Currently we unmap the DMA range, then copy to new skb.
Change this so we can keep the mapping in case the data is copied.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Its the same in both handlers.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
... and make it static.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixed many errors/warnings and checks in e1000_ethtool.c reported
by checkpatch.pl. Suggestions from Joe Perches and Alexander Duyck
applied as well
Signed-off-by: Krzysztof Majzerowicz-Jaszcz <cristos@vipserv.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This device claims TSO and checksum support for vlans. It also
allows a user to control vlan acceleration offloading. As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO and checksum information.
This will results in corrupted frames sent on the wire.
This patch extract the protocol value correctly and corrects TSO
for non-accelerated traffic.
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
To be future-proof and for better readability the time comparisons are modified
to use time_after() instead of plain, error-prone math.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no case skb->len would be 0 or 'negative'.
Remove the check.
Signed-off-by: Yongjian Xu <xuyongjiande@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the is_broadcast_ether_addr/is_multicast_ether_addr helper functions
from linux/etherdevice.h instead of open coding them.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000_hw.c contains a lot of debug messages which print
name of invoked function and contain no new line character
at the end. Remove them as equivalent information can be
nowadays obtained using function tracer.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On e1000_down(), we should ensure every asynchronous work is canceled
before proceeding. Since the watchdog_task can schedule other works
apart from itself, it should be stopped first, but currently it is
stopped after the reset_task. This can result in the following race
leading to the reset_task running after the module unload:
e1000_down_and_stop(): e1000_watchdog():
---------------------- -----------------
cancel_work_sync(reset_task)
schedule_work(reset_task)
cancel_delayed_work_sync(watchdog_task)
The patch moves cancel_delayed_work_sync(watchdog_task) at the beginning
of e1000_down_and_stop() thus ensuring the race is impossible.
Cc: Tushar Dave <tushar.n.dave@intel.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The patch fixes the following lockdep warning, which is 100%
reproducible on network restart:
======================================================
[ INFO: possible circular locking dependency detected ]
3.12.0+ #47 Tainted: GF
-------------------------------------------------------
kworker/1:1/27 is trying to acquire lock:
((&(&adapter->watchdog_task)->work)){+.+...}, at: [<ffffffff8108a5b0>] flush_work+0x0/0x70
but task is already holding lock:
(&adapter->mutex){+.+...}, at: [<ffffffffa0177c0a>] e1000_reset_task+0x4a/0xa0 [e1000]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&adapter->mutex){+.+...}:
[<ffffffff810bdb5d>] lock_acquire+0x9d/0x120
[<ffffffff816b8cbc>] mutex_lock_nested+0x4c/0x390
[<ffffffffa017233d>] e1000_watchdog+0x7d/0x5b0 [e1000]
[<ffffffff8108b972>] process_one_work+0x1d2/0x510
[<ffffffff8108ca80>] worker_thread+0x120/0x3a0
[<ffffffff81092c1e>] kthread+0xee/0x110
[<ffffffff816c3d7c>] ret_from_fork+0x7c/0xb0
-> #0 ((&(&adapter->watchdog_task)->work)){+.+...}:
[<ffffffff810bd9c0>] __lock_acquire+0x1710/0x1810
[<ffffffff810bdb5d>] lock_acquire+0x9d/0x120
[<ffffffff8108a5eb>] flush_work+0x3b/0x70
[<ffffffff8108b5d8>] __cancel_work_timer+0x98/0x140
[<ffffffff8108b693>] cancel_delayed_work_sync+0x13/0x20
[<ffffffffa0170cec>] e1000_down_and_stop+0x3c/0x60 [e1000]
[<ffffffffa01775b1>] e1000_down+0x131/0x220 [e1000]
[<ffffffffa0177c12>] e1000_reset_task+0x52/0xa0 [e1000]
[<ffffffff8108b972>] process_one_work+0x1d2/0x510
[<ffffffff8108ca80>] worker_thread+0x120/0x3a0
[<ffffffff81092c1e>] kthread+0xee/0x110
[<ffffffff816c3d7c>] ret_from_fork+0x7c/0xb0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&adapter->mutex);
lock((&(&adapter->watchdog_task)->work));
lock(&adapter->mutex);
lock((&(&adapter->watchdog_task)->work));
*** DEADLOCK ***
3 locks held by kworker/1:1/27:
#0: (events){.+.+.+}, at: [<ffffffff8108b906>] process_one_work+0x166/0x510
#1: ((&adapter->reset_task)){+.+...}, at: [<ffffffff8108b906>] process_one_work+0x166/0x510
#2: (&adapter->mutex){+.+...}, at: [<ffffffffa0177c0a>] e1000_reset_task+0x4a/0xa0 [e1000]
stack backtrace:
CPU: 1 PID: 27 Comm: kworker/1:1 Tainted: GF 3.12.0+ #47
Hardware name: System manufacturer System Product Name/P5B-VM SE, BIOS 0501 05/31/2007
Workqueue: events e1000_reset_task [e1000]
ffffffff820f6000 ffff88007b9dba98 ffffffff816b54a2 0000000000000002
ffffffff820f5e50 ffff88007b9dbae8 ffffffff810ba936 ffff88007b9dbac8
ffff88007b9dbb48 ffff88007b9d8f00 ffff88007b9d8780 ffff88007b9d8f00
Call Trace:
[<ffffffff816b54a2>] dump_stack+0x49/0x5f
[<ffffffff810ba936>] print_circular_bug+0x216/0x310
[<ffffffff810bd9c0>] __lock_acquire+0x1710/0x1810
[<ffffffff8108a5b0>] ? __flush_work+0x250/0x250
[<ffffffff810bdb5d>] lock_acquire+0x9d/0x120
[<ffffffff8108a5b0>] ? __flush_work+0x250/0x250
[<ffffffff8108a5eb>] flush_work+0x3b/0x70
[<ffffffff8108a5b0>] ? __flush_work+0x250/0x250
[<ffffffff8108b5d8>] __cancel_work_timer+0x98/0x140
[<ffffffff8108b693>] cancel_delayed_work_sync+0x13/0x20
[<ffffffffa0170cec>] e1000_down_and_stop+0x3c/0x60 [e1000]
[<ffffffffa01775b1>] e1000_down+0x131/0x220 [e1000]
[<ffffffffa0177c12>] e1000_reset_task+0x52/0xa0 [e1000]
[<ffffffff8108b972>] process_one_work+0x1d2/0x510
[<ffffffff8108b906>] ? process_one_work+0x166/0x510
[<ffffffff8108ca80>] worker_thread+0x120/0x3a0
[<ffffffff8108c960>] ? manage_workers+0x2c0/0x2c0
[<ffffffff81092c1e>] kthread+0xee/0x110
[<ffffffff81092b30>] ? __init_kthread_worker+0x70/0x70
[<ffffffff816c3d7c>] ret_from_fork+0x7c/0xb0
[<ffffffff81092b30>] ? __init_kthread_worker+0x70/0x70
== The issue background ==
The problem occurs, because e1000_down(), which is called under
adapter->mutex by e1000_reset_task(), tries to synchronously cancel
e1000 auxiliary works (reset_task, watchdog_task, phy_info_task,
fifo_stall_task), which take adapter->mutex in their handlers. So the
question is what does adapter->mutex protect there?
The adapter->mutex was introduced by commit 0ef4ee ("e1000: convert to
private mutex from rtnl") as a replacement for rtnl_lock() taken in the
asynchronous handlers. It targeted on fixing a similar lockdep warning
issued when e1000_down() was called under rtnl_lock(), and it fixed it,
but unfortunately it introduced the lockdep warning described above.
Anyway, that said the source of this bug is that the asynchronous works
were made to take rtnl_lock() some time ago, so let's look deeper and
find why it was added there.
The rtnl_lock() was added to asynchronous handlers by commit 338c15
("e1000: fix occasional panic on unload") in order to prevent
asynchronous handlers from execution after the module is unloaded
(e1000_down() is called) as it follows from the comment to the commit:
> Net drivers in general have an issue where timers fired
> by mod_timer or work threads with schedule_work are running
> outside of the rtnl_lock.
>
> With no other lock protection these routines are vulnerable
> to races with driver unload or reset paths.
>
> The longer term solution to this might be a redesign with
> safer locks being taken in the driver to guarantee no
> reentrance, but for now a safe and effective fix is
> to take the rtnl_lock in these routines.
I'm not sure if this locking scheme fixed the problem or just made it
unlikely, although I incline to the latter. Anyway, this was long time
ago when e1000 auxiliary works were implemented as timers scheduling
real work handlers in their routines. The e1000_down() function only
canceled the timers, but left the real handlers running if they were
running, which could result in work execution after module unload.
Today, the e1000 driver uses sane delayed works instead of the pair
timer+work to implement its delayed asynchronous handlers, and the
e1000_down() synchronously cancels all the works so that the problem
that commit 338c15 tried to cope with disappeared, and we don't need any
locks in the handlers any more. Moreover, any locking there can
potentially result in a deadlock.
So, this patch reverts commits 0ef4ee and 338c15.
Fixes: 0ef4eedc2e ("e1000: convert to private mutex from rtnl")
Fixes: 338c15e470 ("e1000: fix occasional panic on unload")
Cc: Tushar Dave <tushar.n.dave@intel.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is based on a similar change made to e1000e support in
commit bb9e44d0d0 ("e1000e: prevent oops when adapter is being closed
and reset simultaneously"). The same issue has also been observed
on the older e1000 cards.
Here, we have increased the RESET_COUNT value to 50 because there are too
many accesses to e1000 nic on stress tests to e1000 nic, it is not enough
to set RESET_COUT 25. Experimentation has shown that it is enough to set
RESET_COUNT 50.
Signed-off-by: yzhu1 <yanjun.zhu@windriver.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
tx_ring and adapter->tx_ring are already of type "struct
e1000_tx_ring *"
Signed-off-by: Hong Zhiguo <zhiguohong@tencent.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Replace the following sequence:
dma_set_mask(dev, mask);
dma_set_coherent_mask(dev, mask);
with a call to the new helper dma_set_mask_and_coherent().
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
__GFP_ZERO is an uncommon flag and perhaps is better
not used. static inline dma_zalloc_coherent exists
so convert the uses of dma_alloc_coherent with __GFP_ZERO
to the more common kernel style with zalloc.
Remove memset from the static inline dma_zalloc_coherent
and add just one use of __GFP_ZERO instead.
Trivially reduces the size of the existing uses of
dma_zalloc_coherent.
Realign arguments as appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h
Two minor conflicts in wireless. Overlapping additions of extern
declarations in net/wireless/core.h and a bug fix overlapping with
the addition of a boolean parameter to __ieee80211_key_free().
Signed-off-by: David S. Miller <davem@davemloft.net>
After dma_map_single, dma_mapping_error must be called.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the number of calls required to alloc
a zeroed block of memory.
Trivially reduces overall object size.
Other changes around these removals
o Neaten call argument alignment
o Remove an unnecessary OOM message after dma_alloc_coherent failure
o Remove unnecessary gfp_t stack variable
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.
Remove the unnecessary additional error logging.
Around these deletions:
o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes whitespace issues, such as lines exceeding 80 chars, needless blank
lines and the use of spaces where tabs are needed. In addition, fix
multi-line comments to align with the networking standard.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
alloc failures already get standardized OOM
messages and a dump_stack.
For the affected mallocs around these OOM messages:
Converted kmallocs with multiplies to kmalloc_array.
Converted a kmalloc/memcpy to kmemdup.
Removed now unused stack variables.
Removed unnecessary parentheses.
Neatened alignment.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
perm_addr is initialized correctly in register_netdevice() so to init it in
drivers is no longer needed.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers. This patch fixes all of
them back up to be properly aligned.
Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Tushar Dave <tushar.n.dave@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The e1000 driver currently does not protect concurrent accesses to the PHY
from both the ethtool callbacks, and from the e1000_watchdog function. This
patchs adds a new spinlock which is used by e1000_{read,write}_phy_reg in
order to serialize concurrent accesses to the PHY.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking changes from David Miller:
1) GRE now works over ipv6, from Dmitry Kozlov.
2) Make SCTP more network namespace aware, from Eric Biederman.
3) TEAM driver now works with non-ethernet devices, from Jiri Pirko.
4) Make openvswitch network namespace aware, from Pravin B Shelar.
5) IPV6 NAT implementation, from Patrick McHardy.
6) Server side support for TCP Fast Open, from Jerry Chu and others.
7) Packet BPF filter supports MOD and XOR, from Eric Dumazet and Daniel
Borkmann.
8) Increate the loopback default MTU to 64K, from Eric Dumazet.
9) Use a per-task rather than per-socket page fragment allocator for
outgoing networking traffic. This benefits processes that have very
many mostly idle sockets, which is quite common.
From Eric Dumazet.
10) Use up to 32K for page fragment allocations, with fallbacks to
smaller sizes when higher order page allocations fail. Benefits are
a) less segments for driver to process b) less calls to page
allocator c) less waste of space.
From Eric Dumazet.
11) Allow GRO to be used on GRE tunnels, from Eric Dumazet.
12) VXLAN device driver, one way to handle VLAN issues such as the
limitation of 4096 VLAN IDs yet still have some level of isolation.
From Stephen Hemminger.
13) As usual there is a large boatload of driver changes, with the scale
perhaps tilted towards the wireless side this time around.
Fix up various fairly trivial conflicts, mostly caused by the user
namespace changes.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1012 commits)
hyperv: Add buffer for extended info after the RNDIS response message.
hyperv: Report actual status in receive completion packet
hyperv: Remove extra allocated space for recv_pkt_list elements
hyperv: Fix page buffer handling in rndis_filter_send_request()
hyperv: Fix the missing return value in rndis_filter_set_packet_filter()
hyperv: Fix the max_xfer_size in RNDIS initialization
vxlan: put UDP socket in correct namespace
vxlan: Depend on CONFIG_INET
sfc: Fix the reported priorities of different filter types
sfc: Remove EFX_FILTER_FLAG_RX_OVERRIDE_IP
sfc: Fix loopback self-test with separate_tx_channels=1
sfc: Fix MCDI structure field lookup
sfc: Add parentheses around use of bitfield macro arguments
sfc: Fix null function pointer in efx_sriov_channel_type
vxlan: virtual extensible lan
igmp: export symbol ip_mc_leave_group
netlink: add attributes to fdb interface
tg3: unconditionally select HWMON support when tg3 is enabled.
Revert "net: ti cpsw ethernet: allow reading phy interface mode from DT"
gre: fix sparse warning
...
Host bridge hotplug
- Protect acpi_pci_drivers and acpi_pci_roots (Taku Izumi)
- Clear host bridge resource info to avoid issue when releasing (Yinghai Lu)
- Notify acpi_pci_drivers when hot-plugging host bridges (Jiang Liu)
- Use standard list ops for acpi_pci_drivers (Jiang Liu)
Device hotplug
- Use pci_get_domain_bus_and_slot() to close hotplug races (Jiang Liu)
- Remove fakephp driver (Bjorn Helgaas)
- Fix VGA ref count in hotplug remove path (Yinghai Lu)
- Allow acpiphp to handle PCIe ports without native hotplug (Jiang Liu)
- Implement resume regardless of pciehp_force param (Oliver Neukum)
- Make pci_fixup_irqs() work after init (Thierry Reding)
Miscellaneous
- Add pci_pcie_type(dev) and remove pci_dev.pcie_type (Yijing Wang)
- Factor out PCI Express Capability accessors (Jiang Liu)
- Add pcibios_window_alignment() so powerpc EEH can use generic resource assignment (Gavin Shan)
- Make pci_error_handlers const (Stephen Hemminger)
- Cleanup drivers/pci/remove.c (Bjorn Helgaas)
- Improve Vendor-Specific Extended Capability support (Bjorn Helgaas)
- Use standard list ops for bus->devices (Bjorn Helgaas)
- Avoid kmalloc in pci_get_subsys() and pci_get_class() (Feng Tang)
- Reassign invalid bus number ranges (Intel DP43BF workaround) (Yinghai Lu)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=haBu
-----END PGP SIGNATURE-----
Merge tag 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug
- Protect acpi_pci_drivers and acpi_pci_roots (Taku Izumi)
- Clear host bridge resource info to avoid issue when releasing
(Yinghai Lu)
- Notify acpi_pci_drivers when hot-plugging host bridges (Jiang Liu)
- Use standard list ops for acpi_pci_drivers (Jiang Liu)
Device hotplug
- Use pci_get_domain_bus_and_slot() to close hotplug races (Jiang
Liu)
- Remove fakephp driver (Bjorn Helgaas)
- Fix VGA ref count in hotplug remove path (Yinghai Lu)
- Allow acpiphp to handle PCIe ports without native hotplug (Jiang
Liu)
- Implement resume regardless of pciehp_force param (Oliver Neukum)
- Make pci_fixup_irqs() work after init (Thierry Reding)
Miscellaneous
- Add pci_pcie_type(dev) and remove pci_dev.pcie_type (Yijing Wang)
- Factor out PCI Express Capability accessors (Jiang Liu)
- Add pcibios_window_alignment() so powerpc EEH can use generic
resource assignment (Gavin Shan)
- Make pci_error_handlers const (Stephen Hemminger)
- Cleanup drivers/pci/remove.c (Bjorn Helgaas)
- Improve Vendor-Specific Extended Capability support (Bjorn
Helgaas)
- Use standard list ops for bus->devices (Bjorn Helgaas)
- Avoid kmalloc in pci_get_subsys() and pci_get_class() (Feng Tang)
- Reassign invalid bus number ranges (Intel DP43BF workaround)
(Yinghai Lu)"
* tag 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (102 commits)
PCI: acpiphp: Handle PCIe ports without native hotplug capability
PCI/ACPI: Use acpi_driver_data() rather than searching acpi_pci_roots
PCI/ACPI: Protect acpi_pci_roots list with mutex
PCI/ACPI: Use acpi_pci_root info rather than looking it up again
PCI/ACPI: Pass acpi_pci_root to acpi_pci_drivers' add/remove interface
PCI/ACPI: Protect acpi_pci_drivers list with mutex
PCI/ACPI: Notify acpi_pci_drivers when hot-plugging PCI root bridges
PCI/ACPI: Use normal list for struct acpi_pci_driver
PCI/ACPI: Use DEVICE_ACPI_HANDLE rather than searching acpi_pci_roots
PCI: Fix default vga ref_count
ia64/PCI: Clear host bridge aperture struct resource
x86/PCI: Clear host bridge aperture struct resource
PCI: Stop all children first, before removing all children
Revert "PCI: Use hotplug-safe pci_get_domain_bus_and_slot()"
PCI: Provide a default pcibios_update_irq()
PCI: Discard __init annotations for pci_fixup_irqs() and related functions
PCI: Use correct type when freeing bus resource list
PCI: Check P2P bridge for invalid secondary/subordinate range
PCI: Convert "new_id"/"remove_id" into generic pci_bus driver attributes
xen-pcifront: Use hotplug-safe pci_get_domain_bus_and_slot()
...
Conflicts:
drivers/net/team/team.c
drivers/net/usb/qmi_wwan.c
net/batman-adv/bat_iv_ogm.c
net/ipv4/fib_frontend.c
net/ipv4/route.c
net/l2tp/l2tp_netlink.c
The team, fib_frontend, route, and l2tp_netlink conflicts were simply
overlapping changes.
qmi_wwan and bat_iv_ogm were of the "use HEAD" variety.
With help from Antonio Quartulli.
Signed-off-by: David S. Miller <davem@davemloft.net>
On PCI/PCI-X HW, if packet size is less than ETH_ZLEN,
packets may get corrupted during padding by HW.
To WA this issue, pad all small packets manually.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Otto Estuardo Solares Cabrera <solca@galileo.edu>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the implementation in e1000 to allow ethtool to force
MDI state, allowing users to work around some improperly
behaving switches.
Forcing in this driver is for now only allowed when auto-neg is enabled.
To use must have the matching version of ethtool app that supports
this functionality.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown aaron.f.brown@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This driver now offers software transmit time stamping, so it should
advertise that fact via ethtool. Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert doxygen (or similar) formatted comments to kernel-doc or
unformatted comment. Delete a few that are content-free.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches. Delete
a few that are content-free.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is another fixup where the data is not transfered into buffer
addressed by skb->data but into a page.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Killing reset task while adapter is resetting causes deadlock.
Only kill reset task if adapter is not resetting.
Ref bug #43132 on bugzilla.kernel.org
CC: stable@vger.kernel.org
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code seems to want to look at the last byte where the HW puts some
information. Since the skb->data area is never seen by the HW I guess it
does not work as expected. We pass the page address to the HW so I
*think* in order to get to the last byte where the information might be
one should use the page buffer and take a look.
This is of course not more than just compile tested.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to the comment, errata 23 says that the memory we allocate
can't cross a 64KiB boundary. In case of jumbo frames we allocate
complete pages which can never cross the 64KiB boundary because
PAGE_SIZE should be a multiple of 64KiB so we stop either before the
boundary or start after it but never cross it. Furthermore the check
seems bogus because it looks at skb->data which is not seen by the HW
at all because we only pass the DMA address of the page we allocated. So
I *think* the workaround is not required here.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows the NIC to receive errored frames (bad FCS, etc)
and pass them up the stack. This can be useful when using
sniffers.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Dan Carpenter noticed that ixgbevf initial default was different than
the rest. But the problem is broader than that, only one Intel driver (ixgb)
was doing it almost right.
The convention for default debug level should be consistent among
Intel drivers and follow established convention.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a regression introduced by commit "e1000: do vlan
cleanup (799d531)".
Apparently some e1000 chips (not mine) are sensitive about the order of
setting vlan filter and vlan stripping/inserting functionality. So this
patch changes the order so it's the same as before vlan cleanup.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull kmap_atomic cleanup from Cong Wang.
It's been in -next for a long time, and it gets rid of the (no longer
used) second argument to k[un]map_atomic().
Fix up a few trivial conflicts in various drivers, and do an "evil
merge" to catch some new uses that have come in since Cong's tree.
* 'kmap_atomic' of git://github.com/congwang/linux: (59 commits)
feature-removal-schedule.txt: schedule the deprecated form of kmap_atomic() for removal
highmem: kill all __kmap_atomic() [swarren@nvidia.com: highmem: Fix ARM build break due to __kmap_atomic rename]
drbd: remove the second argument of k[un]map_atomic()
zcache: remove the second argument of k[un]map_atomic()
gma500: remove the second argument of k[un]map_atomic()
dm: remove the second argument of k[un]map_atomic()
tomoyo: remove the second argument of k[un]map_atomic()
sunrpc: remove the second argument of k[un]map_atomic()
rds: remove the second argument of k[un]map_atomic()
net: remove the second argument of k[un]map_atomic()
mm: remove the second argument of k[un]map_atomic()
lib: remove the second argument of k[un]map_atomic()
power: remove the second argument of k[un]map_atomic()
kdb: remove the second argument of k[un]map_atomic()
udf: remove the second argument of k[un]map_atomic()
ubifs: remove the second argument of k[un]map_atomic()
squashfs: remove the second argument of k[un]map_atomic()
reiserfs: remove the second argument of k[un]map_atomic()
ocfs2: remove the second argument of k[un]map_atomic()
ntfs: remove the second argument of k[un]map_atomic()
...
Use pr_<level> for printk
Use temporary instead of multiple pr_conts
Coalesce formats.
Save a few bytes of object code too:
$ size drivers/net/ethernet/intel/e1000/e1000_main.o*
text data bss dec hex filename
60507 369 14120 74996 124f4
drivers/net/ethernet/intel/e1000/e1000_main.o.new
60717 369 14176 75262 125fe
drivers/net/ethernet/intel/e1000/e1000_main.o.old
Removed printing of pktdata.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Separate a complicated bit of e1000_config_dsp_after_link_change
into a new static function e1000_1000Mb_check_cable_length.
Reduces indentation and adds a bit of clarity.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This allows the NIC to pass the Ethernet Frame Checksum
(FCS) up the stack. Useful when sniffing packets.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Good for testing the RX logic for bad CRC handling.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit d5bc77a223 broke Wake-on-LAN by
inadvertently dropping the enabling of DMA receives.
Restore the enabling of DMA receives for WoL.
This is applicable to 3.1+ stable trees.
CC: stable@vger.stable.org
Reported-by: Tobias Klausmann <klausman@schwarzvogel.de>
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Tested-by: Tobias Klausmann <klausman@schwarzvogel.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When TX hang occurs e1000_dump prints TX ring, RX ring and Device registers.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.
Remove the allocation failure messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A global variable is currently used to hold the virtual address of the
CE4100 MDIO base register address. Store the address in the e1000_hw
structure and update macros accordingly.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are not unmapping ce4100_gbe_mdio_base_virt in exit path in case
we are running on a CE4100 adapter, fix that.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Steven Rostedt, e1000 has a lockdep splat added
during the recent merge window. The issue is that
cancel_delayed_work is called while holding our private mutex.
There is no reason that I can see to hold the mutex during pci
shutdown, it was more just paranoia that I put the mutex_lock
around the call to e1000_down.
In a quick survey lots of drivers handle locking differently when
being called by the pci layer. The assumption here is that we
don't need the mutexes' protection in this function because
the driver could not be unloaded while in the shutdown handler
which is only called at reboot or poweroff.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DaveM said:
Please, this kind of stuff rots forever and not using bool properly
drives me crazy.
Joe Perches <joe@perches.com> gave me the spatch script:
@@
bool b;
@@
-b = 0
+b = false
@@
bool b;
@@
-b = 1
+b = true
I merely installed coccinelle, read the documentation and took credit.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let caller know the result of adding/removing vlan id to/from vlan
filter.
In some drivers I make those functions to just return 0. But in those
where there is able to see if hw setup went correctly, return value is
set appropriately.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per discussion with Ben Hutchings and David Miller, go through and
remove assignments of "N/A" to fw_version in various drivers'
.get_drvinfo routines. While there clean-up some use of bare
constants and such.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the normal #defines not module specific ones.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This round of floor sweeping converts strncpy calls in various .get_drvinfo
routines to the preferred strlcpy. It also does a modicum of other
cleaning in those routines.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000 allocates a full page per skb fragment. We must account PAGE_SIZE
increments on skb->truesize, not the actual frag length.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per comments from Ben Hutchings on a previous patch, sweep the floors
a little removing unnecessary assignments of zero to fields of struct
ethtool_ringparam in driver code supporting ethtool -g.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The e1000 driver when running with lockdep could run into
some possible deadlocks between the work items acquiring
rtnl and the rtnl lock being acquired before work items
were cancelled.
Use a private mutex to make sure lock ordering isn't violated.
The private mutex is only used to protect areas not generally
covered by the rtnl lock already.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the previous commit, there are several functions
that are only ever called from thread context, and are
able to sleep with msleep instead of mdelay.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Thomas Gleixner (tglx) reported that e1000 was delaying for many milliseconds
(using mdelay) from inside timer/interrupt context. None of these paths are
performance critical and can be moved into threads/work items. This patch
implements the work items and the next patch changes the mdelays to msleeps.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Doing an 'ifconfig ethN down' followed by an 'ifconfig ethN up' on a qemu-kvm
guest system configured with two e1000 NICs can result in an 'unable to handle
kernel paging request at 0000000100000000' or 'bad page map in process ...' or
something similar.
These result from a 4096-byte page being corrupted with the following two-word
pattern (16-bytes) repeated throughout the entire page:
0x0000000000000000
0x0000000100000000
There can be other bits set as well. What is a constant is that the 2nd word
has the 32nd bit set. So one could see:
:
0x0000000000000000
0x0000000100000000
0x0000000000000000
0x0000000172adc067 <<< bad pte
0x800000006ec60067
0x0000000700000040
0x0000000000000000
0x0000000100000000
:
Which came from from a process' page table I dumped out when the marked line
was seen as bad by print_bad_pte().
The repeating pattern represents the e1000's two-word receive descriptor:
struct e1000_rx_desc {
__le64 buffer_addr; /* Address of the descriptor's data buffer */
__le16 length; /* Length of data DMAed into data buffer */
__le16 csum; /* Packet checksum */
u8 status; /* Descriptor status */
u8 errors; /* Descriptor Errors */
__le16 special;
};
And the 32nd bit of the 2nd word maps to the 'u8 status' member, and
corresponds to E1000_RXD_STAT_DD which indicates the descriptor is done.
The corruption appears to result from the following...
. An 'ifconfig ethN down' gets us into e1000_close(), which through a number
of subfunctions results in:
1. E1000_RCTL_EN being cleared in RCTL register. [e1000_down()]
2. dma_free_coherent() being called. [e1000_free_rx_resources()]
. An 'ifconfig ethN up' gets us into e1000_open(), which through a number of
subfunctions results in:
1. dma_alloc_coherent() being called. [e1000_setup_rx_resources()]
2. E1000_RCTL_EN being set in RCTL register. [e1000_setup_rctl()]
3. E1000_RCTL_EN being cleared in RCTL register. [e1000_configure_rx()]
4. RDLEN, RDBAH and RDBAL registers being set to reflect the dma page
allocated in step 1. [e1000_configure_rx()]
5. E1000_RCTL_EN being set in RCTL register. [e1000_configure_rx()]
During the 'ifconfig ethN up' there is a window opened, starting in step 2
where the receives are enabled up until they are disabled in step 3, in which
the address of the receive descriptor dma page known by the NIC is still the
previous one which was freed during the 'ifconfig ethN down'. If this memory
has been reallocated for some other use and the NIC feels so inclined, it will
write to that former dma page with predictably unpleasant results.
I realize that in the guest, we're dealing with an e1000 NIC that is software
emulated by qemu-kvm. The problem doesn't appear to occur on bare-metal. Andy
suspects that this is because in the emulator link-up is essentially instant
and traffic can start flowing immediately. Whereas on bare-metal, link-up
usually seems to take at least a few milliseconds. And this might be enough
to prevent traffic from flowing into the device inside the window where
E1000_RCTL_EN is set.
So perhaps a modification needs to be made to the qemu-kvm e1000 NIC emulator
to delay the link-up. But in defense of the emulator, it seems like a bad idea
to enable dma operations before the address of the memory to be involved has
been made known.
The following patch no longer enables receives in e1000_setup_rctl() but leaves
them however they were. It only enables receives in e1000_configure_rx(), and
only after the dma address has been made known to the hardware.
There are two places where e1000_setup_rctl() gets called. The one in
e1000_configure() is followed immediately by a call to e1000_configure_rx(), so
there's really no change functionally (except for the removal of the problem
window. The other is in __e1000_shutdown() and is not followed by a call to
e1000_configure_rx(), so there is a change functionally. But consider...
. An 'ifconfig ethN down' (just as described above).
. A 'suspend' of the system, which (I'm assuming) will find its way into
e1000_suspend() which calls __e1000_shutdown() resulting in:
1. E1000_RCTL_EN being set in RCTL register. [e1000_setup_rctl()]
And again we've re-opened the problem window for some unknown amount of time.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Virtual Machines with emulated e1000 network adapter running on Parallels'
server were seeing kernel panics due to the e1000 driver dereferencing an
unexpected NULL pointer retrieved from buffer_info->skb.
The problem has been addressed for the e1000e driver, but not for the e1000.
Since the two drivers share similar code in the affected area, a port of the
following e1000e driver commit solves the issue for the e1000 driver:
commit 9ed318d546
Author: Tom Herbert <therbert@google.com>
Date: Wed May 5 14:02:27 2010 +0000
e1000e: save skb counts in TX to avoid cache misses
In e1000_tx_map, precompute number of segements and bytecounts which
are derived from fields in skb; these are stored in buffer_info. When
cleaning tx in e1000_clean_tx_irq use the values in the associated
buffer_info for statistics counting, this eliminates cache misses
on skb fields.
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use IFF_UNICAST_FTL to find out if driver handles unicast address
filtering. In case it does not, promisc mode is entered.
Patch also fixes following drivers:
stmmac, niu: support uc filtering and yet it propagated
ndo_set_multicast_list
bna, benet, pxa168_eth, ks8851, ks8851_mll, ksz884x : has set
ndo_set_rx_mode but do not support uc filtering
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moves the Intel wired LAN drivers into drivers/net/ethernet/intel/ and
the necessary Kconfig and Makefile changes.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
