Now each stream sched ops is defined in different .c file and
added into the global ops in another .c file, it uses extern
to make this work.
However extern is not good coding style to get them in and
even make C=2 reports errors for this.
This patch adds sctp_sched_ops_xxx_init for each stream sched
ops in their .c file, then get them into the global ops by
calling them when initializing sctp module.
Fixes: 637784ade2 ("sctp: introduce priority based stream scheduler")
Fixes: ac1ed8b82c ("sctp: introduce round robin stream scheduler")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-sctp@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_scope_t, and
replace with enum sctp_scope in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_ipv4addr_param_t, and replace
with struct sctp_ipv4addr_param in the places where it's using this
typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lockdep issues a circular dependency warning when AFS issues an operation
through AF_RXRPC from a context in which the VFS/VM holds the mmap_sem.
The theory lockdep comes up with is as follows:
(1) If the pagefault handler decides it needs to read pages from AFS, it
calls AFS with mmap_sem held and AFS begins an AF_RXRPC call, but
creating a call requires the socket lock:
mmap_sem must be taken before sk_lock-AF_RXRPC
(2) afs_open_socket() opens an AF_RXRPC socket and binds it. rxrpc_bind()
binds the underlying UDP socket whilst holding its socket lock.
inet_bind() takes its own socket lock:
sk_lock-AF_RXRPC must be taken before sk_lock-AF_INET
(3) Reading from a TCP socket into a userspace buffer might cause a fault
and thus cause the kernel to take the mmap_sem, but the TCP socket is
locked whilst doing this:
sk_lock-AF_INET must be taken before mmap_sem
However, lockdep's theory is wrong in this instance because it deals only
with lock classes and not individual locks. The AF_INET lock in (2) isn't
really equivalent to the AF_INET lock in (3) as the former deals with a
socket entirely internal to the kernel that never sees userspace. This is
a limitation in the design of lockdep.
Fix the general case by:
(1) Double up all the locking keys used in sockets so that one set are
used if the socket is created by userspace and the other set is used
if the socket is created by the kernel.
(2) Store the kern parameter passed to sk_alloc() in a variable in the
sock struct (sk_kern_sock). This informs sock_lock_init(),
sock_init_data() and sk_clone_lock() as to the lock keys to be used.
Note that the child created by sk_clone_lock() inherits the parent's
kern setting.
(3) Add a 'kern' parameter to ->accept() that is analogous to the one
passed in to ->create() that distinguishes whether kernel_accept() or
sys_accept4() was the caller and can be passed to sk_alloc().
Note that a lot of accept functions merely dequeue an already
allocated socket. I haven't touched these as the new socket already
exists before we get the parameter.
Note also that there are a couple of places where I've made the accepted
socket unconditionally kernel-based:
irda_accept()
rds_rcp_accept_one()
tcp_accept_from_sock()
because they follow a sock_create_kern() and accept off of that.
Whilst creating this, I noticed that lustre and ocfs don't create sockets
through sock_create_kern() and thus they aren't marked as for-kernel,
though they appear to be internal. I wonder if these should do that so
that they use the new set of lock keys.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b8607805dd ("sctp: not copying duplicate addrs to the assoc's
bind address list") tried to check for duplicate address before copying
to asoc's bind_addr list from global addr list.
But all the addrs' sin_ports in global addr list are 0 while the addrs'
sin_ports are bp->port in asoc's bind_addr list. It means even if it's
a duplicate address, af->cmp_addr will still return 0 as the their
sin_ports are different.
This patch is to fix it by setting the sin_port for addr param with
bp->port before comparing the addrs.
Fixes: b8607805dd ("sctp: not copying duplicate addrs to the assoc's bind address list")
Reported-by: Wei Chen <weichen@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add reconf_enable field in all of asoc ep and netns
to indicate if they support stream reset.
When initializing, asoc reconf_enable get the default value from ep
reconf_enable which is from netns netns reconf_enable by default.
It is also to add reconf_capable in asoc peer part to know if peer
supports reconf_enable, the value is set if ext params have reconf
chunk support when processing init chunk, just as rfc6525 section
5.1.1 demands.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp.local_addr_list is a global address list that is supposed to include
all the local addresses. sctp updates this list according to NETDEV_UP/
NETDEV_DOWN notifications.
However, if multiple NICs have the same address, the global list would
have duplicate addresses. Even if for one NIC, promote secondaries in
__inet_del_ifa can also lead to accumulating duplicate addresses.
When sctp binds address 'ANY' and creates a connection, it copies all
the addresses from global list into asoc's bind addr list, which makes
sctp pack the duplicate addresses into INIT/INIT_ACK packets.
This patch is to filter the duplicate addresses when copying the addrs
from global list in sctp_copy_local_addr_list and unpacking addr_param
from cookie in sctp_raw_to_bind_addrs to asoc's bind addr list.
Note that we can't filter the duplicate addrs when global address list
gets updated, As NETDEV_DOWN event may remove an addr that still exists
in another NIC.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to reduce indent level by using continue when the addr
is not allowed, and also drop end_copy by using break.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 486bdee013 ("sctp: add support for RPS and RFS")
saves skb->hash into sk->sk_rxhash so that the inet_* can
record it to flow table.
But sctp uses sock_common_recvmsg as .recvmsg instead
of inet_recvmsg, sock_common_recvmsg doesn't invoke
sock_rps_record_flow to record the flow. It may cause
that the receiver has no chances to record the flow if
it doesn't send msg or poll the socket.
So this patch fixes it by using inet_recvmsg as .recvmsg
in sctp.
Fixes: 486bdee013 ("sctp: add support for RPS and RFS")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP will try to access original IP headers on sctp_recvmsg in order to
copy the addresses used. There are also other places that do similar access
to IP or even SCTP headers. But after 90017accff ("sctp: Add GSO
support") they aren't always there because they are only present in the
header skb.
SCTP handles the queueing of incoming data by cloning the incoming skb
and limiting to only the relevant payload. This clone has its cb updated
to something different and it's then queued on socket rx queue. Thus we
need to fix this in two moments.
For rx path, not related to socket queue yet, this patch uses a
partially copied sctp_input_cb to such GSO frags. This restores the
ability to access the headers for this part of the code.
Regarding the socket rx queue, it removes iif member from sctp_event and
also add a chunk pointer on it.
With these changes we're always able to reach the headers again.
The biggest change here is that now the sctp_chunk struct and the
original skb are only freed after the application consumed the buffer.
Note however that the original payload was already like this due to the
skb cloning.
For iif, SCTP's IPv4 code doesn't use it, so no change is necessary.
IPv6 now can fetch it directly from original's IPv6 CB as the original
skb is still accessible.
In the future we probably can simplify sctp_v*_skb_iif() stuff, as
sctp_v4_skb_iif() was called but it's return value not used, and now
it's not even called, but such cleanup is out of scope for this change.
Fixes: 90017accff ("sctp: Add GSO support")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP has this pecualiarity that its packets cannot be just segmented to
(P)MTU. Its chunks must be contained in IP segments, padding respected.
So we can't just generate a big skb, set gso_size to the fragmentation
point and deliver it to IP layer.
This patch takes a different approach. SCTP will now build a skb as it
would be if it was received using GRO. That is, there will be a cover
skb with protocol headers and children ones containing the actual
segments, already segmented to a way that respects SCTP RFCs.
With that, we can tell skb_segment() to just split based on frag_list,
trusting its sizes are already in accordance.
This way SCTP can benefit from GSO and instead of passing several
packets through the stack, it can pass a single large packet.
v2:
- Added support for receiving GSO frames, as requested by Dave Miller.
- Clear skb->cb if packet is GSO (otherwise it's not used by SCTP)
- Added heuristics similar to what we have in TCP for not generating
single GSO packets that fills cwnd.
v3:
- consider sctphdr size in skb_gso_transport_seglen()
- rebased due to 5c7cdf339a ("gso: Remove arbitrary checks for
unsupported GSO")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry reported that sctp_add_bind_addr may read more bytes than
expected in case the parameter is a IPv4 addr supplied by the user
through calls such as sctp_bindx_add(), because it always copies
sizeof(union sctp_addr) while the buffer may be just a struct
sockaddr_in, which is smaller.
This patch then fixes it by limiting the memcpy to the min between the
union size and a (new parameter) provided addr size. Where possible this
parameter still is the size of that union, except for reading from
user-provided buffers, which then it accounts for protocol type.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Vyukov noted recently that the sctp_port_hashtable had an error in
its size computation, observing that the current method never guaranteed
that the hashsize (measured in number of entries) would be a power of two,
which the input hash function for that table requires. The root cause of
the problem is that two values need to be computed (one, the allocation
order of the storage requries, as passed to __get_free_pages, and two the
number of entries for the hash table). Both need to be ^2, but for
different reasons, and the existing code is simply computing one order
value, and using it as the basis for both, which is wrong (i.e. it assumes
that ((1<<order)*PAGE_SIZE)/sizeof(bucket) is still ^2 when its not).
To fix this, we change the logic slightly. We start by computing a goal
allocation order (which is limited by the maximum size hash table we want
to support. Then we attempt to allocate that size table, decreasing the
order until a successful allocation is made. Then, with the resultant
successful order we compute the number of buckets that hash table supports,
which we then round down to the nearest power of two, giving us the number
of entries the table actually supports.
I've tested this locally here, using non-debug and spinlock-debug kernels,
and the number of entries in the hashtable consistently work out to be
powers of two in all cases.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
CC: Dmitry Vyukov <dvyukov@google.com>
CC: Vladislav Yasevich <vyasevich@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
transport hashtable will replace the association hashtable,
so association hashtable is not used in sctp any more, so
drop the codes about that.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
apply lookup apis to two functions, for __sctp_endpoint_lookup_assoc
and __sctp_lookup_association, it's invoked in the protection of sock
lock, it will be safe, but sctp_lookup_association need to call
rcu_read_lock() and to detect the t->dead to protect it.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we all know, the value of pf_retrans >= max_retrans_path can
disable pf state. The variables of pf_retrans and max_retrans_path
can be changed by the userspace application.
Sometimes the user expects to disable pf state while the 2
variables are changed to enable pf state. So it is necessary to
introduce a new variable to disable pf state.
According to the suggestions from Vlad Yasevich, extra1 and extra2
are removed. The initialization of pf_enable is added.
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Zhu Yanjun <zyjzyj2000@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
modules init functions being called from process context, we better
use GFP_KERNEL allocations to increase our chances to get these
high-order pages we want for SCTP hash tables.
This mostly matters if SCTP module is loaded once memory got fragmented.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider sctp module is unloaded and is being requested because an user
is creating a sctp socket.
During initialization, sctp will add the new protocol type and then
initialize pernet subsys:
status = sctp_v4_protosw_init();
if (status)
goto err_protosw_init;
status = sctp_v6_protosw_init();
if (status)
goto err_v6_protosw_init;
status = register_pernet_subsys(&sctp_net_ops);
The problem is that after those calls to sctp_v{4,6}_protosw_init(), it
is possible for userspace to create SCTP sockets like if the module is
already fully loaded. If that happens, one of the possible effects is
that we will have readers for net->sctp.local_addr_list list earlier
than expected and sctp_net_init() does not take precautions while
dealing with that list, leading to a potential panic but not limited to
that, as sctp_sock_init() will copy a bunch of blank/partially
initialized values from net->sctp.
The race happens like this:
CPU 0 | CPU 1
socket() |
__sock_create | socket()
inet_create | __sock_create
list_for_each_entry_rcu( |
answer, &inetsw[sock->type], |
list) { | inet_create
/* no hits */ |
if (unlikely(err)) { |
... |
request_module() |
/* socket creation is blocked |
* the module is fully loaded |
*/ |
sctp_init |
sctp_v4_protosw_init |
inet_register_protosw |
list_add_rcu(&p->list, |
last_perm); |
| list_for_each_entry_rcu(
| answer, &inetsw[sock->type],
sctp_v6_protosw_init | list) {
| /* hit, so assumes protocol
| * is already loaded
| */
| /* socket creation continues
| * before netns is initialized
| */
register_pernet_subsys |
Simply inverting the initialization order between
register_pernet_subsys() and sctp_v4_protosw_init() is not possible
because register_pernet_subsys() will create a control sctp socket, so
the protocol must be already visible by then. Deferring the socket
creation to a work-queue is not good specially because we loose the
ability to handle its errors.
So, as suggested by Vlad, the fix is to split netns initialization in
two moments: defaults and control socket, so that the defaults are
already loaded by when we register the protocol, while control socket
initialization is kept at the same moment it is today.
Fixes: 4db67e8086 ("sctp: Make the address lists per network namespace")
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0ca50d12fe added a restriction that the address must belong to
the output interface, so that sctp will use the right interface even
when using secondary addresses.
But it breaks IPVS setups, on which people is used to attach VIP
addresses to loopback interface on real servers. It's preferred to
attach to the interface actually in use, but it's a very common setup
and that used to work.
This patch then saves the first routing good result, even if it would be
going out through an interface that doesn't have that address. If no
better hit found, it's then used. This effectively restores the original
behavior if no better interface could be found.
Fixes: 0ca50d12fe ("sctp: fix src address selection if using secondary addresses")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0ca50d12fe failed to release the reference to dst entries that
it decided to skip.
Fixes: 0ca50d12fe ("sctp: fix src address selection if using secondary addresses")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In short, sctp is likely to incorrectly choose src address if socket is
bound to secondary addresses. This patch fixes it by adding a new check
that checks if such src address belongs to the interface that routing
identified as output.
This is enough to avoid rp_filter drops on remote peer.
Details:
Currently, sctp will do a routing attempt without specifying the src
address and compare the returned value (preferred source) with the
addresses that the socket is bound to. When using secondary addresses,
this will not match.
Then it will try specifying each of the addresses that the socket is
bound to and re-routing, checking if that address is valid as src for
that dst. Thing is, this check alone is weak:
# ip r l
192.168.100.0/24 dev eth1 proto kernel scope link src 192.168.100.149
192.168.122.0/24 dev eth0 proto kernel scope link src 192.168.122.147
# ip a l
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 52:54:00:15:18:6a brd ff:ff:ff:ff:ff:ff
inet 192.168.122.147/24 brd 192.168.122.255 scope global dynamic eth0
valid_lft 2160sec preferred_lft 2160sec
inet 192.168.122.148/24 scope global secondary eth0
valid_lft forever preferred_lft forever
inet6 fe80::5054:ff:fe15:186a/64 scope link
valid_lft forever preferred_lft forever
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 52:54:00:b3:91:46 brd ff:ff:ff:ff:ff:ff
inet 192.168.100.149/24 brd 192.168.100.255 scope global dynamic eth1
valid_lft 2162sec preferred_lft 2162sec
inet 192.168.100.148/24 scope global secondary eth1
valid_lft forever preferred_lft forever
inet6 fe80::5054:ff:feb3:9146/64 scope link
valid_lft forever preferred_lft forever
4: ens9: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 52:54:00:05:47:ee brd ff:ff:ff:ff:ff:ff
inet6 fe80::5054:ff:fe05:47ee/64 scope link
valid_lft forever preferred_lft forever
# ip r g 192.168.100.193 from 192.168.122.148
192.168.100.193 from 192.168.122.148 dev eth1
cache
Even if you specify an interface:
# ip r g 192.168.100.193 from 192.168.122.148 oif eth1
192.168.100.193 from 192.168.122.148 dev eth1
cache
Although this would be valid, peers using rp_filter will drop such
packets as their src doesn't match the routes for that interface.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paves the day for the next patch. Functionality stays untouched.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for changing how struct net is refcounted
on kernel sockets pass the knowledge that we are creating
a kernel socket from sock_create_kern through to sk_alloc.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of an effort to move skb->dropcount to skb->cb[] use a common
macro in protocol families using skb->cb[] for ancillary data to
validate available room in skb->cb[].
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull percpu updates from Tejun Heo:
"A lot of activities on percpu front. Notable changes are...
- percpu allocator now can take @gfp. If @gfp doesn't contain
GFP_KERNEL, it tries to allocate from what's already available to
the allocator and a work item tries to keep the reserve around
certain level so that these atomic allocations usually succeed.
This will replace the ad-hoc percpu memory pool used by
blk-throttle and also be used by the planned blkcg support for
writeback IOs.
Please note that I noticed a bug in how @gfp is interpreted while
preparing this pull request and applied the fix 6ae833c7fe
("percpu: fix how @gfp is interpreted by the percpu allocator")
just now.
- percpu_ref now uses longs for percpu and global counters instead of
ints. It leads to more sparse packing of the percpu counters on
64bit machines but the overhead should be negligible and this
allows using percpu_ref for refcnting pages and in-memory objects
directly.
- The switching between percpu and single counter modes of a
percpu_ref is made independent of putting the base ref and a
percpu_ref can now optionally be initialized in single or killed
mode. This allows avoiding percpu shutdown latency for cases where
the refcounted objects may be synchronously created and destroyed
in rapid succession with only a fraction of them reaching fully
operational status (SCSI probing does this when combined with
blk-mq support). It's also planned to be used to implement forced
single mode to detect underflow more timely for debugging.
There's a separate branch percpu/for-3.18-consistent-ops which cleans
up the duplicate percpu accessors. That branch causes a number of
conflicts with s390 and other trees. I'll send a separate pull
request w/ resolutions once other branches are merged"
* 'for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (33 commits)
percpu: fix how @gfp is interpreted by the percpu allocator
blk-mq, percpu_ref: start q->mq_usage_counter in atomic mode
percpu_ref: make INIT_ATOMIC and switch_to_atomic() sticky
percpu_ref: add PERCPU_REF_INIT_* flags
percpu_ref: decouple switching to percpu mode and reinit
percpu_ref: decouple switching to atomic mode and killing
percpu_ref: add PCPU_REF_DEAD
percpu_ref: rename things to prepare for decoupling percpu/atomic mode switch
percpu_ref: replace pcpu_ prefix with percpu_
percpu_ref: minor code and comment updates
percpu_ref: relocate percpu_ref_reinit()
Revert "blk-mq, percpu_ref: implement a kludge for SCSI blk-mq stall during probe"
Revert "percpu: free percpu allocation info for uniprocessor system"
percpu-refcount: make percpu_ref based on longs instead of ints
percpu-refcount: improve WARN messages
percpu: fix locking regression in the failure path of pcpu_alloc()
percpu-refcount: add @gfp to percpu_ref_init()
proportions: add @gfp to init functions
percpu_counter: add @gfp to percpu_counter_init()
percpu_counter: make percpu_counters_lock irq-safe
...
net.ipv4.ip_nonlocal_bind sysctl was global to all network
namespaces. This patch allows to set a different value for each
network namespace.
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Signed-off-by: David S. Miller <davem@davemloft.net>
Percpu allocator now supports allocation mask. Add @gfp to
percpu_counter_init() so that !GFP_KERNEL allocation masks can be used
with percpu_counters too.
We could have left percpu_counter_init() alone and added
percpu_counter_init_gfp(); however, the number of users isn't that
high and introducing _gfp variants to all percpu data structures would
be quite ugly, so let's just do the conversion. This is the one with
the most users. Other percpu data structures are a lot easier to
convert.
This patch doesn't make any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jan Kara <jack@suse.cz>
Acked-by: "David S. Miller" <davem@davemloft.net>
Cc: x86@kernel.org
Cc: Jens Axboe <axboe@kernel.dk>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
The SCTP socket extensions API document describes the v4mapping option as
follows:
8.1.15. Set/Clear IPv4 Mapped Addresses (SCTP_I_WANT_MAPPED_V4_ADDR)
This socket option is a Boolean flag which turns on or off the
mapping of IPv4 addresses. If this option is turned on, then IPv4
addresses will be mapped to V6 representation. If this option is
turned off, then no mapping will be done of V4 addresses and a user
will receive both PF_INET6 and PF_INET type addresses on the socket.
See [RFC3542] for more details on mapped V6 addresses.
This description isn't really in line with what the code does though.
Introduce addr_to_user (renamed addr_v4map), which should be called
before any sockaddr is passed back to user space. The new function
places the sockaddr into the correct format depending on the
SCTP_I_WANT_MAPPED_V4_ADDR option.
Audit all places that touched v4mapped and either sanely construct
a v4 or v6 address then call addr_to_user, or drop the
unnecessary v4mapped check entirely.
Audit all places that call addr_to_user and verify they are on a sycall
return path.
Add a custom getname that formats the address properly.
Several bugs are addressed:
- SCTP_I_WANT_MAPPED_V4_ADDR=0 often returned garbage for
addresses to user space
- The addr_len returned from recvmsg was not correct when
returning AF_INET on a v6 socket
- flowlabel and scope_id were not zerod when promoting
a v4 to v6
- Some syscalls like bind and connect behaved differently
depending on v4mapped
Tested bind, getpeername, getsockname, connect, and recvmsg for proper
behaviour in v4mapped = 1 and 0 cases.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't seem like an protocols are setting anything other
than the default, and allowing to arbitrarily disable checksums
for a whole protocol seems dangerous. This can be done on a per
socket basis.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 8f0ea0fe3a (snmp: reduce percpu needs by 50%)
reduced snmp array size to 1, so technically it doesn't have to be
an array any more. What's more, after the following commit:
commit 933393f58f
Date: Thu Dec 22 11:58:51 2011 -0600
percpu: Remove irqsafe_cpu_xxx variants
We simply say that regular this_cpu use must be safe regardless of
preemption and interrupt state. That has no material change for x86
and s390 implementations of this_cpu operations. However, arches that
do not provide their own implementation for this_cpu operations will
now get code generated that disables interrupts instead of preemption.
probably no arch wants to have SNMP_ARRAY_SZ == 2. At least after
almost 3 years, no one complains.
So, just convert the array to a single pointer and remove snmp_mib_init()
and snmp_mib_free() as well.
Cc: Christoph Lameter <cl@linux.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 813b3b5db8 (ipv4: Use caller's on-stack flowi as-is
in output route lookups.) introduces another regression which
is very similar to the problem of commit e6b45241c (ipv4: reset
flowi parameters on route connect) wants to fix:
Before we call ip_route_output_key() in sctp_v4_get_dst() to
get a dst that matches a bind address as the source address,
we have already called this function previously and the flowi
parameters have been initialized including flowi4_oif, so when
we call this function again, the process in __ip_route_output_key()
will be different because of the setting of flowi4_oif, and we'll
get a networking device which corresponds to the inputted flowi4_oif
as the output device, this is wrong because we'll never hit this
place if the previously returned source address of dst match one
of the bound addresses.
To reproduce this problem, a vlan setting is enough:
# ifconfig eth0 up
# route del default
# vconfig add eth0 2
# vconfig add eth0 3
# ifconfig eth0.2 10.0.1.14 netmask 255.255.255.0
# route add default gw 10.0.1.254 dev eth0.2
# ifconfig eth0.3 10.0.0.14 netmask 255.255.255.0
# ip rule add from 10.0.0.14 table 4
# ip route add table 4 default via 10.0.0.254 src 10.0.0.14 dev eth0.3
# sctp_darn -H 10.0.0.14 -P 36422 -h 10.1.4.134 -p 36422 -s -I
You'll detect that all the flow are routed to eth0.2(10.0.1.254).
Signed-off-by: Xufeng Zhang <xufeng.zhang@windriver.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_queue_xmit() assumes the skb it has to transmit is attached to an
inet socket. Commit 31c70d5956 ("l2tp: keep original skb ownership")
changed l2tp to not change skb ownership and thus broke this assumption.
One fix is to add a new 'struct sock *sk' parameter to ip_queue_xmit(),
so that we do not assume skb->sk points to the socket used by l2tp
tunnel.
Fixes: 31c70d5956 ("l2tp: keep original skb ownership")
Reported-by: Zhan Jianyu <nasa4836@gmail.com>
Tested-by: Zhan Jianyu <nasa4836@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redefined bh_[un]lock_sock to sctp_bh[un]lock_sock for user
space friendly code which we haven't use in years, so removing them.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When go the right path, the status is 0, no need to assign it again.
So just remove the assignment.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new ip_no_pmtu_disc mode only allowes fragmentation-needed errors
to be honored by protocols which do more stringent validation on the
ICMP's packet payload. This knob is useful for people who e.g. want to
run an unmodified DNS server in a namespace where they need to use pmtu
for TCP connections (as they are used for zone transfers or fallback
for requests) but don't want to use possibly spoofed UDP pmtu information.
Currently the whitelisted protocols are TCP, SCTP and DCCP as they check
if the returned packet is in the window or if the association is valid.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: John Heffner <johnwheffner@gmail.com>
Suggested-by: Florian Weimer <fweimer@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix checkpatch errors below:
ERROR: that open brace { should be on the previous line
ERROR: open brace '{' following function declarations go on the next line
ERROR: trailing statements should be on next line
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the restructuring of the lksctp.org site, we only allow bug
reports through the SCTP mailing list linux-sctp@vger.kernel.org,
not via SF, as SF is only used for web hosting and nothing more.
While at it, also remove the obvious statement that bugs will be
fixed and incooperated into the kernel.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the last module parameter for SCTP and make this
configurable via sysctl for SCTP like all the rest of SCTP's
configuration knobs.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP mailing list address to send patches or questions
to is linux-sctp@vger.kernel.org and not
lksctp-developers@lists.sourceforge.net anymore. Therefore,
update all occurences.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get rid of all own SCTP debug printk macros and use the ones
that the kernel offers anyway instead. This makes the code more readable
and conform to the kernel code, and offers all the features of dynamic
debbuging that pr_debug() et al has, such as only turning on/off portions
of debug messages at runtime through debugfs. The runtime cost of having
CONFIG_DYNAMIC_DEBUG enabled, but none of the debug statements printing,
is negligible [1]. If kernel debugging is completly turned off, then these
statements will also compile into "empty" functions.
While we're at it, we also need to change the Kconfig option as it /now/
only refers to the ifdef'ed code portions in outqueue.c that enable further
debugging/tracing of SCTP transaction fields. Also, since SCTP_ASSERT code
was enabled with this Kconfig option and has now been removed, we
transform those code parts into WARNs resp. where appropriate BUG_ONs so
that those bugs can be more easily detected as probably not many people
have SCTP debugging permanently turned on.
To turn on all SCTP debugging, the following steps are needed:
# mount -t debugfs none /sys/kernel/debug
# echo -n 'module sctp +p' > /sys/kernel/debug/dynamic_debug/control
This can be done more fine-grained on a per file, per line basis and others
as described in [2].
[1] https://www.kernel.org/doc/ols/2009/ols2009-pages-39-46.pdf
[2] Documentation/dynamic-debug-howto.txt
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP_STATIC is just another define for the static keyword. It's use
is inconsistent in the SCTP code anyway and it was introduced in the
initial implementation of SCTP in 2.5. We have a regression suite in
lksctp-tools, but this is for user space only, so noone makes use of
this macro anymore. The kernel test suite for 2.5 is incompatible with
the current SCTP code anyway.
So simply Remove it, to be more consistent with the rest of the kernel
code.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
t_new rather obfuscates things where everyone else is using actual
function names instead of that macro, so replace it with kzalloc,
which is the function t_new wraps.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
