When there is only one byte in a frag, the current calculation
using "(size + HNS3_MAX_BD_SIZE - 1) >> HNS3_MAX_BD_SIZE_OFFSET"
will return zero, because HNS3_MAX_BD_SIZE is 65535 and
HNS3_MAX_BD_SIZE_OFFSET is 16. So it will cause tx error when
a frag's size is one byte.
This patch fixes it by using DIV_ROUND_UP.
Fixes: 3fe13ed95d ("net: hns3: avoid mult + div op in critical data path")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit bfcb79fca1
("PCI/ERR: Run error recovery callbacks for all affected devices")
affected the non-fatal error recovery logic for the HNS and RDMA devices.
This is because each HNS PF under PCIe bus receive callbacks
from the AER driver when an error is reported for one of the PF.
This causes unwanted PF resets because
the HNS decides which PF to reset based on the reset type set.
The HNS error handling code sets the reset type based on the hw error
type detected.
This patch provides fix for the above issue for the recovery of
the hw errors in the HNS and RDMA devices.
This patch needs backporting to the kernel v5.0+
Fixes: 332fbf5765 ("net: hns3: add handling of hw ras errors using new set of commands")
Reported-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW can not guarantee complete write desc->rx.size, even though
HNS3_RXD_VLD_B has been set. Driver needs to add dma_rmb()
instruction to make sure desc->rx.size is always valid.
Fixes: e559709505 ("net: hns3: Add handling of GRO Pkts not fully RX'ed in NAPI poll")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were a couple logical ORs accidentally mixed in with the bitwise
ORs.
Fixes: e8149933b1 ("net: hns3: remove hnae3_get_bit in data path")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(struct boo) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If hns3_client_start() failed in the hns3_client_init(),
register_dev() should be undo in its error handling.
Fixes: a6d818e31d ("net: hns3: Add vport alive state checking support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Presently the hns reset_type for the roce errors is set
in the hclge_log_and_clear_rocee_ras_error function.
This function is also called to detect and clear roce errors
while enabling the rdma error interrupts. However there is no hns
reset requested for this case. This can cause issue of wrong
reset_type used with subsequent hns reset as the
reset_type set in the above case was not cleared.
This patch moves setting of hns reset_type for the roce errors from
hclge_log_and_clear_rocee_ras_error function
to hclge_handle_rocee_ras_error.
Fixes: 630ba007f4 ("net: hns3: add handling of RDMA RAS errors")
Reported-by: Huazhong Tan <tanhuazhong@huawei.com>
Reported-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For revision 0x20, VF shares the same RSS config with PF.
In original codes, it always return 0 when query RSS hash
key for VF. This patch fixes it by return the hash key
got from PF.
Fixes: 374ad29176 ("net: hns3: net: hns3: Add RSS general configuration support for VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For revision 0x21, the switch of VF VLAN filter is per function.
It's necessary to enable VF VLAN filter for each VF when initializing.
Otherwise, VF will be able to receive broadcast packets with unknown
VLAN when PF enters promisc mode.
Fixes: 64d114f0a7 ("net: hns3: Add egress/ingress vlan filter for revision 0x21")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to config depth for tx|rx ring separately
by ethtool command "-G".
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hnae3_get_bit uses hnae3_get_field, and hnae3_get_field
masks the data, which is unnecessary in data path.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hnae3_set_bit and hnae3_set_field masks the data before setting
the field or bit, which is unnecessary because the data is already
zero initialized.
Suggested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds unlikely hint for error handling in critical data
path.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fill_desc ops has only one implementation, and
get_rxd_bnum has not been used, so this patch removes
them.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch limits some variables' scope as much as possible in
hns3_fill_desc.
Also, only set l3_type and l4_type when necessary.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses shift offset to avoid doing mult and div operation.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds xps setting support for hns3 driver based on
the interrupt affinity info.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the hardware's description, the driver should clear
the command queue's registers when uloading VF driver. Otherwise,
these existing value may lead the IMP get into a wrong state.
Fixes: fedd0c15d2 ("net: hns3: Add HNS3 VF IMP(Integrated Management Proc) cmd interface")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the hardware's description, the driver should clear
the command queue's registers when uloading driver. Otherwise,
these existing value may lead the IMP get into a wrong state.
Also this patch adds hclge_cmd_uninit() to do the command queue
uninitialization which includes clearing registers and freeing
memory.
Fixes: 68c0a5c706 ("net: hns3: Add HNS3 IMP(Integrated Mgmt Proc) Cmd Interface Support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Record the vlan tables that the VF sends to the chip.
After the VF exception, the PF actively clears the VF to chip config.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Record the unicast and multicast tables that the VF sends to the chip.
After the VF exception, the PF actively clears the VF to chip config.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modify print message of 6th bit of ppp mpf abnormal errors,
there is a extra letter e in it.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These bits are enabled now and have been test.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 3rd and 4th of PPU(RCB) PF Abnormal is RAS errors instead of MSI-X
like other bits. This patch adds process of handling and logging this
two bits. Otherwise, this patch modifies print message of 28th and 29th
bit of PPU MPF Abnormal errors, which keep same with other errors now.
Fixes: f69b10b317 ("net: hns3: handle hw errors of PPU(RCB)")
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add information of specific bit in log to be consistent
with other type of errors, so that we can know which memory of ssu
has occurred a ecc ras errors.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original codes, for copper port which doesn't connect to phy,
it always returns -EOPNOTSUPP when query port information. This
patch fixes it by return the port information of MAC.
Fixes: 5f373b1585 ("net: hns3: Fix speed/duplex information loss problem when executing ethtool ethx cmd of VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link mode with bits has been up to more than 31 for some MAC
and phy. Convert to using a linkmode bitmap, which can support all
link modes.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hnae3_register_ae_dev(), ae_algo->ops is assigned to ae_dev->ops
before check that ae_algo->ops is valid.
And in hnae3_register_ae_algo(), missing check for ae_algo->ops.
This patch fixes them.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions are exported, add pointer checking at the beginning
can make them more safe.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the missing device reference release-after-use in
the positive leg of the roce reset API of the HNS DSAF.
Fixes: c969c6e7ab ("net: hns: Fix object reference leaks in hns_dsaf_roce_reset()")
Reported-by: John Garry <john.garry@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:2431:5: warning:
symbol 'hclge_set_all_vf_rst' was not declared. Should it be static?
Fixes: aa5c4f175b ("net: hns3: add reset handling for VF when doing PF reset")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.
Signed-off-by: Huang Zijiang <huang.zijiang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
When updating the available MAC VLAN table counts,
MAC VLAN table entry count function adds
operation 0 value protection measures.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to prevent the variable anomaly from being larger than desc_num,
the upper limit judgment condition becomes >=.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user disables vlan filter, and adds vlan device, it won't
notify the driver the update the vlan filter. In this case, when
user enables vlan filter again, the packets with new vlan tag
will be filtered by vlan filter.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple macros with the largest number of TCs in the system,
optimized to HCLGE_MAX_TC_NUM.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Run ethtool ethx when displaying device information in VF，
the supported port and link mode items will be empty.
This patch fixes it.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the TC is enabled, we need to check whether the buffer is enough,
otherwise it may lead to a wrong -ENOMEM case.
Fixes: 9ffe79a9c2 ("net: hns3: Support for dynamically assigning tx buffer to TC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does not change the code logic. There are some same
set_bit statements called by add/rm_uc/mc_addr_common, and move
this statements into hclge_prepare_mac_addr to reduce duplicate
code.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For simplifying the code, this patch adds hclge_cmd_check_retval() to
check the return value of the command.
Also, according the IMP's description, when there are several descriptors
in a command, then the IMP will save the return value on the last
description, so hclge_cmd_check_retval() just check the last one for this
case.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are four steps to calcuate the rx private buffer, each step
can be done in a function to avoid code duplication and aid code
readability.
This patch adds three separate functions do the job. Also, the
function name more or less make the comment redundant, so remove
some obvious comment.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The second parameter to the hook function set_gro_en is always passed in
true/false, so modify it's type from int to bool.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 supports setting rx-usecs|tx-usecs as 0, but it will not
update dynamically when adaptive-tx or adaptive-rx is enable.
This patch removes the Redundant check.
Fixes: a95e1f8666 ("net: hns3: change the time interval of int_gl calculating")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the same code style for rx_group and tx_group in the
hns3_update_new_int_gl().
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should return -ENOMEM if the kcalloc() fails.
Fixes: d174ea75c9 ("net: hns3: add statistics for PFC frames and MAC control frame")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In orginal codes, driver always enables flow director when
intializing. When user disable flow director with command
ethtool -K, the flow director will be enabled again after
resetting.
This patch fixes it by only enabling it when first initialzing.
Fixes: 6871af29b3 ("net: hns3: Add reset handle for flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VF is resetting, it can't communicate to PF with mailbox msg.
This patch adds reset state checking before sending keep alive msg
to PF.
Fixes: a6d818e31d ("net: hns3: Add vport alive state checking support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 VF driver support NIC and Roce, hdev stores NIC
handle and Roce handle, should use correct parameter for
container_of.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
