We introduce a feature that works like a combination of TCP_NAGLE and
TCP_CORK, but without some of the weaknesses of those. In particular,
we will not observe long delivery delays because of delayed acks, since
the algorithm itself decides if and when acks are to be sent from the
receiving peer.
- The nagle property as such is determined by manipulating a new
'maxnagle' field in struct tipc_sock. If certain conditions are met,
'maxnagle' will define max size of the messages which can be bundled.
If it is set to zero no messages are ever bundled, implying that the
nagle property is disabled.
- A socket with the nagle property enabled enters nagle mode when more
than 4 messages have been sent out without receiving any data message
from the peer.
- A socket leaves nagle mode whenever it receives a data message from
the peer.
In nagle mode, messages smaller than 'maxnagle' are accumulated in the
socket write queue. The last buffer in the queue is marked with a new
'ack_required' bit, which forces the receiving peer to send a CONN_ACK
message back to the sender upon reception.
The accumulated contents of the write queue is transmitted when one of
the following events or conditions occur.
- A CONN_ACK message is received from the peer.
- A data message is received from the peer.
- A SOCK_WAKEUP pseudo message is received from the link level.
- The write queue contains more than 64 1k blocks of data.
- The connection is being shut down.
- There is no CONN_ACK message to expect. I.e., there is currently
no outstanding message where the 'ack_required' bit was set. As a
consequence, the first message added after we enter nagle mode
is always sent directly with this bit set.
This new feature gives a 50-100% improvement of throughput for small
(i.e., less than MTU size) messages, while it might add up to one RTT
to latency time when the socket is in nagle mode.
Acked-by: Ying Xue <ying.xue@windreiver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, TIPC transports intra-node user data messages directly
socket to socket, hence shortcutting all the lower layers of the
communication stack. This gives TIPC very good intra node performance,
both regarding throughput and latency.
We now introduce a similar mechanism for TIPC data traffic across
network namespaces located in the same kernel. On the send path, the
call chain is as always accompanied by the sending node's network name
space pointer. However, once we have reliably established that the
receiving node is represented by a namespace on the same host, we just
replace the namespace pointer with the receiving node/namespace's
ditto, and follow the regular socket receive patch though the receiving
node. This technique gives us a throughput similar to the node internal
throughput, several times larger than if we let the traffic go though
the full network stacks. As a comparison, max throughput for 64k
messages is four times larger than TCP throughput for the same type of
traffic.
To meet any security concerns, the following should be noted.
- All nodes joining a cluster are supposed to have been be certified
and authenticated by mechanisms outside TIPC. This is no different for
nodes/namespaces on the same host; they have to auto discover each
other using the attached interfaces, and establish links which are
supervised via the regular link monitoring mechanism. Hence, a kernel
local node has no other way to join a cluster than any other node, and
have to obey to policies set in the IP or device layers of the stack.
- Only when a sender has established with 100% certainty that the peer
node is located in a kernel local namespace does it choose to let user
data messages, and only those, take the crossover path to the receiving
node/namespace.
- If the receiving node/namespace is removed, its namespace pointer
is invalidated at all peer nodes, and their neighbor link monitoring
will eventually note that this node is gone.
- To ensure the "100% certainty" criteria, and prevent any possible
spoofing, received discovery messages must contain a proof that the
sender knows a common secret. We use the hash mix of the sending
node/namespace for this purpose, since it can be accessed directly by
all other namespaces in the kernel. Upon reception of a discovery
message, the receiver checks this proof against all the local
namespaces'hash_mix:es. If it finds a match, that, along with a
matching node id and cluster id, this is deemed sufficient proof that
the peer node in question is in a local namespace, and a wormhole can
be opened.
- We should also consider that TIPC is intended to be a cluster local
IPC mechanism (just like e.g. UNIX sockets) rather than a network
protocol, and hence we think it can justified to allow it to shortcut the
lower protocol layers.
Regarding traceability, we should notice that since commit 6c9081a391
("tipc: add loopback device tracking") it is possible to follow the node
internal packet flow by just activating tcpdump on the loopback
interface. This will be true even for this mechanism; by activating
tcpdump on the involved nodes' loopback interfaces their inter-name
space messaging can easily be tracked.
v2:
- update 'net' pointer when node left/rejoined
v3:
- grab read/write lock when using node ref obj
v4:
- clone traffics between netns to loopback
Suggested-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk->sk_backlog.len can be written by BH handlers, and read
from process contexts in a lockless way.
Note the write side should also use WRITE_ONCE() or a variant.
We need some agreement about the best way to do this.
syzbot reported :
BUG: KCSAN: data-race in tcp_add_backlog / tcp_grow_window.isra.0
write to 0xffff88812665f32c of 4 bytes by interrupt on cpu 1:
sk_add_backlog include/net/sock.h:934 [inline]
tcp_add_backlog+0x4a0/0xcc0 net/ipv4/tcp_ipv4.c:1737
tcp_v4_rcv+0x1aba/0x1bf0 net/ipv4/tcp_ipv4.c:1925
ip_protocol_deliver_rcu+0x51/0x470 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5004
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5118
netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5208
napi_skb_finish net/core/dev.c:5671 [inline]
napi_gro_receive+0x28f/0x330 net/core/dev.c:5704
receive_buf+0x284/0x30b0 drivers/net/virtio_net.c:1061
virtnet_receive drivers/net/virtio_net.c:1323 [inline]
virtnet_poll+0x436/0x7d0 drivers/net/virtio_net.c:1428
napi_poll net/core/dev.c:6352 [inline]
net_rx_action+0x3ae/0xa50 net/core/dev.c:6418
read to 0xffff88812665f32c of 4 bytes by task 7292 on cpu 0:
tcp_space include/net/tcp.h:1373 [inline]
tcp_grow_window.isra.0+0x6b/0x480 net/ipv4/tcp_input.c:413
tcp_event_data_recv+0x68f/0x990 net/ipv4/tcp_input.c:717
tcp_rcv_established+0xbfe/0xf50 net/ipv4/tcp_input.c:5618
tcp_v4_do_rcv+0x381/0x4e0 net/ipv4/tcp_ipv4.c:1542
sk_backlog_rcv include/net/sock.h:945 [inline]
__release_sock+0x135/0x1e0 net/core/sock.c:2427
release_sock+0x61/0x160 net/core/sock.c:2943
tcp_recvmsg+0x63b/0x1a30 net/ipv4/tcp.c:2181
inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
sock_recvmsg_nosec net/socket.c:871 [inline]
sock_recvmsg net/socket.c:889 [inline]
sock_recvmsg+0x92/0xb0 net/socket.c:885
sock_read_iter+0x15f/0x1e0 net/socket.c:967
call_read_iter include/linux/fs.h:1864 [inline]
new_sync_read+0x389/0x4f0 fs/read_write.c:414
__vfs_read+0xb1/0xc0 fs/read_write.c:427
vfs_read fs/read_write.c:461 [inline]
vfs_read+0x143/0x2c0 fs/read_write.c:446
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 7292 Comm: syz-fuzzer Not tainted 5.3.0+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
sk_add_backlog() callers usually read sk->sk_rcvbuf without
owning the socket lock. This means sk_rcvbuf value can
be changed by other cpus, and KCSAN complains.
Add READ_ONCE() annotations to document the lockless nature
of these reads.
Note that writes over sk_rcvbuf should also use WRITE_ONCE(),
but this will be done in separate patches to ease stable
backports (if we decide this is relevant for stable trees).
BUG: KCSAN: data-race in tcp_add_backlog / tcp_recvmsg
write to 0xffff88812ab369f8 of 8 bytes by interrupt on cpu 1:
__sk_add_backlog include/net/sock.h:902 [inline]
sk_add_backlog include/net/sock.h:933 [inline]
tcp_add_backlog+0x45a/0xcc0 net/ipv4/tcp_ipv4.c:1737
tcp_v4_rcv+0x1aba/0x1bf0 net/ipv4/tcp_ipv4.c:1925
ip_protocol_deliver_rcu+0x51/0x470 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5004
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5118
netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5208
napi_skb_finish net/core/dev.c:5671 [inline]
napi_gro_receive+0x28f/0x330 net/core/dev.c:5704
receive_buf+0x284/0x30b0 drivers/net/virtio_net.c:1061
virtnet_receive drivers/net/virtio_net.c:1323 [inline]
virtnet_poll+0x436/0x7d0 drivers/net/virtio_net.c:1428
napi_poll net/core/dev.c:6352 [inline]
net_rx_action+0x3ae/0xa50 net/core/dev.c:6418
read to 0xffff88812ab369f8 of 8 bytes by task 7271 on cpu 0:
tcp_recvmsg+0x470/0x1a30 net/ipv4/tcp.c:2047
inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
sock_recvmsg_nosec net/socket.c:871 [inline]
sock_recvmsg net/socket.c:889 [inline]
sock_recvmsg+0x92/0xb0 net/socket.c:885
sock_read_iter+0x15f/0x1e0 net/socket.c:967
call_read_iter include/linux/fs.h:1864 [inline]
new_sync_read+0x389/0x4f0 fs/read_write.c:414
__vfs_read+0xb1/0xc0 fs/read_write.c:427
vfs_read fs/read_write.c:461 [inline]
vfs_read+0x143/0x2c0 fs/read_write.c:446
ksys_read+0xd5/0x1b0 fs/read_write.c:587
__do_sys_read fs/read_write.c:597 [inline]
__se_sys_read fs/read_write.c:595 [inline]
__x64_sys_read+0x4c/0x60 fs/read_write.c:595
do_syscall_64+0xcf/0x2f0 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 7271 Comm: syz-fuzzer Not tainted 5.3.0+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
__tipc_nl_compat_dumpit() calls tipc_nl_publ_dump() which expects
the attrs to be available by genl_dumpit_info(cb)->attrs. Add info
struct and attr parsing in compat dumpit function.
Reported-by: syzbot+8d37c50ffb0f52941a5e@syzkaller.appspotmail.com
Fixes: 057af70713 ("net: tipc: have genetlink code to parse the attrs during dumpit")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
As this is the last user of genl_family_attrbuf, convert to allocate
attrs locally and do it in a similar way this is done in compat_doit().
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benefit from the fact that the generic netlink code can parse the attrs
for dumpit op and avoid need to parse it in the op callback.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have identified a problem with the "oversubscription" policy in the
link transmission code.
When small messages are transmitted, and the sending link has reached
the transmit window limit, those messages will be bundled and put into
the link backlog queue. However, bundles of data messages are counted
at the 'CRITICAL' level, so that the counter for that level, instead of
the counter for the real, bundled message's level is the one being
increased.
Subsequent, to-be-bundled data messages at non-CRITICAL levels continue
to be tested against the unchanged counter for their own level, while
contributing to an unrestrained increase at the CRITICAL backlog level.
This leaves a gap in congestion control algorithm for small messages
that can result in starvation for other users or a "real" CRITICAL
user. Even that eventually can lead to buffer exhaustion & link reset.
We fix this by keeping a 'target_bskb' buffer pointer at each levels,
then when bundling, we only bundle messages at the same importance
level only. This way, we know exactly how many slots a certain level
have occupied in the queue, so can manage level congestion accurately.
By bundling messages at the same level, we even have more benefits. Let
consider this:
- One socket sends 64-byte messages at the 'CRITICAL' level;
- Another sends 4096-byte messages at the 'LOW' level;
When a 64-byte message comes and is bundled the first time, we put the
overhead of message bundle to it (+ 40-byte header, data copy, etc.)
for later use, but the next message can be a 4096-byte one that cannot
be bundled to the previous one. This means the last bundle carries only
one payload message which is totally inefficient, as for the receiver
also! Later on, another 64-byte message comes, now we make a new bundle
and the same story repeats...
With the new bundling algorithm, this will not happen, the 64-byte
messages will be bundled together even when the 4096-byte message(s)
comes in between. However, if the 4096-byte messages are sent at the
same level i.e. 'CRITICAL', the bundling algorithm will again cause the
same overhead.
Also, the same will happen even with only one socket sending small
messages at a rate close to the link transmit's one, so that, when one
message is bundled, it's transmitted shortly. Then, another message
comes, a new bundle is created and so on...
We will solve this issue radically by another patch.
Fixes: 365ad353c2 ("tipc: reduce risk of user starvation during link congestion")
Reported-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The policy for handling the skb list locks on the send and receive paths
is simple.
- On the send path we never need to grab the lock on the 'xmitq' list
when the destination is an exernal node.
- On the receive path we always need to grab the lock on the 'inputq'
list, irrespective of source node.
However, when transmitting node local messages those will eventually
end up on the receive path of a local socket, meaning that the argument
'xmitq' in tipc_node_xmit() will become the 'ínputq' argument in the
function tipc_sk_rcv(). This has been handled by always initializing
the spinlock of the 'xmitq' list at message creation, just in case it
may end up on the receive path later, and despite knowing that the lock
in most cases never will be used.
This approach is inaccurate and confusing, and has also concealed the
fact that the stated 'no lock grabbing' policy for the send path is
violated in some cases.
We now clean up this by never initializing the lock at message creation,
instead doing this at the moment we find that the message actually will
enter the receive path. At the same time we fix the four locations
where we incorrectly access the spinlock on the send/error path.
This patch also reverts commit d12cffe932 ("tipc: ensure head->lock
is initialised") which has now become redundant.
CC: Eric Dumazet <edumazet@google.com>
Reported-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit eliminates the use of the link 'stale_limit' & 'prev_from'
(besides the already removed - 'stale_cnt') variables in the detection
of repeated retransmit failures as there is no proper way to initialize
them to avoid a false detection, i.e. it is not really a retransmission
failure but due to a garbage values in the variables.
Instead, a jiffies variable will be added to individual skbs (like the
way we restrict the skb retransmissions) in order to mark the first skb
retransmit time. Later on, at the next retransmissions, the timestamp
will be checked to see if the skb in the link transmq is "too stale",
that is, the link tolerance time has passed, so that a link reset will
be ordered. Note, just checking on the first skb in the queue is fine
enough since it must be the oldest one.
A counter is also added to keep track the actual skb retransmissions'
number for later checking when the failure happens.
The downside of this approach is that the skb->cb[] buffer is about to
be exhausted, however it is always able to allocate another memory area
and keep a reference to it when needed.
Fixes: 77cf8edbc0 ("tipc: simplify stale link failure criteria")
Reported-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We set the field 'addr_trial_end' to 'jiffies', instead of the current
value 0, at the moment the node address is initialized. This guarantees
we don't inadvertently enter an address trial period when the node
address is explicitly set by the user.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since node internal messages are passed directly to the socket, it is not
possible to observe those messages via tcpdump or wireshark.
We now remedy this by making it possible to clone such messages and send
the clones to the loopback interface. The clones are dropped at reception
and have no functional role except making the traffic visible.
The feature is enabled if network taps are active for the loopback device.
pcap filtering restrictions require the messages to be presented to the
receiving side of the loopback device.
v3 - Function dev_nit_active used to check for network taps.
- Procedure netif_rx_ni used to send cloned messages to loopback device.
Signed-off-by: John Rutherford <john.rutherford@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 365ad353c2 ("tipc: reduce risk of user starvation during
link congestion") we allowed senders to add exactly one list of extra
buffers to the link backlog queues during link congestion (aka
"oversubscription"). However, the criteria for when to stop adding
wakeup messages to the input queue when the overload abates is
inaccurate, and may cause starvation problems during very high load.
Currently, we stop adding wakeup messages after 10 total failed attempts
where we find that there is no space left in the backlog queue for a
certain importance level. The counter for this is accumulated across all
levels, which may lead the algorithm to leave the loop prematurely,
although there may still be plenty of space available at some levels.
The result is sometimes that messages near the wakeup queue tail are not
added to the input queue as they should be.
We now introduce a more exact algorithm, where we keep adding wakeup
messages to a level as long as the backlog queue has free slots for
the corresponding level, and stop at the moment there are no more such
slots or when there are no more wakeup messages to dequeue.
Fixes: 365ad35 ("tipc: reduce risk of user starvation during link congestion")
Reported-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2753ca5d90 ("tipc: fix uninit-value in tipc_nl_compat_doit")
broke older tipc tools that use compat interface (e.g. tipc-config from
tipcutils package):
% tipc-config -p
operation not supported
The commit started to reject TIPC netlink compat messages that do not
have attributes. It is too restrictive because some of such messages are
valid (they don't need any arguments):
% grep 'tx none' include/uapi/linux/tipc_config.h
#define TIPC_CMD_NOOP 0x0000 /* tx none, rx none */
#define TIPC_CMD_GET_MEDIA_NAMES 0x0002 /* tx none, rx media_name(s) */
#define TIPC_CMD_GET_BEARER_NAMES 0x0003 /* tx none, rx bearer_name(s) */
#define TIPC_CMD_SHOW_PORTS 0x0006 /* tx none, rx ultra_string */
#define TIPC_CMD_GET_REMOTE_MNG 0x4003 /* tx none, rx unsigned */
#define TIPC_CMD_GET_MAX_PORTS 0x4004 /* tx none, rx unsigned */
#define TIPC_CMD_GET_NETID 0x400B /* tx none, rx unsigned */
#define TIPC_CMD_NOT_NET_ADMIN 0xC001 /* tx none, rx none */
This patch relaxes the original fix and rejects messages without
arguments only if such arguments are expected by a command (reg_type is
non zero).
Fixes: 2753ca5d90 ("tipc: fix uninit-value in tipc_nl_compat_doit")
Cc: stable@vger.kernel.org
Signed-off-by: Taras Kondratiuk <takondra@cisco.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In conjunction with changing the interfaces' MTU (e.g. especially in
the case of a bonding) where the TIPC links are brought up and down
in a short time, a couple of issues were detected with the current link
changeover mechanism:
1) When one link is up but immediately forced down again, the failover
procedure will be carried out in order to failover all the messages in
the link's transmq queue onto the other working link. The link and node
state is also set to FAILINGOVER as part of the process. The message
will be transmited in form of a FAILOVER_MSG, so its size is plus of 40
bytes (= the message header size). There is no problem if the original
message size is not larger than the link's MTU - 40, and indeed this is
the max size of a normal payload messages. However, in the situation
above, because the link has just been up, the messages in the link's
transmq are almost SYNCH_MSGs which had been generated by the link
synching procedure, then their size might reach the max value already!
When the FAILOVER_MSG is built on the top of such a SYNCH_MSG, its size
will exceed the link's MTU. As a result, the messages are dropped
silently and the failover procedure will never end up, the link will
not be able to exit the FAILINGOVER state, so cannot be re-established.
2) The same scenario above can happen more easily in case the MTU of
the links is set differently or when changing. In that case, as long as
a large message in the failure link's transmq queue was built and
fragmented with its link's MTU > the other link's one, the issue will
happen (there is no need of a link synching in advance).
3) The link synching procedure also faces with the same issue but since
the link synching is only started upon receipt of a SYNCH_MSG, dropping
the message will not result in a state deadlock, but it is not expected
as design.
The 1) & 3) issues are resolved by the last commit that only a dummy
SYNCH_MSG (i.e. without data) is generated at the link synching, so the
size of a FAILOVER_MSG if any then will never exceed the link's MTU.
For the 2) issue, the only solution is trying to fragment the messages
in the failure link's transmq queue according to the working link's MTU
so they can be failovered then. A new function is made to accomplish
this, it will still be a TUNNEL PROTOCOL/FAILOVER MSG but if the
original message size is too large, it will be fragmented & reassembled
at the receiving side.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit along with the next one are to resolve the issues with the
link changeover mechanism. See that commit for details.
Basically, for the link synching, from now on, we will send only one
single ("dummy") SYNCH message to peer. The SYNCH message does not
contain any data, just a header conveying the synch point to the peer.
A new node capability flag ("TIPC_TUNNEL_ENHANCED") is introduced for
backward compatible!
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Suggested-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
s/tipc_toprsv_listener_data_ready/tipc_topsrv_listener_data_ready/
(r and s switched in topsrv)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix AF_XDP cq entry leak, from Ilya Maximets.
2) Fix handling of PHY power-down on RTL8411B, from Heiner Kallweit.
3) Add some new PCI IDs to iwlwifi, from Ihab Zhaika.
4) Fix handling of neigh timers wrt. entries added by userspace, from
Lorenzo Bianconi.
5) Various cases of missing of_node_put(), from Nishka Dasgupta.
6) The new NET_ACT_CT needs to depend upon NF_NAT, from Yue Haibing.
7) Various RDS layer fixes, from Gerd Rausch.
8) Fix some more fallout from TCQ_F_CAN_BYPASS generalization, from
Cong Wang.
9) Fix FIB source validation checks over loopback, also from Cong Wang.
10) Use promisc for unsupported number of filters, from Justin Chen.
11) Missing sibling route unlink on failure in ipv6, from Ido Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (90 commits)
tcp: fix tcp_set_congestion_control() use from bpf hook
ag71xx: fix return value check in ag71xx_probe()
ag71xx: fix error return code in ag71xx_probe()
usb: qmi_wwan: add D-Link DWM-222 A2 device ID
bnxt_en: Fix VNIC accounting when enabling aRFS on 57500 chips.
net: dsa: sja1105: Fix missing unlock on error in sk_buff()
gve: replace kfree with kvfree
selftests/bpf: fix test_xdp_noinline on s390
selftests/bpf: fix "valid read map access into a read-only array 1" on s390
net/mlx5: Replace kfree with kvfree
MAINTAINERS: update netsec driver
ipv6: Unlink sibling route in case of failure
liquidio: Replace vmalloc + memset with vzalloc
udp: Fix typo in net/ipv4/udp.c
net: bcmgenet: use promisc for unsupported filters
ipv6: rt6_check should return NULL if 'from' is NULL
tipc: initialize 'validated' field of received packets
selftests: add a test case for rp_filter
fib: relax source validation check for loopback packets
mlxsw: spectrum: Do not process learned records with a dummy FID
...
In the sysctl code the proc_dointvec_minmax() function is often used to
validate the user supplied value between an allowed range. This
function uses the extra1 and extra2 members from struct ctl_table as
minimum and maximum allowed value.
On sysctl handler declaration, in every source file there are some
readonly variables containing just an integer which address is assigned
to the extra1 and extra2 members, so the sysctl range is enforced.
The special values 0, 1 and INT_MAX are very often used as range
boundary, leading duplication of variables like zero=0, one=1,
int_max=INT_MAX in different source files:
$ git grep -E '\.extra[12].*&(zero|one|int_max)' |wc -l
248
Add a const int array containing the most commonly used values, some
macros to refer more easily to the correct array member, and use them
instead of creating a local one for every object file.
This is the bloat-o-meter output comparing the old and new binary
compiled with the default Fedora config:
# scripts/bloat-o-meter -d vmlinux.o.old vmlinux.o
add/remove: 2/2 grow/shrink: 0/2 up/down: 24/-188 (-164)
Data old new delta
sysctl_vals - 12 +12
__kstrtab_sysctl_vals - 12 +12
max 14 10 -4
int_max 16 - -16
one 68 - -68
zero 128 28 -100
Total: Before=20583249, After=20583085, chg -0.00%
[mcroce@redhat.com: tipc: remove two unused variables]
Link: http://lkml.kernel.org/r/20190530091952.4108-1-mcroce@redhat.com
[akpm@linux-foundation.org: fix net/ipv6/sysctl_net_ipv6.c]
[arnd@arndb.de: proc/sysctl: make firmware loader table conditional]
Link: http://lkml.kernel.org/r/20190617130014.1713870-1-arnd@arndb.de
[akpm@linux-foundation.org: fix fs/eventpoll.c]
Link: http://lkml.kernel.org/r/20190430180111.10688-1-mcroce@redhat.com
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tipc_msg_validate() function leaves a boolean flag 'validated' in
the validated buffer's control block, to avoid performing this action
more than once. However, at reception of new packets, the position of
this field may already have been set by lower layer protocols, so
that the packet is erroneously perceived as already validated by TIPC.
We fix this by initializing the said field to 'false' before performing
the initial validation.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_named_node_up() creates a skb list. It passes the list to
tipc_node_xmit() which has some code paths that can call
skb_queue_purge() which relies on the list->lock being initialised.
The spin_lock is only needed if the messages end up on the receive path
but when the list is created in tipc_named_node_up() we don't
necessarily know if it is going to end up there.
Once all the skb list users are updated in tipc it will then be possible
to update them to use the unlocked variants of the skb list functions
and initialise the lock when we know the message will follow the receive
path.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with other
trees, unfortunately. He has a lot more of these waiting on the wings
that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos, and one
on Spectre vulnerabilities.
- Various improvements to the build system, including automatic markup of
function() references because some people, for reasons I will never
understand, were of the opinion that :c:func:``function()`` is
unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl0krAEPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yg98H/AuLqO9LpOgUjF4LhyjxGPdzJkY9RExSJ7km
gznyreLCZgFaJR+AY6YDsd4Jw6OJlPbu1YM/Qo3C3WrZVFVhgL/s2ebvBgCo50A8
raAFd8jTf4/mGCHnAqRotAPQ3mETJUk315B66lBJ6Oc+YdpRhwXWq8ZW2bJxInFF
3HDvoFgMf0KhLuMHUkkL0u3fxH1iA+KvDu8diPbJYFjOdOWENz/CV8wqdVkXRSEW
DJxIq89h/7d+hIG3d1I7Nw+gibGsAdjSjKv4eRKauZs4Aoxd1Gpl62z0JNk6aT3m
dtq4joLdwScydonXROD/Twn2jsu4xYTrPwVzChomElMowW/ZBBY=
=D0eO
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
For these places are protected by rcu_read_lock, we change from
rcu_dereference_rtnl to rcu_dereference, as there is no need to
check if rtnl lock is held.
For these places are protected by rtnl_lock, we change from
rcu_dereference_rtnl to rtnl_dereference/rcu_dereference_protected,
as no extra memory barriers are needed under rtnl_lock() which also
protects tn->bearer_list[] and dev->tipc_ptr/b->media_ptr updating.
rcu_dereference_rtnl will be only used in the places where it could
be under rcu_read_lock or rtnl_lock.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both tipc_udp_enable and tipc_udp_disable are called under rtnl_lock,
ub->ubsock could never be NULL in tipc_udp_disable and cleanup_bearer,
so remove the check.
Also remove the one in tipc_udp_enable by adding "free" label.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro TIPC_BC_RETR_LIM is always used in combination with 'jiffies',
so we can just as well perform the addition in the macro itself. This
way, we get a few shorter code lines and one less line break.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As other udp/ip tunnels do, tipc udp media should also have a
lockless dst_cache supported on its tx path.
Here we add dst_cache into udp_replicast to support dst cache
for both rmcast and rcast, and rmcast uses ub->rcast and each
rcast uses its own node in ub->rcast.list.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new route handling in ip_mc_finish_output() from 'net' overlapped
with the new support for returning congestion notifications from BPF
programs.
In order to handle this I had to take the dev_loopback_xmit() calls
out of the switch statement.
The aquantia driver conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
We rename the inline function msg_get_wrapped() to the more
comprehensible msg_inner_hdr().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We increase the allocated headroom for the buffer copies to be
retransmitted. This eliminates the need for the lower stack levels
(UDP/IP/L2) to expand the headroom in order to add their own headers.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit a4dc70d46c ("tipc: extend link reset criteria for stale
packet retransmission") we made link retransmission failure events
dependent on the link tolerance, and not only of the number of failed
retransmission attempts, as we did earlier. This works well. However,
keeping the original, additional criteria of 99 failed retransmissions
is now redundant, and may in some cases lead to failure detection
times in the order of minutes instead of the expected 1.5 sec link
tolerance value.
We now remove this criteria altogether.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix an uninit-value issue, reported by syzbot:
BUG: KMSAN: uninit-value in memchr+0xce/0x110 lib/string.c:981
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x191/0x1f0 lib/dump_stack.c:113
kmsan_report+0x130/0x2a0 mm/kmsan/kmsan.c:622
__msan_warning+0x75/0xe0 mm/kmsan/kmsan_instr.c:310
memchr+0xce/0x110 lib/string.c:981
string_is_valid net/tipc/netlink_compat.c:176 [inline]
tipc_nl_compat_bearer_disable+0x2a1/0x480 net/tipc/netlink_compat.c:449
__tipc_nl_compat_doit net/tipc/netlink_compat.c:327 [inline]
tipc_nl_compat_doit+0x3ac/0xb00 net/tipc/netlink_compat.c:360
tipc_nl_compat_handle net/tipc/netlink_compat.c:1178 [inline]
tipc_nl_compat_recv+0x1b1b/0x27b0 net/tipc/netlink_compat.c:1281
TLV_GET_DATA_LEN() may return a negtive int value, which will be
used as size_t (becoming a big unsigned long) passed into memchr,
cause this issue.
Similar to what it does in tipc_nl_compat_bearer_enable(), this
fix is to return -EINVAL when TLV_GET_DATA_LEN() is negtive in
tipc_nl_compat_bearer_disable(), as well as in
tipc_nl_compat_link_stat_dump() and tipc_nl_compat_link_reset_stats().
v1->v2:
- add the missing Fixes tags per Eric's request.
Fixes: 0762216c0a ("tipc: fix uninit-value in tipc_nl_compat_bearer_enable")
Fixes: 8b66fee7f8 ("tipc: fix uninit-value in tipc_nl_compat_link_reset_stats")
Reported-by: syzbot+30eaa8bf392f7fafffaf@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_nl_compat_bearer_set() is only called by tipc_nl_compat_link_set()
which already does the check for msg->req check, so remove it from
tipc_nl_compat_bearer_set(), and do the same in tipc_nl_compat_media_set().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix misalignment of policy statement in netlink.c due to automatic
spatch code transformation.
Fixes: 3b0f31f2b8 ("genetlink: make policy common to family")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: John Rutherford <john.rutherford@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix a dst defcnt leak, which can be reproduced by doing:
# ip net a c; ip net a s; modprobe tipc
# ip net e s ip l a n eth1 type veth peer n eth1 netns c
# ip net e c ip l s lo up; ip net e c ip l s eth1 up
# ip net e s ip l s lo up; ip net e s ip l s eth1 up
# ip net e c ip a a 1.1.1.2/8 dev eth1
# ip net e s ip a a 1.1.1.1/8 dev eth1
# ip net e c tipc b e m udp n u1 localip 1.1.1.2
# ip net e s tipc b e m udp n u1 localip 1.1.1.1
# ip net d c; ip net d s; rmmod tipc
and it will get stuck and keep logging the error:
unregister_netdevice: waiting for lo to become free. Usage count = 1
The cause is that a dst is held by the udp sock's sk_rx_dst set on udp rx
path with udp_early_demux == 1, and this dst (eventually holding lo dev)
can't be released as bearer's removal in tipc pernet .exit happens after
lo dev's removal, default_device pernet .exit.
"There are two distinct types of pernet_operations recognized: subsys and
device. At creation all subsys init functions are called before device
init functions, and at destruction all device exit functions are called
before subsys exit function."
So by calling register_pernet_device instead to register tipc_net_ops, the
pernet .exit() will be invoked earlier than loopback dev's removal when a
netns is being destroyed, as fou/gue does.
Note that vxlan and geneve udp tunnels don't have this issue, as the udp
sock is released in their device ndo_stop().
This fix is also necessary for tipc dst_cache, which will hold dsts on tx
path and I will introduce in my next patch.
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udp_tunnel(6)_xmit_skb() called by tipc_udp_xmit() expects a tunnel device
to count packets on dev->tstats, a perpcu variable. However, TIPC is using
udp tunnel with no tunnel device, and pass the lower dev, like veth device
that only initializes dev->lstats(a perpcu variable) when creating it.
Later iptunnel_xmit_stats() called by ip(6)tunnel_xmit() thinks the dev as
a tunnel device, and uses dev->tstats instead of dev->lstats. tstats' each
pointer points to a bigger struct than lstats, so when tstats->tx_bytes is
increased, other percpu variable's members could be overwritten.
syzbot has reported quite a few crashes due to fib_nh_common percpu member
'nhc_pcpu_rth_output' overwritten, call traces are like:
BUG: KASAN: slab-out-of-bounds in rt_cache_valid+0x158/0x190
net/ipv4/route.c:1556
rt_cache_valid+0x158/0x190 net/ipv4/route.c:1556
__mkroute_output net/ipv4/route.c:2332 [inline]
ip_route_output_key_hash_rcu+0x819/0x2d50 net/ipv4/route.c:2564
ip_route_output_key_hash+0x1ef/0x360 net/ipv4/route.c:2393
__ip_route_output_key include/net/route.h:125 [inline]
ip_route_output_flow+0x28/0xc0 net/ipv4/route.c:2651
ip_route_output_key include/net/route.h:135 [inline]
...
or:
kasan: GPF could be caused by NULL-ptr deref or user memory access
RIP: 0010:dst_dev_put+0x24/0x290 net/core/dst.c:168
<IRQ>
rt_fibinfo_free_cpus net/ipv4/fib_semantics.c:200 [inline]
free_fib_info_rcu+0x2e1/0x490 net/ipv4/fib_semantics.c:217
__rcu_reclaim kernel/rcu/rcu.h:240 [inline]
rcu_do_batch kernel/rcu/tree.c:2437 [inline]
invoke_rcu_callbacks kernel/rcu/tree.c:2716 [inline]
rcu_process_callbacks+0x100a/0x1ac0 kernel/rcu/tree.c:2697
...
The issue exists since tunnel stats update is moved to iptunnel_xmit by
Commit 039f50629b ("ip_tunnel: Move stats update to iptunnel_xmit()"),
and here to fix it by passing a NULL tunnel dev to udp_tunnel(6)_xmit_skb
so that the packets counting won't happen on dev->tstats.
Reported-by: syzbot+9d4c12bfd45a58738d0a@syzkaller.appspotmail.com
Reported-by: syzbot+a9e23ea2aa21044c2798@syzkaller.appspotmail.com
Reported-by: syzbot+c4c4b2bb358bb936ad7e@syzkaller.appspotmail.com
Reported-by: syzbot+0290d2290a607e035ba1@syzkaller.appspotmail.com
Reported-by: syzbot+a43d8d4e7e8a7a9e149e@syzkaller.appspotmail.com
Reported-by: syzbot+a47c5f4c6c00fc1ed16e@syzkaller.appspotmail.com
Fixes: 039f50629b ("ip_tunnel: Move stats update to iptunnel_xmit()")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It appears that a FAILOVER_MSG can come from peer even when the failure
link is resetting (i.e. just after the 'node_write_unlock()'...). This
means the failover procedure on the node has not been started yet.
The situation is as follows:
node1 node2
linkb linka linka linkb
| | | |
| | x failure |
| | RESETTING |
| | | |
| x failure RESET |
| RESETTING FAILINGOVER |
| | (FAILOVER_MSG) | |
|<-------------------------------------------------|
| *FAILINGOVER | | |
| | (dummy FAILOVER_MSG) | |
|------------------------------------------------->|
| RESET | | FAILOVER_END
| FAILINGOVER RESET |
. . . .
. . . .
. . . .
Once this happens, the link failover procedure will be triggered
wrongly on the receiving node since the node isn't in FAILINGOVER state
but then another link failover will be carried out.
The consequences are:
1) A peer might get stuck in FAILINGOVER state because the 'sync_point'
was set, reset and set incorrectly, the criteria to end the failover
would not be met, it could keep waiting for a message that has already
received.
2) The early FAILOVER_MSG(s) could be queued in the link failover
deferdq but would be purged or not pulled out because the 'drop_point'
was not set correctly.
3) The early FAILOVER_MSG(s) could be dropped too.
4) The dummy FAILOVER_MSG could make the peer leaving FAILINGOVER state
shortly, but later on it would be restarted.
The same situation can also happen when the link is in PEER_RESET state
and a FAILOVER_MSG arrives.
The commit resolves the issues by forcing the link down immediately, so
the failover procedure will be started normally (which is the same as
when receiving a FAILOVER_MSG and the link is in up state).
Also, the function "tipc_node_link_failover()" is toughen to avoid such
a situation from happening.
Acked-by: Jon Maloy <jon.maloy@ericsson.se>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In patch series, commit 9195948fbf ("tipc: improve TIPC throughput by
Gap ACK blocks"), as for simplicity, the repeated retransmit failures'
detection in the function - "tipc_link_retrans()" was kept there for
broadcast retransmissions only.
This commit now reapplies this feature for link unicast retransmissions
that has been done via the function - "tipc_link_advance_transmq()".
Also, the "tipc_link_retrans()" is renamed to "tipc_link_bc_retrans()"
as it is used only for broadcast.
Acked-by: Jon Maloy <jon.maloy@ericsson.se>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported a memleak caused by grp members' deferredq list not
purged when the grp is be deleted.
The issue occurs when more(msg_grp_bc_seqno(hdr), m->bc_rcv_nxt) in
tipc_group_filter_msg() and the skb will stay in deferredq.
So fix it by calling __skb_queue_purge for each member's deferredq
in tipc_group_delete() when a tipc sk leaves the grp.
Fixes: b87a5ea31c ("tipc: guarantee group unicast doesn't bypass group broadcast")
Reported-by: syzbot+78fbe679c8ca8d264a8d@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kbuild documentation clearly shows that the documents
there are written at different times: some use markdown,
some use their own peculiar logic to split sections.
Convert everything to ReST without affecting too much
the author's style and avoiding adding uneeded markups.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Pull networking fixes from David Miller:
1) Clear up some recent tipc regressions because of registration
ordering. Fix from Junwei Hu.
2) tipc's TLV_SET() can read past the end of the supplied buffer during
the copy. From Chris Packham.
3) ptp example program doesn't match the kernel, from Richard Cochran.
4) Outgoing message type fix in qrtr, from Bjorn Andersson.
5) Flow control regression in stmmac, from Tan Tee Min.
6) Fix inband autonegotiation in phylink, from Russell King.
7) Fix sk_bound_dev_if handling in rawv6_bind(), from Mike Manning.
8) Fix usbnet crash after disconnect, from Kloetzke Jan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
usbnet: fix kernel crash after disconnect
selftests: fib_rule_tests: use pre-defined DEV_ADDR
net-next: net: Fix typos in ip-sysctl.txt
ipv6: Consider sk_bound_dev_if when binding a raw socket to an address
net: phylink: ensure inband AN works correctly
usbnet: ipheth: fix racing condition
net: stmmac: dma channel control register need to be init first
net: stmmac: fix ethtool flow control not able to get/set
net: qrtr: Fix message type of outgoing packets
networking: : fix typos in code comments
ptp: Fix example program to match kernel.
fddi: fix typos in code comments
selftests: fib_rule_tests: enable forwarding before ipv4 from/iif test
selftests: fib_rule_tests: fix local IPv4 address typo
tipc: Avoid copying bytes beyond the supplied data
2/2] net: xilinx_emaclite: use readx_poll_timeout() in mdio wait function
1/2] net: axienet: use readx_poll_timeout() in mdio wait function
vlan: Mark expected switch fall-through
macvlan: Mark expected switch fall-through
net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query
...
