The peer param id for PEER_PARAM_USE_FIXED_PWR
is different for tlv and non-tlv firmware. This
causes incorrect peer param to be set by the driver
to the firmware(tlv/non-tlv).
Create seperate peer param map for tlv and non-tlv
firmware and attach the peer param id based on the
firmware type during the init.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
MSA memory region caries the hw descriptors information.
Dump MSA region in core dump as this is very helpful in debugging
hw issues.
Testing: Tested on WCN3990 HW
Tested FW: WLAN.HL.3.1-00959-QCAHLSWMTPLZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
PMIC XO is the clock source for wifi rf clock in integrated wifi
chipset ex: WCN3990. Due to board layout errors XO frequency drifts
can cause wifi rf clock inaccuracy.
XO calibration test tree in Factory Test Mode is used to find the
best frequency offset(for example +/-2KHz )by programming XO trim
register. This ensure system clock stays within required 20 ppm
WLAN rf clock.
Retrieve the xo trim offset via system firmware (e.g., device tree),
especially in the case where the device doesn't have a useful EEPROM
on which to store the calibrated XO offset (e.g., for integrated Wifi).
Calibrated XO offset is sent to fw, which compensate the clock drift
by programing the XO trim register.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a spelling mistake in a ath10k_warn warning message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bad latency is found on QCA988x, the issue was introduced by
commit 4504f0e5b5 ("ath10k: sdio: workaround firmware UART
pin configuration bug"). If uart_pin_workaround is false, this
change will set uart pin even if uart_print is false.
Tested HW: QCA9880
Tested FW: 10.2.4-1.0-00037
Fixes: 4504f0e5b5 ("ath10k: sdio: workaround firmware UART pin configuration bug")
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If 'sta->tdls' is false, no cleanup is executed, leading to memory/resource
leaks, e.g., 'arsta->tx_stats'. To fix this issue, perform cleanup before
go to the 'exit' label.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
driver sends QMI_WLFW_MSA_INFO_REQ_V01 QMI request to firmware
and in response expects range of addresses and size to be mapped.
Add condition to check whether addresses in response falls
under valid range otherwise return failure.
Testing: Tested on WCN3990 HW
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use ath10k_pci_soc_read32 / ath10k_pci_soc_write32 functions for
the rest of warm_reset functions. Until now these have been used
only for ath10k_pci_warm_reset_si0, but since they already exist
it makes sense to simplify code a bit.
Runtime tested with QCA9862.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_bss_info_changed() handles various events from the upper layers. It
parses the changed bitfield and then configures the driver/firmware
accordingly. Each detected event is handled in a separate scope which is
independent of each other - but in the same function.
The commit f279294e9e ("ath10k: add support for configuring management
packet rate") changed this behavior by returning from this function
prematurely when some precondition was not fulfilled. All new event
handlers added after the BSS_CHANGED_BASIC_RATES event handler would then
also be skipped.
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
No frequency is currently specified for the single clock defined in the
snoc driver, so the clock wrappers reimplements the standard bulk API
provided by the clock framework. Change to this.
The single clock defined is marked as optional so this version of the
get API is used, but might need to be reconsidered in the future.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regulator_get_optional() exists for cases where the driver needs do
behave differently depending on some regulator supply being present or
not, as we don't use this we can use the standard regulator_get() and
rely on its handling of unspecified regulators.
While the driver currently doesn't specify any loads the regulator
framework was updated last year to only account for load of enabled
regulators, so should the need appear it's better to apply load numbers
during initialization that dynamically.
With this the regulator wrappers have been reduced the become identical
to the standard bulk API provided by the regulator framework, so use
these instead of rolling our own.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regulator operations is trying to set a voltage to a fixed value, by
giving some wiggle room. But some board designs specifies regulator
voltages outside this limited range. One such example is the Lenovo Yoga
C630, with vdd-3.3-ch0 in particular specified at 3.1V.
But consumers with fixed voltage requirements should just rely on the
board configuration to provide the power at the required level, so this
code should be removed.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The introduction of 768ec4c012 ("ath10k: update HOST capability QMI
message") served the purpose of supporting the new and extended HOST
capability QMI message.
But while the new message adds a slew of optional members it changes the
data type of the "daemon_support" member, which means that older
versions of the firmware will fail to decode the incoming request
message.
There is no way to detect this breakage from Linux and there's no way to
recover from sending the wrong message (i.e. we can't just try one
format and then fallback to the other), so a quirk is introduced in
DeviceTree to indicate to the driver that the firmware requires the 8bit
version of this message.
Cc: stable@vger.kernel.org
Fixes: 768ec4c012 ("ath10k: update HOST capability qmi message")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking fixes from David Miller:
1) Don't corrupt xfrm_interface parms before validation, from Nicolas
Dichtel.
2) Revert use of usb-wakeup in btusb, from Mario Limonciello.
3) Block ipv6 packets in bridge netfilter if ipv6 is disabled, from
Leonardo Bras.
4) IPS_OFFLOAD not honored in ctnetlink, from Pablo Neira Ayuso.
5) Missing ULP check in sock_map, from John Fastabend.
6) Fix receive statistic handling in forcedeth, from Zhu Yanjun.
7) Fix length of SKB allocated in 6pack driver, from Christophe
JAILLET.
8) ip6_route_info_create() returns an error pointer, not NULL. From
Maciej Żenczykowski.
9) Only add RDS sock to the hashes after rs_transport is set, from
Ka-Cheong Poon.
10) Don't double clean TX descriptors in ixgbe, from Ilya Maximets.
11) Presence of transmit IPSEC offload in an SKB is not tested for
correctly in ixgbe and ixgbevf. From Steffen Klassert and Jeff
Kirsher.
12) Need rcu_barrier() when register_netdevice() takes one of the
notifier based failure paths, from Subash Abhinov Kasiviswanathan.
13) Fix leak in sctp_do_bind(), from Mao Wenan.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (72 commits)
cdc_ether: fix rndis support for Mediatek based smartphones
sctp: destroy bucket if failed to bind addr
sctp: remove redundant assignment when call sctp_get_port_local
sctp: change return type of sctp_get_port_local
ixgbevf: Fix secpath usage for IPsec Tx offload
sctp: Fix the link time qualifier of 'sctp_ctrlsock_exit()'
ixgbe: Fix secpath usage for IPsec TX offload.
net: qrtr: fix memort leak in qrtr_tun_write_iter
net: Fix null de-reference of device refcount
ipv6: Fix the link time qualifier of 'ping_v6_proc_exit_net()'
tun: fix use-after-free when register netdev failed
tcp: fix tcp_ecn_withdraw_cwr() to clear TCP_ECN_QUEUE_CWR
ixgbe: fix double clean of Tx descriptors with xdp
ixgbe: Prevent u8 wrapping of ITR value to something less than 10us
mlx4: fix spelling mistake "veify" -> "verify"
net: hns3: fix spelling mistake "undeflow" -> "underflow"
net: lmc: fix spelling mistake "runnin" -> "running"
NFC: st95hf: fix spelling mistake "receieve" -> "receive"
net/rds: An rds_sock is added too early to the hash table
mac80211: Do not send Layer 2 Update frame before authorization
...
Last set of patches for 5.4. wil6210 and rtw88 being most active this
time, but ath9k also having a new module to load devices without
EEPROM.
Major changes:
wil6210
* add support for Enhanced Directional Multi-Gigabit (EDMG) channels 9-11
* add debugfs file to show PCM ring content
* report boottime_ns in scan results
ath9k
* add a separate loader for AR92XX (and older) pci(e) without eeprom
brcmfmac
* use the same wiphy after PCIe reset to not confuse the user space
rtw88
* enable interrupt migration
* enable AMSDU in AMPDU aggregation
* report RX power for each antenna
* enable to DPK and IQK calibration methods to improve performance
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdfLwvAAoJEG4XJFUm622b8N8H/141YVGazqoNC/l0kaMbWZ//
xbgdS8ujGyEFg86dfXs1DjYPsPG1v+UJwc42GQALcjVrdUacuO7ZEdBKF6q9q0gG
7WsZrzmgMk2dJsZKSCYZHORbEJ/GE7yCgO1W1hS0iTRNXEV6/6u2s7bx4mPB3uhl
voYLTLaDvA2n8+pxuJ/Dl0ewWFuGnWqnhgU5CV3f9MGLkB4BXmvMdA5iqhiqq3Bj
RWfBZCslJj3snh4vsTzRNqnRRvtgTv3Nt/fVV8uH+K5wXBMutlc+MfVQw21kMb7c
RConz/N87usC+pgY+va2UpyNqLis2rUhb0UH4/Sqc7uBmeCBSyE8JulkRLnce+c=
=850h
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-09-14' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.4
Last set of patches for 5.4. wil6210 and rtw88 being most active this
time, but ath9k also having a new module to load devices without
EEPROM.
Major changes:
wil6210
* add support for Enhanced Directional Multi-Gigabit (EDMG) channels 9-11
* add debugfs file to show PCM ring content
* report boottime_ns in scan results
ath9k
* add a separate loader for AR92XX (and older) pci(e) without eeprom
brcmfmac
* use the same wiphy after PCIe reset to not confuse the user space
rtw88
* enable interrupt migration
* enable AMSDU in AMPDU aggregation
* report RX power for each antenna
* enable to DPK and IQK calibration methods to improve performance
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the fact that devlink reload failed is stored in drivers.
Move this flag into devlink core. Also, expose it to the user.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to properly implement failure indication during reload,
split the reload op into two ops, one for down phase and one for
up phase.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the function restart_one into two functions and separate teardown
and buildup.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A Mediatek based smartphone owner reports problems with USB
tethering in Linux. The verbose USB listing shows a rndis_host
interface pair (e0/01/03 + 10/00/00), but the driver fails to
bind with
[ 355.960428] usb 1-4: bad CDC descriptors
The problem is a failsafe test intended to filter out ACM serial
functions using the same 02/02/ff class/subclass/protocol as RNDIS.
The serial functions are recognized by their non-zero bmCapabilities.
No RNDIS function with non-zero bmCapabilities were known at the time
this failsafe was added. But it turns out that some Wireless class
RNDIS functions are using the bmCapabilities field. These functions
are uniquely identified as RNDIS by their class/subclass/protocol, so
the failing test can safely be disabled. The same applies to the two
types of Misc class RNDIS functions.
Applying the failsafe to Communication class functions only retains
the original functionality, and fixes the problem for the Mediatek based
smartphone.
Tow examples of CDC functional descriptors with non-zero bmCapabilities
from Wireless class RNDIS functions are:
0e8d:000a Mediatek Crosscall Spider X5 3G Phone
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x0f
connection notifications
sends break
line coding and serial state
get/set/clear comm features
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
and
19d2:1023 ZTE K4201-z
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
CDC Union:
bMasterInterface 0
bSlaveInterface 1
The Mediatek example is believed to apply to most smartphones with
Mediatek firmware. The ZTE example is most likely also part of a larger
family of devices/firmwares.
Suggested-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 5.4. Major changes:
wil6210
* add support for Enhanced Directional Multi-Gigabit (EDMG) channels 9-11
* add debugfs file to show PCM ring content
* report boottime_ns in scan results
ath9k
* add a separate loader for AR92XX (and older) pci(e) without eeprom,
enabled with the new ATH9K_PCI_NO_EEPROM Kconfig option
Report chains and chain_signal in ieee80211_rx_status.
It is useful for program such as tcpdump to see if the
antennas are well connected/placed.
8822C is able to receive CCK rates with 2 antennas, while
8822B can only use 1 antenna path to receive CCK rates.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix the wrong RF path for CCK rx power calculation.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92d_evm_db_to_percentage is functionally identical
to the generic version rtl_evm_db_to_percentage, so remove
_rtl92d_evm_db_to_percentage and use the generic version instead.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92c_evm_db_to_percentage is functionally identical
to the generic version rtl_evm_db_to_percentage, so remove
_rtl92c_evm_db_to_percentage and use the generic version instead.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92c_evm_db_to_percentage is functionally identical
to the generic version rtl_evm_db_to_percentage, so remove
_rtl92c_evm_db_to_percentage and use the generic version instead.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hardware has enough buffer to receive like 8K for an MPDU.
So tell mac80211 that we can receive AMSDU in AMPDU.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This mechanism reduces the numbers of false alram in cck rate by
dynamically adjusting the value of power threshold and cs_ratio.
We determine the new value by three factors, which are rssi, false alarm
count and igi. Based on these factors, we define the current condition
into five levels. Compared to the previous level, if the level is changed,
we set the new values for power threshold and cs_ratio.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since 8822c requires to do not only IQK, but also DPK.
Move these calibrations that need to be done once the channel
is determined, into phy_calibration.
And note that the order of the calibrations matters, 8822c
should do IQK first, then DPK.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Power amplifiers are not linear components, and require DPK to
reduce its nonlinearity. DPK is called Digital Pre-distortion
Calibration, can be used to compensate the output of power.
DPK tracking is in charge of tracking the thermal changes. And
it then shifts the power curve accordingly, which makes the
power output remains linear even if the PA works in different
temperature.
To perform DPK, the parameter table should also be updated.
And the table will be applied when device is powered on.
Then DPK will reference the values to calibrate.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for doing IQK in firmware
Ideally the RF component's I/Q vectors should be orthogonal,
but usually they are not. So we need to calibrate for the RF
components, ex. PA/LNA, ADC/DAC.
And if the I/Q vectors are more orthogonal, the mixed signal
will have less deviation. This helps with those rates with
higher modulation (MCS8-9), because they have more strict
EVM/SNR requirement. Also the better of the quality of the
signal, the longer it can propagate, and the better throughput
performance we can get.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable 8822C Tx/Rx interrupt migration.
In some platforms, performance test may cause heavy cpu loading and get
bad results. Interrupt migration can decrease the amount of interrupts,
and lower cpu loading.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
update sequence to v13 to reduce power consumption
when MAC power off
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Each of these drivers defines some device to host macros that are never
used, thus they can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl complains about a space after a cast
are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
iAs the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl reports lines too long are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With the commit e86dc1ca46 ("Libertas: cfg80211 support") we've lost
the ability to actually set the Mesh SSID from userspace.
NL80211_CMD_SET_INTERFACE with NL80211_ATTR_MESH_ID sets the mesh point
interface's ssid field. Let's use that one for the Libertas Mesh
operation
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Port the same fix for ixgbe to ixgbevf.
The ixgbevf driver currently does IPsec Tx offloading
based on an existing secpath. However, the secpath
can also come from the Rx side, in this case it is
misinterpreted for Tx offload and the packets are
dropped with a "bad sa_idx" error. Fix this by using
the xfrm_offload() function to test for Tx offload.
CC: Shannon Nelson <snelson@pensando.io>
Fixes: 7f68d43067 ("ixgbevf: enable VF IPsec offload operations")
Reported-by: Jonathan Tooker <jonathan@reliablehosting.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-09-12
This series contains updates to ice driver to implement and support
loading a Dynamic Device Personalization (DDP) package from lib/firmware
onto the device.
Paul updates the way the driver version is stored in the driver so that
we can pass the driver version to the firmware. Passing of the driver
version to the firmware is needed for the DDP package to ensure we have
the appropriate support in the driver for the features in the package.
Lukasz fixes how the firmware version is stored to align with how the
firmware stores its own version. Also extended the log message to
display additional useful information such as NVM version, API patch
information and firmware build hash.
Tony adds the needed driver support to check, load and store the DDP
package. Also add support for the ability to load DDP packages intended
for specific hardware devices, as well as what to do when loading of the
DDP package fails to load.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2019-09-11
This series contains updates to i40e, ixgbe/vf and iavf.
Wenwen Wang fixes a potential memory leak where 3 allocated variables
are not properly cleaned up on failure for ixgbe.
Stefan Assmann fixes a potential kernel panic found when repeatedly
spawning and destroying VFs in i40e when a NULL pointer is dereferenced
due to a race condition. Fixed up the i40e driver to clear the
__I40E_VIRTCHNL_OP_PENDING bit before returning after an invalid
minimum transmit rate is requested. Updates the iavf driver to only
apply the MAC address change when the PF ACK's the requested change.
Tonghao Zhang updates ixgbe to use the skb_get_queue_mapping() API call
instead of the driver accessing the queue mapping directly.
Jake updates i40e to use ktime_get_real_ts64() instead of
ktime_to_timespec64(). Removes the define for bit 0x0001 for cloud
filters, since it is a reserved bit and not a valid type. Also added
code comments to clearly state which bits are reserved and should not be
used or defined for cloud filter adminq command. Clarify the macros
used to specify the cloud filter fields are individual bits, so use the
BIT() macro.
Aleksandr fixes up the print_link_message() to include the "negotiated"
FEC status for i40e.
Czeslaw also adds additional log message for devices without FEC in the
print_link_message() for i40e.
Colin Ian King reduces the object code size by making the array API
static constant.
Magnus fixes a potential receive buffer starvation issue for AF_XDP by
kicking the NAPI context of any queue with an attached AF_XDP zero-copy
socket.
v2: Removed patch 11 from the original series (Alex Duyck's ITR fix),
so that it can be sent to the net tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
