Commit Graph

7 Commits

Author SHA1 Message Date
Heiko Schocher
830cb6fafc mpc5200: support for the MAN mpc5200 based board mucmc52
- serial Console on PSC1
- 64MB SDRAM
- MTD CFI Flash
- Ethernet FEC
- IDE support

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-10-15 09:33:24 -06:00
Heiko Schocher
371bc96b89 mpc5200: support for the MAN mpc5200 based board uc101
- serial Console on PSC1
- 64MB SDRAM
- MTD CFI Flash
- Ethernet FEC
- I2C with PCF8563 and Temp. Sensor ADM9240
- IDE support

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-10-15 09:29:32 -06:00
Wolfram Sang
10b9dc6f6b powerpc/5200: add Phytec phyCORE-MPC5200B-IO board (pcm032)
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-03-11 09:36:26 -06:00
Grzegorz Bernacki
bdad05489f powerpc/5200: Add support for the digsy MTC board.
Board support for the InterControl Digsy-MTC device based on the MPC5200B SoC.

Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-02-04 13:39:17 -07:00
s.hauer@pengutronix.de
106757b38f [POWERPC] mpc5200: add Phytec pcm030 board support
Add board support for the Phytec pcm030 mpc5200b based board. It
does not need any platform specific fixups and as such is handled
as a mpc5200 simple platform.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-04-29 07:17:12 -06:00
Grant Likely
c8004a2818 [POWERPC] Add common clock setting routine mpc52xx_psc_set_clkdiv()
PSC drivers should not access the CDM registers directly.  Instead provide
a common routine for setting the PSC clock parameters with the required
locking.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-01-26 15:32:18 -07:00
Marian Balakowicz
5b5820d08b [POWERPC] mpc5200: Add generic support for simple MPC5200 based boards
This patch adds support for 'mpc5200-simple-platform' compatible
boards which do not need a platform specific setup. Such boards
are supported assuming the following:

- GPIO pins are configured by the firmware,
- CDM configuration (clocking) is setup correctly by firmware,
- if the 'fsl,has-wdt' property is present in one of the
  gpt nodes, then it is safe to use such gpt to reset the board,
- PCI is supported if enabled in the kernel configuration
  and if there is a PCI bus node defined in the device tree.

Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-01-18 20:57:09 -07:00