the platform_device and struct device are created so
neither the dev_* prints or dev_name() is valid.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
struct omap_device *od is only set with find_omap_device_by_dev but not used
otherwise so remove them and references to omap device API.
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
On x86-64, they were just wasteful: with the explicitly added (now
unnecessary) padding, the size of the alternatives structure was 16
bytes, and an alignment of 8 bytes didn't hurt much.
However, it was still silly, since the natural size and alignment for
the structure is actually just 12 bytes, 4-byte aligned since commit
59e97e4d6f ("x86: Make alternative instruction pointers relative").
So removing the padding, and removing the extra alignment is just a good
idea.
On x86-32, the alignment of 4 bytes was correct, but was incorrectly
hardcoded as 8 bytes in <asm/alternative-asm.h>. That header file had
used to be an x86-64 only header file, but various unification efforts
have made it be used for x86-32 too (ie the unification of rwlock and
rwsem).
That in turn caused x86-32 boot failures, because the extra alignment
would result in random zero-filled words in the altinstructions section,
causing oopses early at boot when doing alternative instruction
replacement.
So just remove all the alignment noise entirely. It's wrong, and it's
unnecessary. The section itself is already properly aligned by the
linker scripts, and all additions to the section had better be of the
proper 12-byte format, keeping it aligned. So if the align directive
were to ever make a difference, that would be an indication of a serious
bug to begin with.
Reported-by: Werner Landgraf <w.landgraf@ru.r>
Acked-by: Andrew Lutomirski <luto@mit.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to latest OMAP4430 Data Manual v0.4 dated March 2011:
- Retention voltage shall be set to 0.83V. See tables 2.2, 2.4 and 2.6 in DM.
This allows saving a little more power in retention states.
- OPP100 IVA nominal voltage is 1.188V. See table 2.4 in DM.
This allows saving a little power when CPU wakes up until Smart-Reflex is
not yet resumed.
[nm@ti.com: ported to voltdm_c]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Patrick Titiano <p-titiano@ti.com>
using 1.35V as a check is not correct, we know that beyond 0x39,
voltages are non linear - hence use the conversion iff uV greater
than that for 0x39. For example, with 709mV as the smps offset,
the max linear is actually 1.41V(0x39vsel)!
Signed-off-by: Nishanth Menon <nm@ti.com>
omap_twl_vsel_to_uv() and omap_twl_uv_to_vsel() functions used to convert
voltages to TWL6030 SMPS commands (a.k.a "vsel") implement incorrect conversion
formula.
It uses legacy OMAP3 formula, but OMAP4 Power IC has different offset and
voltage step:
- Voltage Step is now 12.66mV (instead of 12.5mV)
- Offset is either 607.7mV or 709mV depending on TWL6030 chip revision
(instead of 600mV)
This leads to setting voltages potentially higher than expected, and so
potentially some (limited) power overconsumption.
For reference, see formula and tables in section 8.5.2.3
"Output Voltage Selection (Standard Mode / Extended Mode with or without offset)"
in TWL6030 functional specifications document.
[nm@ti.com: ported to voltdm_c]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Patrick Titiano <p-titiano@ti.com>
Needed as some of the voltage layer functionality is accessed from the
SMPS regulator driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Starting with OMAP5, the following registers are per-channel and not
common to a all VC channels:
- SMPS I2C slave address
- SMPS voltage register address offset
- SMPS cmd/value register address offset
- VC channel configuration register
Move these from the channel-common struct into the per-channel struct
to support OMAP5.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Currently, the nominal voltage is updated in the VC post-scale function
which is common to both scaling methods. However, this has readabiliy
problems as this update is not where it might be expected. Instead, move
the updated into voltdm_scale() upon a successful return of voltdm->scale()
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove last remaining member (volt_data) from omap_vdd_info into
struct voltagedomain and removal remaining usage and reference to
omap_vdd_info.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Track current nominal voltage as part of struct voltagedomain instead
of omap_vdd_info, which will soon be removed.
Also renames field from curr_volt to nominal_volt.
No functional changes.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Rename voltage scaling related functions to use voltdm_ prefix intead
of omap_voltage_, and cleanup kerneldoc comments in the process.
s/omap_voltage_scale_vdd/voltdm_scale/
s/omap_voltage_reset/voltdm_reset/
Also, in voltdm_reset() s/target_uvdc/target_volt/ to be consistent with
naming throughout the file.
No functional changes.
Signed-off-by: Kevin Hilman <khilman@ti.com>
combine VPCONFIG init voltage setup into common function and use from
both vp_enable and from vp_forceupdate_scale().
NOTE: this patch changes the sequence of when the initVDD bit is
cleared. The bit is now cleared immediately after it was written.
Since only the rising edge of this bit has any affect according to the
TRM, the exact timing of clearing of this bit should not have any
effect.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Reading the VPVOLTAGE field of PRM_VP_*_VOLTAGE registers currently
relies on a u32 -> u8 conversion to mask off the FORCEUPDATEWAIT field
in the upper bits. Make this explicit using the mask symbol
already defined, added as a new field in struct omap_vp_common.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Function pointer used for actual voltage scaling (e.g. VP force update
or VC bypass) is moved from omap_vdd_info into struct voltagedomain,
resulting in renames s/vdd->volt_scale/voltdm->scale/
No functional changes.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove the "runtime" VP data in favor of direct programming of VP registers.
The VP is in the PRM, which is in the wakeup powerdomain, so there is no
need to keep the state dynamically.
Fixes to original version from Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Create new helper function in VP layer for updating VP error gain.
Currently used during pre-scale for VP force update and VC bypass.
TODO: determine if this can be removed from the pre-scale path and
moved to VP enable path.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add sys clock name and rate to struct voltage domain. SoC specific
voltagedomain init code initializes sys clock name. After clock
framework is initialized, voltage late init will then use use the
sys_clk rate to calculate the various timing that depend on that rate.
Signed-off-by: Kevin Hilman <khilman@ti.com>
In struct omap_vp_common, the shift value can be derived from the mask
value by using __ffs(), so remove the shift value for the various
VPCONFIG bitfields, and use __ffs() in the code for the shift value.
While here, rename field names in kerneldoc comment to match actual
field names in structure. Also, cleanup indendentaion for other VP
register accesses in omap_vp_init().
No functional changes.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove read-only debugfs interface to VP values. Most of the values
are init-time only and never change. Current voltage value should be
retreived from the (eventual) regulator framework interface to the
voltage domain.
Fixes to original version provided by Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
- move VP instance struct from vdd_info into struct voltage domain
- remove _data suffix from structure name
- rename vp_ prefix from vp_common field: accesses are now vp->common
- move vp_enabled bool from vdd_info into VP instance
- remove remaining references to omap_vdd_info
No functional changes.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Instead of reading current vsel value from the VP's voltage register,
just use current nominal voltage translated into vsel via the PMIC.
Doing this allows VC bypass scaling to work even without a VP configured.
Signed-off-by: Kevin Hilman <khilman@ti.com>
On OMAP3+, all VC channels have the the same bitfield ordering for all
VC channels, except the OMAP4 MPU channel. This appears to be a freak
accident as all other VC channel (including OMAP5) have the standard
configuration. Handle the mutant case by adding a per-channel flag
to signal the deformity and handle it during VC init.
Special thanks to Nishanth Menon <nm@ti.com> for finding this problem
and for proposing the initial solution.
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove hard-coded I2C configuration in favor of settings that can be
configured from PMIC-specific values. Currently only high-speed mode
and the master-code value are supported, since they were the only
fields currently used, but extending this is now trivial.
Thanks to Nishanth Menon <nm@ti.com> for reporting/fixing a sparse
problem and making omap_vc_i2c_init() static, as well as finding and
fixing a problem with the shift/mask of mcode.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Move structure containing PMIC configurable settings into struct
voltagedomain. In the process, rename from omap_volt_pmic_info to
omap_voltdm_pmic (_info suffix is not helpful.)
No functional changes.
Signed-off-by: Kevin Hilman <khilman@ti.com>
VC channel configuration is programmed based on settings coming from
the PMIC configuration.
Currently, the VC channel to PMIC mapping is a simple one-to-one
mapping. Whenever a VC channel parameter is configured (i2c slave
addres, PMIC register address, on/ret/off command), the corresponding
bits are enabled in the VC channel configuration register.
If necessary, the programmability of channel configuration settings
could be extended to board/PMIC files, however, because this patch
changes the channel configuration to be programmed based on existing
values from the PMIC settings, it may not be required.
Also note that starting with OMAP4, where there are more than 2
channels, one channel is identified as the "default" channel. When
any of the bits in the channel config for the other channels are zero,
it means to use the default channel. The OMAP4 TRM (at least through
NDA version Q) is wrong in describing which is the default channel.
The default channel on OMAP4 is MPU, not CORE as decribed in the TRM.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Configuring the on/onlp/ret/off command values is common to OMAP3 & 4.
Move from OMAP3-only init into common VC init.
Signed-off-by: Kevin Hilman <khilman@ti.com>
- add setup_time field to struct omap_vc_channel (init'd from PMIC data)
- use VC/VP register access helper for read/modify/write
- move VFSM structure from omap_vdd_info into struct voltagedomain
- remove redunant _data suffix from VFSM structures and variables
- remove voltsetup_shift, use ffs() on the mask value to find the shift
Signed-off-by: Kevin Hilman <khilman@ti.com>
The PMIC configurable variables should be isolated to VC initialization.
The rest of the VC functions (like VC bypass) should use the i2c slave address
and voltage register address fields from struct omap_vc_channel.
Signed-off-by: Kevin Hilman <khilman@ti.com>
- support both voltage register address and command register address
for each VC channel
- add fields for voltage register address (volra) and command register
address (cmdra) to struct omap_vc_channel
- use VC/VP register access read/modify/write helper
- remove volra_shift field (use __ffs(mask) for shift value)
- I2C addresses 10-bit, change size to u16
Signed-off-by: Kevin Hilman <khilman@ti.com>
- Add an i2c_slave_address field to the omap_vc_channel
- use VC/VP read/modify/write helper instead of open-coding
- remove smps_sa_shift, use __ffs(mask) for shift value
- I2C addresses 10-bit, change size to u16
Special thanks to Shweta Gulati <shweta.gulati@ti.com> for suggesting
the use of __ffs(x) instead of ffs(x) - 1.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Convert VC/VP register access to use PRM VC/VP accessor functions. In
the process, move the read/write function pointers from vdd_info into
struct voltagedomain.
No functional changes.
Additional cleanup:
- remove prm_mod field from VC/VP data structures, the PRM register
access functions know which PRM module to use.
Signed-off-by: Kevin Hilman <khilman@ti.com>
On OMAP3+, the voltage controller (VC) and voltage processor (VP) are
inside the PRM. Add some PRM helper functions for register access to
these module registers.
Thanks to Nishanth Menon for finding/fixing a sparse problem.
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Replace the VP tranxdone check/clear with helper functions from the
PRM layer.
In the process, remove prm_irqst_* voltage structure fields for IRQ
status checking which are no longer needed.
Since these reads/writes of the IRQ status bits were the only PRM
accesses that were not to VC/VP registers, this allows the rest of the
register accesses in the VC/VP code to use VC/VP specific register
access functions (done in the following patch.)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add SoC specific PRM VP helper functions for checking and clearing
the VP transaction done status.
Longer term, these events should be handled by the forthcoming PRCM
interrupt handler.
Signed-off-by: Kevin Hilman <khilman@ti.com>
The VC layer can support PMICs with separate voltage and command
registers by putting the different registers in the PRM_VC_SMPS_VOL_RA
and PRCM_VC_SMPS_CMD_RA registers respectively.
The PMIC data must supply at least a voltage register address
(volt_reg_addr). The command register address (cmd_reg_addr) is
optional. If the PMIC data does not supply a separate command
register address, the VC will use the voltage register address for both.
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch is primarily a move of VP specific code from voltage.c into
its own code in vp.c and adds prototypes to vp.h
No functional changes, except debugfs...
VP debugfs moved to 'vp' subdir of <debugfs>/voltage/ and 'vp_'
prefixes removed from all debugfs filenames.
Signed-off-by: Kevin Hilman <khilman@ti.com>
VC is initialized first, set default scaling method to VC bypass.
If/when VP is initialized, default scaling method will be changed to
VP force-update.
Enabling VC bypass as default as soon as VC is initialized allows for
VC bypass scaling to work when no VP is configured/initialized for a
given voltage domain.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Move the VC instance struct from omap_vdd_info into struct voltagedomain.
While moving, perform some misc. renames for readability.
No functional changes.
Summary of renames:
- rename omap_vc_instance to omap_vc_channel, since there is only
one instance of the VC IP and this actually represents channels
using TRM terminology.
- rename 'vc_common' field of VC channel which led to:
s/vc->vc_common/vc->common/
- remove redundant '_data' suffix
- OMAP3: vc1 --> vc_mpu, vc2 --> vc_core
- omap_vc_bypass_scale_voltage() -> omap_vc_bypass_scale()
Signed-off-by: Kevin Hilman <khilman@ti.com>
merge
As part of the voltage layer cleanup, split out VC specific code into
a dedicated VC layer. This patch primarily just moves VC code from
voltage.c into vc.c, and adds prototypes to vc.h.
No functional changes.
For readability, each function was given a local 'vc' pointer:
struct omap_vc_instance_data *vc = voltdm->vdd->vc_data;
and a global replace of s/vdd->vc_data/vc/ was done.
Also vc_init was renamed to vc_init_channel to reflect that this is
per-VC channel initializtion.
Signed-off-by: Kevin Hilman <khilman@ti.com>
When a powerdomain is registered and it has an associated voltage domain,
add the powerdomain to the voltagedomain using voltdm_add_pwrdm().
Also add voltagedomain iterator helper functions to iterate over all
registered voltagedomains and all powerdomains associated with a
voltagedomain.
Modeled after a similar relationship between clockdomains and powerdomains.
Signed-off-by: Kevin Hilman <khilman@ti.com>
When a powerdomain is registered, lookup the voltage domain by name
and keep a pointer to the containing voltagedomain in the powerdomain
structure.
Modeled after similar method between powerdomain and clockdomain layers.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add voltage domain name to indicate which voltagedomain each
powerdomain is in.
The fixed voltage domain like ldo_wakeup for emu and wkup power
domain is added too.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
[khilman@ti.com]: renamed wakeup domain: s/ldo_wakeup/wakeup/
Signed-off-by: Kevin Hilman <khilman@ti.com>
Create basic voltagedomains for OMAP2 and associate OMAP2 powerdomains
with the newly created voltage domains.
While here, update copyright on powerdomain data to 2011.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Each powerdomain is associated with a voltage domain. Add an entry to
struct powerdomain where the enclosing voltagedomain can be
referenced.
Modeled after similar relationship between clockdomains and powerdomains.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add a 'bool scalable' flag to the struct powerdomain and set it for
the scalable domains on OMAP3 and OMAP4.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add wakeup voltage domain so that the wakeup powerdomain can have an
associated powerdomain. Note that the scalable flat is not set for
the this voltagedomain, so it will not be fully initialized like
scalable voltage domains.
Signed-off-by: Kevin Hilman <khilman@ti.com>
This voltage domain (a.k.a. VDD1) contains both the MPU and the IVA, so
rename appropriately.
Also fixup any users of the "mpu" name to use "mpu_iva"
Signed-off-by: Kevin Hilman <khilman@ti.com>
Start cleaning up the voltage layer to have a voltage domain layer
that resembles the structure of the existing clock and power domain
layers. To that end:
- move the 'struct voltagedomain' out of 'struct omap_vdd_info' to
become the primary data structure.
- convert any functions taking a pointer to struct omap_vdd_info into
functions taking a struct voltagedomain pointer.
- convert the register & initialize of voltage domains to look like
that of powerdomains
- convert omap_voltage_domain_lookup() to voltdm_lookup(), modeled
after the current powerdomain and clockdomain lookup functions.
- omap_voltage_late_init(): only configure VDD info when
the vdd_info struct is non-NULL
Signed-off-by: Kevin Hilman <khilman@ti.com>
Eliminate need for global variables for the various PRM module offsets by
making them part of the VP/VC common structures
Eventually, these will likely be moved again, or more likely removed
when VP/VC code is isolated, but for now just getting rid of them as
global variabes so that the voltage domain initialization can be
cleaned up.
Signed-off-by: Kevin Hilman <khilman@ti.com>
The voltage domain pointer currently in struct omap_hwmod is not used
and does not belong here. Instead, voltage domains will be associated
with powerdomains in forthcoming patches.
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The numbers obtained from the hypervisor really can't ever lead to an
overflow here, only the original calculation going through the order
of the range could have. This avoids the (as Jeremy points outs)
somewhat ugly NULL-based calculation here.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The keypad controller requires a external pull-up for all the keypad
row lines. Fix the incorrect pad configuration for keypad controller
row lines by enabling the pad pull-up for the all row lines of the
keypad controller.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
clkdev framework uses global mutex to protect clock tree, so it is not
possible to call clk_get() in interrupt context. This patch fixes this
issue and makes system reset by watchdog call working again.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
According to commit 96d78686d4("ARM: S3C64XX: Add PWM backlight
support on SMDK6410") and commit f00207b255("ARM: SAMSUNG: Create
a common infrastructure for PWM backlight support"), this should
not be used anymore.
And this patch fixes follwing warning:
arch/arm/mach-s3c64xx/mach-smdk6410.c:296: warning: 'smdk6410_backlight_device' defined but not used
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
[kgene.kim@samsung.com: modified commit message]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
System resume can't be completed because mct-frc isn't restarted
after system suspends. This patch restarts mct-frc during system
resume.
Reported-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The commit 5dfc54e087
("ARM: GIC: avoid routing interrupts to offline CPUs")
prevents routing interrupts to offline CPUs. But in
case of timer on EXYNOS4, the irq_set_affinity() method
is called in percpu_timer_setup() before CPU1 becomes
online. So this patch fixes routing timer interrupt to
offline CPU.
Reported-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
According to commmit af90f10d ("ARM: 6759/1: smp: Select
local timers vs broadcast timer support"), the return type
of local_timer_setup() should be int instead of void.
Reported-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The PLL4650C is used for VPLL on EXYNOS4 so should be fixed.
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
[kgene.kim@samsung.com: added message]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since GPIOLIB is optional on alpha, GENERIC_GPIO must not be selected by
default. If GPIOLIB is enabled, it will select GENERIC_GPIO.
See <http://bugs.debian.org/638696> for an example of what 'def_bool y'
breaks.
Reported-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Cree <mcree@orcon.net.nz>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
richard@nod.at:
Fixes:
/usr/lib/gcc/x86_64-linux-gnu/4.4.5/../../../../lib/libc.a(strrchr.o): In function `rindex':
(.text+0x0): multiple definition of `strrchr'
If both STATIC_LINK and UML_NET_VDE are set to "y" libc's strrchr may
clash with the kernel implementation.
This workaround comes originally from Jeff Dike:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=494995#35
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1) take subarch-specific stuff to subarch_ptrace()
2) PTRACE_{PEEK,POKE}{TEXT,DATA} is handled by ptrace_request() just fine...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's 32bit-only, not 64bit-only... And while we are at it, it's
set_fpxregs(), not set_fpregs()...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
while not doing free_irq() from irq handler is commendable, kfree() on the
data passed to said handler before free_irq() is Not Good(tm). Freeing
the stack it's being run on is also not nice... Solution: delay actually
freeing stuff.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... so set winch->fd to -1 before doing free_irq(), to avoid having
winch_interrupt() come from/during the latter and attempt to do
reactivate_fd() on something that's already gone.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
