Move the mmc nodes above the ohci nodes for proper ordering by name.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sunxi-common-regulators.dtsi provided dummy regulators vcc3v0, vcc3v3,
vcc5v0. 3.0V/3.3V and 5.0V are commonly used voltages in Allwinner
devices. These dummy regulators provide a stand-in when bindings that
require one, but the real regulator is not supported yet.
Since these are no longer needed, we can drop the include file by
copying over reg_usb1_vbus.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AXP809 PMIC is the primary PMIC. It provides various supply voltages
for the SoC and other peripherals. The PMIC's interrupt line is
connected to NMI pin of the SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
i2c3 and uart4 are available on the GPIO header. Though these pins only
have this one special function, the user may choose to use them as GPIOs
instead.
Since our policy is not to choose what function to present on the GPIO
headers of development boards, remove them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
mmc2 has a special pin for eMMC hardware reset, which is controllable
from the controller. Add the "mmc-cap-hw-reset" property to denote that
this controller supports this function, and the pins are actually used.
Also increase the signal drive strength for mmc2 pins, for HS-DDR mode
support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 Optimus board has a consumer IR receiver. Enable it in the DT.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The FSF address triggers a warning on checkpatch, saying that the FSF
license is already present in the Linux source code, and that it has
already changed in the past.
Remove it from our DT, as suggested.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add UART aliases and stdout-path property for all the Allwinner boards so that
we won't have to rely on the bootargs' console= value, while working with
legacy bootloaders.
While we're at it, also remove the mentions of earlyprintk in the bootargs,
that will remove our default bootargs entirely, and allow the kernel to boot on
a system even if DEBUG_LL is configured for another system.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since the phy core already supports specifying a regulator to handle
during power up/down, it was decided to drop the regulator support
in the sun9i usb phy driver.
This patch switches the DT to the core bindings. This and the phy driver
would be in the same release and should not be a problem as far as DT
stability goes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the Optimus board, all three USB hosts can be used.
HCI0 and HCI2 are available through the USB connector.
HCI1 is available with HSIC through 2 pins on the GPIO
expansion header.
This patch also adds a regulator for HCI2/USB3's VBUS.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new platforms
and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of DTS
contents from GPL to GPLv2+/X11 so that the same files can be reused in
other non-GPL projects more easily. There's also been changes to the
DT Makefile to make it a little less conflict-ridden and churny down
the road.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XEw1
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new
platforms and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of
DTS contents from GPL to GPLv2+/X11 so that the same files can be
reused in other non-GPL projects more easily. There's also been
changes to the DT Makefile to make it a little less conflict-ridden
and churny down the road"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (330 commits)
ARM: dts: Add PPMU node for exynos4412-trats2
ARM: dts: Add PPMU node for exynos3250-monk and exynos3250-rinato
ARM: dts: Add PPMU dt node for exynos4 and exynos4210
ARM: dts: Add PPMU dt node for exynos3250
ARM: dts: add mipi dsi device node for exynos4415
ARM: dts: add fimd device node for exynos4415
ARM: dts: Add syscon phandle to the video-phy node for Exynos4
ARM: dts: Add sound nodes for exynos4412-trats2
ARM: dts: Fix CLK_MOUT_CAMn parent clocks assignment for exynos4412-trats2
ARM: dts: Fix CLK_UART_ISP_SCLK clock assignment in exynos4x12.dtsi
ARM: dts: Add max77693 charger node for exynos4412-trats2
ARM: dts: Switch max77686 regulators to GPIO control for exynos4412-trats2
ARM: dts: Add suspend configuration for max77686 regulators for exynos4412-trats2
ARM: dts: Add Maxim 77693 fuel gauge node for exynos4412-trats2
ARM: dts: am57xx-beagle-x15: Fix USB2 mode
ARM: dts: am57xx-beagle-x15: Add extcon nodes for USB
ARM: dts: dra72-evm: Add extcon nodes for USB
ARM: dts: dra7-evm: Add extcon nodes for USB
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
...
Commit f77d55a3b5 ("serial: 8250_dw: get index of serial line from DT
aliases") made the serial driver now use the serial aliases to get the tty
number, pointing out that our aliases have been wrong all along.
Remove them from the DTSI and add custom ones in the relevant boards.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 Optimus Board has a 16GB eMMC connected to mmc2, with 8 bit
wide data bus.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the micro-sd slot on the A80 Optimus Board, which is connected to
mmc0. This adds the card-detect gpio and enables mmc0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The preferred method of referencing nodes from the dtsi is to use
labels, instead of copying the complete tree.
This patch converts sun9i-a80-optimus.dts to use label references.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pinctrl nodes require some extra opaque arguments for the pull up and drive
strength values.
Introduce a new header file and convert the device trees to replace these
opaque numbers by defines.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Replace the various raw GPIO flags by their definition in the common
dt-bindings header.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 Optimus board exposes uart4 on the GPIO expansion header.
Enable it so we can use it.
Also enable the internal pull-ups, as there doesn't seem to be
external pull-up resistors for pins on the expansion header.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 Optimus board has 3 usable LEDs that are controlled via GPIO.
This patch adds support for 2 of them which are driver by GPIOs in the
main pin controller. The remaining one uses GPIO from the R_PIO
controller, which we don't support yet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
i2c3 is exposed on the GPIO extension header. Enable it so we can use it.
Also enable internal pull-ups on the pins, as they don't seem to have
external pull-up resistors.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the UART0 muxing, as set up by the bootloader.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
During the GPL to GPL/X11 licensing migration, the GPL notice introduced
mentionned the device trees as a library, which is not really accurate. It
began to spread by copy and paste. Fix all these library mentions to reflect
the file that it's actually just a file.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 Optimus Board is was launched with the Allwinner A80 SoC.
It was jointly developed by Allwinner and Merrii.
This board has a UART port, a JTAG connector, USB host ports, a USB
3.0 OTG connector, an HDMI output, a micro SD slot, 8G NAND flash,
4G DRAM, a camera sensor interface, a WiFi/BT combo chip, a headphone
jack, IR receiver, and additional GPIO headers.
This patch adds only basic support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Andreas Färber <afaerber@suse.de>
