Add support for MICREL KSZ8795CLX Integrated 5-Port, 10-/100-Managed
Ethernet Switch with Gigabit GMII/RGMII and MII/RMII interfaces.
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare creating SPI reads and writes for other switch families.
The KS8995 family uses the straight forward
<8bit CMD><8bit ADDR>
sequence.
To be able to support KSZ8795 family, which uses
<3bit CMD><12bit ADDR><1 bit TR>
make the SPI command creation chip variant dependent.
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using device tree it is no more possible to reset the PHY at board
level. Furthermore, doing in the driver allows to power down the switch
when it is not used any more.
The patch introduces a new optional property "reset-gpios" denoting an
appropriate GPIO handle, e.g.:
reset-gpios = <&gpio0 46 GPIO_ACTIVE_LOW>
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the chip variant is now determined by spi_device_id, verify
family and chip id and determine the revision id.
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor to use spi_device_id table to facilitate easy
extendability.
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate higher order pages when pagesize is small, this will
reduce number of calls to page allocator and wastage of memory.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of OF device tree, the firmware information is attached to
the BGX device structure in the standard manner, so use the firmware
iterators and accessors where possible.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This affinity hint can be used by user space irqbalance tool to set
preferred CPU mask for irqs registered by this VF. Irqbalance needs
to be in 'exact' mode to set irq affinity same as indicated by
affinity hint.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_schedule is being called from hard irq context, hence
switch to napi_schedule_irqoff which avoids unneeded call
to local_irq_save and local_irq_restore.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When system is low on atomic memory, too many error messages are logged.
Since this is not a total failure but a simple switch to non-atomic allocation
better to have a stat.
Also add a stat for reset, kicked due to transmit watchdog timeout.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace 'goto' with 'return' to remove unnecessary check at label:
err_undo_flags.
The reason is that 'err_undo_flags' do two things for the first slave device:
1.revert bond mac address if it is set by the slave device.
2.revert bond device type if it's not ARPHRD_ETHER.
It's not necessary for the following three places, they changed neither bond
mac address nor type. It's straightforward to return directly.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested on Acqua A5 SoM (http://www.acmesystems.it/acqua).
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
32 bit systems using 'struct timeval' will break in the year 2038, so
we replace the code appropriately. However, this driver is not broken
in 2038 since we are only using microseconds portion of the time.
This patch replaces 'struct timeval' with 'struct timespec64'. We only
need to find elapsed microseconds rather than absolute time, so it's
better to use monotonic time, so using ktime_get_ts64() makes the code
more efficient and more robust against concurrent settimeofday()
calls.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Thomas Sailer <t.sailer@alumni.ethz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value of kzalloc on failure of allocation of memory should
be -ENOMEM and not -1.
Found using Coccinelle. A simplified version of the semantic patch
used is:
//<smpl>
@@
expression *e;
@@
e = kzalloc(...);
if (e == NULL) {
...
return
- -1
+ -ENOMEM
;
}
//</smpl>
The single call site only checks that the return value is not 0,
hence no change is required at the call site.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Adding NETIF_F_TSO6 feature flag;
2. Adding NETIF_F_HW_CSUM. NETIF_F_IPV6_CSUM and NETIF_F_IP_CSUM are
being deprecated;
3. Cleanup the coding style of flag assignment by using macro.
Signed-off-by: Simon Xiao <sixiao@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series provides support for iWARP applications to specify a TOS
value and have that map to a VLAN Priority for iw_cxgb4 iWARP connections.
In iw_cxgb4, when allocating an L2T entry, pass the skb_priority based
on the tos value in the cm_id. Also pass the correct tos value during
connection setup so the passive side gets the client's desired tos.
When sending the FLOWC work request to FW, if the egress device is
in a vlan, then use the vlan priority bits as the scheduling class.
This allows associating RDMA connections with scheduling classes to
provide traffic shaping per flow.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unmap initial buffer on error.
Don't free skb until it has been unmapped.
Move cbd_bufaddr assignment closer to the mapping function.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If you don't own it, you shouldn't write to it.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the interrupt routine processes this condition.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for complex macros every time we need to activate
a queue. Also, no need to call skb_get_queue_mapping when we already
know which queue it is using.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When first initialized, cur_tx points to the 1st
entry in the queue, and dirty_tx points to the last.
At this point, fec_enet_get_free_txdesc_num will
return tx_ring_size -2. If tx_ring_size -2 entries
are now queued, then fec_enet_get_free_txdesc_num
should return 0, but it returns tx_ring_size instead.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On an overrun, the other flags are not
valid, so don't check them.
Also, don't pass bad frames up the stack.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting the FTRL register will stop the fec from
trying to use multiple receive buffers.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to require the bond down while changing these settings, the change
will be reflected immediately and the 3ad mode will sort itself out.
For faster convergence set port->ntt to true in order to generate new
LACPDUs immediately.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From FW version 11.0. onwards, the PORT_MISCONFIG event generated by the FW
will carry more information about the event in the "data_word1"
and "data_word2" fields. This patch adds support in the driver to parse the
new information and log it accordingly. This patch also changes some of the
messages that are being logged currently.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we request RSS capability even if a single Rx ring is created.
As a result in few cases we unnecessarily consume an RSS capable interface
which is a limited resource in the chip.
This patch enables RSS on an interface only if more than one Rx ring
is created.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the unused code of sxgbe_xpcs.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Cc: Byungho An <bh74.an@samsung.com>
Cc: Girish K S <ks.giri@samsung.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1601191918470.2531@hadrien
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver has often repeated pattern of reading a register, AND'ing and/or
OR'ing some bits and writing the value back. Factor the pattern out into
sh_eth_modify() -- this saves 84 bytes of code with ARM gcc 4.7.3.
While at it, update Cogent Embedded's copyright.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver has often repeated pattern of reading a register, AND'ing and/or
OR'ing some bits and writing the value back. Factor the pattern out into
ravb_modify() -- this saves 260 bytes of code with ARM gcc 4.7.3.
While at it, update Cogent Embedded's copyrights.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the bonding allows to set ad_actor_system and prio while the
bond device is down, but these are actually applied only if there aren't
any slaves yet (applied to bond device when first slave shows up, and to
slaves at 3ad bind time). After this patch changes are applied immediately
and the new values can be used/seen after the bond's upped so it's not
necessary anymore to release all and enslave again to see the changes.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove some redudant brackets, use sizeof(*) instead of sizeof(struct x).
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the user to set and retrieve speed and duplex of the
virtio_net device via ethtool. Having this functionality is very helpful
for simulating different environments and also enables the virtio_net
device to participate in operations where proper speed and duplex are
required (e.g. currently bonding lacp mode requires full duplex). Custom
speed and duplex are not allowed, the user-supplied settings are validated
before applying.
Example:
$ ethtool eth1
Settings for eth1:
...
Speed: Unknown!
Duplex: Unknown! (255)
$ ethtool -s eth1 speed 1000 duplex full
$ ethtool eth1
Settings for eth1:
...
Speed: 1000Mb/s
Duplex: Full
Based on a patch by Roopa Prabhu.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use sunvnet perf trace macros to monitor LDC message exchange state.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows userspace to have direct access to VRF table association
versus looking up master device and its table.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My recent patch to the Xen Project documents a protocol for 'dynamic
multicast control' in netif.h. This extends the previous multicast control
protocol to not require a shared ring reconnection to turn the feature off.
Instead the backend watches the "request-multicast-control" key in xenstore
and turns the feature off if the key value is written to zero.
This patch adds support for dynamic multicast control in xen-netback.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupt moderation parameters need to be recalculated only
after a time interval of 1 ms. Interval calculation is wrong
when there is a rollover of jiffies. Using recommended way of interval
calculation using jiffies to fix this.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retry error recovery MAX_ERR_RECOVERY_RETRY_COUNT times in case of
failure during error recovery.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After error is detected, wait for adapter to move to ready state
before destroying queues and cleanup of other resources. Also
skip performing any cleanup for non-Lancer chips and move debug
messages to correct routine.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CMD_SUBSYSTEM_LOWLEVEL cmds need DEV_CFG Privilege to run
which VFs don't have by default.
Self-tests need to be issued only for PFs.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SRIOV resource distribution logic for RX/TX queue counts is not optimal
when a small number of VFs are enabled. It does not take into account the
VF's EQ count while computing the queue counts. Because of this, the VF
gets a large number of queues, though it doesn't have sufficient EQs,
resulting in wasted queue resources. And the PF gets a smaller share of
queues though it has more EQs. Fix this by capping the VF queue count at
its EQ count.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver decrements its vlan count without checking if it is really
present in its list. This results in an invalid vlan count and impacts
subsequent vlan add/rem ops. The function be_vlan_rem_vid() should be
updated to fix this.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently logs the message "VF is not privileged to issue
opcode" by checking only the base_status field for UNAUTHORIZED_REQUEST.
Add check to look for INSUFFICIENT_PRIVILEGES in the additional status
field also as not all cmds fail with that base status.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be_set_phys_id() returns 0 to ethtool when the command fails in the FW.
This patch fixes the set_phys_id() to return -EIO in case the FW cmd fails.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a lot of code duplication. Factor out the duplicate code to a new
function shared between IPv4 and IPv6 xmit path.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag for tx checksumming for tunneling over IPv4 and IPv6 is different.
Decide whether to do tx checksumming in vxlan_xmit_one and pass it on as
a separate flag. This will allow for tx path consolidation in the next
patch.
Unfortunately, gcc is not clever enough to see that udp_sum is always
initialized and gives an uninitialized variable warning. Set it to false to
silence the warning.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
