If posted write failed, an "Unhandled interrupt(s) 0x00000100" message
was logged by mistake.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After PM suspend + resume, the local configuration ROM was not restored.
This prevented remote nodes from recognizing the resuming machine.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Pull this define out of drivers/ieee1394/ohci1394.c and rename to match
other PCI class defines.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=7431
iBook G3 threw a machine check exception and put the display backlight
to full brightness after ohci1394 was unloaded and reloaded.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
- correct thinko in one of my last commits: cannot use PRINT macro with
ohci == NULL
- add log messages on ohci == NULL and on pci_enable_device != 0
- update log macros from patch "revert fail on error in suspend" to use
PRINT and DBGMSG where possible
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Some errors during preparation for suspended state can be skipped with a
warning instead of a failure of the whole suspend transition, notably an
error in pci_set_power_state.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Reorder the definitions of ohci1394_pci_suspend and _resume. Remove
redundant comments. Beautify return statements.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
I did a quick shot on what I described and the appended patch
does the first thing needed for working suspend/resume
in ohci1394 which is HW de- and re-initialisation.
It works with suspend2disk on my Ricoh R5C552 IEEE 1394 Controller
with the 2.6.17 kernel to the extent that if I call dvgrab --interactive
after suspend2disk without unloading ohci1394, it does not lock up
dvgrab with 100% CPU but properly connects to the camera, given
that I first unplug and plug the camera after coming back from
suspend.
I guess that could be fixed by forcing a bus reset in the resume
function.
I cannot test suspend to RAM here at the moment and should
follow the guidelines in Documentation/power/pci.txt also,
so this is rather a quick report than a finished patch and
there are some rough edges:
However, with this patch, I have to unload at least some in-kernel
users of ohci1394 like dv1394 or video1394 before suspending.
Not doing that caused an Oops and a bad tasklet error, probably from
not handling ISO tasklets during suspend/resume properly.
Maybe these can be temporarily cleared or unregistered and
re-registered for suspend/resume with help from the other
layers or from the highlevel 1394 core, but I do not really
know what these do.
But this patch provides a useful base to start from and is
already of much help for people which do not need dv1394
and video1394 or can unload them at least during suspend.
I cannot test function with sbp2 at the moment, but raw1394
seems to work fine.
Signed-off-by: Bernhard Kaindl <bk@fsfe.org>
Update 1: merge with previous two ohci1394 suspend/resume patches
Update 2: version for application on top of Linux 2.6.19-rc4
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
SLAB_KERNEL is an alias of GFP_KERNEL.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some errors during preparation for suspended state can be skipped with a
warning instead of a failure of the whole suspend transition, notably an
error in pci_set_power_state.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Put firewire host controller in PCI Dx state for system suspend.
(I was not able to measure any power savings, but it sounds like right
thing to do, anyway.)
Signed-off-by: Pavel Machek <pavel@suse.cz>
Update by stefanr: Shuffle with existing PPC_PMAC code. Set power
state in the resume hook too.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Rename ohci1394's packet_swab to header_le32_to_cpu to better reflect
what it actually does. Also, define a constant array as 'const' and
check the array index properly.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The transaction labels were misprinted int the debug printk "Packet
received from node..." due two byte-swapping once too often. Affected
were big endian machines, except UniNorth based ones. Fix tested by
Wolfgang Pfeiffer.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Remove some code which is unneeded if CONFIG_PM=n.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
A deactivated macro, defined as "#define foo(bar)", will result in
silent corruption if somebody forgets a semicolon after a call to foo.
Replace it by "#define foo(bar) do {} while (0)" which will reveal any
respective syntax errors.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This makes debugging with firescope easier.
Signed-off-by: Andi Kleen <ak@suse.de> (original patch)
Update:
- no need for #ifdef MODULE
- add comment in ieee1394_core, more verbose comment in ohci1394
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (update)
Recently a patch was added for preliminary suspend/resume handling on
!PPC_PMAC. However, this broke both suspend and firewire on powerpc
because it saves the pci state after the device has already been disabled.
This moves the save state to before the pmac specific code.
Signed-off-by: Danny Tholen <obiwan@mailmij.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ben Collins <bcollins@ubuntu.com>
Cc: Jody McIntyre <scjody@modernduck.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/bcollins/linux1394-2.6: (28 commits)
eth1394: replace __constant_htons by htons
ieee1394: adjust code formatting in highlevel.c
ieee1394: hl_irqs_lock is taken in hardware interrupt context
ieee1394_core: switch to kthread API
ieee1394: sbp2: Kconfig fix
ieee1394: add preprocessor constant for invalid csr address
sbp2: fix deregistration of status fifo address space
[PATCH] eth1394: endian fixes
Fix broken suspend/resume in ohci1394
sbp2: use __attribute__((packed)) for on-the-wire structures
sbp2: provide helptext for CONFIG_IEEE1394_SBP2_PHYS_DMA and mark it experimental
Update feature removal of obsolete raw1394 ISO requests.
sbp2: fix S800 transfers if phys_dma is off
sbp2: remove ohci1394 specific constant
ohci1394: make phys_dma parameter read-only
ohci1394: set address range properties
ieee1394: extend lowlevel API for address range properties
sbp2: log number of supported concurrent logins
sbp2: remove manipulation of inquiry response
ieee1394: save RAM by using a single tlabel for broadcast transactions
...
This ugly hack was long overdue to die.
It was a way to print out Sparc interrupts in a more freindly format,
since IRQ numbers were arbitrary opaque 32-bit integers which vectored
into PIL levels. These 32-bit integers were not necessarily in the
0-->NR_IRQS range, but the PILs they vectored to were.
The idea now is that we will increase NR_IRQS a little bit and use a
virtual<-->real IRQ number mapping scheme similar to PowerPC.
That makes this IRQ printing hack irrelevant, and furthermore only a
handful of drivers actually used __irq_itoa() making it even less
useful.
Signed-off-by: David S. Miller <davem@davemloft.net>
I've been experimenting to track down the cause of suspend/resume problems
on my Compaq Presario X1050 laptop:
http://bugzilla.kernel.org/show_bug.cgi?id=6075
Essentially the ACPI Embedded Controller and keyboard controller would
get into a bizarre, confused state after resume.
I found that unloading the ohci1394 module before suspend and reloading it
after resume made the problem go away. Diffing the dmesg output from
resume, with and without the module loaded, I found that with the module
loaded I was missing these:
PM: Writing back config space on device 0000:02:00.0 at offset 1. (Was 2100080, writing 2100007)
PM: Writing back config space on device 0000:02:00.0 at offset 3. (Was 0, writing 8008)
PM: Writing back config space on device 0000:02:00.0 at offset 4. (Was 0, writing 90200000)
PM: Writing back config space on device 0000:02:00.0 at offset 5. (Was 1, writing 2401)
PM: Writing back config space on device 0000:02:00.0 at offset f. (Was 20000100, writing 2000010a)
The default PCI driver performs the pci_restore_state when no driver is
loaded for the device. When the ohci1394 driver is loaded, it is supposed
to do this, however it appears not to do so.
I created the patch below and tested it, and it appears to resolve the
suspend problems I was having with the module loaded. I only added in the
pci_save_state and pci_restore_state - however, though I know little of
this hardware, surely the driver should really be doing more than this when
suspending and resuming? Currently it does almost nothing, what if there
are commands in progress, etc?
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Cc: Jody McIntyre <scjody@modernduck.com>
Cc: Ben Collins <bcollins@debian.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Being able to switch physical DMA on and off at run time would be a nice
feature but a PITA to support by highlevel drivers and userspace apps.
Therefore allow it only to be set when the driver is being loaded.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
This patch supplies the API extension introduced by patch
"ieee1394: extend lowlevel API for address range properties"
with proper addresses.
Like in patch ''ohci1394, sbp2: fix "scsi_add_device failed"
with PL-3507 based devices'', 1 TeraByte is chosen as physical
upper bound. This leaves a window for the middle address range.
This choice is only relevant for adapters which actually have a
programmable pysical upper bound register. (Only ALi and
Fujitsu adapters are known for this. Most adapters have a fixed
bound at 4 GB.) The middle address range is suitable for posted
writes.
AFAIK, PCILynx does not support physical DMA nor posted writes,
therefore no equivalent change in the pcilynx driver is necessary.
There is also a driver for GP2Lynx, although not in mainline Linux.
I assume this hardware does not support these OHCI features either.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
This patch modifies the ohci1394.c file to enable and manage the "cycle too
long" interrupt.
If this interrupt occurs, the "LinkControl.CycleMaster" bit of the host
controller is reseted. This implies, that the host controller does not send
"cycle start" packet anymore freezing then the isochronous communication.
The management of the interrupt added by the patch is that when the interrupt
occurs, the OHCI irq handler prints a kernel log warning and then sets the
"LinkControl.CycleMaster" bit again resuming the isochronous communication.
Signed-off-by: Jean-Baptiste Mur <jeanbaptiste@maunakeatech.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
spotted by Adrian Bunk. Also remove some superfluous comments.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Re-enable posted writes for status FIFO.
Besides bringing back a very minor bandwidth tweak from Linux 2.6.15.x
and older, this also fixes an interoperability regression since 2.6.16:
http://bugzilla.kernel.org/show_bug.cgi?id=6356
(sbp2: scsi_add_device failed. IEEE1394 HD is not working anymore.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Vanei Heidemann <linux@javanei.com.br>
Tested-by: Martin Putzlocher <mputzi@gmx.de> (chip type unconfirmed)
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (67 commits)
[PATCH] powerpc: Remove oprofile spinlock backtrace code
[PATCH] powerpc: Add oprofile calltrace support to all powerpc cpus
[PATCH] powerpc: Add oprofile calltrace support
[PATCH] for_each_possible_cpu: ppc
[PATCH] for_each_possible_cpu: powerpc
[PATCH] lock PTE before updating it in 440/BookE page fault handler
[PATCH] powerpc: Kill _machine and hard-coded platform numbers
ppc: Fix compile error in arch/ppc/lib/strcase.c
[PATCH] git-powerpc: WARN was a dumb idea
[PATCH] powerpc: a couple of trivial compile warning fixes
powerpc: remove OCP references
powerpc: Make uImage default build output for MPC8540 ADS
powerpc: move math-emu over to arch/powerpc
powerpc: use memparse() for mem= command line parsing
ppc: fix strncasecmp prototype
[PATCH] powerpc: make ISA floppies work again
[PATCH] powerpc: Fix some initcall return values
[PATCH] powerpc: Workaround for pSeries RTAS bug
[PATCH] spufs: fix __init/__exit annotations
[PATCH] powerpc: add hvc backend for rtas
...
This warning happens in practice because the resource length reported by
the chipset is too large. This is not actually a problem, so don't warn
about it. If it happens to be too small, warn about that, but with
a different message so people who are used to ignoring the old message
don't.
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
Various cleanups of how ohci1394 programs AsynchronousRequestFilter,
PhysicalRequestFilter, and physUpperBoundOffset. In particular, do not
rewrite registers within the bus reset interrupt handler if bus resets
do not affect the registers in the first place.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
This removes statically assigned platform numbers and reworks the
powerpc platform probe code to use a better mechanism. With this,
board support files can simply declare a new machine type with a
macro, and implement a probe() function that uses the flattened
device-tree to detect if they apply for a given machine.
We now have a machine_is() macro that replaces the comparisons of
_machine with the various PLATFORM_* constants. This commit also
changes various drivers to use the new macro instead of looking at
_machine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Print the number of IR and IT contexts which a hardware implements
as an informational log message when ohci1394 initializes.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
Their version information is not trustworthy.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@modernduck.com>
Changes all spinlocks that can be held during an irq handler to disable
interrupts while the lock is held. Changes spin_[un]lock_irq to use the
irqsave/irqrestore variants for robustness and readability.
In raw1394.c:handle_iso_listen(), don't grab host_info_lock at all -- we're
not accessing host_info_list or host_count, and holding this lock while
trying to tasklet_kill the iso tasklet this can cause an ABBA deadlock if
ohci:dma_rcv_tasklet is running and tries to grab host_info_lock in
raw1394.c:receive_iso. Test program attached reliably deadlocks all SMP
machines I have been able to test without this patch.
Signed-off-by: Andy Wingo <wingo@pobox.com>
Acked-by: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
