To make it easier to share ath10k_core_fetch_board_data_api_n() with testmode.c
refactor all firmware components to struct ath10k_fw_components. This structure
will hold firmware related files, for example firmware-N.bin and board-N.bin.
For firmware-N.bin create a new struct ath10k_fw_file which contains the actual
firmware image as well as the parsed data from the image.
Modify ath10k_core_start() to take struct ath10k_fw_components() as an argument
which makes it possible in following patches to drop some ugly hacks from
testmode.c.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return value is incorrect for btcoex and peer stats debugfs
'write' entries if the user provides a value that matches with
the already available debugfs entry, this results in the debugfs
entry getting stuck and the operation has to be terminated manually.
Fix this by returning the appropriate return 'count' as we do it for
other debugfs entries like pktlog etc.
Fixes: cc61a1bbbc ("ath10k: enable debugfs provision to enable Peer Stats feature")
Fixes: c28e6f06ff ("ath10k: fix sanity check on enabling btcoex via debugfs")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Provide a debugfs entry to enable/ disable Peer Stats feature.
Peer Stats feature is for developers/users who are more interested
in studying in Rx/Tx stats with multiple clients connected, hence
disable this by default. Enabling this feature by default results
in unneccessary processing of Peer Stats event for every 500ms
and updating peer_stats list (allocating memory) and cleaning it up
ifexceeds the higher limit and this can be an unnecessary overhead
during long run stress testing.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_download_cal_dt() compares obtained cal data content length
against QCA988X_CAL_DATA_LEN (2116 bytes). It was written by keeping
qca988x in mind. In fact, cal data length is more chip specific.
To make ath10k_download_cal_dt() more generic and reusable for other
chipsets (like qca4019), cal data length is moved to hw_params.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If device failed to init during early probing
(which is quite rare) it triggered driver to
compute crc before ar->firmware was ready causing
an oops.
Fixes: 3e58044b61 ("ath10k: print crc32 checksums for firmware and board files")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is observed that, we are disabling the packet log if we write same
value to the pktlog_filter for the second time. Always enable pktlogs
on non zero filter.
Fixes: 90174455ae ("ath10k: add support to configure pktlog filter")
Cc: stable@vger.kernel.org
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
First check for the device state before enabling / disabling
btcoex, also return a proper error value. Enabling / disabling
btcoex ideally does a f/w + ath10k_core_restart so the checks
that are applicable for 'simulate_fw_crash' shall be applicable
for this as well
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We periodically receive f/w stats event for updating
the rx duration and there is no reason to keep on appending
the f/w stats peer list, as this gets completely cleaned up when
the user polls for f/w stats {pdev, vdev, peer stats}. Only don't
print the warning message in the case PEER_STATS service is enabled
Fixes: 856e7c3 ("ath10k: add debugfs support for Per STA total rx duration")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We are not updating peer stats rx_duration periodically
unless the user one polls for fw_stats, this is because
we discard the update event since pdev list is empty. Fix
this by updating rx duration periodically irrepective of checks
for pdev list (irrespective of ping-pong response)
Fixes: 856e7c3 ("ath10k: add debugfs support for Per STA total rx duration")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
len has been initialized with a value of 0 and buf_len with 4096. There
is no way that this condition (len > buf_len) can be true now.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add debugfs support for per client total rx duration, track this
via the report of Peer stats rx duration reported for every 500ms
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable support for periodic peer stats update when peer stats
service is enabled. The host to update the peer stats received
from the firmware periodically, since firmware will reset this to zero
after sometime (due to memory constraints)
While enabling periodic peer / vdev stats cleanup the existing
list in debugfs if max limit is reached, so that the new stats is
updated.
Ideally speaking based on 'Michal Kazior's' suggestion
we need to completely move to periodic update of all the stats making
the 'ping - pong' method obselete. This requires a bit of re-work and
some testing as well, also confirmation regarding backward comptability
for various firmware and chipsets. Hence allow periodic update only
for peer_stats.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Prerequisite patch to address checkpatch errors for the next patch
in this series, this function names are bit too long, make it short
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The default values of max_num_amsdu / max_num_amdpu is assigned a
default value as part of 'ath10k_core_init_firmware_features'
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When debugging firmware problems it's useful to check checksums of each
component. Add a debugfs interface to retrieve crc32 checksums:
# cat /sys/kernel/debug/ieee80211/phy0/ath10k/fw_checksums
firmware-N.bin cc3fb466
athwlan c0089f21
otp f3efeb4f
codeswap 00000000
board-N.bin bebc7c08
board bebc7c08
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Earlier we printed all the info messages after a successful device
initialisation and firmware boot, but that's problematic if something goes
wrong and there's no easy way to know what firmware version was used and so on.
Split the info messages into smaller pieces and print them as soon as we have
the info available.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix write permission for few of the debugfs entries
which support write file operations as well.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As not all QCA98XX radios are not connected to Bluetooth modules, enabling the
BT coex feature in firmware will have side effects if the radio's GPIO are
connected with other (non-BT) HW modules. Add debugfs file to control the
firmware BT coex logic and set the feature as disable by default to avoid that
btcoex is accidentally enabled.
To enable this feature, execute:
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/btcoex
To disable:
echo 0 > /sys/kernel/debug/ieee80211/phyX/ath10k/btcoex
The firmware support this feature since 10.2.4.54 on 2G-only board, dual band
or 5G boards don't support this. The feature's name is WMI_SERVICE_COEX_GPIO
and the btcoex file is not created if firmware doesn't support it.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
[kvalo@qca.qualcomm.com: use btcoex filename and other smaller fixes]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The patch makes debug stats prints fw specific by adding a new member
in wmi_ops. That way it's easier to add fw_stats support to 10.4 firmware.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Tamizh Chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA99X0 uses radio specific board names based on chip id and
board id combinations. We get these IDs from the target using BMI after otp.bin
has been started.
This patch reorders the call to the function ath10k_core_fetch_board_file
so that we have OTP binary before requesting for boardid-chipid. We get this
OTP data after parsing firmware-N.bin.
[kvalo@qca.qualcomm.com: try BMI_PARAM_GET_EEPROM_BOARD_ID with
all boards and detect if command is not supported]
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA6174 needs different board files based on board type. To make it easier to
distribute multiple board files and automatically choose correct board file
create a simple TLV file format following the same principles as with FW IEs.
The file is named board-2.bin and contain multiple board files. Each board file
then can have multiple names.
ath10k searches for file board-N.bin (where N is the interface version number
for the board file, just like we for firmware files) in /lib/firmware/*, for
example for qca99x0 it will try to find it here:
/lib/firmware/ath10k/QCA99X0/hw2.0/board-2.bin
If ath10k doesn't find board-2.bin then it will fallback to the old board.bin file.
This patch adds a simple name scheme using pci device id which for now will be
used by qca6174:
bus=%s,vendor=%04x,device=%04x,subsystem-vendor=%04x,subsystem-device=%04x
This removes the old method of having subsystem ids in ar->spec_board_id and
using that in the board file name.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
[kvalo@qca.qualcomm.com: simplified the file format, rewrote commit log, other smaller changes]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The Transmit Power Control (TPC) dump will show the power control values for
each rate which makes it easier to debug calibration problems.
Example usage:
# cat /sys/kernel/debug/ieee80211/phy0/ath10k/tpc_stats
TPC config for channel 5180 mode 10
CTL = 0x10 Reg. Domain = 58
Antenna Gain = 1 Reg. Max Antenna Gain = 0
Power Limit = 34 Reg. Max Power = 34
Num tx chains = 3 Num supported rates = 155
**********CDD POWER TABLE*******
No. Preamble Rate_code tpc_valu1 tpc_value2 tpc_value3
0 CCK 0x40 0 0 0
1 CCk 0x41 0 0 0
[...]
154 HTCUP 0x 0 24 0 0
**********STBC POWER TABLE******
No. Preamble Rate_code tpc_valu1 tpc_value2 tpc_value3
0 CCK 0x40 0 0 0
[...]
154 HTCUP 0x 0 24 24 0
**********TXBF POWER TABLE******
is used to dump the tx power control stats.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If .pull_fw_stats() fails for some reason while processing
fw stats event, collected pdev/vdev/peer stats just before
the failure should be freed. This is unlikely to happen,
just code review catch.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If firmware did not have any feature flags set the
var would be left with values found on the stack
(i.e. garbage) yielding print string like this:
(...) features \xffffffa6m:^R\xfffffffbԂ\xffffffc4^E
Fixes: b27bc5a40f ("ath10k: dump fw features during probing")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch enables raw Rx/Tx encap mode to support software based
crypto engine. This patch introduces a new module param 'cryptmode'.
cryptmode:
0: Use hardware crypto engine globally with native Wi-Fi mode TX/RX
encapsulation to the firmware. This is the default mode.
1: Use sofware crypto engine globally with raw mode TX/RX
encapsulation to the firmware.
Known limitation:
A-MSDU must be disabled for RAW Tx encap mode to perform well when
heavy traffic is applied.
Testing: (by Michal Kazior <michal.kazior@tieto.com>)
a) Performance Testing
cryptmode=1
ap=qca988x sta=killer1525
killer1525 -> qca988x 194.496 mbps [tcp1 ip4]
killer1525 -> qca988x 238.309 mbps [tcp5 ip4]
killer1525 -> qca988x 266.958 mbps [udp1 ip4]
killer1525 -> qca988x 477.468 mbps [udp5 ip4]
qca988x -> killer1525 301.378 mbps [tcp1 ip4]
qca988x -> killer1525 297.949 mbps [tcp5 ip4]
qca988x -> killer1525 331.351 mbps [udp1 ip4]
qca988x -> killer1525 371.528 mbps [udp5 ip4]
ap=killer1525 sta=qca988x
qca988x -> killer1525 331.447 mbps [tcp1 ip4]
qca988x -> killer1525 328.783 mbps [tcp5 ip4]
qca988x -> killer1525 375.309 mbps [udp1 ip4]
qca988x -> killer1525 403.379 mbps [udp5 ip4]
killer1525 -> qca988x 203.689 mbps [tcp1 ip4]
killer1525 -> qca988x 222.339 mbps [tcp5 ip4]
killer1525 -> qca988x 264.199 mbps [udp1 ip4]
killer1525 -> qca988x 479.371 mbps [udp5 ip4]
Note:
- only open network tested for RAW vs nwifi performance comparison
- killer1525 (qca6174 hw2.2) is 2x2 device (hence max 866mbps)
- used iperf
- OTA, devices a few cm apart from each other, no shielding
- tcpX/udpX, X - means number of threads used
Overview:
- relative Tx performance drop is seen but is within reasonable and
expected threshold (A-MSDU must be disabled with RAW Tx)
b) Connectivity Testing
cryptmode=1
ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta2br1vlan OK
ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta2br1vlan OK
ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta2br1vlan OK
ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br1vlan OK
Note:
- each test takes all possible endpoint pairs and pings
- each pair-ping flushes arp table
- ip6 is used
c) Testbed Topology:
1ap1sta:
[ap] ---- [sta]
endpoints: ap, sta
1ap1sta2br:
[veth0] [ap] ---- [sta] [veth2]
| | | |
[veth1] | \ [veth3]
\ / \ /
[br0] [br1]
endpoints: veth0, veth2, br0, br1
note: STA works in 4addr mode, AP has wds_sta=1
1ap1sta2br1vlan:
[veth0] [ap] ---- [sta] [veth2]
| | | |
[veth1] | \ [veth3]
\ / \ /
[br0] [br1]
| |
[vlan0_id2] [vlan1_id2]
endpoints: vlan0_id2, vlan1_id2
note: STA works in 4addr mode, AP has wds_sta=1
Credits:
Thanks to Michal Kazior <michal.kazior@tieto.com> who helped find the
amsdu issue, contributed a workaround (already squashed into this
patch), and contributed the throughput and connectivity tests results.
Signed-off-by: David Liu <cfliu.tw@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Tested-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HTT version itself isn't sufficient to know what
HTT version given firmware blob uses. Hence print
the recently introduced HTT op version code.
While at it make the info string a bit more
consistent and clear.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This should help when analysing problems from
users and spot fw api blob problems easier.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some devices differ slightly and require different
board files. If wrong board data is used they
crash or behave incorrectly.
These devices can be differentiated by looking at
PCI subsystem device id. That is the case for
qca61x4 devices at least.
The board specific filename is constructed as:
board-<bus>-<id>.bin
For PCI in particular it is:
board-pci-<vendor>:<dev>:<subsys_vendor>:<subsys_dev>.bin
These files are looked in device/hw specific
directories. Hence for Killer 1525 (qca6174 hw2.1)
ath10k will request:
/lib/firmware/ath10k/QCA6174/hw2.1/board-pci-168c:003e:1a56:1525.bin
To not break any existing setups (e.g. in case
some devices in the wild already have subsys ids)
if a board specific file isn't found a generic one
is used which is the one which would be used until
now. This guarantees that after upgrading a driver
device will not suddenly stop working due to
now-missing specific board file. If this is the
case a "fallback" string is appended to the info
string when driver boots.
Keep in mind this is distinct from cal-pci-*.bin
files which contain full calibration data and MAC
address. Cal data is aimed at systems where
calibration data is stored out of band, e.g. on
nand flash instead of device EEPROM - an approach
taken by some AP/router vendors.
Board files are more of a template and needs some
bits to be filled in by the OTP program using
device EEPROM contents.
One could argue to map subsystem ids to some board
design codename strings instead of using raw ids
when building the board filename. Using a mapping
however would make it a lot more cumbersome and
time consuming (due to how patches propagate over
various kernel trees) to add support for some new
device board designs. Adding a board file is a lot
quicker and doesn't require recompilation.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fix the regerssion introduced after "ath10k_wmi_requests_stats()
call to use more stat bits", both the 10.2.X FW and community FW 10.1.X
will return time out when access the fw_stats with the STAT_VDEV and
STAT_PDEV. Add the condition to use different fw_stats mask for different
FW versions.
Fixes: 7777d8c7ef ("ath10k: implement fw stats for wmi-tlv")
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added and the assignments fixed up.
Missing spaces 1*HZ -> 1 * HZ were also added along the way.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now that ANI is enabled by default, allow user to disable or enable ANI feature
from debugfs
echo 0|1 > /sys/kernel/debug/ieee80211/phyX/ath10k/ani_enable
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Thermal throttling is not handled in software restart and device
bootup. Also it needs to be configured whenever quiet period got
updated. Fix that.
Reported-by: Matthias Kaehlcke <mka@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support to configure quiet period (in milliseconds) via debugfs.
This is useful to experiment different quiet period values along with
different throttle ratio.
echo 100 > /sys/kernel/debug/ieee80211/phyX/ath10k/quiet_period
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This processes and pushes fw stats to the debug
module (if enabled).
Changing the generic ath10k_wmi_requests_stats()
call to use more stat bits has no effect on older
firmware binaries.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New qca6174 wmi-tlv firmware revisions support
more stat event bits.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New qca6174 wmi-tlv firmware supports vdev stats.
This patch adds support for it in the debug
frontend.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce an optional log level configuration for the existing debugfs fw_dbglog file. It
allows users to configure the desired log level for firmware dbglog messages.
To configure log level as WARN:
echo 0xffffffff 2 > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
The values are:
VERBOSE 0
INFO 1
WARN 2
ERR 3
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
wait_for_completion_timeout does not return negative values so the tests
for <= 0 are not needed and the case differentiation in the error handling
path unnecessary.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The internal firmware version doesn't tell much to the user, it's more
informative to use that field to print the wmi op version.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce a new wmi interface controls noise floor (NF) calibration
period via debugfs as firmware has introduced it on v10.2.
It allows users to modify frequency of NF calibration in millisecond
and changes RSSI reporting frequency consequently.
Short calibration period will trigger more frequent NF calibration,
so that RSSI reported in receive frames is more realistic.
Till now calibration was done at 30 seconds.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since the 10.x fw branch support was introduced it
became apparent ath10k will need to be able to
deal with different fw ABIs eventually.
The patch creates an abstraction for dealing with
command and event structures across different ABIs
and mostly gets rid of the
ATH10K_FW_FEATURE_WMI_10X flag usage.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The service bitmap can be used to determine
firmware capabilities.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The number of peers isn't directly translatable to
the number of stations because ath10k needs to
reserve a few extra peers for special cases like
multi-vif concurrency.
The previous limit was 126 and 15 stations in AP
mode for 10.x and main firmware branches
respectively. The limit is now 128 and 16 which
was the original intention.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add mem_val debugfs file for dumping the firmware (target) memory and also for
writing to the memory. The firmware memory is accessed through one file which
uses position of the file as the firmware memory address. For example, with dd
use skip parameter for the address.
Beucase target memory width is 32 bits it's strongly recommended to use
blocksize divisable with 4 when using this interface. For example, when using
dd use bs=4 to set the block size to 4 and remember to divide both count and
skip values with four.
To read 4 kB chunk from address 0x400000:
dd if=mem_value bs=4 count=1024 skip=1048576 | xxd -g1
To write value 0x01020304 to address 0x400400:
echo 0x01020304 | xxd -r | dd of=mem_value bs=4 seek=1048832
To read 4 KB chunk of memory and then write back after edit:
dd if=mem_value of=tmp.bin bs=4 count=1024 skip=1048576
emacs tmp.bin
dd if=tmp.bin of=mem_value bs=4 count=1024 seek=1048576
Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Debugfs files reg_addr and reg_val are used for reading and writing to the
firmware (target) registers. reg_addr contains the address to be accessed,
which also needs to be set first, and reg_value is when used for reading and
writing the actual value in ASCII.
To read a value from the firmware register 0x100000:
# echo 0x100000 > reg_addr
# cat reg_value
0x00100000:0x000002d3
To write value 0x2400 to address 0x100000:
# echo 0x100000 > reg_addr
# echo 0x2400 > reg_value
#
Signed-off-by: Yanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are better ways to get the kernel information, use the
utsname and omit the version code entirely since it's duplicate.
The version magic is rather useless anyway
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Until now it was possible to simulate soft and
hard fw crashes but it wasn't possible to trigger
an immediately hw restart itself (without the fw
crash).
This can be useful when stress testing hw
restarting stability, e.g. during heavy tx/rx
traffic.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
