Make return value void since functions never returns meaningfull value.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions jme_restart_tx_engine(), jme_pause_rx() and
jme_resume_rx() are not used. Removing them fixes the following warnings
when building with clang:
drivers/net/ethernet/jme.c:694:1: error: unused function
'jme_restart_tx_engine' [-Werror,-Wunused-function]
drivers/net/ethernet/jme.c:2393:20: error: unused function
'jme_pause_rx' [-Werror,-Wunused-function]
drivers/net/ethernet/jme.c:2406:20: error: unused function
'jme_resume_rx' [-Werror,-Wunused-function]
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somehow, I missed a healthy number of ethernet drivers in the last pass.
Most of these drivers either were in need of an updated max_mtu to make
jumbo frames possible to enable again. In a few cases, also setting a
different min_mtu to match previous lower bounds. There are also a few
drivers that had no upper bounds checking, so they're getting a brand new
ETH_MAX_MTU that is identical to IP_MAX_MTU, but accessible by includes
all ethernet and ethernet-like drivers all have already.
acenic:
- min_mtu = 0, max_mtu = 9000
amazon/ena:
- min_mtu = 128, max_mtu = adapter->max_mtu
amd/xgbe:
- min_mtu = 0, max_mtu = 9000
sb1250:
- min_mtu = 0, max_mtu = 1518
cxgb3:
- min_mtu = 81, max_mtu = 65535
cxgb4:
- min_mtu = 81, max_mtu = 9600
cxgb4vf:
- min_mtu = 81, max_mtu = 65535
benet:
- min_mtu = 256, max_mtu = 9000
ibmveth:
- min_mtu = 68, max_mtu = 65535
ibmvnic:
- min_mtu = adapter->min_mtu, max_mtu = adapter->max_mtu
- remove now redundant ibmvnic_change_mtu
jme:
- min_mtu = 1280, max_mtu = 9202
mv643xx_eth:
- min_mtu = 64, max_mtu = 9500
mlxsw:
- min_mtu = 0, max_mtu = 65535
- Basically bypassing the core checks, and instead relying on dynamic
checks in the respective switch drivers' ndo_change_mtu functions
ns83820:
- min_mtu = 0
- remove redundant ns83820_change_mtu, only checked for mtu > 1500
netxen:
- min_mtu = 0, max_mtu = 8000 (P2), max_mtu = 9600 (P3)
qlge:
- min_mtu = 1500, max_mtu = 9000
- driver only supports setting mtu to 1500 or 9000, so the core check only
rules out < 1500 and > 9000, qlge_change_mtu still needs to check that
the value is 1500 or 9000
qualcomm/emac:
- min_mtu = 46, max_mtu = 9194
xilinx_axienet:
- min_mtu = 64, max_mtu = 9000
Fixes: 61e84623ac ("net: centralize net_device min/max MTU checking")
CC: netdev@vger.kernel.org
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Netanel Belgazal <netanel@annapurnalabs.com>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
CC: John Allen <jallen@linux.vnet.ibm.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Jiri Pirko <jiri@mellanox.com>
CC: Ido Schimmel <idosch@mellanox.com>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Timur Tabi <timur@codeaurora.org>
CC: Anirudha Sarangi <anirudh@xilinx.com>
CC: John Linn <John.Linn@xilinx.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function compiles to 895 bytes of machine code.
Clearly, this isn't a time-critical function.
For one, it has a number of udelay(1) calls.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: David S. Miller <davem@davemloft.net>
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
According to Documentation/power/devices.txt
The driver should not use device_set_wakeup_enable() which is the policy
for user to decide.
Using device_init_wakeup() to initialize dev->power.should_wakeup and
dev->power.can_wakeup on driver initialization.
And use device_may_wakeup() on suspend to decide if WoL function should
be enabled on NIC.
Reported-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise it might be back on resume right after going to suspend in
some hardware.
Reported-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The JMC260 network card fails to suspend/resume because the call to
jme_start_irq() was too early, moving the call to jme_start_irq() after
the call to jme_reset_link() makes it work.
Prior this change suspend/resume would fail unless /sys/power/pm_async=0
was explicitly specified.
Relevant bug report: https://bugzilla.kernel.org/show_bug.cgi?id=112351
Signed-off-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using kzalloc saves a tiny bit on .text.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calls to tasklet_hi_enable are replaced by calls to
tasklet_enable since the 2 functions are redundant.
Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In my recent fix (76a691d0a: fix dma unmap warning), Ben Hutchings noted that my
loop count was incorrect. Where j started at startidx, it should have started
at zero, and gone on for count entries, not to endidx. Additionally, a DMA
resource exhaustion should drop the frame and (for now), return
NETDEV_TX_OK, not NETEV_TX_BUSY. This patch fixes both of those issues:
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Ben Hutchings <ben@decadent.org.uk>
CC: "David S. Miller" <davem@davemloft.net>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The jme driver forgot to check the return status from pci_map_page in its tx
path, causing a dma api warning on unmap. Easy fix, just do the check and
augment the tx path to tell the stack that the driver is busy so we re-queue the
frame.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_kfree_skb_any in jme_expand_header that
can be called in hard irq and other contexts, on the failure
path where the skb is dropped.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.
Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 82dc3c63 ("net: introduce NAPI_POLL_WEIGHT")
netif_napi_add() produces an error message if a NAPI poll weight
greater than 64 is requested.
jme requests a quarter of the rx ring size as the NAPI weight.
jme's rx ring size is 1 << 9 = 512.
Use the standard NAPI weight.
v2: proper reference to the related commit
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_enable_device() will set device power state to D0,
so it's no need to do it again in jme_init_one().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 175c0dff, drivers uses tasklet_kill to avoid put disabled tasklet
on the tasklet vec. But some of the drivers uses tasklet_init & tasklet_disable
in the driver init code, then tasklet_enable when it is opened. This makes
tasklet_enable on a killed tasklet and make ksoftirqd crazy then. Normally,
drivers should use tasklet_init/tasklet_kill on device open/remove, and use
tasklet_disable/tasklet_enable on device suspend/resume.
Reported-by: Peter Wu <lekensteyn@gmail.com>
Tested-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Some driver uses tasklet_disable in device remove/close process,
tasklet_disable will inc tasklet->count and return. If the tasklet
is not handled yet because some softirq pressure, the tasklet will
placed on the tasklet_vec, never have a chance to excute. This might
lead to ksoftirqd heavy loaded, wakeup with pending_softirq, but
tasklet is disabled. tasklet_kill should be used in this case.
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on patch from Matthew Garrett <mjg@redhat.com> (https://lkml.org/lkml/2011/11/11/168).
http://driveragent.com/archive/30421/7-0-14 indicates that ASPM is
disabled on the 250 and 260. Duplicate for sanity.
Fixes random RX engine hangs I experienced with JMC250 on Clevo W270HU.
Signed-off-by: Kevin Baradon <kevin.baradon@gmail.com>
Cc: Guo-Fu Tseng <cooldavid@cooldavid.org>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the netpoll function to support netconsole. Tested and works
fine on my "JMC250 PCI Express Gigabit Ethernet Controller" (PCI ID 0250).
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/sfc/rx.c
Overlapping changes in drivers/net/ethernet/sfc/rx.c, one to change
the rx_buf->is_page boolean into a set of u16 flags, and another to
adjust how ->ip_summed is initialized.
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the RX FIFO flush watermark lower.
According to Federico and JMicron's reply,
setting it to 16QW would be stable on most platforms.
Otherwise, user might experience packet drop issue.
CC: stable@kernel.org
Reported-by: Federico Quagliata <federico@quagliata.org>
Fixed-by: Federico Quagliata <federico@quagliata.org>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To perform PHY calibration and set a different EA value by chip ID,
Whenever the NIC chip power on, ie booting or resuming, we need to
force HW to calibrate PHY parameter again, and also set a proper EA
value which gather from experiment.
Those procedures help to reduce compatible issues(NIC is unable to link
up in some special case) in giga speed.
Signed-off-by: AriesLee <AriesLee@jmicron.com>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Save some punctuation by using bool type's property equivalent to
doubled negation operator.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Perform another round of floor sweeping, converting the .get_drvinfo
routines of additional drivers from strcpy to strlcpy along with
some conversion of sprintf to snprintf.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Guo-Fu Tseng <cooldavid@cooldavid.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the JME driver into drivers/net/ethernet/ and make the
necessary Kconfig and Makefile changes.
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
