Using skb_reserve(skb, I40E_SKB_PAD + (xdp->data - xdp->data_hard_start))
is clearly wrong since I40E_SKB_PAD already points to the offset where
the original xdp->data was sitting since xdp->data_hard_start is defined
as xdp->data - i40e_rx_offset(rx_ring) where latter offsets to I40E_SKB_PAD
when build skb is used.
However, also before cc5b114dcf ("bpf, i40e: add meta data support")
this seems broken since bpf_xdp_adjust_head() helper could have been used
to alter headroom and enlarge / shrink the frame and with that the assumption
that the xdp->data remains unchanged does not hold and would push a bogus
packet to upper stack.
ixgbe got this right in 9247080816 ("ixgbe: add XDP support for pass and
drop actions"). In any case, fix it by removing the I40E_SKB_PAD from both
skb_reserve() and truesize calculation.
Fixes: cc5b114dcf ("bpf, i40e: add meta data support")
Fixes: 0c8493d90b ("i40e: add XDP support for pass and drop actions")
Reported-by: Keith Busch <keith.busch@linux.intel.com>
Reported-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Tested-by: Keith Busch <keith.busch@linux.intel.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Various netfilter fixlets from Pablo and the netfilter team.
2) Fix regression in IPVS caused by lack of PMTU exceptions on local
routes in ipv6, from Julian Anastasov.
3) Check pskb_trim_rcsum for failure in DSA, from Zhouyang Jia.
4) Don't crash on poll in TLS, from Daniel Borkmann.
5) Revert SO_REUSE{ADDR,PORT} change, it regresses various things
including Avahi mDNS. From Bart Van Assche.
6) Missing of_node_put in qcom/emac driver, from Yue Haibing.
7) We lack checking of the TCP checking in one special case during SYN
receive, from Frank van der Linden.
8) Fix module init error paths of mac80211 hwsim, from Johannes Berg.
9) Handle 802.1ad properly in stmmac driver, from Elad Nachman.
10) Must grab HW caps before doing quirk checks in stmmac driver, from
Jose Abreu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
net: stmmac: Run HWIF Quirks after getting HW caps
neighbour: skip NTF_EXT_LEARNED entries during forced gc
net: cxgb3: add error handling for sysfs_create_group
tls: fix waitall behavior in tls_sw_recvmsg
tls: fix use-after-free in tls_push_record
l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()
l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels
mlxsw: spectrum_switchdev: Fix port_vlan refcounting
mlxsw: spectrum_router: Align with new route replace logic
mlxsw: spectrum_router: Allow appending to dev-only routes
ipv6: Only emit append events for appended routes
stmmac: added support for 802.1ad vlan stripping
cfg80211: fix rcu in cfg80211_unregister_wdev
mac80211: Move up init of TXQs
mac80211_hwsim: fix module init error paths
cfg80211: initialize sinfo in cfg80211_get_station
nl80211: fix some kernel doc tag mistakes
hv_netvsc: Fix the variable sizes in ipsecv2 and rsc offload
rds: avoid unenecessary cong_update in loop transport
l2tp: clean up stale tunnel or session in pppol2tp_connect's error path
...
This patch addresses two issues. First it adds the correct bit definitions
for the SECTXSTAT and SECRXSTAT registers. Then it makes use of those
definitions to test for if IPsec has been disabled on the part and if so we
do not enable it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reported-by: Andre Tomt <andre@tomt.net>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes two issues. First we add an early test for the Tx and Rx
security block ready bits. By doing this we can avoid the need for waits or
loopback in the event that the security block is already flushed out.
Secondly we fix the boolean logic that was testing for the Tx OR Rx ready
bits being set and change it so that we only exit if the Tx AND Rx ready
bits are both set.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch moves the IPsec init function in ixgbe_sw_init. This way it is a
bit more consistent with the placement of similar initialization functions
and is placed before the reset_hw call which should allow us to clean up
any link issues that may be introduced by the fact that we force the link
up if somehow the device had IPsec still enabled before the driver was
loaded.
In addition to the function move it is necessary to change the assignment
of netdev->features. The easiest way to do this is to just test for the
existence of adapter->ipsec and if it is present we set the feature bits.
Fixes: 49a94d74d9 ("ixgbe: add ipsec engine start and stop routines")
Reported-by: Andre Tomt <andre@tomt.net>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no point in adding code if CONFIG_XFRM is defined that we won't
use unless CONFIG_XFRM_OFFLOAD is defined. So instead of leaving this code
floating around I am replacing the ifdef with what I believe is the correct
one so that we only include the code and variables if they will actually be
used.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we were enabling macvlan interfaces we weren't correctly configuring
things until ixgbe_setup_tc was called a second time either by tweaking the
number of queues or increasing the macvlan count past 15.
The issue came down to the fact that num_rx_pools is not populated until
after the queues and interrupts are reinitialized.
Instead of trying to set it sooner we can just move the call to setup at
least 1 traffic class to the SR-IOV/VMDq setup function so that we just set
it for this one case. We already had a spot that was configuring the queues
for TC 0 in the code here anyway so it makes sense to also set the number
of TCs here as well.
Fixes: 49cfbeb7a9 ("ixgbe: Fix handling of macvlan Tx offload")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-----BEGIN PGP SIGNATURE-----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=aFAi
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- unify AER decoding for native and ACPI CPER sources (Alexandru
Gagniuc)
- add TLP header info to AER tracepoint (Thomas Tai)
- add generic pcie_wait_for_link() interface (Oza Pawandeep)
- handle AER ERR_FATAL by removing and re-enumerating devices, as
Downstream Port Containment does (Oza Pawandeep)
- factor out common code between AER and DPC recovery (Oza Pawandeep)
- stop triggering DPC for ERR_NONFATAL errors (Oza Pawandeep)
- share ERR_FATAL recovery path between AER and DPC (Oza Pawandeep)
- disable ASPM L1.2 substate if we don't have LTR (Bjorn Helgaas)
- respect platform ownership of LTR (Bjorn Helgaas)
- clear interrupt status in top half to avoid interrupt storm (Oza
Pawandeep)
- neaten pci=earlydump output (Andy Shevchenko)
- avoid errors when extended config space inaccessible (Gilles Buloz)
- prevent sysfs disable of device while driver attached (Christoph
Hellwig)
- use core interface to report PCIe link properties in bnx2x, bnxt_en,
cxgb4, ixgbe (Bjorn Helgaas)
- remove unused pcie_get_minimum_link() (Bjorn Helgaas)
- fix use-before-set error in ibmphp (Dan Carpenter)
- fix pciehp timeouts caused by Command Completed errata (Bjorn
Helgaas)
- fix refcounting in pnv_php hotplug (Julia Lawall)
- clear pciehp Presence Detect and Data Link Layer Status Changed on
resume so we don't miss hotplug events (Mika Westerberg)
- only request pciehp control if we support it, so platform can use
ACPI hotplug otherwise (Mika Westerberg)
- convert SHPC to be builtin only (Mika Westerberg)
- request SHPC control via _OSC if we support it (Mika Westerberg)
- simplify SHPC handoff from firmware (Mika Westerberg)
- fix an SHPC quirk that mistakenly included *all* AMD bridges as well
as devices from any vendor with device ID 0x7458 (Bjorn Helgaas)
- assign a bus number even to non-native hotplug bridges to leave
space for acpiphp additions, to fix a common Thunderbolt xHCI
hot-add failure (Mika Westerberg)
- keep acpiphp from scanning native hotplug bridges, to fix common
Thunderbolt hot-add failures (Mika Westerberg)
- improve "partially hidden behind bridge" messages from core (Mika
Westerberg)
- add macros for PCIe Link Control 2 register (Frederick Lawler)
- replace IB/hfi1 custom macros with PCI core versions (Frederick
Lawler)
- remove dead microblaze and xtensa code (Bjorn Helgaas)
- use dev_printk() when possible in xtensa and mips (Bjorn Helgaas)
- remove unused pcie_port_acpi_setup() and portdrv_acpi.c (Bjorn
Helgaas)
- add managed interface to get PCI host bridge resources from OF (Jan
Kiszka)
- add support for unbinding generic PCI host controller (Jan Kiszka)
- fix memory leaks when unbinding generic PCI host controller (Jan
Kiszka)
- request legacy VGA framebuffer only for VGA devices to avoid false
device conflicts (Bjorn Helgaas)
- turn on PCI_COMMAND_IO & PCI_COMMAND_MEMORY in pci_enable_device()
like everybody else, not in pcibios_fixup_bus() (Bjorn Helgaas)
- add generic enable function for simple SR-IOV hardware (Alexander
Duyck)
- use generic SR-IOV enable for ena, nvme (Alexander Duyck)
- add ACS quirk for Intel 7th & 8th Gen mobile (Alex Williamson)
- add ACS quirk for Intel 300 series (Mika Westerberg)
- enable register clock for Armada 7K/8K (Gregory CLEMENT)
- reduce Keystone "link already up" log level (Fabio Estevam)
- move private DT functions to drivers/pci/ (Rob Herring)
- factor out dwc CONFIG_PCI Kconfig dependencies (Rob Herring)
- add DesignWare support to the endpoint test driver (Gustavo
Pimentel)
- add DesignWare support for endpoint mode (Gustavo Pimentel)
- use devm_ioremap_resource() instead of devm_ioremap() in dra7xx and
artpec6 (Gustavo Pimentel)
- fix Qualcomm bitwise NOT issue (Dan Carpenter)
- add Qualcomm runtime PM support (Srinivas Kandagatla)
- fix DesignWare enumeration below bridges (Koen Vandeputte)
- use usleep() instead of mdelay() in endpoint test (Jia-Ju Bai)
- add configfs entries for pci_epf_driver device IDs (Kishon Vijay
Abraham I)
- clean up pci_endpoint_test driver (Gustavo Pimentel)
- update Layerscape maintainer email addresses (Minghuan Lian)
- add COMPILE_TEST to improve build test coverage (Rob Herring)
- fix Hyper-V bus registration failure caused by domain/serial number
confusion (Sridhar Pitchai)
- improve Hyper-V refcounting and coding style (Stephen Hemminger)
- avoid potential Hyper-V hang waiting for a response that will never
come (Dexuan Cui)
- implement Mediatek chained IRQ handling (Honghui Zhang)
- fix vendor ID & class type for Mediatek MT7622 (Honghui Zhang)
- add Mobiveil PCIe host controller driver (Subrahmanya Lingappa)
- add Mobiveil MSI support (Subrahmanya Lingappa)
- clean up clocks, MSI, IRQ mappings in R-Car probe failure paths
(Marek Vasut)
- poll more frequently (5us vs 5ms) while waiting for R-Car data link
active (Marek Vasut)
- use generic OF parsing interface in R-Car (Vladimir Zapolskiy)
- add R-Car V3H (R8A77980) "compatible" string (Sergei Shtylyov)
- add R-Car gen3 PHY support (Sergei Shtylyov)
- improve R-Car PHYRDY polling (Sergei Shtylyov)
- clean up R-Car macros (Marek Vasut)
- use runtime PM for R-Car controller clock (Dien Pham)
- update arm64 defconfig for Rockchip (Shawn Lin)
- refactor Rockchip code to facilitate both root port and endpoint
mode (Shawn Lin)
- add Rockchip endpoint mode driver (Shawn Lin)
- support VMD "membar shadow" feature (Jon Derrick)
- support VMD bus number offsets (Jon Derrick)
- add VMD "no AER source ID" quirk for more device IDs (Jon Derrick)
- remove unnecessary host controller CONFIG_PCIEPORTBUS Kconfig
selections (Bjorn Helgaas)
- clean up quirks.c organization and whitespace (Bjorn Helgaas)
* tag 'pci-v4.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (144 commits)
PCI/AER: Replace struct pcie_device with pci_dev
PCI/AER: Remove unused parameters
PCI: qcom: Include gpio/consumer.h
PCI: Improve "partially hidden behind bridge" log message
PCI: Improve pci_scan_bridge() and pci_scan_bridge_extend() doc
PCI: Move resource distribution for single bridge outside loop
PCI: Account for all bridges on bus when distributing bus numbers
ACPI / hotplug / PCI: Drop unnecessary parentheses
ACPI / hotplug / PCI: Mark stale PCI devices disconnected
ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug
PCI: hotplug: Add hotplug_is_native()
PCI: shpchp: Add shpchp_is_native()
PCI: shpchp: Fix AMD POGO identification
PCI: mobiveil: Add MSI support
PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver
PCI/AER: Decode Error Source Requester ID
PCI/AER: Remove aer_recover_work_func() forward declaration
PCI/DPC: Use the generic pcie_do_fatal_recovery() path
PCI/AER: Pass service type to pcie_do_fatal_recovery()
PCI/DPC: Disable ERR_NONFATAL handling by DPC
...
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-06-05
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add a new BPF hook for sendmsg similar to existing hooks for bind and
connect: "This allows to override source IP (including the case when it's
set via cmsg(3)) and destination IP:port for unconnected UDP (slow path).
TCP and connected UDP (fast path) are not affected. This makes UDP support
complete, that is, connected UDP is handled by connect hooks, unconnected
by sendmsg ones.", from Andrey.
2) Rework of the AF_XDP API to allow extending it in future for type writer
model if necessary. In this mode a memory window is passed to hardware
and multiple frames might be filled into that window instead of just one
that is the case in the current fixed frame-size model. With the new
changes made this can be supported without having to add a new descriptor
format. Also, core bits for the zero-copy support for AF_XDP have been
merged as agreed upon, where i40e bits will be routed via Jeff later on.
Various improvements to documentation and sample programs included as
well, all from Björn and Magnus.
3) Given BPF's flexibility, a new program type has been added to implement
infrared decoders. Quote: "The kernel IR decoders support the most
widely used IR protocols, but there are many protocols which are not
supported. [...] There is a 'long tail' of unsupported IR protocols,
for which lircd is need to decode the IR. IR encoding is done in such
a way that some simple circuit can decode it; therefore, BPF is ideal.
[...] user-space can define a decoder in BPF, attach it to the rc
device through the lirc chardev.", from Sean.
4) Several improvements and fixes to BPF core, among others, dumping map
and prog IDs into fdinfo which is a straight forward way to correlate
BPF objects used by applications, removing an indirect call and therefore
retpoline in all map lookup/update/delete calls by invoking the callback
directly for 64 bit archs, adding a new bpf_skb_cgroup_id() BPF helper
for tc BPF programs to have an efficient way of looking up cgroup v2 id
for policy or other use cases. Fixes to make sure we zero tunnel/xfrm
state that hasn't been filled, to allow context access wrt pt_regs in
32 bit archs for tracing, and last but not least various test cases
for fixes that landed in bpf earlier, from Daniel.
5) Get rid of the ndo_xdp_flush API and extend the ndo_xdp_xmit with
a XDP_XMIT_FLUSH flag instead which allows to avoid one indirect
call as flushing is now merged directly into ndo_xdp_xmit(), from Jesper.
6) Add a new bpf_get_current_cgroup_id() helper that can be used in
tracing to retrieve the cgroup id from the current process in order
to allow for e.g. aggregation of container-level events, from Yonghong.
7) Two follow-up fixes for BTF to reject invalid input values and
related to that also two test cases for BPF kselftests, from Martin.
8) Various API improvements to the bpf_fib_lookup() helper, that is,
dropping MPLS bits which are not fully hashed out yet, rejecting
invalid helper flags, returning error for unsupported address
families as well as renaming flowlabel to flowinfo, from David.
9) Various fixes and improvements to sockmap BPF kselftests in particular
in proper error detection and data verification, from Prashant.
10) Two arm32 BPF JIT improvements. One is to fix imm range check with
regards to whether immediate fits into 24 bits, and a naming cleanup
to get functions related to rsh handling consistent to those handling
lsh, from Wang.
11) Two compile warning fixes in BPF, one for BTF and a false positive
to silent gcc in stack_map_get_build_id_offset(), from Arnd.
12) Add missing seg6.h header into tools include infrastructure in order
to fix compilation of BPF kselftests, from Mathieu.
13) Several formatting cleanups in the BPF UAPI helper description that
also fix an error during rst2man compilation, from Quentin.
14) Hide an unused variable in sk_msg_convert_ctx_access() when IPv6 is
not built into the kernel, from Yue.
15) Remove a useless double assignment in dev_map_enqueue(), from Colin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the ndo_xdp_flush call implementation ixgbe_xdp_flush
as no callers of ndo_xdp_flush are left.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Remove the ndo_xdp_flush call implementation i40e_xdp_flush
as no callers of ndo_xdp_flush are left.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Fix up a cast problem introduced by a sparse cleanup patch. This fixes
a problem where the encrypted packets were not recognized on Rx and
subsequently dropped.
Fixes: 9cfbfa701b ("ixgbe: cleanup sparse warnings")
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure we don't try to offload the decryption of an incoming
packet that should get delivered to the management engine. This
is a corner case that will likely be very seldom seen, but could
really confuse someone if they were to hit it.
Suggested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Similar to ixgbevf, the same possibility for race exists. Extend the RTNL
lock in ixgbe_reset_subtask() to protect the state bits; this is to make
sure that we get the most up-to-date values for the bits and avoid a
possible race when going down.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for XDP meta data when using build skb variant of
the i40e driver. Implementation is analogous to the existing
ixgbe and ixgbevf support for meta data from 366a88fe2f ("bpf,
ixgbe: add meta data support") and be8333322e ("ixgbevf: Add
support for meta data"). With the build skb variant we get
192 bytes of extra headroom which can be used for encaps or
meta data.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Tested-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe_dbg_reg_ops_read and ixgbe_dbg_netdev_ops_read copy-pasting
the same code except for ixgbe_dbg_netdev_ops_buf/ixgbe_dbg_reg_ops_buf,
so introduce a helper ixgbe_dbg_common_ops_read to remove redundant code.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Extend the RTNL lock in ixgbevf_reset_subtask() to protect the state bits
check in addition to the call to ixgbevf_reinit_locked().
This is to make sure that we get the most up-to-date values for the bits
and avoid a possible race when going down.
Suggested-by: Zhiping du <zhipingdu@tencent.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the case of the VF driver it is supposed to provide a context descriptor
that allows us to provide information about the header offsets inside of
the frame. However in the case of XDP we don't really have any of that
information since the data is minimally processed. As a result we were
seeing malicious driver detection (MDD) events being triggered when the PF
had that functionality enabled.
To address this I have added a bit of new code that will "prime" the XDP
ring by providing one context descriptor that assumes the minimal setup of
an Ethernet frame which is an L2 header length of 14. With just that we can
provide enough information to make the hardware happy so that we don't
trigger MDD events.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move 10ms sleep out of function resetting TX queue.
Reset all the TX queues in one turn and
wait for all of them just once.
Use usleep_range() instead of mdelay() in order not to
affect transmission on other interfaces.
Signed-off-by: Sergey Nemov <sergey.nemov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Issuing "ip link set up/down" can block TSICR interrupts, what results in
missing PTP Tx timestamp and no PPS pulse generation.
Problem happens when the link is set up with the TSICR interrupts pending.
ICR is cleared before enabling interrupts, while TSICR is not. When all TSICR
interrupts are pending at this moment, time_sync interrupt will never
be generated. TSICR should be cleared as well.
In order to reproduce the issue:
1. Setup linux with IEEE 1588 grandmaster and PPS output enabled
2. Continue setting link up/down with random intervals between commands
3. Wait until PPS is not generated ( only one pulse is generated and PPS
dies), and ptp4l complains constantly about Tx timeout.
Signed-off-by: Joanna Yurdal <jyu@trackman.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There have been multiple reports of crashes that look like
kernel: RIP: 0010:[<ffffffff8110303f>] timecounter_read+0xf/0x50
[...]
kernel: Call Trace:
kernel: [<ffffffffa0806b0f>] e1000e_phc_gettime+0x2f/0x60 [e1000e]
kernel: [<ffffffffa0806c5d>] e1000e_systim_overflow_work+0x1d/0x80 [e1000e]
kernel: [<ffffffff810992c5>] process_one_work+0x155/0x440
kernel: [<ffffffff81099e16>] worker_thread+0x116/0x4b0
kernel: [<ffffffff8109f422>] kthread+0xd2/0xf0
kernel: [<ffffffff8163184f>] ret_from_fork+0x3f/0x70
These can be traced back to the fact that e1000e_systim_reset() skips the
timecounter_init() call if e1000e_get_base_timinca() returns -EINVAL, which
leads to a null deref in timecounter_read().
Commit 83129b37ef ("e1000e: fix systim issues", v4.2-rc1) reworked
e1000e_get_base_timinca() in such a way that it can return -EINVAL for
e1000_pch_spt if the SYSCFI bit is not set in TSYNCRXCTL.
Some experimentation has shown that on I219 (e1000_pch_spt, "MAC: 12")
adapters, the E1000_TSYNCRXCTL_SYSCFI flag is unstable; TSYNCRXCTL reads
sometimes don't have the SYSCFI bit set. Retrying the read shortly after
finds the bit to be set. This was observed at boot (probe) but also link up
and link down.
Moreover, the phc (PTP Hardware Clock) seems to operate normally even after
reads where SYSCFI=0. Therefore, remove this register read and
unconditionally set the clock parameters.
Reported-by: Achim Mildenberger <admin@fph.physik.uni-karlsruhe.de>
Message-Id: <20180425065243.g5mqewg5irkwgwgv@f2>
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1075876
Fixes: 83129b37ef ("e1000e: fix systim issues")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When passed the XDP_XMIT_FLUSH flag ixgbe_xdp_xmit now performs the
same kind of ring tail update as in ixgbe_xdp_flush. The update tail
code in ixgbe_xdp_flush is generalized and shared with ixgbe_xdp_xmit.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When passed the XDP_XMIT_FLUSH flag i40e_xdp_xmit now performs the
same kind of ring tail update as in i40e_xdp_flush. The advantage is
that all the necessary checks have been performed and xdp_ring can be
updated, instead of having to perform the exact same steps/checks in
i40e_xdp_flush
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch only change the API and reject any use of flags. This is an
intermediate step that allows us to implement the flush flag operation
later, for each individual driver in a separate patch.
The plan is to implement flush operation via XDP_XMIT_FLUSH flag
and then remove XDP_XMIT_FLAGS_NONE when done.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Filling in the padding slot in the bpf structure as a bug fix in 'ne'
overlapped with actually using that padding area for something in
'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous code was optimistic, accepting the offload of whole action
chain when there was a single known action (drop/redirect). This results
in offloading a rule which should not be offloaded, because its behavior
cannot be reproduced in the hardware.
For example:
$ tc filter add dev eno1 parent ffff: protocol ip \
u32 ht 800: order 1 match tcp src 42 FFFF \
action mirred egress mirror dev enp1s16 pipe \
drop
The controller is unable to mirror the packet to a VF, but still
offloads the rule by dropping the packet.
Change the approach of the function to a pessimistic one, rejecting the
chain when an unknown action is found. This is better suited for future
extensions.
Note that both recognized actions always return TC_ACT_SHOT, therefore
it is safe to ignore actions behind them.
Signed-off-by: Ondřej Hlavatý <ohlavaty@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the driver used pcie_get_minimum_link() to warn when the NIC
is in a slot that can't supply as much bandwidth as the NIC could use.
pcie_get_minimum_link() can be misleading because it finds the slowest link
and the narrowest link (which may be different links) without considering
the total bandwidth of each link. For a path with a 16 GT/s x1 link and a
2.5 GT/s x16 link, it returns 2.5 GT/s x1, which corresponds to 250 MB/s of
bandwidth, not the true available bandwidth of about 1969 MB/s for a
16 GT/s x1 link.
Use pcie_print_link_status() to report PCIe link speed and possible
limitations instead of implementing this in the driver itself. This finds
the slowest link in the path to the device by computing the total bandwidth
of each link and compares that with the capabilities of the device.
The dmesg change is:
- PCI Express bandwidth of %dGT/s available
- (Speed:%s, Width: x%d, Encoding Loss:%s)
+ %u.%03u Gb/s available PCIe bandwidth (%s x%d link)
or, if the device is capable of better performance than is available in the
current slot:
- This is not sufficient for optimal performance of this card.
- For optimal performance, at least %dGT/s of bandwidth is required.
- A slot with more lanes and/or higher speed is suggested.
+ %u.%03u Gb/s available PCIe bandwidth, limited by %s x%d link at %s (capable of %u.%03u Gb/s with %s x%d link)
Note that the driver previously used dev_warn() to suggest using a
different slot, but pcie_print_link_status() uses dev_info() because if the
platform has no faster slot available, the user can't do anything about the
warning and may not want to be bothered with it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2018-05-24
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Björn Töpel cleans up AF_XDP (removes rebind, explicit cache alignment from uapi, etc).
2) David Ahern adds mtu checks to bpf_ipv{4,6}_fib_lookup() helpers.
3) Jesper Dangaard Brouer adds bulking support to ndo_xdp_xmit.
4) Jiong Wang adds support for indirect and arithmetic shifts to NFP
5) Martin KaFai Lau cleans up BTF uapi and makes the btf_header extensible.
6) Mathieu Xhonneux adds an End.BPF action to seg6local with BPF helpers allowing
to edit/grow/shrink a SRH and apply on a packet generic SRv6 actions.
7) Sandipan Das adds support for bpf2bpf function calls in ppc64 JIT.
8) Yonghong Song adds BPF_TASK_FD_QUERY command for introspection of tracing events.
9) other misc fixes from Gustavo A. R. Silva, Sirio Balmelli, John Fastabend, and Magnus Karlsson
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch change the API for ndo_xdp_xmit to support bulking
xdp_frames.
When kernel is compiled with CONFIG_RETPOLINE, XDP sees a huge slowdown.
Most of the slowdown is caused by DMA API indirect function calls, but
also the net_device->ndo_xdp_xmit() call.
Benchmarked patch with CONFIG_RETPOLINE, using xdp_redirect_map with
single flow/core test (CPU E5-1650 v4 @ 3.60GHz), showed
performance improved:
for driver ixgbe: 6,042,682 pps -> 6,853,768 pps = +811,086 pps
for driver i40e : 6,187,169 pps -> 6,724,519 pps = +537,350 pps
With frames avail as a bulk inside the driver ndo_xdp_xmit call,
further optimizations are possible, like bulk DMA-mapping for TX.
Testing without CONFIG_RETPOLINE show the same performance for
physical NIC drivers.
The virtual NIC driver tun sees a huge performance boost, as it can
avoid doing per frame producer locking, but instead amortize the
locking cost over the bulk.
V2: Fix compile errors reported by kbuild test robot <lkp@intel.com>
V4: Isolated ndo, driver changes and callers.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Since we no longer use i as an array index for the data variable,
replace the use of 'j' with 'i' so that we match the general loop
variable name.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add documentation for the i40e_get_stats_count, i40e_get_stat_strings
and i40e_get_ethtool_stats explaining that the number and ordering of
statistics must remain constant for a given netdevice.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A future patch is going to add a helper function i40e_add_ethtool_stats
that will help lower the amount of boiler plate code in the
i40e_get_ethtool_stats function.
This conversion will take place over many patches, and the helper
function will work by directly updating a reference to the data pointer.
Since this would not work combined with the current method of accessing
data like an array, update all the code that copies stats into the data
buffer to use direct updates to the pointer instead of array accesses.
This will prevent incorrect stat updates for patches in between the
conversion.
Similarly, when copying strings, we used a separate char *p pointer.
Instead, use the data pointer directly as it's already a (u8 *) type
which is the same size.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We always prefix these stats with a fixed string, so just fold this
prefix into the stat string definition. This preparatory work will make
it easier to implement a helper function to copy stats and strings into
the supplied buffers in a future patch.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't really want to use BUG_ON here since that would completely
crash the kernel, thus the reason we commented it out. We *can't* use
BUILD_BUG_ON because at least now (a) the sizes aren't constant (we are
fixing this) and (b) not all compilers are smart enough to understand
that "p - data" is a constant.
Instead, just use a WARN_ONCE so that the first time we end up with an
incorrect size we will dump a stack trace and a message, hopefully
highlighting the issues early in testing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Split the statistic strings and private flags strings into their own
separate functions to aid code readability.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool API for obtaining device statistics is not intended to allow
runtime changes in the number of statistics reported. It may *appear*
this way, as there is an ability to request the number of stats using
ethtool_get_set_count(). However, it is expected that this must always
return the same value for invocations of the same device.
If we don't satisfy this contract, and allow the number of stats to
change during run time, we could cause invalid memory accesses or report
the stat strings incorrectly. This is because the API for obtaining
stats is to (1) get the size, (2) get the strings and finally (3) get
the stats. Since these are each separate ethtool op commands, it is not
possible to maintain consistency by holding the RTNL lock over the whole
operation. This results in the potential for a race condition to occur
where the size changed between any of the 3 calls.
Avoid this issue by requiring that we always return the same value for
a given device. We can check any values which remain constant for the
life of the device, but must not report different sizes depending on
runtime attributes.
This patch specifically fixes the queue statistics to always return
every queue even if it's not currently in use.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool API for obtaining device statistics is not intended to allow
runtime changes in the number of statistics reported. It may *appear*
this way, as there is an ability to request the number of stats using
ethtool_get_set_count(). However, it is expected that this must always
return the same value for invocations of the same device.
If we don't satisfy this contract, and allow the number of stats to
change during run time, we could cause invalid memory accesses or report
the stat strings incorrectly. This is because the API for obtaining
stats is to (1) get the size, (2) get the strings and finally (3) get
the stats. Since these are each separate ethtool op commands, it is not
possible to maintain consistency by holding the RTNL lock over the whole
operation. This results in the potential for a race condition to occur
where the size changed between any of the 3 calls.
Avoid this issue by requiring that we always return the same value for
a given device. We can check any values which remain constant for the
life of the device, but must not report different sizes depending on
runtime attributes.
This patch specifically fixes the VEB statistics strings to always be
reported. Other issues will be fixed in future patches.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the same logic to free the skb after clearing the Tx timestamp bit
lock in i40e_ptp_stop as we use in the other locations. It is not as
important here since we are not racing against a future Tx timestamp
request (as we are disabling PTP at this point). However it is good to
be consistent in how we approach the bit lock so that future callers
don't copy the old anti-pattern.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This reverts commit 6710f970d9.
Gotta love when developers have offline discussions, thinking everyone
is reading their responses/dialog.
The change had the potential for a number of race conditions on
shutdown, which is why we are reverting the change.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the NVM read/erase/update AQ commands to align with
the latest specification.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set hw->mac.perm_addr in ixgbevf_set_mac() in order to avoid losing the
custom MAC on reset. This can happen in the following case:
>ip link set $vf address $mac
>ethtool -r $vf
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Do not validate the MAC address during a reset, unless the MAC was set on
the host. This way the VF will get a new MAC address every time it reloads.
Remove the "no MAC address assigned" message since it will get spammed on
reset and it doesn't help much as the MAC on the VF is randomly generated.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, during device_shutdown() ixgbe holds rtnl_lock for the duration
of lengthy ixgbe_close_suspend(). On machines with multiple ixgbe cards
this lock prevents scaling if device_shutdown() function is multi-threaded.
It is not necessary to hold this lock during ixgbe_close_suspend()
as it is not held when ixgbe_close() is called also during shutdown but for
kexec case.
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit f7f37e7ff2 ("ixgbe: handle close/suspend race with
netif_device_detach/present") ixgbe_close_suspend is called, from
ixgbe_close, only if the device is present, i.e. if it isn't detached.
That exposed a situation where IRQs weren't freed if a PCI error
recovery system opts to remove the device. For such case the pci channel
state is set to pci_channel_io_perm_failure and ixgbe_io_error_detected
was returning PCI_ERS_RESULT_DISCONNECT before calling
ixgbe_close_suspend consequentially not freeing IRQ and crashing when
the remove handler calls pci_disable_device, hitting a BUG_ON at
free_msi_irqs, which asserts that there is no non-free IRQ associated
with the device to be removed:
BUG_ON(irq_has_action(entry->irq + i));
The issue is fixed by calling the ixgbe_close_suspend before evaluate
the pci channel state.
Reported-by: Naresh Bannoth <nbannoth@in.ibm.com>
Reported-by: Abdul Haleem <abdhalee@in.ibm.com>
Signed-off-by: Mauro S M Rodrigues <maurosr@linux.vnet.ibm.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sparse complains valid conversions between restricted types, force
attribute is used to avoid those warnings.
Signed-off-by: Cathy Zhou <cathy.zhou@oracle.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a hardware reset support in VF driver.
It is needed because when a hardware reset is detected
adapter->state is in __I40EVF_RESETTING state before
i40evf_reset_task is called. Without this patch
unloading VF driver after a hardware reset ends
with a system crash.
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit bbc4e7d273 ("i40e: fix race condition with PTP_TX_IN_PROGRESS
bits") we modified the code which handles Tx timestamps so that we would
clear the progress bit as soon as possible.
A later commit 0bc0706b46 ("i40e: check for Tx timestamp timeouts during
watchdog") introduced similar code for detecting and handling cleanup of
a blocked Tx timestamp. This code did not use the same pattern for cleaning
up the skb.
Update this code to wait to free the skb until after the bit lock is
free, by first setting the ptp_tx_skb to NULL and clearing the lock.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
