Cannonlake Slice and Subslice information has changed.
This patch initially provided by Ben adds the proper sseu
initialization.
v2: This v2 done by Rodrigo includes:
- Fix on Total slices count by avoiding [1][2] and [2][2].
- Inclusion of EU Per Subslice.
- Commit message.
v3: This v3 done by Rodrigo includes:
- Handle all possible bits and extra fuse register.
- Use INTEL_GEN macro.
- Fully assume uniform distribution so remove union
with eu_per_subslice and add proper the comment.
v4: This v4 done by Rodrigo includes:
- Consider all bits available: 6 bits for slices [27:22]
and 4 for subslices [21:18].
v5: This v5 done by Rodrigo includes:
- sseu->subslice_mask = (1 << 4) - 1 - missed on previous
versions and noticed by Oscar.
Cc: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170920183525.20530-1-rodrigo.vivi@intel.com
For certain platforms on certain encoders, timings are driven
from port instead of pipe. Thus, we can't rely on pipe scanline
registers to get the timing information. Some cases scanline
register read will not be functional.
This is causing vblank evasion logic to fail since it relies on
scanline, causing atomic update failure warnings.
This patch uses pipe framestamp and current timestamp registers
to calculate scanline. This is an indirect way to get the scanline.
It helps resolve atomic update failure for gen9 dsi platforms.
v2: Addressed Ville and Daniel's review comments. Updated the
register MACROs, handled race condition for register reads,
extracted timings from the hwmode. Removed the dependency on
crtc->config to get the encoder type.
v3: Made get scanline function generic
v4: Addressed Ville's review comments. Added a flag to decide timestamp
based scanline reporting. Changed 64bit variables to u32
v5: Adressed Ville's review comments. Put the scanline compute function
at the place of caller. Removed hwmode flags from uapi and used a local
i915 data structure instead.
v6: Used vblank hwmode to get the timings.
v7: Fixed sparse warnings, indentation and minor review comments.
v8: Limited this only for Gen9 DSI.
Credits-to: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Chandra Konduru <chandra.konduru@intel.com>
Signed-off-by: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1506347761-4201-1-git-send-email-vidya.srinivas@intel.com
"CNL PCH chance of hang when software accesses south display
registers after hotplug is enabled.
Workaround: Program 0xC2000 bits 11:8 = 0xF before enabling
south display hotplug detection."
"Workaround only needs to be applied to pre-production steppings
used in graphics capable SKUs, but it is easier to apply to
everything, and does not hurt."
v2: Moving from clock gating to right before enabling
SHOTPLUG_CTL as it should be.
v3: Align with SOUTH_CHICKEN1 (DK) and consequently use proper
spaces on bits definition since other bits around already use
new style. And now that checkpatch is not noise anymore I also
fixed the reg read mask to avoid going over 80 chars.
Suggested-by: Ben Widawsky <ben@bwidawsk.net>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170919215703.25947-1-rodrigo.vivi@intel.com
No functional changes. Only change the macro from
"DPLL_CFGCR0_DC0_FRAC_SHIFT to DPLL_CFGCR0_DCO_FRACTION_SHIFT
to be consistent with DPLL_CFGCR0_DCO_FRACTION_MASK
and DPLL_CFGCR0_DCO_FRACTION
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1505413899-30876-1-git-send-email-manasi.d.navare@intel.com
Use the LLC/eLLC hotspot avoidance mode for CCS on LLC machines. This is
reported to give better performance.
Testing has indicated that we don't need to enforce any massive 2 or 4
MiB alignment for all compressed resources even though there are still
plenty of stale comments in the spec suggesting that we do.
We do need to make sure every hardware unit that deals with the
compressed data uses the same hash mode.
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Daniel Stone <daniels@collabora.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170824191100.10949-4-ville.syrjala@linux.intel.com
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Macro params shall be wrapped into () to avoid unexpected results.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908161130.22424-1-michal.wajdeczko@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This patch adds IPC support. This patch also enables IPC in all supported
platforms based on has_ipc flag.
IPC (Isochronous Priority Control) is the hardware feature, which
dynamically controls the memory read priority of Display.
When IPC is enabled, plane read requests are sent at high priority until
filling above the transition watermark, then the requests are sent at
lower priority until dropping below the level 0 watermark.
The lower priority requests allow other memory clients to have better
memory access. When IPC is disabled, all plane read requests are sent at
high priority.
Changes since V1:
- Remove commandline parameter to disable ipc
- Address Paulo's comments
Changes since V2:
- Address review comments
- Set ipc_enabled flag
Changes since V3:
- move ipc_enabled flag assignment inside intel_ipc_enable function
Changes since V4:
- Re-enable IPC after suspend/resume
Changes since V5:
- Enable IPC for all gen >=9 except SKL
Changes since V6:
- fix commit msg
- after resume program IPC based on SW state.
Changes since V7:
- Modify IPC support check based on HAS_IPC macro (suggested by Chris)
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170817134529.2839-8-mahesh1.kumar@intel.com
Wa for B-stepping only.
A for a hang issue that requires throttling EU performace
to 12.5% to avoid back pressure to thread dispatch
v2: Rebased. No change from v1.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170906220325.24524-1-rodrigo.vivi@intel.com
Skip compressing 1 segment at the end of the frame,
avoid a pixel count mismatch nuke event when last active
pixel and dummy pixel has same color for Odd Plane
Width / Height.
For both platforms Gemini Lake and Cannon Lake.
v2: Use function-like macro and also use mask to clean
to make sure bit 11 is 0. (Suggested by Paulo).
v3: Add Display WA notation and also apply for GLK.
Both Forgotten on v2.
Using "GLK_" prefix since GLK came before CNL.
v4: Forgot to "|=" when moving directly macro to masked
val. (Noticed by Paulo.)
v5: Rebased on top of 0a46ddd57c ("drm/i915/cnp: Wa 1181:
Fix Backlight issue")
Cc: Imre Deak <imre.deak@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170905193013.31710-1-rodrigo.vivi@intel.com
This workaround fixes a CNL PCH bug when changing
backlight from a lower frequency to a higher frequency.
During random reboot cycles, display backlight seems to
be off/ dim for 2-3 mins.
The only functional change on this patch is to
set bit 13 of 0xC2020 for CNL PCH.
The rest of patch is organizing identation around
those bits definitions and re-organizing CFL workarounds.
v2: Only add the bit that matters without touching others
around (Jani).
Rebase on top of clock gating functions rename.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170831045223.3960-1-rodrigo.vivi@intel.com
On CNL B0 stepping GAM is not able to detect some deadlock
condition and then rise the rise the gam_coh_flush.
WA database and spec both mentions to set 4AB8[24]=1 as
workaround. Although register offset 0x4AB8 is not
documented for any platform.
References: HSD#1945815, BSID#1112
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170829230751.21047-1-rodrigo.vivi@intel.com
WA to enable HW L1 Banking fix that allows aniso to operate
at full sample rate.
References: HSD#1937670
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Anuj Phogat <anuj.phogat@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170829230723.20898-1-rodrigo.vivi@intel.com
When FBC is enabled for linear, legacy Y-tiled and Yf-tiled
surfaces on gen9, the cfb stride must be programmed by SW as
cfb_stride = ceiling[(at least plane width in pixels)/
(32 * compression limit factor)] * 8
v2: Minor fix for a build error
v3: Fixed subject, register name and platform check (Ville)
v4: Added WA details in comment (Paulo)
v5:
- Read modified reg write to preserve other bit values (Paulo)
- Store modified stride value in reg_params (Paulo)
- Keep GLK out of the WA (Paulo)
v6:
- added additional field in reg_params for gen9_wa_cfb_stride (Paulo)
- Used appropriate bit mask while writing the register (Paulo)
v7 (from Paulo):
- Fix coding style and spacing issues.
- Mask the old values before writing.
- Bikeshed comments and unnecessary checks.
Signed-off-by: Praveen Paneri <praveen.paneri@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1502389833-32621-1-git-send-email-praveen.paneri@intel.com
To avoid a potential hang condition with TLB invalidation
we need to enable masked bit 5 of MMIO 0xE5F0 at boot.
Same workaround was in place for previous platforms,
but the register offset has changed for CNL.
But also BSpec doesn't mention the bit 15 as set on gen9
platforms and mark bit as reserved on CNL.
v2: Improve commit message accepting Oscar's suggestion.
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170823203504.10012-1-rodrigo.vivi@intel.com
CS sometimes hangs on 3D Push Constant dispatches with the new
deref enhancement logic in CNL.
v2: Improve the commit message (Rodrigo)
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1503518191-19116-1-git-send-email-oscar.mateo@intel.com
This bit enables hardware that will change the approximation used for distances
calculations for AA wide lines so that they are rendered more accurately.
The default value for this bit leaves the legacy behavior. There is no good
reason to not enable the new approximation except if comparing to previous GEN
rendered images.
v2: Rebase
v3: Fix author.
Rebased by Rodrigo who also added a comment as suggested by Oscar.
Since it is surrounded by Workarounds let's just add a comment to
make clear it is not an Wa.
Cc: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170815231651.975-4-rodrigo.vivi@intel.com
Let's inherit workarounds from previous platforms that
according to wa_database and BSpec are still valid for
Cannonlake.
v2: Add missed workarounds.
v3: Rebase
v4: Remove bad chunk that was added to rc6 disable. (Ander)
Also remove A0 W/a that are not needed anymore.
v5: Rebase on top of CFL.
v6: Remove empty gen9_init_perctx_bb and gen9_init_indirectctx_bb
since they don't carry any gen10 related W/a. (by Oscar).
Also Remove A0 exclusive workaround.
v7: Remove more A0 exclusive workarounds. As pointed out by Oscar
many workarounds were changed to be A0 only so let's remove
them.
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170815231651.975-1-rodrigo.vivi@intel.com
Different from previous platforms, on CNL+ there's separated
registers for separated indexes.
v2: Remove comments regarding uncertainty around the table.
v3: Remove extra line (by Ben)
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170815232539.3562-1-rodrigo.vivi@intel.com
Future platforms increase the number of power wells which require
additional control registers. A convenient way to select the correct
register is to use the high bits of the power well ID as index. This
patch only prepares for this, while upcoming platform enabling patches
will add the actual new power well IDs and corresponding power well
control registers.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Rakshmi Bhatia <rakshmi.bhatia@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Rakshmi Bhatia <rakshmi.bhatia@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170814151530.24154-2-imre.deak@intel.com
This is not to try to force a new style; this is my interpretation of
what the most common existing style is.
With hopes I don't need to answer so many questions about style going
forward.
Start a new style section in the i915 document to bolt the register
style guide into.
v2: vertical alignment, incorporate to kernel-doc, and more
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9de4a5b1bea4e76461c70a1dd66751581de0124f.1502368010.git.jani.nikula@intel.com
SKL+ display engine can scan out certain kinds of compressed surfaces
produced by the render engine. This involved telling the display engine
the location of the color control surfae (CCS) which describes
which parts of the main surface are compressed and which are not. The
location of CCS is provided by userspace as just another plane with its
own offset.
Add the required stuff to validate the user provided AUX plane metadata
and convert the user provided linear offset into something the hardware
can consume.
Due to hardware limitations we require that the main surface and
the AUX surface (CCS) be part of the same bo. The hardware also
makes life hard by not allowing you to provide separate x/y offsets
for the main and AUX surfaces (excpet with NV12), so finding suitable
offsets for both requires a bit of work. Assuming we still want keep
playing tricks with the offsets. I've just gone with a dumb "search
backward for suitable offsets" approach, which is far from optimal,
but it works.
Also not all planes will be capable of scanning out compressed surfaces,
and eg. 90/270 degree rotation is not supported in combination with
decompression either.
This patch may contain work from at least the following people:
* Vandana Kannan <vandana.kannan@intel.com>
* Daniel Vetter <daniel@ffwll.ch>
* Ben Widawsky <ben@bwidawsk.net>
v2: Deal with display workarounds 0390, 0531, 1125 (Paulo)
v3: Pretend CCS tiles are regular 128 byte wide Y tiles (Jason)
Put the AUX register defines to the correct place
Fix up the slightly bogus rotation check
v4: Use I915_WRITE_FW() due to plane update locking changes
s/return -EINVAL/goto err/ in intel_framebuffer_init()
Eliminate a bunch hardcoded numbers in CCS code
v5: (By Ben)
conflict resolution +
- res_blocks += fixed_16_16_to_u32_round_up(y_tile_minimum);
+ res_blocks += fixed16_to_u32_round_up(y_tile_minimum);
v6: (daniels) Fix botched commit message.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Ville Syrjä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Stone <daniels@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170801165817.7063-1-ben@bwidawsk.net
Bit 29 of SRD_CTL needs to have its value preserved according to the
B-Spec, so right before we write out the register we go ahead and read
the register and preserve the value of that bit before we write out
the configured register value.
v2: Spaces => tabs, minor name change, and commit message wording (Rodrigo)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jim Bride <jim.bride@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1502229094-13392-1-git-send-email-jim.bride@linux.intel.com
The motivation behind this new interface is expose at runtime the
creation of new OA configs which can be used as part of the i915 perf
open interface. This will enable the kernel to learn new configs which
may be experimental, or otherwise not part of the core set currently
available through the i915 perf interface.
v2: Drop DRM_ERROR for userspace errors (Matthew)
Add padding to userspace structure (Matthew)
s/guid/uuid/ (Matthew)
v3: Use u32 instead of int to iterate through registers (Matthew)
v4: Lock access to dynamic config list (Lionel)
v5: by Matthew:
Fix uninitialized error values
Fix incorrect unwiding when opening perf stream
Use kmalloc_array() to store register
Use uuid_is_valid() to valid config uuids
Declare ioctls as write only
Check padding members are set to 0
by Lionel:
Return ENOENT rather than EINVAL when trying to remove non
existing config
v6: by Chris:
Use ref counts for OA configs
Store UUID in drm_i915_perf_oa_config rather then using pointer
Shuffle fields of drm_i915_perf_oa_config to avoid padding
v7: by Chris
Rename uapi pointers fields to end with '_ptr'
v8: by Andrzej, Marek, Sebastian
Update register whitelisting
by Lionel
Add more register names for documentation
Allow configuration programming in non-paranoid mode
Add support for value filter for a couple of registers already
programmed in other part of the kernel
v9: Documentation fix (Lionel)
Allow writing WAIT_FOR_RC6_EXIT only on Gen8+ (Andrzej)
v10: Perform read access_ok() on register pointers (Lionel)
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Andrzej Datczuk <andrzej.datczuk@intel.com>
Reviewed-by: Andrzej Datczuk <andrzej.datczuk@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170803165812.2373-2-lionel.g.landwerlin@intel.com
* Don't define it twice.
* Define MSBs first, like the rest of i915_reg.h.
* Add CNL_ prefix to the bit that arrived in CNL.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170714175228.27019-1-paulo.r.zanoni@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To get HDMI YCBCR420 output, the PIPEMISC register should be
programmed to:
- Generate YCBCR output (bit 11)
- In case of YCBCR420 outputs, it should be programmed in full
blend mode to use the scaler in 5x3 ratio (bits 26 and 27)
This patch:
- Adds definition of these bits.
- Programs PIPEMISC for YCBCR420 outputs.
- Adds readouts to compare HW and SW states.
V2: rebase
V3: rebase
V4: rebase
V5: added r-b from Ander
V6: Handle only YCBCR420 outputs (ville)
V7: rebase
V8: Addressed review comments from Ville
- Add readouts for state->ycbcr420 and 420 pixel_clock.
- Handle warning due to mismatch in clock for ycbcr420 clock.
- Rename PIPEMISC macros to match the Bspec.
- Add a debug print stating if YCBCR 4:2:0 output enabled.
Added r-b from Ville
V9: Addressed review comments from Imre:
- Add 420 mode clock adjustment in intel_hdmi_mode_valid to
prevent 420_only modes getting rejected for high clock.
- Add port clock adjustment for ycbcr420 modes in ddi_get_clock
- Rename macros as per Ville's suggestion.
- Remove unnecessary wl changes.
V10: Added r-b from Imre
V11: Fixed faulty dotclock handling, and addressed missing comment
from previous set of review comments (Imre)
V12: Fixed dotclock for 12bpc too, removed 420 check for GEN < 10
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1500904172-31717-1-git-send-email-shashank.sharma@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pattern of a power well backing a set of fuses whose initialization
we need to wait for during power well enabling is common to all GEN9+
platforms. Adding support for this to the HSW power well enable helper
allows us to use the HSW/BDW power well code for GEN9+ as well in a
follow-up patch.
v2:
- Use an enum for power gates instead of raw numbers. (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-6-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Although on HSW/BDW there is only a single display global power well,
it's programmed the same way as other GEN9+ power wells. This also
means we can get at the HSW/BDW request and status flags the same way
it's done on GEN9+ by assigning the corresponding HSW/BDW power well ID.
This ID was assigned in a recent patch, so we can now switch to using
the same macros everywhere on HSW+.
Updating the HSW power well control register with RMW is not strictly
necessary, but this will allow us to use the same code for GEN9+.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-13-git-send-email-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add an ID for the HSW/BDW global display power well for consistency. The
ID is selected so that it can be used to get at the HW request and
status flags with the corresponding GEN9+ macros. Unifying the HSW/BDW
and GEN9+ versions of these macros and the power well ops using them
will be done in follow-up patches.
v2:
- Rebased on v2 of patch 2.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-3-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make the I830 power well ID assignment explicit for consistency.
v2:
- s/GEN2/I830/ in the comment, since other GEN2s don't have the power
well. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-2-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, the power well IDs are defined in separate platform specific enums,
which isn't ideal for the following reasons:
- the IDs are used by helpers like lookup_power_well() in a platform
independent way
- the always-on power well is used by multiple platforms and so needs
now separate IDs, although these IDs refer to the same thing
To make things more consistent use a single enum instead of the two
separate ones, listing the IDs per platform (or set of very similar
platforms like all GEN9/10). Replace the separate always-on power
well IDs with a single ID.
While at it also add a note clarifying the distinction between regular
power wells that follow a common programming pattern and custom ones
that are programmed in some other way. The IDs for regular power wells
need to stay fixed, since they also define the request and state HW flag
positions in their corresponding power well control register(s).
v2:
- Add comment about id to req,status bit mapping to the enum. (Rodrigo)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170711204236.5618-1-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The power well IDs are used for lookup, so they must be unique on a
given platform; ensure this on CHV. This didn't cause an actual problem
since we didn't need to look up power wells which happened to share an
ID.
Mark this new power well as custom, since its programming pattern
doesn't follow that of the rest of VLV/CHV power wells.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1499352040-8819-2-git-send-email-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PLLs are the source clocks for the DDIs so in order
to determine the ddi clock we need to check the PLL
configuration.
v2: Mika pointed out that 24 was hardcoded while it
should consider ref clock that can be either 24KHz
or 19.2KHz on CNL.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1499374321-31152-1-git-send-email-rodrigo.vivi@intel.com
The Cursor Coeff is lower 6 bits in the PORT_TX_DW4 register
and hence the CURSOR_COEFF_MASK should be (0x3F << 0)
Fixes: 04416108cc ("drm/i915/cnl: Add registers related to voltage
swing sequences.")
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1498785241-21138-1-git-send-email-manasi.d.navare@intel.com
Paulo noticed that we were missing few bits clear
before writing values back to the register on
these RMW MMIO operations.
v2: Remove "POST_" from CURSOR_COEFF_MASK. (Paulo).
v3: Remove unnecessary braces. (Jani).
Fixes: cf54ca8bc5 ("drm/i915/cnl: Implement voltage swing sequence.")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497897572-22520-1-git-send-email-rodrigo.vivi@intel.com
Enables access to OA unit metrics for BDW, CHV, SKL and BXT which all
share (more-or-less) the same OA unit design.
Of particular note in comparison to Haswell: some OA unit HW config
state has become per-context state and as a consequence it is somewhat
more complicated to manage synchronous state changes from the cpu while
there's no guarantee of what context (if any) is currently actively
running on the gpu.
The periodic sampling frequency which can be particularly useful for
system-wide analysis (as opposed to command stream synchronised
MI_REPORT_PERF_COUNT commands) is perhaps the most surprising state to
have become per-context save and restored (while the OABUFFER
destination is still a shared, system-wide resource).
This support for gen8+ takes care to consider a number of timing
challenges involved in synchronously updating per-context state
primarily by programming all config state from the cpu and updating all
current and saved contexts synchronously while the OA unit is still
disabled.
The driver intentionally avoids depending on command streamer
programming to update OA state considering the lack of synchronization
between the automatic loading of OACTXCONTROL state (that includes the
periodic sampling state and enable state) on context restore and the
parsing of any general purpose BB the driver can control. I.e. this
implementation is careful to avoid the possibility of a context restore
temporarily enabling any out-of-date periodic sampling state. In
addition to the risk of transiently-out-of-date state being loaded
automatically; there are also internal HW latencies involved in the
loading of MUX configurations which would be difficult to account for
from the command streamer (and we only want to enable the unit when once
the MUX configuration is complete).
Since the Gen8+ OA unit design no longer supports clock gating the unit
off for a single given context (which effectively stopped any progress
of counters while any other context was running) and instead supports
tagging OA reports with a context ID for filtering on the CPU, it means
we can no longer hide the system-wide progress of counters from a
non-privileged application only interested in metrics for its own
context. Although we could theoretically try and subtract the progress
of other contexts before forwarding reports via read() we aren't in a
position to filter reports captured via MI_REPORT_PERF_COUNT commands.
As a result, for Gen8+, we always require the
dev.i915.perf_stream_paranoid to be unset for any access to OA metrics
if not root.
v5: Drain submitted requests when enabling metric set to ensure no
lite-restore erases the context image we just updated (Lionel)
v6: In addition to drain, switch to kernel context & update all
context in place (Chris)
v7: Add missing mutex_unlock() if switching to kernel context fails
(Matthew)
v8: Simplify OA period/flex-eu-counters programming by using the
batchbuffer instead of modifying ctx-image (Lionel)
v9: Back to updating the context image (due to erroneous testing,
batchbuffer programming the OA unit doesn't actually work)
(Lionel)
Pin context before updating context image (Chris)
Drop MMIO programming now that we switch to a kernel context with
right values in initial context image (Chris)
v10: Just pin_map the contexts we want to modify or let the
configuration happen on first use (Chris)
v11: Update kernel context OA config through the batchbuffer rather
than on the fly ctx-image update (Lionel)
v12: Rework OA context registers update again by swithing away from
user contexts and reconfiguring the kernel context through the
batchbuffer and updating all the other contexts' context image.
Also take care to lock slice/subslice configuration when OA is
on. (Lionel)
v13: Request rpcs updates on all engine when updating the OA config
(Lionel)
v14: Drop any kind of rpcs management now that we monitor sseu
configuration changes in a later patch (Lionel)
Remove usleep after programming the NOA configs on Gen8+, this
doesn't seem to be needed (Lionel)
v15: Respect coding style for block comments (Chris)
v16: Add missing i915_add_request() in case we fail to emit OA
configuration (Matthew)
Signed-off-by: Robert Bragg <robert@sixbynine.org>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com> \o/
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
This is an important part of the DDI initalization as well as
for changing the voltage during DisplayPort link training.
This new sequence for Cannonlake is more like Broxton style
but still with different registers, different table and
different steps.
v2: Do not write to DW4_GRP to avoid overwrite individual loadgen.
Fix PORT_CL_DW5 SUS Clock Config set.
v3: As previous platforms use only eDP table if low voltage was
requested.
v4: fix Werror:maybe uninitialized (Paulo)
v5: Rebase on top of dw2_swing_sel changes
on previous patches.
v6: Using flexible SCALING_MODE_SEL(x).
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-11-git-send-email-rodrigo.vivi@intel.com
This are the registers and bits needed for the voltage swing
sequence on Cannonlake.
v2: Remove CL_DW5 that was wrongly defined.
v3: Use (1 << 1) instead of (1<<1) as Paulo suggested
Change DW2 swing sel upper and lower macros to do the
bit selection instead of definint a table that doesn't
match the spec. It is based on a Manasi version of it.
Credits-to: Manasi.
v4: Let SCALING_MODE_SEL flexible. (Manasi)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-9-git-send-email-rodrigo.vivi@intel.com
Also new registers can have different mmio offsets
per different lane per port.
v2: Use _PICK as PORT3 instead of creating a new
macro with if per port.
v3: Use _PICK directly on MMIO_PORT6. While MMIO_PORT
isn't flexible enough let's continue with MMIO_PORT6
as we have MMIO_PORT3.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-8-git-send-email-rodrigo.vivi@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Although CNL follows PLL initialization more like Skylake
than Broxton we have a completely different initialization
sequence and registers used.
One big difference from SKL is that CDCLK PLL is now
exclusive (ADPLL) and for DDIs and MIPI we need to use
DFGPLLs 0, 1 or 2.
v2: Accept all Ander's suggestions and fixes:
- Registers and bits names prefix
- Group pll functions
- bits masks fixes
- remove read and modify on cfgcr1
- fix cfgcr0 setup
v3: Set SSC_ENABLE for DP.
Fix HDMI_MODE cfgcr0.
Avoid touch cfgcr0 on DP.
Add missed else on dpll_mgr definition so we use cnl one, not hsw.
v3: Centra freq should be always set to default and change bits
definitions to (1 << 1) instead of (1<<1). (by Paulo)
v4: Rebased.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Kahola, Mika <mika.kahola@intel.com>
Reviewed-by: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-7-git-send-email-rodrigo.vivi@intel.com
One of the steps for PLL (un)initialization is to (un)map
the correspondent DDI that is actually using that PLL.
So, let's do this step following the places already stablished
and used so far, although spec put this as part of PLL
initialization sequences.
v2: Use proper prefix on bits names as suggested by Ander.
v3: Add missed "~". Without that the logic was inverted
so we were disabling interrupts.
Credits-to: Clinton
Credits-to: Art
v4: Spec is getting updated to do DDI -> PLL mapping
and clock on in 2 separated reg writes. (Paulo)
Also update bits definitions to use space
(1 << 1) instead of (1<<1). (Paulo)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Kahola, Mika <mika.kahola@intel.com>
Cc: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Kahola, Mika <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-5-git-send-email-rodrigo.vivi@intel.com
Implement the CNL display init/uninit sequence as outlined in Bspec.
Quite similar to SKL/BXT. The main complicaiton is probably the extra
procmon setup we must do based on the process/voltage information we
can read out from some register.
v2: s/skl_dbuf/gen9_dbuf/ to follow upstream
bxt needed a cdclk sanitize step, so let's add it for cnl too
v3: s/CHICKEN_MISC_1/CHICKEN_MISC_2/ (Ander)
v4: Rebased by Rodrigo after Ville's cdclk rework
v5: Removed unecessary Aux IO forced enable/disable, Fix DW10 setup
Fix procpon Mask. (Credits-to Paulo and Clint)
Remove A0 workaround.
v6: Rebased on top of recent code (Rodrigo).
v7: Respect the order of sanitize_ after set_
(Done by Rodrigo, Requested by Ville)
v8: Commit message updated to matvh v5 changes besides
Remove unused DW8 and an extra blank line. (all noticed
by Imre).
v9: Remove __attribute__((unused)) added on latest version
of drm/i915/cnl: Implement .set_cdclk() for CNL.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-3-git-send-email-rodrigo.vivi@intel.com
Add support for reading out the cdclk frequency from the hardware on
CNL. Very similar to BXT, with a few new twists and turns:
* the PLL is now called CDCLK PLL, not DE PLL
* reference clock can be 24 MHz in addition to the 19.2 MHz BXT had
* the ratio now lives in the PLL enable register
* Only 1x and 2x CD2X dividers are supported
v2: Deal with PLL lock bit the same way as BXT/SKL do now
v3: DSSM refclk indicator is bit 31 not 24 (Ander)
v4: Rebased by Rodrigo after Ville's cdclk rework.
v5: Set cdclk to the ref clock as previous platforms. (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-1-git-send-email-rodrigo.vivi@intel.com
Let's be picky and just use PICK directly.
So we can extend this later without creating
a new PORT_X por every new number of ports we
have to handle.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496700722-13755-1-git-send-email-rodrigo.vivi@intel.com
CNL power wells are very similar to SKL, with the exception that the
misc IO well has been split into separate AUX IO wells.
Not sure if DMC is supposed to manage the AUX wells for us or not.
Let's assume so for now.
v2: DDI A power well wants DDI A domains, not DDI B domains
v3: s/BIT/BIT_ULL and add proper Aux IO domains. (Rodrigo)
v4: Remove PW_DDI_E. Not supported on Current CNL SKUs. (Rodrigo).
v5: Removed DDI_E_IO_DOMAINS and moved PORT_DDI_E_IO to DDI_A_IO
for the same reasons as v4 when we found out that current CNL
SKUs don't have the full port E split.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-10-git-send-email-rodrigo.vivi@intel.com
