If the GPMC probe fails, devices that use the GPMC (such as ethernet
chips, flash memories, etc) can still allocate a GPMC chip-select and
register the device. On the OMAP2420 H4 board, this was causing the
kernel to crash after the gpmc probe failed and the board attempted
to start networking. Prevent this by marking all the chip-selects as
reserved by default and only make them available for devices to request
if the GPMC probe succeeds.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
for_each_node_by_name() automatically calls of_node_put() on each
node passed; so don't do it explicitly unless there's an error.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
LCDC clock node is a one that does not have set rate capability. It
just passes on the rate that is sent downstream by it's parent. While
lcdc clock parent and it's grand parent - dpll_disp_m2_ck and
dpll_disp_ck has the capability to configure rate.
And the default rates provided by LCDC clock's ancestors are not
sufficient to obtain pixel clock for current LCDC use cases, hence
currently display would not work on AM335x SoC's (with driver
modifications in platfrom independent way).
Hence inform clock framework to propogate set rate for LCDC clock as
well as it's parent - dpll_disp_m2_ck. With this change, set rate on
LCDC clock would get propogated till dpll_disp_ck via dpll_disp_m2_ck,
hence allowing the driver (same driver is used in DaVinci too) to set
rates using LCDC clock without worrying about platform dependent clock
details.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DEFINE_STRUCT_CLK does not have the capability to set flags, define
DEFINE_STRUCT_CLK_FLAGS to handle flags. This is needed to add
SET_RATE_PARENT flag in statically defined lcd clock in am335x.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The core functionality of the arch_timer driver is not directly tied to
anything under arch/arm, and can be split out.
This patch factors out the core of the arch_timer driver, so it can be
shared with other architectures. A couple of functions are added so
that architecture-specific code can interact with the driver without
needing to touch its internals.
The ARM_ARCH_TIMER config variable is moved out to
drivers/clocksource/Kconfig, existing uses in arch/arm are replaced with
HAVE_ARM_ARCH_TIMER, which selects it.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
This series is a prerequisite for the functional powerdomain
conversion series.
Basic test logs for this branch are here:
http://www.pwsan.com/omap/testlogs/pm_cleanup_fixes_3.9/20130129150017/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=/cy+
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-b-for-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.9/pm
Several OMAP2+ power management fixes, optimizations, and cleanup.
This series is a prerequisite for the functional powerdomain
conversion series.
Basic test logs for this branch are here:
http://www.pwsan.com/omap/testlogs/pm_cleanup_fixes_3.9/20130129150017/
* Move sp810 header to a more generic location,
mainly to share it with arm64
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRCULAAAoJEL9jRaJfXa5PyysH/AsFbihoAGU0S7o+ggyN4S8m
5myEfbdMvgI5Hjcl/MgcVJAl6jFpDjmBH5ZPu+o8WzoP5L91C9F//kMRZqK0zATj
Y2OdMVNfVQG94bSsmjHryWF8W0RYcY2bQr0wJmgguNDpRLFsFdF3Rb58AWzG+2tP
KFxDg9u/CyhC/sv7BzoKI+J3ol5wEmv4BNMbPyjYG8L5TcBfe/IZqnl6KZ/QAw5i
QUFs3oXtT4/v8bnsxAym+VXIvjSHWs2t0CivfMyH+ZIgb3NbfJ1gIOCOJIk5XWTu
6L1yYyBBcRr60y9p4s2Nd4NxHZEB7pyZYuboUOxSmRNnEM54RT2Nkvcdon8j6Rw=
=uB7w
-----END PGP SIGNATURE-----
Merge tag 'vexpress/drivers-for-3.9' of git://git.linaro.org/people/pawelmoll/linux into next/drivers
From Pawel Moll:
Versatile Express related driver updates for 3.9:
* Move sp810 header to a more generic location,
mainly to share it with arm64
* tag 'vexpress/drivers-for-3.9' of git://git.linaro.org/people/pawelmoll/linux:
arm: Move sp810.h to include/linux/amba/
+ Linux 3.8-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix some whitespace problems introduced by commit
da03ce65b5 ("OMAP3: powerdomain data:
add voltage domains"). Also, improve the documentation for the struct
powerdomain.flags field.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
The atomic usecounts seem to be confusing, and are no longer needed
since the operations that they are attached to really should take
place under lock. Replace the atomic counters with simple integers,
protected by the enclosing powerdomain spinlock.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Split the clkdm_(add|del)_(wk|sleep)dep() functions into lockless and
locking versions -- this will be needed in a subsequent patch. Also,
while here, remove the leading underscore, since these are not
currently static functions. And for functions that have
kerneldoc-style comment blocks, but which are missing the initial
'/**' tag, fix the tag to indicate that they are kerneldoc.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
There's no need to preserve the autodep handling code in
mach-omap2/cm2xxx.c, since no autodeps are defined for these chips.
Hopefully they'll never be needed, but if in some future case they are,
this code can be added back in.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add a per-powerdomain spinlock. Use that instead of the clockdomain
spinlock. Add pwrdm_lock()/pwrdm_unlock() functions to allow other
code to acquire or release the powerdomain spinlock without reaching
directly into the struct powerdomain.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jean Pihet <jean.pihet@newoldbits.com>
Move omap_set_pwrdm_state() from the PM code to the powerdomain code,
and refactor it to split it up into several functions. A subsequent patch
will rename it to conform with the existing powerdomain function names.
This version includes some additional documentation, based on a
suggestion from Jean Pihet. It also modifies omap_set_pwrdm_state()
to not bail out early unless both the powerdomain current power state
and the next power state are equal. (Previously it would terminate
early if the next power state was equal to the target power state,
which was insufficiently rigorous.)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tero Kristo <t-kristo@ti.com>
Drop an unnecessary pwrdm_wait_transition() from mach-omap2/pm.c -
it's called by the subsequent pwrdm_state_switch().
Also get rid of pwrdm_wait_transition() in the powerdomain code - there's
no longer any need to export this function.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Don't attempt to put clockdomains to sleep; this should be handled by the
clock framework. It should be enough to program the next-power-state,
and then let the code in omap_pm_clkdms_setup() deal with the rest.
Start out by programming the MPU and CORE powerdomains to stay ON.
Then control the MPU and CORE powerdomain states directly in
omap2_enter_full_retention() and omap2_enter_mpu_retention(). Not the
most optimal way to do it, but certainly is the most conservative until
OMAP2xxx PM is working again.
Get rid of the open-coded PM_PWSTCTRL_MPU writes in
omap2_enter_mpu_retention(); use the powerdomain code instead.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
In clkdm_sleep(), the powerdomain should be eligible to switch power
states right after the call to the low-level clockdomain sleep
function. We should have been tracking that with the
pwrdm_state_switch() code, but we weren't, for whatever reason. Fix that.
This resolves the "pwrdm state mismatch(cam_pwrdm) 3 != 0" that appears
during the OMAP4460 Pandaboard-ES PM test, e.g. here:
http://www.pwsan.com/omap/testlogs/test_v3.8-rc5/20130126003323/pm/4460pandaes/4460pandaes_log.txt
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Fix the trace in the case a power domain did not hit the desired
state, as reported by Paul Walmsley.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
[paul@pwsan.com: split this fix off from the patch
"ARM: OMAP2+: PM debug: trace the functional power domains states"]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Avoid programming the MPU and CORE powerdomain next-power-state
registers if those powerdomains will never enter low-power states
(e.g., the state that people refer to as "C1").
To avoid making assumptions about CPUIdle states based on their order
in the list, use a flag to mark CPUIdle states that don't enter
powerdomain low-power states.
Avoid a previous-power-state register read on the MPU powerdomain
unless we know that the MPU was supposed to go OFF during the last
state transition. Previous-power-state register reads can be very
expensive, so it's worth avoiding these when possible.
Since the CORE_L3 clockdomain can't go inactive unless the MPU is active,
there's little point blocking autoidle on the CORE_L3 clockdomain in "C1"
state, since we've programmed the MPU clockdomain to stay active.
Remove the unnecessary code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Drop the define and make use of scu_a9_get_base() which reads
the physical address of SCU from CP15 register.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This driver is simple, uses the latest interfaces and contains few if
any controversial elements. All of its interfaces have been in place
for a long time now. Hence let's move it out of staging.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Peter Meerwald <pmeerw@pmeerw.net>
Use the HWMOD_BLOCK_WFI flag in the hwmod data to prevent the MPU from
entering WFI when the I2C devices are active. No idea why this is needed;
this could certainly bear further investigation if anyone is interested.
The objective here is to remove some custom code from the OMAP24xx PM
code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Apparently, on some OMAPs, the MPU can't be allowed to enter WFI while
certain peripherals are active. It's not clear why, and it's likely
that there is simply some other bug in the driver or integration code.
But since the likelihood that anyone will have the time to track these
problems down in the future seems quite small, we'll provide a
flag, HWMOD_BLOCK_WFI, to mark these issues in the hwmod data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP3xxx CPUIdle driver contains some code to place a lower bound
on the PER powerdomain's power state. Convert this code to a data-driven
implementation to remove branches and to improve readability.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Add the possible logic retention states for the 24xx CORE powerdomain.
Subsequent patches use this data to avoid returning incorrect data, by
skipping reads from register bitfields that don't actually exist.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Remove some clocks that don't appear to be used by anything
and which are not associated with any hardware registers.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Convert all DEFINE_OMAP_MUX_GATE() combinations that list MODULEMODE
registers in their gate arguments to DEFINE_OMAP_MUX(), dropping the
MODULEMODE data. This is possible because the MODULEMODE bits control
IP blocks, not clocks; and the hwmod code takes care of IP block
control. Rename these clocks to reflect the original multiplexer name
as specified in the comments. And convert the hwmod data to use the
multiplexer clock name.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Mike Turquette <mturquette@linaro.org>
Remove some leaf "clocks" that are actually IP block idle control
points, since these should now be handled by the hwmod code.
There are still a few types of MODULEMODE clocks that need to be
cleaned up:
- those still in use by driver or integration code
- those in DEFINE_CLK_OMAP_MUX_GATE() blocks; the gate portion of
these should be removed
A similar process may also be possible on OMAP2/3.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Mike Turquette <mturquette@linaro.org>
Remove now-obsolete code from arch/arm/mach-omap2/omap_device.c. This
mostly consists of removing the first attempt at device PM latency
handling. This was never really used, has been replaced by the common
dev_pm_qos code, and needs to go away as part of the DT conversion.
Also, the early platform_device creation code has been removed, as it
appears to be unused.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
The text in Documentation said it would be removed in 2.6.41;
the text in the Kconfig said removal in the 3.1 release. Either
way you look at it, we are well past both, so push it off a cliff.
Note that the POWER_CSTATE and the POWER_PSTATE are part of the
legacy tracing API. Remove all tracepoints which use these flags.
As can be seen from context, most already have a trace entry via
trace_cpu_idle anyways.
Also, the cpufreq/cpufreq.c PSTATE one is actually unpaired, as
compared to the CSTATE ones which all have a clear start/stop.
As part of this, the trace_power_frequency also becomes orphaned,
so it too is deleted.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cam_mclk clock is generated through the following clocks chain:
dpll4 -> dpll4_m5 -> dpll4_m5x2 -> cam_mclk
As dpll4_m5 and dpll4_m5x2 do not driver any clock other than cam_mclk,
back-propagate the cam_clk rate changes up to dpll4_m5.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Tested-by: Sakari Ailus <sakari.ailus@iki.fi>
The pin in question is muxed between GPIO7 and PWM1. For backlight control
there is a custom code in board-zoom-display to control the backlight.
No need to request the GPIO7 - which was failing since the way it is
requested no longer valid: twl's gpio range is allocated dynamically.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
With the PWM backed driver the PMU_STAT led's brighness can be controlled.
This needs the new drivers for the TWL PWM/LED to work.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
New PWM drivers are being prepared for twl series which will enable the use
of all PWMs (PWMs and LEDs).
They are implemented as generic PWM drivers to be able to use them for different
purposes.
The current platform code was broken: the leds_pwm driver was not able to pick
up the PWM since the pwm_id was incorrect.
With the other patches we will be able to control the followings:
LCD backlight via pwm-backlight driver
Keypad leds via leds_pwm driver as normal LED
Charging indicator via leds_pwm driver as normal LED
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Boards with special audio routing can pass a custom omap_tw4030_pdata to the
audio machine driver.
At the same time update the board files using the same audio driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Select the most commonly used audio configuration on boards with twl4030
audio:
Headset, Handsfree output and Line in input
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
The HS extmute is not used on Zoom2 boards. Furthermore the GPIO153 is used
as IRQ for the TSC2004 touchscreen controller - for which we do not have
driver upstream, yet.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Add the UART2 muxing data to the board file (this used to be,
erroneously, done in the bootloader).
Cc: stable <stable@vger.kernel.org> [3.7]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The iterator correctly handles of_node_put() calls.
Remove it before continue'ing the loop.
Without this patch you get the following with
CONFIG_OF_DYNAMIC set:
ERROR: Bad of_node_put() on /ocp/timer@44e31000!
[<c001329c>] (unwind_backtrace+0x0/0xe0) from [<c03dd8f0>] (of_node_release+0x2c/0xa0)!
[<c03dd8f0>] (of_node_release+0x2c/0xa0) from [<c03ddea0>] (of_find_matching_node_and_match+0x78/0x90)!
[<c03ddea0>] (of_find_matching_node_and_match+0x78/0x90) from [<c06d349c>] (omap_get_timer_dt+0x78/0x90)!
[<c06d349c>] (omap_get_timer_dt+0x78/0x90) from [<c06d3664>] (omap_dm_timer_init_one.clone.2+0x34/0x2bc)!
[<c06d3664>] (omap_dm_timer_init_one.clone.2+0x34/0x2bc) from [<c06d3a2c>] (omap2_gptimer_clocksource_init.clone.4+0x24/0xa8)!
[<c06d3a2c>] (omap2_gptimer_clocksource_init.clone.4+0x24/0xa8) from [<c06cca58>] (time_init+0x20/0x30)!
[<c06cca58>] (time_init+0x20/0x30) from [<c06c9690>] (start_kernel+0x1a8/0x2fc)!
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Jon Hunter <jon-hunter@ti.com>
[tony@atomide.com: updated description per Jon]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we will get:
WARNING: vmlinux.o(.text+0x1d4f0): Section mismatch in reference from the
function omap_init_ocp2scp() to the function .init.text:omap_device_build()
The function omap_init_ocp2scp() references
the function __init omap_device_build().
This is often because omap_init_ocp2scp lacks a __init
annotation or the annotation of omap_device_build is wrong.
Signed-off-by: Tony Lindgren <tony@atomide.com>
During the migration to the common clock framework, calls to the
functions omap2xxx_clkt_vps_late_init() were not preserved for
OMAP2420 and OMAP2430. This causes the variables "sys_ck_rate" and
"curr_prcm_set" to be uninitialised on boot. On reboot, this causes the
following error message to be displayed because the appropriate MPU
clock frequency (derived from sys_ck_rate) cannot be found.
"Could not set MPU rate to 4294MHz"
Fix this by adding back calls to omap2xxx_clkt_vps_late_init() in the
OMAP2420 and OMAP2430 clock initialisation code.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: dropped the duplicated call to
omap2xxx_clkt_vps_check_bootloader_rates() after consultation with Jon;
updated patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
McPDM need to be configured to NO_IDLE mode when it is in used otherwise
vital clocks will be gated which results 'slow motion' audio playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[paul@pwsan.com: copy patch description into hwmod data comments]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
To avoid issues with audio caused by non locked ABE DPLL we should
make sure it is locked in all OMAP4 revisions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: cleaned up patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds basic DT bindings for OMAP GPMC.
The actual peripherals are instantiated from child nodes within the GPMC
node, and the only type of device that is currently supported is NAND.
Code was added to parse the generic GPMC timing parameters and some
documentation with examples on how to use them.
Successfully tested on an AM33xx board.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
[tony@atomide.com: updated to apply]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The am33xx is capable of handling bch error correction modes, so
enable that feature in the driver.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
gpmc_nand_init() will be called from another driver's probe() function,
so the easiest way to prevent section mismatches is to drop the
annotation here.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This creates irqchip initialization infrastructure from Thomas
Petazzoni. The VIC and GIC irqchip code is moved to drivers/irqchips
and adapted to use the new infrastructure. All DT enabled platforms
using GIC and VIC are converted over to use the new irqchip_init.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ8ZobAAoJEMhvYp4jgsXiihIH/2VvxmSHZb0e3jN6AR0B42b7
9EwX0IE0B23t91hNTwdzzmTJQYA7pMmWkgHNfd3vIeqSepJAmrVv/gp4iM9CtPwE
KNh+kDWOK2ZsOH4Vb0lYRJHN8WQOIQHuCUr9+MdYLNOgf/pPL6G/Y9kv9A1e7fTC
W+tFRjC5N1ilZMGyowX12L1wnwDk6kHzed6YV6bskC17cZ9/pg8PhSVbM4A/3kAv
NXYKqbXJb+eCsWGXg/knZXOL6V9gBwvVYoe4O9X3nQ0226AWB9caad8l8tchAjRB
fmrYF1tbkpOWPnLxhvQy5b5MJichJgTMJHh7RgiEcc/3f63kOljjlx4QKiqHvT0=
=q7gm
-----END PGP SIGNATURE-----
Merge tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux into next/cleanup
From Rob Herring:
Initial irqchip init infrastructure and GIC and VIC clean-ups
This creates irqchip initialization infrastructure from Thomas
Petazzoni. The VIC and GIC irqchip code is moved to drivers/irqchips
and adapted to use the new infrastructure. All DT enabled platforms
using GIC and VIC are converted over to use the new irqchip_init.
* tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux:
irqchip: Move ARM vic.h to include/linux/irqchip/arm-vic.h
ARM: picoxcell: use common irqchip_init function
ARM: spear: use common irqchip_init function
irqchip: Move ARM VIC to drivers/irqchip
ARM: samsung: remove unused tick.h
ARM: remove unneeded vic.h includes
ARM: remove mach .handle_irq for VIC users
ARM: VIC: set handle_arch_irq in VIC initialization
ARM: VIC: shrink down vic.h
irqchip: Move ARM gic.h to include/linux/irqchip/arm-gic.h
ARM: use common irqchip_init for GIC init
irqchip: Move ARM GIC to drivers/irqchip
ARM: remove mach .handle_irq for GIC users
ARM: GIC: set handle_arch_irq in GIC initialization
ARM: GIC: remove direct use of gic_raise_softirq
ARM: GIC: remove assembly ifdefs from gic.h
ARM: mach-ux500: use SGI0 to wake up the other core
arm: add set_handle_irq() to register the parent IRQ controller handler function
irqchip: add basic infrastructure
irqchip: add to the directories part of the IRQ subsystem in MAINTAINERS
Fixed up massive merge conflicts with the timer cleanup due to adjacent changes:
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-bcm/board_bcm.c
arch/arm/mach-cns3xxx/cns3420vb.c
arch/arm/mach-ep93xx/adssphere.c
arch/arm/mach-ep93xx/edb93xx.c
arch/arm/mach-ep93xx/gesbc9312.c
arch/arm/mach-ep93xx/micro9.c
arch/arm/mach-ep93xx/simone.c
arch/arm/mach-ep93xx/snappercl15.c
arch/arm/mach-ep93xx/ts72xx.c
arch/arm/mach-ep93xx/vision_ep9307.c
arch/arm/mach-highbank/highbank.c
arch/arm/mach-imx/mach-imx6q.c
arch/arm/mach-msm/board-dt-8960.c
arch/arm/mach-netx/nxdb500.c
arch/arm/mach-netx/nxdkn.c
arch/arm/mach-netx/nxeb500hmi.c
arch/arm/mach-nomadik/board-nhk8815.c
arch/arm/mach-picoxcell/common.c
arch/arm/mach-realview/realview_eb.c
arch/arm/mach-realview/realview_pb1176.c
arch/arm/mach-realview/realview_pb11mp.c
arch/arm/mach-realview/realview_pba8.c
arch/arm/mach-realview/realview_pbx.c
arch/arm/mach-socfpga/socfpga.c
arch/arm/mach-spear13xx/spear1310.c
arch/arm/mach-spear13xx/spear1340.c
arch/arm/mach-spear13xx/spear13xx.c
arch/arm/mach-spear3xx/spear300.c
arch/arm/mach-spear3xx/spear310.c
arch/arm/mach-spear3xx/spear320.c
arch/arm/mach-spear3xx/spear3xx.c
arch/arm/mach-spear6xx/spear6xx.c
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-u300/core.c
arch/arm/mach-ux500/board-mop500.c
arch/arm/mach-ux500/cpu-db8500.c
arch/arm/mach-versatile/versatile_ab.c
arch/arm/mach-versatile/versatile_dt.c
arch/arm/mach-versatile/versatile_pb.c
arch/arm/mach-vexpress/v2m.c
include/asm-generic/vmlinux.lds.h
Clockevent cleanup series from Shawn Guo.
Resolved move/change conflict in mach-pxa/time.c due to the sys_timer
cleanup.
* clocksource/cleanup:
clocksource: use clockevents_config_and_register() where possible
ARM: use clockevents_config_and_register() where possible
clockevents: export clockevents_config_and_register for module use
+ sync to Linux 3.8-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-pxa/time.c
The clockevent core is able to figure out the best mult and shift,
calculate min_delta_ns and max_delta_ns, with the necessary info passed
into clockevents_config_and_register(). Use this combined configure
and register function where possible to make the codes less error prone
and gain some positive diff stat.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Tested-by: Roland Stigge <stigge@antcom.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: David Brown <davidb@codeaurora.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Barry Song <baohua.song@csr.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
On DT driven boards, the gpmc node will match the driver. Hence, there's
no need to do that unconditionally from the initcall.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we have GIC moved to drivers/irqchip and all GIC DT init for
platforms using irqchip_init, move gic.h and update the remaining
includes.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Convert all GIC DT initialization over to use common irqchip_init
function.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Now that the GIC initialization sets up the handle_arch_irq pointer, we
can remove it for all machines and make it static.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
These are no longer needed, we now have to select the
debug_ll port manually. The new multiplatform version of the
debug_ll code is in arch/arm/include/debug/omap2plus.S.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Flip on multiplatform support for omap2+.
No changes to omap2plus_defconfig needed, but please note
that you may need to update your custom config files to
make sure you have:
CONFIG_ARCH_MULTIPLATFORM=y
CONFIG_ARCH_MULTI_V7=y
CONFIG_ARCH_OMAP2PLUS=y
And may need CONFIG_ARCH_MULTI_V6=y if booting omap2 boards.
Cc: Russell King <linux@arm.linux.org.uk>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We still need to fix up few places for multiplatform support,
but that can proceed separately. Fix the issue by making the
problem drivers depends !ARCH_MULTIPLATFORM for now.
The remaining pieces that are not multiplatform compatible
for omap2+ SoCs are:
1. Some drivers are using custom omap_dm_timer calls
There are two drivers that are directly usign omap hardware
timers for PWM and DSP clocking: drivers/media/rc/ir-rx51.c and
drivers/staging/tidspbridge/core/dsp-clock.c. These can be
fixed for multiplatform by allowing a minimal set of hardware
timers to be accessed, and for some functionality by using the
hrtimer framework.
2. Hardware OMAP4_ERRATA_I688 needs to be fixed up
This can't be enabled for multiplatform configurations in
it's current form. It may be possible to fix it up to do
instruction replacement early on during init. Luckily it
looks like this errata does not seem to get hit with
mainline kernel code alone at least currently.
3. Legacy header needed for omap-sham.c
Looks like it still needs mach/irqs.h for omap1 that
does not exist for multiplatform systems. Just ifdef
it for now.
4. Mailbox is waiting to get moved to drivers
Disable it for now to avoid adding a dependency to the
mailbox patches.
Cc: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: Sean Young <sean@mess.org>
Cc: "Víctor Manuel Jáquez Leal" <vjaquez@igalia.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
[tony@atomide.com: updated to disable mailbox]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise omap dmaengine will initialized when booted
on other SoCs. Fix this by initializing the platform
device in arch/arm/*omap*/dma.c instead.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We only want this initcall to run when the kernel is
booted on omap SoCs. Fix the issue by initializing the
the initcall from separately for omap1 and omap2+.
This fixes the issue for omap2+ multiplatform configs
as we are using omap_subsys_initcall there.
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way the initcalls don't run on other SoCs on multiplatform
kernels. Otherwise we'll get something like this when booting
on vexpress:
omap_hwmod: _ensure_mpu_hwmod_is_setup: MPU initiator hwmod mpu not yet registered
...
WARNING: at arch/arm/mach-omap2/pm.c:82 _init_omap_device+0x74/0x94()
_init_omap_device: could not find omap_hwmod for mpu
...
omap-dma-engine omap-dma-engine: OMAP DMA engine driver
...
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to make sure that multiplatform kernels don't
run omap initcalls when booted on other SoCs.
Do this by adding wrapper macros for the initcalls that
return early if soc_is_omap() test fails. This allows
us to easily change the defines later if we have SoC
specific init sections available.
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With ARCH_HAS_DECOMP_WDOG removed from arch/arm/boot/compressed/decompress.c,
all the arch_decomp_wdog() definition at platform level is unneeded.
Remmove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
In preparation of moving gic code to drivers/irqchip, remove the direct
platform dependencies on gic_raise_softirq. Move the setup of
smp_cross_call into the gic code and use arch_send_wakeup_ipi_mask
function to trigger wake-up IPIs.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
People are back from the holiday breaks, and it shows. Here are a bunch of
fixes for a number of platforms:
- A couple of small fixes for Nomadik
- A larger set of changes for kirkwood/mvebu
- uart driver selection, dt clocks, gpio-poweroff fixups,
a few __init annotation fixes and some error handling improvement
in their xor dma driver.
- i.MX had a couple of minor fixes (and a critical one for flexcan2
clock setup)
- MXS has a small board fix and a framebuffer bugfix
- A set of fixes for Samsung Exynos, fixing default bootargs and some
Exynos5440 clock issues
- A set of OMAP changes including PM fixes and a few sparse warning
fixups
All in all a bit more positive code delta than we'd ideally want to see
here, mostly from the OMAP PM changes, but nothing overly crazy.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s9fE
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"People are back from the holiday breaks, and it shows. Here are a
bunch of fixes for a number of platforms:
- A couple of small fixes for Nomadik
- A larger set of changes for kirkwood/mvebu
- uart driver selection, dt clocks, gpio-poweroff fixups, a few
__init annotation fixes and some error handling improvement in
their xor dma driver.
- i.MX had a couple of minor fixes (and a critical one for flexcan2
clock setup)
- MXS has a small board fix and a framebuffer bugfix
- A set of fixes for Samsung Exynos, fixing default bootargs and some
Exynos5440 clock issues
- A set of OMAP changes including PM fixes and a few sparse warning
fixups
All in all a bit more positive code delta than we'd ideally want to
see here, mostly from the OMAP PM changes, but nothing overly crazy."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
pinctrl: mvebu: make pdma clock on dove mandatory
ARM: Dove: Add pinctrl clock to DT
dma: mv_xor: fix error handling for clocks
dma: mv_xor: fix error handling of mv_xor_channel_add()
arm: mvebu: Add missing ; for cpu node.
arm: mvebu: Armada XP MV78230 has only three Ethernet interfaces
arm: mvebu: Armada XP MV78230 has two cores, not one
clk: mvebu: Remove inappropriate __init tagging
ARM: Kirkwood: Use fixed-regulator instead of board gpio call
ARM: Kirkwood: Fix missing sdio clock
ARM: Kirkwood: Switch TWSI1 of 88f6282 to DT clock providers
...
This branch contains a number of cleanups and unifications to various
timer- clock-events- and ARM timer code. The main points are:
1) Convert arch_gettimeoffset to a pointer, so that architectures with
multiple timer implementations can simply set this standard pointer
rather than maintaining their own arch-specific pointers for the
same purpose. Various architectures are converted to using this new
feature.
2) Conversion of ARM timer implementations to use clock_event_devices's
suspend/resume operations, rather than the ARM-specific sys_timer
versions. Thus, the ARM code begins to use more common infra-structure
rather than arch-specific code.
3) Removal of ARM's struct sys_timer completely, now that everything uses
common code.
4) Introduction of drivers/clocksource/clksrc-of.c, which allows ARM clock
source implementations to be moved into drivers/clocksource, with the
need to add SoC-specific header files for each timer initialization
function; instead, all enabled implementations are registered into a
table which a single core function iterates over, and calls the
relevant initialization functions based on device tree. At least the
Tegra and BCM2835 clocksource implementations will use this feature in
the 3.9 kernel cycle.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=DOD6
-----END PGP SIGNATURE-----
Merge tag 'swarren-for-3.9-arm-timer-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
From Stephen Warren:
ARM/...: timer and clock events cleanup, and remove struct sys_timer
This branch contains a number of cleanups and unifications to various
timer- clock-events- and ARM timer code. The main points are:
1) Convert arch_gettimeoffset to a pointer, so that architectures with
multiple timer implementations can simply set this standard pointer
rather than maintaining their own arch-specific pointers for the
same purpose. Various architectures are converted to using this new
feature.
2) Conversion of ARM timer implementations to use clock_event_devices's
suspend/resume operations, rather than the ARM-specific sys_timer
versions. Thus, the ARM code begins to use more common infra-structure
rather than arch-specific code.
3) Removal of ARM's struct sys_timer completely, now that everything uses
common code.
4) Introduction of drivers/clocksource/clksrc-of.c, which allows ARM clock
source implementations to be moved into drivers/clocksource, with the
need to add SoC-specific header files for each timer initialization
function; instead, all enabled implementations are registered into a
table which a single core function iterates over, and calls the
relevant initialization functions based on device tree. At least the
Tegra and BCM2835 clocksource implementations will use this feature in
the 3.9 kernel cycle.
* tag 'swarren-for-3.9-arm-timer-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
clocksource: add common of_clksrc_init() function
ARM: delete struct sys_timer
ARM: remove struct sys_timer suspend and resume fields
ARM: samsung: register syscore_ops for timer resume directly
ARM: ux500: convert timer suspend/resume to clock_event_device
ARM: sa1100: convert timer suspend/resume to clock_event_device
ARM: pxa: convert timer suspend/resume to clock_event_device
ARM: at91: convert timer suspend/resume to clock_event_device
ARM: set arch_gettimeoffset directly
m68k: set arch_gettimeoffset directly
time: convert arch_gettimeoffset to a pointer
cris: move usec/nsec conversion to do_slow_gettimeoffset
Signed-off-by: Olof Johansson <olof@lixom.net>
The IRQ array must be terminated by -1 and not by -1+OMAP_INTC_START
This led to having a resource list of 100s of IRQs.
Looks like this was caused by commit a2cfc509 (ARM: OMAP3+: hwmod: Add
AM33XX HWMOD data) that probably had some search and replace updates
done for the patch for sparse irq support.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated wit information about the breaking commit]
Signed-off-by: Tony Lindgren <tony@atomide.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
logs are available here:
http://www.pwsan.com/omap/testlogs/prcm_fixes_b_3.8-rc/20130102120724/
The 3730 Beagle XM here has an intermittent failure mounting SD root,
but the suspicion right now is that this is due to a failing SD card,
rather than any change introduced by these patches.
This second version includes a few changes requested by Tony Lindgren.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQ5IkPAAoJEMePsQ0LvSpL/RQQAJUbGPZTdMEH2DHHDVPRxgBE
bWEg0RQfzheOLfFvfot2tReJoN7GMlhzcDq2DSHZLwp5b9XgOgOJdNdldvrvFljD
p3QEy+y/7ZSgsAdgDV33vAAUAv4c0CIh0cKgw3JwOn/dqVSbiMXXqXe1kZe419gi
bbJHBr6fZH63qvGzkjI17vl3lDq6RsX7vgtEQ9TeiTMUAOnrXzp3rt9oDNVsChSs
Ml6h1WKnxQdMFjbNNmBOUGltSg7O1rwuWeS/9mg77yV3lIZ5QdmAVlcq6lUB+jqy
CWhAYbrhXMBPYFaxzw0I8h00m0VNBSOZf2e1d5Lw8wU8dVxQ3PVZCI4SyRssBdd3
T+91zy4Axmo+SWrkTxpq+yE2Sn1AMZC4mJwI62UhCZV8TPPvek8IlK3ktKeV97ql
BNehuGYqbc3u5TiIjO8K+akTBKKTVDdXaah9ms8rtQ4hcwLwC0VA/71R9qaQJx3E
mGf3pRK6FSV83vEMrGb2mRk3ByGHzpYlMD0sb4+0OFvkj5Hyv7OCPb0TJapn6OPO
vpeG6pIbHN3p/mKrj/RNHVtvpV5/mHJmMOXgkcXLcdlZhsnGE21dqw/vPrvjf3Wa
SnUp7q48/4a2FP2d0KpQ+CpHyLyNEs4x4zs9hfjHGsYs1fWBwdu0+/8rVPaAEjjB
iUa8sxlv/1o0rJfiyRkd
=oUTN
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-a2-for-v3.8-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.8-rc2/fixes
Some OMAP PRCM and sparse fixes against v3.8-rc1. A basic set of test
logs are available here:
http://www.pwsan.com/omap/testlogs/prcm_fixes_b_3.8-rc/20130102120724/
The 3730 Beagle XM here has an intermittent failure mounting SD root,
but the suspicion right now is that this is due to a failing SD card,
rather than any change introduced by these patches.
This second version includes a few changes requested by Tony Lindgren.
On OMAP2xxx chips, the register bitfields for the
PM_PWSTCTRL_*.POWERSTATE and PM_PWSTST_*.LASTSTATEENTERED are
different than those used on OMAP3/4. The order is reversed. So, for
example, on OMAP2xxx, 0x0 indicates 'ON'; but on OMAP3/4, 0x0
indicates 'OFF'. Similarly, on OMAP2xxx, 0x3 indicates 'OFF', but on
OMAP3/4, 0x3 indicates 'ON'.
To fix this, we treat the OMAP3/4 values as the powerdomain API
values, and create new low-level powerdomain functions for the
OMAP2xxx chips which translate between the OMAP2xxx values and the
OMAP3/4 values.
Without this patch, the conversion of the OMAP2xxx PM code to the
functional powerstate code results in a non-booting kernel.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The ETM/ETB drivers for OMAP3, enable the emu_src_ck clock in order
to access the ETM/ETB hardware. The emu_src_ck should enable the EMU
clock domain so that the ETM/ETB hardware is accessible. However,
currently when enabling the emu_src_ck the EMU clock domain is not
being enabled and so the ETM/ETB drivers are failing. Add enable/disable
clock functions to enable the EMU clock domain when enabling the
emu_src_ck.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
To read reset sources registers we have to use PRM_DEVICE_INST
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
RSTTIME is offset 0x8 and RSTST is offset 0x04 for OMAP4430 and
OMAP4460.
Signed-off-by: Nishanth Menon <nm@ti.com>
[ivan.khoronzhuk@ti.com: ported from k3.4]
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In the map for reset sources register we use defines intended for
using with PRM_RSTCTRL register. So fix it.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 70384a6af0 ("ARM: OMAP3+:
hwmod: Add AM33XX HWMOD data for davinci_mdio module") adds two
new sparse warnings:
arch/arm/mach-omap2/omap_hwmod_33xx_data.c:2518:30: warning: symbol 'am33xx_mdio_addr_space' was not declared. Should it be static?
arch/arm/mach-omap2/omap_hwmod_33xx_data.c:2526:26: warning: symbol 'am33xx_cpgmac0__mdio' was not declared. Should it be static?
Fix by marking the two new records as static.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
From Tony Lindgren:
Here are few more patches to finish the omap changes for
multiplatform conversion that are not strictly fixes, but
were too complex to do with the dependencies during the
merge window. Those are to move of serial-omap.h to
platform_data, and the removal of remaining cpu_is_omap
macro usage outside mach-omap2.
Then there are several trivial fixes for typos and few
minimal omap2plus_defconfig updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=RE6Z
-----END PGP SIGNATURE-----
Merge tag 'omap-late-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM cleanups for omap from Olof Johansson:
"From Tony Lindgren:
Here are few more patches to finish the omap changes for multiplatform
conversion that are not strictly fixes, but were too complex to do
with the dependencies during the merge window. Those are to move of
serial-omap.h to platform_data, and the removal of remaining
cpu_is_omap macro usage outside mach-omap2.
Then there are several trivial fixes for typos and few minimal
omap2plus_defconfig updates."
* tag 'omap-late-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arch/arm/mach-omap2/dpll3xxx.c: drop if around WARN_ON
OMAP2: Fix a typo - replace regist with register.
ARM/omap: use module_platform_driver macro
ARM: OMAP2+: PMU: Remove unused header
ARM: OMAP4: remove duplicated include from omap_hwmod_44xx_data.c
ARM: OMAP2+: omap2plus_defconfig: enable twl4030 SoC audio
ARM: OMAP2+: omap2plus_defconfig: Add tps65217 support
ARM: OMAP2+: enable devtmpfs and devtmpfs automount
ARM: OMAP2+: omap_twl: Change TWL4030_MODULE_PM_RECEIVER to TWL_MODULE_PM_RECEIVER
ARM: OMAP2+: Drop plat/cpu.h for omap2plus
ARM: OMAP: Split fb.c to remove last remaining cpu_is_omap usage
MAINTAINERS: Add an entry for omap related .dts files
Now that the only field in struct sys_timer is .init, delete the struct,
and replace the machine descriptor .timer field with the initialization
function itself.
This will enable moving timer drivers into drivers/clocksource without
having to place a public prototype of each struct sys_timer object into
include/linux; the intent is to create a single of_clocksource_init()
function that determines which timer driver to initialize by scanning
the device dtree, much like the proposed irqchip_init() at:
http://www.spinics.net/lists/arm-kernel/msg203686.html
Includes mach-omap2 fixes from Igor Grinberg.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Here are a few more fixes for 3.8. Two branches of fixes for Samsung
platforms, including fixes for the audio build errors on all non-DT
platforms. There's also a fixup to the sunxi device-tree file renames
due to a bad patch application by me, and a fix for OMAP due to function
renames merged through the powerpc tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s7qv
-----END PGP SIGNATURE-----
Merge tag 'fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes part 2 from Olof Johansson:
"Here are a few more fixes for 3.8. Two branches of fixes for Samsung
platforms, including fixes for the audio build errors on all non-DT
platforms. There's also a fixup to the sunxi device-tree file renames
due to a bad patch application by me, and a fix for OMAP due to
function renames merged through the powerpc tree."
* tag 'fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP2+: Fix compillation error in mach-omap2/timer.c
ARM: sunxi: rename device tree source files
ARM: EXYNOS: Avoid passing the clks through platform data
ARM: S5PV210: Avoid passing the clks through platform data
ARM: S5P64X0: Add I2S clkdev support
ARM: S5PC100: Add I2S clkdev support
ARM: S3C64XX: Add I2S clkdev support
ARM: EXYNOS: Fix MSHC clocks instance names
ARM: EXYNOS: Fix NULL pointer dereference bug in SMDKV310
ARM: EXYNOS: Fix NULL pointer dereference bug in SMDK4X12
ARM: EXYNOS: Fix NULL pointer dereference bug in Origen
ARM: SAMSUNG: Add missing include guard to gpio-core.h
pinctrl: exynos5440/samsung: Staticize pcfgs
pinctrl: samsung: Fix a typo in pinctrl-samsung.h
ARM: EXYNOS: fix skip scu_enable() for EXYNOS5440
ARM: EXYNOS: fix GIC using for EXYNOS5440
ARM: EXYNOS: fix build error when MFC is not selected
Commit 787314c35f ("Merge tag 'iommu-updates-v3.8' of
git://git./linux/kernel/git/joro/iommu") did not account for the changed
header location.
The headers were made local to mach-omap2 as they are specific to omap2+
only, and we wanted to get most of the #include <plat/*.h> headers fixed
up anyways for the ARM multiplatform support.
We attempted to avoid this kind of merge conflict early on by setting up
a minimal git branch shared by the arm-soc tree and the iommu tree, but
looks like we still hit a merge issue there as the branches got merged
as various topic branches.
Cc: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A few new features this merge-window. The most important one is
probably, that dma-debug now warns if a dma-handle is not checked with
dma_mapping_error by the device driver. This requires minor changes to
some architectures which make use of dma-debug. Most of these changes
have the respective Acks by the Arch-Maintainers.
Besides that there are updates to the AMD IOMMU driver for refactor the
IOMMU-Groups support and to make sure it does not trigger a hardware
erratum.
The OMAP changes (for which I pulled in a branch from Tony Lindgren's
tree) have a conflict in linux-next with the arm-soc tree. The conflict
is in the file arch/arm/mach-omap2/clock44xx_data.c which is deleted in
the arm-soc tree. It is safe to delete the file too so solve the
conflict. Similar changes are done in the arm-soc tree in the common
clock framework migration. A missing hunk from the patch in the IOMMU
tree will be submitted as a seperate patch when the merge-window is
closed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pPHZ
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"A few new features this merge-window. The most important one is
probably, that dma-debug now warns if a dma-handle is not checked with
dma_mapping_error by the device driver. This requires minor changes
to some architectures which make use of dma-debug. Most of these
changes have the respective Acks by the Arch-Maintainers.
Besides that there are updates to the AMD IOMMU driver for refactor
the IOMMU-Groups support and to make sure it does not trigger a
hardware erratum.
The OMAP changes (for which I pulled in a branch from Tony Lindgren's
tree) have a conflict in linux-next with the arm-soc tree. The
conflict is in the file arch/arm/mach-omap2/clock44xx_data.c which is
deleted in the arm-soc tree. It is safe to delete the file too so
solve the conflict. Similar changes are done in the arm-soc tree in
the common clock framework migration. A missing hunk from the patch
in the IOMMU tree will be submitted as a seperate patch when the
merge-window is closed."
* tag 'iommu-updates-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (29 commits)
ARM: dma-mapping: support debug_dma_mapping_error
ARM: OMAP4: hwmod data: ipu and dsp to use parent clocks instead of leaf clocks
iommu/omap: Adapt to runtime pm
iommu/omap: Migrate to hwmod framework
iommu/omap: Keep mmu enabled when requested
iommu/omap: Remove redundant clock handling on ISR
iommu/amd: Remove obsolete comment
iommu/amd: Don't use 512GB pages
iommu/tegra: smmu: Move bus_set_iommu after probe for multi arch
iommu/tegra: gart: Move bus_set_iommu after probe for multi arch
iommu/tegra: smmu: Remove unnecessary PTC/TLB flush all
tile: dma_debug: add debug_dma_mapping_error support
sh: dma_debug: add debug_dma_mapping_error support
powerpc: dma_debug: add debug_dma_mapping_error support
mips: dma_debug: add debug_dma_mapping_error support
microblaze: dma-mapping: support debug_dma_mapping_error
ia64: dma_debug: add debug_dma_mapping_error support
c6x: dma_debug: add debug_dma_mapping_error support
ARM64: dma_debug: add debug_dma_mapping_error support
intel-iommu: Prevent devices with RMRRs from being placed into SI Domain
...
prom_add_property() has been renamed to of_add_property()
This patch fixes the following comilation error:
arch/arm/mach-omap2/timer.c: In function ‘omap_get_timer_dt’:
arch/arm/mach-omap2/timer.c:178:3: error: implicit declaration of function ‘prom_add_property’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[1]: *** [arch/arm/mach-omap2/timer.o] Error 1
make[1]: *** Waiting for unfinished jobs....
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge commit 752451f01c ("Merge branch 'i2c-embedded/for-next' of
git://git.pengutronix.de/git/wsa/linux") resulted in a build breakage
for OMAP
arch/arm/mach-omap2/i2c.c: In function 'omap_pm_set_max_mpu_wakeup_lat_compat':
arch/arm/mach-omap2/i2c.c:130:2: error: implicit declaration of function 'omap_pm_set_max_mpu_wakeup_lat'
make[1]: *** [arch/arm/mach-omap2/i2c.o] Error 1
Fix this by including the appropriate header file with the function
prototype.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a batch of fixes for arm-soc platforms, most of it is for OMAP
but there are others too (i.MX, Tegra, ep93xx). Fixes warnings, some
broken platforms and drivers, etc. A bit all over the map really.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4g/i
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is a batch of fixes for arm-soc platforms, most of it is for OMAP
but there are others too (i.MX, Tegra, ep93xx). Fixes warnings, some
broken platforms and drivers, etc. A bit all over the map really."
There was some concern about commit 68136b10 ("RM: sunxi: Change device
tree naming scheme for sunxi"), but Tony says:
"Looks like that's trivial to fix as needed, no need to rebuild the
branch to fix that AFAIK.
The fix can be done once Olof is available online again.
Linus, I suggest that you go ahead and pull this if there are no other
issues with this branch."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
ARM: sunxi: Change device tree naming scheme for sunxi
ARM: ux500: fix missing include
ARM: u300: delete custom pin hog code
ARM: davinci: fix build break due to missing include
ARM: exynos: Fix warning due to missing 'inline' in stub
ARM: imx: Move platform-mx2-emma to arch/arm/mach-imx/devices
ARM i.MX51 clock: Fix regression since enabling MIPI/HSP clocks
ARM: dts: mx27: Fix the AIPI bus for FEC
ARM: OMAP2+: common: remove use of vram
ARM: OMAP3/4: cpuidle: fix sparse and checkpatch warnings
ARM: OMAP4: clock data: DPLLs are missing bypass clocks in their parent lists
ARM: OMAP4: clock data: div_iva_hs_clk is a power-of-two divider
ARM: OMAP4: Fix EMU clock domain always on
ARM: OMAP4460: Workaround ABE DPLL failing to turn-on
ARM: OMAP4: Enhance support for DPLLs with 4X multiplier
ARM: OMAP4: Add function table for non-M4X dplls
ARM: OMAP4: Update timer clock aliases
ARM: OMAP: Move plat/omap-serial.h to include/linux/platform_data/serial-omap.h
ARM: dts: Add build target for omap4-panda-a4
ARM: dts: OMAP2420: Correct H4 board memory size
...
- A small patch for the RX51 OMAP board (Nokia N900 phone), the patch
creates a battery monitor device instance, so that it can be probed. It
was acked by the OMAP maintainer;
- A couple of late bug fixes for the charger-manager: corrects corner
cases for the battery full handling.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=hppb
-----END PGP SIGNATURE-----
Merge tag 'for-v3.8-part2' of git://git.infradead.org/battery-2.6
Pull battery update, part 2, from Anton Vorontsov:
"These are left overs that I didn't have time to review/apply before
the merge window opened. I didn't want to "spoil" the first pull
request with these late patches, so they were not included:
- A small patch for the RX51 OMAP board (Nokia N900 phone), the patch
creates a battery monitor device instance, so that it can be
probed. It was acked by the OMAP maintainer;
- A couple of late bug fixes for the charger-manager: corrects corner
cases for the battery full handling."
* tag 'for-v3.8-part2' of git://git.infradead.org/battery-2.6:
charger-manager: Fix bug when check dropped voltage after fullbatt event
charger-manager: Fix bug related to checking fully charged state of battery
ARM: OMAP: rx51: Register platform device for rx51_battery
Pull i2c-embedded changes from Wolfram Sang:
- CBUS driver (an I2C variant)
- continued rework of the omap driver
- s3c2410 gets lots of fixes and gains pinctrl support
- at91 gains DMA support
- the GPIO muxer gains devicetree probing
- typical fixes and additions all over
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (45 commits)
i2c: omap: Remove the OMAP_I2C_FLAG_RESET_REGS_POSTIDLE flag
i2c: at91: add dma support
i2c: at91: change struct members indentation
i2c: at91: fix compilation warning
i2c: mxs: Do not disable the I2C SMBus quick mode
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Remove recently introduced performance overheads
i2c: ocores: Move grlib set/get functions into #ifdef CONFIG_OF block
i2c: s3c2410: Add fix for i2c suspend/resume
i2c: s3c2410: Fix code to free gpios
i2c: i2c-cbus-gpio: introduce driver
i2c: ocores: Add support for the GRLIB port of the controller and use function pointers for getreg and setreg functions
i2c: ocores: Add irq support for sparc
i2c: omap: Move the remove constraint
ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049
i2c: s3c2410: do not special case HDMIPHY stuck bus detection
i2c: s3c2410: use exponential back off while polling for bus idle
i2c: s3c2410: do not generate STOP for QUIRK_HDMIPHY
i2c: s3c2410: grab adapter lock while changing i2c clock
i2c: s3c2410: Add support for pinctrl
...
conflict with the fb code, few timer warnings, and longer
term regressions for tfp410 and omap h4 ethernet. Also
included is a GPIO mode fix for the legacy mux code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=8+P4
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/fixes-for-merge-window-v4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
These patches fixes a build error caused by a merge
conflict with the fb code, few timer warnings, and longer
term regressions for tfp410 and omap h4 ethernet. Also
included is a GPIO mode fix for the legacy mux code.
* tag 'omap-for-v3.8/fixes-for-merge-window-v4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: common: remove use of vram
ARM: OMAP: Move plat/omap-serial.h to include/linux/platform_data/serial-omap.h
ARM: dts: Add build target for omap4-panda-a4
ARM: dts: OMAP2420: Correct H4 board memory size
mfd: omap-usb-host: get rid of cpu_is_omap..() macros
ARM: OMAP: Remove debug-devices.c
ARM: OMAP2420: Fix ethernet support for OMAP2420 H4
OMAP2+: mux: Fixed gpio mux mode analysis
OMAP: board-files: fix i2c_bus for tfp410
ARM: OMAP2+: Fix sparse warnings in timer.c
ARM: AM335x: Fix warning in timer.c
ARM: OMAP2+: Fix realtime_counter_init warning in timer.c
the OMAP CPUIdle code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=RfYH
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-a-for-v3.8-window' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
From Paul Walmsley per Tony Lindgrens request:
Fix some OMAP4 clock problems, and deal with some sparse warnings from
the OMAP CPUIdle code.
* tag 'omap-fixes-a-for-v3.8-window' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP3/4: cpuidle: fix sparse and checkpatch warnings
ARM: OMAP4: clock data: DPLLs are missing bypass clocks in their parent lists
ARM: OMAP4: clock data: div_iva_hs_clk is a power-of-two divider
ARM: OMAP4: Fix EMU clock domain always on
ARM: OMAP4460: Workaround ABE DPLL failing to turn-on
ARM: OMAP4: Enhance support for DPLLs with 4X multiplier
ARM: OMAP4: Add function table for non-M4X dplls
ARM: OMAP4: Update timer clock aliases
Just use WARN_ON rather than an if containing only WARN_ON(1).
A simplified version of the semantic patch that makes this transformation
is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
- if (e) WARN_ON(1);
+ WARN_ON(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 2ac29a1 (ARM: PMU: fix runtime PM enable) moved the call to
pm_runtime_enable() from the OMAP2+ PMU code into the ARM PERF core
code. However, header for pm_runtime which should have been removed
from the OMAP2+ PMU code was not. It is no longer necessary to include
this header in the OMAP2+ PMU code and so remove it.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
To facilitate upcoming cleanup in twl stack.
No functional change.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The cpu_is_omap macros are now local to arch/arm/mach-omap2
in soc.h and plat/cpu.h can finally be dropped for omap2+.
Thanks everybody for help with fixing the drivers.
Note that we can now also remove the unused plat/cpu.h from
smartreflex.c and isp.c as they will cause compile errors
with ARCH_MULTIPLATFORM enabled.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Jean Pihet <jean.pihet@newoldbits.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we missed plat-omap/fb.c for cpu_is_omap usage
mach-omap2. This is the last user of cpu_is_omap, so let's
quickly fix it up so we can finally remove plat/cpu.h for
omap2lus.
We want to limit cpu_is_omap macro usage to mach-omap2 only so
we can make plat/cpu.h private. After this we can finally drop
plat/cpu.h for omap2+.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is needed to make the battery monitor actually work on Nokia N900.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
commit 966458f OMAP: remove vram allocator
Removed the OMAP specific vram allocator but OMAP2 common was
still trying to use it and this lead to the following build error:
CC arch/arm/mach-omap2/common.o
arch/arm/mach-omap2/common.c:19:23: fatal error: plat/vram.h: No such file or directory
compilation terminated.
make[1]: *** [arch/arm/mach-omap2/common.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAPDSS changes, including:
- use dynanic debug prints
- OMAP platform dependency removals
- Creation of compat-layer, helping us to improve omapdrm
- Misc cleanups, aiming to make omadss more in line with the upcoming common
display framework
Exynos DP changes for the 3.8 merge window:
- Device Tree support for Samsung Exynos DP
- SW Link training is cleaned up.
- HPD interrupt is supported.
Samsung Framebuffer changes for the 3.8 merge window:
- The bit definitions of header file are updated.
- Some minor typos are fixed.
- Some minor bugs of s3c_fb_check_var() are fixed.
FB related changes for SH Mobile, Freescale DIU
Add support for the Solomon SSD1307 OLED Controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=KVPX
-----END PGP SIGNATURE-----
Merge tag 'fbdev-for-3.8' of git://gitorious.org/linux-omap-dss2/linux
Pull fbdev changes from Tomi Valkeinen:
"OMAPDSS changes, including:
- use dynanic debug prints
- OMAP platform dependency removals
- Creation of compat-layer, helping us to improve omapdrm
- Misc cleanups, aiming to make omadss more in line with the upcoming
common display framework
Exynos DP changes for the 3.8 merge window:
- Device Tree support for Samsung Exynos DP
- SW Link training is cleaned up.
- HPD interrupt is supported.
Samsung Framebuffer changes for the 3.8 merge window:
- The bit definitions of header file are updated.
- Some minor typos are fixed.
- Some minor bugs of s3c_fb_check_var() are fixed.
FB related changes for SH Mobile, Freescale DIU
Add support for the Solomon SSD1307 OLED Controller"
* tag 'fbdev-for-3.8' of git://gitorious.org/linux-omap-dss2/linux: (191 commits)
OMAPDSS: fix TV-out issue with DSI PLL
Revert "OMAPFB: simplify locking"
OMAPFB: remove silly loop in fb2display()
OMAPFB: fix error handling in omapfb_find_best_mode()
OMAPFB: use devm_kzalloc to allocate omapfb2_device
OMAPDSS: DISPC: remove dispc fck uses
OMAPDSS: DISPC: get dss clock rate from dss driver
drivers/video/console/softcursor.c: remove redundant NULL check before kfree()
drivers/video: add support for the Solomon SSD1307 OLED Controller
OMAPDSS: use omapdss_compat_init() in other drivers
OMAPDSS: export dispc functions
OMAPDSS: export dss_feat functions
OMAPDSS: export dss_mgr_ops functions
OMAPDSS: separate compat files in the Makefile
OMAPDSS: move display sysfs init to compat layer
OMAPDSS: DPI: use dispc's check_timings
OMAPDSS: DISPC: add dispc_ovl_check()
OMAPDSS: move irq handling to dispc-compat
OMAPDSS: move omap_dispc_wait_for_irq_interruptible_timeout to dispc-compat.c
OMAPDSS: move blocking mgr enable/disable to compat layer
...
Conflicts:
arch/arm/mach-davinci/devices-da8xx.c
arch/arm/plat-omap/common.c
drivers/media/platform/omap/omap_vout.c
Fix the following sparse warnings in the OMAP3/4 CPUIdle code:
arch/arm/mach-omap2/cpuidle34xx.c:272:1: warning: symbol 'omap3_idle_dev' was not declared. Should it be static?
arch/arm/mach-omap2/cpuidle34xx.c:274:23: warning: symbol 'omap3_idle_driver' was not declared. Should it be static?
arch/arm/mach-omap2/cpuidle44xx.c:164:1: warning: symbol 'omap4_idle_dev' was not declared. Should it be static?
arch/arm/mach-omap2/cpuidle44xx.c:166:23: warning: symbol 'omap4_idle_driver' was not declared. Should it be static?
Also fix the following checkpatch warnings:
WARNING: please, no space before tabs
#44: FILE: arch/arm/mach-omap2/cpuidle34xx.c:105:
+^I.name = ^I"omap3_idle",$
WARNING: please, no space before tabs
#45: FILE: arch/arm/mach-omap2/cpuidle34xx.c:106:
+^I.owner = ^ITHIS_MODULE,$
ERROR: code indent should use tabs where possible
#211: FILE: arch/arm/mach-omap2/cpuidle44xx.c:74:
+ /* C2 - CPU0 OFF + CPU1 OFF + MPU CSWR */$
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Booting OMAP4460 Pandaboard ES with a recent u-boot results in this
warning:
WARNING: at arch/arm/mach-omap2/dpll3xxx.c:427 omap3_noncore_dpll_enable+0xf4/0x110()
The OMAP4 DPLL parent clock names only listed the reference clocks,
not the bypass clocks. Fix by adding the bypass clocks to the DPLL
parent lists.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@linaro.org>
The OMAP4 clock divider "div_iva_hs_clk" is listed in the clock data
as an OMAP HSDIVIDER, but it's actually a power-of-two divider. This
causes a warning during boot on an OMAP4460 Pandaboard-ES with a
recent u-boot:
WARNING: at arch/arm/mach-omap2/clkt_clksel.c:143 omap2_clksel_recalc+0xf4/0x12c()
clock: div_iva_hs_clk: could not find fieldval 0 for parent dpll_core_m5x2_ck
Fix by converting the data for this clock to a power-of-two divider.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@linaro.org>
Commit d043d87 (ARM: OMAP2+: clockdomain: bypass clockdomain handling
when disabling unused clks) skips the decrementing of a clock-domains
use count if the clocks use count is zero. However, for OMAP4 devices
this is causing the EMU clock-domain to be stuck ON as the use count is
not getting decremented correctly.
The scenario that leads to this problem is described below ...
omap_hwmod_setup_all
--> _setup
--> clkdm_hwmod_enable
--> EMU clock domain usecount = 1
--> _enable_clocks
--> clk_enable
--> trace_clk_div_div usecount = 1
--> clkdm_hwmod_enable
--> EMU clock domain usecount = 2
--> _idle
--> _disable_clocks
--> clk_disable
--> trace_clk_div_div usecount = 0
--> clkdm_hwmod_disable
--> skips decrement of EMU clock domain usecount
because trace_clk_div_div is 0!
--> EMU clock domain usecount = 2
--> clkdm_hwmod_disable
--> EMU clock domain usecount = 1
Hence, due to the order that a clocks use count is decremented and the
clock domain is disabled, it is possible that the clock domain can have
a non-zero use count when the actual clock has a use count of 0.
Therefore, we should only bypass the clock-domain handling when both the
clock-domain and clock in the clock-domain have a use count of 0 and
warn when the clock-domain has a zero use count and the clock has a
non-zero use count.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: fixed checkpatch warning]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
With the latest mainline u-boot bootloader (v2012.10), timers (5-8) in
the ABE power domain are failing to turn-on. The timers never come out
of the disabled state when setting the module-mode field to enable.
The problem was exposed when u-boot was updated to NOT configure and
lock the ABE DPLL on start-up. If the ABE DPLL is configured and locked
by u-boot the problem does not occur. However, if the ABE DPLL is in the
idle low-power bypass state and we attempt to enable a timer in the ABE
power domain, it remains stuck in the disabled state. It appears to be a
problem the timer interface clock as this comes from the ABE DPLL.
If we place the ABE DPLL in the MN-bypass state and not the idle
low-power state, then this problem is not seen.
This problem only appears to occur on OMAP4460 and not OMAP4430.
Workaround this problem by locking the ABE DPLL for OMAP4460 in the
kernel on boot. By locking the ABE DPLL, when clocks from the ABE DPLL
are not being requested the DPLL will transition into a low-power stop
mode.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4 devices, the ABE DPLL has an internal 4X multiplier that can
be enabled or disabled in addition to the standard configurable
multiplier (M) for OMAP DPLLs. When configuring the ABE DPLL the 4X
multiplier is accounted for by checking to see whether it is enabled or
not. However, when calculating a new rate we only check to see if the
rate can be achieved with the current setting for the 4X multiplier.
Enhance the round_rate() function for such DPLLs to see if the rate
can be achieved with the 4X multiplier if it cannot be achieved without
the 4X multiplier.
This change is necessary, because when using the 32kHz clock as the
source clock for the ABE DPLL, the default DPLL frequency for the ABE
DPLL cannot be achieved without enabling the 4X multiplier.
When using the 32kHz clock as the source clock for the ABE DPLL and
attempting to lock the DPLL to 98.304MHz (default frequency), it was
found that the DPLL would fail to lock if the low-power mode for the DPLL
was not enabled. From reviewing boot-loader settings that configure the
ABE DPLL it was found that the low-power mode is enabled when using the
32kHz clock source, however, the documentation for OMAP does not state
that this is a requirement. Therefore, introduce a new function for
OMAP4 devices to see if low-power mode can be enabled when calculating a
new rate to ensure the DPLL will lock.
New variables for the last calculated 4X multiplier and low-power
setting have been added to the dpll data structure as well as variables
defining the bit mask for enabling these features via the DPLL's
control_reg. It is possible that we could eliminate these bit masks from
the dpll data structure as these bit masks are not unique to OMAP4, if
it is preferred.
The function omap3_noncore_program_dpll() has been updated to avoid
passing the calculated values for the multiplier (M) and divider (N) as
these are stored in the clk structure.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently all OMAP4 non-core DPLLs use the same function table for
configuring DPLLs. For these DPLLs, the function
omap4_dpll_regm4xen_recalc() is used to recalculate the DPLL rate and
the function omap4_dpll_regm4xen_round_rate() is used to calculate the
closest rate to that requested. However, these omap4_dpll_regm4xen_xxx()
functions are only applicable to the ABE DPLL and not the other non-core
DPLLs. Therefore, add a new function table for non-core DPLLs that do
not include the 4X-multiplier (M4X).
Please note that using these omap4_dpll_regm4x_xxx() function works for
the non-M4X DPLLs today because we only check to see if the 4X
multiplier is enabled when calculating the rate. However, it is planned
that the dpll functions will be enhanced to enable the 4X multiplier as
necessary (in order to achieve the requested rate) and so calling these
functions for non-M4X dplls will no longer work.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit "ARM: dts: OMAP4: Update timer addresses" updated the device-tree
names of the OMAP4 timers 5-7 because the default address for the timers
was changed from the L3 address to the MPU private address. When booting
with device-tree, this introduces a regression when attempting to set
the parent clock of timers 5-7 to the sys_clk_div_ck. Therefore, update
the clock aliases for timer 5-7 to reflect the updated device-tree name
for the timers.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: updated to apply after the CCF conversion]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
We need to move this file to allow ARM multiplatform configurations
to build for omap2+. This can now be done as this file now only
contains platform_data.
cc: Russell King <linux@arm.linux.org.uk>
cc: Alan Cox <alan@linux.intel.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Govindraj.R <govindraj.raja@ti.com>
cc: Kevin Hilman <khilman@ti.com>
cc: linux-serial@vger.kernel.org
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Instead of using cpu_is_omap..() macros in the device driver we
rely on information provided in the platform data.
The only information we need is whether the USB Host module has
a single ULPI bypass control bit for all ports or individual bypass
control bits for each port. OMAP3 REV2.1 and earlier have the former.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
[tony@atomide.com: updated to remove plat/cpu.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Ethernet is not currently working on the OMAP2420 H4 board. In commit
f604931 (ARM: OMAP: abstract debug card setup (smc, leds)) the function
h4_init_smc91x() that initialised the ethernet controller was renamed to
h4_init_debug() but was never called when initialising the board.
Adding a call to h4_init_debug() fixes ethernet support, however,
instead of using the legacy H4 code migrate the H4 to use the
gpmc_smc91x_init() function instead and remove the legacy H4 code.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_MODE_GPIO() macro verified only OMAP_MUX_MODE4.
It is not correct for following platforms:
2430 - gpio mux mode 3
44xx - gpio mux mode 3
54xx - gpio mux mode 6
Patch reserves first 3 bits in partition flags for storing gpio mux
mode in same format as stored in control pad register.
Modified OMAP_MODE_GPIO() macro to handle all possible cases of gpio mux mode.
Modified omap_mux_init() flags of omap34xx to include OMAP_MUX_GPIO_IN_MODE4.
Signed-off-by: Oleg Matcovschi <oleg.matcovschi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The i2c handling in tfp410 driver, which handles converting parallel RGB
to DVI, was changed in 958f2717b8
(OMAPDSS: TFP410: pdata rewrite). The patch changed what value the
driver considers as invalid/undefined. Before the patch, 0 was the
invalid value, but as 0 is a valid bus number, the patch changed this to
-1.
However, the fact was missed that many board files do not define the bus
number at all, thus it's left to 0. This causes the driver to fail to
get the i2c bus, exiting from the driver's probe with an error, meaning
that the DVI output does not work for those boards.
This patch fixes the issue by changing the i2c_bus number field in the
driver's platform data from u16 to int, and setting the bus number to -1
in the board files for the boards that did not define the bus. The
exception is devkit8000, for which the bus is set to 1, which is the
correct bus for that board.
The bug exists in v3.5+ kernels.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Thomas Weber <thomas@tomweber.eu>
Cc: Thomas Weber <thomas@tomweber.eu>
Cc: <stable@vger.kernel.org> # v3.5+
Signed-off-by: Tony Lindgren <tony@atomide.com>
Sparse generates the following warnings when compiling mach-omap2/timer.c.
CHECK arch/arm/mach-omap2/timer.c
arch/arm/mach-omap2/timer.c:193:13: warning: symbol 'omap_dmtimer_init'
was not declared. Should it be static?
arch/arm/mach-omap2/timer.c:213:12: warning: symbol
'omap_dm_timer_get_errata' was not declared. Should it be static?
Add static to function declaration to fix warnings.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
When compiling the kernel with configuration options ...
# CONFIG_ARCH_OMAP2 is not set
# CONFIG_ARCH_OMAP3 is not set
# CONFIG_ARCH_OMAP4 is not set
# CONFIG_SOC_OMAP5 is not set
CONFIG_SOC_AM33XX=y
... the following build warning is seen.
CC arch/arm/mach-omap2/timer.o
arch/arm/mach-omap2/timer.c:395:19: warning: ‘omap2_sync32k_clocksource_init’
defined but not used [-Wunused-function]
This issue was introduced by commit 6f80b3b (ARM: OMAP2+: timer: remove
CONFIG_OMAP_32K_TIMER) where the omap2_sync32k_clocksource_init() is no
longer referenced by the timer initialisation function for the AM335x
device as it has no 32k-sync timer.
Fix this by adding the "__maybe_unused" compiler directive to the
omap2_sync32k_clocksource_init() function to indicate that this function
may be used for certain configurations.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
In commit fa6d79d (ARM: OMAP: Add initialisation for the real-time
counter), the function realtime_counter_init() was added. However, if
the kernel configuration option CONFIG_SOC_OMAP5 is not selected then
the following compiler warning is observed.
CC arch/arm/mach-omap2/timer.o
arch/arm/mach-omap2/timer.c:489:20: warning: ‘realtime_counter_init’
defined but not used [-Wunused-function]
Commit fa6d79d also introduced the kernel configuration option
CONFIG_SOC_HAS_REALTIME_COUNTER. If this option is not selected then the
a stub function for realtime_counter_init() is defined.
For non-OMAP5 devices, there is no realtime counter and so
realtime_counter_init() function and stub function are not used for
these devices. Therefore, fix this warning by only allowing the kernel
configuration option CONFIG_SOC_HAS_REALTIME_COUNTER to be enabled for
OMAP5 devices.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by Santosh Shilimkar <santosh.shilimkar@ti.com>
Pull media updates from Mauro Carvalho Chehab:
- Missing MAINTAINERS entries were added for several drivers
- Adds V4L2 support for DMABUF handling, allowing zero-copy buffer
sharing between V4L2 devices and GPU
- Got rid of all warnings when compiling with W=1 on x86
- Add a new driver for Exynos hardware (s3c-camif)
- Several bug fixes, cleanups and driver improvements
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (243 commits)
[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
[media] omap3isp: Prepare/unprepare clocks before/after enable/disable
[media] omap3isp: preview: Add support for 8-bit formats at the sink pad
[media] omap3isp: Replace printk with dev_*
[media] omap3isp: Find source pad from external entity
[media] omap3isp: Configure CSI-2 phy based on platform data
[media] omap3isp: Add PHY routing configuration
[media] omap3isp: Add CSI configuration registers from control block to ISP resources
[media] omap3isp: Remove unneeded module memory address definitions
[media] omap3isp: Use monotonic timestamps for statistics buffers
[media] uvcvideo: Fix control value clamping for unsigned integer controls
[media] uvcvideo: Mark first output terminal as default video node
[media] uvcvideo: Add VIDIOC_[GS]_PRIORITY support
[media] uvcvideo: Return -ENOTTY for unsupported ioctls
[media] uvcvideo: Set device_caps in VIDIOC_QUERYCAP
[media] uvcvideo: Don't fail when an unsupported format is requested
[media] uvcvideo: Return -EACCES when trying to access a read/write-only control
[media] uvcvideo: Set error_idx properly for extended controls API failures
[media] rtl28xxu: add NOXON DAB/DAB+ USB dongle rev 2
[media] fc2580: write some registers conditionally
...
This branch contains a largeish set of updates of power management and
clock setup. The bulk of it is for OMAP/AM33xx platforms, but also a
few around hotplug/suspend/resume on Exynos.
It includes a split-up of some of the OMAP clock data into separate
files which adds to the diffstat, but gross delta is fairly reasonable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=h2Qo
-----END PGP SIGNATURE-----
Merge tag 'pm-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC power management and clock changes from Olof Johansson:
"This branch contains a largeish set of updates of power management and
clock setup. The bulk of it is for OMAP/AM33xx platforms, but also a
few around hotplug/suspend/resume on Exynos.
It includes a split-up of some of the OMAP clock data into separate
files which adds to the diffstat, but gross delta is fairly reasonable."
* tag 'pm-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
watchdog: OMAP: fixup for ARM multiplatform support
ARM: EXYNOS: Add flush_cache_all in suspend finisher
ARM: EXYNOS: Remove scu_enable from cpuidle
ARM: EXYNOS: Fix soft reboot hang after suspend/resume
ARM: EXYNOS: Add support for rtc wakeup
ARM: EXYNOS: fix the hotplug for Cortex-A15
ARM: OMAP2+: omap_device: Correct resource handling for DT boot
ARM: OMAP2+: hwmod: Add possibility to count hwmod resources based on type
ARM: OMAP2+: hwmod: Add support for per hwmod/module context lost count
ARM: OMAP2+: PRM: initialize some PRM functions early
ARM: OMAP2+: voltage: fixup oscillator handling when CONFIG_PM=n
ARM: OMAP4: USB: power down MUSB PHY during boot
ARM: OMAP2+: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP2xxx: clock: drop obsolete clock data
ARM: OMAP2: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP3+: DPLL: drop !CONFIG_COMMON_CLK sections
ARM: AM33xx: clock: drop obsolete clock data
ARM: OMAP3xxx: clk: drop obsolete clock data
...
OMAPDSS changes for 3.8, including:
- use dynanic debug prints
- OMAP platform dependency removals
- Creation of compat-layer, helping us to improve omapdrm
- Misc cleanups, aiming to make omadss more in line with the upcoming common
display framework
* tag 'omapdss-for-3.8' of git://gitorious.org/linux-omap-dss2/linux: (140 commits)
OMAPDSS: fix TV-out issue with DSI PLL
Revert "OMAPFB: simplify locking"
OMAPFB: remove silly loop in fb2display()
OMAPFB: fix error handling in omapfb_find_best_mode()
OMAPFB: use devm_kzalloc to allocate omapfb2_device
OMAPDSS: DISPC: remove dispc fck uses
OMAPDSS: DISPC: get dss clock rate from dss driver
OMAPDSS: use omapdss_compat_init() in other drivers
OMAPDSS: export dispc functions
OMAPDSS: export dss_feat functions
OMAPDSS: export dss_mgr_ops functions
OMAPDSS: separate compat files in the Makefile
OMAPDSS: move display sysfs init to compat layer
OMAPDSS: DPI: use dispc's check_timings
OMAPDSS: DISPC: add dispc_ovl_check()
OMAPDSS: move irq handling to dispc-compat
OMAPDSS: move omap_dispc_wait_for_irq_interruptible_timeout to dispc-compat.c
OMAPDSS: move blocking mgr enable/disable to compat layer
OMAPDSS: manage framedone irq with mgr ops
OMAPDSS: add manager ops
...
Pull networking changes from David Miller:
1) Allow to dump, monitor, and change the bridge multicast database
using netlink. From Cong Wang.
2) RFC 5961 TCP blind data injection attack mitigation, from Eric
Dumazet.
3) Networking user namespace support from Eric W. Biederman.
4) tuntap/virtio-net multiqueue support by Jason Wang.
5) Support for checksum offload of encapsulated packets (basically,
tunneled traffic can still be checksummed by HW). From Joseph
Gasparakis.
6) Allow BPF filter access to VLAN tags, from Eric Dumazet and
Daniel Borkmann.
7) Bridge port parameters over netlink and BPDU blocking support
from Stephen Hemminger.
8) Improve data access patterns during inet socket demux by rearranging
socket layout, from Eric Dumazet.
9) TIPC protocol updates and cleanups from Ying Xue, Paul Gortmaker, and
Jon Maloy.
10) Update TCP socket hash sizing to be more in line with current day
realities. The existing heurstics were choosen a decade ago.
From Eric Dumazet.
11) Fix races, queue bloat, and excessive wakeups in ATM and
associated drivers, from Krzysztof Mazur and David Woodhouse.
12) Support DOVE (Distributed Overlay Virtual Ethernet) extensions
in VXLAN driver, from David Stevens.
13) Add "oops_only" mode to netconsole, from Amerigo Wang.
14) Support set and query of VEB/VEPA bridge mode via PF_BRIDGE, also
allow DCB netlink to work on namespaces other than the initial
namespace. From John Fastabend.
15) Support PTP in the Tigon3 driver, from Matt Carlson.
16) tun/vhost zero copy fixes and improvements, plus turn it on
by default, from Michael S. Tsirkin.
17) Support per-association statistics in SCTP, from Michele
Baldessari.
And many, many, driver updates, cleanups, and improvements. Too
numerous to mention individually.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
net/mlx4_en: Add support for destination MAC in steering rules
net/mlx4_en: Use generic etherdevice.h functions.
net: ethtool: Add destination MAC address to flow steering API
bridge: add support of adding and deleting mdb entries
bridge: notify mdb changes via netlink
ndisc: Unexport ndisc_{build,send}_skb().
uapi: add missing netconf.h to export list
pkt_sched: avoid requeues if possible
solos-pci: fix double-free of TX skb in DMA mode
bnx2: Fix accidental reversions.
bna: Driver Version Updated to 3.1.2.1
bna: Firmware update
bna: Add RX State
bna: Rx Page Based Allocation
bna: TX Intr Coalescing Fix
bna: Tx and Rx Optimizations
bna: Code Cleanup and Enhancements
ath9k: check pdata variable before dereferencing it
ath5k: RX timestamp is reported at end of frame
ath9k_htc: RX timestamp is reported at end of frame
...
This branch contains a set of various board updates for ARM platforms.
A few shmobile platforms that are stale have been removed, some
defconfig updates for various boards selecting new features such as
pinctrl subsystem support, and various updates enabling peripherals, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=sgYz
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"This branch contains a set of various board updates for ARM platforms.
A few shmobile platforms that are stale have been removed, some
defconfig updates for various boards selecting new features such as
pinctrl subsystem support, and various updates enabling peripherals,
etc."
Fix up conflicts mostly as per Olof.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
ARM: S3C64XX: Add dummy supplies for Glenfarclas LDOs
ARM: S3C64XX: Add registration of WM2200 Bells device on Cragganmore
ARM: kirkwood: Add Plat'Home OpenBlocks A6 support
ARM: Dove: update defconfig
ARM: Kirkwood: update defconfig for new boards
arm: orion5x: add DT related options in defconfig
arm: orion5x: convert 'LaCie Ethernet Disk mini v2' to Device Tree
arm: orion5x: basic Device Tree support
arm: orion5x: mechanical defconfig update
ARM: kirkwood: Add support for the MPL CEC4
arm: kirkwood: add support for ZyXEL NSA310
ARM: Kirkwood: new board USI Topkick
ARM: kirkwood: use gpio-fan DT binding on lsxl
ARM: Kirkwood: add Netspace boards to defconfig
ARM: kirkwood: DT board setup for Network Space Mini v2
ARM: kirkwood: DT board setup for Network Space Lite v2
ARM: kirkwood: DT board setup for Network Space v2 and parents
leds: leds-ns2: add device tree binding
ARM: Kirkwood: Enable the second I2C bus
ARM: mmp: select pinctrl driver
...
Cleanup patches for various ARM platforms and some of their associated
drivers. There's also a branch in here that enables Freescale i.MX to be
part of the multiplatform support -- the first "big" SoC that is moved
over (more multiplatform work comes in a separate branch later during
the merge window).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=zfPd
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups on various subarchitectures from Olof Johansson:
"Cleanup patches for various ARM platforms and some of their associated
drivers. There's also a branch in here that enables Freescale i.MX to
be part of the multiplatform support -- the first "big" SoC that is
moved over (more multiplatform work comes in a separate branch later
during the merge window)."
Conflicts fixed as per Olof, including a silent semantic one in
arch/arm/mach-omap2/board-generic.c (omap_prcm_restart() was renamed to
omap3xxx_restart(), and a new user of the old name was added).
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (189 commits)
ARM: omap: fix typo on timer cleanup
ARM: EXYNOS: Remove unused regs-mem.h file
ARM: EXYNOS: Remove unused non-dt support for dwmci controller
ARM: Kirkwood: Use hw_pci.ops instead of hw_pci.scan
ARM: OMAP3: cm-t3517: use GPTIMER for system clock
ARM: OMAP2+: timer: remove CONFIG_OMAP_32K_TIMER
ARM: SAMSUNG: use devm_ functions for ADC driver
ARM: EXYNOS: no duplicate mask/unmask in eint0_15
ARM: S3C24XX: SPI clock channel setup is fixed for S3C2443
ARM: EXYNOS: Remove i2c0 resource information and setting of device names
ARM: Kirkwood: checkpatch cleanups
ARM: Kirkwood: Fix sparse warnings.
ARM: Kirkwood: Remove unused includes
ARM: kirkwood: cleanup lsxl board includes
ARM: integrator: use BUG_ON where possible
ARM: integrator: push down SC dependencies
ARM: integrator: delete static UART1 mapping
ARM: integrator: delete SC mapping on the CP
ARM: integrator: remove static CP syscon mapping
ARM: integrator: remove static AP syscon mapping
...
This is a collection of header file cleanups, mostly for OMAP and AT91,
that keeps moving the platforms in the direction of multiplatform by
removing the need for mach-dependent header files used in drivers and
other places.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=aggA
-----END PGP SIGNATURE-----
Merge tag 'headers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC Header cleanups from Olof Johansson:
"This is a collection of header file cleanups, mostly for OMAP and
AT91, that keeps moving the platforms in the direction of
multiplatform by removing the need for mach-dependent header files
used in drivers and other places."
Fix up mostly trivial conflicts as per Olof.
* tag 'headers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (106 commits)
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
atmel: move ATMEL_MAX_UART to platform_data/atmel.h
ARM: OMAP: Remove omap_init_consistent_dma_size()
arm: at91: move at91rm9200 rtc header in drivers/rtc
arm: at91: move reset controller header to arm/arm/mach-at91
arm: at91: move pit define to the driver
arm: at91: move at91_shdwc.h to arch/arm/mach-at91
arm: at91: move board header to arch/arm/mach-at91
arn: at91: move at91_tc.h to arch/arm/mach-at91
arm: at91 move at91_aic.h to arch/arm/mach-at91
arm: at91 move board.h to arch/arm/mach-at91
arm: at91: move platfarm_data to include/linux/platform_data/atmel.h
arm: at91: drop machine defconfig
ARM: OMAP: Remove NEED_MACH_GPIO_H
ARM: OMAP: Remove unnecessary mach and plat includes
...
Simple bug fixes that were not considered important enough for inclusion
into 3.7, especially those that arrived late during the merge window.
There's also a MAINTAINERS update for the Renesas platforms in here,
marking Simon Horman as a maintainer and changing the git url to his tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Lcpo
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC Non-critical bug fixes from Olof Johansson:
"Simple bug fixes that were not considered important enough for
inclusion into 3.7, especially those that arrived late during the
merge window.
There's also a MAINTAINERS update for the Renesas platforms in here,
marking Simon Horman as a maintainer and changing the git url to his
tree."
* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
Update ARM/SHMOBILE section of MAINTAINERS
ARM: Fix Kconfig symbols typo for LEDS
ARM: pxa: add dummy SA1100 rtc clock in pxa25x
ARM: pxa: fix pxa25x gpio wakeup setting
ARM: OMAP4: PM: fix errata handling when CONFIG_PM=n
ARM: cns3xxx: drop unnecessary symbol selection
ARM: vexpress: fix ll debug code when building multiplatform
ARM: OMAP4: retrigger localtimers after re-enabling gic
ARM: OMAP4460: Workaround for ROM bug because of CA9 r2pX GIC control register change.
ARM: OMAP4: PM: add errata support
ARM: davinci: fix return value check by using IS_ERR in tnetv107x_devices_init()
ARM: davinci: uncompress.h: bail out if uart not initialized
ARM: davinci: serial.h: fix uart number in the comment
ARM: davinci: dm644x evm: move pointer dereference below NULL check
ARM: vexpress: Make the debug UART detection more specific
Pull ARM updates from Russell King:
"Here's the updates for ARM for this merge window, which cover quite a
variety of areas.
There's a bunch of patch series from Will tackling various bugs like
the PROT_NONE handling, ASID allocation, cluster boot protocol and
ASID TLB tagging updates.
We move to a build-time sorted exception table rather than doing the
sorting at run-time, add support for the secure computing filter, and
some updates to the perf code. We also have sorted out the placement
of some headers, fixed some build warnings, fixed some hotplug
problems with the per-cpu TWD code."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (73 commits)
ARM: 7594/1: Add .smp entry for REALVIEW_EB
ARM: 7599/1: head: Remove boot-time HYP mode check for v5 and below
ARM: 7598/1: net: bpf_jit_32: fix sp-relative load/stores offsets.
ARM: 7595/1: syscall: rework ordering in syscall_trace_exit
ARM: 7596/1: mmci: replace readsl/writesl with ioread32_rep/iowrite32_rep
ARM: 7597/1: net: bpf_jit_32: fix kzalloc gfp/size mismatch.
ARM: 7593/1: nommu: do not enable DCACHE_WORD_ACCESS when !CONFIG_MMU
ARM: 7592/1: nommu: prevent generation of kernel unaligned memory accesses
ARM: 7591/1: nommu: Enable the strict alignment (CR_A) bit only if ARCH < v6
ARM: 7590/1: /proc/interrupts: limit the display of IPIs to online CPUs only
ARM: 7587/1: implement optimized percpu variable access
ARM: 7589/1: integrator: pass the lm resource to amba
ARM: 7588/1: amba: create a resource parent registrator
ARM: 7582/2: rename kvm_seq to vmalloc_seq so to avoid confusion with KVM
ARM: 7585/1: kernel: fix nr_cpu_ids check in DT logical map init
ARM: 7584/1: perf: fix link error when CONFIG_HW_PERF_EVENTS is not selected
ARM: gic: use a private mapping for CPU target interfaces
ARM: kernel: add logical mappings look-up
ARM: kernel: add cpu logical map DT init in setup_arch
ARM: kernel: add device tree init map function
...
Here's the big staging tree merge for 3.8-rc1
There's a lot of patches in here, the majority being the comedi rework/cleanup
that has been ongoing and is causing a huge reduction in overall code size,
which is amazing to watch. We also removed some older drivers (telephony and
rts_pstor), and added a new one (fwserial which also came in through the tty
tree due to tty api changes, take that one if you get merge conflicts.)
The iio and ipack drivers are moving out of the staging area into their
own part of the kernel as they have been cleaned up sufficiently and are
working well.
Overall, again a reduction of code:
768 files changed, 31887 insertions(+), 82166 deletions(-)
All of this has been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHiRkACgkQMUfUDdst+ykyCgCglEbrWzevtCOl+C2KAmIR+Jnt
qUsAoLOXYeQq1aadxzqh3tK+ytlMrWd1
=Ync9
-----END PGP SIGNATURE-----
Merge tag 'staging-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver tree merge from Greg Kroah-Hartman:
"Here's the big staging tree merge for 3.8-rc1
There's a lot of patches in here, the majority being the comedi
rework/cleanup that has been ongoing and is causing a huge reduction
in overall code size, which is amazing to watch. We also removed some
older drivers (telephony and rts_pstor), and added a new one (fwserial
which also came in through the tty tree due to tty api changes, take
that one if you get merge conflicts.)
The iio and ipack drivers are moving out of the staging area into
their own part of the kernel as they have been cleaned up sufficiently
and are working well.
Overall, again a reduction of code:
768 files changed, 31887 insertions(+), 82166 deletions(-)
All of this has been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1298 commits)
iio: imu: adis16480: remove duplicated include from adis16480.c
iio: gyro: adis16136: remove duplicated include from adis16136.c
iio:imu: adis16480: show_firmware() buffer too small
iio:gyro: adis16136: divide by zero in write_frequency()
iio: adc: Add Texas Instruments ADC081C021/027 support
iio:ad7793: Add support for the ad7796 and ad7797
iio:ad7793: Add support for the ad7798 and ad7799
staging:iio: Move ad7793 driver out of staging
staging:iio:ad7793: Implement stricter id checking
staging:iio:ad7793: Move register definitions from header to source
staging:iio:ad7793: Rework regulator handling
staging:iio:ad7793: Rework platform data
staging:iio:ad7793: Use kstrtol instead of strict_strtol
staging:iio:ad7793: Use usleep_range instead of msleep
staging:iio:ad7793: Fix temperature scale
staging:iio:ad7793: Fix VDD monitor scale
staging: gdm72xx: unlock on error in init_usb()
staging: panel: pass correct lengths to keypad_send_key()
staging: comedi: addi_apci_2032: fix interrupt support
staging: comedi: addi_apci_2032: move i_APCI2032_ConfigDigitalOutput()
...
This prevents hwmod _enable_clocks...omap2_dflt_clk_enable path
from enabling modulemode inside CLKCTRL using its clk->enable_reg
field. Instead is left to _omap4_enable_module though soc_ops, as
the one in charge of this setting.
According to comments received[1] for related patches the idea is
to get rid of leaf clocks in future. So remove these two while at it.
[1] http://lkml.org/lkml/2012/8/20/226
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Use runtime PM functionality interfaced with hwmod enable/idle
functions, to replace direct clock operations and sysconfig
handling.
Due to reset sequence, pm_runtime_[get|put]_sync must be used, to
avoid possible operations with the module under reset. Because of
this and given that the driver uses spin_locks to protect their
critical sections, we must use pm_runtime_irq_safe in order for the
runtime ops to be happy, otherwise might_sleep_if checks in runtime
framework will complain.
The remaining pm_runtime out of iommu_enable and iommu_disable
corresponds to paths that can be accessed through debugfs, some of
them doesn't work if the module is not enabled first, but in future
if the mmu is idled withouth freeing, these are needed to debug.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Use hwmod data and device attributes to build and register an
omap device for iommu driver.
- Update the naming convention in isp module.
- Remove unneeded check for number of resources, as this is now
handled by omap_device and prevents driver from loading.
- Now unused, remove platform device and resource data, handling
of sysconfig register for softreset purposes, use default
latency structure.
- Use hwmod API for reset handling.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
enabled. Unfortunately the DMA header patch had to be redone
to avoid adding new multiplatform specific include paths, the
other patches are just trivial compile fixes.
Note that this does not yet contain the necessary Kconfig
changes as we are still waiting for some drivers to get
fixed up first.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=w+UN
-----END PGP SIGNATURE-----
Merge tag 'tags/omap-for-v3.8/cleanup-multiplatform-no-clock-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/pm2
From Tony Lindgren:
Remaining patches to allow omap2+ to build with multiplatform
enabled. Unfortunately the DMA header patch had to be redone
to avoid adding new multiplatform specific include paths, the
other patches are just trivial compile fixes.
Note that this does not yet contain the necessary Kconfig
changes as we are still waiting for some drivers to get
fixed up first.
* tag 'tags/omap-for-v3.8/cleanup-multiplatform-no-clock-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
watchdog: OMAP: fixup for ARM multiplatform support
Conflicts due to surrounding changes in:
arch/arm/mach-omap2/omap_hwmod_2420_data.c
arch/arm/mach-omap2/omap_hwmod_2430_data.c
Signed-off-by: Olof Johansson <olof@lixom.net>
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yFcc
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/headers
From Tony Lindgren:
Move most of remaining omap iommu code to drivers/iommu.
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
* tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
Conflicts due to surrounding changes in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
drivers/media/platform/omap3isp/ispvideo.c
Signed-off-by: Olof Johansson <olof@lixom.net>
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yFcc
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
Move most of remaining omap iommu code to drivers/iommu.
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
* tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
Conflicts due to surrounding changes fixed up in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
drivers/media/platform/omap3isp/ispvideo.c
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim:
* 'next/pm-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Add flush_cache_all in suspend finisher
ARM: EXYNOS: Remove scu_enable from cpuidle
ARM: EXYNOS: Fix soft reboot hang after suspend/resume
ARM: EXYNOS: Add support for rtc wakeup
ARM: EXYNOS: fix the hotplug for Cortex-A15
+ Linux 3.7-rc6
Based on earlier discussions[1] we attempted to find a suitable
location for the omap DMA header in commit 2b6c4e73 (ARM: OMAP:
DMA: Move plat/dma.h to plat-omap/dma-omap.h) until the conversion
to dmaengine is complete.
Unfortunately that was before I was able to try to test compile
of the ARM multiplatform builds for omap2+, and the end result
was not very good.
So I'm creating yet another all over the place patch to cut the
last dependency for building omap2+ for ARM multiplatform. After
this, we have finally removed the driver dependencies to the
arch/arm code, except for few drivers that are being worked on.
The other option was to make the <plat-omap/dma-omap.h> path
to work, but we'd have to add some new header directory to for
multiplatform builds.
Or we would have to manually include arch/arm/plat-omap/include
again from arch/arm/Makefile for omap2+.
Neither of these alternatives sound appealing as they will
likely lead addition of various other headers exposed to the
drivers, which we want to avoid for the multiplatform kernels.
Since we already have a minimal include/linux/omap-dma.h,
let's just use that instead and add a note to it to not
use the custom omap DMA functions any longer where possible.
Note that converting omap DMA to dmaengine depends on
dmaengine supporting automatically incrementing the FIFO
address at the device end, and converting all the remaining
legacy drivers. So it's going to be few more merge windows.
[1] https://patchwork.kernel.org/patch/1519591/#
cc: Russell King <linux@arm.linux.org.uk>
cc: Kevin Hilman <khilman@ti.com>
cc: "Benoît Cousson" <b-cousson@ti.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Vinod Koul <vinod.koul@intel.com>
cc: Dan Williams <djbw@fb.com>
cc: Mauro Carvalho Chehab <mchehab@infradead.org>
cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
cc: David Woodhouse <dwmw2@infradead.org>
cc: Kyungmin Park <kyungmin.park@samsung.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
cc: Hans Verkuil <hans.verkuil@cisco.com>
cc: Vaibhav Hiremath <hvaibhav@ti.com>
cc: Lokesh Vutla <lokeshvutla@ti.com>
cc: Rusty Russell <rusty@rustcorp.com.au>
cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
cc: Afzal Mohammed <afzal@ti.com>
cc: linux-crypto@vger.kernel.org
cc: linux-media@vger.kernel.org
cc: linux-mtd@lists.infradead.org
cc: linux-usb@vger.kernel.org
cc: linux-fbdev@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some miscellaneous OMAP hwmod changes for 3.8, along with a PRM
change needed for one of the hwmod patches to function.
Basic test logs for this branch on top of Tony's
omap-for-v3.8/clock branch at commit
558a0780b0 are here:
http://www.pwsan.com/omap/testlogs/hwmod_devel_a_3.8/20121121161522/
However, omap-for-v3.8/clock at 558a0780 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_hwmod_devel_a_3.8/20121121162719/
which indicate that the series tests cleanly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JSAM
-----END PGP SIGNATURE-----
Merge tag 'tags/omap-for-v3.8/devel-prcm-signed' into omap-for-v3.8/cleanup-headers-prepare-multiplatform-v3
omap prcm changes via Paul Walmsley <paul@pwsan.com>:
Some miscellaneous OMAP hwmod changes for 3.8, along with a PRM
change needed for one of the hwmod patches to function.
Basic test logs for this branch on top of Tony's
omap-for-v3.8/clock branch at commit
558a0780b0 are here:
http://www.pwsan.com/omap/testlogs/hwmod_devel_a_3.8/20121121161522/
However, omap-for-v3.8/clock at 558a0780 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_hwmod_devel_a_3.8/20121121162719/
which indicate that the series tests cleanly.
Conflicts:
arch/arm/mach-omap2/cm33xx.c
arch/arm/mach-omap2/io.c
arch/arm/mach-omap2/prm_common.c
Fix 32 vs 32k typo:
arch/arm/mach-omap2/timer.c: In function 'omap4_local_timer_init':
arch/arm/mach-omap2/timer.c:633:2: error: implicit declaration of function 'omap4_sync32_timer_init' [-Werror=implicit-function-declaration]
arch/arm/mach-omap2/timer.c: At top level:
arch/arm/mach-omap2/timer.c:610:2: warning: 'omap4_sync32k_timer_init' defined but not used [-Wunused-function]
Also, mark the omap4_local_timer_init() stub as __init (and take off
the explicit inline and let the compiler do the work instead).
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
