When trying to set wow wakeup patterns it fails with this command:
iw phyxx wowlan enable patterns offset xx+ IP address xx.xx.xx.xx
The reason is that the wow pattern from upper layer is in 802.3 format
for this case, it need to convert it to 802.11 format. The input
offset parameter is used for 802.3, but the actual offset firmware
need depends on rx_decap_mode, so that it needs to be recalculated.
Pattern of 802.3 packet is not same with 802.11 packet. If the
rx_decap_mode is ATH10K_HW_TXRX_NATIVE_WIFI, then firmware will
receive data packet with 802.11 format from hardware.
Tested with QCA6174 hw3.0 with firmware
WLAN.RM.4.4.1-00099-QCARMSWPZ-1, but this will also affect QCA9377.
This has always failed, so it's not a regression with new firmware
releases.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ath10k reports the random_mac_addr capability to upper layer
based on the service bit firmware reported. Driver sets the
spoofed flag in scan_ctrl_flag to firmware if upper layer has
enabled this feature in scan request.
Test with QCA6174 hw3.0 and firmware-6.bin_WLAN.RM.4.4.1-00102-QCARMSWP-1,
but QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add WMI_SERVICE_AVAILABLE_EVENT to extend WMI_SERVICE_READY_EVENT,
the 128bit service map in WMI_SERVICE_READY_EVENT is not enough
for firmware to notice new WLAN service to host driver. Hereby,
for thoese new WLAN service, firmware will notice host driver by
WMI_SERVICE_AVAILABLE_EVENT.
Signed-off-by: Alan Liu <alanliu@codeaurora.org>
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add support to get RSSI from acknowledgment
frames for transmitted management frames.
hardware_used: QCA4019, QCA9984.
firmware version: 10.4-3.5.3-00052.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently vdev stats displayed in fw_stats are applicable
only for TLV based firmware and fix it for 10.4 firmware
as of now. The vdev stats in 10.4 firmware is split into two
parts (vdev_stats, vdev_stats_extended). The actual stats
are captured only in extended vdev stats. In order to enable
vdev stats, appropriate feature bit will be set on extended
resource config. As FTM related counters are available only on
newer 10.4 based firmware, these counters will be displayed
only on valid data.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable TDLS peer inactivity detetion feature.
QCA6174 firmware(version: WLAN.RM.4.4) support TDLS link inactivity detecting.
Set related parameters in TDLS WMI command to enable this feature.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Export the final Transmit Power Control (TPC) value, which is the
minimum of control power and existing TPC value to user space via
a new debugfs file "tpc_stats_final" to help with debugging.
It works with the new wmi cmd and event introduced in 10.4 firmware
branch.
WMI command ID: WMI_PDEV_GET_TPC_TABLE_CMDID
WMI event ID: WMI_PDEV_TPC_TABLE_EVENTID
cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats_final
$ cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats_final
TPC config for channel 5180 mode 10
CTL = 0x 0 Reg. Domain = 58
Antenna Gain = 0 Reg. Max Antenna Gain = 0
Power Limit = 60 Reg. Max Power = 60
Num tx chains = 2 Num supported rates = 109
******************* CDD POWER TABLE ****************
No. Preamble Rate_code tpc_value1 tpc_value2 tpc_value3
0 CCK 0x40 0 0
1 CCK 0x41 0 0
[...]
107 HTCUP 0x 0 46 46
108 HTCUP 0x 0 46 46
******************* STBC POWER TABLE ****************
No. Preamble Rate_code tpc_value1 tpc_value2 tpc_value3
0 CCK 0x40 0 0
1 CCK 0x41 0 0
[...]
107 HTCUP 0x 0 46 46
108 HTCUP 0x 0 46 46
***********************************
TXBF not supported
**********************************
The existing tpc_stats debugfs file provides the dump
which is minimum of target power and regulatory domain.
cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats
Hardware_used: QCA4019
Firmware version: firmware-5.bin_10.4-3.0-00209
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable TDLS wider bandwidth support for 5GHz based on firmware wmi capabilities.
This patch is required for chipset QCA9888. Tested with firmware version
10.4-3.5.1-00018.
Signed-off-by: Balaji Pothunoori <bpothuno@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HL1.0 firmware branch, used in wcn3990, transmits management
frames by reference over WMI.
Add support for management tx by reference over WMI.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Due to the limitation of wmi tlv parsing logic, if there are
two parameters in a wmi event with same tlv tag, we can get only
the last value, as it overwrites the prev value of the same tlv tag.
The service ready event in wcn3990 contains two parameters of the
same tag UINT32, due to which the svc bitmap is overwritten with the
DBS support parameter.
Refactor the service ready event parsing to allow parsing two tlv
of the same tag UINT32 for wcn3990.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 10.4 firmware defines this as a 3-bit field, as does the
mac80211 stack. The 4th bit is defined as CONF_IMPLICIT_BF
at least in the firmware header I have seen. This patch
fixes the ath10k wmi header to match the firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA99x0 and QCA4019 family chips support CCMP-256, GCMP-128, and
GCMP-256 ciphers in hardware, so advertise support for these. As
firmware does not support group management frame ciphers (BIP),
handle them in software (mac80211).
Reviewed-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI interface for all the firmwares(except QCA6174) does not include the
type of peer(default/bss/tdls) requested during peer creation, therefore
target creates a default peer.
TDLS implementation on 10.4 firmware requires host to configure the
peer type(tdls) for TDLS peers. This patch adds peer type parameter to the
existing WMI interface for peer creation to accommodate this requirement.
Tested this change on QCA9888(10.4-3.5.1-00018) and QCA988x(10.2.4.70.9-2)
with ping tests for AP/STA modes.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds the support of TDLS feature for 10.4 firmware
versions.
A new WMI service is added to advertise the support of TDLS for
10.4 firmwares.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Though there is room to accommodate 512 services in wmi service
ready event, target uses only first 4-bits of each 32-bit word for
advertising wmi services thereby limiting max wmi services to 64.
TDLS implementation for 10.4 firmwares introduces new wmi services by
making use of remaining unused bits of each 32-bit word, therefore the
wmi service mapping in host needs to be extended.
This patch adds the logic to extend the wmi SVCMAP to accommodate new
wmi services.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9984 hardware can do 4x4 at 80Mhz, but only 2x2 at 160Mhz.
First, report this to user-space by setting the max-tx-speed
and max-rx-speed vht capabilities.
Second, if the peer rx-speed is configured, and if we
are in 160 or 80+80 mode, and the peer rx-speed matches
the max speed for 2x2 or 1x1 at 160Mhz (long guard interval),
then use that info to set the peer_bw_rxnss_override appropriately.
Without this, a 9984 firmware will not use 2x2 ratesets when
transmitting to peer (it will be stuck at 1x1), because
the firmware would not have configured the rxnss_override.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[sven.eckelmann@openmesh.com: rebase, cleanup, drop 160Mhz workaround cleanup]
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
[kvalo@qca.qualcomm.com: use hw_params, rename the title]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix output from checkpatch.pl like:
Block comments use a trailing */ on a separate line
Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix typo (spelling mistake) in wmi.h
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If a 5 GHz radio is calibrated for operation in both
the low band (channels 36 to 64) and high band(channels 100 to 169),
hardware allows operations in all the listed channels. However,
if the chip has been calibrated only for the low/high band and
a high/low band channel is configured, due to lack of calibration
there will be potentially invalid signal on those non calibrated channels.
To avoid this problem this patch sets IEEE80211_CHAN_DISABLED flag for
those non calibrated channels by using low_5ghz_chan and high_5ghz_chan
values which we get from target through wmi service ready event.
Driver initialized flags are getting re initialized in handle_channel
in cfg80211. So calling the function to disable the non supported channel
from reg_notifier().
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
I wanted to take a look and it's apparently in other header
Signed-off-by: Amadeusz Sławiński <amadeusz.slawinski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch provides support to get per peer tids log.
echo 1 > /sys/kernel/debug/ieee80211/phyX/netdev\:wlanX/stations/
XX:XX/peer_debug_trigger
These logs will be the part of FWLOGS which we collect the logs
via tracing interface. Here we will get the peer tigd logs only
once(not repeatedly) when we write 1 to the debugfs file.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes new checkpatch warnings:
drivers/net/wireless/ath/ath10k/htt.h:1823: function definition argument 'struct sk_buff *' should also have an identifier name
drivers/net/wireless/ath/ath10k/wmi.h:6607: function definition argument 'struct wmi_start_scan_arg *' should also have an identifier name
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds full VHT160 support for QCA9984 chipsets Tested on Netgear
R7800. 80+80 is possible, but disabled so far since it seems to contain
glitches like missing vht station flags (this may be firmware or mac80211
related).
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
[kvalo@qca.qualcomm.com: refactoring and fix few warnings]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Per peer tx stats are part of 'HTT_10_4_T2H_MSG_TYPE_PEER_STATS'
event, Firmware sends one HTT event for every four PPDUs.
HTT payload has success pkts/bytes, failed pkts/bytes, retry
pkts/bytes and rate info per ppdu.
Peer stats are enabled through 'WMI_SERVICE_PEER_STATS',
which are nowadays enabled by default.
Parse peer stats and update the tx rate information per STA.
tx rate, Peer stats are tested on QCA4019 with Firmware version
10.4-3.2.1-00028.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Neither of these did the right thing:
- get_tsf just returned 0
- set_tsf assumed a simple offset was applied against
get_tsf(), which works, except in the case of
calculating TSF from rx_mactime (actual TSF).
Just remove them for now. We can reimplement set_tsf in
terms of TSF increment/decrement in the future if get_tsf
is ever supported by FW.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Current set_tsf is implemented in terms of TSF_INCREMENT
only. Instead support new WMI command TSF_DECREMENT and
export these through offset_tsf. Advantage is we get
more accurate TSF adjustments, and don't calculate wrong
offset in case absolute TSF was calculated from rx_mactime
(actual TSF).
The new WMI command is available in firmware
10.4-3.2.1-00033 for QCA4019 chips. Old drivers on new
firmware or vice versa shouldn't be a problem since
get/set tsf logic was already broken.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
They are not necessarily named in an intuitive manner,
so at least add some comments to help the next person.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Correct some trivial comment typos.
Remove unnecessary parentheses in a long line.
Signed-off-by: Joe Perches <joe@perches.com>
[kvalo@qca.qualcomm.com: drop the change for return]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For 10.4 fw versions, dbglog module id has been extended from u32
to u64, hence this patch fixes the same in the ath10k driver side.
This patch doesn't break the older 10.4 releases. The FW change
is already present in the older FWs.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI_SERVICE_PERIODIC_CHAN_STAT_SUPPORT service has missed in
the commit 7e247a9e88 ("ath10k: add dynamic tx mode switch
config support for qca4019"). This patch adds the service to
avoid mismatch between host and target.
Fixes: 7e247a9e88 ("ath10k: add dynamic tx mode switch config support for qca4019")
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows placing command barriers for explicit
serializing and synchronizing state.
Useful for future driver development.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Will be useful for implementing command barriers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 'extended peer stats' will be not be appended with normal peer stats
data and they shall be coming in separate chunks. Fix this by maintaining
a separate linked list 'extender peer stats' for 10.4 and update
rx_duration for per station statistics. Also parse through beacon filter
(if enabled), to make sure we parse the extended peer stats properly.
This issue was exposed when more than one client is connected and
extended peer stats for 10.4 is enabled
The order for the stats is as below
S - standard peer stats, E- extended peer stats, B - beacon filter stats
{S1, S2, S3..} -> {B1, B2, B3..}(if available) -> {E1, E2, E3..}
Fixes: f9575793d4 ("ath10k: enable parsing per station rx duration for 10.4")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 firmware has support to enable or disable btcoex functionality
without reloading firmware via wmi pdev param. Add provision to send
pdev param command via existing btcoex knob.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add handler to process bss channel information wmi event that
will be received upon sending pdev_chan_info_request wmi command.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI ops to send pdev_bss_chan_info_request command to target.
This command will be used to retrieve updated cycle counters and noise
floor value of current operating channel (bss channel).
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI definitions for pdev bss channel information request and
event.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA6174 WLAN.RM.2.0 firmware uses max_tx_power instead of using max_reg_power
to set transmission power. The tx power was about -50dbm, after applying this
change, it become -32dbm.
Signed-off-by: Alan Liu <alanliu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
push-pull mode needs certain amount the host driver involvement for
managing queues in the host memory and packet delivery to firmware.
qca4019 wifi firmware has an option to stay in push mode for less
number of active traffic flow and then switch to push-pull mode when
the active traffic flow goes beyond the certain limit.
The advantage of staying in push mode for less active traffic is, the
host cpu consumption is reduced. qca4019 firmware supports this
flexibility of the mode switch. It takes the host driver interest
(LOW_PERF/HIGH_PERF) via WMI_EXT_RESOURCE_CFG_CMDID,
LOW_PERF - fw would stay in push mode and switch to push-pull
based on demand.
HIGH_PERF - fw would stay in push-pull mode from the boot.
To make this configuration generic, new WMI services
WMI_SERVICE_TX_MODE_PUSH_ONLY, WMI_SERVICE_TX_MODE_PUSH_PULL,
WMI_SERVICE_TX_MODE_DYNAMIC are introduced to take dynamic tx mode
switch support availability in firmware.
Based on WMI_SERVICE_TX_MODE_DYNAMIC, LOW_PERF or HIGHT_PERF is
configured to the firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix checkpatch warnings about use of spaces with operators:
spaces preferred around that '*' (ctx:VxV)
This has been recently added to checkpatch.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Update 10.4 WMI vdev param to sync to current 10.4 firmware
as of 2/23/2016.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.2.4.70.24 firmware introduces new feature to set TSF
via vdev parameter, hence implement relevant function.
set_tsf function can be used to shift TBTT that will
help avoid its clockdrift which happens when beacons
are collided.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will help anyone trying to use the ack-rssi reporting
feature with the host-specified TX-rate option in 10.4 firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rx duration support for per station is part of extended peer
stats, enable provision to parse the same and provide backward
compatibility based on the 'stats_id' event
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add API support for Extended Resource Configuration for 10.4. This
is useful to enable new features like Peer Stats, LTEU etc if the
firmware advertises support for the service. This is also done to
provide backward compatibility with older firmware. Also for clarity
send default host platform type as 'WMI_HOST_PLATFORM_HIGH_PERF',
though this should not make any difference in functionality
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Check and set Rx MAC timestamp when firmware indicates it.
Firmware adds it in Rx beacon frame only at this moment.
Driver and mac80211 may utilize it to detect such clockdrift
or beacon collision and use the result for beacon collision
avoidance.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some of the parameter like tx/rx chain mask, number of htt tx desc,
qcache active peer count, etc goes via wmi init cmd to qca4019 firmware
are different.
To make use of 10.4 gen_init function for qca4019, change wmi service
ready handler and 10.4 wmi init functions to adapt qca4019 specific
init values.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
