When xhci_mem_cleanup() is called, we can't be sure if the xHC is
actually halted. We can ask the xHC to halt by writing to the RUN bit
in the command register, but that might timeout due to a HW hang.
If the host controller is still running, we should not write zeroed
values to the event ring dequeue pointers or base tables, the DCBAA
pointers, or the command ring pointers. Eric Fu reports his VIA VL800
host accesses the event ring pointers after a failed register restore on
resume from suspend. The hypothesis is that the host never actually
halted before the register write to change the event ring pointer to
zero.
Remove all writes of zeroed values to pointer registers in
xhci_mem_cleanup(). Instead, make all callers of the function reset the
host controller first, which will reset those registers to zero.
xhci_mem_init() is the only caller that doesn't first halt and reset the
host controller before calling xhci_mem_cleanup().
This should be backported to kernels as old as 2.6.32.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Elric Fu <elricfu1@gmail.com>
Cc: stable@vger.kernel.org
Eric Fu reports a problem with his VIA host controller fetching a zeroed
event ring pointer on resume from suspend. The host should have been
halted, but we can't be sure because that code ignores the return value
from xhci_halt(). Print a warning when the host controller refuses to
halt within XHCI_MAX_HALT_USEC (currently 16 seconds).
(Update: it turns out that the VIA host controller is reporting a halted
state when it fetches the zeroed event ring pointer. However, we still
need this warning for other host controllers.)
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
While we're at that, define IMAN bitfield to aid readability.
The interrupt enable bit should be set once on driver init, and we
shouldn't need to continually re-enable it. Commit c21599a3 introduced
a read of the irq_pending register, and that allows us to preserve the
state of the IE bit. Before that commit, we were blindly writing 0x3 to
the register.
This patch should be backported to kernels as old as 2.6.36, or ones
that contain the commit c21599a361 "USB:
xhci: Reduce reads and writes of interrupter registers".
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
keyctl_session_to_parent(task) sets ->replacement_session_keyring,
it should be processed and cleared by key_replace_session_keyring().
However, this task can fork before it notices TIF_NOTIFY_RESUME and
the new child gets the bogus ->replacement_session_keyring copied by
dup_task_struct(). This is obviously wrong and, if nothing else, this
leads to put_cred(already_freed_cred).
change copy_creds() to clear this member. If copy_process() fails
before this point the wrong ->replacement_session_keyring doesn't
matter, exit_creds() won't be called.
Cc: <stable@vger.kernel.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Running 'perf kvm --host --guest --guestmount /tmp/guestmount record -a -g -- sleep 2'
Was resulting in a segfault. For event type PERF_RECORD_MMAP,
event->ip.pid is being used in perf_session__find_machine_for_cpumode,
which is not correct.
The event->ip.pid field happens to be 0 in this case and results in
returning a NULL machine object. Finally, access to self->pid in
machine__mmap_name, results in a segfault later.
For PERF_RECORD_MMAP type, pass event->mmap.pid.
Signed-off-by: Nikunj A. Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Nikunj A. Dadhania <nikunj@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20120409081835.10576.22018.stgit@abhimanyu.in.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Marc Merlin reported many order-1 allocations failures in TX path on its
wireless setup, that dont make any sense with MTU=1500 network, and non
SG capable hardware.
After investigation, it turns out TCP uses sk_stream_alloc_skb() and
used as a convention skb_tailroom(skb) to know how many bytes of data
payload could be put in this skb (for non SG capable devices)
Note : these skb used kmalloc-4096 (MTU=1500 + MAX_HEADER +
sizeof(struct skb_shared_info) being above 2048)
Later, mac80211 layer need to add some bytes at the tail of skb
(IEEE80211_ENCRYPT_TAILROOM = 18 bytes) and since no more tailroom is
available has to call pskb_expand_head() and request order-1
allocations.
This patch changes sk_stream_alloc_skb() so that only
sk->sk_prot->max_header bytes of headroom are reserved, and use a new
skb field, avail_size to hold the data payload limit.
This way, order-0 allocations done by TCP stack can leave more than 2 KB
of tailroom and no more allocation is performed in mac80211 layer (or
any layer needing some tailroom)
avail_size is unioned with mark/dropcount, since mark will be set later
in IP stack for output packets. Therefore, skb size is unchanged.
Reported-by: Marc MERLIN <marc@merlins.org>
Tested-by: Marc MERLIN <marc@merlins.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Merlin reported many order-1 allocations failures in TX path on its
wireless setup, that dont make any sense with MTU=1500 network, and non
SG capable hardware.
Turns out part of the problem comes from pskb_expand_head() not using
ksize() to get exact head size given by kmalloc(). Doing the same thing
than __alloc_skb() allows more tailroom in skb and can prevent future
reallocations.
As a bonus, struct skb_shared_info becomes cache line aligned.
Reported-by: Marc MERLIN <marc@merlins.org>
Tested-by: Marc MERLIN <marc@merlins.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it stands the bridge IGMP snooping system will respond to
group leave messages with queries for remaining membership.
This is both unnecessary and undesirable. First of all any
multicast routers present should be doing this rather than us.
What's more the queries that we send may end up upsetting other
multicast snooping swithces in the system that are buggy.
In fact, we can simply remove the code that send these queries
because the existing membership expiry mechanism doesn't rely
on them anyway.
So this patch simply removes all code associated with group
queries in response to group leave messages.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there are still many Acer models that might not be covered by
the current fixup table, let's add back a few typical model names so
that user can test the fixup without recompiling.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/soc/codecs/wm9705.c: In function 'ac97_prepare':
sound/soc/codecs/wm9705.c:251: error: 'runtime' undeclared (first use in this function)
This was caused by commit e6968a (ASoC: codecs: Remove rtd->codec usage from CODEC drivers),
which removed the 'struct snd_pcm_runtime *runtime = substream->runtime' definition.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the following build error:
sound/soc/codecs/ac97.c: In function 'ac97_prepare':
sound/soc/codecs/ac97.c:33: error: 'runtime' undeclared (first use in this function)
This was caused by commit e6968a (ASoC: codecs: Remove rtd->codec usage from CODEC drivers),
which removed the 'struct snd_pcm_runtime *runtime = substream->runtime' definition.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to an internal workaround master list, we need to set bit 5
of register 9400 to avoid issues with color blits.
Testing shows that this seems to fix the blitter hangs when fbc is
enabled on snb, thanks to Chris Wilson for figuring this out.
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Michael "brot" Groh <michael.groh@minad.de>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The 845g shares the errata with i830 whereby executing a command
within 2 cachelines of the end of the ringbuffer may cause a GPU hang.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix build warnings by providing a struct stub since no fields of
the struct are used:
include/linux/vgaarb.h:66:9: warning: 'struct pci_dev' declared inside parameter list
include/linux/vgaarb.h:66:9: warning: its scope is only this definition or declaration, which is probably not what you want
include/linux/vgaarb.h:99:34: warning: 'struct pci_dev' declared inside parameter list
include/linux/vgaarb.h:109:6: warning: 'struct pci_dev' declared inside parameter list
include/linux/vgaarb.h:121:8: warning: 'struct pci_dev' declared inside parameter list
include/linux/vgaarb.h:140:37: warning: 'struct pci_dev' declared inside parameter list
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch fixes the irq_domain_mapping debugfs output to pad pointer
values with leading zeros so that pointer values are displayed
correctly. Otherwise you get output similar to "0x 5e0000000000000".
Also, when the irq_domain is set to 'null'
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: David Daney <david.daney@cavium.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
The actual name of the irq_domain mapping debugfs file is
"irq_domain_mapping" not "virq_mapping".
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It makes no sense to export this trivial function. Make it a static inline
instead.
This patch also drops virq_to_hw from arch/c6x since it is unused by that
architecture.
v2: Move irq_hw_number_t into types.h to fix ARM build failure
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In commit 4bbdd45a (irq_domain/powerpc: eliminate irq_map; use
irq_alloc_desc() instead) code was added that ignores error returns
from irq_alloc_desc_from() by (silently) casting the return value to
unsigned. The negitive value error return now suddenly looks like a
valid irq number.
Commits cc79ca69 (irq_domain: Move irq_domain code from powerpc to
kernel/irq) and 1bc04f2c (irq_domain: Add support for base irq and
hwirq in legacy mappings) move this code to its current location in
irqdomain.c
The result of all of this is a null pointer dereference OOPS if one of
the error cases is hit.
The fix: Don't cast away the negativeness of the return value and then
check for errors.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
[grant.likely: dropped addition of new 'irq' variable]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When no platform_data is present and either 'spi-num-chipselects' is
not defined in the DT or 'cs-gpios' has less entries than
'spi-num-chipselects' specifies, the NULL platform_data pointer is
being dereferenced.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fixes the following warning when "SAMSUNG EXYNOS5" is not selected:
warning: ‘exynos5_gpios_1’ defined but not used [-Wunused-variable]
warning: ‘exynos5_gpios_2’ defined but not used [-Wunused-variable]
warning: ‘exynos5_gpios_3’ defined but not used [-Wunused-variable]
warning: ‘exynos5_gpios_4’ defined but not used [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Commit fe1952fc0a
"powerpc: Rework runlatch code" has a nasty typo
where it uses "TLF_RUNLATCH" instead of "_TLF_RUNLATCH"
(bit number instead of bit mask), causing some flags to
be potentially lost such as _TLF_RESTORE_SIGMASK
(Brown paper bag for me ! We should be able to make
that break at compile time with a bit of magic, any
volunteer ?)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This fixes builds where CONFIG_AUDIT is not defined and
CONFIG_SECURITY_SMACK=y.
This got introduced by the stack-usage reducation commit 48c62af68a
("LSM: shrink the common_audit_data data union").
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1/ regression fix for Xen as it now trips over a broken assumption
about the dma address size on 32-bit builds
2/ new quirk for netdma to ignore dma channels that cannot meet
netdma alignment requirements
3/ fixes for two long standing issues in ioatdma (ring size overflow)
and iop-adma (potential stack corruption)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=F3IR
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine fixes from Dan Williams:
1/ regression fix for Xen as it now trips over a broken assumption
about the dma address size on 32-bit builds
2/ new quirk for netdma to ignore dma channels that cannot meet
netdma alignment requirements
3/ fixes for two long standing issues in ioatdma (ring size overflow)
and iop-adma (potential stack corruption)
* tag 'dmaengine-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
netdma: adding alignment check for NETDMA ops
ioatdma: DMA copy alignment needed to address IOAT DMA silicon errata
ioat: ring size variables need to be 32bit to avoid overflow
iop-adma: Corrected array overflow in RAID6 Xscale(R) test.
ioat: fix size of 'completion' for Xen
xhci_unregister_pci() is called in xhci_hcd_init().
Signed-off-by: Gerard Snitselaar <dev@snitselaar.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
1/ convert open-coded KERN_ERR+dump_stack() to WARN(), so that automated
tools pick up this warning.
2/ include the 'child' and 'parent' kobject names. This information was
useful for tracking down the case where scsi invoked device_del() on a
parent object and subsequently invoked device_add() on a child. Now the
warning looks like:
kobject_add_internal failed for target8:0:16 (error: -2 parent: end_device-8:0:24)
Pid: 2942, comm: scsi_scan_8 Not tainted 3.3.0-rc7-isci+ #2
Call Trace:
[<ffffffff8125e551>] kobject_add_internal+0x1c1/0x1f3
[<ffffffff81075149>] ? trace_hardirqs_on+0xd/0xf
[<ffffffff8125e659>] kobject_add_varg+0x41/0x50
[<ffffffff8125e723>] kobject_add+0x64/0x66
[<ffffffff8131124b>] device_add+0x12d/0x63a
[<ffffffff8125e0ef>] ? kobject_put+0x4c/0x50
[<ffffffff8132f370>] scsi_sysfs_add_sdev+0x4e/0x28a
[<ffffffff8132dce3>] do_scan_async+0x9c/0x145
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: James Bottomley <JBottomley@parallels.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In scsi at least two cases of the parent device being deleted before the
child is added have been observed.
1/ scsi is performing async scans and the device is removed prior to the
async can thread running (can happen with an in-opportune / unlikely
unplug during initial scan).
2/ libsas discovery event running after the parent port has been torn
down (this is a bug in libsas).
Result in crash signatures like:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000098
IP: [<ffffffff8115e100>] sysfs_create_dir+0x32/0xb6
...
Process scsi_scan_8 (pid: 5417, threadinfo ffff88080bd16000, task ffff880801b8a0b0)
Stack:
00000000fffffffe ffff880813470628 ffff88080bd17cd0 ffff88080614b7e8
ffff88080b45c108 00000000fffffffe ffff88080bd17d20 ffffffff8125e4a8
ffff88080bd17cf0 ffffffff81075149 ffff88080bd17d30 ffff88080614b7e8
Call Trace:
[<ffffffff8125e4a8>] kobject_add_internal+0x120/0x1e3
[<ffffffff81075149>] ? trace_hardirqs_on+0xd/0xf
[<ffffffff8125e641>] kobject_add_varg+0x41/0x50
[<ffffffff8125e70b>] kobject_add+0x64/0x66
[<ffffffff8131122b>] device_add+0x12d/0x63a
In this scenario the parent is still valid (because we have a
reference), but it has been device_del()'d which means its kobj->sd
pointer is NULL'd via:
device_del()->kobject_del()->sysfs_remove_dir()
...and then sysfs_create_dir() (without this fix) goes ahead and
de-references parent_sd via sysfs_ns_type():
return (sd->s_flags & SYSFS_NS_TYPE_MASK) >> SYSFS_NS_TYPE_SHIFT;
This scenario is being fixed in scsi/libsas, but if other subsystems
present the same ordering the system need not immediately crash.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: James Bottomley <JBottomley@parallels.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following build error:
sound/soc/codecs/wm9712.c:482:32: error: 'runtime' undeclared (first use in this function)
sound/soc/codecs/wm9712.c:499:33: error: 'runtime' undeclared (first use in this function)
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Recent list discussions concluded that drivers should not be calling
of_have_populated_dt(), and hence of_have_populated_dt() should not be
exported. Use a different mechanism to detect DT vs. non-DT boot.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
of_gpio_simple_xlate() has an off-by-one bug where it checks to see if
args[0] is > ngpio instead of >=. args[0] must always be less than
ngpio because it is a zero-based enumeration.
Signed-off-by: Roland Stigge <stigge@antcom.de>
[grant.likely: beef up commit text]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The variable 'bit' is uninitialized in the first iteration of for
loop. Fix it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The irqdomain api changed significantly in v3.4 which caused a build
failure for this driver.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Hans J. Koch <hjk@linutronix.de>
Cc: Torben Hohn <torbenh@linutronix.de>
Fix a code path in tcp_rcv_rtt_update() that was comparing scaled and
unscaled RTT samples.
The intent in the code was to only use the 'm' measurement if it was a
new minimum. However, since 'm' had not yet been shifted left 3 bits
but 'new_sample' had, this comparison would nearly always succeed,
leading us to erroneously set our receive-side RTT estimate to the 'm'
sample when that sample could be nearly 8x too high to use.
The overall effect is to often cause the receive-side RTT estimate to
be significantly too large (up to 40% too large for brief periods in
my tests).
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c43b874d5d (tcp: properly initialize tcp memory limits) tried
to fix a regression added in commits 4acb4190 & 3dc43e3,
but still get it wrong.
Result is machines with low amount of memory have too small tcp_rmem[2]
value and slow tcp receives : Per socket limit being 1/1024 of memory
instead of 1/128 in old kernels, so rcv window is capped to small
values.
Fix this to match comment and previous behavior.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Glauber Costa <glommer@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit c1afdaff90.
Users have reported connection failures in 3.3.1 and suspend/resume
failures in 3.4-rcX. Revert this commit for now - PS IDLE can be
fixed in a clean manner later on.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move rt2x00rfkill_register(rt2x00dev) to rt2x00lib_probe_dev
function. It fixes of starting rfkill_poll function at the
right time if sets hard rfkill block and reboot. rt2x00mac_rfkill_poll
should be starting before bringing up the wireless interface.
Signed-off-by: Chen, Chien-Chia <machen@suse.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
CC: Kevin Chou <kevin.chou@mediatek.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following is seen during allmodconfig builds for MIPS:
drivers/bcma/driver_pci_host.c:518:2: error: implicit declaration
of function 'pcibios_enable_device' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [drivers/bcma/driver_pci_host.o] Error 1
Most likey introduced by commit 49dc957715
"bcma: add PCIe host controller"
Add the header instead of implicitly assuming it will be present.
Sounds like a good idea, but that alone doesn't fix anything.
The real problem is that the Kconfig has settings related to whether
PCI is possible, i.e.
config BCMA_HOST_PCI_POSSIBLE
bool
depends on BCMA && PCI = y
default y
config BCMA_HOST_PCI
bool "Support for BCMA on PCI-host bus"
depends on BCMA_HOST_PCI_POSSIBLE
...but what is missing is that BCMA_DRIVER_PCI_HOSTMODE doesn't
have any dependencies on the above. Add one.
CC: Hauke Mehrtens <hauke@hauke-m.de>
CC: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull sparc fixes from David Miller:
1) Build fix for LEON, from Sam Ravnborg.
2) Make the sparc side changes that go along with the infrastructure to
retry faults when blocking on a disk transfer. From Kautuk Consul.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc32,leon: fix leon build
sparc/mm/fault_32.c: Port OOM changes to do_sparc_fault
sparc/mm/fault_64.c: Port OOM changes to do_sparc64_fault
This is a trivial rename to stop the build system complaining that we're
referencing things we shouldn't be.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=45TQ
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull a regulator build fix from Mark Brown:
"Fix a build warning in the anatop driver for 3.4
This is a trivial rename to stop the build system complaining that
we're referencing things we shouldn't be."
* tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: anatop: fix 'anatop_regulator' name collision
We've only computed whether we need to fall back to 6bpc due to dp
link bandwidth constrains in mode_valid, but not mode_fixup. Under
various circumstances X likes to create new modes which then lack
proper 6bpc flags (if required), resulting in mode_fixup failures and
ultimately black screens.
Chris Wilson pointed out that we still get things wrong for bpp > 24,
but that should be fixed in another patch (and it'll be easier because
this patch consolidates the logic).
The likely culprit for this regression is
commit 3d794f87238f74d80e78a7611c7fbde8a54c85c2
Author: Keith Packard <keithp@keithp.com>
Date: Wed Jan 25 08:16:25 2012 -0800
drm/i915: Force explicit bpp selection for intel_dp_link_required
v2: Fix indentation and tune down the too bold claim that this should
fix the world. Both noticed by Chris Wilson.
v3: Try to really git add things.
Reported-and-tested-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48170
Cc: stable@kernel.org
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Image on Z11m cards was totally garbled due to wrong memory being
selected. Add a special handling for Z11m cards. Tested on PCIe Z11 and
Z11m cards.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If gpio_request fails, we need to free all allocated resources.
Current code uses wrong array index to access gpio_data array.
So current code actually frees gpio_data[i].gpio by j times.
This patch moves the error handling code to err_out and thus improves
readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
m68k doesn't have memblock_reserve, which causes a build failure
with allmodconfig. Make PERSISTENT_RAM and RAM_CONSOLE depend on
HAVE_MEMBLOCK.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c client data set is of type struct indio_dev pointer and hence the
pointer returned from i2c_get_clientdata() should be assigned to
an object of type struct indio_dev and not to an object of type
struct ak8975_data.
Also in ak8975_probe() client data should be set first
before calling ak8975_setup() as it references the client data.
Signed-off-by: Preetham Chandru R <pchandru@nvidia.com>
CC: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
