The two variables are never used outside of their compilation unit, make
them static.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The HPD signal can be used for detecting HDMI cable plug and unplug event
without the need for polling the status of the line.
This will speed up detecting such event because we do not need to wait for
the next poll event to notice the state change.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Change dispc driver to use the DRM_MODE_REFLECT flags instead of a mirror
boolean.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
At the moment the dispc driver uses a custom enum for rotation. Change
it to use the DRM's DRM_MODE_ROTATE_*.
Note that mirroring is at the moment handled as a separate boolean in
the dispc driver, so we only use the DRM_MODE_ROTATE_* values.
Note, DSS HW uses clockwise rotation, DRM counter-clockwise.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Now that we use fourccs, we can also rename the 'color_mode' variables
to 'fourcc'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
This patch changes omapdrm to use DRM_FORMAT_* values instead of
OMAP_DSS_COLOR_* enum.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
In this step we drop 'enum omap_color_mode', and use u32 instead.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
enum omap_color_mode is a bitmask, so at the moment we present the
supported color modes as mask. To be able to move to fourccs, we need to
use an array to present the supported color modes.
As a first step towards fourccs, this patch changes the code to use an
array to store the enums.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omapdss.h contains prototypes for three functions, which are also
defined in dss_features.h. Remove the extra prototypes from omapdss.h.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We have three rotation methods supported by the SoCs with DSS: DMA,
VRFB and TILER.
DMA rotation works in theory on all DSS platforms, but in practice it's
unusable due to the huge amount of memory bandwidth it uses, and has
never really been used.
VRFB is available on OMAP3, but is not supported by omapdrm, even though
we have some code for it in the dispc driver.
TILER is supported on OMAP4/OMAP5/DRA7/AM5 platforms, but has some
driver bugs.
To clean up the driver to help fixing the TILER issues, this patch drops
the DMA and VRFB rotation support, leaving only TILER rotation.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
DSS IP versions 2 and 3 support CLUT modes (color lookup table), but the
driver has never supported those. We still have had some code for CLUT
modes. As the newer DSS IP versions have dropped CLUT support, we might
as well clean up the driver by removing the CLUT related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The omap_dss_find_output() function is unused, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Structs omap_overlay and omap_overlay_manager are not used, remove them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
get_resolution is not used, remove it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
get_dimensions function pointer is not used, remove it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The RFBI driver has not worked nor compiled for many years. There are
very few boards out there that use RFBI, and no one has stepped up to
fix it.
So let's remove the RFBI code that doesn't even compile.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
recommended_bpp hasn't been used for ages, remove the code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Non-DT booting is no longer supported, so remove legacy code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Non-DT booting is no longer supported, so remove legacy code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We only use read_irqenable() to flush posted write. Instead of having a
separate function for this, do the flush implicitly in write_irqenable().
Thus we can remove read_irqenable().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
At the moment we have ovl_set_channel_out() to configure the output
channel of an overlay. It makes sense to have this configuration as part
of the rest of overlay configuration, and in DSS6+ we need the output
channel when doing the other overlay configuration.
This patch adds a 'channel' parameter to ovl_setup(), so that all
overlay configuration is done via the same function, and removes the
ovl_set_channel_out().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
ovl_enabled() is not used anywhere, so remove it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The default display name is both unused and never set by platform data.
Remove default display name module parameter, platform data field and
runtime infrastructure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The OMAP driver has its own OF graph helpers that are similar to the
common helpers. This commit replaces most of the calls with the common
helpers. There's still a couple of custom helpers left, but the driver
needs more extensive changes to get rid of them.
In dss_init_ports, we invert the loop, looping through the known ports
and matching them to DT nodes rather than looping thru DT nodes and
matching them to the ports.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
The enum omap_plane conflicted with the same struct name for omapdrm
plane private data. This rename should solve the conflict.
The rename was implement with this very simple coccinelle patch:
------------------------
@@
@@
enum
-omap_plane
+omap_plane_id
------------------------
The patch was applied like this:
spatch --sp-file <cocci_file> --all-includes --in-place --dir drivers/gpu/drm/omapdrm
The above patch did not rename the actual enum definition. That was
added manually on top of the spatch changes.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When omapdss is loaded (all core components are in place) create a list of
devices used in the display graph. This list later can be used by omapdrm
via the omapdss_stack_is_ready() function to check that these components
are loaded. Based on this information, omapdrm can defer probe in case when
the omapdss stack is not ready yet.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The functions can be used to check a component (by it's of_node) if it is
part of the omapdss display or output list. If the component is found, it
means that the driver is loaded.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSS uses "replication logic" to convert color components from smaller
bit widths to bigger bit widths. Without replication logic, the color
component would be shifted and the least significant bits would be left
at 0, whereas with replication logic, the least significat bits will be
filled with the most significant bit.
For some reason omapdrm leaves replication logic always to off, which,
in the most common case, means that showing 16-bit RGB colors on 24-bit
display gives a bit darker colors than expected.
The reset value of the replication logic bit is enabled, and it should
always be set, as there's no practical reason to disable it. This patch
removes the option to disable it from omapdrm, and always sets it to
enabled in dispc.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omapdrm now uses dispc_ops instead of direct function calls so we can
remove all EXPORT_SYMBOLs from dispc. Most of the functions can also be
made static, but a few are used outside dispc.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We want to change the dispc API from plain functions to a struct with
functions pointers, so that omapdrm can call either omapdss or omapdss6
depending on the platform.
This patch adds 'struct dispc_ops' and adds functions to omapdss-base
to set and get the ops.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdrm still uses a few non-dispc functions: dss_feat_get_num_mgrs(),
dss_feat_get_num_ovls() and dss_feat_get_supported_color_modes(). We
want to provide omapdrm a single dispc_ops function pointer struct so
that omapdrm will use either the current omapdss or the new omapdss6
driver depending on the platform.
Those three functions are really dispc functions, but are located in the
dss_features.c for legacy reasons.
This patch adds similar functionss to the dispc, and changes omapdrm to
use those new functions. Underneath the functions still call the
functions from dss_feature.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch moves the common parts of omapdss to omapdss-base so that
both the current omapdss driver and the new omapdss6 driver can use
them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdss_is_initialized() is used to find out if omapdss has been probed
successfully. This patch moves the related code to the common
omapdss-base module, so that the same support will be there for both
omapdss and omapdss6.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdrm DSS manager enable/disable operations check the DSS manager
state to avoid double enabling/disabling. Check the CRTC software state
instead to decrease the dependency of the DRM layer to the DSS layer.
The dispc_mgr_is_enabled() function then be turned into a static
function, but needs to be moved up in its compilation unit to avoid a
forward declaration.
Add a WARN_ON to catch double enable or disable that should be prevented
by the DRM core and would be a clear sign of a bug. The warning should
eventually be removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use 'vm' to refer to a struct videomode instead of 'p', 't', 'timings' or
something else.
The code will be easier to follow if we use consistent names.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_video_timings can be replaced with the generic videomode in omapdrm
and the omap_video_timings can be removed.
This patch will replace the omap_video_timings with videomode.
With the change we no longer need the functions to convert to/from
videomode and drm_display_mode to omap_video_timings, these can be removed
as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_video_timings struct have the same members as struct videomode, but
their types are different. As first step change the types of the
omap_video_timings struct members to match their counterpart in
struct videomode to catch any type cast related issues.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for sync edge.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for pixel data edge.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for double_pixel mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for DE level.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information use display_flags for h/vsync level.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove the interlace member and add display_flags to omap_video_timings to
configure the interlace mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information rename the vbp member to vback_porch.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information rename the vfp member to vfront_porch.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information rename the vsw member to vsync_len.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information rename the hbp member to hback_porch.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In preparation to move the stack to use the generic videmode struct for
display timing information rename the hfp member to hfront_porch.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>