lx2160a supports pw20 which could help save more power during cpu is
dile. It needs system firmware support via PSCI.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
v2 of "clk: imx: Refactor entire sccg pll clk" dropped the implicit
reparenting of the PLL output from the bypass clock to the real
PLL. The commit introducing the GPU node had only been tested against
v1 of this patch. Without an explicit reparent to the real PLL the
GPU is stuck at the bypass clock rate of 25MHz, serverly hampering
performance.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Link the SW1AB regulator to the GPU domain, so that it gets enabled
when needed.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is very similar to imx8mq cpufreq-dt support.
Operating points are from datasheet:
https://www.nxp.com/docs/en/data-sheet/IMX8MMCEC.pdf
Higher opps were omitted (just like imx8mq) because it requires checking
speed grade from OCOTP fuses.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add an initial description of the i2c1 bus with a pca9646 i2c switch and
various gpio expanders and sensors behind that. Only add the sensors
which already have upstream drivers.
According to the datasheet the pca9646 is software compatible with
pca9546 so no driver changes should be required.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX8QXP, SCU uses MU1 general interrupt channel #3 to notify
user for IRQs of RTC alarm, thermal alarm and WDOG etc., mailbox
RX doorbell mode is used for this function, this patch adds
support for it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This enables the Vivante GC7000L GPU on the i.MX8MQ SoC.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Zii Ultra design, also known as RDU3, is the i.MX8M based successor
to the the i.MX6 based RDU2. This adds the basic board support for all
components which are supported by the upstream kernel at this time.
The board comes in 2 different versions, called RMB3 and Zest, which
are derived from the same design, but have different layouts and a
few small differences in the populated components.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the datasheet both industrial and consumer variants support
at least 1.3GHz CPU frequency at 1.0V. Only the OPP at 1.5GHz is
unavailable on some SKUs and thus need further fuse reading support.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to NXP's FAE feedback and a comment in ATF firmware, PCIE1
and PCIE2 power domains can't really be used independently. Due to
shared reset line both power domains have to be turned on at the same
time. Account for that quirk by combining PCIE power domains into a
single 'pgc_pcie' power domain.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Mark iomuxc_gpr as compatible with "fsl,imx6q-iomuxc-gpr" in order for
to allow i.MX6 PCIe driver to use it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
lpuart nodes are part of the ADMA subsystem. See Audio DMA
memory map in iMX8 QXP RM [1]
This patch is based on the dtsi file initially submitted by
Teo Hall in i.MX NXP internal tree.
[1] https://www.nxp.com/docs/en/reference-manual/IMX8DQXPRM.pdf
Signed-off-by: Teo Hall <teo.hall@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add SATA device nodes for fsl-lx2160a and enable support
for QDS and RDB boards.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ls1028a SATA ecc address with more than 32 bit, so we should corrrect the
address.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Set ahb clock on sdma1 to get rid of "Timeout waiting for CH0"
on the imx8mq.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix a typo in the compatible string
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
thermal-zones node does not have any register properties and thus
shouldn't be placed inside the bus.
Move thermal-zones node from soc node to root node in order to fix
the following build warning with W=1:
arch/arm64/boot/dts/freescale/imx8mq.dtsi:305.18-364.6: Warning (simple_bus_reg): /soc@0/bus@30000000/thermal-zones: missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M Mini is new SOC of the i.MX8M family. it is
focused on delivering the latest and greatest video and
audio experience combining state-of-the-art media-specific
features with high-performance processing while optimized
for lowest power consumption. The i.MX 8M Mini Media Applications
Processor is 14nm FinFET product of the growing i.MX8M family
targeting the consumer & industrial market. It is built in 14LPP
to achieve both high performance and low power consumption
and relies on a powerful fully coherent core complex based on
a quad Cortex-A53 cluster with video and graphics accelerators
This patch adds the basic dtsi support for i.MX8MM.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move opp-table node from soc node to root node.
opp-table node does not have any register properties and thus
shouldn't be placed inside the bus.
This fixes the following build warnings with W=1:
arch/arm64/boot/dts/freescale/imx8mq.dtsi:687.28-703.5: Warning (simple_bus_reg): /soc@0/opp-table: missing or empty reg/ranges property
Fixes: 64d26f8c1d ("arm64: dts: imx8mq: Add the opp table and cores opp properties")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
crypto node alias is needed by U-boot to identify the node and
perform fix-ups, like adding "fsl,sec-era" property or deleting
a job ring child node (in case ARM TF-A is running).
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After switching to the new FSL QSPI driver the properties
'fsl,qspi-has-second-chip' and 'big-endian' are not used anymore.
The driver now uses the 'reg' property to determine the bus and
the chipselect. The endianness is selected by the driver depending
on which SoC is used.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add lsio_mu2 node which could be used communicate with SCU.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently lsio_mu1 is used by Linux Kernel with mbox-cells as 2, but
actually mu0-4 could be used to communicate with SCU. So fix the
mbox-cells.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Fixes: 3d91ba65fe ("arm64: dts: imx: add imx8qxp support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable PCI-E controller for Oxalis board based on NXP/Freescale LS1012a
SoC available as the Mini PCI-E connector on the bottom side.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The main Audio DAC used on the EVK board is wm8524
The EVK provides the MCLK to wm8524.
Digital interface is SAI2 which includes three signals:
SYNC_CLK, BCLK and DACDAT.
This patch sets:
* SAI2 pinctrl configuration
* clock hierarchy
* wm8524 codec
Then uses simple-card machine driver to connect them
into a sound card.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SAI2 is part of AIPS-3 memory region.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SDMA1 is part of AIPS-3 region and SDMA2 is part
of AIPS-1 region.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MQ has clock gate for each GPIO bank, add clock info
to GPIO node for clock management.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the 0.8GHz and 1GHz opps. According to the datasheet:
https://www.nxp.com/docs/en/data-sheet/IMX8MDQLQIEC.pdf
section 3.1.3 Operating ranges.
The 0.8GHz opp runs in nominal mode with the regulator set to 0.9V.
The 1GHz runs in overdrive mode with the regulator set to 1V.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the schematics, this is a MP2147 switch converter
which is controlled by GPIO1_IO13. When set the gpio is set to
high the regulator output is set to 0.9V. When the gpio is set
to low the regulator output is set to 1V.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds Audio DT nodes for LS1028ARDB and LS1028AQDS boards.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the node for the OTP controller.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add i.MX8QXP CPU opp table to support cpufreq.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
No core changes.
New drivers:
- NXP (ex Freescale) i.MX 8QM driver.
- NXP (ex Freescale) i.MX 8MM driver.
- AT91 SAM9X60 subdriver.
Improvements:
- Support for external interrups (EINT) on Mediatek virtual GPIOs.
- Make BCM2835 pin config fully generic.
- Lots of Renesas SH-PFC incremental improvements.
-----BEGIN PGP SIGNATURE-----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=EfXK
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is a calm cycle, not much happened this time around: not even
much incremental development. Some three new drivers, that is all.
No core changes.
New drivers:
- NXP (ex Freescale) i.MX 8QM driver.
- NXP (ex Freescale) i.MX 8MM driver.
- AT91 SAM9X60 subdriver.
Improvements:
- Support for external interrups (EINT) on Mediatek virtual GPIOs.
- Make BCM2835 pin config fully generic.
- Lots of Renesas SH-PFC incremental improvements"
* tag 'pinctrl-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (70 commits)
pinctrl: imx: fix scu link errors
dt-bindings: pinctrl: Document the i.MX50 IOMUXC binding
pinctrl: qcom: spmi-gpio: Reorder debug print
pinctrl: nomadik: fix possible object reference leak
pinctrl: stm32: return error upon hwspinlock failure
pinctrl: stm32: fix memory leak issue
pinctrl: sh-pfc: r8a77965: Add DRIF pins, groups and functions
pinctrl: sh-pfc: r8a77965: Add TMU pins, groups and functions
pinctrl: sh-pfc: Validate fixed-size field widths at build time
pinctrl: sh-pfc: sh73a0: Fix fsic_spdif pin groups
pinctrl: sh-pfc: r8a7792: Fix vin1_data18_b pin group
pinctrl: sh-pfc: r8a7791: Fix scifb2_data_c pin group
pinctrl: sh-pfc: emev2: Add missing pinmux functions
pinctrl: sunxi: Support I/O bias voltage setting on A80
pinctrl: ingenic: Add LCD pins for the JZ4725B SoC
pinctrl: samsung: Remove legacy API for handling external wakeup interrupts mask
pinctrl: bcm2835: Direct GPIO config changes to generic pinctrl
pinctrl: bcm2835: declare pin config as generic
pinctrl: qcom: qcs404: Drop unused UFS_RESET macro
dt-bindings: add documentation for slew rate
...
-----BEGIN PGP SIGNATURE-----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=vf9L
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Use match_string() instead of reimplementing it (Andy Shevchenko)
- Enable SERR# forwarding for all bridges (Bharat Kumar Gogada)
- Use Latency Tolerance Reporting if already enabled by platform (Bjorn
Helgaas)
- Save/restore LTR info for suspend/resume (Bjorn Helgaas)
- Fix DPC use of uninitialized data (Dongdong Liu)
- Probe bridge window attributes only once at enumeration-time to fix
device accesses during rescan (Bjorn Helgaas)
- Return BAR size (not "size -1 ") from pci_size() to simplify code (Du
Changbin)
- Use config header type (not class code) identify bridges more
reliably (Honghui Zhang)
- Work around Intel Denverton incorrect Trace Hub BAR size reporting
(Alexander Shishkin)
- Reorder pciehp cached state/hardware state updates to avoid missed
interrupts (Mika Westerberg)
- Turn ibmphp semaphores into completions or mutexes (Arnd Bergmann)
- Mark expected switch fall-through (Mathieu Malaterre)
- Use of_node_name_eq() for node name comparisons (Rob Herring)
- Add ACS and pciehp quirks for HXT SD4800 (Shunyong Yang)
- Consolidate Rohm Vendor ID definitions (Andy Shevchenko)
- Use u32 (not __u32) for things not exposed to userspace (Logan
Gunthorpe)
- Fix locking semantics of bus and slot reset interfaces (Alex
Williamson)
- Update PCIEPORTBUS Kconfig help text (Hou Zhiqiang)
- Allow portdrv to claim subtractive decode Ports so PCIe services will
work for them (Honghui Zhang)
- Report PCIe links that become degraded at run-time (Alexandru
Gagniuc)
- Blacklist Gigabyte X299 Root Port power management to fix Thunderbolt
hotplug (Mika Westerberg)
- Revert runtime PM suspend/resume callbacks that broke PME on network
cable plug (Mika Westerberg)
- Disable Data Link State Changed interrupts to prevent wakeup
immediately after suspend (Mika Westerberg)
- Extend altera to support Stratix 10 (Ley Foon Tan)
- Allow building altera driver on ARM64 (Ley Foon Tan)
- Replace Douglas with Tom Joseph as Cadence PCI host/endpoint
maintainer (Lorenzo Pieralisi)
- Add DT support for R-Car RZ/G2E (R8A774C0) (Fabrizio Castro)
- Add dra72x/dra74x/dra76x SoC compatible strings (Kishon Vijay Abraham I)
- Enable x2 mode support for dra72x/dra74x/dra76x SoC (Kishon Vijay
Abraham I)
- Configure dra7xx PHY to PCIe mode (Kishon Vijay Abraham I)
- Simplify dwc (remove unnecessary header includes, name variables
consistently, reduce inverted logic, etc) (Gustavo Pimentel)
- Add i.MX8MQ support (Andrey Smirnov)
- Add message to help debug dwc MSI-X mask bit errors (Gustavo
Pimentel)
- Work around imx7d PCIe PLL erratum (Trent Piepho)
- Don't assert qcom reset GPIO during probe (Bjorn Andersson)
- Skip dwc MSI init if MSIs have been disabled (Lucas Stach)
- Use memcpy_fromio()/memcpy_toio() instead of plain memcpy() in PCI
endpoint framework (Wen Yang)
- Add interface to discover supported endpoint features to replace a
bitfield that wasn't flexible enough (Kishon Vijay Abraham I)
- Implement the new supported-feature interface for designware-plat,
dra7xx, rockchip, cadence (Kishon Vijay Abraham I)
- Fix issues with 64-bit BAR in endpoints (Kishon Vijay Abraham I)
- Add layerscape endpoint mode support (Xiaowei Bao)
- Remove duplicate struct hv_vp_set in favor of struct hv_vpset (Maya
Nakamura)
- Rework hv_irq_unmask() to use cpumask_to_vpset() instead of
open-coded reimplementation (Maya Nakamura)
- Align Hyper-V struct retarget_msi_interrupt arguments (Maya Nakamura)
- Fix mediatek MMIO size computation to enable full size of available
MMIO space (Honghui Zhang)
- Fix mediatek DMA window size computation to allow endpoint DMA access
to full DRAM address range (Honghui Zhang)
- Fix mvebu prefetchable BAR regression caused by common bridge
emulation that assumed all bridges had prefetchable windows (Thomas
Petazzoni)
- Make advk_pci_bridge_emul_ops static (Wei Yongjun)
- Configure MPS settings for VMD root ports (Jon Derrick)
* tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (92 commits)
PCI: Update PCIEPORTBUS Kconfig help text
PCI: Fix "try" semantics of bus and slot reset
PCI/LINK: Report degraded links via link bandwidth notification
dt-bindings: PCI: altera: Add altr,pcie-root-port-2.0
PCI: altera: Enable driver on ARM64
PCI: altera: Add Stratix 10 PCIe support
PCI/PME: Fix possible use-after-free on remove
PCI: aardvark: Make symbol 'advk_pci_bridge_emul_ops' static
PCI: dwc: skip MSI init if MSIs have been explicitly disabled
PCI: hv: Refactor hv_irq_unmask() to use cpumask_to_vpset()
PCI: hv: Replace hv_vp_set with hv_vpset
PCI: hv: Add __aligned(8) to struct retarget_msi_interrupt
PCI: mediatek: Enlarge PCIe2AHB window size to support 4GB DRAM
PCI: mediatek: Fix memory mapped IO range size computation
PCI: dwc: Remove superfluous shifting in definitions
PCI: dwc: Make use of GENMASK/FIELD_PREP
PCI: dwc: Make use of BIT() in constant definitions
PCI: dwc: Share code for dw_pcie_rd/wr_other_conf()
PCI: dwc: Make use of IS_ALIGNED()
PCI: imx6: Add code to request/control "pcie_aux" clock for i.MX8MQ
...
This is a smaller update than the past few times, but with just over
500 non-merge changesets still dwarfes the rest of the SoC tree.
Three new SoC platforms get added, each one a follow-up to an existing
product, and added here in combination with a reference platform:
- Renesas RZ/A2M (R7S9210) 32-bit Cortex-A9 Real-time imaging processor
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rza/rza2m.html
- Renesas RZ/G2E (r8a774c0) 64-bit Cortex-A53 SoC "for
Rich Graphics Applications".
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rzg/rzg2e.html
- NXP i.MX8QuadXPlus 64-bit Cortex-A35 SoC
https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/i.mx-applications-processors/i.mx-8-processors/i.mx-8x-family-arm-cortex-a35-3d-graphics-4k-video-dsp-error-correcting-code-on-ddr:i.MX8X
These are actual commercial products we now support with an in-kernel
device tree source file:
- Bosch Guardian is a product made by Bosch Power
Tools GmbH, based on the Texas Instruments AM335x chip
- Winterland IceBoard is a Texas Instruments AM3874 based
machine used in telescopes at the south pole and elsewhere, see commit
d031773169 for some pointers:
- Inspur on5263m5 is an x86 server platform with an Aspeed
ast2500 baseboard management controller. This is for running on
the BMC.
- Zodiac Digital Tapping Unit, apparently a kind of ethernet
switch used in airplanes.
- Phicomm K3 is a WiFi router based on Broadcom bcm47094
- Methode Electronics uDPU FTTdp distribution point unit
- X96 Max, a generic TV box based on Amlogic G12a (S905X2)
- NVIDIA Shield TV (Darcy) based on Tegra210
And then there are several new SBC, evaluation, development or modular
systems that we add:
- Three new Rockchips rk3399 based boards:
- FriendlyElec NanoPC-T4 and NanoPi M4
- Radxa ROCK Pi 4
- Five new i.MX6 family SoM modules and boards for industrial
products:
- Logic PD i.MX6QD SoM and evaluation baseboad
- Y Soft IOTA Draco/Hydra/Ursa family boards based on i.MX6DL
- Phytec phyCORE i.MX6 UltraLite SoM and evaluation module
- MYIR Tech MYD-LPC4357 development based on the NXP lpc4357
microcontroller
- Chameleon96, an Intel/Altera Cyclone5 based FPGA development
system in 96boards form factor
- Arm Fixed Virtual Platforms(FVP) Base RevC, a purely
virtual platform for corresponding to the latest "fast model"
- Another Raspberry Pi variant: Model 3 A+, supported both
in 32-bit and 64-bit mode.
- Oxalis Evalkit V100 based on NXP Layerscape LS1012a,
in 96Boards enterprise form factor
- Elgin RV1108 R1 development board based on 32-bit Rockchips RV1108
For already supported boards and SoCs, we often add support for new
devices after merging the drivers. This time, the largest changes include
updates for
- STMicroelectronics stm32mp1, which was now formally
launched last week
- Qualcomm Snapdragon 845, a high-end phone and low-end laptop chip
- Action Semi S700
- TI AM654x, their recently merged 64-bit SoC from the OMAP family
- Various Amlogic Meson SoCs
- Mediatek MT2712
- NVIDIA Tegra186 and Tegra210
- The ancient NXP lpc32xx family
- Samsung s5pv210, used in some older mobile phones
Many other chips see smaller updates and bugfixes beyond that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=1goV
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"This is a smaller update than the past few times, but with just over
500 non-merge changesets still dwarfes the rest of the SoC tree.
Three new SoC platforms get added, each one a follow-up to an existing
product, and added here in combination with a reference platform:
- Renesas RZ/A2M (R7S9210) 32-bit Cortex-A9 Real-time imaging
processor:
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rza/rza2m.html
- Renesas RZ/G2E (r8a774c0) 64-bit Cortex-A53 SoC "for Rich Graphics
Applications":
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rzg/rzg2e.html
- NXP i.MX8QuadXPlus 64-bit Cortex-A35 SoC:
https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/i.mx-applications-processors/i.mx-8-processors/i.mx-8x-family-arm-cortex-a35-3d-graphics-4k-video-dsp-error-correcting-code-on-ddr:i.MX8X
These are actual commercial products we now support with an in-kernel
device tree source file:
- Bosch Guardian is a product made by Bosch Power Tools GmbH, based
on the Texas Instruments AM335x chip
- Winterland IceBoard is a Texas Instruments AM3874 based machine
used in telescopes at the south pole and elsewhere, see commit
d031773169 for some pointers:
- Inspur on5263m5 is an x86 server platform with an Aspeed ast2500
baseboard management controller. This is for running on the BMC.
- Zodiac Digital Tapping Unit, apparently a kind of ethernet switch
used in airplanes.
- Phicomm K3 is a WiFi router based on Broadcom bcm47094
- Methode Electronics uDPU FTTdp distribution point unit
- X96 Max, a generic TV box based on Amlogic G12a (S905X2)
- NVIDIA Shield TV (Darcy) based on Tegra210
And then there are several new SBC, evaluation, development or modular
systems that we add:
- Three new Rockchips rk3399 based boards:
- FriendlyElec NanoPC-T4 and NanoPi M4
- Radxa ROCK Pi 4
- Five new i.MX6 family SoM modules and boards for industrial
products:
- Logic PD i.MX6QD SoM and evaluation baseboad
- Y Soft IOTA Draco/Hydra/Ursa family boards based on i.MX6DL
- Phytec phyCORE i.MX6 UltraLite SoM and evaluation module
- MYIR Tech MYD-LPC4357 development based on the NXP lpc4357
microcontroller
- Chameleon96, an Intel/Altera Cyclone5 based FPGA development system
in 96boards form factor
- Arm Fixed Virtual Platforms(FVP) Base RevC, a purely virtual
platform for corresponding to the latest "fast model"
- Another Raspberry Pi variant: Model 3 A+, supported both in 32-bit
and 64-bit mode.
- Oxalis Evalkit V100 based on NXP Layerscape LS1012a, in 96Boards
enterprise form factor
- Elgin RV1108 R1 development board based on 32-bit Rockchips RV1108
For already supported boards and SoCs, we often add support for new
devices after merging the drivers. This time, the largest changes
include updates for
- STMicroelectronics stm32mp1, which was now formally launched last
week
- Qualcomm Snapdragon 845, a high-end phone and low-end laptop chip
- Action Semi S700
- TI AM654x, their recently merged 64-bit SoC from the OMAP family
- Various Amlogic Meson SoCs
- Mediatek MT2712
- NVIDIA Tegra186 and Tegra210
- The ancient NXP lpc32xx family
- Samsung s5pv210, used in some older mobile phones
Many other chips see smaller updates and bugfixes beyond that"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (506 commits)
ARM: dts: exynos: Fix max voltage for buck8 regulator on Odroid XU3/XU4
dt-bindings: net: ti: deprecate cpsw-phy-sel bindings
ARM: dts: am335x: switch to use phy-gmii-sel
ARM: dts: am4372: switch to use phy-gmii-sel
ARM: dts: dm814x: switch to use phy-gmii-sel
ARM: dts: dra7: switch to use phy-gmii-sel
arch: arm: dts: kirkwood-rd88f6281: Remove disabled marvell,dsa reference
ARM: dts: exynos: Add support for secondary DAI to Odroid XU4
ARM: dts: exynos: Add support for secondary DAI to Odroid XU3
ARM: dts: exynos: Disable ARM PMU on Odroid XU3-lite
ARM: dts: exynos: Add stdout path property to Arndale board
ARM: dts: exynos: Add minimal clkout parameters to Exynos3250 PMU
ARM: dts: exynos: Enable ADC on Odroid HC1
arm64: dts: sprd: Remove wildcard compatible string
arm64: dts: sprd: Add SC27XX fuel gauge device
arm64: dts: sprd: Add SC2731 charger device
arm64: dts: sprd: Add ADC calibration support
arm64: dts: sprd: Remove PMIC INTC irq trigger type
arm64: dts: rockchip: Enable tsadc device on rock960
ARM: dts: rockchip: add chosen node on veyron devices
...
The LS1028A RDB board features an Atheros PHY connected over
SGMII to the ENETC PF0 (or Port0). ENETC Port1 (PF1) has no
external connection on this board, so it can be disabled for now.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LS1028A SoC features a PCI Integrated Endpoint Root Complex
(IERC) defining several integrated PCI devices, including the ENETC
ethernet controller integrated endpoints (IEPs). The IERC implements
ECAM (Enhanced Configuration Access Mechanism) to provide access
to the PCIe config space of the IEPs. This means the the IEPs
(including ENETC) do not support the standard PCIe BARs, instead
the Enhanced Allocation (EA) capability structures in the ECAM space
are used to fix the base addresses in the system, and the PCI
subsystem uses these structures for device enumeration and discovery.
The "ranges" entries contain basic information from these EA capabily
structures required by the kernel for device enumeration.
The current patch also enables the first 2 ENETC PFs (Physiscal
Functions) and the associated VFs (Virtual Functions), 2 VFs for
each PF. Each of these ENETC PFs has an external ethernet port
on the LS1028A SoC.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the PCIE EP node in dts for ls1046a.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <minghuan.lian@nxp.com>
Reviewed-by: Zhiqiang Hou <zhiqiang.hou@nxp.com>
Reviewed-by: Rob Herring <robh+dt@kernel.org>
The peripheral bus on the i.MX8MQ is still limited to 32bits, so
we need to declare the usable range for device DMA operations, as
the DRAM will extend across the 32bit boundary if more than 3GB
are installed.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add RTC support for i.MX8MQ.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Chris Spencer <christopher.spencer@sea.co.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
