The DSI PLLs are handled by the generic clock framework
since ages, this code is completely unused and misleading.
Delete it.
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The display clocks are handled by the generic clock framework
since ages, this code is completely unused and misleading.
Delete it.
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is a distinct version of the Ux500 U8420 variant
with "sysclk", as can be seen from the vendor code that
didn't make it upstream, this firmware lacks the
ULPPLL (ultra-low power phase locked loop) which in
effect means that the timer clock is instead wired to
the 32768 Hz always-on clock.
This has some repercussions when enabling the timer
clock as the code as it stands will disable the timer
clock on these platforms (lacking the so-called
"doze mode") and obtaining the wrong rate of the timer
clock.
The timer frequency is of course needed very early in
the boot, and as a consequence, we need to shuffle
around the early PRCMU init code: whereas in the past
we did not need to look up the PRCMU firmware version
in the early init, but now we need to know the version
before the core system timers are registered so we
restructure the platform callbacks to the PRCMU so as
not to take any arguments and instead look up the
resources it needs directly from the device tree
when initializing.
As we do not yet support any platforms using this
firmware it is not a regression, but as PostmarketOS
is starting to support products with this firmware we
need to fix this up.
The low rate of 32kHz also makes the MTU timer unsuitable
as delay timer but this needs to be fixed in a separate
patch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Based on 1 normalized pattern(s):
license terms gnu general public license v2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 37 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.724130665@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are trying to decompose and decentralize the code in
the DB8500 PRCMU out into subdrivers. The code moved in
this patch concerns a group of functions used for
decoupling and recoupling the IRQs from the GIC. During
sleep and idle the Ux500 system will transfer all IRQ
handling to the PRCMU using these functions.
Basically we are left with the two alternatives of code
placement as:
- arch/arm/mach-ux500/pm.c - this because the code is
closely related to the GIC, and takes ownership of
some of the registers from the PRCMU related to this
PM functionality.
- drivers/mfd/db8500-prcmu-pm.c - because the code is
affecting stuff in the PRCMU register range. But then
this code needs to remap and handle GIC registers.
This patch implementation is taking the first approach.
Currently the cpuidle driver is the only piece of code
using this set of functions, but it will later also be
used by the suspend/resume code which is currently under
review.
The header file is moved to:
<linux/platform_data/arm-ux500-pm.h>
The function prototypes need to be placed in a globally
visible header since the CPUidle code is planned to move
out to drivers/cpuidle.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Rickard Andersson <rickard.andersson@stericsson.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch will make an early remapping of the PRCMU, to be
used when setting up the clocks, that will call down into parts
of the PRCMU driver before it is probed.
Going forward this will be removed like this:
- The mailbox subsystem need to be merged.
http://marc.info/?l=linux-kernel&m=136314559201983&w=2
- At this point the PRCMU clock code can be moved over to the
ux500 clock driver in drivers/clk/ux500/* and maintained
there in a decentralized manner.
- This early initcall and PRCMU base parameters become part of
the ux500_clk_init() call instead.
Cc: Suman Anna <s-anna@ti.com>
Cc: Loic Pallardy <loic.pallardy@st.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When trying to get rid of the cross-includes of <mach/id.h>
from different drivers, so we can localize ASIC/CPU detection
to the mach-ux500 folder, we run into the way the PRCMU
handles base addresses and firmware detection.
This patch updates the firmware version detection to pass
the required information as platform data instead of
relying on cpu_is_* macros.
Now the PRCMU base address, the secondary TCDM area, the
TCPM area and the IRQ are passed as resources instead of
being grabbed from <mach/*> files. Incidentally this also
removes part of the reliance on <mach/irqs.h>.
Further it updates the firmware version detection, since the
location of the firmware ID bytes in the designated memory
are is now passed from the platform data instead. There is
no reason not to include the nice split-off of a struct to
hold the firmware information and a separate function to
populate it.
The patch actually rids the need to use the external
db8500_prcmu_early_init call at all, but I'm keepin back
that removal as I don't want the patch to be too big.
Cc: arm@kernel.org
Cc: Michel Jaoen <michel.jaouen@stericsson.com>
Cc: Lee Jones <lee.jones@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Loic Pallardy <loic.pallardy@stericsson.com>
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These static inlines are duplicating the task now done by the
Nomadik pinctrl drivers, so delete them from the prcmu static
inlines, also delete the register definitions as these should
only be known by the pinctrl driver.
Cc: Loic Pallardy <loic.pallardy@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Michel Jaouen <michel.jaouen@st.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This function needs to be exported to let clients be able to
request the ape opp 100 voltage.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Force the Modem wakeup by asserting the CaWakeReq signal before the
hostaccess_req/ack ping-pong sequence. The Awake_req signal is de-asserted
asserted at the same time than the hostaccess_req. Return error on failure
case so that the client using this can take appropiate steps.
Signed-off-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch removes the obsolete hwacc implementation in the
DB8500 PRCMU driver.
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch allows to check if the other core is in WFI
mode. It is the last check the idle routine has to do before
entering into the retention state.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch allows to check if there are some pending irqs
on the prcmu.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In the case we go to the retention mode, we decoupled the gic
in order to have the A9 core to reach a stable WFI state.
But we want the prcmu to wake up the A9 when the gic has a pending
irq which is done by copying the gic settings to the to the prcmu.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch introduces a routine to check if there are some
irqs pending on the gic. Usually this check is not relevant because
it appears racy (an irq can arrive right after this check), but in
the ux500 it makes sense because the prcmu decouples the gic from
the A9 cores.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch allows to decouple and recouple the gic from the PRCMU.
This is needed to put the A9 core in retention mode with the cpuidle
driver.
It is based on top of the "DB8500 PRCMU update" patchset.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds an initial PRCMU register access API, which
for now should only be used for a very limited set of registers.
The idea about this API is that we split the PRCMU driver in
one part that deals with interaction with the PRCMU firmware
and one part that simply provide write accessors in the PRCMU
register range. The latter are just a collection of registers
exposed in the PRCMU register range for various purposes and
not related to the PRCMU firmware.
Currently we support some limited GPIO, SPI and UART settings
through this API.
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This updates the operating point handling code by:
- Supporting the DDR OPP retention state.
- Supporting another low operating point named
APE_50_PARTLY_25_OPP
- Adding an interface to figure out if the sleep state change
was properly achieved.
Signed-off-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This prefixes a number of accessor functions with db8500_* since
they are DB8500-specific and we need to move to this naming
scheme.
We also replace numerous instances of machine_is() with cpu_is()
which covers the right type of ASICs rather than entire machines
i.e. boards.
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch exports a function that can be used to tell which
version of the DB8500 PRCMU firmware is available, and revamps the
firmware detection code a bit.
Reviewed-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This removes the U8400 legacy from PRCMU and cpufreq drivers.
This platform has no current in-kernel users.
Signed-off-by: Daniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now that we have a shared API between the DB8500 and DB5500
PRCMU's, switch to using this neutral API instead. We delete the
parts of db8500-prcmu.h that is now PRCMU-neutral, and calls will
be diverted to respective driver. Common registers are in
dbx500-prcmu-regs.h and common accessors and defines in
<linux/mfd/dbx500-prcmu.h> This way we get a a lot more
abstraction and code reuse.
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This updates the DB8500 PRCMU driver to the latest version
available internally. Nominally we would update the dependent
CPUfreq driver at the same time but since that is being moved
around in this patch set we postpone that by simply deactivating
it for the time being.
This is a snapshot of the current PRCMU firmware API as it looks
right now. The PRCMU firmware is still subject to change. This
also updates the CPUfreq driver to a newer version that will
utilize the new API.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Martin Persson <martin.persson@stericsson.com>
Signed-off-by: Per Fransson <per.xx.fransson@stericsson.com>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Sebastien Rault <sebastien.rault@stericsson.com>
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have decided that this function arbiter fits better in the MFD
subsystem. Since we need to concatenate the split header files we move
it basically like this:
mv mach-ux500/prcmu-db8500.c drivers/mfd/db8500-prcmu.c
mv mach-ux500/include/mach/prcmu-defs.h include/linux/mfd/db8500-prcmu.h
mv mach-ux500/include/mach/prcmu-regs.h drivers/mfd/db8500-prcmu-regs.h
mach-ux500/include/mach/prcmu.h >> include/linux/mfd/db8500-prcmu.h
rm arch/arm/mach-ux500/include/mach/prcmu.h
Then we update different #include statements and Makefile orders etc
to make the PRCMU driver compile, link and boot in the new place
without really changing any code.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
