Removale of skeleton.dtsi allows us also to fix the following
warning from the dts compiler:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
by adding proper unit addresses to the memory nodes.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
The 'compatible = "nxp,jc42"' binding only happened to work because
the Linux driver is named jc42. The driver now supports generic
bindings for JC-42 compatible chips, so use the generic binding instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Fix the following warnings from dtc by either adding or removing
the unit name from the node.
Warning (unit_address_vs_reg): Node /soc/flash-controller@40003000/flash@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /pca_buttons/button@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /pca_buttons/button@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /pca_buttons/button@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /pca_buttons/button@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /pca_buttons/button@4 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /pca_buttons/button@5 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /pca_buttons/button@6 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /pca_buttons/button@7 has a unit name, but no reg property
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Enable adc1 on LPC4350 Hitex Evalution board. This board has a
10k potensiometer (R26) connected to ADC1 channel 2.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Add the I2C0 bus and the some of the I2C devices on the Hitex
LPC4350 eval board.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
The Hitex LPC4350 eval board has a Spansion S25SL064P SPI-NOR Flash connected
to the SPIFI perherial.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Setup the emc pins used by external memory devices and add
configuration for the devices found on the Hitex eval board.
The Hitex eval board has a NOR Flash attached to chip select 0
and 512 kB of SRAM on chip select 2.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable Ethernet and add pin muxing and set the correct
frequency on the enet tx clock input.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Setup pin muxing and properties for the debug console on uart0.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add CGU and CCU clock-controller nodes for lpc18xx together with
the fixed input clocks. Also remove the temporary fixed-factor
pll1 clock from both lpc18xx and lpc4350-hitex-eval DTS now that
proper clock drivers are inplace.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Add basic support for Hitex LPC4350 Evaluation Board. Board
features a LPC4350 Soc, 8 MB SDRAM, 8 MB SPI Flash, USB and
Ethernet.
More information can be found on:
http://www.hitex.com/index.php?id=3212
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@gmail.com>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
