commit b070f9ca78680486927b799cf6126b128a7c2c1b upstream.
omap_hwmod_get_pwrdm() may access a NULL clk_hw pointer in some failure
cases. Add a check for the case and bail out gracely if this happens.
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 15f68f027ebd961b99a1c420f96ff3838c5e4450 ]
While 7e5f3155dc ("ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2")
fixed the LED0 assignment on the PDK2 board, the same commit did not
update the touchscreen IRQ line assignment, which is the same GPIO line,
shared between the LED0 output and touchscreen IRQ input. To make this
more convoluted, the same EXTI input (not the same GPIO line) is shared
between Button B which is Active-Low IRQ, and touchscreen IRQ which is
Edge-Falling IRQ, which cannot be used at the same time. In case the LCD
board with touchscreen is in use, which is the case here, LED0 must be
disabled, Button B must be polled, so the touchscreen interrupt works as
it should.
Update the touchscreen IRQ line assignment, disable LED0 and use polled
GPIO button driver for Button B, since the DT here describes baseboard
with LCD board.
Fixes: 7e5f3155dc ("ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36862c1ebc92a7e6fcc55002965c44b8ad17d4ca ]
The LAN8710 Energy Detect Power Down (EDPD) functionality might cause
unreliable cable detection. There are multiple accounts of this in the
SMSC PHY driver patches which attempted to make EDPD reliable, however
it seems there is always some sort of corner case left. Unfortunatelly,
there is no errata documented which would confirm this to be a silicon
bug on the LAN87xx series of PHYs (LAN8700, LAN8710, LAN8720 at least).
Disable EDPD on the DHCOM SoM, just like multiple other boards already
do as well, to make the cable detection reliable.
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c68ef4ad180e09805fa46965d15e1dfadf09ffa5 ]
This device tree include file describes a fixed-regulator
connecting smps7_reg output (1.8V) to some 1.8V rail and
consumers (vdds_1v8_main).
This regulator does not physically exist.
I assume it was introduced as a wrapper around smps7_reg
to provide a speaking signal name "vdds_1v8_main" as label.
This fixed-regulator without real function was not an issue
in driver code until
Commit 98e48cd9283d ("regulator: core: resolve supply for boot-on/always-on regulators")
introduced a new check for regulator initialization which
makes Palmas regulator registration fail:
[ 5.407712] ldo1: supplied by vsys_cobra
[ 5.412748] ldo2: supplied by vsys_cobra
[ 5.417603] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator
The reason is that the supply-chain of regulators is too
long and goes from ldo3 through the virtual vdds_1v8_main
regulator and then back to smps7. This adds a cross-dependency
of probing Palmas regulators and the fixed-regulator which
leads to probe deferral by the new check and is no longer
resolved.
Since we do not control what device tree files including this
one reference (either &vdds_1v8_main or &smps7_reg or both)
we keep both labels for smps7 for compatibility.
Fixes: 98e48cd9283d ("regulator: core: resolve supply for boot-on/always-on regulators")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d9e30a52047f2d464efdfd1d561ae1f707a0286 ]
The pinctrl_power_button/pinctrl_power_out each define single GPIO
pinmux, except it is exactly the other one than the matching gpio-keys
and gpio-poweroff DT nodes use for that functionality. Swap the two
GPIOs to correct this error.
Fixes: 50d29fdb76 ("ARM: dts: imx53: Add power GPIOs on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20fb73911fec01f06592de1cdbca00b66602ebd7 ]
The function imx_mmdc_perf_init recently had a 3rd argument added to
it but the equivalent macro was not updated and is still the older
2 argument version. Fix this by adding in the missing 3rd argumement
mmdc_ipg_clk.
Fixes: f07ec8536580 ("ARM: imx: add missing clk_disable_unprepare()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd8e83884fdd7b5fc411f201a58d8d01890198a2 ]
The AR803x PHY used on this modules seems to require the reset line to
be asserted for around 10ms in order to avoid rare cases where the PHY
gets stuck in an incoherent state that prevents it to function
correctly.
The previous value of 2ms was found to be problematic on some setups,
causing intermittent issues where the PHY would be unresponsive
every once in a while on some sytems, with a low occurrence (it typically
took around 30 consecutive reboots to encounter the issue).
Bumping the delay to the 10ms makes the issue dissapear, with more than
2500 consecutive reboots performed without the issue showing-up.
Fixes: 208d7baf80 ("ARM: imx: initial SolidRun HummingBoard support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Hervé Codina <herve.codina@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f07ec85365807b3939f32d0094a6dd5ce065d1b9 ]
clock source is prepared and enabled by clk_prepare_enable()
in probe function, but no disable or unprepare in remove and
error path.
Fixes: 9454a0caff ("ARM: imx: add mmdc ipg clock operation for mmdc")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9613aa07f16d6042e74208d1b40a6104d72964a ]
Commit e76bdfd740 ("ARM: imx: Added perf functionality to mmdc driver")
introduced imx_mmdc_remove(), the mmdc_base need be unmapped in it if
config PERF_EVENTS is enabled.
If imx_mmdc_perf_init() fails, the mmdc_base also need be unmapped.
Fixes: e76bdfd740 ("ARM: imx: Added perf functionality to mmdc driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82a1c67554dff610d6be4e1982c425717b3c6a23 ]
Once the new schema interrupt-controller/arm,vic.yaml is added, we get
the below warnings:
arch/arm/boot/dts/versatile-ab.dt.yaml:
intc@10140000: $nodename:0: 'intc@10140000' does not match
'^interrupt-controller(@[0-9a-f,]+)*$'
arch/arm/boot/dts/versatile-ab.dt.yaml:
intc@10140000: 'clear-mask' does not match any of the regexes
Fix the node names for the interrupt controller to conform
to the standard node name interrupt-controller@.. Also drop invalid
clear-mask property.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210701132118.759454-1-sudeep.holla@arm.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2d6608b57c50c54c3e46649110e8ea5a40959c30 upstream.
The degree values were reversed out from the magic tap values of 7 (in)
and 15 + inversion (out) initially suggested by Aspeed.
With the patch tacoma survives several gigabytes of reads and writes
using dd while without it locks up randomly during the boot process.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210625061017.1149942-1-andrew@aj.id.au
Fixes: 2fc88f92359d ("mmc: sdhci-of-aspeed: Expose clock phase controls")
Fixes: 961216c135 ("ARM: dts: aspeed: Add Rainier system")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca46ad2214473df1a6a9496be17156d65ba89b9f upstream.
Tacoma and Rainier both have a line-names array that is too long:
gpio gpiochip0: gpio-line-names is length 232 but should be at most length 208
This was probably copied from an AST2500 device tree that did have more
GPIOs on the controller.
Fixes: e9b24b55ca ("ARM: dts: aspeed: rainier: Add gpio line names")
Fixes: 2f68e4e7df ("ARM: dts: aspeed: tacoma: Add gpio line names")
Link: https://lore.kernel.org/r/20210624090742.56640-1-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 093a474ce10d8ea3db3ef2922aca5a38f34bab1b ]
If the PM related modules are not loaded and PM firmware not configured,
the system suspend fails to resume. Let's fix this by adding initial
platform_suspend_ops to block suspend and warn about missing modules.
When pm33xx and wkup_m3_ipc have been loaded and m3 coprocessor booted
with it's firmware, pm33xx sets up working platform_suspend_ops. Note
that we need to configure at least PM_SUSPEND_STANDBY to have
suspend_set_ops().
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bf4abe19089245b7b12f35e5cafb5477b3e2c48 ]
On some STM32 MP15 boards, stpmic node is not correct which generates
warnings running "make dtbs_check W=1" command. Issues are:
-"regulator-active-discharge" is not a boolean but an uint32.
-"regulator-over-current-protection" is not a valid entry for vref_ddr.
-LDO4 has a fixed voltage (3v3) so min/max entries are not allowed.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5247a50c8b53ca214a488da648e1bb35c35c2597 ]
Fix the following dtbs_check warning:
touchscreen@38: 'linux,wakeup' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: kernel@dh-electronics.com
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f493162319788802b6a49634f7268e691b4c10ec ]
The Seeed SoM-STM32MP157C device tree had the eMMC’s (SDMMC2) VQMMC
supply set to v3v3 (buck4), the same as the VMMC supply. That was
incorrect, as on the SoM, the VQMMC supply is provided from vdd (buck3)
instead.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f07edc41220b14ce057a4e6d7161b30688ddb8a2 ]
A test with rockchip-io-domain.yaml gives notifications
for supply properties in io-domains nodes.
Fix them all into ".*-supply$" format.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210606181632.13371-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f30dacf37bc93308e91e4d0fc94681ca73f0f91 ]
Fix the node names for the GPIO LEDs to conform to the standard node
name led-..
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1622981777-5023-6-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f230c32349eb0a43a012a81c08a7f13859b86cbb ]
Fix the node names for the MMC/SD card controller to conform
to the standard node name mmc@..
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1622981777-5023-2-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf24b91f4baf7e421c770a1d9c7d381b10206ac9 ]
Fix following warning observed with "make dtbs_check W=1" command.
It concerns f429 eval and disco boards, f769 disco board.
Warning (unit_address_vs_reg): /gpio_keys/button@0: node has a unit name,
but no reg or ranges property
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0171b07373cc8c2815ca5fa79a7308fdefa54ca4 ]
The microSD card detect pin is physically connected to the MPU pin PI3.
The Device Tree configuration of the card detect pin was wrong—it was
set to pin PB7 instead. If such configuration was used, the kernel would
hang on “Waiting for root device” when booting from a microSD card.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4dd6066bc304649e3159f1c7a08ece25d537e00 ]
The 3v3 regulator GPIO is GP6 and not GP7, which is the DDR regulator.
Both regulators are always-on, nevertheless the DT model needs to be
corrected, fix it.
Reported-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f45da704de425d74abd75feaa928fc8a3df03ba ]
All Tegra boards which use WM8903 audio codec are specifying a wrong
polarity for the headphones detection GPIO. The kernel driver hardcodes
the polarity to active-low, which is the correct polarity, so we can fix
the device-trees safely.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e7f5ee1137397def6580461e27e5efcb68183ee ]
A number of sub-mailbox node names in various OMAP2+ dts files are
currently using underscores. This is not adhering to the node name
convention, fix all of these to use hiphens.
These nodes are already using the prefix mbox, so they will be in
compliance with the sub-mailbox node name convention being added in
the OMAP Mailbox YAML binding as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7d30b8fcd111e9feb171023c0e0c8d855582dcb ]
The ti,no-reset-on-init flag need to be at the interconnect target module
level for the modules that have it defined.
The ti-sysc driver handles this case, but produces warning, not a critical
issue.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2566d5b8c1670f7d7a44cc1426d254147ec5c421 ]
The ti,no-reset-on-init flag need to be at the interconnect target module
level for the modules that have it defined.
The ti-sysc driver handles this case, but produces warning, not a critical
issue.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b644c5e01c870056e13a096e14b9a92075c8f682 ]
The ti,no-reset-on-init flag need to be at the interconnect target module
level for the modules that have it defined.
The ti-sysc driver handles this case, but produces warning, not a critical
issue.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 723de6a4126b2474a8106e943749e1554012dad6 ]
Without SoC specific PHY fixups the network interface on this board will
fail to work. Provide missing DT properties to make it work again.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4beba4011995a2c44ee27e1d358dc32e6b9211b3 ]
This adds a mounting matrix to the accelerometer
on the TVK1281618 R3.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4917b702818872fdf2a9973705af3aa7d3d1f19e ]
Rename the AB8500 gpio controller node from ab8500-gpio to
ab8500-gpiocontroller, since -gpio is a common suffix for
gpio consumers.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89b759469d525f4d5f9c29cd3b1f490311c67f85 ]
The name of the struct, as defined in arch/arm/mach-imx/pm-imx5.c,
is imx5_cpu_suspend_info.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14cdc1f243d79e0b46be150502b7dba9c5a6bdfd ]
Serial interface uart3 on phyFLEX board is capable of 5-wire connection
including signals RTS and CTS for hardware flow control.
Fix signals UART3_CTS_B and UART3_RTS_B padmux assignments and add
missing property "uart-has-rtscts" to allow serial interface to be
configured and used with the hardware flow control.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 970cdc53cb1afa73602028c103dbfb6a230080be ]
Use more generic names (as recommended in the device tree specification
or the binding documentation)
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-4-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3bcbcd396175ac26aa54919c0b31c7d2878fc24 ]
Use more generic names (as recommended in the device tree specification
or the binding documentation)
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
